Fix issues #1248, #1240

- Fixed issue when BAL area probing is shorter than it should be for
grid probing
- Warning when BAL activated with Delta Kinematics
- Fix XY_TRAVEL_SPEED when homing Z axis

Marlin/Configuration.h

@@ -431,6 +431,29 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif
 
+  #ifdef AUTO_BED_LEVELING_GRID	// Check if Probe_Offset * Grid Points is greater than Probing Range
+    #if X_PROBE_OFFSET_FROM_EXTRUDER < 0
+      #if (-(X_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
+	     #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#else
+      #if ((X_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
+	     #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#endif
+    #if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
+      #if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
+	     #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#else
+      #if ((Y_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
+	     #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#endif
+
+	
+  #endif
+  
 #endif // ENABLE_AUTO_BED_LEVELING
 
 

Marlin/Configuration_adv.h

@@ -455,6 +455,11 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 //===========================================================================
 //=============================  Define Defines  ============================
 //===========================================================================
+
+#if defined (ENABLE_AUTO_BED_LEVELING) && defined (DELTA)
+  #error "Bed Auto Leveling is still not compatible with Delta Kinematics."
+#endif
+
 #if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
   #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
 #endif

Marlin/Marlin_main.cpp

@@ -1571,7 +1571,7 @@ void process_commands()
             destination[X_AXIS] = round(Z_SAFE_HOMING_X_POINT - X_PROBE_OFFSET_FROM_EXTRUDER);
             destination[Y_AXIS] = round(Z_SAFE_HOMING_Y_POINT - Y_PROBE_OFFSET_FROM_EXTRUDER);
             destination[Z_AXIS] = Z_RAISE_BEFORE_HOMING * home_dir(Z_AXIS) * (-1);    // Set destination away from bed
-            feedrate = XY_TRAVEL_SPEED;
+            feedrate = XY_TRAVEL_SPEED/60;
             current_position[Z_AXIS] = 0;
 
             plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);

Marlin/example_configurations/delta/Configuration.h

@@ -281,9 +281,6 @@ your extruder heater takes 2 minutes to hit the target on heating.
 //=============================Mechanical Settings===========================
 //===========================================================================
 
-// Uncomment the following line to enable CoreXY kinematics
-// #define COREXY
-
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -364,97 +361,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
 //============================= Bed Auto Leveling ===========================
+//Bed Auto Leveling is still not compatible with Delta Kinematics
 
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
-#define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-
-#ifdef ENABLE_AUTO_BED_LEVELING
-
-// There are 2 different ways to pick the X and Y locations to probe:
-
-//  - "grid" mode
-//    Probe every point in a rectangular grid
-//    You must specify the rectangle, and the density of sample points
-//    This mode is preferred because there are more measurements.
-//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
-
-//  - "3-point" mode
-//    Probe 3 arbitrary points on the bed (that aren't colinear)
-//    You must specify the X & Y coordinates of all 3 points
-
-  #define AUTO_BED_LEVELING_GRID
-  // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
-  // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
-  // and least squares solution is calculated
-  // Note: this feature occupies 10'206 byte
-  #ifdef AUTO_BED_LEVELING_GRID
-
-    // set the rectangle in which to probe
-    #define LEFT_PROBE_BED_POSITION 15
-    #define RIGHT_PROBE_BED_POSITION 170
-    #define BACK_PROBE_BED_POSITION 180
-    #define FRONT_PROBE_BED_POSITION 20
-
-     // set the number of grid points per dimension
-     // I wouldn't see a reason to go above 3 (=9 probing points on the bed)
-    #define AUTO_BED_LEVELING_GRID_POINTS 2
-
-
-  #else  // not AUTO_BED_LEVELING_GRID
-    // with no grid, just probe 3 arbitrary points.  A simple cross-product
-    // is used to esimate the plane of the print bed
-
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
-
-  #endif // AUTO_BED_LEVELING_GRID
-
-
-  // these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29
-  #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
-
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case
-
-  #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min
-
-  #define Z_RAISE_BEFORE_PROBING 15    //How much the extruder will be raised before traveling to the first probing point.
-  #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
-
-  //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
-  //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
-
-  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
-  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
-  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
-
-//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
-
-
-//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
-//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
-
-  #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with probe outside the bed area.
-                          // When defined, it will:
-                          // - Allow Z homing only after X and Y homing AND stepper drivers still enabled
-                          // - If stepper drivers timeout, it will need X and Y homing again before Z homing
-                          // - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
-                          // - Block Z homing only when the probe is outside bed area.
-
-  #ifdef Z_SAFE_HOMING
-
-    #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2)    // X point for Z homing when homing all axis (G28)
-    #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2)    // Y point for Z homing when homing all axis (G28)
-
-  #endif
 
-#endif // ENABLE_AUTO_BED_LEVELING
 
 
 // The position of the homing switches

Marlin/example_configurations/delta/Configuration_adv.h

@@ -450,6 +450,11 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 //===========================================================================
 //=============================  Define Defines  ============================
 //===========================================================================
+
+#if defined (ENABLE_AUTO_BED_LEVELING) && defined (DELTA)
+  #error "Bed Auto Leveling is still not compatible with Delta Kinematics."
+#endif  
+
 #if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
   #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
 #endif