added MaKr3d Melzi board

Marlin/Configuration.h

@@ -17,8 +17,7 @@
 #define SERIAL_PORT 0
 
 // This determines the communication speed of the printer
-#define BAUDRATE 250000
-//#define BAUDRATE 115200
+#define BAUDRATE 115200
 
 //// The following define selects which electronics board you have. Please choose the one that matches your setup
 // 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
@@ -36,6 +35,7 @@
 // 63 = Melzi
 // 64 = STB V1.1
 // 65 = Azteeg X1
+// 66 = Melzi with ATmega1284 (MaKr3d version)
 // 7  = Ultimaker
 // 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
 // 77 = 3Drag Controller
@@ -371,10 +371,10 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
 // M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
 //define this to enable eeprom support
-//#define EEPROM_SETTINGS
+#define EEPROM_SETTINGS
 //to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
 // please keep turned on if you can.
-//#define EEPROM_CHITCHAT
+#define EEPROM_CHITCHAT
 
 // Preheat Constants
 #define PLA_PREHEAT_HOTEND_TEMP 180 
@@ -394,6 +394,10 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 //#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
 //#define ULTIPANEL  //the ultipanel as on thingiverse
 
+// The MaKr3d Makr-Panel with graphic controller and SD support
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//#define MAKRPANEL
+
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
@@ -419,6 +423,14 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 //#define RA_CONTROL_PANEL
 
 //automatic expansion
+#if defined (MAKRPANEL)
+ #define DOGLCD
+ #define SDSUPPORT
+ #define ULTIPANEL
+ #define NEWPANEL
+ #define DEFAULT_LCD_CONTRAST 17
+#endif
+
 #if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
  #define DOGLCD
  #define U8GLIB_ST7920

Marlin/Makefile

@@ -114,6 +114,12 @@ MCU              ?= atmega644p
 else ifeq  ($(HARDWARE_MOTHERBOARD),63)
 HARDWARE_VARIANT ?= Sanguino
 MCU              ?= atmega644p
+else ifeq  ($(HARDWARE_MOTHERBOARD),65)
+HARDWARE_VARIANT ?= Sanguino
+MCU              ?= atmega1284p
+else ifeq  ($(HARDWARE_MOTHERBOARD),66)
+HARDWARE_VARIANT ?= Sanguino
+MCU              ?= atmega1284p
 
 #Ultimaker
 else ifeq  ($(HARDWARE_MOTHERBOARD),7)

Marlin/dogm_lcd_implementation.h

@@ -78,7 +78,11 @@
 #ifdef U8GLIB_ST7920
 //U8GLIB_ST7920_128X64_RRD u8g(0,0,0);
 U8GLIB_ST7920_128X64_RRD u8g(0);
+#elsif defined(MAKRPANEL)
+// The MaKrPanel display, ST7565 controller as well
+U8GLIB_NHD_C12864 u8g(DOGLCD_CS, DOGLCD_A0);
 #else
+// for regular DOGM128 display with HW-SPI
 U8GLIB_DOGM128 u8g(DOGLCD_CS, DOGLCD_A0);	// HW-SPI Com: CS, A0
 #endif
 

Marlin/pins.h

@@ -843,13 +843,13 @@
 #if MOTHERBOARD == 64
 #define STB
 #endif
-#if MOTHERBOARD == 63
+#if MOTHERBOARD == 63 || MOTHERBOARD == 66
 #define MELZI
 #endif
 #if MOTHERBOARD == 65
 #define AZTEEG_X1
 #endif
-#if MOTHERBOARD == 62 || MOTHERBOARD == 63 || MOTHERBOARD == 64 || MOTHERBOARD == 65
+#if MOTHERBOARD == 62 || MOTHERBOARD == 63 || MOTHERBOARD == 64 || MOTHERBOARD == 65 || MOTHERBOARD == 66
 #undef MOTHERBOARD
 #define MOTHERBOARD 6
 #define SANGUINOLOLU_V_1_2
@@ -891,6 +891,8 @@
 
 #ifdef STB
 #define FAN_PIN            4
+	//  Uncomment this if you have the first generation (V1.10) of STBs board
+#define LCD_PIN_BL         17 // LCD backlight LED
 #endif
 
 #ifdef AZTEEG_X1
@@ -975,6 +977,27 @@
    #endif //Newpanel
  #endif //Ultipanel
 
+ #ifdef MAKRPANEL
+     #define BEEPER 29
+     // Pins for DOGM SPI LCD Support
+     #define DOGLCD_A0  30
+     #define DOGLCD_CS  17
+     #define LCD_PIN_BL	28	// backlight LED on PA3
+     // GLCD features
+     #define LCD_CONTRAST 1
+     // Uncomment screen orientation
+     #define LCD_SCREEN_ROT_0
+       // #define LCD_SCREEN_ROT_90
+       // #define LCD_SCREEN_ROT_180
+       // #define LCD_SCREEN_ROT_270
+     //The encoder and click button
+     #define BTN_EN1 11
+     #define BTN_EN2 10
+     #define BTN_ENC 16  //the click switch
+     //not connected to a pin
+     #define SDCARDDETECT -1    
+ #endif //Makrpanel
+
 #endif