Change XY_PROBE_SPEED format to (x*60) (#18997)

Marlin/Configuration.h

@@ -235,8 +235,8 @@
 
   #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
 
-    #define MPE_FAST_SPEED      9000      // (mm/m) Speed for travel before last distance point
-    #define MPE_SLOW_SPEED      4500      // (mm/m) Speed for last distance travel to park and couple
+    #define MPE_FAST_SPEED      9000      // (mm/min) Speed for travel before last distance point
+    #define MPE_SLOW_SPEED      4500      // (mm/min) Speed for last distance travel to park and couple
     #define MPE_TRAVEL_DISTANCE   10      // (mm) Last distance point
     #define MPE_COMPENSATION       0      // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
 
@@ -284,8 +284,8 @@
     #if ENABLED(PRIME_BEFORE_REMOVE)
       #define SWITCHING_TOOLHEAD_PRIME_MM           20  // (mm)   Extruder prime length
       #define SWITCHING_TOOLHEAD_RETRACT_MM         10  // (mm)   Retract after priming length
-      #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE    300  // (mm/m) Extruder prime feedrate
-      #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400  // (mm/m) Extruder retract feedrate
+      #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE    300  // (mm/min) Extruder prime feedrate
+      #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400  // (mm/min) Extruder retract feedrate
     #endif
   #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
     #define SWITCHING_TOOLHEAD_Z_HOP          2         // (mm) Z raise for switching
@@ -999,13 +999,13 @@
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
 #define PROBING_MARGIN 10
 
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 8000
+// X and Y axis travel speed (mm/min) between probes
+#define XY_PROBE_SPEED (133*60)
 
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+// Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
-// Feedrate (mm/m) for the "accurate" probe of each point
+// Feedrate (mm/min) for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
 /**
@@ -1399,7 +1399,7 @@
   #define Z_SAFE_HOMING_Y_POINT Y_CENTER  // Y point for Z homing
 #endif
 
-// Homing speeds (mm/m)
+// Homing speeds (mm/min)
 #define HOMING_FEEDRATE_XY (50*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 

Marlin/Configuration_adv.h

@@ -339,7 +339,7 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/min)
   #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
@@ -883,7 +883,7 @@
       // increments while checking for the contact to be broken.
       #define BACKLASH_MEASUREMENT_LIMIT       0.5   // (mm)
       #define BACKLASH_MEASUREMENT_RESOLUTION  0.005 // (mm)
-      #define BACKLASH_MEASUREMENT_FEEDRATE    Z_PROBE_SPEED_SLOW // (mm/m)
+      #define BACKLASH_MEASUREMENT_FEEDRATE    Z_PROBE_SPEED_SLOW // (mm/min)
     #endif
   #endif
 #endif
@@ -1025,7 +1025,7 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // (mm/m) Feedrates for manual moves along X, Y, Z, E from panel
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // (mm/min) Feedrates for manual moves along X, Y, Z, E from panel
   #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
@@ -1985,13 +1985,13 @@
     // Load / Unload
     #define TOOLCHANGE_FS_LENGTH              12  // (mm) Load / Unload length
     #define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH  0  // (mm) Extra length for better restart, fine tune by LCD/Gcode)
-    #define TOOLCHANGE_FS_RETRACT_SPEED   (50*60) // (mm/m) (Unloading)
-    #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/m) (On SINGLENOZZLE or Bowden loading must be slowed down)
+    #define TOOLCHANGE_FS_RETRACT_SPEED   (50*60) // (mm/min) (Unloading)
+    #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/min) (On SINGLENOZZLE or Bowden loading must be slowed down)
 
     // Longer prime to clean out a SINGLENOZZLE
     #define TOOLCHANGE_FS_EXTRA_PRIME          0  // (mm) Extra priming length
-    #define TOOLCHANGE_FS_PRIME_SPEED    (4.6*60) // (mm/m) Extra priming feedrate
-    #define TOOLCHANGE_FS_WIPE_RETRACT         0  // (mm/m) Retract before cooling for less stringing, better wipe, etc.
+    #define TOOLCHANGE_FS_PRIME_SPEED    (4.6*60) // (mm/min) Extra priming feedrate
+    #define TOOLCHANGE_FS_WIPE_RETRACT         0  // (mm/min) Retract before cooling for less stringing, better wipe, etc.
 
     // Cool after prime to reduce stringing
     #define TOOLCHANGE_FS_FAN                 -1  // Fan index or -1 to skip
@@ -2027,7 +2027,7 @@
   //#define TOOLCHANGE_PARK
   #if ENABLED(TOOLCHANGE_PARK)
     #define TOOLCHANGE_PARK_XY    { X_MIN_POS + 10, Y_MIN_POS + 10 }
-    #define TOOLCHANGE_PARK_XY_FEEDRATE 6000  // (mm/m)
+    #define TOOLCHANGE_PARK_XY_FEEDRATE 6000  // (mm/min)
     //#define TOOLCHANGE_PARK_X_ONLY          // X axis only move
     //#define TOOLCHANGE_PARK_Y_ONLY          // Y axis only move
   #endif
@@ -3151,7 +3151,7 @@
 //#define GCODE_MOTION_MODES  // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
 
 // Enable and set a (default) feedrate for all G0 moves
-//#define G0_FEEDRATE 3000 // (mm/m)
+//#define G0_FEEDRATE 3000 // (mm/min)
 #ifdef G0_FEEDRATE
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
@@ -3468,7 +3468,7 @@
   #if ENABLED(PRUSA_MMU2_S_MODE)
     #define MMU2_C0_RETRY   5             // Number of retries (total time = timeout*retries)
 
-    #define MMU2_CAN_LOAD_FEEDRATE 800    // (mm/m)
+    #define MMU2_CAN_LOAD_FEEDRATE 800    // (mm/min)
     #define MMU2_CAN_LOAD_SEQUENCE \
       {  0.1, MMU2_CAN_LOAD_FEEDRATE }, \
       {  60.0, MMU2_CAN_LOAD_FEEDRATE }, \