Merge pull request #547 from wolfmanjm/delta-configuration

Setup Default configuration for Deltas if DELTA is defined

Marlin/Marlin_main.cpp

@@ -759,7 +759,11 @@ static void homeaxis(int axis) {
     st_synchronize();
 
     destination[axis] = 2*home_retract_mm(axis) * axis_home_dir;
+#ifdef DELTA
+    feedrate = homing_feedrate[axis]/10;
+#else
     feedrate = homing_feedrate[axis]/2 ;
+#endif
     plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder);
     st_synchronize();
 

Marlin/example_configurations/delta/Configuration.h

@@ -0,0 +1,585 @@
+#ifndef CONFIGURATION_H
+#define CONFIGURATION_H
+
+// This configuration file contains the basic settings.
+// Advanced settings can be found in Configuration_adv.h
+// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
+
+// User-specified version info of this build to display in [Pronterface, etc] terminal window during
+// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
+// build by the user have been successfully uploaded into firmware.
+#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time
+#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+
+// SERIAL_PORT selects which serial port should be used for communication with the host.
+// This allows the connection of wireless adapters (for instance) to non-default port pins.
+// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
+#define SERIAL_PORT 0
+
+// This determines the communication speed of the printer
+#define BAUDRATE 250000
+//#define BAUDRATE 115200
+
+//// The following define selects which electronics board you have. Please choose the one that matches your setup
+// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
+// 11 = Gen7 v1.1, v1.2 = 11
+// 12 = Gen7 v1.3
+// 13 = Gen7 v1.4
+// 3  = MEGA/RAMPS up to 1.2 = 3
+// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
+// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
+// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
+// 4  = Duemilanove w/ ATMega328P pin assignment
+// 5  = Gen6
+// 51 = Gen6 deluxe
+// 6  = Sanguinololu < 1.2
+// 62 = Sanguinololu 1.2 and above
+// 63 = Melzi
+// 64 = STB V1.1
+// 65 = Azteeg X1
+// 66 = Melzi with ATmega1284 (MaKr3d version)
+// 7  = Ultimaker
+// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
+// 77 = 3Drag Controller
+// 8  = Teensylu
+// 80 = Rumba
+// 81 = Printrboard (AT90USB1286)
+// 82 = Brainwave (AT90USB646)
+// 9  = Gen3+
+// 70 = Megatronics
+// 701= Megatronics v2.0
+// 702= Minitronics v1.0
+// 90 = Alpha OMCA board
+// 91 = Final OMCA board
+// 301 = Rambo
+// 21 = Elefu Ra Board (v3)
+
+#ifndef MOTHERBOARD
+#define MOTHERBOARD 33
+#endif
+
+// Define this to set a custom name for your generic Mendel,
+// #define CUSTOM_MENDEL_NAME "This Mendel"
+
+// This defines the number of extruders
+#define EXTRUDERS 1
+
+//// The following define selects which power supply you have. Please choose the one that matches your setup
+// 1 = ATX
+// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
+
+#define POWER_SUPPLY 1
+
+
+//===========================================================================
+//============================== Delta Settings =============================
+//===========================================================================
+// Enable DELTA kinematics and most of the default configuration for Deltas
+#define DELTA
+
+// Make delta curves from many straight lines (linear interpolation).
+// This is a trade-off between visible corners (not enough segments)
+// and processor overload (too many expensive sqrt calls).
+#define DELTA_SEGMENTS_PER_SECOND 200
+
+// Center-to-center distance of the holes in the diagonal push rods.
+#define DELTA_DIAGONAL_ROD 250.0 // mm
+
+// Horizontal offset from middle of printer to smooth rod center.
+#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm
+
+// Horizontal offset of the universal joints on the end effector.
+#define DELTA_EFFECTOR_OFFSET 33.0 // mm
+
+// Horizontal offset of the universal joints on the carriages.
+#define DELTA_CARRIAGE_OFFSET 18.0 // mm
+
+// Effective horizontal distance bridged by diagonal push rods.
+#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
+
+// Effective X/Y positions of the three vertical towers.
+#define SIN_60 0.8660254037844386
+#define COS_60 0.5
+#define DELTA_TOWER1_X -SIN_60*DELTA_RADIUS // front left tower
+#define DELTA_TOWER1_Y -COS_60*DELTA_RADIUS
+#define DELTA_TOWER2_X SIN_60*DELTA_RADIUS // front right tower
+#define DELTA_TOWER2_Y -COS_60*DELTA_RADIUS
+#define DELTA_TOWER3_X 0.0 // back middle tower
+#define DELTA_TOWER3_Y DELTA_RADIUS
+
+//===========================================================================
+//=============================Thermal Settings  ============================
+//===========================================================================
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 60 is 100k Maker's Tool Works Kapton Bed Thermister
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan) (1k pullup)
+
+#define TEMP_SENSOR_0 -1
+#define TEMP_SENSOR_1 -1
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_BED 0
+
+// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
+//#define TEMP_SENSOR_1_AS_REDUNDANT 
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
+
+// Actual temperature must be close to target for this long before M109 returns success
+#define TEMP_RESIDENCY_TIME 10  // (seconds)
+#define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// The minimal temperature defines the temperature below which the heater will not be enabled It is used
+// to check that the wiring to the thermistor is not broken.
+// Otherwise this would lead to the heater being powered on all the time.
+#define HEATER_0_MINTEMP 5
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define BED_MINTEMP 5
+
+// When temperature exceeds max temp, your heater will be switched off.
+// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
+// You should use MINTEMP for thermistor short/failure protection.
+#define HEATER_0_MAXTEMP 275
+#define HEATER_1_MAXTEMP 275
+#define HEATER_2_MAXTEMP 275
+#define BED_MAXTEMP 150
+
+// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
+// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
+// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
+//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
+
+// PID settings:
+// Comment the following line to disable PID and enable bang-bang.
+#define PIDTEMP
+#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define PID_MAX 255 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#ifdef PIDTEMP
+  //#define PID_DEBUG // Sends debug data to the serial port.
+  //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
+  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+                                  // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+  #define PID_INTEGRAL_DRIVE_MAX 255  //limit for the integral term
+  #define K1 0.95 //smoothing factor within the PID
+  #define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
+
+// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it
+// Ultimaker
+    #define  DEFAULT_Kp 22.2
+    #define  DEFAULT_Ki 1.08
+    #define  DEFAULT_Kd 114
+
+// Makergear
+//    #define  DEFAULT_Kp 7.0
+//    #define  DEFAULT_Ki 0.1
+//    #define  DEFAULT_Kd 12
+
+// Mendel Parts V9 on 12V
+//    #define  DEFAULT_Kp 63.0
+//    #define  DEFAULT_Ki 2.25
+//    #define  DEFAULT_Kd 440
+#endif // PIDTEMP
+
+// Bed Temperature Control
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+//#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+    #define  DEFAULT_bedKp 10.00
+    #define  DEFAULT_bedKi .023
+    #define  DEFAULT_bedKd 305.4
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+//    #define  DEFAULT_bedKp 97.1
+//    #define  DEFAULT_bedKi 1.41
+//    #define  DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+
+//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
+//can be software-disabled for whatever purposes by
+#define PREVENT_DANGEROUS_EXTRUDE
+//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
+#define PREVENT_LENGTHY_EXTRUDE
+
+#define EXTRUDE_MINTEMP 170
+#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
+
+//===========================================================================
+//=============================Mechanical Settings===========================
+//===========================================================================
+
+// Uncomment the following line to enable CoreXY kinematics
+// #define COREXY
+
+// coarse Endstop Settings
+#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
+
+#ifndef ENDSTOPPULLUPS
+  // fine Enstop settings: Individual Pullups. will be ignored if ENDSTOPPULLUPS is defined
+  // #define ENDSTOPPULLUP_XMAX
+  // #define ENDSTOPPULLUP_YMAX
+  // #define ENDSTOPPULLUP_ZMAX
+  // #define ENDSTOPPULLUP_XMIN
+  // #define ENDSTOPPULLUP_YMIN
+  // #define ENDSTOPPULLUP_ZMIN
+#endif
+
+#ifdef ENDSTOPPULLUPS
+  #define ENDSTOPPULLUP_XMAX
+  #define ENDSTOPPULLUP_YMAX
+  #define ENDSTOPPULLUP_ZMAX
+  #define ENDSTOPPULLUP_XMIN
+  #define ENDSTOPPULLUP_YMIN
+  #define ENDSTOPPULLUP_ZMIN
+#endif
+
+// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+const bool X_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
+const bool Y_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
+const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
+
+// deltas never have min endstops
+#define DISABLE_MIN_ENDSTOPS
+
+// Disable max endstops for compatibility with endstop checking routine
+#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
+  #define DISABLE_MAX_ENDSTOPS
+#endif
+
+// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+#define X_ENABLE_ON 0
+#define Y_ENABLE_ON 0
+#define Z_ENABLE_ON 0
+#define E_ENABLE_ON 0 // For all extruders
+
+// Disables axis when it's not being used.
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+#define DISABLE_E false // For all extruders
+
+#define INVERT_X_DIR false // DELTA does not invert
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR false
+
+#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+
+// ENDSTOP SETTINGS:
+// Sets direction of endstops when homing; 1=MAX, -1=MIN
+// deltas always home to max
+#define X_HOME_DIR 1
+#define Y_HOME_DIR 1
+#define Z_HOME_DIR 1
+
+#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
+#define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
+
+// Travel limits after homing
+#define X_MAX_POS 90
+#define X_MIN_POS -90
+#define Y_MAX_POS 90
+#define Y_MIN_POS -90
+#define Z_MAX_POS MANUAL_Z_HOME_POS
+#define Z_MIN_POS 0
+
+#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
+#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
+#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+// The position of the homing switches
+//#define MANUAL_HOME_POSITIONS  // If defined, MANUAL_*_HOME_POS below will be used
+//#define BED_CENTER_AT_0_0  // If defined, the center of the bed is at (X=0, Y=0)
+
+//Manual homing switch locations:
+
+#define MANUAL_HOME_POSITIONS  // MANUAL_*_HOME_POS below will be used
+// For deltabots this means top and center of the cartesian print volume.
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS 0
+#define MANUAL_Z_HOME_POS 250 // For delta: Distance between nozzle and print surface after homing.
+
+//// MOVEMENT SETTINGS
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+
+// delta homing speeds must be the same on xyz
+#define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0}  // set the homing speeds (mm/min)
+
+// default settings
+// delta speeds must be the same on xyz
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {80, 80, 80, 760*1.1}  // default steps per unit for Kossel (GT2, 20 tooth)
+#define DEFAULT_MAX_FEEDRATE          {500, 500, 500, 25}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {9000,9000,9000,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  3000   // X, Y, Z and E max acceleration in mm/s^2 for retracts
+
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+// #define EXTRUDER_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
+
+// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
+#define DEFAULT_XYJERK                20.0    // (mm/sec)
+#define DEFAULT_ZJERK                 20.0    // (mm/sec) Must be same as XY for delta
+#define DEFAULT_EJERK                 5.0    // (mm/sec)
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+// EEPROM
+// the microcontroller can store settings in the EEPROM, e.g. max velocity...
+// M500 - stores paramters in EEPROM
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
+// M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
+//define this to enable eeprom support
+//#define EEPROM_SETTINGS
+//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
+// please keep turned on if you can.
+//#define EEPROM_CHITCHAT
+
+// Preheat Constants
+#define PLA_PREHEAT_HOTEND_TEMP 180 
+#define PLA_PREHEAT_HPB_TEMP 70
+#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+
+#define ABS_PREHEAT_HOTEND_TEMP 240
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+
+//LCD and SD support
+//#define ULTRA_LCD  //general lcd support, also 16x2
+//#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
+//#define SDSUPPORT // Enable SD Card Support in Hardware Console
+//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
+
+//#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
+//#define ULTIPANEL  //the ultipanel as on thingiverse
+
+// The MaKr3d Makr-Panel with graphic controller and SD support
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//#define MAKRPANEL
+
+// The RepRapDiscount Smart Controller (white PCB)
+// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
+//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+
+// The GADGETS3D G3D LCD/SD Controller (blue PCB)
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+//#define G3D_PANEL
+
+// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
+// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
+// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
+//#define REPRAPWORLD_KEYPAD
+//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
+
+// The Elefu RA Board Control Panel
+// http://www.elefu.com/index.php?route=product/product&product_id=53
+// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARUDINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
+//#define RA_CONTROL_PANEL
+
+//automatic expansion
+#if defined (MAKRPANEL)
+ #define DOGLCD
+ #define SDSUPPORT
+ #define ULTIPANEL
+ #define NEWPANEL
+ #define DEFAULT_LCD_CONTRAST 17
+#endif
+
+#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+ #define DOGLCD
+ #define U8GLIB_ST7920
+ #define REPRAP_DISCOUNT_SMART_CONTROLLER
+#endif
+
+#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
+ #define ULTIPANEL
+ #define NEWPANEL
+#endif
+
+#if defined(REPRAPWORLD_KEYPAD)
+  #define NEWPANEL
+  #define ULTIPANEL
+#endif
+#if defined(RA_CONTROL_PANEL)
+ #define ULTIPANEL
+ #define NEWPANEL
+ #define LCD_I2C_TYPE_PCA8574
+ #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
+#endif
+
+//I2C PANELS
+
+//#define LCD_I2C_SAINSMART_YWROBOT
+#ifdef LCD_I2C_SAINSMART_YWROBOT
+  // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
+  // Make sure it is placed in the Arduino libraries directory.
+  #define LCD_I2C_TYPE_PCF8575
+  #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
+  #define NEWPANEL
+  #define ULTIPANEL 
+#endif
+
+// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
+//#define LCD_I2C_PANELOLU2
+#ifdef LCD_I2C_PANELOLU2
+  // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+  // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+  // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
+  // Note: The PANELOLU2 encoder click input can either be directly connected to a pin 
+  //       (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). 
+  #define LCD_I2C_TYPE_MCP23017
+  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+  #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
+  #define NEWPANEL
+  #define ULTIPANEL 
+#endif
+
+// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
+//#define LCD_I2C_VIKI
+#ifdef LCD_I2C_VIKI
+  // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+  // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+  // Note: The pause/stop/resume LCD button pin should be connected to the Arduino
+  //       BTN_ENC pin (or set BTN_ENC to -1 if not used)
+  #define LCD_I2C_TYPE_MCP23017 
+  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+  #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
+  #define NEWPANEL
+  #define ULTIPANEL 
+#endif
+
+#ifdef ULTIPANEL
+//  #define NEWPANEL  //enable this if you have a click-encoder panel
+  #define SDSUPPORT
+  #define ULTRA_LCD
+  #ifdef DOGLCD // Change number of lines to match the DOG graphic display
+    #define LCD_WIDTH 20
+    #define LCD_HEIGHT 5
+  #else
+    #define LCD_WIDTH 20
+    #define LCD_HEIGHT 4
+  #endif
+#else //no panel but just lcd
+  #ifdef ULTRA_LCD
+  #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
+    #define LCD_WIDTH 20
+    #define LCD_HEIGHT 5
+  #else
+    #define LCD_WIDTH 16
+    #define LCD_HEIGHT 2
+  #endif
+  #endif
+#endif
+
+// default LCD contrast for dogm-like LCD displays
+#ifdef DOGLCD
+# ifndef DEFAULT_LCD_CONTRAST
+#  define DEFAULT_LCD_CONTRAST 32
+# endif
+#endif
+
+// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
+//#define FAST_PWM_FAN
+
+// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
+// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// is too low, you should also increment SOFT_PWM_SCALE.
+//#define FAN_SOFT_PWM
+
+// Incrementing this by 1 will double the software PWM frequency,
+// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
+// However, control resolution will be halved for each increment;
+// at zero value, there are 128 effective control positions.
+#define SOFT_PWM_SCALE 0
+
+// M240  Triggers a camera by emulating a Canon RC-1 Remote
+// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
+// #define PHOTOGRAPH_PIN     23
+
+// SF send wrong arc g-codes when using Arc Point as fillet procedure
+//#define SF_ARC_FIX
+
+// Support for the BariCUDA Paste Extruder.
+//#define BARICUDA
+
+/*********************************************************************\
+* R/C SERVO support
+* Sponsored by TrinityLabs, Reworked by codexmas
+**********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it undefined or defining as 0 will disable the servo subsystem
+// If unsure, leave commented / disabled
+//
+//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+
+// Servo Endstops
+// 
+// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
+// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
+// 
+//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
+//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
+
+#include "Configuration_adv.h"
+#include "thermistortables.h"
+
+#endif //__CONFIGURATION_H

Marlin/example_configurations/delta/Configuration_adv.h

@@ -0,0 +1,396 @@
+#ifndef CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H
+
+//===========================================================================
+//=============================Thermal Settings  ============================
+//===========================================================================
+
+#ifdef BED_LIMIT_SWITCHING
+  #define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
+#endif
+#define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control
+
+//// Heating sanity check:
+// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
+// If the temperature has not increased at the end of that period, the target temperature is set to zero. 
+// It can be reset with another M104/M109. This check is also only triggered if the target temperature and the current temperature
+//  differ by at least 2x WATCH_TEMP_INCREASE
+//#define WATCH_TEMP_PERIOD 40000 //40 seconds
+//#define WATCH_TEMP_INCREASE 10  //Heat up at least 10 degree in 20 seconds
+
+#ifdef PIDTEMP
+  // this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
+  // if Kc is choosen well, the additional required power due to increased melting should be compensated.
+  #define PID_ADD_EXTRUSION_RATE  
+  #ifdef PID_ADD_EXTRUSION_RATE
+    #define  DEFAULT_Kc (1) //heatingpower=Kc*(e_speed)
+  #endif
+#endif
+
+
+//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
+//The maximum buffered steps/sec of the extruder motor are called "se".
+//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
+// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
+// you exit the value by any M109 without F*
+// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
+// on an ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+#define AUTOTEMP
+#ifdef AUTOTEMP
+  #define AUTOTEMP_OLDWEIGHT 0.98
+#endif
+
+//  extruder run-out prevention. 
+//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
+//#define EXTRUDER_RUNOUT_PREVENT  
+#define EXTRUDER_RUNOUT_MINTEMP 190  
+#define EXTRUDER_RUNOUT_SECONDS 30.
+#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
+#define EXTRUDER_RUNOUT_SPEED 1500.  //extrusion speed
+#define EXTRUDER_RUNOUT_EXTRUDE 100
+
+//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
+//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
+#define TEMP_SENSOR_AD595_OFFSET 0.0
+#define TEMP_SENSOR_AD595_GAIN   1.0
+
+//This is for controlling a fan to cool down the stepper drivers
+//it will turn on when any driver is enabled
+//and turn off after the set amount of seconds from last driver being disabled again
+#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable)
+#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
+#define CONTROLLERFAN_SPEED 255  // == full speed
+
+// When first starting the main fan, run it at full speed for the
+// given number of milliseconds.  This gets the fan spinning reliably
+// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
+//#define FAN_KICKSTART_TIME 100
+
+// Extruder cooling fans
+// Configure fan pin outputs to automatically turn on/off when the associated
+// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
+// Multiple extruders can be assigned to the same pin in which case 
+// the fan will turn on when any selected extruder is above the threshold.
+#define EXTRUDER_0_AUTO_FAN_PIN   -1
+#define EXTRUDER_1_AUTO_FAN_PIN   -1
+#define EXTRUDER_2_AUTO_FAN_PIN   -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
+
+
+//===========================================================================
+//=============================Mechanical Settings===========================
+//===========================================================================
+
+#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
+
+
+//// AUTOSET LOCATIONS OF LIMIT SWITCHES
+//// Added by ZetaPhoenix 09-15-2012
+#ifdef MANUAL_HOME_POSITIONS  // Use manual limit switch locations
+  #define X_HOME_POS MANUAL_X_HOME_POS
+  #define Y_HOME_POS MANUAL_Y_HOME_POS
+  #define Z_HOME_POS MANUAL_Z_HOME_POS
+#else //Set min/max homing switch positions based upon homing direction and min/max travel limits
+  //X axis
+  #if X_HOME_DIR == -1
+    #ifdef BED_CENTER_AT_0_0
+      #define X_HOME_POS X_MAX_LENGTH * -0.5
+    #else
+      #define X_HOME_POS X_MIN_POS
+    #endif //BED_CENTER_AT_0_0
+  #else    
+    #ifdef BED_CENTER_AT_0_0
+      #define X_HOME_POS X_MAX_LENGTH * 0.5
+    #else
+      #define X_HOME_POS X_MAX_POS
+    #endif //BED_CENTER_AT_0_0
+  #endif //X_HOME_DIR == -1
+  
+  //Y axis
+  #if Y_HOME_DIR == -1
+    #ifdef BED_CENTER_AT_0_0
+      #define Y_HOME_POS Y_MAX_LENGTH * -0.5
+    #else
+      #define Y_HOME_POS Y_MIN_POS
+    #endif //BED_CENTER_AT_0_0
+  #else    
+    #ifdef BED_CENTER_AT_0_0
+      #define Y_HOME_POS Y_MAX_LENGTH * 0.5
+    #else
+      #define Y_HOME_POS Y_MAX_POS
+    #endif //BED_CENTER_AT_0_0
+  #endif //Y_HOME_DIR == -1
+  
+  // Z axis
+  #if Z_HOME_DIR == -1 //BED_CENTER_AT_0_0 not used
+    #define Z_HOME_POS Z_MIN_POS
+  #else    
+    #define Z_HOME_POS Z_MAX_POS
+  #endif //Z_HOME_DIR == -1
+#endif //End auto min/max positions
+//END AUTOSET LOCATIONS OF LIMIT SWITCHES -ZP
+
+
+//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
+
+// A single Z stepper driver is usually used to drive 2 stepper motors.
+// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
+// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
+// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
+// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
+//#define Z_DUAL_STEPPER_DRIVERS
+
+#ifdef Z_DUAL_STEPPER_DRIVERS
+  #undef EXTRUDERS
+  #define EXTRUDERS 1
+#endif
+
+// Enable this for dual x-carriage printers. 
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds.
+//#define DUAL_X_CARRIAGE
+#ifdef DUAL_X_CARRIAGE
+// Configuration for second X-carriage
+// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+// the second x-carriage always homes to the maximum endstop.
+#define X2_MIN_POS 88     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+#define X2_MAX_POS 350.45 // set maximum to the distance between toolheads when both heads are homed 
+#define X2_HOME_DIR 1     // the second X-carriage always homes to the maximum endstop position
+#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position 
+    // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software 
+    // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
+    // without modifying the firmware (through the "M218 T1 X???" command).
+    // Remember: you should set the second extruder x-offset to 0 in your slicer.
+
+// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
+#define X2_ENABLE_PIN 29
+#define X2_STEP_PIN 25
+#define X2_DIR_PIN 23
+
+#endif // DUAL_X_CARRIAGE
+    
+//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+#define X_HOME_RETRACT_MM 5 
+#define Y_HOME_RETRACT_MM 5
+#define Z_HOME_RETRACT_MM 5 // deltas need the same for all three axis
+
+
+//#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
+
+#define AXIS_RELATIVE_MODES {false, false, false, false}
+
+#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
+
+//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
+#define INVERT_X_STEP_PIN false
+#define INVERT_Y_STEP_PIN false
+#define INVERT_Z_STEP_PIN false
+#define INVERT_E_STEP_PIN false
+
+//default stepper release if idle
+#define DEFAULT_STEPPER_DEACTIVE_TIME 60
+
+#define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
+#define DEFAULT_MINTRAVELFEEDRATE     0.0
+
+// minimum time in microseconds that a movement needs to take if the buffer is emptied.
+#define DEFAULT_MINSEGMENTTIME        20000
+
+// If defined the movements slow down when the look ahead buffer is only half full
+// (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second)
+//#define SLOWDOWN
+
+// Frequency limit
+// See nophead's blog for more info
+// Not working O
+//#define XY_FREQUENCY_LIMIT  15
+
+// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
+// of the buffer and all stops. This should not be much greater than zero and should only be changed
+// if unwanted behavior is observed on a user's machine when running at very slow speeds.
+#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
+
+// MS1 MS2 Stepper Driver Microstepping mode table
+#define MICROSTEP1 LOW,LOW
+#define MICROSTEP2 HIGH,LOW
+#define MICROSTEP4 LOW,HIGH
+#define MICROSTEP8 HIGH,HIGH
+#define MICROSTEP16 HIGH,HIGH
+
+// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
+#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
+
+// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+#define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
+#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+
+// The hardware watchdog should reset the Microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
+//#define USE_WATCHDOG
+
+#ifdef USE_WATCHDOG
+// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
+// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
+//  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
+//#define WATCHDOG_RESET_MANUAL
+#endif
+
+// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled.
+//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+
+// extruder advance constant (s2/mm3)
+//
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
+//
+// hooke's law says:		force = k * distance
+// bernoulli's priniciple says:	v ^ 2 / 2 + g . h + pressure / density = constant
+// so: v ^ 2 is proportional to number of steps we advance the extruder
+//#define ADVANCE
+
+#ifdef ADVANCE
+  #define EXTRUDER_ADVANCE_K .0
+
+  #define D_FILAMENT 2.85
+  #define STEPS_MM_E 836
+  #define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
+  #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
+
+#endif // ADVANCE
+
+// Arc interpretation settings:
+#define MM_PER_ARC_SEGMENT 1
+#define N_ARC_CORRECTION 25
+
+const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
+
+// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT 
+// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+// be commented out otherwise
+#define SDCARDDETECTINVERTED 
+
+#ifdef ULTIPANEL
+ #undef SDCARDDETECTINVERTED
+#endif
+
+// Power Signal Control Definitions
+// By default use ATX definition
+#ifndef POWER_SUPPLY
+  #define POWER_SUPPLY 1
+#endif
+// 1 = ATX
+#if (POWER_SUPPLY == 1) 
+  #define PS_ON_AWAKE  LOW
+  #define PS_ON_ASLEEP HIGH
+#endif
+// 2 = X-Box 360 203W
+#if (POWER_SUPPLY == 2) 
+  #define PS_ON_AWAKE  HIGH
+  #define PS_ON_ASLEEP LOW
+#endif
+
+//===========================================================================
+//=============================Buffers           ============================
+//===========================================================================
+
+// The number of linear motions that can be in the plan at any give time.  
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
+#if defined SDSUPPORT
+  #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+#else
+  #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+#endif
+
+
+//The ASCII buffer for recieving from the serial:
+#define MAX_CMD_SIZE 96
+#define BUFSIZE 4
+
+
+// Firmware based and LCD controled retract
+// M207 and M208 can be used to define parameters for the retraction. 
+// The retraction can be called by the slicer using G10 and G11
+// until then, intended retractions can be detected by moves that only extrude and the direction. 
+// the moves are than replaced by the firmware controlled ones.
+
+// #define FWRETRACT  //ONLY PARTIALLY TESTED
+#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
+
+
+//adds support for experimental filament exchange support M600; requires display
+#ifdef ULTIPANEL
+  //#define FILAMENTCHANGEENABLE
+  #ifdef FILAMENTCHANGEENABLE
+    #define FILAMENTCHANGE_XPOS 3
+    #define FILAMENTCHANGE_YPOS 3
+    #define FILAMENTCHANGE_ZADD 10
+    #define FILAMENTCHANGE_FIRSTRETRACT -2
+    #define FILAMENTCHANGE_FINALRETRACT -100
+  #endif
+#endif
+ 
+//===========================================================================
+//=============================  Define Defines  ============================
+//===========================================================================
+#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
+  #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
+#endif
+
+#if TEMP_SENSOR_0 > 0
+  #define THERMISTORHEATER_0 TEMP_SENSOR_0
+  #define HEATER_0_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_1 > 0
+  #define THERMISTORHEATER_1 TEMP_SENSOR_1
+  #define HEATER_1_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_2 > 0
+  #define THERMISTORHEATER_2 TEMP_SENSOR_2
+  #define HEATER_2_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_BED > 0
+  #define THERMISTORBED TEMP_SENSOR_BED
+  #define BED_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_0 == -1
+  #define HEATER_0_USES_AD595
+#endif
+#if TEMP_SENSOR_1 == -1
+  #define HEATER_1_USES_AD595
+#endif
+#if TEMP_SENSOR_2 == -1
+  #define HEATER_2_USES_AD595
+#endif
+#if TEMP_SENSOR_BED == -1
+  #define BED_USES_AD595
+#endif
+#if TEMP_SENSOR_0 == -2
+  #define HEATER_0_USES_MAX6675
+#endif
+#if TEMP_SENSOR_0 == 0
+  #undef HEATER_0_MINTEMP
+  #undef HEATER_0_MAXTEMP
+#endif
+#if TEMP_SENSOR_1 == 0
+  #undef HEATER_1_MINTEMP
+  #undef HEATER_1_MAXTEMP
+#endif
+#if TEMP_SENSOR_2 == 0
+  #undef HEATER_2_MINTEMP
+  #undef HEATER_2_MAXTEMP
+#endif
+#if TEMP_SENSOR_BED == 0
+  #undef BED_MINTEMP
+  #undef BED_MAXTEMP
+#endif
+
+
+#endif //__CONFIGURATION_ADV_H