My self-made 3D-printable designs, mainly in OpenSCAD
Vous ne pouvez pas sélectionner plus de 25 sujets Les noms de sujets doivent commencer par une lettre ou un nombre, peuvent contenir des tirets ('-') et peuvent comporter jusqu'à 35 caractères.

Cura_Fabrikator_Mini.ini 11KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262
  1. [profile]
  2. layer_height = 0.2
  3. wall_thickness = 0.8
  4. retraction_enable = True
  5. solid_layer_thickness = 0.8
  6. fill_density = 15
  7. print_speed = 20
  8. print_temperature = 190
  9. print_temperature2 = 0
  10. print_temperature3 = 0
  11. print_temperature4 = 0
  12. print_temperature5 = 0
  13. print_bed_temperature = 60
  14. support = None
  15. platform_adhesion = None
  16. support_dual_extrusion = Both
  17. wipe_tower = False
  18. wipe_tower_volume = 15
  19. ooze_shield = False
  20. filament_diameter = 1.75
  21. filament_diameter2 = 0
  22. filament_diameter3 = 0
  23. filament_diameter4 = 0
  24. filament_diameter5 = 0
  25. filament_flow = 100.0
  26. nozzle_size = 0.4
  27. retraction_speed = 40.0
  28. retraction_amount = 4.5
  29. retraction_dual_amount = 16.5
  30. retraction_min_travel = 1.5
  31. retraction_combing = All
  32. retraction_minimal_extrusion = 0.02
  33. retraction_hop = 0.0
  34. bottom_thickness = 0.3
  35. layer0_width_factor = 100
  36. object_sink = 0.0
  37. overlap_dual = 0.15
  38. travel_speed = 30.0
  39. bottom_layer_speed = 18
  40. infill_speed = 20
  41. solidarea_speed = 20
  42. inset0_speed = 20
  43. insetx_speed = 20
  44. cool_min_layer_time = 15
  45. fan_enabled = True
  46. skirt_line_count = 1
  47. skirt_gap = 0.5
  48. skirt_minimal_length = 300.0
  49. fan_full_height = 0.5
  50. fan_speed = 100
  51. fan_speed_max = 100
  52. cool_min_feedrate = 10
  53. cool_head_lift = False
  54. solid_top = True
  55. solid_bottom = True
  56. fill_overlap = 15
  57. perimeter_before_infill = False
  58. support_type = Lines
  59. support_angle = 60
  60. support_fill_rate = 25
  61. support_xy_distance = 0.7
  62. support_z_distance = 0.15
  63. spiralize = False
  64. simple_mode = False
  65. brim_line_count = 5
  66. raft_margin = 3.0
  67. raft_line_spacing = 3.0
  68. raft_base_thickness = 0.3
  69. raft_base_linewidth = 1.0
  70. raft_interface_thickness = 0.27
  71. raft_interface_linewidth = 0.4
  72. raft_airgap_all = 0.0
  73. raft_airgap = 0.22
  74. raft_surface_layers = 2
  75. raft_surface_thickness = 0.27
  76. raft_surface_linewidth = 0.4
  77. fix_horrible_union_all_type_a = True
  78. fix_horrible_union_all_type_b = False
  79. fix_horrible_use_open_bits = False
  80. fix_horrible_extensive_stitching = False
  81. plugin_config =
  82. object_center_x = -1
  83. object_center_y = -1
  84. [alterations]
  85. start.gcode = ;Sliced at: {day} {date} {time}
  86. ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  87. ;Print time: {print_time}
  88. ;Filament used: {filament_amount}m {filament_weight}g
  89. ;Filament cost: {filament_cost}
  90. ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
  91. ;M109 S{print_temperature} ;Uncomment to add your own temperature line
  92. G21 ;metric values
  93. G90 ;absolute positioning
  94. M82 ;set extruder to absolute mode
  95. M107 ;start with the fan off
  96. M140 S{print_bed_temperature} ; begin heating bed
  97. M104 S{print_temperature} ; begin heating nozzle
  98. G28 X0 Y0 ;move X/Y to min endstops
  99. G28 Z0 ;move Z to min endstops
  100. G1 Z10.0 F{travel_speed} ;move the platform down 15mm
  101. M190 S{print_bed_temperature} ; Wait for bed temp
  102. M109 S{print_temperature} ; Wait for nozzle temp
  103. G92 E0 ;zero the extruded length
  104. G1 F200 E1 ;extrude 1mm of feed stock
  105. G92 E0 ;zero the extruded length again
  106. G1 F{travel_speed}
  107. ;Put printing message on LCD screen
  108. M117 Printing...
  109. end.gcode = ;End GCode
  110. M104 S0 ;extruder heater off
  111. M140 S0 ;heated bed heater off (if you have it)
  112. G91 ;relative positioning
  113. G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
  114. G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
  115. G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
  116. M84 ;steppers off
  117. G90 ;absolute positioning
  118. ;{profile_string}
  119. start2.gcode = ;Sliced at: {day} {date} {time}
  120. ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  121. ;Print time: {print_time}
  122. ;Filament used: {filament_amount}m {filament_weight}g
  123. ;Filament cost: {filament_cost}
  124. ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
  125. ;M104 S{print_temperature} ;Uncomment to add your own temperature line
  126. ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
  127. ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
  128. G21 ;metric values
  129. G90 ;absolute positioning
  130. M107 ;start with the fan off
  131. G28 X0 Y0 ;move X/Y to min endstops
  132. G28 Z0 ;move Z to min endstops
  133. G1 Z15.0 F{travel_speed} ;move the platform down 15mm
  134. T1 ;Switch to the 2nd extruder
  135. G92 E0 ;zero the extruded length
  136. G1 F200 E10 ;extrude 10mm of feed stock
  137. G92 E0 ;zero the extruded length again
  138. G1 F200 E-{retraction_dual_amount}
  139. T0 ;Switch to the first extruder
  140. G92 E0 ;zero the extruded length
  141. G1 F200 E10 ;extrude 10mm of feed stock
  142. G92 E0 ;zero the extruded length again
  143. G1 F{travel_speed}
  144. ;Put printing message on LCD screen
  145. M117 Printing...
  146. end2.gcode = ;End GCode
  147. M104 T0 S0 ;extruder heater off
  148. M104 T1 S0 ;extruder heater off
  149. M140 S0 ;heated bed heater off (if you have it)
  150. G91 ;relative positioning
  151. G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
  152. G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
  153. G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
  154. M84 ;steppers off
  155. G90 ;absolute positioning
  156. ;{profile_string}
  157. start3.gcode = ;Sliced at: {day} {date} {time}
  158. ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  159. ;Print time: {print_time}
  160. ;Filament used: {filament_amount}m {filament_weight}g
  161. ;Filament cost: {filament_cost}
  162. ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
  163. ;M104 S{print_temperature} ;Uncomment to add your own temperature line
  164. ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
  165. ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
  166. G21 ;metric values
  167. G90 ;absolute positioning
  168. M107 ;start with the fan off
  169. G28 X0 Y0 ;move X/Y to min endstops
  170. G28 Z0 ;move Z to min endstops
  171. G1 Z15.0 F{travel_speed} ;move the platform down 15mm
  172. T2 ;Switch to the 3rd extruder
  173. G92 E0 ;zero the extruded length
  174. G1 F200 E10 ;extrude 10mm of feed stock
  175. G92 E0 ;zero the extruded length again
  176. G1 F200 E-{retraction_dual_amount}
  177. T1 ;Switch to the 2nd extruder
  178. G92 E0 ;zero the extruded length
  179. G1 F200 E10 ;extrude 10mm of feed stock
  180. G92 E0 ;zero the extruded length again
  181. G1 F200 E-{retraction_dual_amount}
  182. T0 ;Switch to the first extruder
  183. G92 E0 ;zero the extruded length
  184. G1 F200 E10 ;extrude 10mm of feed stock
  185. G92 E0 ;zero the extruded length again
  186. G1 F{travel_speed}
  187. ;Put printing message on LCD screen
  188. M117 Printing...
  189. end3.gcode = ;End GCode
  190. M104 T0 S0 ;extruder heater off
  191. M104 T1 S0 ;extruder heater off
  192. M104 T2 S0 ;extruder heater off
  193. M140 S0 ;heated bed heater off (if you have it)
  194. G91 ;relative positioning
  195. G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
  196. G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
  197. G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
  198. M84 ;steppers off
  199. G90 ;absolute positioning
  200. ;{profile_string}
  201. start4.gcode = ;Sliced at: {day} {date} {time}
  202. ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
  203. ;Print time: {print_time}
  204. ;Filament used: {filament_amount}m {filament_weight}g
  205. ;Filament cost: {filament_cost}
  206. ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
  207. ;M104 S{print_temperature} ;Uncomment to add your own temperature line
  208. ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
  209. ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
  210. ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
  211. G21 ;metric values
  212. G90 ;absolute positioning
  213. M107 ;start with the fan off
  214. G28 X0 Y0 ;move X/Y to min endstops
  215. G28 Z0 ;move Z to min endstops
  216. G1 Z15.0 F{travel_speed} ;move the platform down 15mm
  217. T3 ;Switch to the 4th extruder
  218. G92 E0 ;zero the extruded length
  219. G1 F200 E10 ;extrude 10mm of feed stock
  220. G92 E0 ;zero the extruded length again
  221. G1 F200 E-{retraction_dual_amount}
  222. T2 ;Switch to the 3rd extruder
  223. G92 E0 ;zero the extruded length
  224. G1 F200 E10 ;extrude 10mm of feed stock
  225. G92 E0 ;zero the extruded length again
  226. G1 F200 E-{retraction_dual_amount}
  227. T1 ;Switch to the 2nd extruder
  228. G92 E0 ;zero the extruded length
  229. G1 F200 E10 ;extrude 10mm of feed stock
  230. G92 E0 ;zero the extruded length again
  231. G1 F200 E-{retraction_dual_amount}
  232. T0 ;Switch to the first extruder
  233. G92 E0 ;zero the extruded length
  234. G1 F200 E10 ;extrude 10mm of feed stock
  235. G92 E0 ;zero the extruded length again
  236. G1 F{travel_speed}
  237. ;Put printing message on LCD screen
  238. M117 Printing...
  239. end4.gcode = ;End GCode
  240. M104 T0 S0 ;extruder heater off
  241. M104 T1 S0 ;extruder heater off
  242. M104 T2 S0 ;extruder heater off
  243. M104 T3 S0 ;extruder heater off
  244. M140 S0 ;heated bed heater off (if you have it)
  245. G91 ;relative positioning
  246. G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
  247. G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
  248. G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
  249. M84 ;steppers off
  250. G90 ;absolute positioning
  251. ;{profile_string}
  252. support_start.gcode =
  253. support_end.gcode =
  254. cool_start.gcode =
  255. cool_end.gcode =
  256. replace.csv =
  257. preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
  258. ;This code is added before the T(n)
  259. postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
  260. ;This code is added after the T(n)