✨ Add BOARD_CREALITY_V24S1_301F4

Co-Authored-By: Miguel Risco-Castillo <mriscoc@users.noreply.github.com>

.github/workflows/test-builds.yml

@@ -76,6 +76,7 @@ jobs:
         - STM32F103RE_btt
         - STM32F103RE_btt_USB
         - STM32F103RE_creality
+        - STM32F401RC_creality
         - STM32F103VE_longer
         - STM32F407VE_black
         - STM32F401VE_STEVAL

Marlin/src/core/boards.h

@@ -418,6 +418,7 @@
 #define BOARD_MKS_EAGLE               4237  // MKS Eagle (STM32F407VE)
 #define BOARD_ARTILLERY_RUBY          4238  // Artillery Ruby (STM32F401RC)
 #define BOARD_FYSETC_SPIDER_V2_2      4239  // FYSETC Spider V2.2 (STM32F446VE)
+#define BOARD_CREALITY_V24S1_301F4    4240  // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4
 
 //
 // ARM Cortex M7

Marlin/src/inc/Conditionals_LCD.h

@@ -488,7 +488,7 @@
   #ifndef LCD_SERIAL_PORT
     #if MB(BTT_SKR_MINI_E3_V1_0, BTT_SKR_MINI_E3_V1_2, BTT_SKR_MINI_E3_V2_0, BTT_SKR_MINI_E3_V3_0, BTT_SKR_E3_TURBO)
       #define LCD_SERIAL_PORT 1
-    #elif MB(CREALITY_V24S1_301)
+    #elif MB(CREALITY_V24S1_301, CREALITY_V24S1_301F4)
       #define LCD_SERIAL_PORT 2 // Creality Ender3S1 board
     #else
       #define LCD_SERIAL_PORT 3 // Creality 4.x board

Marlin/src/libs/BL24CXX.cpp

@@ -48,7 +48,7 @@
 #ifdef __STM32F1__
   #define SDA_IN()  do{ PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH &= 0XFFFF0FFF; PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH |= 8 << 12; }while(0)
   #define SDA_OUT() do{ PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH &= 0XFFFF0FFF; PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH |= 3 << 12; }while(0)
-#elif STM32F1
+#elif defined(STM32F1) || defined(STM32F4)
   #define SDA_IN()  SET_INPUT(IIC_EEPROM_SDA)
   #define SDA_OUT() SET_OUTPUT(IIC_EEPROM_SDA)
 #endif

Marlin/src/pins/pins.h

@@ -695,6 +695,8 @@
   #include "stm32f4/pins_MKS_EAGLE.h"           // STM32F4                                env:mks_eagle
 #elif MB(ARTILLERY_RUBY)
   #include "stm32f4/pins_ARTILLERY_RUBY.h"      // STM32F4                                env:Artillery_Ruby
+#elif MB(CREALITY_V24S1_301F4)
+  #include "stm32f4/pins_CREALITY_V24S1_301F4.h" // STM32F4                               env:STM32F401RC_creality env:STM32F401RC_creality_jlink env:STM32F401RC_creality_stlink
 
 //
 // ARM Cortex M7

Marlin/src/pins/stm32f1/env_validate.h

@@ -22,5 +22,11 @@
 #pragma once
 
 #if NOT_TARGET(__STM32F1__, STM32F1)
-  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
+  #if DISABLED(ALLOW_STM32F4)
+    #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
+  #elif NOT_TARGET(STM32F4)
+    #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
+  #endif
 #endif
+
+#undef ALLOW_STM32F4

Marlin/src/pins/stm32f1/pins_CREALITY_V24S1_301.h

@@ -22,7 +22,8 @@
 #pragma once
 
 /**
- * Creality V24S1_301 (STM32F103RE / STM32F103RC) board pin assignments as found on Ender 3 S1
+ * Creality V24S1_301 (STM32F103RE / STM32F103RC) board pin assignments as found on Ender 3 S1.
+ * Also supports the STM32F4 version of the board with identical pin mapping.
  */
 
 #include "env_validate.h"
@@ -35,8 +36,12 @@
   #error "Disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN when using BLTOUCH with Creality V24S1-301."
 #endif
 
-#define BOARD_INFO_NAME      "Creality V24S1-301"
-#define DEFAULT_MACHINE_NAME "Ender 3 S1"
+#ifndef BOARD_INFO_NAME
+  #define BOARD_INFO_NAME      "Creality V24S1-301"
+#endif
+#ifndef DEFAULT_MACHINE_NAME
+  #define DEFAULT_MACHINE_NAME "Ender 3 S1"
+#endif
 
 //
 // Servos
@@ -70,8 +75,8 @@
 //
 // SD Card
 //
-#define ONBOARD_SPI_DEVICE                  1
-#define ONBOARD_SD_CS_PIN                   PA4  // SDSS
+#define ONBOARD_SPI_DEVICE                     1
+#define ONBOARD_SD_CS_PIN                   PA4   // SDSS
 
 //
 // M3/M4/M5 - Spindle/Laser Control
@@ -80,9 +85,10 @@
   //#define HEATER_0_PIN                    -1
   //#define HEATER_BED_PIN                  -1
   #define FAN_PIN                           -1
-  #define SPINDLE_LASER_ENA_PIN             PA0  // FET 1
-  #define SPINDLE_LASER_PWM_PIN             PA0  // Bed FET
-  #define SPINDLE_DIR_PIN                   PA0  // FET 4
+  #define SPINDLE_LASER_ENA_PIN             PC0   // FET 1
+  #define SPINDLE_LASER_PWM_PIN             PC0   // Bed FET
+  #define SPINDLE_DIR_PIN                   PC0   // FET 4
+  #define LASER_SOFT_PWM_PIN                PC0
 #endif
 
 #include "pins_CREALITY_V4.h"

Marlin/src/pins/stm32f1/pins_CREALITY_V4.h

@@ -43,7 +43,9 @@
 //
 // Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
 //
-#define DISABLE_DEBUG
+#ifndef DISABLE_DEBUG
+  #define DISABLE_DEBUG
+#endif
 
 //
 // EEPROM

Marlin/src/pins/stm32f4/pins_CREALITY_V24S1_301F4.h

@@ -0,0 +1,38 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * Creality V24S1_301F4 (STM32F401RC) board pin assignments as found on Ender 3 S1.
+ */
+
+#ifndef BOARD_INFO_NAME
+  #define BOARD_INFO_NAME "Creality V24S1-301F4"
+#endif
+#ifndef DEFAULT_MACHINE_NAME
+  #define DEFAULT_MACHINE_NAME "Ender-3 S1 F4"
+#endif
+
+#define DISABLE_DEBUG false // DISABLE_(DEBUG|JTAG) is not supported for STM32F4.
+#define ALLOW_STM32F4
+
+#include "../stm32f1/pins_CREALITY_V24S1_301.h"

buildroot/share/PlatformIO/boards/marlin_CREALITY_STM32F401RC.json

@@ -0,0 +1,65 @@
+{
+  "build": {
+    "core": "stm32",
+    "cpu": "cortex-m4",
+    "extra_flags": "-DSTM32F401xx",
+    "f_cpu": "84000000L",
+    "hwids": [
+      [
+        "0x1EAF",
+        "0x0003"
+      ],
+      [
+        "0x0483",
+        "0x3748"
+      ]
+    ],
+    "ldscript": "ldscript.ld",
+    "mcu": "stm32f401rct6",
+    "variant": "MARLIN_CREALITY_STM32F401RC"
+  },
+  "debug": {
+    "jlink_device": "STM32F401RC",
+    "openocd_target": "stm32f4x",
+    "svd_path": "STM32F40x.svd",
+    "tools": {
+      "stlink": {
+        "server": {
+          "arguments": [
+            "-f",
+            "scripts/interface/stlink.cfg",
+            "-c",
+            "transport select hla_swd",
+            "-f",
+            "scripts/target/stm32f4x.cfg",
+            "-c",
+            "reset_config none"
+          ],
+          "executable": "bin/openocd",
+          "package": "tool-openocd"
+        }
+      }
+    }
+  },
+  "frameworks": [
+    "arduino",
+    "stm32cube"
+  ],
+  "name": "STM32F401RC (64k RAM. 256k Flash)",
+  "upload": {
+    "disable_flushing": false,
+    "maximum_ram_size": 65536,
+    "maximum_size": 262144,
+    "protocol": "stlink",
+    "protocols": [
+      "stlink",
+      "dfu",
+      "jlink"
+    ],
+    "require_upload_port": true,
+    "use_1200bps_touch": false,
+    "wait_for_upload_port": false
+  },
+  "url": "https://www.st.com/en/microcontrollers-microprocessors/stm32f401rc.html",
+  "vendor": "Generic"
+}

buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PeripheralPins.c

@@ -0,0 +1,252 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2019, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ * Automatically generated from STM32F401R[(B-C)|(D-E)]Tx.xml
+ */
+#include "Arduino.h"
+#include "PeripheralPins.h"
+
+/* =====
+ * Note: Commented lines are alternative possibilities which are not used per default.
+ *       If you change them, you will have to know what you do
+ * =====
+ */
+
+//*** ADC ***
+
+#ifdef HAL_ADC_MODULE_ENABLED
+WEAK const PinMap PinMap_ADC[] = {
+  {PA_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
+  {PA_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
+  {PA_2,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
+  {PA_3,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
+  {PA_4,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
+  {PA_5,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
+  {PA_6,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
+  {PA_7,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
+  {PB_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
+  {PB_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
+  {PC_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
+  {PC_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
+  {PC_2,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
+  {PC_3,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
+  {PC_4,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
+  {PC_5,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
+  {NC,    NP,    0}
+};
+#endif
+
+//*** No DAC ***
+
+//*** I2C ***
+
+#ifdef HAL_I2C_MODULE_ENABLED
+WEAK const PinMap PinMap_I2C_SDA[] = {
+  {PB_3,  I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C2)},
+  {PB_4,  I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)},
+  {PB_7,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
+  {PB_9,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
+  {PC_9,  I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
+  {NC,    NP,    0}
+};
+
+WEAK const PinMap PinMap_I2C_SCL[] = {
+  {PA_8,  I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
+  {PB_6,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
+  {PB_8,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
+  {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
+  {NC,    NP,    0}
+};
+#endif
+
+//*** PWM ***
+
+#ifdef HAL_TIM_MODULE_ENABLED
+WEAK const PinMap PinMap_PWM[] = {
+  //{PA_0,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
+  {PA_0,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1
+  //{PA_1,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
+  {PA_1,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2
+  //{PA_2,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
+  {PA_2,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3
+  //{PA_2,  TIM9,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
+  //{PA_3,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
+  {PA_3,  TIM5,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4
+  //{PA_3,  TIM9,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2
+  {PA_5,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
+  {PA_6,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
+  //{PA_7,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
+  {PA_7,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
+  {PA_8,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
+  {PA_9,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
+  {PA_10, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
+  {PA_11, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
+  {PA_15, TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
+  //{PB_0,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
+  {PB_0,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
+  //{PB_1,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
+  {PB_1,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
+  {PB_3,  TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
+  {PB_4,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
+  {PB_5,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
+  {PB_6,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
+  {PB_7,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
+  {PB_8,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
+  //{PB_8,  TIM10,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1
+  {PB_9,  TIM4,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
+  //{PB_9,  TIM11,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
+  {PB_10, TIM2,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
+  {PB_13, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
+  {PB_14, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
+  {PB_15, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
+  {PC_6,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
+  {PC_7,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
+  {PC_8,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
+  {PC_9,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
+  {NC,    NP,    0}
+};
+#endif
+
+//*** SERIAL ***
+
+#ifdef HAL_UART_MODULE_ENABLED
+WEAK const PinMap PinMap_UART_TX[] = {
+  {PA_2,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
+  {PA_9,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+  {PA_11, USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+  {PB_6,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+  {PC_6,  USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+  {NC,    NP,    0}
+};
+
+WEAK const PinMap PinMap_UART_RX[] = {
+  {PA_3,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
+  {PA_10, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+  {PA_12, USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+  {PB_7,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+  {PC_7,  USART6,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+  {NC,    NP,    0}
+};
+
+WEAK const PinMap PinMap_UART_RTS[] = {
+  {PA_1,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
+  {PA_12, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+  {NC,    NP,    0}
+};
+
+WEAK const PinMap PinMap_UART_CTS[] = {
+  {PA_0,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
+  {PA_11, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+  {NC,    NP,    0}
+};
+#endif
+
+//*** SPI ***
+
+#ifdef HAL_SPI_MODULE_ENABLED
+WEAK const PinMap PinMap_SPI_MOSI[] = {
+  {PA_7,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  //{PB_5,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  {PB_5,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {PC_3,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  {NC,    NP,    0}
+};
+
+WEAK const PinMap PinMap_SPI_MISO[] = {
+  {PA_6,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  //{PB_4,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  {PB_4,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {PC_2,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  {NC,    NP,    0}
+};
+
+WEAK const PinMap PinMap_SPI_SCLK[] = {
+  {PA_5,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  //{PB_3,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  {PB_3,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  {NC,    NP,    0}
+};
+
+WEAK const PinMap PinMap_SPI_SSEL[] = {
+  {PA_4,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  //{PA_4,  SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  //{PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+  {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
+  {PB_9,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+  {NC,    NP,    0}
+};
+#endif
+
+//*** No CAN ***
+
+//*** No ETHERNET ***
+
+//*** No QUADSPI ***
+
+//*** USB ***
+
+#ifdef HAL_PCD_MODULE_ENABLED
+WEAK const PinMap PinMap_USB_OTG_FS[] = {
+#ifndef ARDUINO_CoreBoard_F401RC
+  {PA_8,  USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF
+  {PA_9,  USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS
+  {PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID
+#endif
+  {PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM
+  {PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP
+  {NC,    NP,    0}
+};
+#endif
+
+//*** No USB_OTG_HS ***
+
+//*** SD ***
+
+#ifdef HAL_SD_MODULE_ENABLED
+WEAK const PinMap PinMap_SD[] = {
+  {PB_8,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D4
+  {PB_9,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D5
+  {PC_6,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D6
+  {PC_7,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D7
+  {PC_8,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D0
+  {PC_9,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D1
+  {PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D2
+  {PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D3
+  {PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CK
+  {PD_2,  SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CMD
+  {NC,    NP,    0}
+};
+#endif

buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PinNamesVar.h

@@ -0,0 +1,33 @@
+/* SYS_WKUP */
+#ifdef PWR_WAKEUP_PIN1
+  SYS_WKUP1 = PA_0,
+#endif
+#ifdef PWR_WAKEUP_PIN2
+  SYS_WKUP2 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN3
+  SYS_WKUP3 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN4
+  SYS_WKUP4 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN5
+  SYS_WKUP5 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN6
+  SYS_WKUP6 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN7
+  SYS_WKUP7 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN8
+  SYS_WKUP8 = NC,
+#endif
+/* USB */
+#ifdef USBCON
+  USB_OTG_FS_SOF = PA_8,
+  USB_OTG_FS_VBUS = PA_9,
+  USB_OTG_FS_ID = PA_10,
+  USB_OTG_FS_DM = PA_11,
+  USB_OTG_FS_DP = PA_12,
+#endif

buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h

@@ -0,0 +1,495 @@
+/**
+  ******************************************************************************
+  * @file    stm32f4xx_hal_conf.h
+  * @brief   HAL configuration file.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_CONF_CUSTOM
+#define __STM32F4xx_HAL_CONF_CUSTOM
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+ /**
+  * @brief This is the list of modules to be used in the HAL driver
+  */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CRC_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+#define HAL_IWDG_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_CORTEX_MODULE_ENABLED
+//#define HAL_PCD_MODULE_ENABLED // Automatically added if any type of USB is enabled, as in Arduino IDE. (STM32 v3.10700.191028)
+
+//#define HAL_CAN_MODULE_ENABLED
+//#define HAL_CAN_LEGACY_MODULE_ENABLED
+//#define HAL_CEC_MODULE_ENABLED
+//#define HAL_CRYP_MODULE_ENABLED
+//#define HAL_DAC_MODULE_ENABLED
+//#define HAL_DCMI_MODULE_ENABLED
+//#define HAL_DMA2D_MODULE_ENABLED
+//#define HAL_ETH_MODULE_ENABLED
+//#define HAL_NAND_MODULE_ENABLED
+//#define HAL_NOR_MODULE_ENABLED
+//#define HAL_PCCARD_MODULE_ENABLED
+//#define HAL_SRAM_MODULE_ENABLED
+//#define HAL_SDRAM_MODULE_ENABLED
+//#define HAL_HASH_MODULE_ENABLED
+//#define HAL_EXTI_MODULE_ENABLED
+//#define HAL_SMBUS_MODULE_ENABLED
+//#define HAL_I2S_MODULE_ENABLED
+//#define HAL_LTDC_MODULE_ENABLED
+//#define HAL_DSI_MODULE_ENABLED
+//#define HAL_QSPI_MODULE_ENABLED
+//#define HAL_RNG_MODULE_ENABLED
+//#define HAL_SAI_MODULE_ENABLED
+#define HAL_SD_MODULE_ENABLED
+//#define HAL_UART_MODULE_ENABLED
+//#define HAL_USART_MODULE_ENABLED
+//#define HAL_IRDA_MODULE_ENABLED
+//#define HAL_SMARTCARD_MODULE_ENABLED
+//#define HAL_WWDG_MODULE_ENABLED
+//#define HAL_HCD_MODULE_ENABLED
+//#define HAL_FMPI2C_MODULE_ENABLED
+//#define HAL_SPDIFRX_MODULE_ENABLED
+//#define HAL_DFSDM_MODULE_ENABLED
+//#define HAL_LPTIM_MODULE_ENABLED
+//#define HAL_MMC_MODULE_ENABLED
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).
+  */
+#ifndef HSE_VALUE
+#define HSE_VALUE              8000000U /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#ifndef HSE_STARTUP_TIMEOUT
+#define HSE_STARTUP_TIMEOUT    100U      /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL).
+  */
+#ifndef HSI_VALUE
+#define HSI_VALUE              16000000U /*!< Value of the Internal oscillator in Hz */
+#endif /* HSI_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#ifndef LSI_VALUE
+#define LSI_VALUE               32000U    /*!< LSI Typical Value in Hz */
+#endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
+The real value may vary depending on the variations
+in voltage and temperature. */
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  */
+#ifndef LSE_VALUE
+#define LSE_VALUE               32768U    /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#ifndef LSE_STARTUP_TIMEOUT
+#define LSE_STARTUP_TIMEOUT    5000U     /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief External clock source for I2S peripheral
+  *        This value is used by the I2S HAL module to compute the I2S clock source
+  *        frequency, this source is inserted directly through I2S_CKIN pad.
+  */
+#ifndef EXTERNAL_CLOCK_VALUE
+#define EXTERNAL_CLOCK_VALUE     12288000U /*!< Value of the External oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */
+#if !defined (VDD_VALUE)
+#define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
+#endif
+#if !defined (TICK_INT_PRIORITY)
+#define  TICK_INT_PRIORITY            0x00U /*!< tick interrupt priority */
+#endif
+#if !defined (USE_RTOS)
+#define  USE_RTOS                     0U
+#endif
+#if !defined (PREFETCH_ENABLE)
+#define  PREFETCH_ENABLE              1U
+#endif
+#if !defined (INSTRUCTION_CACHE_ENABLE)
+#define  INSTRUCTION_CACHE_ENABLE     1U
+#endif
+#if !defined (DATA_CACHE_ENABLE)
+#define  DATA_CACHE_ENABLE            1U
+#endif
+
+#define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
+#define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
+#define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
+#define  USE_HAL_CRYP_REGISTER_CALLBACKS        0U /* CRYP register callback disabled      */
+#define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
+#define  USE_HAL_DCMI_REGISTER_CALLBACKS        0U /* DCMI register callback disabled      */
+#define  USE_HAL_DFSDM_REGISTER_CALLBACKS       0U /* DFSDM register callback disabled     */
+#define  USE_HAL_DMA2D_REGISTER_CALLBACKS       0U /* DMA2D register callback disabled     */
+#define  USE_HAL_DSI_REGISTER_CALLBACKS         0U /* DSI register callback disabled       */
+#define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
+#define  USE_HAL_HASH_REGISTER_CALLBACKS        0U /* HASH register callback disabled      */
+#define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
+#define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
+#define  USE_HAL_FMPI2C_REGISTER_CALLBACKS      0U /* FMPI2C register callback disabled    */
+#define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
+#define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
+#define  USE_HAL_LPTIM_REGISTER_CALLBACKS       0U /* LPTIM register callback disabled     */
+#define  USE_HAL_LTDC_REGISTER_CALLBACKS        0U /* LTDC register callback disabled      */
+#define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
+#define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
+#define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
+#define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
+#define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
+#define  USE_HAL_QSPI_REGISTER_CALLBACKS        0U /* QSPI register callback disabled      */
+#define  USE_HAL_RNG_REGISTER_CALLBACKS         0U /* RNG register callback disabled       */
+#define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
+#define  USE_HAL_SAI_REGISTER_CALLBACKS         0U /* SAI register callback disabled       */
+#define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
+#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
+#define  USE_HAL_SDRAM_REGISTER_CALLBACKS       0U /* SDRAM register callback disabled     */
+#define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
+#define  USE_HAL_SPDIFRX_REGISTER_CALLBACKS     0U /* SPDIFRX register callback disabled   */
+#define  USE_HAL_SMBUS_REGISTER_CALLBACKS       0U /* SMBUS register callback disabled     */
+#define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
+#define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
+#define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
+#define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
+#define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the
+  *        HAL drivers code
+  */
+/* #define USE_FULL_ASSERT    1U */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0   2U
+#define MAC_ADDR1   0U
+#define MAC_ADDR2   0U
+#define MAC_ADDR3   0U
+#define MAC_ADDR4   0U
+#define MAC_ADDR5   0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
+#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
+#define ETH_RXBUFNB                    ((uint32_t)4U)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
+#define ETH_TXBUFNB                    ((uint32_t)4U)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848_PHY_ADDRESS Address*/
+#define DP83848_PHY_ADDRESS           0x01U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY                 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY                0x00000FFFU
+
+#define PHY_READ_TO                     0x0000FFFFU
+#define PHY_WRITE_TO                    0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
+#define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
+
+#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
+#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
+#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
+#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
+#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
+#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
+#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
+
+#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
+#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
+#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
+
+/* Section 4: Extended PHY Registers */
+#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
+
+#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+ * Activated: CRC code is present inside driver
+ * Deactivated: CRC code cleaned from driver
+ */
+#ifndef USE_SPI_CRC
+#define USE_SPI_CRC                     0U
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+#include "stm32f4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+#include "stm32f4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+#include "stm32f4xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+#include "stm32f4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+#include "stm32f4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+#include "stm32f4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+#include "stm32f4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+#include "stm32f4xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+#include "stm32f4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+#include "stm32f4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+#include "stm32f4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+#include "stm32f4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+#include "stm32f4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+#include "stm32f4xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+#include "stm32f4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+#include "stm32f4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+#include "stm32f4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+#include "stm32f4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+#include "stm32f4xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+#include "stm32f4xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+#include "stm32f4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+#include "stm32f4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+#include "stm32f4xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+#include "stm32f4xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+#include "stm32f4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+#include "stm32f4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+#include "stm32f4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+#include "stm32f4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+#include "stm32f4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+#include "stm32f4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+#include "stm32f4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+#include "stm32f4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+#include "stm32f4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+#include "stm32f4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+#include "stm32f4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+#include "stm32f4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+#include "stm32f4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+#include "stm32f4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+#include "stm32f4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+#include "stm32f4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+#include "stm32f4xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+#include "stm32f4xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+#include "stm32f4xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_FMPI2C_MODULE_ENABLED
+#include "stm32f4xx_hal_fmpi2c.h"
+#endif /* HAL_FMPI2C_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+#include "stm32f4xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+#include "stm32f4xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+#include "stm32f4xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+#include "stm32f4xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+void assert_failed(uint8_t *file, uint32_t line);
+#else
+#define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_CONF_CUSTOM_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld

@@ -0,0 +1,187 @@
+/*
+*****************************************************************************
+**
+
+**  File        : LinkerScript.ld
+**
+**  Abstract    : Linker script for STM32F401RETx Device with
+**                512KByte FLASH, 96KByte RAM
+**
+**                Set heap size, stack size and stack location according
+**                to application requirements.
+**
+**                Set memory bank area and size if external memory is used.
+**
+**  Target      : STMicroelectronics STM32
+**
+**
+**  Distribution: The file is distributed as is, without any warranty
+**                of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** <h2><center>&copy; COPYRIGHT(c) 2014 Ac6</center></h2>
+**
+** Redistribution and use in source and binary forms, with or without modification,
+** are permitted provided that the following conditions are met:
+**   1. Redistributions of source code must retain the above copyright notice,
+**      this list of conditions and the following disclaimer.
+**   2. Redistributions in binary form must reproduce the above copyright notice,
+**      this list of conditions and the following disclaimer in the documentation
+**      and/or other materials provided with the distribution.
+**   3. Neither the name of Ac6 nor the names of its contributors
+**      may be used to endorse or promote products derived from this software
+**      without specific prior written permission.
+**
+** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20010000;    /* end of RAM */
+
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200;;      /* required amount of heap  */
+_Min_Stack_Size = 0x400;; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+FLASH (rx)      : ORIGIN = 0x8000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET
+RAM (xrw)      : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+/* Define output sections */
+SECTIONS
+{
+  /* The startup code goes first into FLASH */
+  .isr_vector :
+  {
+    . = ALIGN(4);
+    KEEP(*(.isr_vector)) /* Startup code */
+    . = ALIGN(4);
+  } >FLASH
+
+  /* The program code and other data goes into FLASH */
+  .text ALIGN(4):
+  {
+    . = ALIGN(4);
+    *(.text)           /* .text sections (code) */
+    *(.text*)          /* .text* sections (code) */
+    *(.glue_7)         /* glue arm to thumb code */
+    *(.glue_7t)        /* glue thumb to arm code */
+    *(.eh_frame)
+
+    KEEP (*(.init))
+    KEEP (*(.fini))
+
+    . = ALIGN(4);
+    _etext = .;        /* define a global symbols at end of code */
+  } >FLASH
+
+  /* Constant data goes into FLASH */
+  .rodata :
+  {
+    . = ALIGN(4);
+    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM.extab   : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+  .ARM : {
+    __exidx_start = .;
+    *(.ARM.exidx*)
+    __exidx_end = .;
+  } >FLASH
+
+  .preinit_array     :
+  {
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array*))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+  } >FLASH
+  .init_array :
+  {
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT(.init_array.*)))
+    KEEP (*(.init_array*))
+    PROVIDE_HIDDEN (__init_array_end = .);
+  } >FLASH
+  .fini_array :
+  {
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT(.fini_array.*)))
+    KEEP (*(.fini_array*))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+  } >FLASH
+
+  /* used by the startup to initialize data */
+  _sidata = LOADADDR(.data);
+
+  /* Initialized data sections goes into RAM, load LMA copy after code */
+  .data :
+  {
+    . = ALIGN(4);
+    _sdata = .;        /* create a global symbol at data start */
+    *(.data)           /* .data sections */
+    *(.data*)          /* .data* sections */
+
+    . = ALIGN(4);
+    _edata = .;        /* define a global symbol at data end */
+  } >RAM AT> FLASH
+
+
+  /* Uninitialized data section */
+  . = ALIGN(4);
+  .bss :
+  {
+    /* This is used by the startup in order to initialize the .bss secion */
+    _sbss = .;         /* define a global symbol at bss start */
+    __bss_start__ = _sbss;
+    *(.bss)
+    *(.bss*)
+    *(COMMON)
+
+    . = ALIGN(4);
+    _ebss = .;         /* define a global symbol at bss end */
+    __bss_end__ = _ebss;
+  } >RAM
+
+  /* User_heap_stack section, used to check that there is enough RAM left */
+  ._user_heap_stack :
+  {
+    . = ALIGN(8);
+    PROVIDE ( end = . );
+    PROVIDE ( _end = . );
+    . = . + _Min_Heap_Size;
+    . = . + _Min_Stack_Size;
+    . = ALIGN(8);
+  } >RAM
+
+
+
+  /* Remove information from the standard libraries */
+  /DISCARD/ :
+  {
+    libc.a ( * )
+    libm.a ( * )
+    libgcc.a ( * )
+  }
+
+  .ARM.attributes 0 : { *(.ARM.attributes) }
+}

buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.cpp

@@ -0,0 +1,238 @@
+/*
+  Copyright (c) 2011 Arduino.  All right reserved.
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+  See the GNU Lesser General Public License for more details.
+
+  You should have received a copy of the GNU Lesser General Public
+  License along with this library; if not, write to the Free Software
+  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#include "pins_arduino.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+// Digital PinName array
+const PinName digitalPin[] = {
+  PA_0,  // Digital pin 0
+  PA_1,  // Digital pin 1
+  PA_2,  // Digital pin 2
+  PA_3,  // Digital pin 3
+  PA_4,  // Digital pin 4
+  PA_5,  // Digital pin 5
+  PA_6,  // Digital pin 6
+  PA_7,  // Digital pin 7
+  PA_8,  // Digital pin 8
+  PA_9,  // Digital pin 9
+  PA_10, // Digital pin 10
+  PA_11, // Digital pin 11
+  PA_12, // Digital pin 12
+  PA_13, // Digital pin 13
+  PA_14, // Digital pin 14
+  PA_15, // Digital pin 15
+
+  PB_0,  // Digital pin 16
+  PB_1,  // Digital pin 17
+  PB_2,  // Digital pin 18
+  PB_3,  // Digital pin 19
+  PB_4,  // Digital pin 20
+  PB_5,  // Digital pin 21
+  PB_6,  // Digital pin 22
+  PB_7,  // Digital pin 23
+  PB_8,  // Digital pin 24
+  PB_9,  // Digital pin 25
+  PB_10, // Digital pin 26
+  PB_12, // Digital pin 27
+  PB_13, // Digital pin 28
+  PB_14, // Digital pin 29
+  PB_15, // Digital pin 30
+
+  PC_0,  // Digital pin 31
+  PC_1,  // Digital pin 32
+  PC_2,  // Digital pin 33
+  PC_3,  // Digital pin 34
+  PC_4,  // Digital pin 35
+  PC_5,  // Digital pin 36
+  PC_6,  // Digital pin 37
+  PC_7,  // Digital pin 38
+  PC_8,  // Digital pin 39
+  PC_9,  // Digital pin 40
+  PC_10, // Digital pin 41
+  PC_11, // Digital pin 42
+  PC_12, // Digital pin 43
+  PC_13, // Digital pin 44
+  PC_14, // Digital pin 45
+  PC_15, // Digital pin 46
+
+  PD_2,  // Digital pin 47
+
+  PH_0,  // Digital pin 48, used by the external oscillator
+  PH_1   // Digital pin 49, used by the external oscillator
+};
+
+// Analog (Ax) pin number array
+const uint32_t analogInputPin[] = {
+  0,  // A0,  PA0
+  1,  // A1,  PA1
+  2,  // A2,  PA2
+  3,  // A3,  PA3
+  4,  // A4,  PA4
+  5,  // A5,  PA5
+  6,  // A6,  PA6
+  7,  // A7,  PA7
+  16, // A8,  PB0
+  17, // A9,  PB1
+  31, // A10, PC0
+  32, // A11, PC1
+  33, // A12, PC2
+  34, // A13, PC3
+  35, // A14, PC4
+  36  // A15, PC5
+};
+
+#ifdef __cplusplus
+}
+#endif
+
+// ----------------------------------------------------------------------------
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/*
+ * @brief  Configures the System clock source, PLL Multiplier and Divider factors,
+ *               AHB/APBx prescalers and Flash settings
+ * @note   This function should be called only once the RCC clock configuration
+ *         is reset to the default reset state (done in SystemInit() function).
+ * @param  None
+ * @retval None
+ */
+
+/******************************************************************************/
+/*            PLL (clocked by HSE) used as System clock source                */
+/******************************************************************************/
+static uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct;
+  RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+  /* The voltage scaling allows optimizing the power consumption when the device is
+  clocked below the maximum system frequency, to update the voltage scaling value
+  regarding system frequency refer to product datasheet. */
+  __HAL_RCC_PWR_CLK_ENABLE();
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+  // Enable HSE oscillator and activate PLL with HSE as source
+  RCC_OscInitStruct.OscillatorType      = RCC_OSCILLATORTYPE_HSE;
+  if (bypass == 0) {
+    RCC_OscInitStruct.HSEState          = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+  } else {
+    RCC_OscInitStruct.HSEState          = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+  }
+
+  RCC_OscInitStruct.PLL.PLLState        = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource       = RCC_PLLSOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLM            = HSE_VALUE / 1000000L; // Expects an 8 MHz external clock by default. Redefine HSE_VALUE if not
+  RCC_OscInitStruct.PLL.PLLN            = 336;           // VCO output clock = 336 MHz (1 MHz * 336)
+  RCC_OscInitStruct.PLL.PLLP            = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
+  RCC_OscInitStruct.PLL.PLLQ            = 7;             // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+    return 0; // FAIL
+  }
+
+  // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.SYSCLKSource   = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
+  RCC_ClkInitStruct.AHBCLKDivider  = RCC_SYSCLK_DIV1;         // 84 MHz
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;           // 42 MHz
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;           // 84 MHz
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {
+    return 0; // FAIL
+  }
+
+  /* Output clock on MCO1 pin(PA8) for debugging purpose */
+  /*
+  if (bypass == 0)
+    HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
+  else
+    HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
+  */
+
+  return 1; // OK
+}
+
+/******************************************************************************/
+/*            PLL (clocked by HSI) used as System clock source                */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct;
+  RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+  /* The voltage scaling allows optimizing the power consumption when the device is
+    clocked below the maximum system frequency, to update the voltage scaling value
+    regarding system frequency refer to product datasheet. */
+  __HAL_RCC_PWR_CLK_ENABLE();
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+  // Enable HSI oscillator and activate PLL with HSI as source
+  RCC_OscInitStruct.OscillatorType      = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSIState            = RCC_HSI_ON;
+  RCC_OscInitStruct.HSEState            = RCC_HSE_OFF;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.PLL.PLLState        = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource       = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLM            = 16;            // VCO input clock = 1 MHz (16 MHz / 16)
+  RCC_OscInitStruct.PLL.PLLN            = 336;           // VCO output clock = 336 MHz (1 MHz * 336)
+  RCC_OscInitStruct.PLL.PLLP            = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
+  RCC_OscInitStruct.PLL.PLLQ            = 7;             // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+    return 0; // FAIL
+  }
+
+  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+  RCC_ClkInitStruct.ClockType      = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+  RCC_ClkInitStruct.SYSCLKSource   = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
+  RCC_ClkInitStruct.AHBCLKDivider  = RCC_SYSCLK_DIV1;         // 84 MHz
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;           // 42 MHz
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;           // 84 MHz
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {
+    return 0; // FAIL
+  }
+
+  /* Output clock on MCO1 pin(PA8) for debugging purpose */
+  //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+  return 1; // OK
+}
+
+WEAK void SystemClock_Config(void)
+{
+  /* 1- If fail try to start with HSE and external xtal */
+  if (SetSysClock_PLL_HSE(0) == 0) {
+    /* 2- Try to start with HSE and external clock */
+    if (SetSysClock_PLL_HSE(1) == 0) {
+      /* 3- If fail start with HSI clock */
+      if (SetSysClock_PLL_HSI() == 0) {
+        Error_Handler();
+      }
+    }
+  }
+  /* Output clock on MCO2 pin(PC9) for debugging purpose */
+  //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+}
+
+#ifdef __cplusplus
+}
+#endif

buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.h

@@ -0,0 +1,151 @@
+/*
+  Copyright (c) 2011 Arduino.  All right reserved.
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+  See the GNU Lesser General Public License for more details.
+
+  You should have received a copy of the GNU Lesser General Public
+  License along with this library; if not, write to the Free Software
+  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#ifndef _VARIANT_ARDUINO_STM32_
+#define _VARIANT_ARDUINO_STM32_
+
+#ifdef __cplusplus
+extern "C" {
+#endif // __cplusplus
+
+
+//                  | DIGITAL | ANALOG | USART     | TWI      | SPI                    | SPECIAL   |
+//                  |---------|--------|-----------|----------|------------------------|-----------|
+#define PA0  0   // | 0       | A0     |           |          |                        |           |
+#define PA1  1   // | 1       | A1     |           |          |                        |           |
+#define PA2  2   // | 2       | A2     | USART2_TX |          |                        |           |
+#define PA3  3   // | 3       | A3     | USART2_RX |          |                        |           |
+#define PA4  4   // | 4       | A4     |           |          | SPI1_SS, (SPI3_SS)     |           |
+#define PA5  5   // | 5       | A5     |           |          | SPI1_SCK               |           |
+#define PA6  6   // | 6       | A6     |           |          | SPI1_MISO              |           |
+#define PA7  7   // | 7       | A7     |           |          | SPI1_MOSI              |           |
+#define PA8  8   // | 8       |        |           | TWI3_SCL |                        |           |
+#define PA9  9   // | 9       |        | USART1_TX |          |                        |           |
+#define PA10 10  // | 10      |        | USART1_RX |          |                        |           |
+#define PA11 11  // | 11      |        | USART6_TX |          |                        |           |
+#define PA12 12  // | 12      |        | USART6_RX |          |                        |           |
+#define PA13 13  // | 13      |        |           |          |                        | SWD_SWDIO |
+#define PA14 14  // | 14      |        |           |          |                        | SWD_SWCLK |
+#define PA15 15  // | 15      |        |           |          | SPI3_SS, (SPI1_SS)     |           |
+//                  |---------|--------|-----------|----------|------------------------|-----------|
+#define PB0  16  // | 16      | A8     |           |          |                        |           |
+#define PB1  17  // | 17      | A9     |           |          |                        |           |
+#define PB2  18  // | 18      |        |           |          |                        | BOOT1     |
+#define PB3  19  // | 19      |        |           | TWI2_SDA | SPI3_SCK,  (SPI1_SCK)  |           |
+#define PB4  20  // | 20      |        |           | TWI3_SDA | SPI3_MISO, (SPI1_MISO) |           |
+#define PB5  21  // | 21      |        |           |          | SPI3_MOSI, (SPI1_MOSI) |           |
+#define PB6  22  // | 22      |        | USART1_TX | TWI1_SCL |                        |           |
+#define PB7  23  // | 23      |        | USART1_RX | TWI1_SDA |                        |           |
+#define PB8  24  // | 24      |        |           | TWI1_SCL |                        |           |
+#define PB9  25  // | 25      |        |           | TWI1_SDA | SPI2_SS                |           |
+#define PB10 26  // | 26      |        |           | TWI2_SCL | SPI2_SCK               |           |
+#define PB12 27  // | 27      |        |           |          | SPI2_SS                |           |
+#define PB13 28  // | 28      |        |           |          | SPI2_SCK               |           |
+#define PB14 29  // | 29      |        |           |          | SPI2_MISO              |           |
+#define PB15 30  // | 30      |        |           |          | SPI2_MOSI              |           |
+//                  |---------|--------|-----------|----------|------------------------|-----------|
+#define PC0  31  // | 31      | A10    |           |          |                        |           |
+#define PC1  32  // | 32      | A11    |           |          |                        |           |
+#define PC2  33  // | 33      | A12    |           |          | SPI2_MISO              |           |
+#define PC3  34  // | 34      | A13    |           |          | SPI2_MOSI              |           |
+#define PC4  35  // | 35      | A14    |           |          |                        |           |
+#define PC5  36  // | 36      | A15    |           |          |                        |           |
+#define PC6  37  // | 37      |        | USART6_TX |          |                        |           |
+#define PC7  38  // | 38      |        | USART6_RX |          |                        |           |
+#define PC8  39  // | 39      |        |           |          |                        |           |
+#define PC9  40  // | 40      |        |           | TWI3_SDA |                        |           |
+#define PC10 41  // | 41      |        |           |          | SPI3_SCK               |           |
+#define PC11 42  // | 42      |        |           |          | SPI3_MISO              |           |
+#define PC12 43  // | 43      |        |           |          | SPI3_MOSI              |           |
+#define PC13 44  // | 44      |        |           |          |                        |           |
+#define PC14 45  // | 45      |        |           |          |                        | OSC32_IN  |
+#define PC15 46  // | 46      |        |           |          |                        | OSC32_OUT |
+//                  |---------|--------|-----------|----------|------------------------|-----------|
+#define PD2  47  // | 47      |        |           |          |                        |           |
+//                  |---------|--------|-----------|----------|------------------------|-----------|
+#define PH0  48  // | 48      |        |           |          |                        | OSC_IN    |
+#define PH1  49  // | 49      |        |           |          |                        | OSC_OUT   |
+//                  |---------|--------|-----------|----------|------------------------|-----------|
+
+// This must be a literal
+#define NUM_DIGITAL_PINS        50
+#define NUM_ANALOG_INPUTS       16
+
+// SPI definitions
+#define PIN_SPI_SS              PA4
+#define PIN_SPI_SS1             PA4
+#define PIN_SPI_MOSI            PA7
+#define PIN_SPI_MISO            PA6
+#define PIN_SPI_SCK             PA5
+
+
+// Timer Definitions
+#define TIMER_TONE              TIM2
+#define TIMER_SERVO             TIM5
+#define TIMER_SERIAL            TIM11
+
+// UART Definitions
+//#define ENABLE_HWSERIAL1        done automatically by the #define SERIAL_UART_INSTANCE below
+#define ENABLE_HWSERIAL2
+
+
+// Define here Serial instance number to map on Serial generic name (if not already used by SerialUSB)
+#define SERIAL_UART_INSTANCE    1 //1 for Serial = Serial1 (USART1)
+
+// Default pin used for 'Serial' instance
+// Mandatory for Firmata
+#define PIN_SERIAL_RX           PA10
+#define PIN_SERIAL_TX           PA9
+
+// Used when user instanciate a hardware Serial using its peripheral name.
+// Example: HardwareSerial mySerial(USART3);
+// will use PIN_SERIAL3_RX and PIN_SERIAL3_TX if defined.
+#define PIN_SERIAL1_RX          PA10
+#define PIN_SERIAL1_TX          PA9
+#define PIN_SERIAL2_RX          PA3
+#define PIN_SERIAL2_TX          PA2
+
+#ifdef __cplusplus
+} // extern "C"
+#endif
+/*----------------------------------------------------------------------------
+ *        Arduino objects - C++ only
+ *----------------------------------------------------------------------------*/
+
+#ifdef __cplusplus
+  // These serial port names are intended to allow libraries and architecture-neutral
+  // sketches to automatically default to the correct port name for a particular type
+  // of use.  For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
+  // the first hardware serial port whose RX/TX pins are not dedicated to another use.
+  //
+  // SERIAL_PORT_MONITOR        Port which normally prints to the Arduino Serial Monitor
+  //
+  // SERIAL_PORT_USBVIRTUAL     Port which is USB virtual serial
+  //
+  // SERIAL_PORT_LINUXBRIDGE    Port which connects to a Linux system via Bridge library
+  //
+  // SERIAL_PORT_HARDWARE       Hardware serial port, physical RX & TX pins.
+  //
+  // SERIAL_PORT_HARDWARE_OPEN  Hardware serial ports which are open for use.  Their RX & TX
+  //                            pins are NOT connected to anything by default.
+  #define SERIAL_PORT_MONITOR         Serial
+  #define SERIAL_PORT_HARDWARE        Serial1
+  #define SERIAL_PORT_HARDWARE_OPEN   Serial2
+#endif
+
+#endif /* _VARIANT_ARDUINO_STM32_ */

buildroot/tests/STM32F103RE_creality

@@ -15,12 +15,6 @@ exec_test $1 $2 "Ender 3 v2 with CrealityUI" "$3"
 
 use_example_configs "Creality/Ender-3 V2/CrealityV422/CrealityUI"
 opt_disable DWIN_CREALITY_LCD
-opt_enable BLTOUCH AUTO_BED_LEVELING_UBL Z_SAFE_HOMING INDIVIDUAL_AXIS_HOMING_SUBMENU LCD_SET_PROGRESS_MANUALLY STATUS_MESSAGE_SCROLLING BAUD_RATE_GCODE \
-           DWIN_LCD_PROUI SOUND_MENU_ITEM PRINTCOUNTER
-exec_test $1 $2 "Ender 3 v2 with ProUI" "$3"
-
-use_example_configs "Creality/Ender-3 V2/CrealityV422/CrealityUI"
-opt_disable DWIN_CREALITY_LCD
 opt_enable DWIN_CREALITY_LCD_JYERSUI AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY
 exec_test $1 $2 "Ender 3 v2 with JyersUI" "$3"
 

buildroot/tests/STM32F401RC_creality

@@ -0,0 +1,20 @@
+#!/usr/bin/env bash
+#
+# Build tests for STM32F401RC_creality
+#
+
+# exit on first failure
+set -e
+
+use_example_configs "Creality/Ender-3 S1"
+opt_disable DWIN_CREALITY_LCD Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN AUTO_BED_LEVELING_BILINEAR CONFIGURATION_EMBEDDING CANCEL_OBJECTS FWRETRACT
+opt_enable DWIN_LCD_PROUI INDIVIDUAL_AXIS_HOMING_SUBMENU LCD_SET_PROGRESS_MANUALLY STATUS_MESSAGE_SCROLLING \
+           SOUND_MENU_ITEM PRINTCOUNTER NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE FILAMENT_RUNOUT_SENSOR \
+           BLTOUCH Z_SAFE_HOMING AUTO_BED_LEVELING_UBL MESH_EDIT_MENU \
+           LIMITED_MAX_FR_EDITING LIMITED_MAX_ACCEL_EDITING LIMITED_JERK_EDITING BAUD_RATE_GCODE
+opt_set MOTHERBOARD BOARD_CREALITY_V24S1_301F4 \
+        PREHEAT_3_LABEL '"CUSTOM"' PREHEAT_3_TEMP_HOTEND 240 PREHEAT_3_TEMP_BED 60 PREHEAT_3_FAN_SPEED 128
+exec_test $1 $2 "Ender-3 S1 with ProUI" "$3"
+
+# clean up
+restore_configs

ini/stm32f4.ini

@@ -588,4 +588,31 @@ build_flags       = ${common_stm32.build_flags}
                     -DUSB_PRODUCT=\"Artillery_3D_Printer\"
                     -DFLASH_DATA_SECTOR=1U -DFLASH_BASE_ADDRESS=0x08004000
 extra_scripts     = ${common_stm32.extra_scripts}
-  pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py
+                    pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py
+
+#
+# Ender-3 S1 STM32F401RC_creality
+#
+[env:STM32F401RC_creality]
+extends                     = stm32_variant
+board                       = genericSTM32F401RC
+board_build.variant         = MARLIN_CREALITY_STM32F401RC
+board_build.offset          = 0x10000
+board_upload.offset_address = 0x08010000
+build_flags                 = ${stm32_variant.build_flags} -DMCU_STM32F401RC -DSTM32F4
+                              -DSS_TIMER=4 -DTIMER_SERVO=TIM5
+                              -DENABLE_HWSERIAL3 -DTRANSFER_CLOCK_DIV=8
+build_unflags               = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC
+extra_scripts               = ${stm32_variant.extra_scripts}
+                              pre:buildroot/share/PlatformIO/scripts/random-bin.py
+monitor_speed               = 115200
+
+[env:STM32F401RC_creality_jlink]
+extends                     = env:STM32F401RC_creality
+debug_tool                  = jlink
+upload_protocol             = jlink
+
+[env:STM32F401RC_creality_stlink]
+extends                     = env:STM32F401RC_creality
+debug_tool                  = stlink
+upload_protocol             = stlink