/** * Marlin 3D Printer Firmware * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #include "env_validate.h" #if HOTENDS > 3 || E_STEPPERS > 3 #error "Tronxy V10 supports up to 3 hotends / E steppers." #endif #define BOARD_INFO_NAME "Tronxy V10" #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME #define STEP_TIMER 6 #define TEMP_TIMER 14 // // Servos // //#define SERVO0_PIN PB10 // // EEPROM // #if NO_EEPROM_SELECTED #undef NO_EEPROM_SELECTED #if TRONXY_UI > 0 #define EEPROM_AT24CXX #else #define FLASH_EEPROM_EMULATION #endif #endif #if ENABLED(FLASH_EEPROM_EMULATION) // SoC Flash (framework-arduinoststm32-maple/STM32F1/libraries/EEPROM/EEPROM.h) #define EEPROM_START_ADDRESS (0x8000000UL + (512 * 1024) - 2 * EEPROM_PAGE_SIZE) #define EEPROM_PAGE_SIZE (0x800U) // 2KB, but will use 2x more (4KB) #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE #else #if ENABLED(EEPROM_AT24CXX) #define AT24CXX_SCL PB8 #define AT24CXX_SDA PB9 #define AT24CXX_WP PB7 #else #define I2C_EEPROM // AT24C32 #endif #define MARLIN_EEPROM_SIZE 0x1000 // 4K #endif // // SPI Flash // //#define SPI_FLASH #if ENABLED(SPI_FLASH) #define SPI_FLASH_SIZE 0x200000 // 2MB #define W25QXX_CS_PIN PG15 // SPI2 #define W25QXX_MOSI_PIN PB5 #define W25QXX_MISO_PIN PB4 #define W25QXX_SCK_PIN PB3 #endif // // Limit Switches // #define X_MIN_PIN PC15 #define X_MAX_PIN PB0 #define Y_STOP_PIN PC14 #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN PE3 #endif #if ENABLED(DUAL_Z_ENDSTOP_PROBE) #if NUM_Z_STEPPERS > 1 && Z_HOME_TO_MAX // Swap Z1/Z2 for dual Z with max homing #define Z_MIN_PIN PF11 #define Z_MAX_PIN PC13 #else #define Z_MIN_PIN PC13 #define Z_MAX_PIN PF11 #endif #else #ifndef Z_STOP_PIN #define Z_STOP_PIN PC13 #endif #endif // // Filament Sensors // #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN PE6 // MT_DET #endif #ifndef FIL_RUNOUT2_PIN #define FIL_RUNOUT2_PIN PF12 #endif // // Steppers // #define X_ENABLE_PIN PF0 #define X_STEP_PIN PE5 #define X_DIR_PIN PF1 #define Y_ENABLE_PIN PF5 #define Y_STEP_PIN PF9 #define Y_DIR_PIN PF3 #define Z_ENABLE_PIN PA5 #define Z_STEP_PIN PA6 #define Z_DIR_PIN PF15 #define E0_ENABLE_PIN PF14 #define E0_STEP_PIN PB1 #define E0_DIR_PIN PF13 #define E1_ENABLE_PIN PG5 #define E1_STEP_PIN PD12 #define E1_DIR_PIN PG4 #define E2_ENABLE_PIN PF7 #define E2_STEP_PIN PF6 #define E2_DIR_PIN PF4 // // Temperature Sensors // #define TEMP_0_PIN PC3 // TH1 #define TEMP_BED_PIN PC2 // TB1 // // Heaters / Fans // #define HEATER_0_PIN PG7 // HEATER1 #define HEATER_BED_PIN PE2 // HOT BED //#define HEATER_BED_INVERTING true #define FAN_PIN PG0 // FAN0 #define FAN1_PIN PB6 // FAN1 #define FAN2_PIN PG9 // FAN2 #define FAN3_PIN PF10 // FAN3 #define CONTROLLER_FAN_PIN PD7 // BOARD FAN #define FAN_SOFT_PWM // // Laser / Spindle // #if HAS_CUTTER #define SPINDLE_LASER_ENA_PIN PB11 // wifi:TX #if ENABLED(SPINDLE_LASER_USE_PWM) #define SPINDLE_LASER_PWM_PIN PB10 // wifi:RX-TIM2_CH3 // The PWM pin definition const PinMap PinMap_PWM[] in PeripheralPins.c must be compounded here // See PWM_PIN(x) definition for details #endif #endif // // Misc // #define BEEPER_PIN PA8 //#define LED_PIN PG10 #define PS_ON_PIN PG10 // Temporarily switch the machine with LED simulation #if ENABLED(TRONXY_BACKUP_POWER) #define POWER_LOSS_PIN PF11 // Configure as drop-down input #else #define POWER_LOSS_PIN PE1 // Output of LM393 comparator, configured as pullup #endif //#define POWER_LM393_PIN PE0 // +V for the LM393 comparator, configured as output high #if ENABLED(TFT_TRONXY_X5SA) #error "TFT_TRONXY_X5SA is not yet supported." #endif #if 0 // // TFT with FSMC interface // #if HAS_FSMC_TFT #define TFT_RESET_PIN PB12 #define TFT_BACKLIGHT_PIN PG8 #define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT #define FSMC_DMA_DEV DMA2 #define FSMC_DMA_CHANNEL DMA_CH5 #define TFT_CS_PIN PG12 #define TFT_RS_PIN PG2 //#define TFT_WIDTH 480 //#define TFT_HEIGHT 320 //#define TFT_PIXEL_OFFSET_X 48 //#define TFT_PIXEL_OFFSET_Y 32 //#define TFT_DRIVER ILI9488 //#define TFT_BUFFER_SIZE 14400 #if NEED_TOUCH_PINS #define TOUCH_CS_PIN PD11 // SPI1_NSS #define TOUCH_SCK_PIN PB13 // SPI1_SCK #define TOUCH_MISO_PIN PB14 // SPI1_MISO #define TOUCH_MOSI_PIN PB15 // SPI1_MOSI #endif #if (LCD_CHIP_INDEX == 1 && (TRONXY_UI == 1 || TRONXY_UI == 2)) || LCD_CHIP_INDEX == 3 #define TOUCH_CALIBRATION_X -17181 #define TOUCH_CALIBRATION_Y 11434 #define TOUCH_OFFSET_X 501 #define TOUCH_OFFSET_Y -9 #elif LCD_CHIP_INDEX == 1 && TRONXY_UI == 4 #define TOUCH_CALIBRATION_X 11166 #define TOUCH_CALIBRATION_Y 17162 #define TOUCH_OFFSET_X -10 #define TOUCH_OFFSET_Y -16 #elif LCD_CHIP_INDEX == 4 && TRONXY_UI == 3 //#define TOUCH_CALIBRATION_X 8781 //#define TOUCH_CALIBRATION_Y 11773 //#define TOUCH_OFFSET_X -17 //#define TOUCH_OFFSET_Y -16 // Upside-down #define TOUCH_CALIBRATION_X -8553 #define TOUCH_CALIBRATION_Y -11667 #define TOUCH_OFFSET_X 253 #define TOUCH_OFFSET_Y 331 #elif LCD_CHIP_INDEX == 2 #define TOUCH_CALIBRATION_X 17184 #define TOUCH_CALIBRATION_Y 10604 #define TOUCH_OFFSET_X -31 #define TOUCH_OFFSET_Y -29 #endif #endif #endif // // SD Card // #define SDIO_SUPPORT #define SD_DETECT_PIN -1 // PF0, but not connected #define SDIO_CLOCK 4500000 #define SDIO_READ_RETRIES 16 #define SDIO_D0_PIN PC8 #define SDIO_D1_PIN PC9 #define SDIO_D2_PIN PC10 #define SDIO_D3_PIN PC11 #define SDIO_CK_PIN PC12 #define SDIO_CMD_PIN PD2