- update example configs

 - rename to PROBING_HEATERS_OFF
 - move heater pausing functionality into thermalManager
   - add variables, pause(), ispaused(), other functions
 - add fan pausing functionality -> PROBING_FANS_OFF
 - add probing_pause() wrapper
 - move pausing into do_homing_move() and do_probe_move() to minimize quiet time and so other probe types can benefit
 - example configs

This is what I did yesterday:

- basicly gave the tests more comprehensive names; put all the
declarations at the top; got rid of the magic negative C-value (renamed
to P + A, O, T)

- "cos(RADIANS(180 + 30 * axis)) * (1 + circles * 0.1 * ((zig_zag) ? 1 :
-1)) * delta_calibration_radius" compiles wrong is zig_zag statement is
without brackets

- DELTA_TOWER_ANGLE_TRIM reset to 3 values (the calcs use the 3th value
to normalize will not compile otherwise)

-Wrote 3 dummies to keep EEPROM lenght the same

-Reset the configs to the 'original' with autocal + menu disabled (but
can be enabled of course)

The Configuration.h file entries for BL-Touch have been updated to:
```cpp
//#define BLTOUCH
//#define BLTOUCH_DELAY 375      // (ms) Enable and increase if needed
//#define BLTOUCH_HEATERS_OFF // if defined the printer's heaters are
turned off during probe event
```

More consistent with M665 where C-value is allowed as well, then
normalized

and getting rid off verbose level 3 and configuration_adv settings

- Making M665 compatible with repetier (see
http://reprap.org/wiki/G_code#M665:_Set_delta_configuration)

- M665 B also sets the radius for manual calibration menu

- Converting tower ajustment definitions to arrays - tower angle
corrections compatible with Esher 3D wizzard

- Only tower angles need to be adjustable with M665 and stored to EEPROM
- tower radius and diag rod can be adjusted in the FW only with #define

Firmware was forgetting the z_fade_height in Planner, set by M420 Z<f>,
after each reset or loading settings from EEPROM. Added the float
z_fade_height to EEPROM-Storage, now remembers the value.

DAC_STEPPER_DFLT wasn't changed to DAC_MOTOR_CURRENT_DEFAULT in all
places on PR #6124

# This is the 1st commit message:

MCP4728 consistency & fix ultralcd.cpp

The MCP4728 DAC controls the stepper motor current strenth on the
PRINTRBOARD Rev F and RIGIDBOARD V2 boards.

PR #5792 on 9 FEB 2017 implemented default drive percentages but only on
the RIGIDBOARD V2.

This change moves the default settings to Configuration_adv.h.

Also, ultralcd.cpp won't compile because of a type def conflict.
Changed it to match the one in stepper_dac.cpp

===========================================================

reword stepper curent section for clarity

===========================================================

change name & improve comments

===========================================================

changed name from A4JP to SCOOVO_X9H per PR #6139

# This is the commit message #2:

fix typo

==============================================

clarified BLTouch calculation & changed comment delimitters/flags

I found it hard to pickout the various sections in this area so I
changed most comments from // style to /** ... */

Made the BLTouch calculation simpler and clarified the units of measure
for the result.

============================================

add changes to example configurations

============================================

add TinyBoy2 to this PR & add BLTouch Delay

The offset for Z_DUAL_ENDSTOP (z_endstop_adj) is already in Marlin.
This PR just makes it a configuration item.

z_endstop_adj is initialized in two places so both had to be modified.