|
|
@@ -0,0 +1,103 @@
|
|
|
1
|
+# Implemented G Codes
|
|
|
2
|
+
|
|
|
3
|
+## G Codes
|
|
|
4
|
+
|
|
|
5
|
+* G0 -> G1
|
|
|
6
|
+* G1 - Coordinated Movement X Y Z E
|
|
|
7
|
+* G2 - CW ARC
|
|
|
8
|
+* G3 - CCW ARC
|
|
|
9
|
+* G4 - Dwell S<seconds> or P<milliseconds>
|
|
|
10
|
+* G10 - retract filament according to settings of M207
|
|
|
11
|
+* G11 - retract recover filament according to settings of M208
|
|
|
12
|
+* G28 - Home all Axis
|
|
|
13
|
+* G29 - Detailed Z-Probe, probes the bed at 3 points. You must de at the home position for this to work correctly.
|
|
|
14
|
+* G30 - Single Z Probe, probes bed at current XY location.
|
|
|
15
|
+* G31 - Dock Z Probe sled (if enabled)
|
|
|
16
|
+* G32 - Undock Z Probe sled (if enabled)
|
|
|
17
|
+* G90 - Use Absolute Coordinates
|
|
|
18
|
+* G91 - Use Relative Coordinates
|
|
|
19
|
+* G92 - Set current position to cordinates given
|
|
|
20
|
+
|
|
|
21
|
+## M Codes
|
|
|
22
|
+* M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled)
|
|
|
23
|
+* M1 - Same as M0
|
|
|
24
|
+* M17 - Enable/Power all stepper motors
|
|
|
25
|
+* M18 - Disable all stepper motors; same as M84
|
|
|
26
|
+* M20 - List SD card
|
|
|
27
|
+* M21 - Init SD card
|
|
|
28
|
+* M22 - Release SD card
|
|
|
29
|
+* M23 - Select SD file (M23 filename.g)
|
|
|
30
|
+* M24 - Start/resume SD print
|
|
|
31
|
+* M25 - Pause SD print
|
|
|
32
|
+* M26 - Set SD position in bytes (M26 S12345)
|
|
|
33
|
+* M27 - Report SD print status
|
|
|
34
|
+* M28 - Start SD write (M28 filename.g)
|
|
|
35
|
+* M29 - Stop SD write
|
|
|
36
|
+* M30 - Delete file from SD (M30 filename.g)
|
|
|
37
|
+* M31 - Output time since last M109 or SD card start to serial
|
|
|
38
|
+* M32 - Select file and start SD print (Can be used when printing from SD card)
|
|
|
39
|
+* M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used.
|
|
|
40
|
+* M80 - Turn on Power Supply
|
|
|
41
|
+* M81 - Turn off Power Supply
|
|
|
42
|
+* M82 - Set E codes absolute (default)
|
|
|
43
|
+* M83 - Set E codes relative while in Absolute Coordinates (G90) mode
|
|
|
44
|
+* M84 - Disable steppers until next move, or use S<seconds> to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout.
|
|
|
45
|
+* M85 - Set inactivity shutdown timer with parameter S<seconds>. To disable set zero (default)
|
|
|
46
|
+* M92 - Set axis_steps_per_unit - same syntax as G92
|
|
|
47
|
+* M104 - Set extruder target temp
|
|
|
48
|
+* M105 - Read current temp
|
|
|
49
|
+* M106 - Fan on
|
|
|
50
|
+* M107 - Fan off
|
|
|
51
|
+* M109 - Sxxx Wait for extruder current temp to reach target temp. Waits only when heating
|
|
|
52
|
+* Rxxx Wait for extruder current temp to reach target temp. Waits when heating and cooling
|
|
|
53
|
+* M112 - Emergency stop
|
|
|
54
|
+* M114 - Output current position to serial port
|
|
|
55
|
+* M115 - Capabilities string
|
|
|
56
|
+* M117 - display message
|
|
|
57
|
+* M119 - Output Endstop status to serial port
|
|
|
58
|
+* M126 - Solenoid Air Valve Open (BariCUDA support by jmil)
|
|
|
59
|
+* M127 - Solenoid Air Valve Closed (BariCUDA vent to atmospheric pressure by jmil)
|
|
|
60
|
+* M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil)
|
|
|
61
|
+* M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil)
|
|
|
62
|
+* M140 - Set bed target temp
|
|
|
63
|
+* M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating
|
|
|
64
|
+* Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling
|
|
|
65
|
+* M200 D<millimeters>- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).
|
|
|
66
|
+* M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
|
|
|
67
|
+* M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!!
|
|
|
68
|
+* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
|
|
|
69
|
+* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
|
|
|
70
|
+* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
|
|
|
71
|
+* M206 - set additional homeing offset
|
|
|
72
|
+* M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting
|
|
|
73
|
+* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min]
|
|
|
74
|
+* M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
|
|
|
75
|
+* M218 - set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
|
|
|
76
|
+* M220 S<factor in percent>- set speed factor override percentage
|
|
|
77
|
+* M221 S<factor in percent>- set extrude factor override percentage
|
|
|
78
|
+* M240 - Trigger a camera to take a photograph
|
|
|
79
|
+* M280 - Position an RC Servo P<index> S<angle/microseconds>, ommit S to report back current angle
|
|
|
80
|
+* M300 - Play beepsound S<frequency Hz> P<duration ms>
|
|
|
81
|
+* M301 - Set PID parameters P I and D
|
|
|
82
|
+* M302 - Allow cold extrudes
|
|
|
83
|
+* M303 - PID relay autotune S<temperature> sets the target temperature. (default target temperature = 150C)
|
|
|
84
|
+* M304 - Set bed PID parameters P I and D
|
|
|
85
|
+* M400 - Finish all moves
|
|
|
86
|
+* M401 - Lower z-probe if present
|
|
|
87
|
+* M402 - Raise z-probe if present
|
|
|
88
|
+* M404 - N<dia in mm> Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters
|
|
|
89
|
+* M405 - Turn on Filament Sensor extrusion control. Optional D<delay in cm> to set delay in centimeters between sensor and extruder
|
|
|
90
|
+* M406 - Turn off Filament Sensor extrusion control
|
|
|
91
|
+* M407 - Displays measured filament diameter
|
|
|
92
|
+* M500 - stores paramters in EEPROM
|
|
|
93
|
+* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
|
|
94
|
+* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
|
|
95
|
+* M503 - print the current settings (from memory not from eeprom)
|
|
|
96
|
+* M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
|
|
|
97
|
+* M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
|
|
98
|
+* M907 - Set digital trimpot motor current using axis codes.
|
|
|
99
|
+* M908 - Control digital trimpot directly.
|
|
|
100
|
+* M350 - Set microstepping mode.
|
|
|
101
|
+* M351 - Toggle MS1 MS2 pins directly.
|
|
|
102
|
+* M928 - Start SD logging (M928 filename.g) - ended by M29
|
|
|
103
|
+* M999 - Restart after being stopped by error
|
Steffen Vogel
10 years ago