Fix some THERMAL_PROTECTION_CHAMBER issues (#13678)

Marlin/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

Marlin/src/gcode/host/M115.cpp

@@ -152,7 +152,7 @@ void GcodeSuite::M115() {
 
     // THERMAL_PROTECTION
     cap_line(PSTR("THERMAL_PROTECTION")
-      #if BOTH(THERMAL_PROTECTION_HOTENDS, THERMAL_PROTECTION_BED)
+      #if ENABLED(THERMAL_PROTECTION_HOTENDS) && (ENABLED(THERMAL_PROTECTION_BED) || !HAS_HEATED_BED) && (ENABLED(THERMAL_PROTECTION_CHAMBER) || !HAS_HEATED_CHAMBER)
         , true
       #endif
     );

Marlin/src/module/temperature.cpp

@@ -233,8 +233,8 @@ hotend_info_t Temperature::temp_hotend[HOTENDS]; // = { 0 }
     #endif
     #if WATCH_CHAMBER
       heater_watch_t Temperature::watch_chamber = { 0 };
-      millis_t Temperature::next_chamber_check_ms;
     #endif
+    millis_t Temperature::next_chamber_check_ms;
   #endif // HAS_HEATED_CHAMBER
 #endif // HAS_TEMP_CHAMBER
 
@@ -1058,56 +1058,61 @@ void Temperature::manage_heater() {
       }
     #endif // WATCH_BED
 
-    #if DISABLED(PIDTEMPBED)
-      if (PENDING(ms, next_bed_check_ms)
+    do {
+
+      #if DISABLED(PIDTEMPBED)
+        if (PENDING(ms, next_bed_check_ms)
+          #if BOTH(PROBING_HEATERS_OFF, BED_LIMIT_SWITCHING)
+            && paused == last_pause_state
+          #endif
+        ) break;
+        next_bed_check_ms = ms + BED_CHECK_INTERVAL;
         #if BOTH(PROBING_HEATERS_OFF, BED_LIMIT_SWITCHING)
-          && paused == last_pause_state
+          last_pause_state = paused;
         #endif
-      ) return;
-      next_bed_check_ms = ms + BED_CHECK_INTERVAL;
-      #if BOTH(PROBING_HEATERS_OFF, BED_LIMIT_SWITCHING)
-        last_pause_state = paused;
       #endif
-    #endif
 
-    #if HEATER_IDLE_HANDLER
-      bed_idle.update(ms);
-    #endif
+      #if HEATER_IDLE_HANDLER
+        bed_idle.update(ms);
+      #endif
 
-    #if HAS_THERMALLY_PROTECTED_BED
-      thermal_runaway_protection(tr_state_machine_bed, temp_bed.current, temp_bed.target, -1, THERMAL_PROTECTION_BED_PERIOD, THERMAL_PROTECTION_BED_HYSTERESIS);
-    #endif
+      #if HAS_THERMALLY_PROTECTED_BED
+        thermal_runaway_protection(tr_state_machine_bed, temp_bed.current, temp_bed.target, -1, THERMAL_PROTECTION_BED_PERIOD, THERMAL_PROTECTION_BED_HYSTERESIS);
+      #endif
 
-    #if HEATER_IDLE_HANDLER
-      if (bed_idle.timed_out) {
-        temp_bed.soft_pwm_amount = 0;
-        #if DISABLED(PIDTEMPBED)
-          WRITE_HEATER_BED(LOW);
-        #endif
-      }
-      else
-    #endif
-    {
-      #if ENABLED(PIDTEMPBED)
-        temp_bed.soft_pwm_amount = WITHIN(temp_bed.current, BED_MINTEMP, BED_MAXTEMP) ? (int)get_pid_output_bed() >> 1 : 0;
-      #else
-        // Check if temperature is within the correct band
-        if (WITHIN(temp_bed.current, BED_MINTEMP, BED_MAXTEMP)) {
-          #if ENABLED(BED_LIMIT_SWITCHING)
-            if (temp_bed.current >= temp_bed.target + BED_HYSTERESIS)
-              temp_bed.soft_pwm_amount = 0;
-            else if (temp_bed.current <= temp_bed.target - (BED_HYSTERESIS))
-              temp_bed.soft_pwm_amount = MAX_BED_POWER >> 1;
-          #else // !PIDTEMPBED && !BED_LIMIT_SWITCHING
-            temp_bed.soft_pwm_amount = temp_bed.current < temp_bed.target ? MAX_BED_POWER >> 1 : 0;
-          #endif
-        }
-        else {
+      #if HEATER_IDLE_HANDLER
+        if (bed_idle.timed_out) {
           temp_bed.soft_pwm_amount = 0;
-          WRITE_HEATER_BED(LOW);
+          #if DISABLED(PIDTEMPBED)
+            WRITE_HEATER_BED(LOW);
+          #endif
         }
+        else
       #endif
-    }
+      {
+        #if ENABLED(PIDTEMPBED)
+          temp_bed.soft_pwm_amount = WITHIN(temp_bed.current, BED_MINTEMP, BED_MAXTEMP) ? (int)get_pid_output_bed() >> 1 : 0;
+        #else
+          // Check if temperature is within the correct band
+          if (WITHIN(temp_bed.current, BED_MINTEMP, BED_MAXTEMP)) {
+            #if ENABLED(BED_LIMIT_SWITCHING)
+              if (temp_bed.current >= temp_bed.target + BED_HYSTERESIS)
+                temp_bed.soft_pwm_amount = 0;
+              else if (temp_bed.current <= temp_bed.target - (BED_HYSTERESIS))
+                temp_bed.soft_pwm_amount = MAX_BED_POWER >> 1;
+            #else // !PIDTEMPBED && !BED_LIMIT_SWITCHING
+              temp_bed.soft_pwm_amount = temp_bed.current < temp_bed.target ? MAX_BED_POWER >> 1 : 0;
+            #endif
+          }
+          else {
+            temp_bed.soft_pwm_amount = 0;
+            WRITE_HEATER_BED(LOW);
+          }
+        #endif
+      }
+
+    } while (false);
+
   #endif // HAS_HEATED_BED
 
   #if HAS_HEATED_CHAMBER
@@ -1123,35 +1128,36 @@ void Temperature::manage_heater() {
 
     #if WATCH_CHAMBER
       // Make sure temperature is increasing
-      if (watch_chamber.elapsed(ms)) {                  // Time to check the chamber?
-        if (degChamber() < watch_chamber.target)   // Failed to increase enough?
+      if (watch_chamber.elapsed(ms)) {              // Time to check the chamber?
+        if (degChamber() < watch_chamber.target)    // Failed to increase enough?
           _temp_error(-2, PSTR(MSG_T_HEATING_FAILED), TEMP_ERR_PSTR(MSG_HEATING_FAILED_LCD, -2));
         else
-          start_watching_chamber();                     // Start again if the target is still far off
+          start_watching_chamber();                 // Start again if the target is still far off
       }
-    #endif // WATCH_CHAMBER
+    #endif
 
-    if (PENDING(ms, next_chamber_check_ms)) return;
-    next_chamber_check_ms = ms + CHAMBER_CHECK_INTERVAL;
+    if (ELAPSED(ms, next_chamber_check_ms)) {
+      next_chamber_check_ms = ms + CHAMBER_CHECK_INTERVAL;
 
-    if (WITHIN(temp_chamber.current, CHAMBER_MINTEMP, CHAMBER_MAXTEMP)) {
-      #if ENABLED(CHAMBER_LIMIT_SWITCHING)
-        if (temp_chamber.current >= temp_chamber.target + TEMP_CHAMBER_HYSTERESIS)
-          temp_chamber.soft_pwm_amount = 0;
-        else if (temp_chamber.current <= temp_chamber.target - (TEMP_CHAMBER_HYSTERESIS))
-          temp_chamber.soft_pwm_amount = MAX_CHAMBER_POWER >> 1;
-      #else
-        temp_chamber.soft_pwm_amount = temp_chamber.current < temp_chamber.target ? MAX_CHAMBER_POWER >> 1 : 0;
+      if (WITHIN(temp_chamber.current, CHAMBER_MINTEMP, CHAMBER_MAXTEMP)) {
+        #if ENABLED(CHAMBER_LIMIT_SWITCHING)
+          if (temp_chamber.current >= temp_chamber.target + TEMP_CHAMBER_HYSTERESIS)
+            temp_chamber.soft_pwm_amount = 0;
+          else if (temp_chamber.current <= temp_chamber.target - (TEMP_CHAMBER_HYSTERESIS))
+            temp_chamber.soft_pwm_amount = MAX_CHAMBER_POWER >> 1;
+        #else
+          temp_chamber.soft_pwm_amount = temp_chamber.current < temp_chamber.target ? MAX_CHAMBER_POWER >> 1 : 0;
+        #endif
+      }
+      else {
+        temp_chamber.soft_pwm_amount = 0;
+        WRITE_HEATER_CHAMBER(LOW);
+      }
+
+      #if ENABLED(THERMAL_PROTECTION_CHAMBER)
+        thermal_runaway_protection(tr_state_machine_chamber, temp_chamber.current, temp_chamber.target, -2, THERMAL_PROTECTION_CHAMBER_PERIOD, THERMAL_PROTECTION_CHAMBER_HYSTERESIS);
       #endif
     }
-    else {
-      temp_chamber.soft_pwm_amount = 0;
-      WRITE_HEATER_CHAMBER(LOW);
-    }
-
-    #if ENABLED(THERMAL_PROTECTION_CHAMBER)
-      thermal_runaway_protection(tr_state_machine_chamber, temp_chamber.current, temp_chamber.target, -2, THERMAL_PROTECTION_CHAMBER_PERIOD, THERMAL_PROTECTION_CHAMBER_HYSTERESIS);
-    #endif
 
     // TODO: Implement true PID pwm
     //temp_bed.soft_pwm_amount = WITHIN(temp_chamber.current, CHAMBER_MINTEMP, CHAMBER_MAXTEMP) ? (int)get_pid_output_chamber() >> 1 : 0;
@@ -1788,8 +1794,8 @@ void Temperature::init() {
 
 #if WATCH_CHAMBER
   /**
-   * Start Heating Sanity Check for hotends that are below
-   * their target temperature by a configurable margin.
+   * Start Heating Sanity Check for chamber that is below
+   * its target temperature by a configurable margin.
    * This is called when the temperature is set. (M141, M191)
    */
   void Temperature::start_watching_chamber() {

config/default/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Anet/A2/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Anet/A2plus/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Anet/A6/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Anet/A8/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/ArmEd/Configuration_adv.h

@@ -112,7 +112,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Cartesio/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/CR-10/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/CR-8/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Einstart-S/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Felix/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/JGAurora/A5/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/MakerParts/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Malyan/M150/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Malyan/M200/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Mks/Robin/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Mks/Sbase/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/RigidBot/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/SCARA/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Sanguinololu/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/TheBorg/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/TinyBoy2/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/VORONDesign/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Velleman/K8200/Configuration_adv.h

@@ -117,7 +117,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Velleman/K8400/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/generic/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/makibox/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/tvrrug/Round2/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false

config/examples/wt150/Configuration_adv.h

@@ -108,7 +108,6 @@
   #define CHAMBER_MINTEMP             5
   #define CHAMBER_MAXTEMP            60
   #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
-  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
   //#define CHAMBER_LIMIT_SWITCHING
   //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
   //#define HEATER_CHAMBER_INVERTING false