|
@@ -5,9 +5,35 @@
|
5
|
5
|
#include "pins_RAMPS_13.h"
|
6
|
6
|
|
7
|
7
|
#undef FAN_PIN
|
8
|
|
-#define FAN_PIN 9 // (Sprinter config)
|
9
|
|
-
|
|
8
|
+#define FAN_PIN 6 //Part Cooling System
|
10
|
9
|
#define BEEPER 33
|
|
10
|
+#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable)
|
|
11
|
+//Fans/Water Pump to cool the hotend cool side.
|
|
12
|
+#define EXTRUDER_0_AUTO_FAN_PIN 5
|
|
13
|
+#define EXTRUDER_1_AUTO_FAN_PIN 5
|
|
14
|
+#define EXTRUDER_2_AUTO_FAN_PIN 5
|
|
15
|
+#define EXTRUDER_3_AUTO_FAN_PIN 5
|
|
16
|
+//
|
|
17
|
+//This section is to swap the MIN and MAX pins because the X3 Pro comes with only
|
|
18
|
+//MIN endstops soldered onto the board. Delta code wants the homing endstops to be
|
|
19
|
+//the MAX so I swapped them here. Comment them out with // if you want them original.
|
|
20
|
+//Note: I had to solder on the additional MAX Endstop pins to attach a Z-Probe
|
|
21
|
+//endstop switch.
|
|
22
|
+//
|
|
23
|
+#undef X_MIN_PIN
|
|
24
|
+#undef X_MAX_PIN
|
|
25
|
+#undef Y_MIN_PIN
|
|
26
|
+#undef Y_MAX_PIN
|
|
27
|
+#undef Z_MIN_PIN
|
|
28
|
+#undef Z_MAX_PIN
|
|
29
|
+
|
|
30
|
+#define X_MIN_PIN 2
|
|
31
|
+#define X_MAX_PIN 3
|
|
32
|
+#define Y_MIN_PIN 15
|
|
33
|
+#define Y_MAX_PIN 14
|
|
34
|
+#define Z_MIN_PIN 19
|
|
35
|
+#define Z_MAX_PIN 18
|
|
36
|
+//
|
11
|
37
|
|
12
|
38
|
#define E2_STEP_PIN 23
|
13
|
39
|
#define E2_DIR_PIN 25
|
|
@@ -24,7 +50,7 @@
|
24
|
50
|
#undef HEATER_1_PIN
|
25
|
51
|
#undef HEATER_2_PIN
|
26
|
52
|
#undef HEATER_3_PIN
|
27
|
|
-#define HEATER_1_PIN -1
|
|
53
|
+#define HEATER_1_PIN 9
|
28
|
54
|
#define HEATER_2_PIN 16
|
29
|
55
|
#define HEATER_3_PIN 17
|
30
|
56
|
#define HEATER_4_PIN 4
|
|
@@ -39,3 +65,26 @@
|
39
|
65
|
#define TEMP_4_PIN 10 // ANALOG NUMBERING
|
40
|
66
|
#define TC1 4 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
|
41
|
67
|
#define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
|
|
68
|
+
|
|
69
|
+//
|
|
70
|
+//These Servo pins are for when they are defined. Tested for usage with bed leveling
|
|
71
|
+//on a Delta with 1 servo. Running through the Z servo endstop in code.
|
|
72
|
+//Physical wire attachment was done on EXT1 on the GND, 5V, and D47 pins.
|
|
73
|
+//
|
|
74
|
+#undef SERVO0_PIN
|
|
75
|
+#undef SERVO1_PIN
|
|
76
|
+#undef SERVO2_PIN
|
|
77
|
+#undef SERVO3_PIN
|
|
78
|
+
|
|
79
|
+#ifdef NUM_SERVOS
|
|
80
|
+ #define SERVO0_PIN -1
|
|
81
|
+ #if NUM_SERVOS > 1
|
|
82
|
+ #define SERVO1_PIN -1
|
|
83
|
+ #if NUM_SERVOS > 2
|
|
84
|
+ #define SERVO2_PIN 47
|
|
85
|
+ #if NUM_SERVOS > 3
|
|
86
|
+ #define SERVO3_PIN -1
|
|
87
|
+ #endif
|
|
88
|
+ #endif
|
|
89
|
+ #endif
|
|
90
|
+#endif
|