Spacing cleanup

Marlin/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/default/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -378,29 +378,29 @@
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
   // Buda 2.0 on 24V
-  #define  DEFAULT_Kp 6
-  #define  DEFAULT_Ki .3
-  #define  DEFAULT_Kd 125
+  #define DEFAULT_Kp 6
+  #define DEFAULT_Ki .3
+  #define DEFAULT_Kd 125
 
   // Buda 2.0 on 12V
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.01
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.01
+  //#define DEFAULT_Kd 114
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -431,27 +431,27 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //24V 360W silicone heater from NPH on 3mm borosilicate (TAZ 2.2+)
-  #define  DEFAULT_bedKp 20
-  #define  DEFAULT_bedKi 5
-  #define  DEFAULT_bedKd 275
+  #define DEFAULT_bedKp 20
+  #define DEFAULT_bedKi 5
+  #define DEFAULT_bedKd 275
 
   //12v 400W silicone heater from QUDB into 3mm borosilicate (TAZ 1.0+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 650
-  //#define  DEFAULT_bedKi 60
-  //#define  DEFAULT_bedKd 1800
+  //#define DEFAULT_bedKp 650
+  //#define DEFAULT_bedKi 60
+  //#define DEFAULT_bedKd 1800
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -379,30 +379,30 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // ANET A6 Firmware V2.0 Standard Extruder defaults:
   // PID-P: +022.20, PID-I: +001.08, PID-D: +114.00, PID-C: 1
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114.0
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114.0
 
   // Tuned by ralf-e. Always re-tune for your machine!
-  #define  DEFAULT_Kp 16.83
-  #define  DEFAULT_Ki 1.02
-  #define  DEFAULT_Kd 69.29
+  #define DEFAULT_Kp 16.83
+  #define DEFAULT_Ki 1.02
+  #define DEFAULT_Kd 69.29
 
 #endif // PIDTEMP
 
@@ -434,24 +434,24 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // ANET A6
   // original Bed + 0.3mm Heat conducting into 4mm borosilicate (PID-Autotune: M303 E-1 S60 C5):
-  //#define  DEFAULT_bedKp 295.00
-  //#define  DEFAULT_bedKi 35.65
-  //#define  DEFAULT_bedKd 610.21
-  #define  DEFAULT_bedKp 295.00
-  #define  DEFAULT_bedKi 35.65
-  #define  DEFAULT_bedKd 610.21
+  //#define DEFAULT_bedKp 295.00
+  //#define DEFAULT_bedKi 35.65
+  //#define DEFAULT_bedKd 610.21
+  #define DEFAULT_bedKp 295.00
+  #define DEFAULT_bedKi 35.65
+  #define DEFAULT_bedKd 610.21
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -380,25 +380,25 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 21.0
-  //#define  DEFAULT_Ki 1.25
-  //#define  DEFAULT_Kd 86.0
+  //#define DEFAULT_Kp 21.0
+  //#define DEFAULT_Ki 1.25
+  //#define DEFAULT_Kd 86.0
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // ANET A8 Standard Extruder at 210 Degree Celsius and 100% Fan
   //(measured after M106 S255 with M303 E0 S210 C8)
-  #define  DEFAULT_Kp 21.0
-  #define  DEFAULT_Ki 1.25
-  #define  DEFAULT_Kd 86.0
+  #define DEFAULT_Kp 21.0
+  #define DEFAULT_Ki 1.25
+  #define DEFAULT_Kd 86.0
 
 #endif // PIDTEMP
 
@@ -430,15 +430,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 23.89
-  #define  DEFAULT_Ki 1.37
-  #define  DEFAULT_Kd 104.5
+  #define DEFAULT_Kp 23.89
+  #define DEFAULT_Ki 1.37
+  #define DEFAULT_Kd 104.5
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-    #define  DEFAULT_bedKp 23.89
-    #define  DEFAULT_bedKi 1.37
-    #define  DEFAULT_bedKd 104.5
+    #define DEFAULT_bedKp 23.89
+    #define DEFAULT_bedKi 1.37
+    #define DEFAULT_bedKd 104.5
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 23.89
-  #define  DEFAULT_Ki 1.37
-  #define  DEFAULT_Kd 104.5
+  #define DEFAULT_Kp 23.89
+  #define DEFAULT_Ki 1.37
+  #define DEFAULT_Kd 104.5
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-    #define  DEFAULT_bedKp 23.89
-    #define  DEFAULT_bedKi 1.37
-    #define  DEFAULT_bedKd 104.5
+    #define DEFAULT_bedKp 23.89
+    #define DEFAULT_bedKi 1.37
+    #define DEFAULT_bedKd 104.5
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -377,9 +377,9 @@
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Hephestos i3
-  #define  DEFAULT_Kp 23.05
-  #define  DEFAULT_Ki 2.00
-  #define  DEFAULT_Kd 66.47
+  #define DEFAULT_Kp 23.05
+  #define DEFAULT_Ki 2.00
+  #define DEFAULT_Kd 66.47
 
 #endif // PIDTEMP
 
@@ -411,15 +411,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -385,14 +385,14 @@
                                     // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Tuned PID values using M303
-  #define  DEFAULT_Kp 19.18
-  #define  DEFAULT_Ki 1.36
-  #define  DEFAULT_Kd 67.42
+  #define DEFAULT_Kp 19.18
+  #define DEFAULT_Ki 1.36
+  #define DEFAULT_Kd 67.42
 
   // BQ firmware stock PID values
-  //#define  DEFAULT_Kp 10.7
-  //#define  DEFAULT_Ki 0.45
-  //#define  DEFAULT_Kd 3
+  //#define DEFAULT_Kp 10.7
+  //#define DEFAULT_Ki 0.45
+  //#define DEFAULT_Kd 3
 
 #endif // PIDTEMP
 
@@ -424,15 +424,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -377,9 +377,9 @@
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Witbox
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
 #endif // PIDTEMP
 
@@ -411,15 +411,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -380,19 +380,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
     // Cartesio extruderV6 40W Normal
-    #define  DEFAULT_Kp 18
-    #define  DEFAULT_Ki 1
-    #define  DEFAULT_Kd 100
+    #define DEFAULT_Kp 18
+    #define DEFAULT_Ki 1
+    #define DEFAULT_Kd 100
 
     // Cartesio extruderV6 40W Volcano
-    //#define  DEFAULT_Kp 50
-    //#define  DEFAULT_Ki 9
-    //#define  DEFAULT_Kd 70
+    //#define DEFAULT_Kp 50
+    //#define DEFAULT_Ki 9
+    //#define DEFAULT_Kd 70
 
     // Cartesio extruderV6 40W Cyclops
-    //#define  DEFAULT_Kp 18
-    //#define  DEFAULT_Ki 1
-    //#define  DEFAULT_Kd 100
+    //#define DEFAULT_Kp 18
+    //#define DEFAULT_Ki 1
+    //#define DEFAULT_Kd 100
 
 #endif // PIDTEMP
 
@@ -423,14 +423,14 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
     //24V 500W silicone heater on to 4mm glass CartesioW
-    #define  DEFAULT_bedKp 390
-    #define  DEFAULT_bedKi 70
-    #define  DEFAULT_bedKd 546
+    #define DEFAULT_bedKp 390
+    #define DEFAULT_bedKi 70
+    #define DEFAULT_bedKd 546
 
     //24V 250W silicone heater on to 4mm glass CartesioM
-    //#define  DEFAULT_bedKp 303
-    //#define  DEFAULT_bedKi 42
-    //#define  DEFAULT_bedKd 539
+    //#define DEFAULT_bedKp 303
+    //#define DEFAULT_bedKi 42
+    //#define DEFAULT_bedKd 539
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -379,24 +379,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Stock CR-10 tuned for 70C
-  #define  DEFAULT_Kp 22.57
-  #define  DEFAULT_Ki 1.72
-  #define  DEFAULT_Kd 73.96
+  #define DEFAULT_Kp 22.57
+  #define DEFAULT_Ki 1.72
+  #define DEFAULT_Kd 73.96
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -427,21 +427,21 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //Stock CR-10 Bed Tuned for 70C
-  #define  DEFAULT_bedKp 426.68
-  #define  DEFAULT_bedKi 78.92
-  #define  DEFAULT_bedKd 576.71
+  #define DEFAULT_bedKp 426.68
+  #define DEFAULT_bedKi 78.92
+  #define DEFAULT_bedKd 576.71
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

@@ -388,24 +388,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Stock CR-10 tuned for 70C
-  #define  DEFAULT_Kp 22.57
-  #define  DEFAULT_Ki 1.72
-  #define  DEFAULT_Kd 73.96
+  #define DEFAULT_Kp 22.57
+  #define DEFAULT_Ki 1.72
+  #define DEFAULT_Kd 73.96
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -436,21 +436,21 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //Stock CR-10 Bed Tuned for 70C
-  #define  DEFAULT_bedKp 426.68
-  #define  DEFAULT_bedKi 78.92
-  #define  DEFAULT_bedKd 576.71
+  #define DEFAULT_bedKp 426.68
+  #define DEFAULT_bedKi 78.92
+  #define DEFAULT_bedKd 576.71
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Creality/Ender-2/Configuration.h

@@ -378,24 +378,24 @@
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
   // Creality Ender
-  #define  DEFAULT_Kp 21.73
-  #define  DEFAULT_Ki 1.54
-  #define  DEFAULT_Kd 76.55
+  #define DEFAULT_Kp 21.73
+  #define DEFAULT_Ki 1.54
+  #define DEFAULT_Kd 76.55
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -427,15 +427,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Creality/Ender-4/Configuration.h

@@ -379,24 +379,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ender-4
-  #define  DEFAULT_Kp 22.57
-  #define  DEFAULT_Ki 1.72
-  #define  DEFAULT_Kd 73.96
+  #define DEFAULT_Kp 22.57
+  #define DEFAULT_Ki 1.72
+  #define DEFAULT_Kd 73.96
 
   // Ultimaker
-//  #define  DEFAULT_Kp 22.2
-//  #define  DEFAULT_Ki 1.08
-//  #define  DEFAULT_Kd 114
+//  #define DEFAULT_Kp 22.2
+//  #define DEFAULT_Ki 1.08
+//  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -427,21 +427,21 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   // Ender-4
-  #define  DEFAULT_bedKp 426.68
-  #define  DEFAULT_bedKi 78.92
-  #define  DEFAULT_bedKd 576.71
+  #define DEFAULT_bedKp 426.68
+  #define DEFAULT_bedKi 78.92
+  #define DEFAULT_bedKd 576.71
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -380,24 +380,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // FolgerTech i3-2020
-  #define  DEFAULT_Kp 11.50
-  #define  DEFAULT_Ki 0.50
-  #define  DEFAULT_Kd 60.00
+  #define DEFAULT_Kp 11.50
+  #define DEFAULT_Ki 0.50
+  #define DEFAULT_Kd 60.00
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -429,15 +429,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 250.0
-  #define  DEFAULT_bedKi 18.0
-  #define  DEFAULT_bedKd 950.0
+  #define DEFAULT_bedKp 250.0
+  #define DEFAULT_bedKi 18.0
+  #define DEFAULT_bedKd 950.0
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -377,31 +377,31 @@
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Geeetech MK8 Extruder
-  #define  DEFAULT_Kp 12.33
-  #define  DEFAULT_Ki 0.51
-  #define  DEFAULT_Kd 74.50
+  #define DEFAULT_Kp 12.33
+  #define DEFAULT_Ki 0.51
+  #define DEFAULT_Kd 74.50
 
   // CTC MK8 Extruder
-  //#define  DEFAULT_Kp 19.86
-  //#define  DEFAULT_Ki 1.0
-  //#define  DEFAULT_Kd 98.83
+  //#define DEFAULT_Kp 19.86
+  //#define DEFAULT_Ki 1.0
+  //#define DEFAULT_Kd 98.83
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -432,21 +432,21 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X)
-  #define  DEFAULT_bedKp 234.88
-  #define  DEFAULT_bedKi 42.79
-  #define  DEFAULT_bedKd 322.28
+  #define DEFAULT_bedKp 234.88
+  #define DEFAULT_bedKi 42.79
+  #define DEFAULT_bedKd 322.28
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -377,31 +377,31 @@
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Geeetech MK8 Extruder
-  #define  DEFAULT_Kp 12.33
-  #define  DEFAULT_Ki 0.51
-  #define  DEFAULT_Kd 74.50
+  #define DEFAULT_Kp 12.33
+  #define DEFAULT_Ki 0.51
+  #define DEFAULT_Kd 74.50
 
   // CTC MK8 Extruder
-  //#define  DEFAULT_Kp 19.86
-  //#define  DEFAULT_Ki 1.0
-  //#define  DEFAULT_Kd 98.83
+  //#define DEFAULT_Kp 19.86
+  //#define DEFAULT_Ki 1.0
+  //#define DEFAULT_Kd 98.83
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -432,21 +432,21 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X)
-  #define  DEFAULT_bedKp 234.88
-  #define  DEFAULT_bedKi 42.79
-  #define  DEFAULT_bedKd 322.28
+  #define DEFAULT_bedKp 234.88
+  #define DEFAULT_bedKi 42.79
+  #define DEFAULT_bedKd 322.28
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -377,31 +377,31 @@
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Geeetech MK8 Extruder
-  #define  DEFAULT_Kp 12.33
-  #define  DEFAULT_Ki 0.51
-  #define  DEFAULT_Kd 74.50
+  #define DEFAULT_Kp 12.33
+  #define DEFAULT_Ki 0.51
+  #define DEFAULT_Kd 74.50
 
   // CTC MK8 Extruder
-  //#define  DEFAULT_Kp 19.86
-  //#define  DEFAULT_Ki 1.0
-  //#define  DEFAULT_Kd 98.83
+  //#define DEFAULT_Kp 19.86
+  //#define DEFAULT_Ki 1.0
+  //#define DEFAULT_Kd 98.83
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -432,21 +432,21 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X)
-  #define  DEFAULT_bedKp 234.88
-  #define  DEFAULT_bedKi 42.79
-  #define  DEFAULT_bedKd 322.28
+  #define DEFAULT_bedKp 234.88
+  #define DEFAULT_bedKi 42.79
+  #define DEFAULT_bedKd 322.28
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -379,23 +379,23 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
-  #define  DEFAULT_Kp 213.2
-  #define  DEFAULT_Ki 1.54
-  #define  DEFAULT_Kd 765
+  #define DEFAULT_Kp 213.2
+  #define DEFAULT_Ki 1.54
+  #define DEFAULT_Kd 765
 
 #endif // PIDTEMP
 
@@ -427,15 +427,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/JGAurora/A5/Configuration.h

@@ -384,24 +384,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // JGAurora A5 (tuned at 210C)
-  #define  DEFAULT_Kp 35.3//22.2
-  #define  DEFAULT_Ki 4.35//1.08
-  #define  DEFAULT_Kd 71.57//114
+  #define DEFAULT_Kp 35.3//22.2
+  #define DEFAULT_Ki 4.35//1.08
+  #define DEFAULT_Kd 71.57//114
 
 #endif // PIDTEMP
 
@@ -435,15 +435,15 @@
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
 
   // JGAurora A5 (tuned at 70C)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/MakerParts/Configuration.h

@@ -399,19 +399,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -443,15 +443,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -387,19 +387,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Malyan M150 example
-  #define  DEFAULT_Kp 29
-  #define  DEFAULT_Ki 2
-  #define  DEFAULT_Kd 97
+  #define DEFAULT_Kp 29
+  #define DEFAULT_Ki 2
+  #define DEFAULT_Kd 97
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -431,15 +431,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Malyan/M200/Configuration.h

@@ -383,14 +383,14 @@
   #define DEFAULT_Ki 2.74
   #define DEFAULT_Kd 62.35
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -428,9 +428,9 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -382,19 +382,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Rigidbot hotend
-  #define  DEFAULT_Kp 16.17
-  #define  DEFAULT_Ki 0.85
-  #define  DEFAULT_Kd 76.55
+  #define DEFAULT_Kp 16.17
+  #define DEFAULT_Ki 0.85
+  #define DEFAULT_Kd 76.55
 
   // Base DGlass3D/E3Dv6 hotend
-  //#define  DEFAULT_Kp 10
-  //#define  DEFAULT_Ki 0.85
-  //#define  DEFAULT_Kd 245
+  //#define DEFAULT_Kp 10
+  //#define DEFAULT_Ki 0.85
+  //#define DEFAULT_Kd 245
 
   // E3D w/ rigidbot cartridge
-  //#define  DEFAULT_Kp 16.30
-  //#define  DEFAULT_Ki 0.95
-  //#define  DEFAULT_Kd 69.69
+  //#define DEFAULT_Kp 16.30
+  //#define DEFAULT_Ki 0.95
+  //#define DEFAULT_Kd 69.69
 
 #endif // PIDTEMP
 
@@ -425,9 +425,9 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //RigidBot, from pid autotune
-  #define  DEFAULT_bedKp 355
-  #define  DEFAULT_bedKi 66.5
-  #define  DEFAULT_bedKd 480
+  #define DEFAULT_bedKp 355
+  #define DEFAULT_bedKi 66.5
+  #define DEFAULT_bedKd 480
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/SCARA/Configuration.h

@@ -406,9 +406,9 @@
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Merlin Hotend: From Autotune
-  #define  DEFAULT_Kp 24.5
-  #define  DEFAULT_Ki 1.72
-  #define  DEFAULT_Kd 87.73
+  #define DEFAULT_Kp 24.5
+  #define DEFAULT_Ki 1.72
+  #define DEFAULT_Kd 87.73
 
 #endif // PIDTEMP
 
@@ -440,9 +440,9 @@
 
   //12v Heatbed Mk3 12V in parallel
   //from pidautotune
-  #define  DEFAULT_bedKp 630.14
-  #define  DEFAULT_bedKi 121.71
-  #define  DEFAULT_bedKd 815.64
+  #define DEFAULT_bedKp 630.14
+  #define DEFAULT_bedKi 121.71
+  #define DEFAULT_bedKd 815.64
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -380,19 +380,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -424,15 +424,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/TheBorg/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 18.21
-  #define  DEFAULT_Ki 1.42
-  #define  DEFAULT_Kd 58.34
+  #define DEFAULT_Kp 18.21
+  #define DEFAULT_Ki 1.42
+  #define DEFAULT_Kd 58.34
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 554.16
-  #define  DEFAULT_bedKi 64.07
-  #define  DEFAULT_bedKd 1198.25
+  #define DEFAULT_bedKp 554.16
+  #define DEFAULT_bedKi 64.07
+  #define DEFAULT_bedKd 1198.25
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -406,30 +406,30 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // TinyBoy2 Extruder - calculated with PID Autotune and tested
   // "M303 E0 C8 S200"
-  //#define  DEFAULT_Kp 25.63
-  //#define  DEFAULT_Ki 2.66
-  //#define  DEFAULT_Kd 61.73
+  //#define DEFAULT_Kp 25.63
+  //#define DEFAULT_Ki 2.66
+  //#define DEFAULT_Kd 61.73
 
   // TinyBoy2 Extruder - same, but with fan @ 25% duty
-  #define  DEFAULT_Kp 26.15
-  #define  DEFAULT_Ki 2.71
-  #define  DEFAULT_Kd 63.02
+  #define DEFAULT_Kp 26.15
+  #define DEFAULT_Ki 2.71
+  #define DEFAULT_Kd 63.02
 #endif // PIDTEMP
 
 //===========================================================================
@@ -460,29 +460,29 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 
   // TinyBoy2 heatbed - calculated with PID Autotune and tested
   // "M303 E-1 C8 S75"
-  //#define  DEFAULT_bedKp 421.80
-  //#define  DEFAULT_bedKi 82.51
-  //#define  DEFAULT_bedKd 539.06
+  //#define DEFAULT_bedKp 421.80
+  //#define DEFAULT_bedKi 82.51
+  //#define DEFAULT_bedKd 539.06
 
   // TinyBoy2 heatbed - same, but with fan @ 25% duty
   // "M303 E-1 C8 S75"
-  #define  DEFAULT_bedKp 267.54
-  #define  DEFAULT_bedKi 52.34
-  #define  DEFAULT_bedKd 341.92
+  #define DEFAULT_bedKp 267.54
+  #define DEFAULT_bedKi 52.34
+  #define DEFAULT_bedKd 341.92
 
 #endif // PIDTEMPBED
 

Marlin/src/config/examples/Tronxy/X1/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Tronxy X1
-  #define  DEFAULT_Kp 16.20
-  #define  DEFAULT_Ki 1.11
-  #define  DEFAULT_Kd 59.06
+  #define DEFAULT_Kp 16.20
+  #define DEFAULT_Ki 1.11
+  #define DEFAULT_Kd 59.06
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Tronxy/X5S/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Tronxy/XY100/Configuration.h

@@ -379,30 +379,30 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  // #define  DEFAULT_Kp 22.2
-  // #define  DEFAULT_Ki 1.08
-  // #define  DEFAULT_Kd 114
+  // #define DEFAULT_Kp 22.2
+  // #define DEFAULT_Ki 1.08
+  // #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // TronXY XY-100 Standard Extruder at 210 Degree Celsius and 100% Fan
   // (measured after M106 S255 with M303 E0 S210 C8)
-  // #define  DEFAULT_Kp 20.32
-  // #define  DEFAULT_Ki 1.18
-  // #define  DEFAULT_Kd 87.80
+  // #define DEFAULT_Kp 20.32
+  // #define DEFAULT_Ki 1.18
+  // #define DEFAULT_Kd 87.80
 
   // TronXY XY-100 Standard Extruder, from original firmware
-  #define  DEFAULT_Kp 7.0000
-  #define  DEFAULT_Ki 2.0000
-  #define  DEFAULT_Kd 40.0000
+  #define DEFAULT_Kp 7.0000
+  #define DEFAULT_Ki 2.0000
+  #define DEFAULT_Kd 40.0000
 
 #endif // PIDTEMP
 
@@ -434,15 +434,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -399,24 +399,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // Vellemann K8200 Extruder - calculated with PID Autotune and tested
-  #define  DEFAULT_Kp 24.29
-  #define  DEFAULT_Ki 1.58
-  #define  DEFAULT_Kd 93.51
+  #define DEFAULT_Kp 24.29
+  #define DEFAULT_Ki 1.58
+  #define DEFAULT_Kd 93.51
 #endif // PIDTEMP
 
 //===========================================================================
@@ -447,23 +447,23 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 
     // Vellemann K8200 PCB heatbed with standard PCU at 60 degreesC - calculated with PID Autotune and tested
     // from pidautotune
-    #define  DEFAULT_bedKp 341.88
-    #define  DEFAULT_bedKi 25.32
-    #define  DEFAULT_bedKd 1153.89
+    #define DEFAULT_bedKp 341.88
+    #define DEFAULT_bedKi 25.32
+    #define DEFAULT_bedKd 1153.89
 #endif // PIDTEMPBED
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  #define  DEFAULT_Kp 63.0
-  #define  DEFAULT_Ki 2.25
-  #define  DEFAULT_Kd 440
+  #define DEFAULT_Kp 63.0
+  #define DEFAULT_Ki 2.25
+  #define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  #define  DEFAULT_Kp 63.0
-  #define  DEFAULT_Ki 2.25
-  #define  DEFAULT_Kd 440
+  #define DEFAULT_Kp 63.0
+  #define DEFAULT_Ki 2.25
+  #define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -379,24 +379,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // Duplicator 6
-  #define  DEFAULT_Kp 9.12
-  #define  DEFAULT_Ki 0.41
-  #define  DEFAULT_Kd 50.98
+  #define DEFAULT_Kp 9.12
+  #define DEFAULT_Ki 0.41
+  #define DEFAULT_Kd 50.98
 
 #endif // PIDTEMP
 
@@ -428,20 +428,20 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-//  #define  DEFAULT_bedKp 10.00
-//  #define  DEFAULT_bedKi .023
-//  #define  DEFAULT_bedKd 305.4
+//  #define DEFAULT_bedKp 10.00
+//  #define DEFAULT_bedKi .023
+//  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // Duplicator 6
-  #define  DEFAULT_bedKp 124.55
-  #define  DEFAULT_bedKi 23.46
-  #define  DEFAULT_bedKd 165.29
+  #define DEFAULT_bedKp 124.55
+  #define DEFAULT_bedKi 23.46
+  #define DEFAULT_bedKd 165.29
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -379,24 +379,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   //E3D with 30MM fan
-  #define  DEFAULT_Kp 24.77
-  #define  DEFAULT_Ki 1.84
-  #define  DEFAULT_Kd 83.61
+  #define DEFAULT_Kp 24.77
+  #define DEFAULT_Ki 1.84
+  #define DEFAULT_Kd 83.61
 
 #endif // PIDTEMP
 
@@ -428,20 +428,20 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   //D-force
-  #define  DEFAULT_bedKp 22.97
-  #define  DEFAULT_bedKi 3.76
-  #define  DEFAULT_bedKd 29.2
+  #define DEFAULT_bedKp 22.97
+  #define DEFAULT_bedKi 3.76
+  #define DEFAULT_bedKd 29.2
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h

@@ -379,24 +379,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   //E3D with 30MM fan
-  #define  DEFAULT_Kp 24.77
-  #define  DEFAULT_Ki 1.84
-  #define  DEFAULT_Kd 83.61
+  #define DEFAULT_Kp 24.77
+  #define DEFAULT_Ki 1.84
+  #define DEFAULT_Kd 83.61
 
 #endif // PIDTEMP
 
@@ -428,20 +428,20 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   //D-force
-  #define  DEFAULT_bedKp 22.97
-  #define  DEFAULT_bedKi 3.76
-  #define  DEFAULT_bedKd 29.2
+  #define DEFAULT_bedKp 22.97
+  #define DEFAULT_bedKi 3.76
+  #define DEFAULT_bedKd 29.2
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -379,24 +379,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   //E3D with 30MM fan
-  #define  DEFAULT_Kp 24.77
-  #define  DEFAULT_Ki 1.84
-  #define  DEFAULT_Kd 83.61
+  #define DEFAULT_Kp 24.77
+  #define DEFAULT_Ki 1.84
+  #define DEFAULT_Kd 83.61
 
 #endif // PIDTEMP
 
@@ -428,20 +428,20 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   //D-force
-  #define  DEFAULT_bedKp 22.97
-  #define  DEFAULT_bedKi 3.76
-  #define  DEFAULT_bedKd 29.2
+  #define DEFAULT_bedKp 22.97
+  #define DEFAULT_bedKi 3.76
+  #define DEFAULT_bedKd 29.2
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h

@@ -384,24 +384,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
   // E3D-v6
-  #define  DEFAULT_Kp 18.55
-  #define  DEFAULT_Ki 2.71
-  #define  DEFAULT_Kd 47.69
+  #define DEFAULT_Kp 18.55
+  #define DEFAULT_Ki 2.71
+  #define DEFAULT_Kd 47.69
 
 #endif // PIDTEMP
 
@@ -433,20 +433,20 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
+  //#define DEFAULT_bedKp 10.00
+  //#define DEFAULT_bedKi .023
+  //#define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   //HatchBox Alpha
-  #define  DEFAULT_bedKp 72.11
-  #define  DEFAULT_bedKi 7.1
-  #define  DEFAULT_bedKd 488.31
+  #define DEFAULT_bedKp 72.11
+  #define DEFAULT_bedKi 7.1
+  #define DEFAULT_bedKd 488.31
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -423,15 +423,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -381,9 +381,9 @@
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Kossel Pro
-  #define  DEFAULT_Kp 19.30
-  #define  DEFAULT_Ki 3.51
-  #define  DEFAULT_Kd 26.56
+  #define DEFAULT_Kp 19.30
+  #define DEFAULT_Ki 3.51
+  #define DEFAULT_Kd 26.56
 
 #endif // PIDTEMP
 
@@ -415,9 +415,9 @@
 
   //Kossel Pro heated bed plate with borosilicate glass
   //from pidautotune (M303 E-1 S60 C8)
-  #define  DEFAULT_bedKp 370.25
-  #define  DEFAULT_bedKi 62.77
-  #define  DEFAULT_bedKd 545.98
+  #define DEFAULT_bedKp 370.25
+  #define DEFAULT_bedKi 62.77
+  #define DEFAULT_bedKd 545.98
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -388,14 +388,14 @@
   //#define DEFAULT_Kd 85.30
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -427,15 +427,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 15.00
-  #define  DEFAULT_bedKi .04
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 15.00
+  #define DEFAULT_bedKi .04
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -387,24 +387,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // gMax J-Head
-  #define  DEFAULT_Kp 15.35
-  #define  DEFAULT_Ki 0.85
-  #define  DEFAULT_Kd 69.45
+  #define DEFAULT_Kp 15.35
+  #define DEFAULT_Ki 0.85
+  #define DEFAULT_Kd 69.45
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -436,15 +436,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 135.44
-  #define  DEFAULT_bedKi 24.60
-  #define  DEFAULT_bedKd 186.40
+  #define DEFAULT_bedKp 135.44
+  #define DEFAULT_bedKi 24.60
+  #define DEFAULT_bedKd 186.40
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/makibox/Configuration.h

@@ -379,19 +379,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -426,15 +426,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/stm32f103ret6/Configuration.h

@@ -380,19 +380,19 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define  DEFAULT_Kp 22.2
-  #define  DEFAULT_Ki 1.08
-  #define  DEFAULT_Kd 114
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -424,15 +424,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -378,9 +378,9 @@
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
   // J-Head Mk V-B
-  #define  DEFAULT_Kp 25.05
-  #define  DEFAULT_Ki 2.30
-  #define  DEFAULT_Kd 68.15
+  #define DEFAULT_Kp 25.05
+  #define DEFAULT_Ki 2.30
+  #define DEFAULT_Kd 68.15
 
 #endif // PIDTEMP
 
@@ -412,15 +412,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/wt150/Configuration.h

@@ -379,24 +379,24 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   //WT150, based on: M303 E0 S220 C8
-  #define  DEFAULT_Kp 22.10
-  #define  DEFAULT_Ki 1.10
-  #define  DEFAULT_Kd 110.78
+  #define DEFAULT_Kp 22.10
+  #define DEFAULT_Ki 1.10
+  #define DEFAULT_Kd 110.78
 
   // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
 
   // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
 
 #endif // PIDTEMP
 
@@ -428,15 +428,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define  DEFAULT_bedKp 10.00
-  #define  DEFAULT_bedKi .023
-  #define  DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -1208,7 +1208,7 @@
    *   stepperY.interpolate(0); \
    * }
    */
-  #define  TMC_ADV() {  }
+  #define TMC_ADV() {  }
 
 #endif // TMC2130 || TMC2208
 

Marlin/src/module/temperature.cpp

@@ -452,17 +452,17 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS],
 
         #if HAS_PID_FOR_BOTH
           const char* estring = hotend < 0 ? "bed" : "";
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kp ", workKp); SERIAL_EOL();
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Ki ", workKi); SERIAL_EOL();
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kd ", workKd); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kp ", workKp); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Ki ", workKi); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kd ", workKd); SERIAL_EOL();
         #elif ENABLED(PIDTEMP)
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_Kp ", workKp); SERIAL_EOL();
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_Ki ", workKi); SERIAL_EOL();
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_Kd ", workKd); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_Kp ", workKp); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_Ki ", workKi); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_Kd ", workKd); SERIAL_EOL();
         #else
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_bedKp ", workKp); SERIAL_EOL();
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_bedKi ", workKi); SERIAL_EOL();
-          SERIAL_PROTOCOLPAIR("#define  DEFAULT_bedKd ", workKd); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKp ", workKp); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKi ", workKi); SERIAL_EOL();
+          SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKd ", workKd); SERIAL_EOL();
         #endif
 
         #define _SET_BED_PID() do { \

Marlin/src/module/tool_change.cpp

@@ -503,7 +503,7 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
         #else
           constexpr bool safe_to_move = true;
         #endif
- 
+
         // Move to the "old position" (move the extruder into place)
         #if ENABLED(SWITCHING_NOZZLE)
           destination[Z_AXIS] += z_diff;  // Include the Z restore with the "move back"

Marlin/src/pins/pins_AZTEEG_X3_PRO.h

@@ -140,7 +140,7 @@
   #undef SD_DETECT_PIN
   #define SD_DETECT_PIN    49   // For easy adapter board
   #undef BEEPER_PIN
-  #define  BEEPER_PIN      12   // 33 isn't physically available to the LCD display
+  #define BEEPER_PIN       12   // 33 isn't physically available to the LCD display
 #else
   #define STAT_LED_RED_PIN  32
   #define STAT_LED_BLUE_PIN 35