Arduino RFID door lock with UART RFID antenna
Du kannst nicht mehr als 25 Themen auswählen Themen müssen mit entweder einem Buchstaben oder einer Ziffer beginnen. Sie können Bindestriche („-“) enthalten und bis zu 35 Zeichen lang sein.

RFID-Door.ino 3.5KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113
  1. /*
  2. Very simple RFID Door Opener
  3. Input: RFID Antenna, outputs TLL UART level, 9600 8N1, 5bytes ID in binary
  4. Input: pushbutton to activate output
  5. Output: Relais connected to Solenoid controlling door lock
  6. */
  7. #include <SoftwareSerial.h>
  8. #define DOOR_OPEN LOW /* when correct id transmitted */
  9. #define DOOR_CLOSED HIGH /* idle or after timeout */
  10. #define DOOR_OPEN_TIME (2 * 1000) /* how long to keep door open with rfid tag */
  11. #define DOOR_OPEN_TIME_MANUAL (1 * 1000) /* how long to keep door open with button */
  12. #define BUFFER_CLEAR_TIME 250 /* bigger than time between serial input characters */
  13. #define ID_LENGTH 5 /* length of ID to read and compare */
  14. #define BUFFER_LEN (2 * ID_LENGTH) /* slightly longer than ID, just in case */
  15. // pin assignments
  16. static const int rfid_rx = 5;
  17. static const int door_out = 6;
  18. static const int button_in = 7;
  19. // known RFID ID codes
  20. static const unsigned char known_codes[][ID_LENGTH] = {
  21. { 0x00, 0x00, 0x00, 0x00, 0x00 },
  22. { 0x00, 0x00, 0x00, 0x00, 0x00 }
  23. };
  24. unsigned char read_buffer[BUFFER_LEN];
  25. int buffer_pos = 0;
  26. unsigned long door_time = 0;
  27. unsigned long manual_time = 0;
  28. unsigned long buffer_time = 0;
  29. SoftwareSerial rfid_serial(rfid_rx, LED_BUILTIN);
  30. void setup() {
  31. pinMode(rfid_rx, INPUT);
  32. pinMode(button_in, INPUT);
  33. pinMode(door_out, OUTPUT);
  34. digitalWrite(door_out, DOOR_CLOSED);
  35. digitalWrite(button_in, HIGH); // enable pull-up
  36. rfid_serial.begin(9600);
  37. rfid_serial.println("RFID Door initialized");
  38. Serial.begin(115200);
  39. Serial.println("RFID Door initialized");
  40. }
  41. void loop() {
  42. // read from RFID antenna
  43. if (rfid_serial.available()) {
  44. unsigned char one = rfid_serial.read();
  45. read_buffer[buffer_pos] = one;
  46. if (buffer_pos < (BUFFER_LEN - 1)) {
  47. buffer_pos++;
  48. } else {
  49. buffer_pos = 0; // reset on overflow
  50. return;
  51. }
  52. // dump to USB so we can add new codes later if we need to
  53. Serial.print("Got byte: ");
  54. Serial.println(one, HEX);
  55. // store time of last received byte
  56. buffer_time = millis();
  57. // check for matching ID
  58. if (buffer_pos >= ID_LENGTH) {
  59. for (int o = 0; o < (buffer_pos - ID_LENGTH); o++) {
  60. for (int c = 0; c < (sizeof(known_codes) / sizeof(known_codes[0])); c++) {
  61. int match = 1;
  62. for (int i = 0; i < ID_LENGTH; i++) {
  63. if (read_buffer[o + i] != known_codes[c][i]) {
  64. match = 0;
  65. break;
  66. }
  67. }
  68. if (match) {
  69. digitalWrite(door_out, DOOR_OPEN);
  70. door_time = millis();
  71. buffer_pos = 0;
  72. buffer_time = 0;
  73. return;
  74. }
  75. }
  76. }
  77. }
  78. }
  79. if (digitalRead(button_in) == LOW) {
  80. digitalWrite(door_out, DOOR_OPEN);
  81. manual_time = millis();
  82. door_time = 0;
  83. }
  84. // if enough time without data, clear buffer
  85. if ((buffer_time != 0) && ((millis() - buffer_time) >= BUFFER_CLEAR_TIME)) {
  86. buffer_pos = 0;
  87. buffer_time = 0;
  88. }
  89. // if enough time since door opened, close it
  90. if (((door_time != 0) && ((millis() - door_time) >= DOOR_OPEN_TIME))
  91. || ((manual_time != 0) && ((millis() - manual_time) >= DOOR_OPEN_TIME_MANUAL))) {
  92. digitalWrite(door_out, DOOR_CLOSED);
  93. door_time = 0;
  94. manual_time = 0;
  95. }
  96. }