marlin

Commit Graph

Tekijä	SHA1	Viesti	Päivämäärä
Bernhard	1d06b10962	Added a feature to have filament change by gcode or display trigger. [default off for now] syntax: M600 X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] if enabled, after a M600, the printer will retract by E, lift by Z, move to XY, retract even more filament. Oh, and it will display "remove filament" and beep like crazy. You are then supposed to insert a new filament (other color, e.g.) and click the display to continue. After having the nozzle cleaned manually, aided by the disabled e-steppers. After clicking, the printer will then go back the whole shebang, and continue printing with a fancy new color.	11 vuotta sitten
daid303	0f3f5d083d	Minor cleanup of the new FAN_KICKSTART code. #334	12 vuotta sitten
Kevin O'Connor	3d91bd486c	Add "kick fan" feature - briefly run fan at full speed on start. Add a feature to run the cooling fan at full speed for a small period (default 100ms) when first starting the fan. Some fans wont reliably start spinning at low power, and many fans have issue with the PWM at low power. However, once the fan starts spinning it can reliably be set to a wide range of PWM values.	12 vuotta sitten
daid303	921273baa0	Added optional feature to stop printing when an endstop is hit. Made the Z display on the LCD in 3.2 format instead of 3.1. Added LCD message when and endstop is hit.	12 vuotta sitten
Nicolas Rossi	f3c1fc70a9	Power signal control definitions for ATX and others	12 vuotta sitten
Johann Rocholl	1f45cb0a51	Fix typo in MANUAL_HOME_POSITION (plural S missing) and improve comments.	12 vuotta sitten
daid303	587154c01b	Fix the WATCHPERIOD implementation. It did not work correctly in a multi extruder setup, it did not work after 32 seconds after startup (int16 used as millies timestamp). And it did not work if you gave an M104 or M109 when the target was already around the target setpoint. So on average, it did not work at all. The new implementation should be robust in detecting a failure to heat up.	12 vuotta sitten
daid303	f6ff0ab767	signed/unsigned fixes.	12 vuotta sitten
daid303	b6ff45254e	Better explain the watchdog "problem" and rename the config define so it explains that the feature belongs to the watchdog.	12 vuotta sitten
daid303	7e348fcb5f	By mistake enabled the watchdog by default. This should be off by default.	12 vuotta sitten
daid303	06b58a9c4f	First cleanup. Moved all code to cpp files, so there are no dependencies on pde files. And no more odd requirement to cat files together. (Still need to fix the Makefile). Also cleaned up some defines and made defines upper case as by C coding conventions.	12 vuotta sitten
Mark Finn	04631d2250	cleanup for pull	12 vuotta sitten
ZetaPhoenix	c6caa45ae2	Limit Switch locations based on MIN/MAX limits and homing direction fixes #246 Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined. Relocated code based on feedback.	12 vuotta sitten
tonokip	1c1fddc7ac	Added support for the Rambo reprap electronics board. Added Mcodes to set motor current and microstepping pins.	12 vuotta sitten
Enchiridion	50cde90324	Added support for dual Z axis stepper drivers	12 vuotta sitten
daid	12de8fff81	Support step motor controllers with active low step pins.	12 vuotta sitten
Bernhard	0c123950e9	__ header file replace	12 vuotta sitten
Bernhard	bf077125b9	added firmware retract. disabled by default	12 vuotta sitten
Erik van der Zalm	67cf105bc6	Fixed AUTOTEMP (M109 S215 B260 F1 starts autotemp) Changed SLOWDOWN. IF this does not work ok OLD_SLOWDOWN is the old algo.	12 vuotta sitten
Erik van der Zalm	4ca2f336f0	Changed default MINIMUM_PLANNER_SPEED -> 0.05 Fixed small bug in arcs M105 prints now actual_temp/target_temp	12 vuotta sitten
Bernhard	1532200435	found error in filenames. One array was too short. This had nothing to do with long filenames, other than if they were 12 characters exactly, which could only happen if the extension and the text before were filled completely	12 vuotta sitten
Erik van der Zalm	87ff2f8867	Added CONTROLLERFAN. (Controlling a fan to cool down the steppper drivers)	12 vuotta sitten
Erik van der Zalm	c6f2ec3c82	remove stop_heating_wait	12 vuotta sitten
Erik van der Zalm	018c567abf	Moved SLOWDOWN function. (jetty840) Included AD595 calibration options. (daid)	12 vuotta sitten
Blair Thompson	d9f2f509d5	Added new menu items under the prepare submenu. Instead of a single pre-heat, now there is pre-heat ABS and PLA options Added defines to the configuration file to adjust preheat temperatures for both	12 vuotta sitten
Erik van der Zalm	8816ef1c64	Small fixes after merge	12 vuotta sitten
Erik van der Zalm	b447815de5	removed unused HEATING_EARLY_FINISH_DEG_OFFSET Simplified stepper inactive time	12 vuotta sitten
Erik van der Zalm	13e185d330	removed unused HEATING_EARLY_FINISH_DEG_OFFSET Simplified stepper inactive time	12 vuotta sitten
Erik van der Zalm	5113513cb2	RC 1	12 vuotta sitten
Erik van der Zalm	d8a0c6450f	Split the configuration file in two parts. One for common settings. One for advanced settings.	12 vuotta sitten

32 Commitit (9f2862ce489271f0e5dbd00f06e4e9bfb670af26)