initial commit

.gitignore

@@ -0,0 +1,4 @@
+.directory
+
+sensor/build
+sensor/sensor.*

.gitmodules

@@ -0,0 +1,3 @@
+[submodule "sensor/v-usb"]
+	path = sensor/v-usb
+	url = https://github.com/obdev/v-usb

README.md

@@ -0,0 +1 @@
+# AutoBrightness

sensor/Makefile

@@ -0,0 +1,622 @@
+# Hey Emacs, this is a -*- makefile -*-
+#----------------------------------------------------------------------------
+# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
+#
+# Released to the Public Domain
+#
+# Additional material for this makefile was written by:
+# Peter Fleury
+# Tim Henigan
+# Colin O'Flynn
+# Reiner Patommel
+# Markus Pfaff
+# Sander Pool
+# Frederik Rouleau
+# Carlos Lamas
+#
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device, using avrdude.
+#                Please customize the avrdude settings below first!
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+
+# MCU name
+MCU = attiny85
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the 
+#     processor frequency. You can then use this symbol in your source code to 
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#     Typical values are:
+#         F_CPU =  1000000
+#         F_CPU =  1843200
+#         F_CPU =  2000000
+#         F_CPU =  3686400
+#         F_CPU =  4000000
+#         F_CPU =  7372800
+#         F_CPU =  8000000
+#         F_CPU = 11059200
+#         F_CPU = 14745600
+#         F_CPU = 16000000
+#         F_CPU = 18432000
+#         F_CPU = 20000000
+F_CPU = 16000000
+
+
+# Output format. (can be srec, ihex, binary)
+FORMAT = ihex
+
+
+# Target file name (without extension).
+TARGET = sensor
+
+
+# Object files directory
+#     To put object files in current directory, use a dot (.), do NOT make
+#     this an empty or blank macro!
+OBJDIR = build
+
+
+# List C source files here. (C dependencies are automatically generated.)
+SRC = v-usb/usbdrv/usbdrv.c v-usb/usbdrv/oddebug.c
+SRC += src/main.c
+
+
+# List C++ source files here. (C dependencies are automatically generated.)
+CPPSRC =
+
+
+# List Assembler source files here.
+#     Make them always end in a capital .S.  Files ending in a lowercase .s
+#     will not be considered source files but generated files (assembler
+#     output from the compiler), and will be deleted upon "make clean"!
+#     Even though the DOS/Win* filesystem matches both .s and .S the same,
+#     it will preserve the spelling of the filenames, and gcc itself does
+#     care about how the name is spelled on its command-line.
+ASRC = v-usb/usbdrv/usbdrvasm.S
+
+
+# Optimization level, can be [0, 1, 2, 3, s]. 
+#     0 = turn off optimization. s = optimize for size.
+#     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
+OPT = s
+
+
+# Debugging format.
+#     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
+#     AVR Studio 4.10 requires dwarf-2.
+#     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
+DEBUG = dwarf-2
+
+
+# List any extra directories to look for include files here.
+#     Each directory must be seperated by a space.
+#     Use forward slashes for directory separators.
+#     For a directory that has spaces, enclose it in quotes.
+EXTRAINCDIRS = include v-usb/usbdrv
+
+
+# Compiler flag to set the C Standard level.
+#     c89   = "ANSI" C
+#     gnu89 = c89 plus GCC extensions
+#     c99   = ISO C99 standard (not yet fully implemented)
+#     gnu99 = c99 plus GCC extensions
+CSTANDARD = -std=gnu99
+
+
+# Place -D or -U options here for C sources
+CDEFS = -DF_CPU=$(F_CPU)UL
+
+
+# Place -D or -U options here for ASM sources
+ADEFS = -DF_CPU=$(F_CPU)
+
+
+# Place -D or -U options here for C++ sources
+CPPDEFS = -DF_CPU=$(F_CPU)UL
+#CPPDEFS += -D__STDC_LIMIT_MACROS
+#CPPDEFS += -D__STDC_CONSTANT_MACROS
+
+
+DEPDIR = $(OBJDIR)/dependencies
+
+
+#---------------- Compiler Options C ----------------
+#  -g*:          generate debugging information
+#  -O*:          optimization level
+#  -f...:        tuning, see GCC manual and avr-libc documentation
+#  -Wall...:     warning level
+#  -Wa,...:      tell GCC to pass this to the assembler.
+#    -adhlns...: create assembler listing
+CFLAGS = -g$(DEBUG)
+CFLAGS += $(CDEFS)
+CFLAGS += -O$(OPT)
+CFLAGS += -funsigned-char
+CFLAGS += -funsigned-bitfields
+CFLAGS += -fpack-struct
+CFLAGS += -fshort-enums
+CFLAGS += -Wall
+CFLAGS += -Wstrict-prototypes
+#CFLAGS += -mshort-calls
+#CFLAGS += -fno-unit-at-a-time
+#CFLAGS += -Wundef
+#CFLAGS += -Wunreachable-code
+#CFLAGS += -Wsign-compare
+CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
+CFLAGS += $(CSTANDARD)
+
+
+#---------------- Compiler Options C++ ----------------
+#  -g*:          generate debugging information
+#  -O*:          optimization level
+#  -f...:        tuning, see GCC manual and avr-libc documentation
+#  -Wall...:     warning level
+#  -Wa,...:      tell GCC to pass this to the assembler.
+#    -adhlns...: create assembler listing
+CPPFLAGS = -g$(DEBUG)
+CPPFLAGS += $(CPPDEFS)
+CPPFLAGS += -O$(OPT)
+CPPFLAGS += -funsigned-char
+CPPFLAGS += -funsigned-bitfields
+CPPFLAGS += -fpack-struct
+CPPFLAGS += -fshort-enums
+CPPFLAGS += -fno-exceptions
+CPPFLAGS += -Wall
+CPPFLAGS += -Wundef
+#CPPFLAGS += -mshort-calls
+#CPPFLAGS += -fno-unit-at-a-time
+#CPPFLAGS += -Wstrict-prototypes
+#CPPFLAGS += -Wunreachable-code
+#CPPFLAGS += -Wsign-compare
+CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
+#CPPFLAGS += $(CSTANDARD)
+
+#---------------- Assembler Options ----------------
+#  -Wa,...:   tell GCC to pass this to the assembler.
+#  -adhlns:   create listing
+#  -gstabs:   have the assembler create line number information; note that
+#             for use in COFF files, additional information about filenames
+#             and function names needs to be present in the assembler source
+#             files -- see avr-libc docs [FIXME: not yet described there]
+#  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
+#       dump that will be displayed for a given single line of source input.
+ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
+
+
+#---------------- Library Options ----------------
+# Minimalistic printf version
+PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
+
+# Floating point printf version (requires MATH_LIB = -lm below)
+PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
+
+# If this is left blank, then it will use the Standard printf version.
+PRINTF_LIB = 
+#PRINTF_LIB = $(PRINTF_LIB_MIN)
+#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
+
+
+# Minimalistic scanf version
+SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
+
+# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
+SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
+
+# If this is left blank, then it will use the Standard scanf version.
+SCANF_LIB = 
+#SCANF_LIB = $(SCANF_LIB_MIN)
+#SCANF_LIB = $(SCANF_LIB_FLOAT)
+
+
+MATH_LIB = -lm
+
+
+# List any extra directories to look for libraries here.
+#     Each directory must be seperated by a space.
+#     Use forward slashes for directory separators.
+#     For a directory that has spaces, enclose it in quotes.
+EXTRALIBDIRS = 
+
+
+
+#---------------- External Memory Options ----------------
+
+# 64 KB of external RAM, starting after internal RAM (ATmega128!),
+# used for variables (.data/.bss) and heap (malloc()).
+#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
+
+# 64 KB of external RAM, starting after internal RAM (ATmega128!),
+# only used for heap (malloc()).
+#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
+
+EXTMEMOPTS =
+
+
+
+#---------------- Linker Options ----------------
+#  -Wl,...:     tell GCC to pass this to linker.
+#    -Map:      create map file
+#    --cref:    add cross reference to  map file
+LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
+LDFLAGS += $(EXTMEMOPTS)
+LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
+LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
+#LDFLAGS += -T linker_script.x
+
+
+
+#---------------- Programming Options (avrdude) ----------------
+
+# Programming hardware
+# Type: avrdude -c ?
+# to get a full listing.
+#
+AVRDUDE_PROGRAMMER = avrispmkII
+
+# com1 = serial port. Use lpt1 to connect to parallel port.
+AVRDUDE_PORT = usb    # programmer connected to serial device
+
+AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
+#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
+
+
+# Uncomment the following if you want avrdude's erase cycle counter.
+# Note that this counter needs to be initialized first using -Yn,
+# see avrdude manual.
+#AVRDUDE_ERASE_COUNTER = -y
+
+# Uncomment the following if you do /not/ wish a verification to be
+# performed after programming the device.
+#AVRDUDE_NO_VERIFY = -V
+
+# Increase verbosity level.  Please use this when submitting bug
+# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
+# to submit bug reports.
+#AVRDUDE_VERBOSE = -v -v
+
+AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
+AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
+AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
+
+
+
+#---------------- Debugging Options ----------------
+
+# For simulavr only - target MCU frequency.
+DEBUG_MFREQ = $(F_CPU)
+
+# Set the DEBUG_UI to either gdb or insight.
+# DEBUG_UI = gdb
+DEBUG_UI = insight
+
+# Set the debugging back-end to either avarice, simulavr.
+DEBUG_BACKEND = avarice
+#DEBUG_BACKEND = simulavr
+
+# GDB Init Filename.
+GDBINIT_FILE = __avr_gdbinit
+
+# When using avarice settings for the JTAG
+JTAG_DEV = /dev/com1
+
+# Debugging port used to communicate between GDB / avarice / simulavr.
+DEBUG_PORT = 4242
+
+# Debugging host used to communicate between GDB / avarice / simulavr, normally
+#     just set to localhost unless doing some sort of crazy debugging when 
+#     avarice is running on a different computer.
+DEBUG_HOST = localhost
+
+
+
+#============================================================================
+
+
+# Define programs and commands.
+SHELL = sh
+CC = avr-gcc
+OBJCOPY = avr-objcopy
+OBJDUMP = avr-objdump
+SIZE = avr-size
+AR = avr-ar rcs
+NM = avr-nm
+AVRDUDE = avrdude
+REMOVE = rm -f
+REMOVEDIR = rm -rf
+COPY = cp
+WINSHELL = cmd
+
+
+# Define Messages
+# English
+MSG_ERRORS_NONE = Errors: none
+MSG_BEGIN = -------- begin --------
+MSG_END = --------  end  --------
+MSG_SIZE_BEFORE = Size before: 
+MSG_SIZE_AFTER = Size after:
+MSG_COFF = Converting to AVR COFF:
+MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
+MSG_FLASH = Creating load file for Flash:
+MSG_EEPROM = Creating load file for EEPROM:
+MSG_EXTENDED_LISTING = Creating Extended Listing:
+MSG_SYMBOL_TABLE = Creating Symbol Table:
+MSG_LINKING = Linking:
+MSG_COMPILING = Compiling C:
+MSG_COMPILING_CPP = Compiling C++:
+MSG_ASSEMBLING = Assembling:
+MSG_CLEANING = Cleaning project:
+MSG_CREATING_LIBRARY = Creating library:
+
+
+
+
+# Define all object files.
+OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o) 
+
+# Define all listing files.
+LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst) 
+
+
+# Compiler flags to generate dependency files.
+GENDEPFLAGS = -MMD -MP -MF $(DEPDIR)/$(@F).d
+
+
+# Combine all necessary flags and optional flags.
+# Add target processor to flags.
+ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
+ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
+ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
+
+
+
+
+
+# Default target.
+all: begin gccversion sizebefore build sizeafter end
+
+# Change the build target to build a HEX file or a library.
+build: elf hex eep lss sym
+#build: lib
+
+
+elf: $(TARGET).elf
+hex: $(TARGET).hex
+eep: $(TARGET).eep
+lss: $(TARGET).lss
+sym: $(TARGET).sym
+LIBNAME=lib$(TARGET).a
+lib: $(LIBNAME)
+
+
+
+# Eye candy.
+# AVR Studio 3.x does not check make's exit code but relies on
+# the following magic strings to be generated by the compile job.
+begin:
+	@echo
+	@echo $(MSG_BEGIN)
+
+end:
+	@echo $(MSG_END)
+	@echo
+
+
+# Display size of file.
+HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
+ELFSIZE = $(SIZE) --mcu=$(MCU) --format=avr $(TARGET).elf
+
+sizebefore:
+	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
+	2>/dev/null; echo; fi
+
+sizeafter:
+	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
+	2>/dev/null; echo; fi
+
+
+
+# Display compiler version information.
+gccversion : 
+	@$(CC) --version
+
+
+
+# Program the device.  
+program: $(TARGET).hex $(TARGET).eep
+	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
+
+
+# Generate avr-gdb config/init file which does the following:
+#     define the reset signal, load the target file, connect to target, and set 
+#     a breakpoint at main().
+gdb-config: 
+	@$(REMOVE) $(GDBINIT_FILE)
+	@echo define reset >> $(GDBINIT_FILE)
+	@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
+	@echo end >> $(GDBINIT_FILE)
+	@echo file $(TARGET).elf >> $(GDBINIT_FILE)
+	@echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
+ifeq ($(DEBUG_BACKEND),simulavr)
+	@echo load  >> $(GDBINIT_FILE)
+endif
+	@echo break main >> $(GDBINIT_FILE)
+
+debug: gdb-config $(TARGET).elf
+ifeq ($(DEBUG_BACKEND), avarice)
+	@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
+	@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
+	$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
+	@$(WINSHELL) /c pause
+
+else
+	@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
+	$(DEBUG_MFREQ) --port $(DEBUG_PORT)
+endif
+	@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
+
+
+
+
+# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
+COFFCONVERT = $(OBJCOPY) --debugging
+COFFCONVERT += --change-section-address .data-0x800000
+COFFCONVERT += --change-section-address .bss-0x800000
+COFFCONVERT += --change-section-address .noinit-0x800000
+COFFCONVERT += --change-section-address .eeprom-0x810000
+
+
+
+coff: $(TARGET).elf
+	@echo
+	@echo $(MSG_COFF) $(TARGET).cof
+	$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
+
+
+extcoff: $(TARGET).elf
+	@echo
+	@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
+	$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
+
+
+
+# Create final output files (.hex, .eep) from ELF output file.
+%.hex: %.elf
+	@echo
+	@echo $(MSG_FLASH) $@
+	$(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock -R .signature $< $@
+
+%.eep: %.elf
+	@echo
+	@echo $(MSG_EEPROM) $@
+	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
+	--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
+
+# Create extended listing file from ELF output file.
+%.lss: %.elf
+	@echo
+	@echo $(MSG_EXTENDED_LISTING) $@
+	$(OBJDUMP) -h -S -z $< > $@
+
+# Create a symbol table from ELF output file.
+%.sym: %.elf
+	@echo
+	@echo $(MSG_SYMBOL_TABLE) $@
+	$(NM) -n $< > $@
+
+
+
+# Create library from object files.
+.SECONDARY : $(TARGET).a
+.PRECIOUS : $(OBJ)
+%.a: $(OBJ)
+	@echo
+	@echo $(MSG_CREATING_LIBRARY) $@
+	$(AR) $@ $(OBJ)
+
+
+# Link: create ELF output file from object files.
+.SECONDARY : $(TARGET).elf
+.PRECIOUS : $(OBJ)
+%.elf: $(OBJ)
+	@echo
+	@echo $(MSG_LINKING) $@
+	$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
+
+
+# Compile: create object files from C source files.
+$(OBJDIR)/%.o : %.c
+	@echo
+	@echo $(MSG_COMPILING) $<
+	$(CC) -c $(ALL_CFLAGS) $< -o $@ 
+
+
+# Compile: create object files from C++ source files.
+$(OBJDIR)/%.o : %.cpp
+	@echo
+	@echo $(MSG_COMPILING_CPP) $<
+	$(CC) -c $(ALL_CPPFLAGS) $< -o $@ 
+
+
+# Compile: create assembler files from C source files.
+%.s : %.c
+	$(CC) -S $(ALL_CFLAGS) $< -o $@
+
+
+# Compile: create assembler files from C++ source files.
+%.s : %.cpp
+	$(CC) -S $(ALL_CPPFLAGS) $< -o $@
+
+
+# Assemble: create object files from assembler source files.
+$(OBJDIR)/%.o : %.S
+	@echo
+	@echo $(MSG_ASSEMBLING) $<
+	$(CC) -c $(ALL_ASFLAGS) $< -o $@
+
+
+# Create preprocessed source for use in sending a bug report.
+%.i : %.c
+	$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@ 
+
+
+# Target: clean project.
+clean: begin clean_list end
+
+clean_list :
+	@echo
+	@echo $(MSG_CLEANING)
+	$(REMOVE) $(TARGET).hex
+	$(REMOVE) $(TARGET).eep
+	$(REMOVE) $(TARGET).cof
+	$(REMOVE) $(TARGET).elf
+	$(REMOVE) $(TARGET).map
+	$(REMOVE) $(TARGET).sym
+	$(REMOVE) $(TARGET).lss
+	$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
+	$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
+	$(REMOVE) $(SRC:.c=.s)
+	$(REMOVE) $(SRC:.c=.d)
+	$(REMOVE) $(SRC:.c=.i)
+	$(REMOVEDIR) $(DEPDIR)
+	$(REMOVEDIR) $(OBJDIR)
+
+
+# Create object files directory
+$(shell mkdir -p $(OBJDIR) 2>/dev/null)
+$(shell mkdir -p $(OBJDIR)/src 2>/dev/null) # TODO not nice
+$(shell mkdir -p $(OBJDIR)/v-usb/usbdrv 2>/dev/null) # TODO not nice
+
+
+# Include the dependency files.
+-include $(shell mkdir $(DEPDIR) 2>/dev/null) $(wildcard $(DEPDIR)/*)
+
+
+# Listing of phony targets.
+.PHONY : all begin finish end sizebefore sizeafter gccversion \
+build elf hex eep lss sym coff extcoff \
+clean clean_list program debug gdb-config

sensor/include/usbconfig.h

@@ -0,0 +1,386 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ */
+
+#ifndef __usbconfig_h_included__
+#define __usbconfig_h_included__
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
++ To create your own usbconfig.h file, copy this file to your project's
++ firmware source directory) and rename it to "usbconfig.h".
++ Then edit it accordingly.
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME      B
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      4
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       3
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    0
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   0
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER              3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      10
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER           100
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      0
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS          0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF                   0
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define  USB_CFG_VENDOR_ID       0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define  USB_CFG_DEVICE_ID       0xdc, 0x05 /* = 0x05dc = 1500 */
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION  0x00, 0x01
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'o', 'b', 'd', 'e', 'v', '.', 'a', 't'
+#define USB_CFG_VENDOR_NAME_LEN 8
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'T', 'e', 'm', 'p', 'l', 'a', 't', 'e'
+#define USB_CFG_DEVICE_NAME_LEN 8
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS        0xff    /* set to 0 if deferred to interface */
+#define USB_CFG_DEVICE_SUBCLASS     0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS     0   /* define class here if not at device level */
+#define USB_CFG_INTERFACE_SUBCLASS  0
+#define USB_CFG_INTERFACE_PROTOCOL  0
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+/* #define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    42 */
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+
+//#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We may define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+
+// https://github.com/micronucleus/micronucleus/blob/master/firmware/configuration/t85_default/bootloaderconfig.h
+// setup interrupt for Pin Change for D+
+#define USB_INTR_CFG            PCMSK // Pin interrupt enable register
+#define USB_INTR_CFG_SET        (1 << USB_CFG_DPLUS_BIT) // Mask for pin in pin interrupt enable register PCMSK to be set on usbInit
+#define USB_INTR_CFG_CLR        0 // Mask for pin in pin interrupt enable register PCMSK to be cleared on usbInit. 0 = no clear
+#define USB_INTR_ENABLE         GIMSK // Global interrupt enable register
+#define USB_INTR_ENABLE_BIT     PCIE  // Bit position in global interrupt enable register
+#define USB_INTR_PENDING        GIFR  // Register to read interrupt flag
+#define USB_INTR_PENDING_BIT    PCIF  // Bit position in register to read interrupt flag
+
+#endif /* __usbconfig_h_included__ */

sensor/src/main.c

@@ -0,0 +1,30 @@
+
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <avr/wdt.h>
+#include <util/delay.h>
+
+#include "usbdrv.h"
+
+usbMsgLen_t usbFunctionSetup(uchar data[8])
+{
+    return 0;   /* default for not implemented requests: return no data back to host */
+}
+
+int __attribute__((noreturn)) main(void) {
+    wdt_enable(WDTO_1S);
+
+    usbInit();
+
+    usbDeviceDisconnect();  /* enforce re-enumeration, do this while interrupts are disabled! */
+    wdt_reset();
+    _delay_ms(255); /* fake USB disconnect for > 250 ms */
+    usbDeviceConnect();
+
+    sei();
+
+    while (1) {
+        wdt_reset();
+        usbPoll();
+    }
+}

sensor/v-usb

@@ -0,0 +1 @@
+Subproject commit 7a28fdc685952412dad2b8842429127bc1cf9fa7