Replace PLA/ABS preheating with generic

Marlin/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/Marlin_main.cpp

@@ -4908,32 +4908,32 @@ inline void gcode_M140() {
         case 0:
           if (code_seen('H')) {
             v = code_value_int();
-            plaPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            preheatHotendTemp1 = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
           }
           if (code_seen('F')) {
             v = code_value_int();
-            plaPreheatFanSpeed = constrain(v, 0, 255);
+            preheatFanSpeed1 = constrain(v, 0, 255);
           }
           #if TEMP_SENSOR_BED != 0
             if (code_seen('B')) {
               v = code_value_int();
-              plaPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
+              preheatBedTemp1 = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
             }
           #endif
           break;
         case 1:
           if (code_seen('H')) {
             v = code_value_int();
-            absPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            preheatHotendTemp2 = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
           }
           if (code_seen('F')) {
             v = code_value_int();
-            absPreheatFanSpeed = constrain(v, 0, 255);
+            preheatFanSpeed2 = constrain(v, 0, 255);
           }
           #if TEMP_SENSOR_BED != 0
             if (code_seen('B')) {
               v = code_value_int();
-              absPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
+              preheatBedTemp2 = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
             }
           #endif
           break;

Marlin/SanityCheck.h

@@ -644,6 +644,18 @@
   #error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
 #elif ENABLED(FILAMENTCHANGEENABLE)
   #error "FILAMENTCHANGEENABLE is now FILAMENT_CHANGE_FEATURE. Please update your configuration."
+#elif defined(PLA_PREHEAT_HOTEND_TEMP)
+  #error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
+#elif defined(PLA_PREHEAT_HPB_TEMP)
+  #error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
+#elif defined(PLA_PREHEAT_FAN_SPEED)
+  #error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
+#elif defined(ABS_PREHEAT_HOTEND_TEMP)
+  #error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
+#elif defined(ABS_PREHEAT_HPB_TEMP)
+  #error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
+#elif defined(ABS_PREHEAT_FAN_SPEED)
+  #error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
 #endif
 
 #endif //SANITYCHECK_H

Marlin/configuration_store.cpp

@@ -85,12 +85,12 @@
  *  285  M666 Z    z_endstop_adj (float)
  *
  * ULTIPANEL:
- *  289  M145 S0 H plaPreheatHotendTemp (int)
- *  291  M145 S0 B plaPreheatHPBTemp (int)
- *  293  M145 S0 F plaPreheatFanSpeed (int)
- *  295  M145 S1 H absPreheatHotendTemp (int)
- *  297  M145 S1 B absPreheatHPBTemp (int)
- *  299  M145 S1 F absPreheatFanSpeed (int)
+ *  289  M145 S0 H preheatHotendTemp1 (int)
+ *  291  M145 S0 B preheatBedTemp1 (int)
+ *  293  M145 S0 F preheatFanSpeed1 (int)
+ *  295  M145 S1 H preheatHotendTemp2 (int)
+ *  297  M145 S1 B preheatBedTemp2 (int)
+ *  299  M145 S1 F preheatFanSpeed2 (int)
  *
  * PIDTEMP:
  *  301  M301 E0 PIDC  Kp[0], Ki[0], Kd[0], Kc[0] (float x4)
@@ -262,16 +262,16 @@ void Config_StoreSettings()  {
   #endif
 
   #if DISABLED(ULTIPANEL)
-    int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
-        absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
+    int preheatHotendTemp1 = PREHEAT_1_TEMP_HOTEND, preheatBedTemp1 = PREHEAT_1_TEMP_BED, preheatFanSpeed1 = PREHEAT_1_FAN_SPEED,
+        preheatHotendTemp2 = PREHEAT_2_TEMP_HOTEND, preheatBedTemp2 = PREHEAT_2_TEMP_BED, preheatFanSpeed2 = PREHEAT_2_FAN_SPEED;
   #endif // !ULTIPANEL
 
-  EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
-  EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
-  EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
-  EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
-  EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
-  EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
+  EEPROM_WRITE_VAR(i, preheatHotendTemp1);
+  EEPROM_WRITE_VAR(i, preheatBedTemp1);
+  EEPROM_WRITE_VAR(i, preheatFanSpeed1);
+  EEPROM_WRITE_VAR(i, preheatHotendTemp2);
+  EEPROM_WRITE_VAR(i, preheatBedTemp2);
+  EEPROM_WRITE_VAR(i, preheatFanSpeed2);
 
   for (uint8_t e = 0; e < MAX_EXTRUDERS; e++) {
 
@@ -447,16 +447,16 @@ void Config_RetrieveSettings() {
     #endif
 
     #if DISABLED(ULTIPANEL)
-      int plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed,
-          absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed;
+      int preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1,
+          preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2;
     #endif
 
-    EEPROM_READ_VAR(i, plaPreheatHotendTemp);
-    EEPROM_READ_VAR(i, plaPreheatHPBTemp);
-    EEPROM_READ_VAR(i, plaPreheatFanSpeed);
-    EEPROM_READ_VAR(i, absPreheatHotendTemp);
-    EEPROM_READ_VAR(i, absPreheatHPBTemp);
-    EEPROM_READ_VAR(i, absPreheatFanSpeed);
+    EEPROM_READ_VAR(i, preheatHotendTemp1);
+    EEPROM_READ_VAR(i, preheatBedTemp1);
+    EEPROM_READ_VAR(i, preheatFanSpeed1);
+    EEPROM_READ_VAR(i, preheatHotendTemp2);
+    EEPROM_READ_VAR(i, preheatBedTemp2);
+    EEPROM_READ_VAR(i, preheatFanSpeed2);
 
     #if ENABLED(PIDTEMP)
       for (uint8_t e = 0; e < MAX_EXTRUDERS; e++) {
@@ -604,12 +604,12 @@ void Config_ResetDefault() {
   #endif
 
   #if ENABLED(ULTIPANEL)
-    plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP;
-    plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP;
-    plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
-    absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP;
-    absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP;
-    absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
+    preheatHotendTemp1 = PREHEAT_1_TEMP_HOTEND;
+    preheatBedTemp1 = PREHEAT_1_TEMP_BED;
+    preheatFanSpeed1 = PREHEAT_1_FAN_SPEED;
+    preheatHotendTemp2 = PREHEAT_2_TEMP_HOTEND;
+    preheatBedTemp2 = PREHEAT_2_TEMP_BED;
+    preheatFanSpeed2 = PREHEAT_2_FAN_SPEED;
   #endif
 
   #if HAS_LCD_CONTRAST
@@ -814,14 +814,14 @@ void Config_PrintSettings(bool forReplay) {
       SERIAL_ECHOLNPGM("Material heatup parameters:");
       CONFIG_ECHO_START;
     }
-    SERIAL_ECHOPAIR("  M145 S0 H", plaPreheatHotendTemp);
-    SERIAL_ECHOPAIR(" B", plaPreheatHPBTemp);
-    SERIAL_ECHOPAIR(" F", plaPreheatFanSpeed);
+    SERIAL_ECHOPAIR("  M145 S0 H", preheatHotendTemp1);
+    SERIAL_ECHOPAIR(" B", preheatBedTemp1);
+    SERIAL_ECHOPAIR(" F", preheatFanSpeed1);
     SERIAL_EOL;
     CONFIG_ECHO_START;
-    SERIAL_ECHOPAIR("  M145 S1 H", absPreheatHotendTemp);
-    SERIAL_ECHOPAIR(" B", absPreheatHPBTemp);
-    SERIAL_ECHOPAIR(" F", absPreheatFanSpeed);
+    SERIAL_ECHOPAIR("  M145 S1 H", preheatHotendTemp2);
+    SERIAL_ECHOPAIR(" B", preheatBedTemp2);
+    SERIAL_ECHOPAIR(" F", preheatFanSpeed2);
     SERIAL_EOL;
   #endif // ULTIPANEL
 

Marlin/example_configurations/Cartesio/Configuration.h

@@ -777,13 +777,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 190
-#define PLA_PREHEAT_HPB_TEMP 50
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 190
+#define PREHEAT_1_TEMP_BED     50
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Felix/Configuration.h

@@ -761,13 +761,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -759,13 +759,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Hephestos/Configuration.h

@@ -770,13 +770,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 200
-#define PLA_PREHEAT_HPB_TEMP 0
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 200
+#define PREHEAT_1_TEMP_BED      0
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 220
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 220
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -772,13 +772,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP    70
-#define PLA_PREHEAT_FAN_SPEED   0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 210
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP    110
-#define ABS_PREHEAT_FAN_SPEED   0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/K8200/Configuration.h

@@ -795,13 +795,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 190
-#define PLA_PREHEAT_HPB_TEMP 50 // K8200: set back to 70 if you have an upgraded heatbed power supply
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 190
+#define PREHEAT_1_TEMP_BED     50 // K8200: set back to 70 if you have an upgraded heatbed power supply
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 60 // K8200: set back to 110 if you have an upgraded heatbed power supply
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     60 // K8200: set back to 110 if you have an upgraded heatbed power supply
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/K8400/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP 0
-#define PLA_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 210
+#define PREHEAT_1_TEMP_BED      0
+#define PREHEAT_1_FAN_SPEED   165 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 245
-#define ABS_PREHEAT_HPB_TEMP 0
-#define ABS_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 245
+#define PREHEAT_2_TEMP_BED      0
+#define PREHEAT_2_FAN_SPEED   165 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/K8400/Dual Heads/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP 0
-#define PLA_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 210
+#define PREHEAT_1_TEMP_BED      0
+#define PREHEAT_1_FAN_SPEED   165 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 245
-#define ABS_PREHEAT_HPB_TEMP 0
-#define ABS_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 245
+#define PREHEAT_2_TEMP_BED      0
+#define PREHEAT_2_FAN_SPEED   165 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/RigidBot/Configuration.h

@@ -776,13 +776,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/SCARA/Configuration.h

@@ -786,13 +786,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/TAZ4/Configuration.h

@@ -799,13 +799,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 230
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 230
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/WITBOX/Configuration.h

@@ -770,13 +770,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 200
-#define PLA_PREHEAT_HPB_TEMP 0
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 200
+#define PREHEAT_1_TEMP_BED      0
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 220
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 220
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -873,13 +873,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/delta/generic/Configuration.h

@@ -867,13 +867,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -870,13 +870,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -870,13 +870,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -872,13 +872,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/makibox/Configuration.h

@@ -781,13 +781,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -772,13 +772,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/language_an.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Set home offsets"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Establir zero"
-#define MSG_PREHEAT_PLA                     "Precalentar PLA"
-#define MSG_PREHEAT_PLA_N                   "Precalentar PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Precalentar PLA a"
-#define MSG_PREHEAT_PLA_BEDONLY             "Prec. PLA Base"
-#define MSG_PREHEAT_PLA_SETTINGS            "Achustar tem. PLA"
-#define MSG_PREHEAT_ABS                     "Precalentar ABS"
-#define MSG_PREHEAT_ABS_N                   "Precalentar ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Precalentar ABS a"
-#define MSG_PREHEAT_ABS_BEDONLY             "Prec. ABS Base"
-#define MSG_PREHEAT_ABS_SETTINGS            "Achustar tem. ABS"
+#define MSG_PREHEAT_1                       "Precalentar PLA"
+#define MSG_PREHEAT_1_N                     "Precalentar PLA "
+#define MSG_PREHEAT_1_ALL                   "Precalentar PLA a"
+#define MSG_PREHEAT_1_BEDONLY               "Prec. PLA Base"
+#define MSG_PREHEAT_1_SETTINGS              "Achustar tem. PLA"
+#define MSG_PREHEAT_2                       "Precalentar ABS"
+#define MSG_PREHEAT_2_N                     "Precalentar ABS "
+#define MSG_PREHEAT_2_ALL                   "Precalentar ABS a"
+#define MSG_PREHEAT_2_BEDONLY               "Prec. ABS Base"
+#define MSG_PREHEAT_2_SETTINGS              "Achustar tem. ABS"
 #define MSG_COOLDOWN                        "Enfriar"
 #define MSG_SWITCH_PS_ON                    "Enchegar Fuent"
 #define MSG_SWITCH_PS_OFF                   "Desenchegar Fuent"

Marlin/language_bg.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Задай Начало"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Изходна точка"
-#define MSG_PREHEAT_PLA                     "Подгряване PLA"
-#define MSG_PREHEAT_PLA_N                   "Подгряване PLA"
-#define MSG_PREHEAT_PLA_ALL                 "Подгр. PLA Всички"
-#define MSG_PREHEAT_PLA_BEDONLY             "Подгр. PLA Легло"
-#define MSG_PREHEAT_PLA_SETTINGS            "Настройки PLA"
-#define MSG_PREHEAT_ABS                     "Подгряване ABS"
-#define MSG_PREHEAT_ABS_N                   "Подгряване ABS"
-#define MSG_PREHEAT_ABS_ALL                 "Подгр. ABS Всички"
-#define MSG_PREHEAT_ABS_BEDONLY             "Подгр. ABS Легло"
-#define MSG_PREHEAT_ABS_SETTINGS            "Настройки ABS"
+#define MSG_PREHEAT_1                       "Подгряване PLA"
+#define MSG_PREHEAT_1_N                     "Подгряване PLA"
+#define MSG_PREHEAT_1_ALL                   "Подгр. PLA Всички"
+#define MSG_PREHEAT_1_BEDONLY               "Подгр. PLA Легло"
+#define MSG_PREHEAT_1_SETTINGS              "Настройки PLA"
+#define MSG_PREHEAT_2                       "Подгряване ABS"
+#define MSG_PREHEAT_2_N                     "Подгряване ABS"
+#define MSG_PREHEAT_2_ALL                   "Подгр. ABS Всички"
+#define MSG_PREHEAT_2_BEDONLY               "Подгр. ABS Легло"
+#define MSG_PREHEAT_2_SETTINGS              "Настройки ABS"
 #define MSG_COOLDOWN                        "Охлаждане"
 #define MSG_SWITCH_PS_ON                    "Вкл. захранване"
 #define MSG_SWITCH_PS_OFF                   "Изкл. захранване"

Marlin/language_ca.h

@@ -50,16 +50,16 @@
 #define MSG_SET_HOME_OFFSETS                "Set home offsets"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Establir origen"
-#define MSG_PREHEAT_PLA                     "Preescalfar PLA"
-#define MSG_PREHEAT_PLA_N                   "Preescalfar PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Preesc. tot PLA"
-#define MSG_PREHEAT_PLA_BEDONLY             "Preesc. llit PLA"
-#define MSG_PREHEAT_PLA_SETTINGS            "Configuració PLA"
-#define MSG_PREHEAT_ABS                     "Preescalfar ABS"
-#define MSG_PREHEAT_ABS_N                   "Preescalfar ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Preesc. tot ABS"
-#define MSG_PREHEAT_ABS_BEDONLY             "Preesc. llit ABS"
-#define MSG_PREHEAT_ABS_SETTINGS            "Configuració ABS"
+#define MSG_PREHEAT_1                       "Preescalfar PLA"
+#define MSG_PREHEAT_1_N                     "Preescalfar PLA "
+#define MSG_PREHEAT_1_ALL                   "Preesc. tot PLA"
+#define MSG_PREHEAT_1_BEDONLY               "Preesc. llit PLA"
+#define MSG_PREHEAT_1_SETTINGS              "Configuració PLA"
+#define MSG_PREHEAT_2                       "Preescalfar ABS"
+#define MSG_PREHEAT_2_N                     "Preescalfar ABS "
+#define MSG_PREHEAT_2_ALL                   "Preesc. tot ABS"
+#define MSG_PREHEAT_2_BEDONLY               "Preesc. llit ABS"
+#define MSG_PREHEAT_2_SETTINGS              "Configuració ABS"
 #define MSG_COOLDOWN                        "Refredar"
 #define MSG_SWITCH_PS_ON                    "Switch power on"
 #define MSG_SWITCH_PS_OFF                   "Switch power off"

Marlin/language_cn.h

@@ -47,16 +47,16 @@
 #define MSG_SET_HOME_OFFSETS                "\xbe\xbf\xbb\xbc\xbd\xc0\xc1"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "\xbe\xbf\xbc\xbd"
-#define MSG_PREHEAT_PLA                     "\xc3\xc4 PLA"
-#define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
-#define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA " \xc5\xc6"
-#define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA " \xc4\xc7"
-#define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA " \xbe\xbf"
-#define MSG_PREHEAT_ABS                     "\xc3\xc4 ABS"
-#define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
-#define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS " \xc5\xc6"
-#define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS " \xbe\xc6"
-#define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS " \xbe\xbf"
+#define MSG_PREHEAT_1                       "\xc3\xc4 PLA"
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
+#define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 " \xc5\xc6"
+#define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 " \xc4\xc7"
+#define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 " \xbe\xbf"
+#define MSG_PREHEAT_2                       "\xc3\xc4 ABS"
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
+#define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 " \xc5\xc6"
+#define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 " \xbe\xc6"
+#define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 " \xbe\xbf"
 #define MSG_COOLDOWN                        "\xc8\xc9"
 #define MSG_SWITCH_PS_ON                    "\xb9\xcb\xca\xb3"
 #define MSG_SWITCH_PS_OFF                   "\xb9\xcb\xb5\xb6"

Marlin/language_cz.h

@@ -58,16 +58,16 @@
 #define MSG_SET_HOME_OFFSETS                "Nastavit ofsety"
 #define MSG_HOME_OFFSETS_APPLIED            "Ofsety nastaveny"
 #define MSG_SET_ORIGIN                      "Nastavit pocatek"
-#define MSG_PREHEAT_PLA                     "Zahrat PLA"
-#define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
-#define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA " Vse"
-#define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA " Podloz"
-#define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA " Nast"
-#define MSG_PREHEAT_ABS                     "Zahrat ABS"
-#define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
-#define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS " Vse"
-#define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS " Podloz"
-#define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS " Nast"
+#define MSG_PREHEAT_1                       "Zahrat PLA"
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
+#define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 " Vse"
+#define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 " Podloz"
+#define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 " Nast"
+#define MSG_PREHEAT_2                       "Zahrat ABS"
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
+#define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 " Vse"
+#define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 " Podloz"
+#define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 " Nast"
 #define MSG_H1                              "1"
 #define MSG_H2                              "2"
 #define MSG_H3                              "3"

Marlin/language_da.h

@@ -54,16 +54,16 @@
 #define MSG_SET_HOME_OFFSETS                "Sæt forskyding af home"
 #define MSG_HOME_OFFSETS_APPLIED            "Forskydninger af home pos. er tilføjet"
 #define MSG_SET_ORIGIN                      "Sæt origin"
-#define MSG_PREHEAT_PLA                     "Forvarm PLA"
-#define MSG_PREHEAT_PLA_N                   "Forvarm PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Forvarm PLA Alle"
-#define MSG_PREHEAT_PLA_BEDONLY             "Forvarm PLA Bed"
-#define MSG_PREHEAT_PLA_SETTINGS            "Forvarm PLA conf"
-#define MSG_PREHEAT_ABS                     "Forvarm ABS"
-#define MSG_PREHEAT_ABS_N                   "Forvarm ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Forvarm ABS Alle"
-#define MSG_PREHEAT_ABS_BEDONLY             "Forvarm ABS Bed"
-#define MSG_PREHEAT_ABS_SETTINGS            "Forvarm ABS conf"
+#define MSG_PREHEAT_1                       "Forvarm PLA"
+#define MSG_PREHEAT_1_N                     "Forvarm PLA "
+#define MSG_PREHEAT_1_ALL                   "Forvarm PLA Alle"
+#define MSG_PREHEAT_1_BEDONLY               "Forvarm PLA Bed"
+#define MSG_PREHEAT_1_SETTINGS              "Forvarm PLA conf"
+#define MSG_PREHEAT_2                       "Forvarm ABS"
+#define MSG_PREHEAT_2_N                     "Forvarm ABS "
+#define MSG_PREHEAT_2_ALL                   "Forvarm ABS Alle"
+#define MSG_PREHEAT_2_BEDONLY               "Forvarm ABS Bed"
+#define MSG_PREHEAT_2_SETTINGS              "Forvarm ABS conf"
 #define MSG_H1                              "1"
 #define MSG_H2                              "2"
 #define MSG_H3                              "3"

Marlin/language_de.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Setze Homeoffsets"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets aktiv"
 #define MSG_SET_ORIGIN                      "Setze Nullpunkt" //"G92 X0 Y0 Z0" commented out in ultralcd.cpp
-#define MSG_PREHEAT_PLA                     "Vorwärmen PLA"
-#define MSG_PREHEAT_PLA_N                   "Vorwärmen PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Vorw. PLA Alle"
-#define MSG_PREHEAT_PLA_BEDONLY             "Vorw. PLA Bett"
-#define MSG_PREHEAT_PLA_SETTINGS            "Vorw. PLA Einst."
-#define MSG_PREHEAT_ABS                     "Vorwärmen ABS"
-#define MSG_PREHEAT_ABS_N                   "Vorwärmen ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Vorw. ABS Alle"
-#define MSG_PREHEAT_ABS_BEDONLY             "Vorw. ABS Bett"
-#define MSG_PREHEAT_ABS_SETTINGS            "Vorw. ABS Einst."
+#define MSG_PREHEAT_1                       "Vorwärmen PLA"
+#define MSG_PREHEAT_1_N                     "Vorwärmen PLA "
+#define MSG_PREHEAT_1_ALL                   "Vorw. PLA Alle"
+#define MSG_PREHEAT_1_BEDONLY               "Vorw. PLA Bett"
+#define MSG_PREHEAT_1_SETTINGS              "Vorw. PLA Einst."
+#define MSG_PREHEAT_2                       "Vorwärmen ABS"
+#define MSG_PREHEAT_2_N                     "Vorwärmen ABS "
+#define MSG_PREHEAT_2_ALL                   "Vorw. ABS Alle"
+#define MSG_PREHEAT_2_BEDONLY               "Vorw. ABS Bett"
+#define MSG_PREHEAT_2_SETTINGS              "Vorw. ABS Einst."
 #define MSG_COOLDOWN                        "Abkühlen"
 #define MSG_SWITCH_PS_ON                    "Netzteil ein"
 #define MSG_SWITCH_PS_OFF                   "Netzteil aus"

Marlin/language_en.h

@@ -97,35 +97,35 @@
 #ifndef MSG_SET_ORIGIN
   #define MSG_SET_ORIGIN                      "Set origin"
 #endif
-#ifndef MSG_PREHEAT_PLA
-  #define MSG_PREHEAT_PLA                     "Preheat PLA"
+#ifndef MSG_PREHEAT_1
+  #define MSG_PREHEAT_1                       "Preheat PLA"
 #endif
-#ifndef MSG_PREHEAT_PLA_N
-  #define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
+#ifndef MSG_PREHEAT_1_N
+  #define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
 #endif
-#ifndef MSG_PREHEAT_PLA_ALL
-  #define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA " All"
+#ifndef MSG_PREHEAT_1_ALL
+  #define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 " All"
 #endif
-#ifndef MSG_PREHEAT_PLA_BEDONLY
-  #define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA " Bed"
+#ifndef MSG_PREHEAT_1_BEDONLY
+  #define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 " Bed"
 #endif
-#ifndef MSG_PREHEAT_PLA_SETTINGS
-  #define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA " conf"
+#ifndef MSG_PREHEAT_1_SETTINGS
+  #define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 " conf"
 #endif
-#ifndef MSG_PREHEAT_ABS
-  #define MSG_PREHEAT_ABS                     "Preheat ABS"
+#ifndef MSG_PREHEAT_2
+  #define MSG_PREHEAT_2                       "Preheat ABS"
 #endif
-#ifndef MSG_PREHEAT_ABS_N
-  #define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
+#ifndef MSG_PREHEAT_2_N
+  #define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
 #endif
-#ifndef MSG_PREHEAT_ABS_ALL
-  #define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS " All"
+#ifndef MSG_PREHEAT_2_ALL
+  #define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 " All"
 #endif
-#ifndef MSG_PREHEAT_ABS_BEDONLY
-  #define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS " Bed"
+#ifndef MSG_PREHEAT_2_BEDONLY
+  #define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 " Bed"
 #endif
-#ifndef MSG_PREHEAT_ABS_SETTINGS
-  #define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS " conf"
+#ifndef MSG_PREHEAT_2_SETTINGS
+  #define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 " conf"
 #endif
 #ifndef MSG_H1
   #define MSG_H1                              "1"

Marlin/language_es.h

@@ -53,16 +53,16 @@
 #define MSG_SET_HOME_OFFSETS                "Ajustar desfases"
 #define MSG_HOME_OFFSETS_APPLIED            "Desfase aplicado"
 #define MSG_SET_ORIGIN                      "Establecer origen"
-#define MSG_PREHEAT_PLA                     "Precalentar PLA"
-#define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
-#define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA "Todo"
-#define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA"Plataforma"
-#define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA "Config"
-#define MSG_PREHEAT_ABS                     "Precalentar ABS"
-#define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
-#define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS "Todo"
-#define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS "Plataforma"
-#define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS "Config"
+#define MSG_PREHEAT_1                       "Precalentar PLA"
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
+#define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 "Todo"
+#define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1"Plataforma"
+#define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 "Config"
+#define MSG_PREHEAT_2                       "Precalentar ABS"
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
+#define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 "Todo"
+#define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 "Plataforma"
+#define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 "Config"
 #define MSG_H1                              "1"
 #define MSG_H2                              "2"
 #define MSG_H3                              "3"

Marlin/language_eu.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Set home offsets"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Hasiera ipini"
-#define MSG_PREHEAT_PLA                     "Aurreberotu PLA"
-#define MSG_PREHEAT_PLA_N                   "Aurreberotu PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Berotu PLA Guztia"
-#define MSG_PREHEAT_PLA_BEDONLY             "Berotu PLA Ohea"
-#define MSG_PREHEAT_PLA_SETTINGS            "Berotu PLA Konfig"
-#define MSG_PREHEAT_ABS                     "Aurreberotu ABS"
-#define MSG_PREHEAT_ABS_N                   "Aurreberotu ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Berotu ABS Guztia"
-#define MSG_PREHEAT_ABS_BEDONLY             "Berotu ABS Ohea"
-#define MSG_PREHEAT_ABS_SETTINGS            "Berotu ABS Konfig"
+#define MSG_PREHEAT_1                       "Aurreberotu PLA"
+#define MSG_PREHEAT_1_N                     "Aurreberotu PLA "
+#define MSG_PREHEAT_1_ALL                   "Berotu PLA Guztia"
+#define MSG_PREHEAT_1_BEDONLY               "Berotu PLA Ohea"
+#define MSG_PREHEAT_1_SETTINGS              "Berotu PLA Konfig"
+#define MSG_PREHEAT_2                       "Aurreberotu ABS"
+#define MSG_PREHEAT_2_N                     "Aurreberotu ABS "
+#define MSG_PREHEAT_2_ALL                   "Berotu ABS Guztia"
+#define MSG_PREHEAT_2_BEDONLY               "Berotu ABS Ohea"
+#define MSG_PREHEAT_2_SETTINGS              "Berotu ABS Konfig"
 #define MSG_COOLDOWN                        "Hoztu"
 #define MSG_SWITCH_PS_ON                    "Energia piztu"
 #define MSG_SWITCH_PS_OFF                   "Energia itzali"

Marlin/language_fi.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Set home offsets"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Aseta origo"
-#define MSG_PREHEAT_PLA                     "Esilämmitä PLA"
-#define MSG_PREHEAT_PLA_N                   "Esilämmitä PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Esilä. PLA Kaikki"
-#define MSG_PREHEAT_PLA_BEDONLY             "Esilä. PLA Alusta"
-#define MSG_PREHEAT_PLA_SETTINGS            "Esilämm. PLA konf"
-#define MSG_PREHEAT_ABS                     "Esilämmitä ABS"
-#define MSG_PREHEAT_ABS_N                   "Esilämmitä ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Esilä. ABS Kaikki"
-#define MSG_PREHEAT_ABS_BEDONLY             "Esilä. ABS Alusta"
-#define MSG_PREHEAT_ABS_SETTINGS            "Esilämm. ABS konf"
+#define MSG_PREHEAT_1                       "Esilämmitä PLA"
+#define MSG_PREHEAT_1_N                     "Esilämmitä PLA "
+#define MSG_PREHEAT_1_ALL                   "Esilä. PLA Kaikki"
+#define MSG_PREHEAT_1_BEDONLY               "Esilä. PLA Alusta"
+#define MSG_PREHEAT_1_SETTINGS              "Esilämm. PLA konf"
+#define MSG_PREHEAT_2                       "Esilämmitä ABS"
+#define MSG_PREHEAT_2_N                     "Esilämmitä ABS "
+#define MSG_PREHEAT_2_ALL                   "Esilä. ABS Kaikki"
+#define MSG_PREHEAT_2_BEDONLY               "Esilä. ABS Alusta"
+#define MSG_PREHEAT_2_SETTINGS              "Esilämm. ABS konf"
 #define MSG_COOLDOWN                        "Jäähdytä"
 #define MSG_SWITCH_PS_ON                    "Virta päälle"
 #define MSG_SWITCH_PS_OFF                   "Virta pois"

Marlin/language_fr.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Regler decal. origine"
 #define MSG_HOME_OFFSETS_APPLIED            "Decalages appliques"
 #define MSG_SET_ORIGIN                      "Regler origine"
-#define MSG_PREHEAT_PLA                     "Prechauffage PLA"
-#define MSG_PREHEAT_PLA_N                   "Prechauff. PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Prech. PLA Tout"
-#define MSG_PREHEAT_PLA_BEDONLY             "Prech. PLA Plateau"
-#define MSG_PREHEAT_PLA_SETTINGS            "Regl. prech. PLA"
-#define MSG_PREHEAT_ABS                     "Prechauffage ABS"
-#define MSG_PREHEAT_ABS_N                   "Prechauff. ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Prech. ABS Tout"
-#define MSG_PREHEAT_ABS_BEDONLY             "Prech. ABS Plateau"
-#define MSG_PREHEAT_ABS_SETTINGS            "Regl. prech. ABS"
+#define MSG_PREHEAT_1                       "Prechauffage PLA"
+#define MSG_PREHEAT_1_N                     "Prechauff. PLA "
+#define MSG_PREHEAT_1_ALL                   "Prech. PLA Tout"
+#define MSG_PREHEAT_1_BEDONLY               "Prech. PLA Plateau"
+#define MSG_PREHEAT_1_SETTINGS              "Regl. prech. PLA"
+#define MSG_PREHEAT_2                       "Prechauffage ABS"
+#define MSG_PREHEAT_2_N                     "Prechauff. ABS "
+#define MSG_PREHEAT_2_ALL                   "Prech. ABS Tout"
+#define MSG_PREHEAT_2_BEDONLY               "Prech. ABS Plateau"
+#define MSG_PREHEAT_2_SETTINGS              "Regl. prech. ABS"
 #define MSG_COOLDOWN                        "Refroidir"
 #define MSG_SWITCH_PS_ON                    "Allumer alim."
 #define MSG_SWITCH_PS_OFF                   "Eteindre alim."

Marlin/language_gl.h

@@ -54,16 +54,16 @@
 #define MSG_SET_HOME_OFFSETS                "Offsets na orixe"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets fixados"
 #define MSG_SET_ORIGIN                      "Fixar orixe"
-#define MSG_PREHEAT_PLA                     "Prequentar PLA"
-#define MSG_PREHEAT_PLA_N                   "Prequentar PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Preque. PLA Todo"
-#define MSG_PREHEAT_PLA_BEDONLY             "Preque. PLA Cama"
-#define MSG_PREHEAT_PLA_SETTINGS            "Preque. PLA conf"
-#define MSG_PREHEAT_ABS                     "Prequentar ABS"
-#define MSG_PREHEAT_ABS_N                   "Prequentar ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Preque. ABS Todo"
-#define MSG_PREHEAT_ABS_BEDONLY             "Preque. ABS Cama"
-#define MSG_PREHEAT_ABS_SETTINGS            "Preque. ABS conf"
+#define MSG_PREHEAT_1                       "Prequentar PLA"
+#define MSG_PREHEAT_1_N                     "Prequentar PLA "
+#define MSG_PREHEAT_1_ALL                   "Preque. PLA Todo"
+#define MSG_PREHEAT_1_BEDONLY               "Preque. PLA Cama"
+#define MSG_PREHEAT_1_SETTINGS              "Preque. PLA conf"
+#define MSG_PREHEAT_2                       "Prequentar ABS"
+#define MSG_PREHEAT_2_N                     "Prequentar ABS "
+#define MSG_PREHEAT_2_ALL                   "Preque. ABS Todo"
+#define MSG_PREHEAT_2_BEDONLY               "Preque. ABS Cama"
+#define MSG_PREHEAT_2_SETTINGS              "Preque. ABS conf"
 #define MSG_H1                              "1"
 #define MSG_H2                              "2"
 #define MSG_H3                              "3"

Marlin/language_hr.h

@@ -55,16 +55,16 @@
 #define MSG_SET_HOME_OFFSETS                "Postavi home offsete"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets postavljeni"
 #define MSG_SET_ORIGIN                      "Postavi ishodište"
-#define MSG_PREHEAT_PLA                     "Predgrij PLA"
-#define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
-#define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA " Sve"
-#define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA " Bed"
-#define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA " conf"
-#define MSG_PREHEAT_ABS                     "Predgrij ABS"
-#define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
-#define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS " Sve"
-#define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS " Bed"
-#define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS " conf"
+#define MSG_PREHEAT_1                       "Predgrij PLA"
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
+#define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 " Sve"
+#define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 " Bed"
+#define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 " conf"
+#define MSG_PREHEAT_2                       "Predgrij ABS"
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
+#define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 " Sve"
+#define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 " Bed"
+#define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 " conf"
 #define MSG_H1                              "1"
 #define MSG_H2                              "2"
 #define MSG_H3                              "3"

Marlin/language_it.h

@@ -54,16 +54,16 @@
 #define MSG_SET_HOME_OFFSETS                "Imp. offset home"
 #define MSG_HOME_OFFSETS_APPLIED            "Offset applicato"
 #define MSG_SET_ORIGIN                      "Imposta Origine"
-#define MSG_PREHEAT_PLA                     "Preriscalda PLA"
-#define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
-#define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA " Tutto"
-#define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA " Piatto"
-#define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA " conf"
-#define MSG_PREHEAT_ABS                     "Preriscalda ABS"
-#define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
-#define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS " Tutto"
-#define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS " Piatto"
-#define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS " conf"
+#define MSG_PREHEAT_1                       "Preriscalda PLA"
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
+#define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 " Tutto"
+#define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 " Piatto"
+#define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 " conf"
+#define MSG_PREHEAT_2                       "Preriscalda ABS"
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
+#define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 " Tutto"
+#define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 " Piatto"
+#define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 " conf"
 #define MSG_COOLDOWN                        "Raffredda"
 #define MSG_SWITCH_PS_ON                    "Accendi aliment."
 #define MSG_SWITCH_PS_OFF                   "Spegni aliment."

Marlin/language_kana.h

@@ -56,16 +56,16 @@
 #define MSG_SET_HOME_OFFSETS                "\xb7\xbc\xde\xad\xdd\xb5\xcc\xbe\xaf\xc4\xbe\xaf\xc3\xb2"         // "ｷｼﾞｭﾝｵﾌｾｯﾄｾｯﾃｲ" ("Set home offsets")
 #define MSG_HOME_OFFSETS_APPLIED            "\xb5\xcc\xbe\xaf\xc4\xb6\xde\xc3\xb7\xd6\xb3\xbb\xda\xcf\xbc\xc0" // "ｵﾌｾｯﾄｶﾞﾃｷﾖｳｻﾚﾏｼﾀ" ("Offsets applied")
 #define MSG_SET_ORIGIN                      "\xb7\xbc\xde\xad\xdd\xbe\xaf\xc4"                                 // "ｷｼﾞｭﾝｾｯﾄ" ("Set origin")
-#define MSG_PREHEAT_PLA                     "PLA \xd6\xc8\xc2"                                                 // "PLA ﾖﾈﾂ" ("Preheat PLA")
-#define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
-#define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA " \xbd\xcd\xde\xc3"                                // " ｽﾍﾞﾃ" (" All")
-#define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA " \xcd\xde\xaf\xc4\xde"                            // " ﾍﾞｯﾄﾞ" (" Bed")
-#define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA " \xbe\xaf\xc3\xb2"                                // " ｾｯﾃｲ" (" conf")
-#define MSG_PREHEAT_ABS                     "ABS \xd6\xc8\xc2"                                                 // "ABS ﾖﾈﾂ" ("Preheat ABS")
-#define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
-#define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS " \xbd\xcd\xde\xc3"                                // " ｽﾍﾞﾃ" (" All")
-#define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS " \xcd\xde\xaf\xc4\xde"                            // " ﾍﾞｯﾄﾞ" (" Bed")
-#define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS " \xbe\xaf\xc3\xb2"                                // " ｾｯﾃｲ" (" conf")
+#define MSG_PREHEAT_1                       "PLA \xd6\xc8\xc2"                                                 // "PLA ﾖﾈﾂ" ("Preheat PLA")
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
+#define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 " \xbd\xcd\xde\xc3"                                // " ｽﾍﾞﾃ" (" All")
+#define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 " \xcd\xde\xaf\xc4\xde"                            // " ﾍﾞｯﾄﾞ" (" Bed")
+#define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 " \xbe\xaf\xc3\xb2"                                // " ｾｯﾃｲ" (" conf")
+#define MSG_PREHEAT_2                       "ABS \xd6\xc8\xc2"                                                 // "ABS ﾖﾈﾂ" ("Preheat ABS")
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
+#define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 " \xbd\xcd\xde\xc3"                                // " ｽﾍﾞﾃ" (" All")
+#define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 " \xcd\xde\xaf\xc4\xde"                            // " ﾍﾞｯﾄﾞ" (" Bed")
+#define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 " \xbe\xaf\xc3\xb2"                                // " ｾｯﾃｲ" (" conf")
 #define MSG_COOLDOWN                        "\xb6\xc8\xc2\xc3\xb2\xbc"                                         // "ｶﾈﾂﾃｲｼ" ("Cooldown")
 #define MSG_SWITCH_PS_ON                    "\xc3\xde\xdd\xb9\xde\xdd\x20\xb5\xdd"                             // "ﾃﾞﾝｹﾞﾝ ｵﾝ" ("Switch power on")
 #define MSG_SWITCH_PS_OFF                   "\xc3\xde\xdd\xb9\xde\xdd\x20\xb5\xcc"                             // "ﾃﾞﾝｹﾞﾝ ｵﾌ" ("Switch power off")

Marlin/language_kana_utf8.h

@@ -59,16 +59,16 @@
 #define MSG_SET_HOME_OFFSETS                "キジュンオフセットセッテイ"         // "Set home offsets"
 #define MSG_HOME_OFFSETS_APPLIED            "オフセットガテキヨウサレマシタ"       // "Offsets applied"
 #define MSG_SET_ORIGIN                      "キジュンセット"                 // "Set origin"
-#define MSG_PREHEAT_PLA                     "PLA ヨネツ"                   // "Preheat PLA"
-#define MSG_PREHEAT_PLA_N                   MSG_PREHEAT_PLA " "
-#define MSG_PREHEAT_PLA_ALL                 MSG_PREHEAT_PLA " スベテ"     // " All"
-#define MSG_PREHEAT_PLA_BEDONLY             MSG_PREHEAT_PLA " ベッド"     // " Bed"
-#define MSG_PREHEAT_PLA_SETTINGS            MSG_PREHEAT_PLA " セッテイ"    // " conf"
-#define MSG_PREHEAT_ABS                     "ABS ヨネツ"                  // "Preheat ABS"
-#define MSG_PREHEAT_ABS_N                   MSG_PREHEAT_ABS " "
-#define MSG_PREHEAT_ABS_ALL                 MSG_PREHEAT_ABS " スベテ"     // " All"
-#define MSG_PREHEAT_ABS_BEDONLY             MSG_PREHEAT_ABS " ベッド"     // " Bed"
-#define MSG_PREHEAT_ABS_SETTINGS            MSG_PREHEAT_ABS " セッテイ"    // " conf"
+#define MSG_PREHEAT_1                       "PLA ヨネツ"                   // "Preheat PLA"
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 " "
+#define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 " スベテ"     // " All"
+#define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 " ベッド"     // " Bed"
+#define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 " セッテイ"    // " conf"
+#define MSG_PREHEAT_2                       "ABS ヨネツ"                  // "Preheat ABS"
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 " "
+#define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 " スベテ"     // " All"
+#define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 " ベッド"     // " Bed"
+#define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 " セッテイ"    // " conf"
 #define MSG_COOLDOWN                        "カネツテイシ"                  // "Cooldown"
 #define MSG_SWITCH_PS_ON                    "デンゲン オン"                 // "Switch power on"
 #define MSG_SWITCH_PS_OFF                   "デンゲン オフ"                 // "Switch power off"

Marlin/language_nl.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Zet home offsets"
 #define MSG_HOME_OFFSETS_APPLIED            "H offset toegep."
 #define MSG_SET_ORIGIN                      "Nulpunt instellen"
-#define MSG_PREHEAT_PLA                     "PLA voorverwarmen"
-#define MSG_PREHEAT_PLA_N                   "PLA voorverw. "
-#define MSG_PREHEAT_PLA_ALL                 "PLA voorverw. aan"
-#define MSG_PREHEAT_PLA_BEDONLY             "PLA voorverw. Bed"
-#define MSG_PREHEAT_PLA_SETTINGS            "PLA verw. conf"
-#define MSG_PREHEAT_ABS                     "ABS voorverwarmen"
-#define MSG_PREHEAT_ABS_N                   "ABS voorverw. "
-#define MSG_PREHEAT_ABS_ALL                 "ABS voorverw. aan"
-#define MSG_PREHEAT_ABS_BEDONLY             "ABS voorverw. Bed"
-#define MSG_PREHEAT_ABS_SETTINGS            "ABS verw. conf"
+#define MSG_PREHEAT_1                       "PLA voorverwarmen"
+#define MSG_PREHEAT_1_N                     "PLA voorverw. "
+#define MSG_PREHEAT_1_ALL                   "PLA voorverw. aan"
+#define MSG_PREHEAT_1_BEDONLY               "PLA voorverw. Bed"
+#define MSG_PREHEAT_1_SETTINGS              "PLA verw. conf"
+#define MSG_PREHEAT_2                       "ABS voorverwarmen"
+#define MSG_PREHEAT_2_N                     "ABS voorverw. "
+#define MSG_PREHEAT_2_ALL                   "ABS voorverw. aan"
+#define MSG_PREHEAT_2_BEDONLY               "ABS voorverw. Bed"
+#define MSG_PREHEAT_2_SETTINGS              "ABS verw. conf"
 #define MSG_COOLDOWN                        "Afkoelen"
 #define MSG_SWITCH_PS_ON                    "Stroom aan"
 #define MSG_SWITCH_PS_OFF                   "Stroom uit"

Marlin/language_pl.h

@@ -51,16 +51,16 @@
 #define MSG_SET_HOME_OFFSETS                "Ust. poz. zer."
 #define MSG_HOME_OFFSETS_APPLIED            "Poz. zerowa ust."
 #define MSG_SET_ORIGIN                      "Ustaw punkt zero"
-#define MSG_PREHEAT_PLA                     "Rozgrzej PLA"
-#define MSG_PREHEAT_PLA_N                   "Rozgrzej PLA "
-#define MSG_PREHEAT_PLA_ALL                 "Roz. PLA Wszystko"
-#define MSG_PREHEAT_PLA_BEDONLY             "Rozgrzej PLA Loze"
-#define MSG_PREHEAT_PLA_SETTINGS            "Ustaw. rozg. PLA"
-#define MSG_PREHEAT_ABS                     "Rozgrzej ABS"
-#define MSG_PREHEAT_ABS_N                   "Rozgrzej ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Roz. ABS Wszystko"
-#define MSG_PREHEAT_ABS_BEDONLY             "Rozgrzej ABS Loze"
-#define MSG_PREHEAT_ABS_SETTINGS            "Ustaw. rozg. ABS"
+#define MSG_PREHEAT_1                       "Rozgrzej PLA"
+#define MSG_PREHEAT_1_N                     "Rozgrzej PLA "
+#define MSG_PREHEAT_1_ALL                   "Roz. PLA Wszystko"
+#define MSG_PREHEAT_1_BEDONLY               "Rozgrzej PLA Loze"
+#define MSG_PREHEAT_1_SETTINGS              "Ustaw. rozg. PLA"
+#define MSG_PREHEAT_2                       "Rozgrzej ABS"
+#define MSG_PREHEAT_2_N                     "Rozgrzej ABS "
+#define MSG_PREHEAT_2_ALL                   "Roz. ABS Wszystko"
+#define MSG_PREHEAT_2_BEDONLY               "Rozgrzej ABS Loze"
+#define MSG_PREHEAT_2_SETTINGS              "Ustaw. rozg. ABS"
 #define MSG_H1                              "1"
 #define MSG_H2                              "2"
 #define MSG_H3                              "3"

Marlin/language_pt-br.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Ajustar Jogo"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Ajustar orig."
-#define MSG_PREHEAT_PLA                     "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_N                   "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_ALL                 "Pre-aq.Todo PLA"
-#define MSG_PREHEAT_PLA_BEDONLY             "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_PLA_SETTINGS            "Ajustar PLA"
-#define MSG_PREHEAT_ABS                     "Pre-aquecer ABS"
-#define MSG_PREHEAT_ABS_N                   "Pre-aquecer ABS"
-#define MSG_PREHEAT_ABS_ALL                 "Pre-aq.Todo ABS"
-#define MSG_PREHEAT_ABS_BEDONLY             "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_ABS_SETTINGS            "Ajustar ABS"
+#define MSG_PREHEAT_1                       "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_N                     "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_ALL                   "Pre-aq.Todo PLA"
+#define MSG_PREHEAT_1_BEDONLY               "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_1_SETTINGS              "Ajustar PLA"
+#define MSG_PREHEAT_2                       "Pre-aquecer ABS"
+#define MSG_PREHEAT_2_N                     "Pre-aquecer ABS"
+#define MSG_PREHEAT_2_ALL                   "Pre-aq.Todo ABS"
+#define MSG_PREHEAT_2_BEDONLY               "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_2_SETTINGS              "Ajustar ABS"
 #define MSG_COOLDOWN                        "Esfriar"
 #define MSG_SWITCH_PS_ON                    "Ligar"
 #define MSG_SWITCH_PS_OFF                   "Desligar"

Marlin/language_pt-br_utf8.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Ajustar Jogo"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Ajustar orig."
-#define MSG_PREHEAT_PLA                     "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_N                   "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_ALL                 "Pre-aq.Todo PLA"
-#define MSG_PREHEAT_PLA_BEDONLY             "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_PLA_SETTINGS            "Ajustar PLA"
-#define MSG_PREHEAT_ABS                     "Pre-aquecer ABS"
-#define MSG_PREHEAT_ABS_N                   "Pre-aquecer ABS"
-#define MSG_PREHEAT_ABS_ALL                 "Pre-aq.Todo ABS"
-#define MSG_PREHEAT_ABS_BEDONLY             "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_ABS_SETTINGS            "Ajustar ABS"
+#define MSG_PREHEAT_1                       "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_N                     "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_ALL                   "Pre-aq.Todo PLA"
+#define MSG_PREHEAT_1_BEDONLY               "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_1_SETTINGS              "Ajustar PLA"
+#define MSG_PREHEAT_2                       "Pre-aquecer ABS"
+#define MSG_PREHEAT_2_N                     "Pre-aquecer ABS"
+#define MSG_PREHEAT_2_ALL                   "Pre-aq.Todo ABS"
+#define MSG_PREHEAT_2_BEDONLY               "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_2_SETTINGS              "Ajustar ABS"
 #define MSG_COOLDOWN                        "Esfriar"
 #define MSG_SWITCH_PS_ON                    "Ligar"
 #define MSG_SWITCH_PS_OFF                   "Desligar"

Marlin/language_pt.h

@@ -53,16 +53,16 @@
 #define MSG_SET_HOME_OFFSETS                "Definir desvio"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Definir origem"
-#define MSG_PREHEAT_PLA                     "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_N                   "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_ALL                 "Pre-aq. PLA Tudo"
-#define MSG_PREHEAT_PLA_BEDONLY             "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_PLA_SETTINGS            "Definicoes PLA"
-#define MSG_PREHEAT_ABS                     "Pre-aquecer ABS"
-#define MSG_PREHEAT_ABS_N                   "Pre-aquecer ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Pre-aq. ABS Tudo"
-#define MSG_PREHEAT_ABS_BEDONLY             "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_ABS_SETTINGS            "Definicoes ABS"
+#define MSG_PREHEAT_1                       "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_N                     "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_ALL                   "Pre-aq. PLA Tudo"
+#define MSG_PREHEAT_1_BEDONLY               "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_1_SETTINGS              "Definicoes PLA"
+#define MSG_PREHEAT_2                       "Pre-aquecer ABS"
+#define MSG_PREHEAT_2_N                     "Pre-aquecer ABS "
+#define MSG_PREHEAT_2_ALL                   "Pre-aq. ABS Tudo"
+#define MSG_PREHEAT_2_BEDONLY               "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_2_SETTINGS              "Definicoes ABS"
 #define MSG_COOLDOWN                        "Arrefecer"
 #define MSG_SWITCH_PS_ON                    "Ligar"
 #define MSG_SWITCH_PS_OFF                   "Desligar"

Marlin/language_pt_utf8.h

@@ -53,16 +53,16 @@
 #define MSG_SET_HOME_OFFSETS                "Definir desvio"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets aplicados"
 #define MSG_SET_ORIGIN                      "Definir origem"
-#define MSG_PREHEAT_PLA                     "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_N                   "Pre-aquecer PLA"
-#define MSG_PREHEAT_PLA_ALL                 "Pre-aq. PLA Tudo"
-#define MSG_PREHEAT_PLA_BEDONLY             "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_PLA_SETTINGS            "Definições PLA"
-#define MSG_PREHEAT_ABS                     "Pre-aquecer ABS"
-#define MSG_PREHEAT_ABS_N                   "Pre-aquecer ABS "
-#define MSG_PREHEAT_ABS_ALL                 "Pre-aq. ABS Tudo"
-#define MSG_PREHEAT_ABS_BEDONLY             "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
-#define MSG_PREHEAT_ABS_SETTINGS            "Definições ABS"
+#define MSG_PREHEAT_1                       "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_N                     "Pre-aquecer PLA"
+#define MSG_PREHEAT_1_ALL                   "Pre-aq. PLA Tudo"
+#define MSG_PREHEAT_1_BEDONLY               "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_1_SETTINGS              "Definições PLA"
+#define MSG_PREHEAT_2                       "Pre-aquecer ABS"
+#define MSG_PREHEAT_2_N                     "Pre-aquecer ABS "
+#define MSG_PREHEAT_2_ALL                   "Pre-aq. ABS Tudo"
+#define MSG_PREHEAT_2_BEDONLY               "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
+#define MSG_PREHEAT_2_SETTINGS              "Definições ABS"
 #define MSG_COOLDOWN                        "Arrefecer"
 #define MSG_SWITCH_PS_ON                    "Ligar"
 #define MSG_SWITCH_PS_OFF                   "Desligar"

Marlin/language_ru.h

@@ -49,16 +49,16 @@
 #define MSG_SET_HOME_OFFSETS                "Запомнить парковку"
 #define MSG_HOME_OFFSETS_APPLIED            "Offsets applied"
 #define MSG_SET_ORIGIN                      "Запомнить ноль"
-#define MSG_PREHEAT_PLA                     "Преднагрев PLA"
-#define MSG_PREHEAT_PLA_N                   "Греть PLA Сопло "
-#define MSG_PREHEAT_PLA_ALL                 "Греть PLA Все"
-#define MSG_PREHEAT_PLA_BEDONLY             "Греть PLA Стол"
-#define MSG_PREHEAT_PLA_SETTINGS            "Настройки PLA"
-#define MSG_PREHEAT_ABS                     "Преднагрев ABS"
-#define MSG_PREHEAT_ABS_N                   "Греть ABS Сопло "
-#define MSG_PREHEAT_ABS_ALL                 "Греть ABS Все"
-#define MSG_PREHEAT_ABS_BEDONLY             "Греть ABS Стол"
-#define MSG_PREHEAT_ABS_SETTINGS            "Настройки ABS"
+#define MSG_PREHEAT_1                       "Преднагрев PLA"
+#define MSG_PREHEAT_1_N                     "Греть PLA Сопло "
+#define MSG_PREHEAT_1_ALL                   "Греть PLA Все"
+#define MSG_PREHEAT_1_BEDONLY               "Греть PLA Стол"
+#define MSG_PREHEAT_1_SETTINGS              "Настройки PLA"
+#define MSG_PREHEAT_2                       "Преднагрев ABS"
+#define MSG_PREHEAT_2_N                     "Греть ABS Сопло "
+#define MSG_PREHEAT_2_ALL                   "Греть ABS Все"
+#define MSG_PREHEAT_2_BEDONLY               "Греть ABS Стол"
+#define MSG_PREHEAT_2_SETTINGS              "Настройки ABS"
 #define MSG_COOLDOWN                        "Охлаждение"
 #define MSG_SWITCH_PS_ON                    "Включить Питание"
 #define MSG_SWITCH_PS_OFF                   "Отключить Питание"

Marlin/language_test.h

@@ -141,8 +141,8 @@
   #define MSG_DISABLE_STEPPERS                STRG_C2_8
   #define MSG_AUTO_HOME                       STRG_C2_9
   #define MSG_SET_HOME_OFFSETS                STRG_C2_a
-  #define MSG_PREHEAT_PLA                     STRG_C2_b
-  #define MSG_PREHEAT_ABS                     STRG_C3_8
+  #define MSG_PREHEAT_1                       STRG_C2_b
+  #define MSG_PREHEAT_2                       STRG_C3_8
   #define MSG_COOLDOWN                        STRG_C3_9
   #define MSG_SWITCH_PS_OFF                   STRG_C3_a
   #define MSG_MOVE_AXIS                       STRG_C3_b
@@ -176,8 +176,8 @@
   #define MSG_DISABLE_STEPPERS                STRG_D0_8
   #define MSG_AUTO_HOME                       STRG_D0_9
   #define MSG_SET_HOME_OFFSETS                STRG_D0_a
-  #define MSG_PREHEAT_PLA                     STRG_D0_b
-  #define MSG_PREHEAT_ABS                     STRG_D1_8
+  #define MSG_PREHEAT_1                       STRG_D0_b
+  #define MSG_PREHEAT_2                       STRG_D1_8
   #define MSG_COOLDOWN                        STRG_D1_9
   #define MSG_SWITCH_PS_OFF                   STRG_D1_a
   #define MSG_MOVE_AXIS                       STRG_D1_b
@@ -211,8 +211,8 @@
   #define MSG_DISABLE_STEPPERS                STRG_E382_8
   #define MSG_AUTO_HOME                       STRG_E382_9
   #define MSG_SET_HOME_OFFSETS                STRG_E382_a
-  #define MSG_PREHEAT_PLA                     STRG_E382_b
-  #define MSG_PREHEAT_ABS                     STRG_E383_8
+  #define MSG_PREHEAT_1                       STRG_E382_b
+  #define MSG_PREHEAT_2                       STRG_E383_8
   #define MSG_COOLDOWN                        STRG_E383_9
   #define MSG_SWITCH_PS_OFF                   STRG_E383_a
   #define MSG_MOVE_AXIS                       STRG_E383_b

Marlin/ultralcd.cpp

@@ -33,13 +33,8 @@
   #include "printcounter.h"
 #endif
 
-int plaPreheatHotendTemp;
-int plaPreheatHPBTemp;
-int plaPreheatFanSpeed;
-
-int absPreheatHotendTemp;
-int absPreheatHPBTemp;
-int absPreheatFanSpeed;
+int preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1,
+    preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2;
 
 #if ENABLED(FILAMENT_LCD_DISPLAY)
   millis_t previous_lcd_status_ms = 0;
@@ -849,29 +844,29 @@ static void lcd_status_screen() {
   }
 
   #if TEMP_SENSOR_0 != 0
-    void lcd_preheat_pla0() { _lcd_preheat(0, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
-    void lcd_preheat_abs0() { _lcd_preheat(0, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
+    void lcd_preheat_pla0() { _lcd_preheat(0, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
+    void lcd_preheat_abs0() { _lcd_preheat(0, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
   #endif
 
   #if HOTENDS > 1
-    void lcd_preheat_pla1() { _lcd_preheat(1, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
-    void lcd_preheat_abs1() { _lcd_preheat(1, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
+    void lcd_preheat_pla1() { _lcd_preheat(1, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
+    void lcd_preheat_abs1() { _lcd_preheat(1, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
     #if HOTENDS > 2
-      void lcd_preheat_pla2() { _lcd_preheat(2, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
-      void lcd_preheat_abs2() { _lcd_preheat(2, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
+      void lcd_preheat_pla2() { _lcd_preheat(2, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
+      void lcd_preheat_abs2() { _lcd_preheat(2, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
       #if HOTENDS > 3
-        void lcd_preheat_pla3() { _lcd_preheat(3, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
-        void lcd_preheat_abs3() { _lcd_preheat(3, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
+        void lcd_preheat_pla3() { _lcd_preheat(3, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
+        void lcd_preheat_abs3() { _lcd_preheat(3, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
       #endif
     #endif
 
     void lcd_preheat_pla0123() {
       #if HOTENDS > 1
-        thermalManager.setTargetHotend(plaPreheatHotendTemp, 1);
+        thermalManager.setTargetHotend(preheatHotendTemp1, 1);
         #if HOTENDS > 2
-          thermalManager.setTargetHotend(plaPreheatHotendTemp, 2);
+          thermalManager.setTargetHotend(preheatHotendTemp1, 2);
           #if HOTENDS > 3
-            thermalManager.setTargetHotend(plaPreheatHotendTemp, 3);
+            thermalManager.setTargetHotend(preheatHotendTemp1, 3);
           #endif
         #endif
       #endif
@@ -879,11 +874,11 @@ static void lcd_status_screen() {
     }
     void lcd_preheat_abs0123() {
       #if HOTENDS > 1
-        thermalManager.setTargetHotend(absPreheatHotendTemp, 1);
+        thermalManager.setTargetHotend(preheatHotendTemp2, 1);
         #if HOTENDS > 2
-          thermalManager.setTargetHotend(absPreheatHotendTemp, 2);
+          thermalManager.setTargetHotend(preheatHotendTemp2, 2);
           #if HOTENDS > 3
-            thermalManager.setTargetHotend(absPreheatHotendTemp, 3);
+            thermalManager.setTargetHotend(preheatHotendTemp2, 3);
           #endif
         #endif
       #endif
@@ -893,8 +888,8 @@ static void lcd_status_screen() {
   #endif // HOTENDS > 1
 
   #if TEMP_SENSOR_BED != 0
-    void lcd_preheat_pla_bedonly() { _lcd_preheat(0, 0, plaPreheatHPBTemp, plaPreheatFanSpeed); }
-    void lcd_preheat_abs_bedonly() { _lcd_preheat(0, 0, absPreheatHPBTemp, absPreheatFanSpeed); }
+    void lcd_preheat_pla_bedonly() { _lcd_preheat(0, 0, preheatBedTemp1, preheatFanSpeed1); }
+    void lcd_preheat_abs_bedonly() { _lcd_preheat(0, 0, preheatBedTemp2, preheatFanSpeed2); }
   #endif
 
   #if TEMP_SENSOR_0 != 0 && (TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_BED != 0)
@@ -903,20 +898,20 @@ static void lcd_status_screen() {
       START_MENU();
       MENU_ITEM(back, MSG_PREPARE);
       #if HOTENDS == 1
-        MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla0);
+        MENU_ITEM(function, MSG_PREHEAT_1, lcd_preheat_pla0);
       #else
-        MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H1, lcd_preheat_pla0);
-        MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H2, lcd_preheat_pla1);
+        MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H1, lcd_preheat_pla0);
+        MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H2, lcd_preheat_pla1);
         #if HOTENDS > 2
-          MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H3, lcd_preheat_pla2);
+          MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H3, lcd_preheat_pla2);
           #if HOTENDS > 3
-            MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H4, lcd_preheat_pla3);
+            MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H4, lcd_preheat_pla3);
           #endif
         #endif
-        MENU_ITEM(function, MSG_PREHEAT_PLA_ALL, lcd_preheat_pla0123);
+        MENU_ITEM(function, MSG_PREHEAT_1_ALL, lcd_preheat_pla0123);
       #endif
       #if TEMP_SENSOR_BED != 0
-        MENU_ITEM(function, MSG_PREHEAT_PLA_BEDONLY, lcd_preheat_pla_bedonly);
+        MENU_ITEM(function, MSG_PREHEAT_1_BEDONLY, lcd_preheat_pla_bedonly);
       #endif
       END_MENU();
     }
@@ -925,20 +920,20 @@ static void lcd_status_screen() {
       START_MENU();
       MENU_ITEM(back, MSG_PREPARE);
       #if HOTENDS == 1
-        MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0);
+        MENU_ITEM(function, MSG_PREHEAT_2, lcd_preheat_abs0);
       #else
-        MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H1, lcd_preheat_abs0);
-        MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H2, lcd_preheat_abs1);
+        MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H1, lcd_preheat_abs0);
+        MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H2, lcd_preheat_abs1);
         #if HOTENDS > 2
-          MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H3, lcd_preheat_abs2);
+          MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H3, lcd_preheat_abs2);
           #if HOTENDS > 3
-            MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H4, lcd_preheat_abs3);
+            MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H4, lcd_preheat_abs3);
           #endif
         #endif
-        MENU_ITEM(function, MSG_PREHEAT_ABS_ALL, lcd_preheat_abs0123);
+        MENU_ITEM(function, MSG_PREHEAT_2_ALL, lcd_preheat_abs0123);
       #endif
       #if TEMP_SENSOR_BED != 0
-        MENU_ITEM(function, MSG_PREHEAT_ABS_BEDONLY, lcd_preheat_abs_bedonly);
+        MENU_ITEM(function, MSG_PREHEAT_2_BEDONLY, lcd_preheat_abs_bedonly);
       #endif
       END_MENU();
     }
@@ -1222,11 +1217,11 @@ static void lcd_status_screen() {
     //
     #if TEMP_SENSOR_0 != 0
       #if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_BED != 0
-        MENU_ITEM(submenu, MSG_PREHEAT_PLA, lcd_preheat_pla_menu);
-        MENU_ITEM(submenu, MSG_PREHEAT_ABS, lcd_preheat_abs_menu);
+        MENU_ITEM(submenu, MSG_PREHEAT_1, lcd_preheat_pla_menu);
+        MENU_ITEM(submenu, MSG_PREHEAT_2, lcd_preheat_abs_menu);
       #else
-        MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla0);
-        MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0);
+        MENU_ITEM(function, MSG_PREHEAT_1, lcd_preheat_pla0);
+        MENU_ITEM(function, MSG_PREHEAT_2, lcd_preheat_abs0);
       #endif
     #endif
 
@@ -1685,12 +1680,12 @@ static void lcd_status_screen() {
     //
     // Preheat PLA conf
     //
-    MENU_ITEM(submenu, MSG_PREHEAT_PLA_SETTINGS, lcd_control_temperature_preheat_pla_settings_menu);
+    MENU_ITEM(submenu, MSG_PREHEAT_1_SETTINGS, lcd_control_temperature_preheat_pla_settings_menu);
 
     //
     // Preheat ABS conf
     //
-    MENU_ITEM(submenu, MSG_PREHEAT_ABS_SETTINGS, lcd_control_temperature_preheat_abs_settings_menu);
+    MENU_ITEM(submenu, MSG_PREHEAT_2_SETTINGS, lcd_control_temperature_preheat_abs_settings_menu);
     END_MENU();
   }
 
@@ -1702,12 +1697,12 @@ static void lcd_status_screen() {
   static void lcd_control_temperature_preheat_pla_settings_menu() {
     START_MENU();
     MENU_ITEM(back, MSG_TEMPERATURE);
-    MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &plaPreheatFanSpeed, 0, 255);
+    MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &preheatFanSpeed1, 0, 255);
     #if TEMP_SENSOR_0 != 0
-      MENU_ITEM_EDIT(int3, MSG_NOZZLE, &plaPreheatHotendTemp, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
+      MENU_ITEM_EDIT(int3, MSG_NOZZLE, &preheatHotendTemp1, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
     #endif
     #if TEMP_SENSOR_BED != 0
-      MENU_ITEM_EDIT(int3, MSG_BED, &plaPreheatHPBTemp, BED_MINTEMP, BED_MAXTEMP - 15);
+      MENU_ITEM_EDIT(int3, MSG_BED, &preheatBedTemp1, BED_MINTEMP, BED_MAXTEMP - 15);
     #endif
     #if ENABLED(EEPROM_SETTINGS)
       MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings);
@@ -1723,12 +1718,12 @@ static void lcd_status_screen() {
   static void lcd_control_temperature_preheat_abs_settings_menu() {
     START_MENU();
     MENU_ITEM(back, MSG_TEMPERATURE);
-    MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &absPreheatFanSpeed, 0, 255);
+    MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &preheatFanSpeed2, 0, 255);
     #if TEMP_SENSOR_0 != 0
-      MENU_ITEM_EDIT(int3, MSG_NOZZLE, &absPreheatHotendTemp, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
+      MENU_ITEM_EDIT(int3, MSG_NOZZLE, &preheatHotendTemp2, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
     #endif
     #if TEMP_SENSOR_BED != 0
-      MENU_ITEM_EDIT(int3, MSG_BED, &absPreheatHPBTemp, BED_MINTEMP, BED_MAXTEMP - 15);
+      MENU_ITEM_EDIT(int3, MSG_BED, &preheatBedTemp2, BED_MINTEMP, BED_MAXTEMP - 15);
     #endif
     #if ENABLED(EEPROM_SETTINGS)
       MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings);

Marlin/ultralcd.h

@@ -88,12 +88,12 @@
     FORCE_INLINE void lcd_buttons_update() {}
   #endif
 
-  extern int plaPreheatHotendTemp;
-  extern int plaPreheatHPBTemp;
-  extern int plaPreheatFanSpeed;
-  extern int absPreheatHotendTemp;
-  extern int absPreheatHPBTemp;
-  extern int absPreheatFanSpeed;
+  extern int preheatHotendTemp1;
+  extern int preheatBedTemp1;
+  extern int preheatFanSpeed1;
+  extern int preheatHotendTemp2;
+  extern int preheatBedTemp2;
+  extern int preheatFanSpeed2;
 
   #if ENABLED(FILAMENT_LCD_DISPLAY)
     extern millis_t previous_lcd_status_ms;