Patch up some language formatting

Marlin/language_cz.h

@@ -188,7 +188,7 @@
 #define MSG_INFO_EXTRUDERS                  "Extrudery"
 #define MSG_INFO_BAUDRATE                   "Rychlost"
 #define MSG_INFO_PROTOCOL                   "Protokol"
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_COUNT              "Pocet tisku"
   #define MSG_INFO_COMPLETED_PRINTS         "Dokonceno"
   #define MSG_INFO_PRINT_TIME               "Celkovy cas"

Marlin/language_da.h

@@ -190,7 +190,7 @@
 #define MSG_INFO_BAUDRATE                   "Baud"
 #define MSG_INFO_PROTOCOL                   "Protocol"
 
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_COUNT              "Ant. Prints"
   #define MSG_INFO_COMPLETED_PRINTS         "Færdige"
   #define MSG_INFO_PRINT_TIME               "Total print tid"

Marlin/language_de.h

@@ -185,7 +185,7 @@
 #define MSG_INFO_BAUDRATE                   "Baud"
 #define MSG_INFO_PROTOCOL                   "Protokol"
 
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_COUNT              "Gesamte Drucke"
   #define MSG_INFO_COMPLETED_PRINTS         "Beendete Drucke"
   #define MSG_INFO_PRINT_TIME               "Gesamte Druckzeit"

Marlin/language_el.h

@@ -180,7 +180,7 @@
 #define MSG_INFO_BAUDRATE                   "Baud"
 #define MSG_INFO_PROTOCOL                   "Protocol"
 
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_COUNT              "Print Count"
   #define MSG_INFO_COMPLETED_PRINTS         "Completed  "
   #define MSG_INFO_PRINT_TIME               "Total Time "

Marlin/language_en.h

@@ -488,7 +488,7 @@
   #define MSG_INFO_PROTOCOL                   "Protocol"
 #endif
 
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #ifndef MSG_INFO_PRINT_COUNT
     #define MSG_INFO_PRINT_COUNT              "Print Count"
   #endif

Marlin/language_fr.h

@@ -188,8 +188,7 @@
 #define MSG_INFO_BAUDRATE                   "Baud"
 #define MSG_INFO_PROTOCOL                   "Protocole"
 
-
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_COUNT              "Nbre impressions"
   #define MSG_INFO_COMPLETED_PRINTS         "Terminees"
   #define MSG_INFO_PRINT_TIME               "Tps impr. total"

Marlin/language_gl.h

@@ -182,18 +182,18 @@
 #define MSG_INFO_EXTRUDERS                  "Extrusores"
 #define MSG_INFO_BAUDRATE                   "Baudios"
 #define MSG_INFO_PROTOCOL                   "Protocolo"
-#if LCD_WIDTH > 19
-    #define MSG_INFO_PRINT_COUNT              "Total traballos"
-    #define MSG_INFO_COMPLETED_PRINTS         "Total completos"
-    #define MSG_INFO_PRINT_TIME               "Tempo impresion"
-    #define MSG_INFO_PRINT_LONGEST            "Traballo +longo"
-    #define MSG_INFO_PRINT_FILAMENT           "Total extruido"
+#if LCD_WIDTH >= 20
+  #define MSG_INFO_PRINT_COUNT              "Total traballos"
+  #define MSG_INFO_COMPLETED_PRINTS         "Total completos"
+  #define MSG_INFO_PRINT_TIME               "Tempo impresion"
+  #define MSG_INFO_PRINT_LONGEST            "Traballo +longo"
+  #define MSG_INFO_PRINT_FILAMENT           "Total extruido"
 #else
-    #define MSG_INFO_PRINT_COUNT              "Traballos"
-    #define MSG_INFO_COMPLETED_PRINTS         "Completos"
-    #define MSG_INFO_PRINT_TIME               "Tempo"
-    #define MSG_INFO_PRINT_LONGEST            "O +longo"
-    #define MSG_INFO_PRINT_FILAMENT           "Extruido"
+  #define MSG_INFO_PRINT_COUNT              "Traballos"
+  #define MSG_INFO_COMPLETED_PRINTS         "Completos"
+  #define MSG_INFO_PRINT_TIME               "Tempo"
+  #define MSG_INFO_PRINT_LONGEST            "O +longo"
+  #define MSG_INFO_PRINT_FILAMENT           "Extruido"
 #endif
 #define MSG_INFO_MIN_TEMP                   "Min Temp"
 #define MSG_INFO_MAX_TEMP                   "Max Temp"
@@ -203,31 +203,31 @@
 #define MSG_FILAMENT_CHANGE_OPTION_EXTRUDE  "Extruir mais"
 #define MSG_FILAMENT_CHANGE_OPTION_RESUME   "Segue traballo"
 #if LCD_HEIGHT >= 4
-    #define MSG_FILAMENT_CHANGE_INIT_1          "Agarde para"
-    #define MSG_FILAMENT_CHANGE_INIT_2          "iniciar troco"
-    #define MSG_FILAMENT_CHANGE_INIT_3          "de filamento"
-    #define MSG_FILAMENT_CHANGE_UNLOAD_1        "Agarde pola"
-    #define MSG_FILAMENT_CHANGE_UNLOAD_2        "descarga do"
-    #define MSG_FILAMENT_CHANGE_UNLOAD_3        "filamento"
-    #define MSG_FILAMENT_CHANGE_INSERT_1        "Introduza o"
-    #define MSG_FILAMENT_CHANGE_INSERT_2        "filamento e"
-    #define MSG_FILAMENT_CHANGE_INSERT_3        "faga click"
-    #define MSG_FILAMENT_CHANGE_LOAD_1          "Agarde pola"
-    #define MSG_FILAMENT_CHANGE_LOAD_2          "carga do"
-    #define MSG_FILAMENT_CHANGE_LOAD_3          "filamento"
-    #define MSG_FILAMENT_CHANGE_EXTRUDE_1       "Agarde pola"
-    #define MSG_FILAMENT_CHANGE_EXTRUDE_2       "extrusion do"
-    #define MSG_FILAMENT_CHANGE_EXTRUDE_3       "filamento"
-    #define MSG_FILAMENT_CHANGE_RESUME_1        "Agarde para"
-    #define MSG_FILAMENT_CHANGE_RESUME_2        "seguir co"
-    #define MSG_FILAMENT_CHANGE_RESUME_3        "traballo"
+  #define MSG_FILAMENT_CHANGE_INIT_1          "Agarde para"
+  #define MSG_FILAMENT_CHANGE_INIT_2          "iniciar troco"
+  #define MSG_FILAMENT_CHANGE_INIT_3          "de filamento"
+  #define MSG_FILAMENT_CHANGE_UNLOAD_1        "Agarde pola"
+  #define MSG_FILAMENT_CHANGE_UNLOAD_2        "descarga do"
+  #define MSG_FILAMENT_CHANGE_UNLOAD_3        "filamento"
+  #define MSG_FILAMENT_CHANGE_INSERT_1        "Introduza o"
+  #define MSG_FILAMENT_CHANGE_INSERT_2        "filamento e"
+  #define MSG_FILAMENT_CHANGE_INSERT_3        "faga click"
+  #define MSG_FILAMENT_CHANGE_LOAD_1          "Agarde pola"
+  #define MSG_FILAMENT_CHANGE_LOAD_2          "carga do"
+  #define MSG_FILAMENT_CHANGE_LOAD_3          "filamento"
+  #define MSG_FILAMENT_CHANGE_EXTRUDE_1       "Agarde pola"
+  #define MSG_FILAMENT_CHANGE_EXTRUDE_2       "extrusion do"
+  #define MSG_FILAMENT_CHANGE_EXTRUDE_3       "filamento"
+  #define MSG_FILAMENT_CHANGE_RESUME_1        "Agarde para"
+  #define MSG_FILAMENT_CHANGE_RESUME_2        "seguir co"
+  #define MSG_FILAMENT_CHANGE_RESUME_3        "traballo"
 #else // LCD_HEIGHT < 4
-    #define MSG_FILAMENT_CHANGE_INIT_1          "Agarde..."
-    #define MSG_FILAMENT_CHANGE_UNLOAD_1        "Descargando..."
-    #define MSG_FILAMENT_CHANGE_INSERT_1        "Introduza e click"
-    #define MSG_FILAMENT_CHANGE_LOAD_1          "Cargando..."
-    #define MSG_FILAMENT_CHANGE_EXTRUDE_1       "Extruindo..."
-    #define MSG_FILAMENT_CHANGE_RESUME_1        "Seguindo..."
+  #define MSG_FILAMENT_CHANGE_INIT_1          "Agarde..."
+  #define MSG_FILAMENT_CHANGE_UNLOAD_1        "Descargando..."
+  #define MSG_FILAMENT_CHANGE_INSERT_1        "Introduza e click"
+  #define MSG_FILAMENT_CHANGE_LOAD_1          "Cargando..."
+  #define MSG_FILAMENT_CHANGE_EXTRUDE_1       "Extruindo..."
+  #define MSG_FILAMENT_CHANGE_RESUME_1        "Seguindo..."
 #endif // LCD_HEIGHT < 4
 
 #endif // LANGUAGE_GL_H

Marlin/language_it.h

@@ -190,7 +190,7 @@
 #define MSG_INFO_EXTRUDERS                  "Estrusori"
 #define MSG_INFO_BAUDRATE                   "Baud"
 #define MSG_INFO_PROTOCOL                   "Protocollo"
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_COUNT              "Contat. stampa"
   #define MSG_INFO_COMPLETED_PRINTS         "Completati"
   #define MSG_INFO_PRINT_TIME               "Tempo totale"

Marlin/language_kana.h

@@ -89,7 +89,7 @@
 #define MSG_MIN                             LCD_STR_THERMOMETER " \xbb\xb2\xc3\xb2"                            // " ｻｲﾃｲ" (" Min")
 #define MSG_MAX                             LCD_STR_THERMOMETER " \xbb\xb2\xba\xb3"                            // " ｻｲｺｳ" (" Max")
 #define MSG_FACTOR                          LCD_STR_THERMOMETER " \xcc\xa7\xb8\xc0\xb0"                        // " ﾌｧｸﾀｰ" (" Fact")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_AUTOTEMP                      "\xbc\xde\xc4\xde\xb3\xb5\xdd\xc4\xde\xbe\xb2\xb7\xde\xae"         // "ｼﾞﾄﾞｳｵﾝﾄﾞｾｲｷﾞｮ" ("Autotemp")
 #else
   #define MSG_AUTOTEMP                      "\xbc\xde\xc4\xde\xb3\xb5\xdd\xc4\xde"                             // "ｼﾞﾄﾞｳｵﾝﾄﾞ" ("Autotemp")
@@ -101,7 +101,7 @@
 #define MSG_PID_D                           "PID-D"
 #define MSG_PID_C                           "PID-C"
 #define MSG_SELECT                          "\xbe\xdd\xc0\xb8"                                                 // "ｾﾝﾀｸ" ("Select")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_ACC                           "\xb6\xbf\xb8\xc4\xde mm/s2"                                       // "ｶｿｸﾄﾞ mm/s2" ("Accel")
   #define MSG_VX_JERK                       "X\xbc\xde\xb8\x20\xd4\xb8\xc4\xde mm/s"                           // "Xｼﾞｸ ﾔｸﾄﾞ mm/s" ("Vx-jerk")
   #define MSG_VY_JERK                       "Y\xbc\xde\xb8\x20\xd4\xb8\xc4\xde mm/s"                           // "Yｼﾞｸ ﾔｸﾄﾞ mm/s" ("Vy-jerk")
@@ -132,7 +132,7 @@
 #define MSG_MOTION                          "\xb3\xba\xde\xb7\xbe\xaf\xc3\xb2"                                 // "ｳｺﾞｷｾｯﾃｲ" ("Motion")
 #define MSG_VOLUMETRIC                      "\xcc\xa8\xd7\xd2\xdd\xc4"                                         // "ﾌｨﾗﾒﾝﾄ" ("Filament")
 #define MSG_VOLUMETRIC_ENABLED              "E in mm3"
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_FILAMENT_DIAM                 "\xcc\xa8\xd7\xd2\xdd\xc4\xc1\xae\xaf\xb9\xb2"                     // "ﾌｨﾗﾒﾝﾄﾁｮｯｹｲ" ("Fil. Dia.")
 #else
   #define MSG_FILAMENT_DIAM                 "\xcc\xa8\xd7\xd2\xdd\xc4\xb9\xb2"                                 // "ﾌｨﾗﾒﾝﾄｹｲ" ("Fil. Dia.")
@@ -157,7 +157,7 @@
 #define MSG_NO_MOVE                         "\xb3\xba\xde\xb7\xcf\xbe\xdd"                                     // "ｳｺﾞｷﾏｾﾝ" ("No move.")
 #define MSG_KILLED                          "\xcb\xbc\xde\xae\xb3\xc3\xb2\xbc"                                 // "ﾋｼﾞｮｳﾃｲｼ" ("KILLED. ")
 #define MSG_STOPPED                         "\xc3\xb2\xbc\xbc\xcf\xbc\xc0"                                     // "ﾃｲｼｼﾏｼﾀ" ("STOPPED. ")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_CONTROL_RETRACT               "\xcb\xb7\xba\xd0\xd8\xae\xb3 mm"                                  // "ﾋｷｺﾐﾘｮｳ mm" ("Retract mm")
   #define MSG_CONTROL_RETRACT_SWAP          "\xcb\xb7\xba\xd0\xd8\xae\xb3S mm"                                 // "ﾋｷｺﾐﾘｮｳS mm" ("Swap Re.mm")
   #define MSG_CONTROL_RETRACTF              "\xcb\xb7\xba\xd0\xbf\xb8\xc4\xde mm/s"                            // "ﾋｷｺﾐｿｸﾄﾞ mm/s" ("Retract  V")
@@ -179,14 +179,14 @@
 #define MSG_INIT_SDCARD                     "SD\xb6\xb0\xc4\xde\xbb\xb2\xd6\xd0\xba\xd0"                       // "SDｶｰﾄﾞｻｲﾖﾐｺﾐ" ("Init. SD card")
 #define MSG_CNG_SDCARD                      "SD\xb6\xb0\xc4\xde\xba\xb3\xb6\xdd"                               // "SDｶｰﾄﾞｺｳｶﾝ" ("Change SD card")
 #define MSG_ZPROBE_OUT                      "Z\xcc\xdf\xdb\xb0\xcc\xde\x20\xcd\xde\xaf\xc4\xde\xb6\xde\xb2"    // "Zﾌﾟﾛｰﾌﾞ ﾍﾞｯﾄﾞｶﾞｲ" ("Z probe out. bed")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_BLTOUCH_SELFTEST              "BLTouch \xbc\xde\xba\xbc\xdd\xc0\xde\xdd"                         // "BLTouch ｼﾞｺｼﾝﾀﾞﾝ" ("BLTouch Self-Test")
 #else
   #define MSG_BLTOUCH_SELFTEST              "BLTouch \xbe\xd9\xcc\xc3\xbd\xc4"                                 // "BLTouch ｾﾙﾌﾃｽﾄ" ("BLTouch Self-Test")
 #endif
 #define MSG_BLTOUCH_RESET                   "BLTouch \xd8\xbe\xaf\xc4"                                         // "BLTouch ﾘｾｯﾄ" ("Reset BLTouch")
 #define MSG_HOME                            "\xbb\xb7\xc6"                                                     // "ｻｷﾆ" ("Home") // Used as MSG_HOME " " MSG_X MSG_Y MSG_Z " " MSG_FIRST
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_FIRST                         "\xa6\xcc\xaf\xb7\xbb\xbe\xc3\xb8\xc0\xde\xbb\xb2"                 // "ｦﾌｯｷｻｾﾃｸﾀﾞｻｲ" ("first")
 #else
   #define MSG_FIRST                         "\xa6\xcc\xaf\xb7\xbb\xbe\xd6"                                     // "ｦﾌｯｷｻｾﾖ" ("first")
@@ -195,13 +195,13 @@
 #define MSG_BABYSTEP_X                      "X\xbc\xde\xb8\x20\xcb\xde\xc4\xde\xb3"                            // "Xｼﾞｸ ﾋﾞﾄﾞｳ" ("Babystep X")
 #define MSG_BABYSTEP_Y                      "Y\xbc\xde\xb8\x20\xcb\xde\xc4\xde\xb3"                            // "Yｼﾞｸ ﾋﾞﾄﾞｳ" ("Babystep Y")
 #define MSG_BABYSTEP_Z                      "Z\xbc\xde\xb8\x20\xcb\xde\xc4\xde\xb3"                            // "Zｼﾞｸ ﾋﾞﾄﾞｳ" ("Babystep Z")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_ENDSTOP_ABORT                 "\xb2\xc4\xde\xb3\xb9\xde\xdd\xb6\xb2\xb9\xdd\xc1\xb7\xc9\xb3"     // "ｲﾄﾞｳｹﾞﾝｶｲｹﾝﾁｷﾉｳ" ("Endstop abort")
 #else
   #define MSG_ENDSTOP_ABORT                 "\xb2\xc4\xde\xb3\xb9\xde\xdd\xb6\xb2\xb9\xdd\xc1"                 // "ｲﾄﾞｳｹﾞﾝｶｲｹﾝﾁ" ("Endstop abort")
 #endif
 #define MSG_HEATING_FAILED_LCD              "\xb6\xc8\xc2\xbc\xaf\xca\xdf\xb2"                                 // "ｶﾈﾂｼｯﾊﾟｲ" ("Heating failed")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_ERR_REDUNDANT_TEMP            "\xb4\xd7\xb0:\xbc\xde\xae\xb3\xc1\xae\xb3\xbb\xb0\xd0\xbd\xc0\xb0\xb7\xc9\xb3" // "ｴﾗｰ:ｼﾞｮｳﾁｮｳｻｰﾐｽﾀｰｷﾉｳ" ("Err: REDUNDANT TEMP")
 #else
   #define MSG_ERR_REDUNDANT_TEMP            "\xb4\xd7\xb0:\xbc\xde\xae\xb3\xc1\xae\xb3\xbb\xb0\xd0\xbd\xc0"                 // "ｴﾗｰ:ｼﾞｮｳﾁｮｳｻｰﾐｽﾀ" ("Err: REDUNDANT TEMP")
@@ -209,7 +209,7 @@
 #define MSG_THERMAL_RUNAWAY                 "\xc8\xc2\xce\xde\xb3\xbf\xb3"                                                  // "ﾈﾂﾎﾞｳｿｳ" ("THERMAL RUNAWAY")
 #define MSG_ERR_MAXTEMP                     "\xb4\xd7\xb0:\xbb\xb2\xba\xb3\xb5\xdd\xc1\xae\xb3\xb6"                         // "ｴﾗｰ:ｻｲｺｳｵﾝﾁｮｳｶ" ("Err: MAXTEMP")
 #define MSG_ERR_MINTEMP                     "\xb4\xd7\xb0:\xbb\xb2\xc3\xb2\xb5\xdd\xd0\xcf\xdd"                             // "ｴﾗｰ:ｻｲﾃｲｵﾝﾐﾏﾝ" ("Err: MINTEMP")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_ERR_MAXTEMP_BED               "\xb4\xd7\xb0:\xcd\xde\xaf\xc4\xde\x20\xbb\xb2\xba\xb3\xb5\xdd\xc1\xae\xb3\xb6" // "ｴﾗｰ:ﾍﾞｯﾄﾞ ｻｲｺｳｵﾝﾁｮｳｶ" ("Err: MAXTEMP BED")
   #define MSG_ERR_MINTEMP_BED               "\xb4\xd7\xb0:\xcd\xde\xaf\xc4\xde\x20\xbb\xb2\xc3\xb2\xb5\xdd\xd0\xcf\xdd"     // "ｴﾗｰ:ﾍﾞｯﾄﾞ ｻｲﾃｲｵﾝﾐﾏﾝ" ("Err: MINTEMP BED")
 #else
@@ -243,20 +243,20 @@
 #define MSG_INFO_COMPLETED_PRINTS           "\xb6\xdd\xd8\xae\xb3\xbd\xb3"                                     // "ｶﾝﾘｮｳｽｳ" ("Completed")
 #define MSG_INFO_PRINT_TIME                 "\xcc\xdf\xd8\xdd\xc4\xbc\xde\xb6\xdd\xd9\xb2\xb9\xb2"             // "ﾌﾟﾘﾝﾄｼﾞｶﾝﾙｲｹｲ" ("Total print time")
 #define MSG_INFO_PRINT_LONGEST              "\xbb\xb2\xc1\xae\xb3\xcc\xdf\xd8\xdd\xc4\xbc\xde\xb6\xdd"         // "ｻｲﾁｮｳﾌﾟﾘﾝﾄｼﾞｶﾝ" ("Longest job time")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_FILAMENT           "\xcc\xa8\xd7\xd2\xdd\xc4\xbc\xd6\xb3\xd8\xae\xb3\xd9\xb2\xb9\xb2" // "ﾌｨﾗﾒﾝﾄｼﾖｳﾘｮｳﾙｲｹｲ" ("Extruded total")
 #else
   #define MSG_INFO_PRINT_FILAMENT           "\xcc\xa8\xd7\xd2\xdd\xc4\xbf\xb3\xbc\xd6\xb3\xd8\xae\xb3"         // "ﾌｨﾗﾒﾝﾄｿｳｼﾖｳﾘｮｳ" ("Extruded")
 #endif
 #define MSG_INFO_MIN_TEMP                   "\xbe\xaf\xc3\xb2\xbb\xb2\xc3\xb2\xb5\xdd"                         // "ｾｯﾃｲｻｲﾃｲｵﾝ" ("Min Temp")
 #define MSG_INFO_MAX_TEMP                   "\xbe\xaf\xc3\xb2\xbb\xb2\xba\xb3\xb5\xdd"                         // "ｾｯﾃｲｻｲｺｳｵﾝ" ("Max Temp")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PSU                      "\xc3\xde\xdd\xb9\xde\xdd\xbc\xad\xcd\xde\xc2"                     // "ﾃﾞﾝｹﾞﾝｼｭﾍﾞﾂ" ("Power Supply")
 #else
   #define MSG_INFO_PSU                      "\xc3\xde\xdd\xb9\xde\xdd"                                         // "ﾃﾞﾝｹﾞﾝ" ("Power Supply")
 #endif
 #define MSG_DRIVE_STRENGTH                  "\xd3\xb0\xc0\xb0\xb8\xc4\xde\xb3\xd8\xae\xb8"                     // "ﾓｰﾀｰｸﾄﾞｳﾘｮｸ" ("Drive Strength")
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_DAC_PERCENT                   "DAC\xbc\xad\xc2\xd8\xae\xb8 %"                                    // "DACｼｭﾂﾘｮｸ %" ("Driver %")
 #else
   #define MSG_DAC_PERCENT                   "DAC\xbc\xad\xc2\xd8\xae\xb8"                                      // "DACｼｭﾂﾘｮｸ" ("Driver %")
@@ -288,7 +288,7 @@
 #else // LCD_HEIGHT < 4
   #define MSG_FILAMENT_CHANGE_INIT_1        "\xba\xb3\xb6\xdd\xa6\xb6\xb2\xbc\xbc\xcf\xbd"                     // "ｺｳｶﾝｦｶｲｼｼﾏｽ" ("Please wait...")
   #define MSG_FILAMENT_CHANGE_UNLOAD_1      "\xcc\xa8\xd7\xd2\xdd\xc4\xc7\xb7\xc0\xde\xbc\xc1\xad\xb3"         // "ﾌｨﾗﾒﾝﾄﾇｷﾀﾞｼﾁｭｳ" ("Ejecting...")
-  #if LCD_WIDTH > 19
+  #if LCD_WIDTH >= 20
     #define MSG_FILAMENT_CHANGE_INSERT_1    "\xbf\xb3\xc6\xad\xb3\xbc\x2c\xb8\xd8\xaf\xb8\xbc\xc3\xb8\xc0\xde\xbb\xb2" // "ｿｳﾆｭｳｼ,ｸﾘｯｸｼﾃｸﾀﾞｻｲ" ("Insert and Click")
   #else
     #define MSG_FILAMENT_CHANGE_INSERT_1    "\xbf\xb3\xc6\xad\xb3\xbc\x2c\xb8\xd8\xaf\xb8\xbe\xd6"                     // "ｿｳﾆｭｳｼ,ｸﾘｯｸｾﾖ" ("Insert and Click")

Marlin/language_tr.h

@@ -186,7 +186,7 @@
 #define MSG_INFO_BAUDRATE                   "\xddleti\xfeim H\xfdz\xfd"
 #define MSG_INFO_PROTOCOL                   "Protokol"
 
-#if LCD_WIDTH > 19
+#if LCD_WIDTH >= 20
   #define MSG_INFO_PRINT_COUNT              "Bask\xfd Say\xfds\xfd"
   #define MSG_INFO_COMPLETED_PRINTS         "Tamamlanan"
   #define MSG_INFO_PRINT_TIME               "Toplam Bask\xfd S\xfcresi"

Marlin/ultralcd_impl_HD44780.h

@@ -721,7 +721,7 @@ static void lcd_implementation_status_screen() {
     lcd.print(itostr3(feedrate_percentage));
     lcd.print('%');
 
-    #if LCD_WIDTH > 19 && ENABLED(SDSUPPORT)
+    #if LCD_WIDTH >= 20 && ENABLED(SDSUPPORT)
 
       lcd.setCursor(7, 2);
       lcd_printPGM(PSTR("SD"));
@@ -731,7 +731,7 @@ static void lcd_implementation_status_screen() {
         lcd_printPGM(PSTR("---"));
       lcd.print('%');
 
-    #endif // LCD_WIDTH > 19 && SDSUPPORT
+    #endif // LCD_WIDTH >= 20 && SDSUPPORT
 
     lcd.setCursor(LCD_WIDTH - 6, 2);
     lcd.print(LCD_STR_CLOCK[0]);