Move manual move to lcd section

Marlin/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/default/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)
@@ -1025,7 +1021,7 @@
    *    INT              --> SD_DETECT_PIN [1]
    *    SS               --> SDSS
    *
-   * [1] On AVR an interrupt-capable pin is required for UHS3 compatibility.
+   * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility.
    */
   //#define USB_FLASH_DRIVE_SUPPORT
   #if ENABLED(USB_FLASH_DRIVE_SUPPORT)

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -621,7 +621,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -648,19 +648,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -838,6 +825,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Alfawise/U20/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Anet/A2/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Anet/A2plus/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Anet/A6/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Anet/A8/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Anet/A8plus/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Anet/E16/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/ArmEd/Configuration_adv.h

@@ -624,7 +624,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -651,19 +651,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -841,6 +828,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 #define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -845,6 +832,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Cartesio/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/CR-10/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/CR-20 Pro/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/CR-20/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/CR-8/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 0 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 0 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Creality/Ender-5/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Einstart-S/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FYSETC/AIO_II/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,18 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -836,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FYSETC/Cheetah/base/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,18 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -836,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FYSETC/F6_13/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Felix/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -836,6 +823,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -624,7 +624,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -651,19 +651,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -841,6 +828,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -624,7 +624,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -651,19 +651,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -841,6 +828,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Geeetech/A10/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/HMS434/Configuration_adv.h

@@ -612,7 +612,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -639,19 +639,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section extras
-
 // minimum time in microseconds that a movement needs to take if the buffer is emptied.
 #define DEFAULT_MINSEGMENTTIME        20000
 
@@ -829,6 +816,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/JGAurora/A1/Configuration_adv.h

@@ -625,7 +625,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -652,19 +652,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 60*60, 60*60, 10*60, 10*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -842,6 +829,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 60*60, 60*60, 10*60, 10*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/JGAurora/A5/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 80*60, 80*60, 12*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 80*60, 80*60, 12*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -625,7 +625,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -652,19 +652,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 60*60, 60*60, 10*60, 10*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -842,6 +829,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 60*60, 60*60, 10*60, 10*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/MakerParts/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Malyan/M150/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Malyan/M200/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Mks/Robin/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Mks/Sbase/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -838,6 +825,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/RigidBot/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/SCARA/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 10*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 10*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Sanguinololu/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Tevo/Michelangelo/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,18 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -836,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Tevo/Tarantula Pro/Configuration_adv.h

@@ -616,7 +616,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -643,19 +643,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -833,6 +820,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,18 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -836,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,18 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -836,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/TheBorg/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/TinyBoy2/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/VORONDesign/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Velleman/K8200/Configuration_adv.h

@@ -633,7 +633,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -660,19 +660,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -850,6 +837,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Velleman/K8400/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 #define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 70*60, 70*60, 15*60, 6*60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +826,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 70*60, 70*60, 15*60, 6*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,19 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -837,6 +824,15 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/Dreammaker/Overlord/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/generic/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -620,7 +620,7 @@
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
-// @section machine
+// @section motion
 
 #define AXIS_RELATIVE_MODES { false, false, false, false }
 
@@ -647,20 +647,6 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// @section lcd
-
-#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE_XYZ 50*60
-  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
-  #if ENABLED(ULTIPANEL)
-    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
-    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
-  #endif
-#endif
-
-// @section motion
-
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
@@ -839,6 +825,16 @@
 
 // @section lcd
 
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
+  #define MANUAL_FEEDRATE_XYZ 50*60
+  #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
+#endif
+
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)