Remove PID examples from preconfigured configs

Marlin/configurator/config/Configuration.h

@@ -205,21 +205,22 @@ Here are some standard links for getting your machine calibrated:
   #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
 
-// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-// Ultimaker
-    #define  DEFAULT_Kp 22.2
-    #define  DEFAULT_Ki 1.08
-    #define  DEFAULT_Kd 114
-
-// MakerGear
-//    #define  DEFAULT_Kp 7.0
-//    #define  DEFAULT_Ki 0.1
-//    #define  DEFAULT_Kd 12
-
-// Mendel Parts V9 on 12V
-//    #define  DEFAULT_Kp 63.0
-//    #define  DEFAULT_Ki 2.25
-//    #define  DEFAULT_Kd 440
+  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+  // Ultimaker
+  #define  DEFAULT_Kp 22.2
+  #define  DEFAULT_Ki 1.08
+  #define  DEFAULT_Kd 114
+
+  // MakerGear
+  //#define  DEFAULT_Kp 7.0
+  //#define  DEFAULT_Ki 0.1
+  //#define  DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  //#define  DEFAULT_Kp 63.0
+  //#define  DEFAULT_Ki 2.25
+  //#define  DEFAULT_Kd 440
+
 #endif // PIDTEMP
 
 //===========================================================================

Marlin/example_configurations/Hephestos/Configuration.h

@@ -208,23 +208,7 @@ Here are some standard links for getting your machine calibrated:
   #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
 
-  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-  // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
-
-  // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
-
-  // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
-
-  // Hephestos (i3)
+  // Hephestos i3
   #define  DEFAULT_Kp 23.05
   #define  DEFAULT_Ki 2.00
   #define  DEFAULT_Kd 66.47

Marlin/example_configurations/K8200/Configuration.h

@@ -210,22 +210,6 @@ Here are some standard links for getting your machine calibrated:
   #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
 
-  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-  // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
-
-  // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
-
-  // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
-
   // Vellemann K8200 Extruder - calculated with PID Autotune and tested
   #define  DEFAULT_Kp 24.29
   #define  DEFAULT_Ki 1.58
@@ -261,18 +245,6 @@ Here are some standard links for getting your machine calibrated:
 
   #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
 
-  //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
-
-  //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
-
   //Vellemann K8200 PCB heatbed with standard PCU at 60 degreesC - calculated with PID Autotune and tested
   //from pidautotune
   #define  DEFAULT_bedKp 341.88

Marlin/example_configurations/RigidBot/Configuration.h

@@ -211,16 +211,6 @@ Here are some standard links for getting your machine calibrated:
   #define  DEFAULT_Ki 4.21      //Base DGlass3D/E3Dv6 = 0.85 ; RigidBot redesigned = 0.85
   #define  DEFAULT_Kd 88.41     //Base DGlass3D/E3Dv6 = 245  ; RigidBot redesigned = 76.55
 
-  // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
-
-  // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
-
 #endif // PIDTEMP
 
 //===========================================================================
@@ -256,12 +246,6 @@ Here are some standard links for getting your machine calibrated:
   #define  DEFAULT_bedKi 66.5
   #define  DEFAULT_bedKd 480
 
-  //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
-
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
 

Marlin/example_configurations/SCARA/Configuration.h

@@ -230,27 +230,6 @@ Here are some standard links for getting your machine calibrated:
   #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
 
-  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-  // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
-
-  // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
-
-  // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
-  
-  // Jhead MK5: From Autotune
-  //#define  DEFAULT_Kp 20.92
-  //#define  DEFAULT_Ki 1.51
-  //#define  DEFAULT_Kd 72.34
-    
   // Merlin Hotend: From Autotune
   #define  DEFAULT_Kp 24.5
   #define  DEFAULT_Ki 1.72
@@ -286,18 +265,6 @@ Here are some standard links for getting your machine calibrated:
 
   #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
 
-  //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
-
-  //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
-
   //12v Heatbed Mk3 12V in parallel
   //from pidautotune
   #define  DEFAULT_bedKp 630.14

Marlin/example_configurations/WITBOX/Configuration.h

@@ -208,22 +208,6 @@ Here are some standard links for getting your machine calibrated:
   #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
 
-  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-  // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
-
-  // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
-
-  // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
-
   // Witbox
   #define  DEFAULT_Kp 22.2
   #define  DEFAULT_Ki 1.08

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -205,21 +205,22 @@ Here are some standard links for getting your machine calibrated:
   #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
 
-// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-// Ultimaker
-    #define  DEFAULT_Kp 22.2
-    #define  DEFAULT_Ki 1.08
-    #define  DEFAULT_Kd 114
-
-// MakerGear
-//    #define  DEFAULT_Kp 7.0
-//    #define  DEFAULT_Ki 0.1
-//    #define  DEFAULT_Kd 12
-
-// Mendel Parts V9 on 12V
-//    #define  DEFAULT_Kp 63.0
-//    #define  DEFAULT_Ki 2.25
-//    #define  DEFAULT_Kd 440
+  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+  // Ultimaker
+  #define  DEFAULT_Kp 22.2
+  #define  DEFAULT_Ki 1.08
+  #define  DEFAULT_Kd 114
+
+  // MakerGear
+  //#define  DEFAULT_Kp 7.0
+  //#define  DEFAULT_Ki 0.1
+  //#define  DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  //#define  DEFAULT_Kp 63.0
+  //#define  DEFAULT_Ki 2.25
+  //#define  DEFAULT_Kd 440
+
 #endif // PIDTEMP
 
 //===========================================================================

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -209,27 +209,11 @@ Here are some standard links for getting your machine calibrated:
   #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
 
-  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-  // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
-
   // Kossel Pro
   #define  DEFAULT_Kp 19.30
   #define  DEFAULT_Ki 3.51
   #define  DEFAULT_Kd 26.56
 
-  // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
-
-  // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
-
 #endif // PIDTEMP
 
 //===========================================================================
@@ -266,18 +250,6 @@ Here are some standard links for getting your machine calibrated:
   #define  DEFAULT_bedKi 62.77
   #define  DEFAULT_bedKd 545.98
 
-  //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  //#define  DEFAULT_bedKp 10.00
-  //#define  DEFAULT_bedKi .023
-  //#define  DEFAULT_bedKd 305.4
-
-  //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  //from pidautotune
-  //#define  DEFAULT_bedKp 97.1
-  //#define  DEFAULT_bedKi 1.41
-  //#define  DEFAULT_bedKd 1675.16
-
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
 

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -211,21 +211,6 @@ Here are some standard links for getting your machine calibrated:
   #define  DEFAULT_Ki 2.30
   #define  DEFAULT_Kd 68.15
 
-  // Ultimaker
-  //#define  DEFAULT_Kp 22.2
-  //#define  DEFAULT_Ki 1.08
-  //#define  DEFAULT_Kd 114
-
-  // MakerGear
-  //#define  DEFAULT_Kp 7.0
-  //#define  DEFAULT_Ki 0.1
-  //#define  DEFAULT_Kd 12
-
-  // Mendel Parts V9 on 12V
-  //#define  DEFAULT_Kp 63.0
-  //#define  DEFAULT_Ki 2.25
-  //#define  DEFAULT_Kd 440
-
 #endif // PIDTEMP
 
 //===========================================================================