Updated PR to streamline integration

Marlin/boards.h

@@ -14,6 +14,7 @@
 #define BOARD_RAMPS_13_EEB      34   // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
 #define BOARD_RAMPS_13_EFF      35   // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
 #define BOARD_RAMPS_13_EEF      36   // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
+#define BOARD_FELIX2            37   // Felix 2.0+ Electronics Board (RAMPS like)
 #define BOARD_DUEMILANOVE_328P  4    // Duemilanove w/ ATMega328P pin assignments
 #define BOARD_GEN6              5    // Gen6
 #define BOARD_GEN6_DELUXE       51   // Gen6 deluxe
@@ -52,11 +53,9 @@
 #define BOARD_HEPHESTOS         42   // bq Prusa i3 Hephestos
 #define BOARD_BAM_DICE          401  // 2PrintBeta BAM&DICE with STK drivers
 #define BOARD_BAM_DICE_DUE      402  // 2PrintBeta BAM&DICE Due with STK drivers
-#define BOARD_FELIX2			101  // Felix 2.0+ Electronics
 
 #define BOARD_99                99   // This is in pins.h but...?
 
 #define MB(board) (MOTHERBOARD==BOARD_##board)
 
 #endif //__BOARDS_H
-

Marlin/example_configurations/Felix/Configuration.h

@@ -0,0 +1,853 @@
+#ifndef CONFIGURATION_H
+#define CONFIGURATION_H
+
+#include "boards.h"
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
+// This configuration file contains the basic settings.
+// Advanced settings can be found in Configuration_adv.h
+// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
+
+//===========================================================================
+//============================= DELTA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/delta directory.
+//
+
+//===========================================================================
+//============================= SCARA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/SCARA directory.
+//
+
+// User-specified version info of this build to display in [Pronterface, etc] terminal window during
+// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
+// build by the user have been successfully uploaded into firmware.
+#define STRING_VERSION "1.0.2"
+#define STRING_URL "reprap.org"
+#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time
+#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+#define STRING_SPLASH_LINE1 "v" STRING_VERSION // will be shown during bootup in line 1
+//#define STRING_SPLASH_LINE2 STRING_VERSION_CONFIG_H // will be shown during bootup in line2
+
+// SERIAL_PORT selects which serial port should be used for communication with the host.
+// This allows the connection of wireless adapters (for instance) to non-default port pins.
+// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
+#define SERIAL_PORT 0
+
+// This determines the communication speed of the printer
+#define BAUDRATE 250000
+
+// This enables the serial port associated to the Bluetooth interface
+//#define BTENABLED              // Enable BT interface on AT90USB devices
+
+// The following define selects which electronics board you have.
+// Please choose the name from boards.h that matches your setup
+#ifndef MOTHERBOARD
+  #define MOTHERBOARD BOARD_FELIX2
+#endif
+
+// Define this to set a custom name for your generic Mendel,
+// #define CUSTOM_MENDEL_NAME "This Mendel"
+
+// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
+// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
+// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+
+// This defines the number of extruders
+#define EXTRUDERS 2
+
+//// The following define selects which power supply you have. Please choose the one that matches your setup
+// 1 = ATX
+// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
+
+#define POWER_SUPPLY 1
+
+// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
+#define PS_DEFAULT_OFF
+
+//===========================================================================
+//============================= Thermal Settings ============================
+//===========================================================================
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 110 is Pt100 with 1k pullup (non standard)
+// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
+//     Use it for Testing or Development purposes. NEVER for production machine.
+//     #define DUMMY_THERMISTOR_998_VALUE 25
+//     #define DUMMY_THERMISTOR_999_VALUE 100
+
+#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_1 1
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_3 0
+#define TEMP_SENSOR_BED 1
+
+// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
+//#define TEMP_SENSOR_1_AS_REDUNDANT
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
+
+// Actual temperature must be close to target for this long before M109 returns success
+#define TEMP_RESIDENCY_TIME 15  // (seconds)
+#define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// The minimal temperature defines the temperature below which the heater will not be enabled It is used
+// to check that the wiring to the thermistor is not broken.
+// Otherwise this would lead to the heater being powered on all the time.
+#define HEATER_0_MINTEMP 5
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define HEATER_3_MINTEMP 5
+#define BED_MINTEMP 5
+
+// When temperature exceeds max temp, your heater will be switched off.
+// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
+// You should use MINTEMP for thermistor short/failure protection.
+#define HEATER_0_MAXTEMP 275
+#define HEATER_1_MAXTEMP 275
+#define HEATER_2_MAXTEMP 275
+#define HEATER_3_MAXTEMP 275
+#define BED_MAXTEMP 150
+
+// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
+// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
+// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
+//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
+
+// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
+//#define EXTRUDER_WATTS (12.0*12.0/6.7) //  P=I^2/R
+//#define BED_WATTS (12.0*12.0/1.1)      // P=I^2/R
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
+// Comment the following line to disable PID and enable bang-bang.
+#define PIDTEMP
+#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#ifdef PIDTEMP
+  //#define PID_DEBUG // Sends debug data to the serial port.
+  //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
+  //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
+  //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
+                                    // Set/get with gcode: M301 E[extruder number, 0-2]
+  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+                                  // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+  #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
+  #define K1 0.95 //smoothing factor within the PID
+  #define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
+
+  // Felix 2.0+ electronics with v4 Hotend
+  #define DEFAULT_Kp 12
+  #define DEFAULT_Ki 0.84
+  #define DEFAULT_Kd 85
+
+#endif // PIDTEMP
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+//#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+    #define  DEFAULT_bedKp 10.00
+    #define  DEFAULT_bedKi .023
+    #define  DEFAULT_bedKd 305.4
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+//    #define  DEFAULT_bedKp 97.1
+//    #define  DEFAULT_bedKi 1.41
+//    #define  DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
+//can be software-disabled for whatever purposes by
+#define PREVENT_DANGEROUS_EXTRUDE
+//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
+#define PREVENT_LENGTHY_EXTRUDE
+
+#define EXTRUDE_MINTEMP 170
+#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
+
+//===========================================================================
+//============================= Thermal Runaway Protection ==================
+//===========================================================================
+/*
+This is a feature to protect your printer from burn up in flames if it has
+a thermistor coming off place (this happened to a friend of mine recently and
+motivated me writing this feature).
+
+The issue: If a thermistor come off, it will read a lower temperature than actual.
+The system will turn the heater on forever, burning up the filament and anything
+else around.
+
+After the temperature reaches the target for the first time, this feature will
+start measuring for how long the current temperature stays below the target
+minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
+
+If it stays longer than _PERIOD, it means the thermistor temperature
+cannot catch up with the target, so something *may be* wrong. Then, to be on the
+safe side, the system will he halt.
+
+Bear in mind the count down will just start AFTER the first time the
+thermistor temperature is over the target, so you will have no problem if
+your extruder heater takes 2 minutes to hit the target on heating.
+
+*/
+// If you want to enable this feature for all your extruder heaters,
+// uncomment the 2 defines below:
+
+// Parameters for all extruder heaters
+//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
+
+// If you want to enable this feature for your bed heater,
+// uncomment the 2 defines below:
+
+// Parameters for the bed heater
+//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
+
+
+//===========================================================================
+//============================= Mechanical Settings =========================
+//===========================================================================
+
+// Uncomment the following line to enable CoreXY kinematics
+// #define COREXY
+
+// coarse Endstop Settings
+#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
+
+#ifndef ENDSTOPPULLUPS
+  // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
+  // #define ENDSTOPPULLUP_XMAX
+  // #define ENDSTOPPULLUP_YMAX
+  // #define ENDSTOPPULLUP_ZMAX
+  // #define ENDSTOPPULLUP_XMIN
+  // #define ENDSTOPPULLUP_YMIN
+  // #define ENDSTOPPULLUP_ZMIN
+#endif
+
+#ifdef ENDSTOPPULLUPS
+  #define ENDSTOPPULLUP_XMAX
+  #define ENDSTOPPULLUP_YMAX
+  #define ENDSTOPPULLUP_ZMAX
+  #define ENDSTOPPULLUP_XMIN
+  #define ENDSTOPPULLUP_YMIN
+  #define ENDSTOPPULLUP_ZMIN
+#endif
+
+// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define DISABLE_MAX_ENDSTOPS
+//#define DISABLE_MIN_ENDSTOPS
+
+// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+#define X_ENABLE_ON 0
+#define Y_ENABLE_ON 0
+#define Z_ENABLE_ON 0
+#define E_ENABLE_ON 0 // For all extruders
+
+// Disables axis when it's not being used.
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
+
+#define INVERT_X_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR true    // for Mendel set to true, for Orca set to false
+#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+
+// ENDSTOP SETTINGS:
+// Sets direction of endstops when homing; 1=MAX, -1=MIN
+#define X_HOME_DIR -1
+#define Y_HOME_DIR -1
+#define Z_HOME_DIR -1
+
+#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
+#define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
+
+// Travel limits after homing (units are in mm)
+#define X_MAX_POS 245
+#define X_MIN_POS 0
+#define Y_MAX_POS 205
+#define Y_MIN_POS 0
+#define Z_MAX_POS 235
+#define Z_MIN_POS 0
+
+#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
+#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
+#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+
+//===========================================================================
+//============================= Bed Auto Leveling ===========================
+//===========================================================================
+
+//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
+//#define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#ifdef ENABLE_AUTO_BED_LEVELING
+
+// There are 2 different ways to pick the X and Y locations to probe:
+
+//  - "grid" mode
+//    Probe every point in a rectangular grid
+//    You must specify the rectangle, and the density of sample points
+//    This mode is preferred because there are more measurements.
+//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+
+//  - "3-point" mode
+//    Probe 3 arbitrary points on the bed (that aren't colinear)
+//    You must specify the X & Y coordinates of all 3 points
+
+  #define AUTO_BED_LEVELING_GRID
+  // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
+  // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
+  // and least squares solution is calculated
+  // Note: this feature occupies 10'206 byte
+  #ifdef AUTO_BED_LEVELING_GRID
+
+    // set the rectangle in which to probe
+    #define LEFT_PROBE_BED_POSITION 15
+    #define RIGHT_PROBE_BED_POSITION 170
+    #define BACK_PROBE_BED_POSITION 180
+    #define FRONT_PROBE_BED_POSITION 20
+
+     // set the number of grid points per dimension
+     // I wouldn't see a reason to go above 3 (=9 probing points on the bed)
+    #define AUTO_BED_LEVELING_GRID_POINTS 2
+
+
+  #else  // not AUTO_BED_LEVELING_GRID
+    // with no grid, just probe 3 arbitrary points.  A simple cross-product
+    // is used to esimate the plane of the print bed
+
+      #define ABL_PROBE_PT_1_X 15
+      #define ABL_PROBE_PT_1_Y 180
+      #define ABL_PROBE_PT_2_X 15
+      #define ABL_PROBE_PT_2_Y 20
+      #define ABL_PROBE_PT_3_X 170
+      #define ABL_PROBE_PT_3_Y 20
+
+  #endif // AUTO_BED_LEVELING_GRID
+
+
+  // these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
+  // X and Y offsets must be integers
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29
+  #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
+
+  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
+                                        // Be sure you have this distance over your Z_MAX_POS in case
+
+  #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min
+
+  #define Z_RAISE_BEFORE_PROBING 15    //How much the extruder will be raised before traveling to the first probing point.
+  #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
+
+  //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
+  //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
+  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
+  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
+  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
+
+//  #define PROBE_SERVO_DEACTIVATION_DELAY 300
+
+
+//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
+//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+
+  #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with probe outside the bed area.
+                          // When defined, it will:
+                          // - Allow Z homing only after X and Y homing AND stepper drivers still enabled
+                          // - If stepper drivers timeout, it will need X and Y homing again before Z homing
+                          // - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
+                          // - Block Z homing only when the probe is outside bed area.
+
+  #ifdef Z_SAFE_HOMING
+
+    #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2)    // X point for Z homing when homing all axis (G28)
+    #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2)    // Y point for Z homing when homing all axis (G28)
+
+  #endif
+
+  #ifdef AUTO_BED_LEVELING_GRID	// Check if Probe_Offset * Grid Points is greater than Probing Range
+    #if X_PROBE_OFFSET_FROM_EXTRUDER < 0
+      #if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
+	     #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#else
+      #if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
+	     #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#endif
+    #if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
+      #if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
+	     #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#else
+      #if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
+	     #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+	  #endif
+	#endif
+
+
+  #endif
+
+#endif // ENABLE_AUTO_BED_LEVELING
+
+
+// The position of the homing switches
+//#define MANUAL_HOME_POSITIONS  // If defined, MANUAL_*_HOME_POS below will be used
+//#define BED_CENTER_AT_0_0  // If defined, the center of the bed is at (X=0, Y=0)
+
+//Manual homing switch locations:
+// For deltabots this means top and center of the Cartesian print volume.
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS 0
+#define MANUAL_Z_HOME_POS 0
+//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+
+//// MOVEMENT SETTINGS
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0}  // set the homing speeds (mm/min)
+
+// default settings
+
+// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {76.190476, 76.190476, 1600, 164}
+#define DEFAULT_MAX_FEEDRATE          {500, 500, 5, 25}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {5000,5000,100,80000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          1750 //1500    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  5000   // X, Y, Z and E max acceleration in mm/s^2 for r retracts
+
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+// #define EXTRUDER_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
+
+// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
+#define DEFAULT_XYJERK                10   // (mm/sec)
+#define DEFAULT_ZJERK                 0.3  //0.4   // (mm/sec)
+#define DEFAULT_EJERK                 5.0    // (mm/sec)
+
+
+//=============================================================================
+//============================= Additional Features ===========================
+//=============================================================================
+
+// Custom M code points
+#define CUSTOM_M_CODES
+#ifdef CUSTOM_M_CODES
+  #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
+  #define Z_PROBE_OFFSET_RANGE_MIN -15
+  #define Z_PROBE_OFFSET_RANGE_MAX -5
+#endif
+
+
+// EEPROM
+// The microcontroller can store settings in the EEPROM, e.g. max velocity...
+// M500 - stores parameters in EEPROM
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
+// M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
+//define this to enable EEPROM support
+//#define EEPROM_SETTINGS
+//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
+// please keep turned on if you can.
+//#define EEPROM_CHITCHAT
+
+// Preheat Constants
+#define PLA_PREHEAT_HOTEND_TEMP 180
+#define PLA_PREHEAT_HPB_TEMP 70
+#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+
+#define ABS_PREHEAT_HOTEND_TEMP 240
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+
+//==============================LCD and SD support=============================
+
+// Define your display language below. Replace (en) with your language code and uncomment.
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// See also language.h
+//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
+
+// Character based displays can have different extended charsets.
+//#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+
+//#define ULTRA_LCD  //general LCD support, also 16x2
+//#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
+//#define SDSUPPORT // Enable SD Card Support in Hardware Console
+//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
+//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
+//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
+//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
+//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
+//#define ULTIPANEL  //the UltiPanel as on Thingiverse
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+
+// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
+// http://reprap.org/wiki/PanelOne
+//#define PANEL_ONE
+
+// The MaKr3d Makr-Panel with graphic controller and SD support
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//#define MAKRPANEL
+
+// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD
+// http://panucatt.com
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define VIKI2
+//#define miniVIKI
+
+// The RepRapDiscount Smart Controller (white PCB)
+// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
+//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+
+// The GADGETS3D G3D LCD/SD Controller (blue PCB)
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+//#define G3D_PANEL
+
+// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
+// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
+// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
+//#define REPRAPWORLD_KEYPAD
+//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
+
+// The Elefu RA Board Control Panel
+// http://www.elefu.com/index.php?route=product/product&product_id=53
+// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
+//#define RA_CONTROL_PANEL
+
+//automatic expansion
+#if defined (MAKRPANEL)
+ #define DOGLCD
+ #define SDSUPPORT
+ #define ULTIPANEL
+ #define NEWPANEL
+ #define DEFAULT_LCD_CONTRAST 17
+#endif
+
+#if defined(miniVIKI) || defined(VIKI2)
+ #define ULTRA_LCD  //general LCD support, also 16x2
+ #define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
+ #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
+
+  #ifdef miniVIKI
+   #define DEFAULT_LCD_CONTRAST 95
+  #else
+   #define DEFAULT_LCD_CONTRAST 40
+  #endif
+
+ #define ENCODER_PULSES_PER_STEP 4
+ #define ENCODER_STEPS_PER_MENU_ITEM 1
+#endif
+
+#if defined (PANEL_ONE)
+ #define SDSUPPORT
+ #define ULTIMAKERCONTROLLER
+#endif
+
+#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+ #define DOGLCD
+ #define U8GLIB_ST7920
+ #define REPRAP_DISCOUNT_SMART_CONTROLLER
+#endif
+
+#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
+ #define ULTIPANEL
+ #define NEWPANEL
+#endif
+
+#if defined(REPRAPWORLD_KEYPAD)
+  #define NEWPANEL
+  #define ULTIPANEL
+#endif
+#if defined(RA_CONTROL_PANEL)
+ #define ULTIPANEL
+ #define NEWPANEL
+ #define LCD_I2C_TYPE_PCA8574
+ #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
+#endif
+
+//I2C PANELS
+
+//#define LCD_I2C_SAINSMART_YWROBOT
+#ifdef LCD_I2C_SAINSMART_YWROBOT
+  // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
+  // Make sure it is placed in the Arduino libraries directory.
+  #define LCD_I2C_TYPE_PCF8575
+  #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
+  #define NEWPANEL
+  #define ULTIPANEL
+#endif
+
+// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
+//#define LCD_I2C_PANELOLU2
+#ifdef LCD_I2C_PANELOLU2
+  // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+  // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+  // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
+  // Note: The PANELOLU2 encoder click input can either be directly connected to a pin
+  //       (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
+  #define LCD_I2C_TYPE_MCP23017
+  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+  #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
+  #define NEWPANEL
+  #define ULTIPANEL
+
+  #ifndef ENCODER_PULSES_PER_STEP
+	#define ENCODER_PULSES_PER_STEP 4
+  #endif
+
+  #ifndef ENCODER_STEPS_PER_MENU_ITEM
+	#define ENCODER_STEPS_PER_MENU_ITEM 1
+  #endif
+
+
+  #ifdef LCD_USE_I2C_BUZZER
+	#define LCD_FEEDBACK_FREQUENCY_HZ 1000
+	#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
+  #endif
+
+#endif
+
+// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
+//#define LCD_I2C_VIKI
+#ifdef LCD_I2C_VIKI
+  // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+  // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+  // Note: The pause/stop/resume LCD button pin should be connected to the Arduino
+  //       BTN_ENC pin (or set BTN_ENC to -1 if not used)
+  #define LCD_I2C_TYPE_MCP23017
+  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+  #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
+  #define NEWPANEL
+  #define ULTIPANEL
+#endif
+
+// Shift register panels
+// ---------------------
+// 2 wire Non-latching LCD SR from:
+// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
+
+//#define SAV_3DLCD
+#ifdef SAV_3DLCD
+   #define SR_LCD_2W_NL    // Non latching 2 wire shiftregister
+   #define NEWPANEL
+   #define ULTIPANEL
+#endif
+
+
+#ifdef ULTIPANEL
+//  #define NEWPANEL  //enable this if you have a click-encoder panel
+  #define SDSUPPORT
+  #define ULTRA_LCD
+  #ifdef DOGLCD // Change number of lines to match the DOG graphic display
+    #define LCD_WIDTH 22
+    #define LCD_HEIGHT 5
+  #else
+    #define LCD_WIDTH 20
+    #define LCD_HEIGHT 4
+  #endif
+#else //no panel but just LCD
+  #ifdef ULTRA_LCD
+  #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
+    #define LCD_WIDTH 22
+    #define LCD_HEIGHT 5
+  #else
+    #define LCD_WIDTH 16
+    #define LCD_HEIGHT 2
+  #endif
+  #endif
+#endif
+
+// default LCD contrast for dogm-like LCD displays
+#ifdef DOGLCD
+# ifndef DEFAULT_LCD_CONTRAST
+#  define DEFAULT_LCD_CONTRAST 32
+# endif
+#endif
+
+// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
+#define FAST_PWM_FAN
+
+// Temperature status LEDs that display the hotend and bet temperature.
+// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
+// Otherwise the RED led is on. There is 1C hysteresis.
+//#define TEMP_STAT_LEDS
+
+// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
+// is too low, you should also increment SOFT_PWM_SCALE.
+//#define FAN_SOFT_PWM
+
+// Incrementing this by 1 will double the software PWM frequency,
+// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
+// However, control resolution will be halved for each increment;
+// at zero value, there are 128 effective control positions.
+#define SOFT_PWM_SCALE 0
+
+// M240  Triggers a camera by emulating a Canon RC-1 Remote
+// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
+// #define PHOTOGRAPH_PIN     23
+
+// SF send wrong arc g-codes when using Arc Point as fillet procedure
+//#define SF_ARC_FIX
+
+// Support for the BariCUDA Paste Extruder.
+//#define BARICUDA
+
+//define BlinkM/CyzRgb Support
+//#define BLINKM
+
+/*********************************************************************\
+* R/C SERVO support
+* Sponsored by TrinityLabs, Reworked by codexmas
+**********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it undefined or defining as 0 will disable the servo subsystem
+// If unsure, leave commented / disabled
+//
+//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+
+// Servo Endstops
+//
+// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
+// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
+//
+//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
+//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
+
+/**********************************************************************\
+ * Support for a filament diameter sensor
+ * Also allows adjustment of diameter at print time (vs  at slicing)
+ * Single extruder only at this point (extruder 0)
+ *
+ * Motherboards
+ * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 - Rambo  - uses Analog input 3
+ * Note may require analog pins to be defined for different motherboards
+ **********************************************************************/
+// Uncomment below to enable
+//#define FILAMENT_SENSOR
+
+#define FILAMENT_SENSOR_EXTRUDER_NUM	0  //The number of the extruder that has the filament sensor (0,1,2)
+#define MEASUREMENT_DELAY_CM			14  //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA  3.0  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+#define MEASURED_UPPER_LIMIT          3.30  //upper limit factor used for sensor reading validation in mm
+#define MEASURED_LOWER_LIMIT          1.90  //lower limit factor for sensor reading validation in mm
+#define MAX_MEASUREMENT_DELAY			20  //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
+
+//defines used in the code
+#define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially
+
+//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
+//#define FILAMENT_LCD_DISPLAY
+
+
+#include "Configuration_adv.h"
+#include "thermistortables.h"
+
+#endif //__CONFIGURATION_H

Marlin/pins_FELIX2.h

@@ -1,112 +1,42 @@
-/****************************************************************************************
-* FELIXprinters v2.0/3.0 pin assignment
-*
-****************************************************************************************/
-#if MOTHERBOARD == BOARD_FELIX2
-#define KNOWN_BOARD 1
+/**
+ * FELIXprinters v2.0/3.0 (RAMPS v1.3) pin assignments
+ */
 
-//////////////////FIX THIS//////////////
-#ifndef __AVR_ATmega1280__
-#ifndef __AVR_ATmega2560__
-#error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
-#endif
-#endif
+#include "pins_RAMPS_13.h"
 
-#define LARGE_FLASH        true
-
-#define X_STEP_PIN         54
-#define X_DIR_PIN          55
-#define X_ENABLE_PIN       38
-#define X_MIN_PIN           3
-#define X_MAX_PIN           -1
-
-#define Y_STEP_PIN         60
-#define Y_DIR_PIN          61
-#define Y_ENABLE_PIN       56
-#define Y_MIN_PIN          14
+#define X_MAX_PIN          -1
 #define Y_MAX_PIN          -1
-
-#define Z_STEP_PIN         46
-#define Z_DIR_PIN          48
-#define Z_ENABLE_PIN       62
-#define Z_MIN_PIN          18
 #define Z_MAX_PIN          -1
 
+#define Y2_STEP_PIN        -1
+#define Y2_DIR_PIN         -1
+#define Y2_ENABLE_PIN      -1
 #define Z2_STEP_PIN        -1
 #define Z2_DIR_PIN         -1
 #define Z2_ENABLE_PIN      -1
 
-#define E0_STEP_PIN        26
-#define E0_DIR_PIN         28
-#define E0_ENABLE_PIN      24
-
-#define E1_STEP_PIN        36
+#define E1_STEP_PIN        36 // FELIX E1 uses RAMPS Y2/Z2 pins
 #define E1_DIR_PIN         34
 #define E1_ENABLE_PIN      30
 
-#define SDPOWER            1
-#define SDSS               53
-#define LED_PIN            13
+#define SDPOWER             1
 
-#define FAN_PIN            9 // (Sprinter config)
+#define FAN_PIN             9 // (Sprinter config)
 #define PS_ON_PIN          12
 
-#define KILL_PIN           -1
-
-#define HEATER_0_PIN       10   // EXTRUDER 1
-#define HEATER_1_PIN       7    // EXTRUDER 2 (FAN On Sprinter)
-#define HEATER_2_PIN       -1
-#define HEATER_BED_PIN     8    // BED
-
-#define TEMP_0_PIN         13   // ANALOG NUMBERING
-#define TEMP_1_PIN         15   // ANALOG NUMBERING
-#define TEMP_2_PIN         -1   // ANALOG NUMBERING
-
-#define TEMP_BED_PIN       14   // ANALOG NUMBERING
-
-#ifdef ULTRA_LCD
-
-#ifdef NEWPANEL
-//encoder rotation values
-#define encrot0 0
-#define encrot1 2
-#define encrot2 3
-#define encrot3 1
-
-#define BLEN_A 0
-#define BLEN_B 1
-#define BLEN_C 2
-
-#define LCD_PINS_RS 16
-#define LCD_PINS_ENABLE 17
-#define LCD_PINS_D4 23
-#define LCD_PINS_D5 25
-#define LCD_PINS_D6 27
-#define LCD_PINS_D7 29
-
-//arduino pin which triggers an piezzo beeper
-#define BEEPER 33	 // Beeper on AUX-4
-
-//buttons are directly attached using AUX-2
-#define BTN_EN1 37
-#define BTN_EN2 35
-#define BTN_ENC 31  //the click
-
-#define SDCARDDETECT 6  // Ramps does not use this port
-#endif //NEWPANEL
-#endif //ULTRA_LCD
+#define HEATER_1_PIN        7   // EXTRUDER 2
 
-// SPI for Max6675 Thermocouple
+#if defined(ULTRA_LCD) && defined(NEWPANEL)
+  //encoder rotation values
+  #define encrot0 0
+  #define encrot1 2
+  #define encrot2 3
+  #define encrot3 1
 
-#ifndef SDSUPPORT
-// these pins are defined in the SD library if building with SD support
-#define MAX_SCK_PIN          52
-#define MAX_MISO_PIN         50
-#define MAX_MOSI_PIN         51
-#define MAX6675_SS       53
-#else
-#define MAX6675_SS       49
-#endif
+  #define BLEN_C 2
+  #define BLEN_B 1
+  #define BLEN_A 0
 
-#endif//MOTHERBOARD == BOARD_FELIX2
+  #define SDCARDDETECT 6
 
+#endif // NEWPANEL && ULTRA_LCD