Upgrade BigTrees to latest platform ststm32 (#15285)

buildroot/share/PlatformIO/boards/BigTree_SKR_Pro.json

@@ -2,7 +2,7 @@
   "build": {
     "core": "stm32",
     "cpu": "cortex-m4",
-    "extra_flags": "-DSTM32F407xx",
+    "extra_flags": "-DSTM32F4 -DSTM32F407xx -DSTM32F40_41xxx",
     "f_cpu": "168000000L",
     "hwids": [
       [
@@ -21,28 +21,11 @@
   "debug": {
     "jlink_device": "STM32F407ZG",
     "openocd_target": "stm32f4x",
-    "svd_path": "STM32F40x.svd",
-    "tools": {
-      "stlink": {
-        "server": {
-          "arguments": [
-            "-f",
-            "scripts/interface/stlink.cfg",
-            "-c",
-            "transport select hla_swd",
-            "-f",
-            "scripts/target/stm32f4x.cfg",
-            "-c",
-            "reset_config none"
-          ],
-          "executable": "bin/openocd",
-          "package": "tool-openocd"
-        }
-      }
-    }
+    "svd_path": "STM32F40x.svd"
   },
   "frameworks": [
     "arduino",
+    "cmsis",
     "stm32cube"
   ],
   "name": "STM32F407ZG (192k RAM. 1024k Flash)",

buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/stm32f4xx_hal_conf.h

@@ -1,481 +0,0 @@
-/**
-  ******************************************************************************
-  * @file    stm32f4xx_hal_conf.h
-  * @brief   HAL configuration file.
-  ******************************************************************************
-  * @attention
-  *
-  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
-  * All rights reserved.</center></h2>
-  *
-  * This software component is licensed by ST under BSD 3-Clause license,
-  * the "License"; You may not use this file except in compliance with the
-  * License. You may obtain a copy of the License at:
-  *                        opensource.org/licenses/BSD-3-Clause
-  *
-  ******************************************************************************
-  */
-
-/* Define to prevent recursive inclusion -------------------------------------*/
-#ifndef __STM32F4xx_HAL_CONF_H
-#define __STM32F4xx_HAL_CONF_H
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* Exported types ------------------------------------------------------------*/
-/* Exported constants --------------------------------------------------------*/
-
-/* ########################## Module Selection ############################## */
- /**
-  * @brief This is the list of modules to be used in the HAL driver
-  */
-#define HAL_MODULE_ENABLED
-#define HAL_ADC_MODULE_ENABLED
-/* #define HAL_CAN_MODULE_ENABLED   */
-/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
-#define HAL_CRC_MODULE_ENABLED
-/* #define HAL_CEC_MODULE_ENABLED   */
-/* #define HAL_CRYP_MODULE_ENABLED   */
-#define HAL_DAC_MODULE_ENABLED
-/* #define HAL_DCMI_MODULE_ENABLED   */
-#define HAL_DMA_MODULE_ENABLED
-/* #define HAL_DMA2D_MODULE_ENABLED   */
-/* #define HAL_ETH_MODULE_ENABLED   */
-#define HAL_FLASH_MODULE_ENABLED
-/* #define HAL_NAND_MODULE_ENABLED   */
-/* #define HAL_NOR_MODULE_ENABLED   */
-/* #define HAL_PCCARD_MODULE_ENABLED   */
-/* #define HAL_SRAM_MODULE_ENABLED   */
-/* #define HAL_SDRAM_MODULE_ENABLED   */
-/* #define HAL_HASH_MODULE_ENABLED   */
-#define HAL_GPIO_MODULE_ENABLED
-/* #define HAL_EXTI_MODULE_ENABLED   */
-#define HAL_I2C_MODULE_ENABLED
-/* #define HAL_SMBUS_MODULE_ENABLED   */
-/* #define HAL_I2S_MODULE_ENABLED   */
-/* #define HAL_IWDG_MODULE_ENABLED   */
-/* #define HAL_LTDC_MODULE_ENABLED   */
-/* #define HAL_DSI_MODULE_ENABLED   */
-#define HAL_PWR_MODULE_ENABLED
-/* #define HAL_QSPI_MODULE_ENABLED   */
-#define HAL_RCC_MODULE_ENABLED
-/* #define HAL_RNG_MODULE_ENABLED   */
-#define HAL_RTC_MODULE_ENABLED
-/* #define HAL_SAI_MODULE_ENABLED   */
-#define HAL_SD_MODULE_ENABLED
-#define HAL_SPI_MODULE_ENABLED
-#define HAL_TIM_MODULE_ENABLED
-/* #define HAL_UART_MODULE_ENABLED   */
-/* #define HAL_USART_MODULE_ENABLED   */
-/* #define HAL_IRDA_MODULE_ENABLED   */
-/* #define HAL_SMARTCARD_MODULE_ENABLED   */
-/* #define HAL_WWDG_MODULE_ENABLED   */
-#define HAL_CORTEX_MODULE_ENABLED
-#define HAL_PCD_MODULE_ENABLED
-/* #define HAL_HCD_MODULE_ENABLED   */
-/* #define HAL_FMPI2C_MODULE_ENABLED   */
-/* #define HAL_SPDIFRX_MODULE_ENABLED   */
-/* #define HAL_DFSDM_MODULE_ENABLED   */
-/* #define HAL_LPTIM_MODULE_ENABLED   */
-/* #define HAL_MMC_MODULE_ENABLED   */
-
-/* ########################## HSE/HSI Values adaptation ##################### */
- /**
-  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
-  *        This value is used by the RCC HAL module to compute the system frequency
-  *        (when HSE is used as system clock source, directly or through the PLL).
-  */
-#ifndef HSE_VALUE
-#define HSE_VALUE    ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#ifndef HSE_STARTUP_TIMEOUT
-#define HSE_STARTUP_TIMEOUT    ((uint32_t)100U)   /*!< Time out for HSE start up, in ms */
-#endif /* HSE_STARTUP_TIMEOUT */
-
- /**
-  * @brief Internal High Speed oscillator (HSI) value.
-  *        This value is used by the RCC HAL module to compute the system frequency
-  *        (when HSI is used as system clock source, directly or through the PLL).
-  */
-#ifndef HSI_VALUE
-#define HSI_VALUE    ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
- /**
-  * @brief Internal Low Speed oscillator (LSI) value.
-  */
-#ifndef LSI_VALUE
-#define LSI_VALUE  ((uint32_t)32000U)       /*!< LSI Typical Value in Hz*/
-#endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
-The real value may vary depending on the variations
-in voltage and temperature.*/
- /**
-  * @brief External Low Speed oscillator (LSE) value.
-  */
-#ifndef LSE_VALUE
-#define LSE_VALUE  ((uint32_t)32768U)    /*!< Value of the External Low Speed oscillator in Hz */
-#endif /* LSE_VALUE */
-
-#ifndef LSE_STARTUP_TIMEOUT
-#define LSE_STARTUP_TIMEOUT    ((uint32_t)5000U)   /*!< Time out for LSE start up, in ms */
-#endif /* LSE_STARTUP_TIMEOUT */
-
- /**
-  * @brief External clock source for I2S peripheral
-  *        This value is used by the I2S HAL module to compute the I2S clock source
-  *        frequency, this source is inserted directly through I2S_CKIN pad.
-  */
-#ifndef EXTERNAL_CLOCK_VALUE
-#define EXTERNAL_CLOCK_VALUE    ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/
-#endif /* EXTERNAL_CLOCK_VALUE */
-
-/* Tip: To avoid modifying this file each time you need to use different HSE,
-   ===  you can define the HSE value in your toolchain compiler preprocessor. */
-
-/* ########################### System Configuration ######################### */
- /**
-  * @brief This is the HAL system configuration section
-  */
-#define  VDD_VALUE          ((uint32_t)3300U) /*!< Value of VDD in mv */
-#define  TICK_INT_PRIORITY            ((uint32_t)0U)   /*!< tick interrupt priority */
-#define  USE_RTOS                     0U
-#define  PREFETCH_ENABLE              1U
-#define  INSTRUCTION_CACHE_ENABLE     1U
-#define  DATA_CACHE_ENABLE            1U
-
-#define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
-#define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
-#define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
-#define  USE_HAL_CRYP_REGISTER_CALLBACKS        0U /* CRYP register callback disabled      */
-#define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
-#define  USE_HAL_DCMI_REGISTER_CALLBACKS        0U /* DCMI register callback disabled      */
-#define  USE_HAL_DFSDM_REGISTER_CALLBACKS       0U /* DFSDM register callback disabled     */
-#define  USE_HAL_DMA2D_REGISTER_CALLBACKS       0U /* DMA2D register callback disabled     */
-#define  USE_HAL_DSI_REGISTER_CALLBACKS         0U /* DSI register callback disabled       */
-#define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
-#define  USE_HAL_HASH_REGISTER_CALLBACKS        0U /* HASH register callback disabled      */
-#define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
-#define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
-#define  USE_HAL_FMPI2C_REGISTER_CALLBACKS      0U /* FMPI2C register callback disabled    */
-#define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
-#define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
-#define  USE_HAL_LPTIM_REGISTER_CALLBACKS       0U /* LPTIM register callback disabled     */
-#define  USE_HAL_LTDC_REGISTER_CALLBACKS        0U /* LTDC register callback disabled      */
-#define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
-#define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
-#define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
-#define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
-#define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
-#define  USE_HAL_QSPI_REGISTER_CALLBACKS        0U /* QSPI register callback disabled      */
-#define  USE_HAL_RNG_REGISTER_CALLBACKS         0U /* RNG register callback disabled       */
-#define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
-#define  USE_HAL_SAI_REGISTER_CALLBACKS         0U /* SAI register callback disabled       */
-#define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
-#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
-#define  USE_HAL_SDRAM_REGISTER_CALLBACKS       0U /* SDRAM register callback disabled     */
-#define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
-#define  USE_HAL_SPDIFRX_REGISTER_CALLBACKS     0U /* SPDIFRX register callback disabled   */
-#define  USE_HAL_SMBUS_REGISTER_CALLBACKS       0U /* SMBUS register callback disabled     */
-#define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
-#define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
-#define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
-#define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
-#define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
-
-/* ########################## Assert Selection ############################## */
- /**
-  * @brief Uncomment the line below to expanse the "assert_param" macro in the
-  *        HAL drivers code
-  */
-/* #define USE_FULL_ASSERT    1U */
-
-/* ################## Ethernet peripheral configuration ##################### */
-
-/* Section 1 : Ethernet peripheral configuration */
-
-/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
-#define MAC_ADDR0   2U
-#define MAC_ADDR1   0U
-#define MAC_ADDR2   0U
-#define MAC_ADDR3   0U
-#define MAC_ADDR4   0U
-#define MAC_ADDR5   0U
-
-/* Definition of the Ethernet driver buffers size and count */
-#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
-#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
-#define ETH_RXBUFNB                    ((uint32_t)4U)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
-#define ETH_TXBUFNB                    ((uint32_t)4U)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
-
-/* Section 2: PHY configuration section */
-
-/* DP83848_PHY_ADDRESS Address*/
-#define DP83848_PHY_ADDRESS           0x01U
-/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
-#define PHY_RESET_DELAY                 ((uint32_t)0x000000FFU)
-/* PHY Configuration delay */
-#define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFFU)
-
-#define PHY_READ_TO                     ((uint32_t)0x0000FFFFU)
-#define PHY_WRITE_TO                    ((uint32_t)0x0000FFFFU)
-
-/* Section 3: Common PHY Registers */
-
-#define PHY_BCR                         ((uint16_t)0x0000U)    /*!< Transceiver Basic Control Register   */
-#define PHY_BSR                         ((uint16_t)0x0001U)    /*!< Transceiver Basic Status Register    */
-
-#define PHY_RESET                       ((uint16_t)0x8000U)  /*!< PHY Reset */
-#define PHY_LOOPBACK                    ((uint16_t)0x4000U)  /*!< Select loop-back mode */
-#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100U)  /*!< Set the full-duplex mode at 100 Mb/s */
-#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000U)  /*!< Set the half-duplex mode at 100 Mb/s */
-#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100U)  /*!< Set the full-duplex mode at 10 Mb/s  */
-#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000U)  /*!< Set the half-duplex mode at 10 Mb/s  */
-#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000U)  /*!< Enable auto-negotiation function     */
-#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200U)  /*!< Restart auto-negotiation function    */
-#define PHY_POWERDOWN                   ((uint16_t)0x0800U)  /*!< Select the power down mode           */
-#define PHY_ISOLATE                     ((uint16_t)0x0400U)  /*!< Isolate PHY from MII                 */
-
-#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020U)  /*!< Auto-Negotiation process completed   */
-#define PHY_LINKED_STATUS               ((uint16_t)0x0004U)  /*!< Valid link established               */
-#define PHY_JABBER_DETECTION            ((uint16_t)0x0002U)  /*!< Jabber condition detected            */
-
-/* Section 4: Extended PHY Registers */
-#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
-
-#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
-#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
-
-/* ################## SPI peripheral configuration ########################## */
-
-/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
-* Activated: CRC code is present inside driver
-* Deactivated: CRC code cleaned from driver
-*/
-
-#define USE_SPI_CRC                     0U
-
-/* Includes ------------------------------------------------------------------*/
- /**
-  * @brief Include module's header file
-  */
-
-#ifdef HAL_RCC_MODULE_ENABLED
-#include "stm32f4xx_hal_rcc.h"
-#endif /* HAL_RCC_MODULE_ENABLED */
-
-#ifdef HAL_GPIO_MODULE_ENABLED
-#include "stm32f4xx_hal_gpio.h"
-#endif /* HAL_GPIO_MODULE_ENABLED */
-
-#ifdef HAL_EXTI_MODULE_ENABLED
-#include "stm32f4xx_hal_exti.h"
-#endif /* HAL_EXTI_MODULE_ENABLED */
-
-#ifdef HAL_DMA_MODULE_ENABLED
-#include "stm32f4xx_hal_dma.h"
-#endif /* HAL_DMA_MODULE_ENABLED */
-
-#ifdef HAL_CORTEX_MODULE_ENABLED
-#include "stm32f4xx_hal_cortex.h"
-#endif /* HAL_CORTEX_MODULE_ENABLED */
-
-#ifdef HAL_ADC_MODULE_ENABLED
-#include "stm32f4xx_hal_adc.h"
-#endif /* HAL_ADC_MODULE_ENABLED */
-
-#ifdef HAL_CAN_MODULE_ENABLED
-#include "stm32f4xx_hal_can.h"
-#endif /* HAL_CAN_MODULE_ENABLED */
-
-#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
-#include "stm32f4xx_hal_can_legacy.h"
-#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
-
-#ifdef HAL_CRC_MODULE_ENABLED
-#include "stm32f4xx_hal_crc.h"
-#endif /* HAL_CRC_MODULE_ENABLED */
-
-#ifdef HAL_CRYP_MODULE_ENABLED
-#include "stm32f4xx_hal_cryp.h"
-#endif /* HAL_CRYP_MODULE_ENABLED */
-
-#ifdef HAL_DMA2D_MODULE_ENABLED
-#include "stm32f4xx_hal_dma2d.h"
-#endif /* HAL_DMA2D_MODULE_ENABLED */
-
-#ifdef HAL_DAC_MODULE_ENABLED
-#include "stm32f4xx_hal_dac.h"
-#endif /* HAL_DAC_MODULE_ENABLED */
-
-#ifdef HAL_DCMI_MODULE_ENABLED
-#include "stm32f4xx_hal_dcmi.h"
-#endif /* HAL_DCMI_MODULE_ENABLED */
-
-#ifdef HAL_ETH_MODULE_ENABLED
-#include "stm32f4xx_hal_eth.h"
-#endif /* HAL_ETH_MODULE_ENABLED */
-
-#ifdef HAL_FLASH_MODULE_ENABLED
-#include "stm32f4xx_hal_flash.h"
-#endif /* HAL_FLASH_MODULE_ENABLED */
-
-#ifdef HAL_SRAM_MODULE_ENABLED
-#include "stm32f4xx_hal_sram.h"
-#endif /* HAL_SRAM_MODULE_ENABLED */
-
-#ifdef HAL_NOR_MODULE_ENABLED
-#include "stm32f4xx_hal_nor.h"
-#endif /* HAL_NOR_MODULE_ENABLED */
-
-#ifdef HAL_NAND_MODULE_ENABLED
-#include "stm32f4xx_hal_nand.h"
-#endif /* HAL_NAND_MODULE_ENABLED */
-
-#ifdef HAL_PCCARD_MODULE_ENABLED
-#include "stm32f4xx_hal_pccard.h"
-#endif /* HAL_PCCARD_MODULE_ENABLED */
-
-#ifdef HAL_SDRAM_MODULE_ENABLED
-#include "stm32f4xx_hal_sdram.h"
-#endif /* HAL_SDRAM_MODULE_ENABLED */
-
-#ifdef HAL_HASH_MODULE_ENABLED
-#include "stm32f4xx_hal_hash.h"
-#endif /* HAL_HASH_MODULE_ENABLED */
-
-#ifdef HAL_I2C_MODULE_ENABLED
-#include "stm32f4xx_hal_i2c.h"
-#endif /* HAL_I2C_MODULE_ENABLED */
-
-#ifdef HAL_SMBUS_MODULE_ENABLED
-#include "stm32f4xx_hal_smbus.h"
-#endif /* HAL_SMBUS_MODULE_ENABLED */
-
-#ifdef HAL_I2S_MODULE_ENABLED
-#include "stm32f4xx_hal_i2s.h"
-#endif /* HAL_I2S_MODULE_ENABLED */
-
-#ifdef HAL_IWDG_MODULE_ENABLED
-#include "stm32f4xx_hal_iwdg.h"
-#endif /* HAL_IWDG_MODULE_ENABLED */
-
-#ifdef HAL_LTDC_MODULE_ENABLED
-#include "stm32f4xx_hal_ltdc.h"
-#endif /* HAL_LTDC_MODULE_ENABLED */
-
-#ifdef HAL_PWR_MODULE_ENABLED
-#include "stm32f4xx_hal_pwr.h"
-#endif /* HAL_PWR_MODULE_ENABLED */
-
-#ifdef HAL_RNG_MODULE_ENABLED
-#include "stm32f4xx_hal_rng.h"
-#endif /* HAL_RNG_MODULE_ENABLED */
-
-#ifdef HAL_RTC_MODULE_ENABLED
-#include "stm32f4xx_hal_rtc.h"
-#endif /* HAL_RTC_MODULE_ENABLED */
-
-#ifdef HAL_SAI_MODULE_ENABLED
-#include "stm32f4xx_hal_sai.h"
-#endif /* HAL_SAI_MODULE_ENABLED */
-
-#ifdef HAL_SD_MODULE_ENABLED
-#include "stm32f4xx_hal_sd.h"
-#endif /* HAL_SD_MODULE_ENABLED */
-
-#ifdef HAL_SPI_MODULE_ENABLED
-#include "stm32f4xx_hal_spi.h"
-#endif /* HAL_SPI_MODULE_ENABLED */
-
-#ifdef HAL_TIM_MODULE_ENABLED
-#include "stm32f4xx_hal_tim.h"
-#endif /* HAL_TIM_MODULE_ENABLED */
-
-#ifdef HAL_UART_MODULE_ENABLED
-#include "stm32f4xx_hal_uart.h"
-#endif /* HAL_UART_MODULE_ENABLED */
-
-#ifdef HAL_USART_MODULE_ENABLED
-#include "stm32f4xx_hal_usart.h"
-#endif /* HAL_USART_MODULE_ENABLED */
-
-#ifdef HAL_IRDA_MODULE_ENABLED
-#include "stm32f4xx_hal_irda.h"
-#endif /* HAL_IRDA_MODULE_ENABLED */
-
-#ifdef HAL_SMARTCARD_MODULE_ENABLED
-#include "stm32f4xx_hal_smartcard.h"
-#endif /* HAL_SMARTCARD_MODULE_ENABLED */
-
-#ifdef HAL_WWDG_MODULE_ENABLED
-#include "stm32f4xx_hal_wwdg.h"
-#endif /* HAL_WWDG_MODULE_ENABLED */
-
-#ifdef HAL_PCD_MODULE_ENABLED
-#include "stm32f4xx_hal_pcd.h"
-#endif /* HAL_PCD_MODULE_ENABLED */
-
-#ifdef HAL_HCD_MODULE_ENABLED
-#include "stm32f4xx_hal_hcd.h"
-#endif /* HAL_HCD_MODULE_ENABLED */
-
-#ifdef HAL_DSI_MODULE_ENABLED
-#include "stm32f4xx_hal_dsi.h"
-#endif /* HAL_DSI_MODULE_ENABLED */
-
-#ifdef HAL_QSPI_MODULE_ENABLED
-#include "stm32f4xx_hal_qspi.h"
-#endif /* HAL_QSPI_MODULE_ENABLED */
-
-#ifdef HAL_CEC_MODULE_ENABLED
-#include "stm32f4xx_hal_cec.h"
-#endif /* HAL_CEC_MODULE_ENABLED */
-
-#ifdef HAL_FMPI2C_MODULE_ENABLED
-#include "stm32f4xx_hal_fmpi2c.h"
-#endif /* HAL_FMPI2C_MODULE_ENABLED */
-
-#ifdef HAL_SPDIFRX_MODULE_ENABLED
-#include "stm32f4xx_hal_spdifrx.h"
-#endif /* HAL_SPDIFRX_MODULE_ENABLED */
-
-#ifdef HAL_DFSDM_MODULE_ENABLED
-#include "stm32f4xx_hal_dfsdm.h"
-#endif /* HAL_DFSDM_MODULE_ENABLED */
-
-#ifdef HAL_LPTIM_MODULE_ENABLED
-#include "stm32f4xx_hal_lptim.h"
-#endif /* HAL_LPTIM_MODULE_ENABLED */
-
-#ifdef HAL_MMC_MODULE_ENABLED
-#include "stm32f4xx_hal_mmc.h"
-#endif /* HAL_MMC_MODULE_ENABLED */
-
-/* Exported macro ------------------------------------------------------------*/
-#ifdef USE_FULL_ASSERT
- /**
-  * @brief  The assert_param macro is used for function's parameters check.
-  * @param  expr: If expr is false, it calls assert_failed function
-  *         which reports the name of the source file and the source
-  *         line number of the call that failed.
-  *         If expr is true, it returns no value.
-  * @retval None
-  */
-#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
-/* Exported functions ------------------------------------------------------- */
-void assert_failed(uint8_t *file, uint32_t line);
-#else
-#define assert_param(expr) ((void)0U)
-#endif /* USE_FULL_ASSERT */
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __STM32F4xx_HAL_CONF_H */
-
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.cpp

@@ -28,7 +28,7 @@
  *******************************************************************************
  */
 
-#include "variant.h"
+#include "pins_arduino.h"
 
 #ifdef __cplusplus
 extern "C" {

buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.h

@@ -29,11 +29,6 @@
  */
 #pragma once
 
-/*----------------------------------------------------------------------------
- *        Headers
- *----------------------------------------------------------------------------*/
-#include <PeripheralPins.h>
-
 #ifdef __cplusplus
 extern "C" {
 #endif // __cplusplus
@@ -41,7 +36,6 @@ extern "C" {
 /*----------------------------------------------------------------------------
  *        Pins
  *----------------------------------------------------------------------------*/
-extern const PinName digitalPin[];
 
 #ifdef STM32F405RX
   #define STM32F4X_PIN_NUM  64  //64 pins mcu, 51 gpio
@@ -214,6 +208,10 @@ extern const PinName digitalPin[];
   #define PI7   (115+STM32F4X_ADC_NUM) //1:TIM8_CH3
 #endif
 
+#ifdef HAL_GPIO_MODULE_ENABLED
+#error foo
+#endif
+
 
 // This must be a literal
 #define NUM_DIGITAL_PINS        (STM32F4X_GPIO_NUM)
@@ -266,6 +264,9 @@ extern const PinName digitalPin[];
 #define PIN_SERIAL_RX           PA10
 #define PIN_SERIAL_TX           PA9
 
+/* Extra HAL modules */
+#define HAL_PCD_MODULE_ENABLED
+
 #ifdef __cplusplus
 } // extern "C"
 #endif

platformio.ini

@@ -479,7 +479,7 @@ monitor_speed = 250000
 # Bigtreetech SKR Pro (STM32F407ZGT6 ARM Cortex-M4)
 #
 [env:BIGTREE_SKR_PRO]
-platform = ststm32@5.4.3
+platform = ststm32
 framework = arduino
 board = BigTree_SKR_Pro
 extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py
@@ -495,7 +495,7 @@ monitor_speed = 250000
 # BIGTREE_SKR_BTT002 (STM32F407VET6 ARM Cortex-M4)
 #
 [env:BIGTREE_BTT002]
-platform = ststm32@5.4.3
+platform = ststm32
 framework = arduino
 board = BigTree_Btt002
 extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py