New mods, now using TMC2100 and E3Dv6.

Marlin/Configuration.h

@@ -77,7 +77,7 @@
 #define STRING_CONFIG_H_AUTHOR "(xythobuz, CTC DIY)" // Who made the changes.
 #define SHOW_BOOTSCREEN
 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
-#define STRING_SPLASH_LINE2 WEBSITE_URL         // will be shown during bootup in line 2
+#define STRING_SPLASH_LINE2 "xythobuz.de"         // will be shown during bootup in line 2
 
 //
 // *** VENDORS PLEASE READ *****************************************************
@@ -352,9 +352,9 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  #define  DEFAULT_Kp 22.2
+  #define  DEFAULT_Ki 1.08
+  #define  DEFAULT_Kd 114
 
   // MakerGear
   //#define  DEFAULT_Kp 7.0
@@ -367,9 +367,9 @@
   //#define  DEFAULT_Kd 440
 
   // Anet A8 - using for CTC i3 Pro B
-  #define DEFAULT_Kp 21.0
-  #define DEFAULT_Ki 1.25
-  #define DEFAULT_Kd 86.0
+  //#define DEFAULT_Kp 21.0
+  //#define DEFAULT_Ki 1.25
+  //#define DEFAULT_Kd 86.0
 
 #endif // PIDTEMP
 
@@ -530,7 +530,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80.10, 80.10, 2560, 105.0 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80.10, 80.10, 400, 99.0 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -747,9 +747,9 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#define INVERT_X_DIR true
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR true
 
 // Enable this option for Toshiba stepper drivers
 //#define CONFIG_STEPPERS_TOSHIBA
@@ -758,10 +758,10 @@
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
 #define INVERT_E0_DIR true
-#define INVERT_E1_DIR false
-#define INVERT_E2_DIR false
-#define INVERT_E3_DIR false
-#define INVERT_E4_DIR false
+#define INVERT_E1_DIR true
+#define INVERT_E2_DIR true
+#define INVERT_E3_DIR true
+#define INVERT_E4_DIR true
 
 // @section homing
 

Marlin/Configuration_adv.h

@@ -599,16 +599,16 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
   //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
-  //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
   //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif