M851 XY 3 point followup (incomplete) (#15361)

Marlin/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp

@@ -1381,6 +1381,8 @@
 
   #if HAS_BED_PROBE
 
+    //#define VALIDATE_MESH_TILT
+
     #include "../../../libs/vector_3.h"
 
     void unified_bed_leveling::tilt_mesh_based_on_probed_grid(const bool do_3_pt_leveling) {
@@ -1392,7 +1394,9 @@
       float measured_z;
       bool abort_flag = false;
 
-      //float z1, z2, z3;  // Needed for algorithm validation below
+      #ifdef VALIDATE_MESH_TILT
+        float z1, z2, z3;  // Needed for algorithm validation below
+      #endif
 
       struct linear_fit_data lsf_results;
       incremental_LSF_reset(&lsf_results);
@@ -1403,17 +1407,19 @@
           ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 1/3"));
         #endif
 
-        measured_z = probe_at_point(PROBE_PT_1_X, PROBE_PT_1_Y, PROBE_PT_RAISE, g29_verbose_level);
+        measured_z = probe_at_point(x_min, y_min, PROBE_PT_RAISE, g29_verbose_level);
         if (isnan(measured_z))
           abort_flag = true;
         else {
-          measured_z -= get_z_correction(PROBE_PT_1_X, PROBE_PT_1_Y);
-          //z1 = measured_z;
+          measured_z -= get_z_correction(x_min, y_min);
+          #ifdef VALIDATE_MESH_TILT
+            z1 = measured_z;
+          #endif
           if (g29_verbose_level > 3) {
             serial_spaces(16);
             SERIAL_ECHOLNPAIR("Corrected_Z=", measured_z);
           }
-          incremental_LSF(&lsf_results, PROBE_PT_1_X, PROBE_PT_1_Y, measured_z);
+          incremental_LSF(&lsf_results, x_min, y_min, measured_z);
         }
 
         if (!abort_flag) {
@@ -1422,17 +1428,19 @@
             ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 2/3"));
           #endif
 
-          measured_z = probe_at_point(PROBE_PT_2_X, PROBE_PT_2_Y, PROBE_PT_RAISE, g29_verbose_level);
-          //z2 = measured_z;
+          measured_z = probe_at_point(x_max, y_min, PROBE_PT_RAISE, g29_verbose_level);
+          #ifdef VALIDATE_MESH_TILT
+            z2 = measured_z;
+          #endif
           if (isnan(measured_z))
             abort_flag = true;
           else {
-            measured_z -= get_z_correction(PROBE_PT_2_X, PROBE_PT_2_Y);
+            measured_z -= get_z_correction(x_max, y_min);
             if (g29_verbose_level > 3) {
               serial_spaces(16);
               SERIAL_ECHOLNPAIR("Corrected_Z=", measured_z);
             }
-            incremental_LSF(&lsf_results, PROBE_PT_2_X, PROBE_PT_2_Y, measured_z);
+            incremental_LSF(&lsf_results, x_max, y_min, measured_z);
           }
         }
 
@@ -1442,17 +1450,20 @@
             ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 3/3"));
           #endif
 
-          measured_z = probe_at_point(PROBE_PT_3_X, PROBE_PT_3_Y, PROBE_PT_STOW, g29_verbose_level);
-          //z3 = measured_z;
+          const float center_probe = (x_max - x_min) / 2;
+          measured_z = probe_at_point(center_probe, y_max, PROBE_PT_STOW, g29_verbose_level);
+          #ifdef VALIDATE_MESH_TILT
+            z3 = measured_z;
+          #endif
           if (isnan(measured_z))
             abort_flag = true;
           else {
-            measured_z -= get_z_correction(PROBE_PT_3_X, PROBE_PT_3_Y);
+            measured_z -= get_z_correction(center_probe, y_max);
             if (g29_verbose_level > 3) {
               serial_spaces(16);
               SERIAL_ECHOLNPAIR("Corrected_Z=", measured_z);
             }
-            incremental_LSF(&lsf_results, PROBE_PT_3_X, PROBE_PT_3_Y, measured_z);
+            incremental_LSF(&lsf_results, center_probe, y_max, measured_z);
           }
         }
 
@@ -1598,34 +1609,34 @@
          * is calculated.  The Z error between the probed point locations and the get_z_correction()
          * numbers for those locations should be 0.
          */
-        #if 0
-        float t, t1, d;
-        t = normal.x * (PROBE_PT_1_X) + normal.y * (PROBE_PT_1_Y);
-        d = t + normal.z * z1;
-        DEBUG_ECHOPAIR_F("D from 1st point: ", d, 6);
-        DEBUG_ECHOLNPAIR_F("   Z error: ", normal.z*z1-get_z_correction(PROBE_PT_1_X, PROBE_PT_1_Y), 6);
-
-        t = normal.x * (PROBE_PT_2_X) + normal.y * (PROBE_PT_2_Y);
-        d = t + normal.z * z2;
-        DEBUG_EOL();
-        DEBUG_ECHOPAIR_F("D from 2nd point: ", d, 6);
-        DEBUG_ECHOLNPAIR_F("   Z error: ", normal.z*z2-get_z_correction(PROBE_PT_2_X, PROBE_PT_2_Y), 6);
-
-        t = normal.x * (PROBE_PT_3_X) + normal.y * (PROBE_PT_3_Y);
-        d = t + normal.z * z3;
-        DEBUG_ECHOPAIR_F("D from 3rd point: ", d, 6);
-        DEBUG_ECHOLNPAIR_F("   Z error: ", normal.z*z3-get_z_correction(PROBE_PT_3_X, PROBE_PT_3_Y), 6);
-
-        t = normal.x * (Z_SAFE_HOMING_X_POINT) + normal.y * (Z_SAFE_HOMING_Y_POINT);
-        d = t + normal.z * 0;
-        DEBUG_ECHOLNPAIR_F("D from home location with Z=0 : ", d, 6);
-
-        t = normal.x * (Z_SAFE_HOMING_X_POINT) + normal.y * (Z_SAFE_HOMING_Y_POINT);
-        d = t + get_z_correction(Z_SAFE_HOMING_X_POINT, Z_SAFE_HOMING_Y_POINT); // normal.z * 0;
-        DEBUG_ECHOPAIR_F("D from home location using mesh value for Z: ", d, 6);
-
-        DEBUG_ECHOPAIR("   Z error: (", Z_SAFE_HOMING_X_POINT, ",", Z_SAFE_HOMING_Y_POINT);
-        DEBUG_ECHOLNPAIR_F(") = ", get_z_correction(Z_SAFE_HOMING_X_POINT, Z_SAFE_HOMING_Y_POINT), 6);
+        #ifdef VALIDATE_MESH_TILT
+          float t, t1, d;
+          t = normal.x * x_min + normal.y * y_min;
+          d = t + normal.z * z1;
+          DEBUG_ECHOPAIR_F("D from 1st point: ", d, 6);
+          DEBUG_ECHOLNPAIR_F("   Z error: ", normal.z * z1 - get_z_correction(x_min, y_min), 6);
+
+          t = normal.x * x_max + normal.y * y_min;
+          d = t + normal.z * z2;
+          DEBUG_EOL();
+          DEBUG_ECHOPAIR_F("D from 2nd point: ", d, 6);
+          DEBUG_ECHOLNPAIR_F("   Z error: ", normal.z * z2 - get_z_correction(x_max, y_min), 6);
+
+          t = normal.x * ((x_max - x_min) / 2) + normal.y * (y_min);
+          d = t + normal.z * z3;
+          DEBUG_ECHOPAIR_F("D from 3rd point: ", d, 6);
+          DEBUG_ECHOLNPAIR_F("   Z error: ", normal.z * z3 - get_z_correction((x_max - x_min) / 2, y_max), 6);
+
+          t = normal.x * (Z_SAFE_HOMING_X_POINT) + normal.y * (Z_SAFE_HOMING_Y_POINT);
+          d = t + normal.z * 0;
+          DEBUG_ECHOLNPAIR_F("D from home location with Z=0 : ", d, 6);
+
+          t = normal.x * (Z_SAFE_HOMING_X_POINT) + normal.y * (Z_SAFE_HOMING_Y_POINT);
+          d = t + get_z_correction(Z_SAFE_HOMING_X_POINT, Z_SAFE_HOMING_Y_POINT); // normal.z * 0;
+          DEBUG_ECHOPAIR_F("D from home location using mesh value for Z: ", d, 6);
+
+          DEBUG_ECHOPAIR("   Z error: (", Z_SAFE_HOMING_X_POINT, ",", Z_SAFE_HOMING_Y_POINT);
+          DEBUG_ECHOLNPAIR_F(") = ", get_z_correction(Z_SAFE_HOMING_X_POINT, Z_SAFE_HOMING_Y_POINT), 6);
         #endif
       } // DEBUGGING(LEVELING)
 

Marlin/src/gcode/bedlevel/abl/G29.cpp

@@ -266,10 +266,11 @@ G29_TYPE GcodeSuite::G29() {
     #endif
 
     // Probe at 3 arbitrary points
+    const float x_min = probe_min_x(), x_max = probe_max_x(), y_min = probe_min_y(), y_max = probe_max_y();
     ABL_VAR vector_3 points[3] = {
-      vector_3(PROBE_PT_1_X, PROBE_PT_1_Y, 0),
-      vector_3(PROBE_PT_2_X, PROBE_PT_2_Y, 0),
-      vector_3(PROBE_PT_3_X, PROBE_PT_3_Y, 0)
+      vector_3(x_min, y_min, 0),
+      vector_3(x_max, y_min, 0),
+      vector_3((x_max - x_min) / 2, y_max, 0)
     };
 
   #endif // AUTO_BED_LEVELING_3POINT

Marlin/src/inc/Conditionals_post.h

@@ -200,6 +200,10 @@
   #undef SLOWDOWN
 #endif
 
+#ifndef MESH_INSET
+  #define MESH_INSET 0
+#endif
+
 /**
  * Safe Homing Options
  */
@@ -1490,15 +1494,6 @@ constexpr float nozzle_to_probe_offset[XYZ] = NOZZLE_TO_PROBE_OFFSET;
   #define PROBE_Y_MIN (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
   #define PROBE_X_MAX (X_CENTER +  SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
   #define PROBE_Y_MAX (Y_CENTER +  SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
-
-#else
-
-  // Boundaries for Cartesian probing based on bed limits
-  #define PROBE_X_MIN (_MAX(X_MIN_BED + MIN_PROBE_EDGE, X_MIN_POS + nozzle_to_probe_offset[X_AXIS]))
-  #define PROBE_Y_MIN (_MAX(Y_MIN_BED + MIN_PROBE_EDGE, Y_MIN_POS + nozzle_to_probe_offset[Y_AXIS]))
-  #define PROBE_X_MAX (_MIN(X_MAX_BED - (MIN_PROBE_EDGE), X_MAX_POS + nozzle_to_probe_offset[X_AXIS]))
-  #define PROBE_Y_MAX (_MIN(Y_MAX_BED - (MIN_PROBE_EDGE), Y_MAX_POS + nozzle_to_probe_offset[Y_AXIS]))
-
 #endif
 
 #if ENABLED(SEGMENT_LEVELED_MOVES) && !defined(LEVELED_SEGMENT_LENGTH)
@@ -1508,7 +1503,7 @@ constexpr float nozzle_to_probe_offset[XYZ] = NOZZLE_TO_PROBE_OFFSET;
 /**
  * Default mesh area is an area with an inset margin on the print area.
  */
-#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
+#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_BILINEAR)
   #if IS_KINEMATIC
     // Probing points may be verified at compile time within the radius
     // using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
@@ -1548,54 +1543,6 @@ constexpr float nozzle_to_probe_offset[XYZ] = NOZZLE_TO_PROBE_OFFSET;
 
 #endif // MESH_BED_LEVELING || AUTO_BED_LEVELING_UBL
 
-#if EITHER(AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_3POINT)
-  #if IS_KINEMATIC
-    #define SIN0    0.0
-    #define SIN120  0.866025
-    #define SIN240 -0.866025
-    #define COS0    1.0
-    #define COS120 -0.5
-    #define COS240 -0.5
-    #ifndef PROBE_PT_1_X
-      #define PROBE_PT_1_X (X_CENTER + (_PROBE_RADIUS) * COS0)
-    #endif
-    #ifndef PROBE_PT_1_Y
-      #define PROBE_PT_1_Y (Y_CENTER + (_PROBE_RADIUS) * SIN0)
-    #endif
-    #ifndef PROBE_PT_2_X
-      #define PROBE_PT_2_X (X_CENTER + (_PROBE_RADIUS) * COS120)
-    #endif
-    #ifndef PROBE_PT_2_Y
-      #define PROBE_PT_2_Y (Y_CENTER + (_PROBE_RADIUS) * SIN120)
-    #endif
-    #ifndef PROBE_PT_3_X
-      #define PROBE_PT_3_X (X_CENTER + (_PROBE_RADIUS) * COS240)
-    #endif
-    #ifndef PROBE_PT_3_Y
-      #define PROBE_PT_3_Y (Y_CENTER + (_PROBE_RADIUS) * SIN240)
-    #endif
-  #else
-    #ifndef PROBE_PT_1_X
-      #define PROBE_PT_1_X PROBE_X_MIN
-    #endif
-    #ifndef PROBE_PT_1_Y
-      #define PROBE_PT_1_Y PROBE_Y_MIN
-    #endif
-    #ifndef PROBE_PT_2_X
-      #define PROBE_PT_2_X PROBE_X_MAX
-    #endif
-    #ifndef PROBE_PT_2_Y
-      #define PROBE_PT_2_Y PROBE_Y_MIN
-    #endif
-    #ifndef PROBE_PT_3_X
-      #define PROBE_PT_3_X X_CENTER
-    #endif
-    #ifndef PROBE_PT_3_Y
-      #define PROBE_PT_3_Y PROBE_Y_MAX
-    #endif
-  #endif
-#endif
-
 /**
  * Buzzer/Speaker
  */

Marlin/src/inc/SanityCheck.h

@@ -248,9 +248,11 @@
 #elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X) || defined(UBL_MESH_MAX_Y)
   #error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration."
 #elif defined(ABL_PROBE_PT_1_X) || defined(ABL_PROBE_PT_1_Y) || defined(ABL_PROBE_PT_2_X) || defined(ABL_PROBE_PT_2_Y) || defined(ABL_PROBE_PT_3_X) || defined(ABL_PROBE_PT_3_Y)
-  #error "ABL_PROBE_PT_[123]_[XY] is now PROBE_PT_[123]_[XY]. Please update your configuration."
+  #error "ABL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
 #elif defined(UBL_PROBE_PT_1_X) || defined(UBL_PROBE_PT_1_Y) || defined(UBL_PROBE_PT_2_X) || defined(UBL_PROBE_PT_2_Y) || defined(UBL_PROBE_PT_3_X) || defined(UBL_PROBE_PT_3_Y)
-  #error "UBL_PROBE_PT_[123]_[XY] is now PROBE_PT_[123]_[XY]. Please update your configuration."
+  #error "UBL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
+#elif defined(PROBE_PT_1_X) || defined(PROBE_PT_1_Y) || defined(PROBE_PT_2_X) || defined(PROBE_PT_2_Y) || defined(PROBE_PT_3_X) || defined(PROBE_PT_3_Y)
+  #error "PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
 #elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY)
   #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration."
 #elif defined(BABYSTEP_ZPROBE_GFX_REVERSE)
@@ -1206,19 +1208,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
  * Bed Leveling Requirements
  */
 
-//
-// !! TODO: REPLACE WITH TESTS IN THE 3-POINT LEVELING CODE !!
-//
-
-//#if EITHER(AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_3POINT)
-//  static_assert(WITHIN(PROBE_PT_1_X, PROBE_X_MIN, PROBE_X_MAX), "PROBE_PT_1_X is outside the probe region.");
-//  static_assert(WITHIN(PROBE_PT_2_X, PROBE_X_MIN, PROBE_X_MAX), "PROBE_PT_2_X is outside the probe region.");
-//  static_assert(WITHIN(PROBE_PT_3_X, PROBE_X_MIN, PROBE_X_MAX), "PROBE_PT_3_X is outside the probe region.");
-//  static_assert(WITHIN(PROBE_PT_1_Y, PROBE_Y_MIN, PROBE_Y_MAX), "PROBE_PT_1_Y is outside the probe region.");
-//  static_assert(WITHIN(PROBE_PT_2_Y, PROBE_Y_MIN, PROBE_Y_MAX), "PROBE_PT_2_Y is outside the probe region.");
-//  static_assert(WITHIN(PROBE_PT_3_Y, PROBE_Y_MIN, PROBE_Y_MAX), "PROBE_PT_3_Y is outside the probe region.");
-//#endif
-
 #if ENABLED(AUTO_BED_LEVELING_UBL)
 
   /**
@@ -1318,12 +1307,9 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
  * Make sure Z_SAFE_HOMING point is reachable
  */
 #if ENABLED(Z_SAFE_HOMING)
-  #if HAS_BED_PROBE
-    //
-    // !! TODO: REPLACE WITH TESTS IN THE Z_SAFE_HOMING CODE !!
-    //
-    //static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, PROBE_X_MIN, PROBE_X_MAX), "Z_SAFE_HOMING_X_POINT is outside the probe region.");
-    //static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, PROBE_Y_MIN, PROBE_Y_MAX), "Z_SAFE_HOMING_Y_POINT is outside the probe region.");
+  #if HAS_BED_PROBE && (ENABLED(DELTA) || IS_SCARA)
+    static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, PROBE_X_MIN, PROBE_X_MAX), "Z_SAFE_HOMING_X_POINT is outside the probe region.");
+    static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, PROBE_Y_MIN, PROBE_Y_MAX), "Z_SAFE_HOMING_Y_POINT is outside the probe region.");
   #else
     static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, X_MIN_POS, X_MAX_POS), "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle.");
     static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, Y_MIN_POS, Y_MAX_POS), "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle.");

buildroot/share/tests/LPC1769-tests

@@ -44,13 +44,13 @@ exec_test $1 $2 "Smoothieboard with many features"
 restore_configs
 use_example_configs delta/generic
 opt_set MOTHERBOARD BOARD_COHESION3D_REMIX
-opt_enable AUTO_BED_LEVELING_BILINEAR EEPROM_SETTINGS EEPROM_CHITCHAT BAUD_RATE_GCODE
-opt_disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 opt_set X_DRIVER_TYPE TMC2130
 opt_set Y_DRIVER_TYPE TMC2130
 opt_set Z_DRIVER_TYPE TMC2130
-opt_enable TMC_USE_SW_SPI MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z HYBRID_THRESHOLD TMC_DEBUG \
-           SENSORLESS_PROBING X_STALL_SENSITIVITY Y_STALL_SENSITIVITY Z_STALL_SENSITIVITY
+opt_enable AUTO_BED_LEVELING_BILINEAR EEPROM_SETTINGS EEPROM_CHITCHAT BAUD_RATE_GCODE \
+           TMC_USE_SW_SPI MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z HYBRID_THRESHOLD \
+           SENSORLESS_PROBING X_STALL_SENSITIVITY Y_STALL_SENSITIVITY Z_STALL_SENSITIVITY TMC_DEBUG
+opt_disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 exec_test $1 $2 "Cohesion3D Remix DELTA + ABL Bilinear + EEPROM + SENSORLESS_PROBING"
 
 # clean up

config/default/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -1258,19 +1258,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -1253,19 +1253,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -1253,19 +1253,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -1272,19 +1272,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -1331,19 +1331,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Alfawise/U20/Configuration.h

@@ -1331,19 +1331,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/AliExpress/CL-260/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -1263,19 +1263,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Anet/A2/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Anet/A2plus/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Anet/A6/Configuration.h

@@ -1357,19 +1357,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Anet/A8plus/Configuration.h

@@ -1263,19 +1263,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Anet/E16/Configuration.h

@@ -1264,19 +1264,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/AnyCubic/i3/Configuration.h

@@ -1262,19 +1262,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/ArmEd/Configuration.h

@@ -1253,19 +1253,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Azteeg/X5GT/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/BIBO/TouchX/default/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/BQ/Hephestos/Configuration.h

@@ -1240,19 +1240,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/BQ/Hephestos_2/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/BQ/WITBOX/Configuration.h

@@ -1240,19 +1240,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Cartesio/Configuration.h

@@ -1251,19 +1251,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/CR-10/Configuration.h

@@ -1262,19 +1262,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/CR-10S/Configuration.h

@@ -1253,19 +1253,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/CR-10_5S/Configuration.h

@@ -1255,19 +1255,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/CR-10mini/Configuration.h

@@ -1271,19 +1271,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/CR-20 Pro/Configuration.h

@@ -1255,19 +1255,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/CR-20/Configuration.h

@@ -1255,19 +1255,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/CR-8/Configuration.h

@@ -1262,19 +1262,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/Ender-2/Configuration.h

@@ -1256,19 +1256,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/Ender-3/Configuration.h

@@ -1256,19 +1256,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/Ender-4/Configuration.h

@@ -1262,19 +1262,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Creality/Ender-5/Configuration.h

@@ -1255,19 +1255,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Dagoma/Disco Ultimate/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Einstart-S/Configuration.h

@@ -1262,19 +1262,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/FYSETC/AIO_II/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/FYSETC/Cheetah 1.2/base/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/FYSETC/Cheetah/BLTouch/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/FYSETC/Cheetah/base/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/FYSETC/F6_13/Configuration.h

@@ -1254,19 +1254,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Felix/Configuration.h

@@ -1234,19 +1234,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Felix/DUAL/Configuration.h

@@ -1234,19 +1234,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -1245,19 +1245,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/A10/Configuration.h

@@ -1237,19 +1237,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/A10M/Configuration.h

@@ -1237,19 +1237,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/A20M/Configuration.h

@@ -1237,19 +1237,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/GT2560/Configuration.h

@@ -1267,19 +1267,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -1259,19 +1259,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -1273,19 +1273,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -1272,19 +1272,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/HMS434/Configuration.h

@@ -1239,19 +1239,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Infitary/i3-M508/Configuration.h

@@ -1256,19 +1256,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/JGAurora/A1/Configuration.h

@@ -1259,19 +1259,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/JGAurora/A5/Configuration.h

@@ -1264,19 +1264,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/JGAurora/A5S/Configuration.h

@@ -1259,19 +1259,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/MakerParts/Configuration.h

@@ -1272,19 +1272,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Malyan/M200/Configuration.h

@@ -1251,19 +1251,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Micromake/C1/basic/Configuration.h

@@ -1256,19 +1256,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Micromake/C1/enhanced/Configuration.h

@@ -1256,19 +1256,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Mks/Robin/Configuration.h

@@ -1253,19 +1253,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Mks/Sbase/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Printrbot/PrintrboardG2/Configuration.h

@@ -1260,19 +1260,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/RapideLite/RL200/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/RepRapPro/Huxley/Configuration.h

@@ -1301,19 +1301,6 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/RigidBot/Configuration.h

@@ -1250,19 +1250,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/SCARA/Configuration.h

@@ -1261,19 +1261,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/STM32/Black_STM32F407VET6/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/STM32/STM32F103R/Configuration.h

@@ -1254,19 +1254,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/STM32/STM32F4/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/STM32/stm32f103ret6/Configuration.h

@@ -1254,19 +1254,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Sanguinololu/Configuration.h

@@ -1283,19 +1283,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tevo/Michelangelo/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tevo/Tarantula Pro/Configuration.h

@@ -1250,19 +1250,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h

@@ -1257,19 +1257,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/TheBorg/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/TinyBoy2/Configuration.h

@@ -1308,19 +1308,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tronxy/X1/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tronxy/X3A/Configuration.h

@@ -1256,19 +1256,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tronxy/X5S-2E/Configuration.h

@@ -1273,19 +1273,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tronxy/X5S/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Tronxy/XY100/Configuration.h

@@ -1263,19 +1263,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/UltiMachine/Archim1/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/UltiMachine/Archim2/Configuration.h

@@ -1252,19 +1252,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/VORONDesign/Configuration.h

@@ -1261,19 +1261,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */

config/examples/Velleman/K8200/Configuration.h

@@ -1282,19 +1282,6 @@
 #endif // BED_LEVELING
 
 /**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
-/**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */