Adjust some config comments

Marlin/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

Marlin/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/default/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/default/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -625,13 +625,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1065,7 +1065,7 @@
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -640,13 +640,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1079,7 +1079,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/AliExpress/CL-260/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -631,13 +631,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1070,7 +1070,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2087,14 +2087,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A2/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A2/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A2plus/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A2plus/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A6/Configuration.h

@@ -640,13 +640,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1173,7 +1173,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A6/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A8/Configuration.h

@@ -633,13 +633,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1072,7 +1072,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A8/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A8plus/Configuration.h

@@ -631,13 +631,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1070,7 +1070,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A8plus/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/E16/Configuration.h

@@ -632,13 +632,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1071,7 +1071,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/E16/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/AnyCubic/i3/Configuration.h

@@ -630,13 +630,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1069,7 +1069,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/ArmEd/Configuration.h

@@ -621,13 +621,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1060,7 +1060,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/ArmEd/Configuration_adv.h

@@ -635,7 +635,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -751,7 +751,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2089,14 +2089,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Azteeg/X5GT/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BIBO/TouchX/default/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BQ/Hephestos/Configuration.h

@@ -608,13 +608,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1047,7 +1047,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BQ/Hephestos_2/Configuration.h

@@ -621,13 +621,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1060,7 +1060,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
 
   // Set one or more commands to execute on filament runout.

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 300
 #define DISABLE_INACTIVE_X false
 #define DISABLE_INACTIVE_Y false
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2093,14 +2093,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BQ/WITBOX/Configuration.h

@@ -608,13 +608,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1047,7 +1047,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Cartesio/Configuration.h

@@ -619,13 +619,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1058,7 +1058,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Cartesio/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10/Configuration.h

@@ -630,13 +630,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1069,7 +1069,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/CR-10/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10S/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING true // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
   #define FIL_RUNOUT_PIN 2 // Creality CR10-S stock sensor

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10_5S/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1061,7 +1061,7 @@
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
   #define FIL_RUNOUT_PIN 2 // Creality CR10-S stock sensor

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10mini/Configuration.h

@@ -639,13 +639,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1078,7 +1078,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-8/Configuration.h

@@ -630,13 +630,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1069,7 +1069,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/CR-8/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/Ender-2/Configuration.h

@@ -624,13 +624,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1063,7 +1063,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/Ender-3/Configuration.h

@@ -624,13 +624,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1063,7 +1063,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/Ender-4/Configuration.h

@@ -630,13 +630,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1069,7 +1069,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Dagoma/Disco Ultimate/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h

@@ -625,13 +625,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1064,7 +1064,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Einstart-S/Configuration.h

@@ -626,13 +626,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-//#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-//#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-//#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-//#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+//#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+//#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+//#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+//#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 #define X_STOP_INVERTING true
 #define Y_STOP_INVERTING true
@@ -1067,7 +1067,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Einstart-S/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Felix/Configuration.h

@@ -601,13 +601,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1041,7 +1041,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Felix/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Felix/DUAL/Configuration.h

@@ -601,13 +601,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1041,7 +1041,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -610,13 +610,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1052,7 +1052,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2084,14 +2084,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/FolgerTech/i3-2020/Configuration.h

@@ -625,13 +625,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1065,7 +1065,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Formbot/Raptor/Configuration.h

@@ -672,13 +672,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1157,7 +1157,7 @@
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN 57
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2087,14 +2087,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -649,13 +649,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1088,7 +1088,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -635,7 +635,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 600
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -751,7 +751,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2089,14 +2089,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Formbot/T_Rex_3/Configuration.h

@@ -629,13 +629,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1084,7 +1084,7 @@
   #ifndef NUM_RUNOUT_SENSORS
     #define NUM_RUNOUT_SENSORS   1
   #endif
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -635,7 +635,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 600
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -751,7 +751,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2089,14 +2089,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/A10/Configuration.h

@@ -603,13 +603,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1044,7 +1044,7 @@
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN      66
   //#define FIL_RUNOUT2_PIN     67
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensors.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/A10/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/A10M/Configuration.h

@@ -603,13 +603,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1044,7 +1044,7 @@
   #define NUM_RUNOUT_SENSORS   2     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN      66
   #define FIL_RUNOUT2_PIN     67
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensors.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/A20M/Configuration.h

@@ -603,13 +603,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1044,7 +1044,7 @@
   #define NUM_RUNOUT_SENSORS   2     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN      66
   #define FIL_RUNOUT2_PIN     67
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensors.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/GT2560/Configuration.h

@@ -635,13 +635,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1074,7 +1074,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -627,13 +627,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1066,7 +1066,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2084,14 +2084,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -634,13 +634,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1079,7 +1079,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -635,13 +635,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1079,7 +1079,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -620,13 +620,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1059,7 +1059,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Infitary/i3-M508/Configuration.h

@@ -624,13 +624,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1063,7 +1063,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/JGAurora/A1/Configuration.h

@@ -622,13 +622,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1061,7 +1061,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/JGAurora/A1/Configuration_adv.h

@@ -636,7 +636,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -752,7 +752,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2090,14 +2090,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/JGAurora/A5/Configuration.h

@@ -632,13 +632,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1071,7 +1071,7 @@
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/JGAurora/A5/Configuration_adv.h

@@ -631,7 +631,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -747,7 +747,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2085,14 +2085,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/JGAurora/A5S/Configuration.h

@@ -622,13 +622,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1061,7 +1061,7 @@
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -636,7 +636,7 @@
 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
@@ -752,7 +752,7 @@
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -2090,14 +2090,14 @@
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power