Update configs for new servo deactivation

Marlin/Configuration.h

@@ -767,17 +767,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// If DEACTIVATE_SERVOS_AFTER_MOVE is defined, the servos will be turned on only during movement and then turned off to avoid jitter
-// SERVO_DEACTIVATION_DELAY is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-// If your servo does not reach the requested position, enlarge the time.
-// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-//
-//#define DEACTIVATE_SERVOS_AFTER_MOVE
-
-#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
-  #define SERVO_DEACTIVATION_DELAY 300
-#endif
-
 // Servo Endstops
 //
 // This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
@@ -786,6 +775,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/SanityCheck.h

@@ -85,6 +85,13 @@
   #endif
 
   /**
+   * Servo deactivation depends on servo endstops
+   */
+  #if defined(DEACTIVATE_SERVOS_AFTER_MOVE) && !defined(SERVO_ENDSTOPS)
+    #error SERVO_ENDSTOPS is required for DEACTIVATE_SERVOS_AFTER_MOVE.
+  #endif
+
+  /**
    * Required LCD language
    */
   #if !defined(DOGLCD) && defined(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780_JAPAN) && !defined(DISPLAY_CHARSET_HD44780_WESTERN)&& !defined(DISPLAY_CHARSET_HD44780_CYRILLIC)

Marlin/configurator/config/Configuration.h

@@ -503,13 +503,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -781,6 +774,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/Felix/Configuration.h

@@ -486,13 +486,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -765,6 +758,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/Hephestos/Configuration.h

@@ -512,13 +512,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -790,6 +783,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/K8200/Configuration.h

@@ -520,13 +520,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -798,6 +791,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -504,13 +504,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -782,6 +775,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/RigidBot/Configuration.h

@@ -503,13 +503,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -782,6 +775,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/SCARA/Configuration.h

@@ -545,13 +545,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -823,6 +816,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/WITBOX/Configuration.h

@@ -512,13 +512,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -790,6 +783,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -503,13 +503,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -781,6 +774,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -624,13 +624,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
     #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_Z
   #endif
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -909,6 +902,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/delta/generic/Configuration.h

@@ -624,13 +624,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
     //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_Z
   #endif
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -909,6 +902,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -628,13 +628,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
     //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_Z
   #endif
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -913,6 +906,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -641,13 +641,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
     #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_Z
   #endif
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -936,6 +929,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/makibox/Configuration.h

@@ -507,13 +507,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -785,6 +778,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -509,13 +509,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
 //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
 //it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
@@ -791,6 +784,18 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
+  // Delay (in microseconds) before turning the servo off. This depends on the servo speed.
+  // 300ms is a good value but you can try less delay.
+  // If the servo can't reach the requested position, increase it.
+  #define SERVO_DEACTIVATION_DELAY 300
+#endif
+
 /**********************************************************************\
  * Support for a filament diameter sensor
  * Also allows adjustment of diameter at print time (vs  at slicing)

Marlin/servo.cpp

@@ -35,8 +35,8 @@
 
  write()     - Sets the servo angle in degrees.  (invalid angle that is valid as pulse in microseconds is treated as microseconds)
  writeMicroseconds() - Sets the servo pulse width in microseconds
- move(pin, angel) - Sequence of attach(pin), write(angel),
-                    if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.
+ move(pin, angel) - Sequence of attach(pin), write(angel).
+                    With DEACTIVATE_SERVOS_AFTER_MOVE it waits SERVO_DEACTIVATION_DELAY and detaches.
  read()      - Gets the last written servo pulse width as an angle between 0 and 180.
  readMicroseconds()   - Gets the last written servo pulse width in microseconds. (was read_us() in first release)
  attached()  - Returns true if there is a servo attached.

Marlin/servo.h

@@ -41,7 +41,7 @@
    attached()  - Returns true if there is a servo attached.
    detach()    - Stops an attached servos from pulsing its i/o pin.
    move(pin, angel) - Sequence of attach(pin), write(angel),
-                      if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.
+                      With DEACTIVATE_SERVOS_AFTER_MOVE it waits SERVO_DEACTIVATION_DELAY and detaches.
  */
 
 #ifndef servo_h