Adapt MESH_EDIT_GFX_OVERLAY for 1.1.x

.travis.yml

@@ -325,7 +325,7 @@ script:
   #
   - use_example_configs delta/generic
   - opt_disable DISABLE_MIN_ENDSTOPS
-  - opt_enable AUTO_BED_LEVELING_UBL Z_PROBE_ALLEN_KEY EEPROM_SETTINGS EEPROM_CHITCHAT OLED_PANEL_TINYBOY2
+  - opt_enable AUTO_BED_LEVELING_UBL Z_PROBE_ALLEN_KEY EEPROM_SETTINGS EEPROM_CHITCHAT OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY
   - build_marlin
   #
   # Delta Config (FLSUN AC because it's complex)

Marlin/Configuration.h

@@ -957,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/SanityCheck.h

@@ -216,6 +216,10 @@
   #error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration."
 #elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X)  || defined(UBL_MESH_MAX_Y)
   #error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration."
+#elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY)
+  #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration."
+#elif defined(BABYSTEP_ZPROBE_GFX_REVERSE)
+  #error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations."
 #endif
 
 /**
@@ -810,6 +814,10 @@ static_assert(1 >= 0
   #error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL."
 #endif
 
+#if ENABLED(MESH_EDIT_GFX_OVERLAY) && (DISABLED(AUTO_BED_LEVELING_UBL) || DISABLED(DOGLCD))
+  #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD."
+#endif
+
 /**
  * LCD_BED_LEVELING requirements
  */

Marlin/dogm_bitmaps.h

@@ -420,7 +420,7 @@
     };
   #endif // Extruders
 
-  #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY)
+  #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(MESH_EDIT_GFX_OVERLAY)
     const unsigned char cw_bmp[] PROGMEM = { //AVR-GCC, WinAVR
       0x07,0xf8,0x00, // 000001111111100000000000
       0x0c,0x0c,0x00, // 000011000000110000000000
@@ -510,5 +510,5 @@
       0x1E,0x00, // 0001111000000000
       0x0C,0x00  // 0000110000000000
     };
-  #endif // BABYSTEP_ZPROBE_GFX_OVERLAY
+  #endif // BABYSTEP_ZPROBE_GFX_OVERLAY || MESH_EDIT_GFX_OVERLAY
 #endif // HAS_TEMP_BED

Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h

@@ -977,6 +977,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/AliExpress/CL-260/Configuration.h

@@ -957,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Anet/A6/Configuration.h

@@ -1100,6 +1100,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Anet/A6/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Anet/A8/Configuration.h

@@ -964,6 +964,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Anet/A8/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/BQ/Hephestos/Configuration.h

@@ -948,6 +948,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/BQ/Hephestos_2/Configuration.h

@@ -958,6 +958,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h

@@ -607,6 +607,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -641,7 +645,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/BQ/WITBOX/Configuration.h

@@ -948,6 +948,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Cartesio/Configuration.h

@@ -956,6 +956,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Creality/CR-10/Configuration.h

@@ -967,6 +967,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Creality/CR-10/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Felix/Configuration.h

@@ -939,6 +939,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -939,6 +939,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h

@@ -962,6 +962,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y 10

Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Geeetech/GT2560/Configuration.h

@@ -972,6 +972,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -957,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Infitary/i3-M508/Configuration.h

@@ -961,6 +961,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Malyan/M150/Configuration.h

@@ -985,6 +985,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Malyan/M150/Configuration_adv.h

@@ -607,6 +607,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -641,7 +645,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Micromake/C1/basic/Configuration.h

@@ -961,6 +961,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h

@@ -961,6 +961,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h

@@ -611,6 +611,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -957,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/RigidBot/Configuration.h

@@ -955,6 +955,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/SCARA/Configuration.h

@@ -969,6 +969,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Sanguinololu/Configuration.h

@@ -988,6 +988,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Sanguinololu/Configuration_adv.h

@@ -599,6 +599,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -633,7 +637,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/TinyBoy2/Configuration.h

@@ -1013,6 +1013,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/TinyBoy2/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Velleman/K8200/Configuration.h

@@ -987,6 +987,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Velleman/K8200/Configuration_adv.h

@@ -618,6 +618,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -652,7 +656,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Velleman/K8400/Configuration.h

@@ -957,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/Velleman/K8400/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h

@@ -957,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -957,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h

@@ -1089,6 +1089,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h

@@ -1083,6 +1083,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/delta/generic/Configuration.h

@@ -1078,6 +1078,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -1081,6 +1081,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -1081,6 +1081,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -617,6 +617,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -651,7 +655,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -1090,6 +1090,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h

@@ -971,6 +971,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 45             // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/makibox/Configuration.h

@@ -960,6 +960,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -952,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/example_configurations/wt150/Configuration.h

@@ -962,6 +962,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/example_configurations/wt150/Configuration_adv.h

@@ -600,6 +600,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -634,7 +638,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/ultralcd.cpp

@@ -1035,6 +1035,44 @@ void kill_screen(const char* lcd_msg) {
     }
   #endif
 
+  #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(MESH_EDIT_GFX_OVERLAY)
+
+    void _lcd_zoffset_overlay_gfx(const float zvalue) {
+      // Determine whether the user is raising or lowering the nozzle.
+      static int8_t dir;
+      static float old_zvalue;
+      if (zvalue != old_zvalue) {
+        dir = zvalue ? zvalue < old_zvalue ? -1 : 1 : 0;
+        old_zvalue = zvalue;
+      }
+
+      #if ENABLED(OVERLAY_GFX_REVERSE)
+        const unsigned char *rot_up = ccw_bmp, *rot_down = cw_bmp;
+      #else
+        const unsigned char *rot_up = cw_bmp, *rot_down = ccw_bmp;
+      #endif
+
+      #if ENABLED(USE_BIG_EDIT_FONT)
+        const int left = 0, right = 45, nozzle = 95;
+      #else
+        const int left = 5, right = 90, nozzle = 60;
+      #endif
+
+      // Draw a representation of the nozzle
+      if (PAGE_CONTAINS(3, 16))  u8g.drawBitmapP(nozzle + 6, 4 - dir, 2, 12, nozzle_bmp);
+      if (PAGE_CONTAINS(20, 20)) u8g.drawBitmapP(nozzle + 0, 20, 3, 1, offset_bedline_bmp);
+
+      // Draw cw/ccw indicator and up/down arrows.
+      if (PAGE_CONTAINS(47, 62)) {
+        u8g.drawBitmapP(left  + 0, 47, 3, 16, rot_down);
+        u8g.drawBitmapP(right + 0, 47, 3, 16, rot_up);
+        u8g.drawBitmapP(right + 20, 48 - dir, 2, 13, up_arrow_bmp);
+        u8g.drawBitmapP(left  + 20, 49 - dir, 2, 13, down_arrow_bmp);
+      }
+    }
+
+  #endif // BABYSTEP_ZPROBE_GFX_OVERLAY || MESH_EDIT_GFX_OVERLAY
+
   #if ENABLED(BABYSTEPPING)
 
     void _lcd_babystep(const AxisEnum axis, const char* msg) {
@@ -1060,48 +1098,6 @@ void kill_screen(const char* lcd_msg) {
 
     #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
 
-      #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY)
-        void _lcd_babystep_zoffset_overlay(const float zprobe_zoffset) {
-          // Determine whether the user is raising or lowering the nozzle.
-          static int dir = 0;
-          static float old_zprobe_zoffset = 0;
-          if (zprobe_zoffset != old_zprobe_zoffset) {
-            dir = (zprobe_zoffset > old_zprobe_zoffset) ? 1 : -1;
-            old_zprobe_zoffset = zprobe_zoffset;
-          }
-
-          #if ENABLED(BABYSTEP_ZPROBE_GFX_REVERSE)
-            const unsigned char* rot_up   = ccw_bmp;
-            const unsigned char* rot_down = cw_bmp;
-          #else
-            const unsigned char* rot_up   = cw_bmp;
-            const unsigned char* rot_down = ccw_bmp;
-          #endif
-
-          #if ENABLED(USE_BIG_EDIT_FONT)
-            const int left   = 0,
-                      right  = 45,
-                      nozzle = 95;
-          #else
-            const int left   = 5,
-                      right  = 90,
-                      nozzle = 60;
-          #endif
-
-          // Draw a representation of the nozzle
-          if (PAGE_CONTAINS(3, 16))  u8g.drawBitmapP(nozzle + 6, 4 - dir, 2, 12, nozzle_bmp);
-          if (PAGE_CONTAINS(20, 20)) u8g.drawBitmapP(nozzle + 0, 20, 3, 1, offset_bedline_bmp);
-
-          // Draw cw/ccw indicator and up/down arrows.
-          if (PAGE_CONTAINS(47, 62)) {
-            u8g.drawBitmapP(left  + 0, 47, 3, 16, rot_down);
-            u8g.drawBitmapP(right + 0, 47, 3, 16, rot_up);
-            u8g.drawBitmapP(right + 20, 48 - dir, 2, 13, up_arrow_bmp);
-            u8g.drawBitmapP(left  + 20, 49 - dir, 2, 13, down_arrow_bmp);
-          }
-        }
-      #endif // BABYSTEP_ZPROBE_GFX_OVERLAY
-
       void lcd_babystep_zoffset() {
         if (lcd_clicked) { return lcd_goto_previous_menu_no_defer(); }
         defer_return_to_status = true;
@@ -1123,7 +1119,7 @@ void kill_screen(const char* lcd_msg) {
         if (lcdDrawUpdate) {
           lcd_implementation_drawedit(PSTR(MSG_ZPROBE_ZOFFSET), ftostr43sign(zprobe_zoffset));
           #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY)
-            _lcd_babystep_zoffset_overlay(zprobe_zoffset);
+            _lcd_zoffset_overlay_gfx(zprobe_zoffset);
           #endif
         }
       }
@@ -1158,8 +1154,12 @@ void kill_screen(const char* lcd_msg) {
         mesh_edit_value = float(rounded - (rounded % 5L)) / 1000.0;
       }
 
-      if (lcdDrawUpdate)
+      if (lcdDrawUpdate) {
         lcd_implementation_drawedit(msg, ftostr43sign(mesh_edit_value));
+        #if ENABLED(MESH_EDIT_GFX_OVERLAY)
+          _lcd_zoffset_overlay_gfx(mesh_edit_value);
+        #endif
+      }
     }
 
     void _lcd_mesh_edit_NOP() {