Bring configurator up-to-date

Marlin/configurator/config/Configuration.h

 //===========================================================================
 //============================= SCARA Printer ===============================
 //===========================================================================
-// For a Delta printer replace the configuration files with the files in the
+// For a Scara printer replace the configuration files with the files in the
 // example_configurations/SCARA directory.
 //
 
 // The following define selects which electronics board you have.
 // Please choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_ULTIMAKER
+  #define MOTHERBOARD BOARD_RAMPS_13_EFB
 #endif
 
 // Define this to set a custom name for your generic Mendel,
 // :[1,2,3,4]
 #define EXTRUDERS 1
 
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+//#define EXTRUDER_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
+
 //// The following define selects which power supply you have. Please choose the one that matches your setup
 // 1 = ATX
 // 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
 // :{1:'ATX',2:'X-Box 360'}
+
 #define POWER_SUPPLY 1
 
 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 //     Use it for Testing or Development purposes. NEVER for production machine.
 //     #define DUMMY_THERMISTOR_998_VALUE 25
 //     #define DUMMY_THERMISTOR_999_VALUE 100
-// :{ 0: "Not used", 4: "10k !! do not use for a hotend. Bad resolution at high temp. !!", 1: "100k / 4.7k - EPCOS", 51: "100k / 1k - EPCOS", 6: "100k / 4.7k EPCOS - Not as accurate as Table 1", 5: "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 7: "100k / 4.7k Honeywell 135-104LAG-J01", 71: "100k / 4.7k Honeywell 135-104LAF-J01", 8: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", 9: "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", 10: "100k / 4.7k RS 198-961", 11: "100k / 4.7k beta 3950 1%", 12: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", 13: "100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", 60: "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", 55: "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 2: "200k / 4.7k - ATC Semitec 204GT-2", 52: "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", 3: "Mendel-parts / 4.7k", 1047: "Pt1000 / 4.7k", 1010: "Pt1000 / 1k (non standard)", 20: "PT100 (Ultimainboard V2.x)", 147: "Pt100 / 4.7k", 110: "Pt100 / 1k (non-standard)", 998: "Dummy 1", 999: "Dummy 2" }
-#define TEMP_SENSOR_0 -1
-#define TEMP_SENSOR_1 -1
+
+#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_BED 0
   // #define ENDSTOPPULLUP_XMIN
   // #define ENDSTOPPULLUP_YMIN
   // #define ENDSTOPPULLUP_ZMIN
+  // #define ENDSTOPPULLUP_ZPROBE
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 //#define DISABLE_MAX_ENDSTOPS
 //#define DISABLE_MIN_ENDSTOPS
 
 // @section machine
+// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
+// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
+// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
+// this has no effect.
+//#define DISABLE_Z_PROBE_ENDSTOP
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR true
+#define INVERT_X_DIR false
 #define INVERT_Y_DIR false
-#define INVERT_Z_DIR true
+#define INVERT_Z_DIR false
 
 // @section extruder
 
 #define X_MIN_POS 0
 #define Y_MIN_POS 0
 #define Z_MIN_POS 0
-#define X_MAX_POS 205
-#define Y_MAX_POS 205
+#define X_MAX_POS 200
+#define Y_MAX_POS 200
 #define Z_MAX_POS 200
 
 //===========================================================================
 
 // default settings
 
-#define DEFAULT_AXIS_STEPS_PER_UNIT   {78.7402,78.7402,200.0*8/3,760*1.1}  // default steps per unit for Ultimaker
-#define DEFAULT_MAX_FEEDRATE          {500, 500, 5, 25}    // (mm/sec)
-#define DEFAULT_MAX_ACCELERATION      {9000,9000,100,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
-
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000   // X, Y, Z and E max acceleration in mm/s^2 for retracts
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {80,80,4000,500}  // default steps per unit for Ultimaker
+#define DEFAULT_MAX_FEEDRATE          {300, 300, 5, 25}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {3000,3000,100,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
 
-// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
-// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
-// For the other hotends it is their distance from the extruder 0 hotend.
-// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
-// #define EXTRUDER_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
+#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  3000   // E acceleration in mm/s^2 for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
 
 // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
 #define DEFAULT_XYJERK                20.0    // (mm/sec)
 // Preheat Constants
 #define PLA_PREHEAT_HOTEND_TEMP 180
 #define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
 
 #define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define ABS_PREHEAT_HPB_TEMP 110
+#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
 
 //==============================LCD and SD support=============================
 // @section lcd
 // Define your display language below. Replace (en) with your language code and uncomment.
 // en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
-//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
+#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
 // Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
 // To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
 // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
 // #define PHOTOGRAPH_PIN     23
 
-// SF send wrong arc g-codes when using Arc Point as fillet procedure
+// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
 //#define SF_ARC_FIX
 
 // Support for the BariCUDA Paste Extruder.
 #define MAX_MEASUREMENT_DELAY			20  //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
 
 //defines used in the code
-#define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially 
+#define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially
 
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY

Marlin/configurator/config/Configuration_adv.h

 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2
-#define HOMING_BUMP_DIVISOR {10, 10, 20}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
+#define HOMING_BUMP_DIVISOR {2, 2, 4}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 // @section machine
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1

Marlin/configurator/config/boards.h

 #define BOARD_CHEAPTRONIC       2    // Cheaptronic v1.0
 #define BOARD_SETHI             20   // Sethi 3D_1
 #define BOARD_RAMPS_OLD         3    // MEGA/RAMPS up to 1.2
-#define BOARD_RAMPS_13_EFB      33   // RAMPS 1.3 / 1.4 (Extruder, Fan, Bed)
-#define BOARD_RAMPS_13_EEB      34   // RAMPS 1.3 / 1.4 (Extruder0, Extruder1, Bed)
-#define BOARD_RAMPS_13_EFF      35   // RAMPS 1.3 / 1.4 (Extruder, Fan, Fan)
-#define BOARD_RAMPS_13_EEF      36   // RAMPS 1.3 / 1.4 (Extruder0, Extruder1, Fan)
+#define BOARD_RAMPS_13_EFB      33   // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
+#define BOARD_RAMPS_13_EEB      34   // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
+#define BOARD_RAMPS_13_EFF      35   // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
+#define BOARD_RAMPS_13_EEF      36   // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
+#define BOARD_FELIX2            37   // Felix 2.0+ Electronics Board (RAMPS like)
 #define BOARD_DUEMILANOVE_328P  4    // Duemilanove w/ ATMega328P pin assignments
 #define BOARD_GEN6              5    // Gen6
 #define BOARD_GEN6_DELUXE       51   // Gen6 deluxe
 #define BOARD_ULTIMAKER         7    // Ultimaker
 #define BOARD_ULTIMAKER_OLD     71   // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
 #define BOARD_ULTIMAIN_2        72   // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
-#define BOARD_3DRAG             77   // 3Drag
-#define BOARD_K8200             78   // Vellemann K8200 (derived from 3Drag)
+#define BOARD_3DRAG             77   // 3Drag Controller
+#define BOARD_K8200             78   // Vellemann K8200 Controller (derived from 3Drag Controller)
 #define BOARD_TEENSYLU          8    // Teensylu
 #define BOARD_RUMBA             80   // Rumba
 #define BOARD_PRINTRBOARD       81   // Printrboard (AT90USB1286)
 #define BOARD_BRAINWAVE         82   // Brainwave (AT90USB646)
 #define BOARD_SAV_MKI           83   // SAV Mk-I (AT90USB1286)
 #define BOARD_TEENSY2           84   // Teensy++2.0 (AT90USB1286) - CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84  make
+#define BOARD_BRAINWAVE_PRO     85   // Brainwave Pro (AT90USB1286)
 #define BOARD_GEN3_PLUS         9    // Gen3+
 #define BOARD_GEN3_MONOLITHIC   22   // Gen3 Monolithic Electronics
 #define BOARD_MEGATRONICS       70   // Megatronics
 #define BOARD_LEAPFROG          999  // Leapfrog
 #define BOARD_WITBOX            41   // bq WITBOX
 #define BOARD_HEPHESTOS         42   // bq Prusa i3 Hephestos
+#define BOARD_BAM_DICE          401  // 2PrintBeta BAM&DICE with STK drivers
+#define BOARD_BAM_DICE_DUE      402  // 2PrintBeta BAM&DICE Due with STK drivers
 
 #define BOARD_99                99   // This is in pins.h but...?
 
 #define MB(board) (MOTHERBOARD==BOARD_##board)
-#define IS_RAMPS (MB(RAMPS_OLD) || MB(RAMPS_13_EFB) || MB(RAMPS_13_EEB) || MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF))
 
 #endif //__BOARDS_H

Marlin/configurator/config/language.h

 //
 //   ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h"
 //   ==> ALSO TRY ALL AVAILABLE LANGUAGE OPTIONS
+// See also documentation/LCDLanguageFont.md
 
 // Languages
-// en    English
-// pl    Polish
-// fr    French
-// de    German
-// es    Spanish
-// ru    Russian
-// it    Italian
-// pt    Portuguese
-// pt-br Portuguese (Brazil)
-// fi    Finnish
-// an    Aragonese
-// nl    Dutch
-// ca    Catalan
-// eu    Basque-Euskera
+// en       English
+// pl       Polish
+// fr       French
+// de       German
+// es       Spanish
+// ru       Russian
+// it       Italian
+// pt       Portuguese
+// pt-br    Portuguese (Brazil)
+// fi       Finnish
+// an       Aragonese
+// nl       Dutch
+// ca       Catalan
+// eu       Basque-Euskera
+// kana     Japanese
+// kana_utf Japanese
 
 #ifndef LANGUAGE_INCLUDE
   // pick your language from the list above
   #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 #endif
 
+#ifdef HAS_AUTOMATIC_VERSIONING
+  #include "_Version.h"
+#endif
+
 #define PROTOCOL_VERSION "1.0"
 
 #if MB(ULTIMAKER)|| MB(ULTIMAKER_OLD)|| MB(ULTIMAIN_2)
 #elif MB(HEPHESTOS)
   #define MACHINE_NAME "HEPHESTOS"
   #define FIRMWARE_URL "http://www.bq.com/gb/downloads-prusa-i3-hephestos.html"
-#else // Default firmware set to Mendel
-  #define MACHINE_NAME "Mendel"
-  #define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin"
+#elif MB(BRAINWAVE_PRO)
+  #define MACHINE_NAME "Kossel Pro"
+  #ifndef FIRMWARE_URL
+    #define FIRMWARE_URL "https://github.com/OpenBeamUSA/Marlin/"
+  #endif
+#else
+  #ifndef MACHINE_NAME
+    #define MACHINE_NAME "Mendel"
+  #endif
 #endif
 
 #ifdef CUSTOM_MENDEL_NAME
+  #warning CUSTOM_MENDEL_NAME deprecated - use CUSTOM_MACHINE_NAME
+  #define CUSTOM_MACHINE_NAME CUSTOM_MENDEL_NAME
+#endif
+
+#ifdef CUSTOM_MACHINE_NAME
   #undef MACHINE_NAME
-  #define MACHINE_NAME CUSTOM_MENDEL_NAME
+  #define MACHINE_NAME CUSTOM_MACHINE_NAME
+#endif
+
+#ifndef FIRMWARE_URL
+  #define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin"
+#endif
+
+#ifndef BUILD_VERSION
+  #define BUILD_VERSION "V1; Sprinter/grbl mashup for gen6"
 #endif
 
 #ifndef MACHINE_UUID
-  #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+   #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 #endif
 
 
 #define MSG_HEATING_COMPLETE                "Heating done."
 #define MSG_BED_HEATING                     "Bed Heating."
 #define MSG_BED_DONE                        "Bed done."
-#define MSG_M115_REPORT                     "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n"
+#define MSG_M115_REPORT                     "FIRMWARE_NAME:Marlin " BUILD_VERSION " FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n"
 #define MSG_COUNT_X                         " Count X: "
 #define MSG_ERR_KILLED                      "Printer halted. kill() called!"
 #define MSG_ERR_STOPPED                     "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
 #define MSG_UNKNOWN_COMMAND                 "Unknown command: \""
 #define MSG_ACTIVE_EXTRUDER                 "Active Extruder: "
 #define MSG_INVALID_EXTRUDER                "Invalid extruder"
+#define MSG_INVALID_SOLENOID                "Invalid solenoid"
 #define MSG_X_MIN                           "x_min: "
 #define MSG_X_MAX                           "x_max: "
 #define MSG_Y_MIN                           "y_min: "
 #define MSG_Y_MAX                           "y_max: "
 #define MSG_Z_MIN                           "z_min: "
 #define MSG_Z_MAX                           "z_max: "
+#define MSG_Z2_MAX                          "z2_max: "
+#define MSG_Z_PROBE                         "z_probe: "
 #define MSG_M119_REPORT                     "Reporting endstop status"
 #define MSG_ENDSTOP_HIT                     "TRIGGERED"
 #define MSG_ENDSTOP_OPEN                    "open"
 
 #define MSG_ERR_EEPROM_WRITE                "Error writing to EEPROM!"
 
+// temperature.cpp strings
+#define MSG_PID_AUTOTUNE                    "PID Autotune"
+#define MSG_PID_AUTOTUNE_START              MSG_PID_AUTOTUNE " start"
+#define MSG_PID_AUTOTUNE_FAILED             MSG_PID_AUTOTUNE " failed!"
+#define MSG_PID_BAD_EXTRUDER_NUM            MSG_PID_AUTOTUNE_FAILED " Bad extruder number"
+#define MSG_PID_TEMP_TOO_HIGH               MSG_PID_AUTOTUNE_FAILED " Temperature too high"
+#define MSG_PID_TIMEOUT                     MSG_PID_AUTOTUNE_FAILED " timeout"
+#define MSG_BIAS                            " bias: "
+#define MSG_D                               " d: "
+#define MSG_T_MIN                           " min: "
+#define MSG_T_MAX                           " max: "
+#define MSG_KU                              " Ku: "
+#define MSG_TU                              " Tu: "
+#define MSG_CLASSIC_PID                     " Classic PID "
+#define MSG_KP                              " Kp: "
+#define MSG_KI                              " Ki: "
+#define MSG_KD                              " Kd: "
+#define MSG_OK_B                            "ok B:"
+#define MSG_OK_T                            "ok T:"
+#define MSG_AT                              " @:"
+#define MSG_PID_AUTOTUNE_FINISHED           MSG_PID_AUTOTUNE " finished! Put the last Kp, Ki and Kd constants from above into Configuration.h"
+#define MSG_PID_DEBUG                       " PID_DEBUG "
+#define MSG_PID_DEBUG_INPUT                 ": Input "
+#define MSG_PID_DEBUG_OUTPUT                " Output "
+#define MSG_PID_DEBUG_PTERM                 " pTerm "
+#define MSG_PID_DEBUG_ITERM                 " iTerm "
+#define MSG_PID_DEBUG_DTERM                 " dTerm "
+#define MSG_HEATING_FAILED                  "Heating failed"
+#define MSG_EXTRUDER_SWITCHED_OFF           "Extruder switched off. Temperature difference between temp sensors is too high !"
+
+#define MSG_INVALID_EXTRUDER_NUM            " - Invalid extruder number !"
+#define MSG_THERMAL_RUNAWAY_STOP            "Thermal Runaway, system stopped! Heater_ID: "
+#define MSG_SWITCHED_OFF_MAX                " switched off. MAXTEMP triggered !!"
+#define MSG_MINTEMP_EXTRUDER_OFF            ": Extruder switched off. MINTEMP triggered !"
+#define MSG_MAXTEMP_EXTRUDER_OFF            ": Extruder" MSG_SWITCHED_OFF_MAX
+#define MSG_MAXTEMP_BED_OFF                 "Heated bed" MSG_SWITCHED_OFF_MAX
+
 // LCD Menu Messages
 
-// Add your own character. Reference: https://github.com/MarlinFirmware/Marlin/pull/1434 photos
-//                                and https://www.sparkfun.com/datasheets/LCD/HD44780.pdf page 17-18
-#ifdef DOGLCD
-  #define STR_Ae "\304"               // 'Ä' U8glib
-  #define STR_ae "\344"               // 'ä'
-  #define STR_Oe "\326"               // 'Ö'
-  #define STR_oe STR_Oe               // 'ö'
-  #define STR_Ue "\334"               // 'Ü'
-  #define STR_ue STR_Ue               // 'ü'
-  #define STR_sz "\337"               // 'ß'
-  #define STR_h2 "\262"               // '²'
-  #define STR_h3 "\263"               // '³'
-  #define STR_Deg "\260"              // '°'
-  #define STR_THERMOMETER "\377"
-#else
-  #ifdef DISPLAY_CHARSET_HD44780_JAPAN // HD44780 ROM Code: A00 (Japan)
-    #define STR_ae "\xe1"
-    #define STR_Ae STR_ae
-    #define STR_oe "\357"
-    #define STR_Oe STR_oe
-    #define STR_ue "\365"
-    #define STR_Ue STR_ue
-    #define STR_sz "\342"
-    #define STR_h2 "2"
-    #define STR_h3 "3"
-    #define STR_Deg "\271"
-    #define STR_THERMOMETER "\002"
-  #endif
-  #ifdef DISPLAY_CHARSET_HD44780_WESTERN // HD44780 ROM Code: A02 (Western)
-    #define STR_Ae "\216"
-    #define STR_ae "\204"
-    #define STR_Oe "\211"
-    #define STR_oe "\204"
-    #define STR_Ue "\212"
-    #define STR_ue "\201"
-    #define STR_sz "\160"
-    #define STR_h2 "\262"
-    #define STR_h3 "\263"
-    #define STR_Deg "\337"
-    #define STR_THERMOMETER "\002"
-  #endif
+#if !(defined( DISPLAY_CHARSET_HD44780_JAPAN ) || defined( DISPLAY_CHARSET_HD44780_WESTERN ) || defined( DISPLAY_CHARSET_HD44780_CYRILLIC ))
+  #define DISPLAY_CHARSET_HD44780_JAPAN
 #endif
-/*
-#define TESTSTRING000 "\000\001\002\003\004\005\006\007\010\011\012\013\014\015\016\017"
-#define TESTSTRING020 "\020\021\022\023\024\025\026\027\030\031\032\033\034\035\036\037"
-#define TESTSTRING040 "\040\041\042\043\044\045\046\047\050\051\052\053\054\055\056\057"
-#define TESTSTRING060 "\060\061\062\063\064\065\066\067\070\071\072\073\074\075\076\077"
-#define TESTSTRING100 "\100\101\102\103\104\105\106\107\110\111\112\113\114\115\116\117"
-#define TESTSTRING120 "\120\121\122\123\124\125\126\127\130\131\132\133\134\135\136\137"
-#define TESTSTRING140 "\140\141\142\143\144\145\146\147\150\151\152\153\154\155\156\157"
-#define TESTSTRING160 "\160\161\162\163\164\165\166\167\170\171\172\173\174\175\176\177"
-#define TESTSTRING200 "\200\201\202\203\204\205\206\207\210\211\212\213\214\215\216\217"
-#define TESTSTRING220 "\220\221\222\223\224\225\226\227\230\231\232\233\234\235\236\237"
-#define TESTSTRING240 "\240\241\242\243\244\245\246\247\250\251\252\253\254\255\256\257"
-#define TESTSTRING260 "\260\261\262\263\264\265\266\267\270\271\272\273\274\275\276\277"
-#define TESTSTRING300 "\300\301\302\303\304\305\306\307\310\311\312\313\314\315\316\317"
-#define TESTSTRING320 "\320\321\322\323\324\325\326\327\330\331\332\333\334\335\336\337"
-#define TESTSTRING340 "\340\341\342\343\344\345\346\347\350\351\352\353\354\355\356\357"
-#define TESTSTRING360 "\360\361\362\363\364\365\366\367\370\371\372\373\374\375\376\377"
-*/
 
 #include LANGUAGE_INCLUDE
 #include "language_en.h"