Add NANODLP_ALL_AXIS to config examples

Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Anet/A6/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Anet/A8/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Creality/CR-10/Configuration_adv.h

@@ -1562,5 +1562,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Malyan/M150/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h

@@ -1560,5 +1560,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Sanguinololu/Configuration_adv.h

@@ -1526,5 +1526,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/TinyBoy2/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Velleman/K8200/Configuration_adv.h

@@ -1570,5 +1570,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Velleman/K8400/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/Wanhao/Duplicator 6/Configuration_adv.h

@@ -1561,5 +1561,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -1561,5 +1561,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -1561,5 +1561,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -1561,5 +1561,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -1561,5 +1561,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -1566,5 +1566,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -1561,5 +1561,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h

@@ -1560,5 +1560,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -1559,5 +1559,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H

Marlin/example_configurations/wt150/Configuration_adv.h

@@ -1549,5 +1549,9 @@
  * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  */
 //#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+  //#define NANODLP_ALL_AXIS  // Enables "Z_move_comp" output on any axis move.
+                              // Default behaviour is limited to Z axis only.
+#endif
 
 #endif // CONFIGURATION_ADV_H