allow Marlin to actually compile with Makefile pulled from Sprinter and a few other modifications

Marlin/Makefile

@@ -1,76 +1,65 @@
+# Sprinter Arduino Project Makefile
+# 
+# Makefile Based on:
+# Arduino 0011 Makefile
+# Arduino adaptation by mellis, eighthave, oli.keller
+#
+# This has been tested with Arduino 0022.
+# 
+# This makefile allows you to build sketches from the command line
+# without the Arduino environment (or Java).
+#
+# Detailed instructions for using the makefile:
+#
+#  1. Modify the line containg "INSTALL_DIR" to point to the directory that
+#     contains the Arduino installation (for example, under Mac OS X, this
+#     might be /Applications/arduino-0012).
+#
+#  2. Modify the line containing "PORT" to refer to the filename
+#     representing the USB or serial connection to your Arduino board
+#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
+#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.usb*).
+#
+#  3. Set the line containing "MCU" to match your board's processor. 
+#     Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth
+#     or Diecimila have the atmega168.  If you're using a LilyPad Arduino,
+#     change F_CPU to 8000000.
+#
+#  4. Type "make" and press enter to compile/verify your program.
+#
+#  5. Type "make upload", reset your Arduino board, and press enter to
+#     upload your program to the Arduino board.
+#
+# $Id$
+
 TARGET = $(notdir $(CURDIR))
-# CHANGE BELOW:
-#~ INSTALL_DIR = /Applications/Arduino.app/Contents/Resources/Java
-INSTALL_DIR = /home/bkubicek/software/arduino-0023
-#~ PORT = /dev/cu.usbserial*
-PORT = /dev/ttyACM0
-
-# Get these values from:
-#     $(INSTALL_DIR)/hardware/boards.txt
-#     (arduino-0022/hardware/arduino/boards.txt)
-# The values below are for the "Arduino Duemilanove or Nano w/ ATmega328"
-# now for "Arduino Mega 2560"
-UPLOAD_SPEED = 115200
-UPLOAD_PROTOCOL = stk500v2
-BUILD_MCU = atmega2560
-BUILD_F_CPU = 16000000L
-TERM=bash
-
-# getting undefined reference to `__cxa_pure_virtual'
-#~ [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1254180518 Arduino Forum - Makefile]
-#~ http://www.arduino.cc/playground/OpenBSD/CLI
-#~ [http://arduino.cc/forum/index.php?topic=52041.0 A "simple" makefile for Arduino]
-#~ [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1275488191 Arduino Forum - Configuring avr-gcc options in arduino IDE]
-# found in /usr/lib/gcc/avr/4.3.5/cc1plus; fixed with -Wl,--gc-section
+INSTALL_DIR = ../../arduino-0022/
+UPLOAD_RATE = 115200
+AVRDUDE_PROGRAMMER = arduino
+# PORT = /dev/arduino_A900G2I3
+PORT = /dev/arduino
+MCU = atmega1280
+#For "old" Arduino Mega
+#MCU = atmega1280
+#For Sanguinololu
+#MCU = atmega644p 
+F_CPU = 16000000
+
 
 ############################################################################
 # Below here nothing should be changed...
 
-LINKORDER=\
-applet/Marlin.cpp.o \
-applet/EEPROM.o  \
-applet/main.o \
-applet/MarlinSerial.o \
-applet/motion_control.o\
-applet/pins_arduino.o\
-applet/planner.o\
-applet/Print.o\
-applet/Sd2Card.o\
-applet/SdBaseFile.o\
-applet/SdFatUtil.o\
-applet/SdFile.o\
-applet/SdVolume.o\
-applet/stepper.o\
-applet/temperature.o\
-applet/WInterrupts.o\
-applet/wiring_analog.o\
-applet/wiring_digital.o\
-applet/wiring.o\
-applet/wiring_pulse.o\
-applet/wiring_shift.o\
-applet/WMath.o
-
-PDES=Marlin.pde  ultralcd.pde  watchdog.pde cardreader.pde  
 ARDUINO = $(INSTALL_DIR)/hardware/arduino/cores/arduino
-#
-#~ AVR_TOOLS_PATH = $(INSTALL_DIR)/hardware/tools/avr/bin
-# in Ubuntu, avr-gcc is installed separate;
-# only avrdude comes with the IDE
-AVR_TOOLS_PATH = /usr/bin
-AVR_DUDE_PATH = $(INSTALL_DIR)/hardware/tools
-#
-SRC = $(ARDUINO)/pins_arduino.c $(ARDUINO)/wiring.c \
-    $(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \
-    $(ARDUINO)/wiring_pulse.c \
-    $(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c
-# added applet/$(TARGET).cpp as in IDE 0022
-CXXSRC = $(ARDUINO)/HardwareSerial.cpp $(ARDUINO)/WMath.cpp \
-    $(ARDUINO)/Print.cpp \
-    $(ARDUINO)/main.cpp
-#    applet/$(TARGET).cpp # no need, having a rule now for applet/$(TARGET).cpp.o
-# added main.cpp, as in 0022
+AVR_TOOLS_PATH = 
+SRC =  $(ARDUINO)/pins_arduino.c $(ARDUINO)/wiring.c \
+$(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \
+$(ARDUINO)/wiring_pulse.c \
+$(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c
+CXXSRC = $(ARDUINO)/WMath.cpp $(ARDUINO)/WString.cpp\
+$(ARDUINO)/Print.cpp Marlin.cpp MarlinSerial.cpp Sd2Card.cpp SdBaseFile.cpp SdFatUtil.cpp SdFile.cpp SdVolume.cpp motion_control.cpp planner.cpp stepper.cpp temperature.cpp cardreader.cpp
 FORMAT = ihex
 
+
 # Name of this Makefile (used for "make depend").
 MAKEFILE = Makefile
 
@@ -79,192 +68,128 @@ MAKEFILE = Makefile
 # AVR (extended) COFF requires stabs, plus an avr-objcopy run.
 DEBUG = stabs
 
-OPT = 2
+OPT = s
 
 # Place -D or -U options here
-#~ CDEFS = -DBUILD_F_CPU=$(BUILD_F_CPU)
-#~ CXXDEFS = -DBUILD_F_CPU=$(BUILD_F_CPU)
-# now called DF_CPU
-CDEFS = -DF_CPU=$(BUILD_F_CPU) -DARDUINO=23
-CXXDEFS = -DF_CPU=$(BUILD_F_CPU) -DARDUINO=23
+CDEFS = -DF_CPU=$(F_CPU)
+CXXDEFS = -DF_CPU=$(F_CPU)
 
 # Place -I options here
-CINCS = -I$(ARDUINO) -I$(INSTALL_DIR)/libraries/LiquidCrystal/ -I$(INSTALL_DIR)/libraries/EEPROM/
+CINCS = -I$(ARDUINO)
 CXXINCS = -I$(ARDUINO)
 
 # Compiler flag to set the C Standard level.
-# c89 - "ANSI" C
+# c89   - "ANSI" C
 # gnu89 - c89 plus GCC extensions
-# c99 - ISO C99 standard (not yet fully implemented)
+# c99   - ISO C99 standard (not yet fully implemented)
 # gnu99 - c99 plus GCC extensions
-CSTANDARD = -std=gnu99
+#CSTANDARD = -std=gnu99
 CDEBUG = -g$(DEBUG)
-# note that typically, IDE 0022 uses -w to suppress warnings (both in cpp and c)!
-CWARN = -Wall
-#~ CWARN = -w
-#  "-Wstrict-prototypes" is valid for Ada/C/ObjC but not for C++:
-CCWARN = -Wstrict-prototypes
-CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
+CWARN = -Wall -Wstrict-prototypes
+CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -w -ffunction-sections -fdata-sections -DARDUINO=22
 #CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
 
-# to eliminate pins_ardiuno warnings:
-# http://arduino.cc/pipermail/developers_arduino.cc/2010-December/004005.html
-
-# [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1254180518 Arduino Forum - Makefile]
-#~ For building the objects files "-ffunction-sections -fdata-sections" was missing
-#~ and the final avr-gcc call needs "-Wl,--gc-section".
-CXSECTF = -fno-exceptions -ffunction-sections -fdata-sections
-CFINALF = -Wl,--gc-section
-
-CFLAGS = $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CCWARN) $(CSTANDARD) $(CEXTRA)
-# added CWARN also to .cpp
-CXXFLAGS = $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CXSECTF)
-#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs
+CFLAGS = $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CEXTRA) $(CTUNING)
+CXXFLAGS = $(CDEFS) $(CINCS) -O$(OPT) -Wall $(CEXTRA) $(CTUNING)
+#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 
 LDFLAGS = -lm
 
+
 # Programming support using avrdude. Settings and variables.
 AVRDUDE_PORT = $(PORT)
-AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -V -F \
-    -p $(BUILD_MCU) -P $(AVRDUDE_PORT) -c $(UPLOAD_PROTOCOL) \
-    -b $(UPLOAD_SPEED) -C $(INSTALL_DIR)/hardware/tools/avrdude.conf
-#    -b $(UPLOAD_SPEED) -C $(INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf
+AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex:i
+AVRDUDE_FLAGS = -D -C $(INSTALL_DIR)/hardware/tools/avrdude.conf \
+-p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
+-b $(UPLOAD_RATE)
 
 # Program settings
-CC = $(AVR_TOOLS_PATH)/avr-gcc
-CXX = $(AVR_TOOLS_PATH)/avr-g++
-OBJCOPY = $(AVR_TOOLS_PATH)/avr-objcopy
-OBJDUMP = $(AVR_TOOLS_PATH)/avr-objdump
-AR = $(AVR_TOOLS_PATH)/avr-ar
-SIZE = $(AVR_TOOLS_PATH)/avr-size
-NM = $(AVR_TOOLS_PATH)/avr-nm
-#~ AVRDUDE = $(AVR_TOOLS_PATH)/avrdude
-AVRDUDE = $(AVR_DUDE_PATH)/avrdude
+CC = $(AVR_TOOLS_PATH)avr-gcc
+CXX = $(AVR_TOOLS_PATH)avr-g++
+OBJCOPY = $(AVR_TOOLS_PATH)avr-objcopy
+OBJDUMP = $(AVR_TOOLS_PATH)avr-objdump
+AR  = $(AVR_TOOLS_PATH)avr-ar
+SIZE = $(AVR_TOOLS_PATH)avr-size
+NM = $(AVR_TOOLS_PATH)avr-nm
+AVRDUDE = avrdude
 REMOVE = rm -f
 MV = mv -f
 
 # Define all object files.
-# NOTE: obj files will be created in respective src directories (libraries or $(INSTALL_DIR));
-#  make clean deletes them fine
-# note that srcs are in libraries or other directories;
-# $(CXXSRC:.cpp=.o) will cause obj files to be in same loc as src files
-#~ OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-# to change the output directory for object files;
-# must change the obj list here!
-# and then, match to corresponding rule somehow?
-# or leave this - and parse in rule (auth automatic variable $(@F))?
-# "Suffix Replacement"
-CXXSRC+=MarlinSerial.cpp    SdBaseFile.cpp  stepper.cpp motion_control.cpp SdFatUtil.cpp temperature.cpp planner.cpp SdFile.cpp Sd2Card.cpp SdVolume.cpp
-OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-
-# added - OBJ list, transformed into applet/
-OBJT = $(addprefix applet/,$(notdir $(OBJ)))
-ALLSRC = $(SRC) $(CXXSRC) $(ASRC)
+OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) 
 
 # Define all listing files.
 LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
 
 # Combine all necessary flags and optional flags.
 # Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(BUILD_MCU) -I. $(CFLAGS)
-ALL_CXXFLAGS = -mmcu=$(BUILD_MCU) -I. $(CXXFLAGS)
-ALL_ASFLAGS = -mmcu=$(BUILD_MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-# depended libraries of .pde need to be added from
-# $(INSTALL_DIR)/libraries (TODO: and/or ~/sketchbook/libraries)
-# grep for 'include', test if exists, add...
-# note: prefix "a real tab character" http://www.delorie.com/djgpp/doc/ug/larger/makefiles.html
-# $$ to escape $ for shell;
-# note: must NOT put comments # inside bash execution;
-# those would get removed by make; making shell see "EOF in backquote substitution"
-#		 echo $$ix ; \
-# 'shell' twice - for each subprocess! Backtick doesn't get expanded?
-GREPRES:=$(shell for ix in $(shell grep include $(TARGET).pde | sed 's/.*[<"]\(.*\).h[>"].*/\1/'); do \
-		if [ -d $(INSTALL_DIR)/libraries/$$ix ] ; then \
-			LINCS="$$LINCS -I$(INSTALL_DIR)/libraries/$$ix" ;\
-		fi; \
-	done; \
-	echo $$LINCS)
-# append includes:
-CINCS += $(GREPRES)
-CXXINCS += $(GREPRES)
-# append library source .cpp files too (CXXSRC)
-GREPRESB:=$(shell for ix in $(shell grep include $(TARGET).pde | sed 's/.*[<"]\(.*\).h[>"].*/\1/'); do \
-		if [ -d $(INSTALL_DIR)/libraries/$$ix ] ; then \
-			CPPSRCS="$$CPPSRCS $(INSTALL_DIR)/libraries/$$ix/*.cpp" ;\
-		fi; \
-	done; \
-	echo $$CPPSRCS)
-CXXSRC += $(GREPRESB)
-# added - only CXX obj from libraries:
-CXXLIBOBJ = $(GREPRESB:.cpp=.o)
+ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
+ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
+ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
+
 
 # Default target.
 all: applet_files build sizeafter
 
-build: elf hex
+build: elf hex 
 
 applet_files: $(TARGET).pde
-    # Here is the "preprocessing".
-    # It creates a .cpp file based with the same name as the .pde file.
-    # On top of the new .cpp file comes the WProgram.h header.
-    # At the end there is a generic main() function attached.
-    # Then the .cpp file will be compiled. Errors during compile will
-    # refer to this new, automatically generated, file.
-    # Not the original .pde file you actually edit...
+	# Here is the "preprocessing".
+	# It creates a .cpp file based with the same name as the .pde file.
+	# On top of the new .cpp file comes the WProgram.h header.
+	# At the end there is a generic main() function attached.
+	# Then the .cpp file will be compiled. Errors during compile will
+	# refer to this new, automatically generated, file. 
+	# Not the original .pde file you actually edit...
 	test -d applet || mkdir applet
-    # @ supresses printout of the cmdline itself; so only the out of echo is printed
-	@echo ALL OBJT: $(OBJT)
-	@echo ALL CXXLIBOBJ: $(CXXLIBOBJ)
-#	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
-	@echo "#include \"WProgram.h\"\nvoid setup();\nvoid loop();\n" > applet/$(TARGET).cpp
-	##cat $(TARGET).pde >> applet/$(TARGET).cpp
-	cat ${PDES}>> applet/$(TARGET).cpp
-	cp *.cpp applet/
-    # no more need to cat main.cpp (v0022) - now it is compiled in
-#	cat $(ARDUINO)/main.cpp >> applet/$(TARGET).cpp
-
+	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
+	cat $(TARGET).pde >> applet/$(TARGET).cpp
+	cat $(ARDUINO)/main.cpp >> applet/$(TARGET).cpp
 
 elf: applet/$(TARGET).elf
 hex: applet/$(TARGET).hex
 eep: applet/$(TARGET).eep
-lss: applet/$(TARGET).lss
+lss: applet/$(TARGET).lss 
 sym: applet/$(TARGET).sym
 
-# Program the device.
+# Program the device.  
 upload: applet/$(TARGET).hex
 	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
 
-# Display size of file.
+
+	# Display size of file.
 HEXSIZE = $(SIZE) --target=$(FORMAT) applet/$(TARGET).hex
-ELFSIZE = $(SIZE) applet/$(TARGET).elf
+ELFSIZE = $(SIZE)  applet/$(TARGET).elf
 sizebefore:
 	@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi
 
 sizeafter:
 	@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(HEXSIZE); echo; fi
 
+
 # Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
 COFFCONVERT=$(OBJCOPY) --debugging \
-    --change-section-address .data-0x800000 \
-    --change-section-address .bss-0x800000 \
-    --change-section-address .noinit-0x800000 \
-    --change-section-address .eeprom-0x810000
+--change-section-address .data-0x800000 \
+--change-section-address .bss-0x800000 \
+--change-section-address .noinit-0x800000 \
+--change-section-address .eeprom-0x810000 
+
 
 coff: applet/$(TARGET).elf
 	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf $(TARGET).cof
 
+
 extcoff: $(TARGET).elf
 	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf $(TARGET).cof
 
+
 .SUFFIXES: .elf .hex .eep .lss .sym
 
 .elf.hex:
 	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
 
 .elf.eep:
-    -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-    --change-section-lma .eeprom=0 -O $(FORMAT) $< $@
+	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
+	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
 
 # Create extended listing file from ELF output file.
 .elf.lss:
@@ -274,79 +199,50 @@ extcoff: $(TARGET).elf
 .elf.sym:
 	$(NM) -n $< > $@
 
-# Link: create ELF output file from library.
-# NOTE: applet/$(TARGET).cpp.o MUST BE BEFORE applet/core.a
-#  in the dependency list, so its rule runs first!
-applet/$(TARGET).elf: $(TARGET).pde applet/$(TARGET).cpp.o applet/core.a
-#	$(CC) $(ALL_CFLAGS) -o $@ applet/$(TARGET).cpp -L. applet/core.a $(LDFLAGS)
-# changed as in IDE v0022: link cpp obj files
-	@echo $$(tput bold)$$(tput setaf 2) $(CC) $$(tput sgr0) $(ALL_CFLAGS) $(CFINALF) -o $@ applet/$(TARGET).cpp.o $(CXXOBJ) -L. applet/core.a $(LDFLAGS)
-	echo ${OBJT}
-	#$(CC) $(ALL_CFLAGS) $(CFINALF) -o $@  applet/$(TARGET).cpp.o  -L. applet/core.a $(LDFLAGS)
-	$(CC) $(ALL_CFLAGS) $(CFINALF) -o $@ ${LINKORDER}   $(LDFLAGS)
-	#@$(CC) $(ALL_CFLAGS) $(CFINALF) -o $@ applet/*.o applet/$(TARGET).cpp.o $(CXXOBJ) -L. applet/core.a $(LDFLAGS)
-
-# added: cpp.o depends on cpp (and .pde which generates it)
-# $< "first item in the dependencies list"; $@ "left side of the :"; $^ "right side of the :"
-# http://www.cs.colby.edu/maxwell/courses/tutorials/maketutor/
-applet/$(TARGET).cpp.o: applet/$(TARGET).cpp
-	@echo $$(tput bold) $(CXX) $$(tput sgr0) -c $(ALL_CXXFLAGS) $< -o $@
-	@$(CXX) -c $(ALL_CXXFLAGS) $< -o $@
-
-#~ applet/core.a: $(OBJ)
-#~	 @for i in $(OBJ); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
-
-applet/core.a: $(OBJT)
-	 @for i in $(OBJT); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
-
-# iterate through OBJ to find the original location; then build depending on source extension
-# TODO: add handling of assembler files
-applet/%.o:
-	@for iob in $(OBJ); do \
-		if [ "`basename $$iob`" = "`basename $@`" ]; then \
-			for ios in $(ALLSRC); do \
-				if [ "$${iob%%.*}" = "$${ios%%.*}" ]; then \
-					case $${ios##*.} in \
-						"cpp") \
-							echo "$$(tput bold)$$(tput setaf 1) $(CXX) $$(tput sgr0) -c $(ALL_CXXFLAGS) $$ios -o $@"; \
-							$(CXX) -c $(ALL_CXXFLAGS) $$ios -o $@;; \
-						"c") \
-							echo "$$(tput bold)$$(tput setaf 1) $(CC) $$(tput sgr0) -c $(ALL_CFLAGS) $$ios -o $@"; \
-							$(CC) -c $(ALL_CFLAGS) $$ios -o $@;; \
-					esac; \
-				fi; \
-			done; \
-		fi; \
-	done;
-
-#~ # Compile: create object files from C++ source files.
-#~ .cpp.o:
-#~	 $(CXX) -c $(ALL_CXXFLAGS) $< -o $@
-
-#~ # Compile: create object files from C source files.
-#~ .c.o:
-#~	 $(CC) -c $(ALL_CFLAGS) $< -o $@
-
-#~ # Compile: create assembler files from C source files.
-#~ .c.s:
-#~	 $(CC) -S $(ALL_CFLAGS) $< -o $@
-
-#~ # Assemble: create object files from assembler source files.
-#~ .S.o:
-#~	 $(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-#~ # Automatic dependencies
-#~ %.d: %.c
-#~	 $(CC) -M $(ALL_CFLAGS) $< | sed "s;$(notdir $*).o:;$*.o $*.d:;" > $@
-
-#~ %.d: %.cpp
-#~	 $(CXX) -M $(ALL_CXXFLAGS) $< | sed "s;$(notdir $*).o:;$*.o $*.d:;" > $@
+	# Link: create ELF output file from library.
+applet/$(TARGET).elf: $(TARGET).pde applet/core.a 
+	$(CC) $(ALL_CFLAGS) -Wl,--gc-sections -o $@ applet/$(TARGET).cpp -L. applet/core.a $(LDFLAGS)
+
+applet/core.a: $(OBJ)
+	@for i in $(OBJ); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
+
+
+
+# Compile: create object files from C++ source files.
+.cpp.o:
+	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@ 
+
+# Compile: create object files from C source files.
+.c.o:
+	$(CC) -c $(ALL_CFLAGS) $< -o $@ 
+
+
+# Compile: create assembler files from C source files.
+.c.s:
+	$(CC) -S $(ALL_CFLAGS) $< -o $@
+
+
+# Assemble: create object files from assembler source files.
+.S.o:
+	$(CC) -c $(ALL_ASFLAGS) $< -o $@
+
+
 
 # Target: clean project.
 clean:
 	$(REMOVE) applet/$(TARGET).hex applet/$(TARGET).eep applet/$(TARGET).cof applet/$(TARGET).elf \
-        applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/core.a \
-        $(OBJT) applet/$(TARGET).cpp.o \
-        $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
-
-.PHONY: all build elf hex eep lss sym program coff extcoff clean applet_files sizebefore sizeafter
+	applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/core.a \
+	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
+
+depend:
+	if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
+	then \
+		sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
+			$(MAKEFILE).$$$$ && \
+		$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
+	fi
+	echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
+		>> $(MAKEFILE); \
+	$(CC) -M -mmcu=$(MCU) $(CDEFS) $(CINCS) $(SRC) $(ASRC) >> $(MAKEFILE)
+
+.PHONY:	all build elf hex eep lss sym program coff extcoff clean depend applet_files sizebefore sizeafter

Marlin/Marlin.h

@@ -14,7 +14,7 @@
 #include <string.h>
 #include <inttypes.h>
 
-#include <avr/delay.h>
+#include <util/delay.h>
 #include <avr/pgmspace.h>
 #include <avr/eeprom.h>
 #include  <avr/wdt.h>
@@ -55,7 +55,7 @@
 // //# define MYPGM(s) (__extension__({static prog_char __c[] = (s); &__c[0];})) 
 // //#define MYPGM(s) ((const prog_char *g PROGMEM=s))
 // //#define MYPGM(s) PSTR(s)
-#define MYPGM(s)  (__extension__({static char __c[] __attribute__((__progmem__)) = (s); &__c[0];}))  //This is the normal behaviour
+#define MYPGM(s)  (__extension__({static const char __c[] __attribute__((__progmem__)) = (s); &__c[0];}))  //This is the normal behaviour
 //#define MYPGM(s)  (__extension__({static prog_char __c[]  = (s); &__c[0];})) //this does not work but hides the warnings
 
 

Marlin/Marlin.pde

@@ -1301,8 +1301,10 @@ void manage_inactivity(byte debug)
       last_stepperdisabled_time=previous_millis_cmd;
     else
     {
-      if(  (X_ENABLE_ON && (READ(X_ENABLE_PIN)!=0))  ||  (!X_ENABLE_ON && READ(X_ENABLE_PIN)==0)  )
-        enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND); 
+      #if X_ENABLE_PIN >= 0
+        if(  (X_ENABLE_ON && (READ(X_ENABLE_PIN)!=0))  ||  (!X_ENABLE_ON && READ(X_ENABLE_PIN)==0)  )
+          enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND); 
+      #endif
       last_stepperdisabled_time=millis();
     }
   }

Marlin/temperature.cpp

@@ -85,9 +85,9 @@ static unsigned long  previous_millis_bed_heater;
   static unsigned char soft_pwm[EXTRUDERS];
   
 #ifdef WATCHPERIOD
-  static int watch_raw[EXTRUDERS] = { -1000 }; // the first value used for all
-  static int watch_oldtemp[3] = {0,0,0};
-  static unsigned long watchmillis = 0;
+  int watch_raw[EXTRUDERS] = { -1000 }; // the first value used for all
+  int watch_oldtemp[3] = {0,0,0};
+  unsigned long watchmillis = 0;
 #endif //WATCHPERIOD
 
 // Init min and max temp with extreme values to prevent false errors during startup
@@ -218,7 +218,7 @@ void manage_heater()
   
   #ifdef WATCHPERIOD
     if(watchmillis && millis() - watchmillis > WATCHPERIOD){
-        if(watch_oldtemp[TEMPSENSOR_HOTEND_0] >= degHotend(active_extruder)){
+        if(watch_oldtemp[0] >= degHotend(active_extruder)){
             setTargetHotend(0,active_extruder);
             LCD_MESSAGEPGM("Heating failed");
             SERIAL_ECHO_START;
@@ -527,7 +527,7 @@ void setWatch()
   for (int e = 0; e < EXTRUDERS; e++)
   {
     if(isHeatingHotend(e))
-    watch_oldtemp[TEMPSENSOR_HOTEND_0] = degHotend(0);
+    watch_oldtemp[0] = degHotend(0);
     {
       t = max(t,millis());
       watch_raw[e] = current_raw[e];