/** * Marlin 3D Printer Firmware * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once //#define BOARD_CUSTOM_BUILD_FLAGS -DTONE_CHANNEL=4 -DTONE_TIMER=4 -DTIMER_TONE=4 #ifndef BOARD_INFO_NAME #define BOARD_INFO_NAME "BTT SKR Mini E3 V3.0" #endif #define USES_DIAG_JUMPERS // Ignore temp readings during development. //#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 #define LED_PIN PD8 // Onboard I2C EEPROM #if EITHER(NO_EEPROM_SELECTED, I2C_EEPROM) #undef NO_EEPROM_SELECTED #define I2C_EEPROM #define SOFT_I2C_EEPROM // Force the use of Software I2C #define I2C_SCL_PIN PB6 #define I2C_SDA_PIN PB7 #define MARLIN_EEPROM_SIZE 0x1000 // 4K #endif // // Servos // #define SERVO0_PIN PA1 // SERVOS // // Limit Switches // #define X_STOP_PIN PC0 // X-STOP #define Y_STOP_PIN PC1 // Y-STOP #define Z_STOP_PIN PC2 // Z-STOP // // Z Probe must be this pin // #define Z_MIN_PROBE_PIN PC14 // PROBE // // Filament Runout Sensor // #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN PC15 // E0-STOP #endif // // Power-loss Detection // #ifndef POWER_LOSS_PIN #define POWER_LOSS_PIN PC12 // Power Loss Detection: PWR-DET #endif #ifndef PS_ON_PIN #define PS_ON_PIN PC13 // Power Supply Control #endif // // Steppers // #define X_ENABLE_PIN PB14 #define X_STEP_PIN PB13 #define X_DIR_PIN PB12 #define Y_ENABLE_PIN PB11 #define Y_STEP_PIN PB10 #define Y_DIR_PIN PB2 #define Z_ENABLE_PIN PB1 #define Z_STEP_PIN PB0 #define Z_DIR_PIN PC5 #define E0_ENABLE_PIN PD1 #define E0_STEP_PIN PB3 #define E0_DIR_PIN PB4 #if HAS_TMC_UART /** * TMC220x stepper drivers * Hardware serial communication ports */ #define X_HARDWARE_SERIAL MSerial4 #define Y_HARDWARE_SERIAL MSerial4 #define Z_HARDWARE_SERIAL MSerial4 #define E0_HARDWARE_SERIAL MSerial4 // Default TMC slave addresses #ifndef X_SLAVE_ADDRESS #define X_SLAVE_ADDRESS 0 #endif #ifndef Y_SLAVE_ADDRESS #define Y_SLAVE_ADDRESS 2 #endif #ifndef Z_SLAVE_ADDRESS #define Z_SLAVE_ADDRESS 1 #endif #ifndef E0_SLAVE_ADDRESS #define E0_SLAVE_ADDRESS 3 #endif #endif // // Temperature Sensors // #define TEMP_0_PIN PA0 // Analog Input "TH0" #define TEMP_BED_PIN PC4 // Analog Input "TB0" // // Heaters / Fans // #define HEATER_0_PIN PC8 // "HE" #define HEATER_BED_PIN PC9 // "HB" #define FAN_PIN PC6 // "FAN0" #define FAN1_PIN PC7 // "FAN1" #define FAN2_PIN PB15 // "FAN2" /** * SKR Mini E3 V3.0 * ------ * (BEEPER) PB5 | 1 2 | PA15 (BTN_ENC) * (BTN_EN1) PA9 | 3 4 | RESET * (BTN_EN2) PA10 5 6 | PB9 (LCD_D4) * (LCD_RS) PB8 | 7 8 | PD6 (LCD_EN) * GND | 9 10 | 5V * ------ * EXP1 */ #define EXP1_01_PIN PB5 #define EXP1_02_PIN PA15 #define EXP1_03_PIN PA9 #define EXP1_04_PIN -1 #define EXP1_05_PIN PA10 #define EXP1_06_PIN PB9 #define EXP1_07_PIN PB8 #define EXP1_08_PIN PD6 #define EXP1_09_PIN -1 #define EXP1_10_PIN -1 #if HAS_DWIN_E3V2 || IS_DWIN_MARLINUI /** * ------ ------ ------ * (ENT) | 1 2 | (BEEP) |10 9 | |10 9 | * (RX) | 3 4 | (RX) | 8 7 | (TX) RX | 8 7 | TX * (TX) 5 6 | (ENT) 6 5 | (BEEP) ENT | 6 5 | BEEP * (B) | 7 8 | (A) (B) | 4 3 | (A) B | 4 3 | A * GND | 9 10 | (VCC) GND | 2 1 | VCC GND | 2 1 | VCC * ------ ------ ------ * EXP1 DWIN DWIN (plug) * * All pins are labeled as printed on DWIN PCB. Connect TX-TX, A-A and so on. */ #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING #error "CAUTION! DWIN_CREALITY_LCD requires a custom cable, see diagram above this line. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)" #endif #define BEEPER_PIN EXP1_02_PIN #define BTN_EN1 EXP1_08_PIN #define BTN_EN2 EXP1_07_PIN #define BTN_ENC EXP1_01_PIN #elif HAS_WIRED_LCD #if ENABLED(SKR_MINI_SCREEN_ADAPTER) /** https://github.com/VoronDesign/Voron-Hardware/tree/master/SKR-Mini_Screen_Adaptor/SRK%20Mini%20E3%20V3.0 * * SKR Mini E3 V3.0 SKR Mini Screen Adaptor * ------ ------ * 5V | 1 2 | GND MISO | 1 2 | SCK * CS | 3 4 | SCK (EN1) PA10 | 3 4 | -- * MOSI | 5 6 | MISO (EN2) PA9 5 6 | MOSI * 3V3 | 7 8 | GND -- | 7 8 | -- * ------ GND | 9 10| RESET (Kill) * SPI ------ * EXP2 * * ------ ------ * PB5 | 1 2 | PA15 -- | 1 2 | PB5 (BTN_ENC) * PA9 | 3 4 | RESET (LCD CS) PB8 | 3 4 | PD6 (LCD_A0) * PA10 5 6 | PB9 (RESET) PB9 5 6 | PA15 (DIN) * PB8 | 7 8 | PD6 -- | 7 8 | -- * GND | 9 10| 5V GND | 9 10| 5V * ------ ------ * EXP1 EXP1 */ #if ENABLED(FYSETC_MINI_12864_2_1) #define BTN_ENC EXP1_01_PIN #define BTN_EN1 EXP1_03_PIN #define BTN_EN2 EXP1_05_PIN #define BEEPER_PIN -1 #define LCD_RESET_PIN EXP1_06_PIN #define DOGLCD_CS EXP1_07_PIN #define DOGLCD_A0 EXP1_08_PIN #define DOGLCD_SCK PA5 #define DOGLCD_MOSI PA7 #define FORCE_SOFT_SPI #define LCD_BACKLIGHT_PIN -1 #define NEOPIXEL_PIN EXP1_02_PIN #else #error "Only CR10_FYSETC_MINI_12864_2_1 and compatibles are currently supported on the BIGTREE_SKR_MINI_E3 with SKR_MINI_SCREEN_ADAPTER" #endif #else #if ENABLED(CR10_STOCKDISPLAY) #define BEEPER_PIN EXP1_01_PIN #define BTN_ENC EXP1_02_PIN #define BTN_EN1 EXP1_03_PIN #define BTN_EN2 EXP1_05_PIN #define LCD_PINS_RS EXP1_07_PIN #define LCD_PINS_ENABLE EXP1_08_PIN #define LCD_PINS_D4 EXP1_06_PIN #elif ENABLED(ZONESTAR_LCD) // ANET A8 LCD Controller - Must convert to 3.3V - CONNECTING TO 5V WILL DAMAGE THE BOARD! #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING #error "CAUTION! ZONESTAR_LCD requires wiring modifications. See 'pins_BTT_SKR_MINI_E3_common.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)" #endif #define LCD_PINS_RS EXP1_06_PIN #define LCD_PINS_ENABLE EXP1_02_PIN #define LCD_PINS_D4 EXP1_07_PIN #define LCD_PINS_D5 EXP1_05_PIN #define LCD_PINS_D6 EXP1_03_PIN #define LCD_PINS_D7 EXP1_01_PIN #define ADC_KEYPAD_PIN PA1 // Repurpose servo pin for ADC - CONNECTING TO 5V WILL DAMAGE THE BOARD! #elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY) #define BTN_ENC EXP1_02_PIN #define BTN_EN1 EXP1_03_PIN #define BTN_EN2 EXP1_05_PIN #define DOGLCD_CS EXP1_07_PIN #define DOGLCD_A0 EXP1_06_PIN #define DOGLCD_SCK EXP1_01_PIN #define DOGLCD_MOSI EXP1_08_PIN #define FORCE_SOFT_SPI #define LCD_BACKLIGHT_PIN -1 #elif IS_TFTGLCD_PANEL #if ENABLED(TFTGLCD_PANEL_SPI) #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING #error "CAUTION! TFTGLCD_PANEL_SPI requires wiring modifications. See 'pins_BTT_SKR_MINI_E3_common.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)" #endif /** * TFTGLCD_PANEL_SPI display pinout * * Board Display * ------ ------ * (BEEPER) PB6 | 1 2 | PB5 (SD_DET) 5V |10 9 | GND * RESET | 3 4 | PA9 (MOD_RESET) -- | 8 7 | (SD_DET) * PB9 5 6 | PA10 (SD_CS) (MOSI) | 6 5 | -- * PB7 | 7 8 | PB8 (LCD_CS) (SD_CS) | 4 3 | (LCD_CS) * GND | 9 10 | 5V (SCK) | 2 1 | (MISO) * ------ ------ * EXP1 EXP1 * * Needs custom cable: * * Board Display * * EXP1-10 ----------- EXP1-10 5V * EXP1-9 ------------ EXP1-9 GND * SPI1-4 ------------ EXP1-6 MOSI * EXP1-7 ------------ n/c * SPI1-3 ------------ EXP1-2 SCK * EXP1-5 ------------ EXP1-4 SD_CS * EXP1-4 ------------ n/c * EXP1-3 ------------ EXP1-3 LCD_CS * SPI1-1 ------------ EXP1-1 MISO * EXP1-1 ------------ EXP1-7 SD_DET */ #define TFTGLCD_CS EXP1_03_PIN #endif #elif ENABLED(FYSETC_MINI_12864_2_1) #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING #error "CAUTION! FYSETC_MINI_12864_2_1 and clones require wiring modifications. See 'pins_BTT_SKR_MINI_E3_V3_0.h' for details. Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning." #endif /** * * Board Display * ------ ------ * (EN2) PB5 | 1 2 | PA15(BTN_ENC) 5V |10 9 | GND * (LCD_CS) PA9 | 3 4 | RST (RESET) -- | 8 7 | -- * (LCD_A0) PA10 5 6 | PB9 (EN1) (DIN) | 6 5 (RESET) * (LCD_SCK)PB8 | 7 8 | PD6 (MOSI) (LCD_A0) | 4 3 | (LCD_CS) * GND | 9 10 | 5V (BTN_ENC) | 2 1 | -- * ------ ------ * EXP1 EXP1 * * ------ * -- |10 9 | -- * --- (RESET) | 8 7 | -- * | 3 | (MOSI) | 6 5 (EN2) * | 2 | (DIN) -- | 4 3 | (EN1) * | 1 | (LCD_SCK)| 2 1 | -- * --- ------ * Neopixel EXP2 * * Needs custom cable. Connect EN2-EN2, LCD_CS-LCD_CS and so on. * * Check the index/notch position twice!!! * On BTT boards pins from IDC10 connector are numbered in unusual order. */ #define BTN_ENC EXP1_02_PIN #define BTN_EN1 EXP1_06_PIN #define BTN_EN2 EXP1_01_PIN #define BEEPER_PIN -1 #define DOGLCD_CS EXP1_03_PIN #define DOGLCD_A0 EXP1_05_PIN #define DOGLCD_SCK EXP1_07_PIN #define DOGLCD_MOSI EXP1_08_PIN #define FORCE_SOFT_SPI #define LCD_BACKLIGHT_PIN -1 #else #error "Only CR10_STOCKDISPLAY, ZONESTAR_LCD, ENDER2_STOCKDISPLAY, MKS_MINI_12864, FYSETC_MINI_12864_2_1, and TFTGLCD_PANEL_(SPI|I2C) are currently supported on the BIGTREE_SKR_MINI_E3." #endif #endif // SKR_MINI_SCREEN_ADAPTER #endif // HAS_WIRED_LCD #if BOTH(TOUCH_UI_FTDI_EVE, LCD_FYSETC_TFT81050) #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING #error "CAUTION! LCD_FYSETC_TFT81050 requires wiring modifications. See 'pins_BTT_SKR_MINI_E3_common.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)" #endif /** * FYSETC TFT TFT81050 display pinout * * Board Display * ------ ------ * (SD_DET) PB5 | 1 2 | PB6 (BEEPER) 5V |10 9 | GND * (MOD_RESET) PA9 | 3 4 | RESET (RESET) | 8 7 | (SD_DET) * (SD_CS) PA10 5 6 | PB9 (FREE) (MOSI) | 6 5 | (LCD_CS) * (LCD_CS) PB8 | 7 8 | PB7 (FREE) (SD_CS) | 4 3 | (MOD_RESET) * 5V | 9 10 | GND (SCK) | 2 1 | (MISO) * ------ ------ * EXP1 EXP1 * * Needs custom cable: * * Board Adapter Display * ---------------------------------- * EXP1-10 ----------- EXP1-10 5V * EXP1-9 ------------ EXP1-9 GND * SPI1-4 ------------ EXP1-6 MOSI * EXP1-7 ------------ EXP1-5 LCD_CS * SPI1-3 ------------ EXP1-2 SCK * EXP1-5 ------------ EXP1-4 SD_CS * EXP1-4 ------------ EXP1-8 RESET * EXP1-3 ------------ EXP1-3 MOD_RST * SPI1-1 ------------ EXP1-1 MISO * EXP1-1 ------------ EXP1-7 SD_DET */ #define CLCD_SPI_BUS 1 // SPI1 connector #define BEEPER_PIN EXP1_02_PIN #define CLCD_MOD_RESET EXP1_03_PIN #define CLCD_SPI_CS EXP1_07_PIN #endif // TOUCH_UI_FTDI_EVE && LCD_FYSETC_TFT81050 // // SD Support // #ifndef SDCARD_CONNECTION #define SDCARD_CONNECTION ONBOARD #endif #if SD_CONNECTION_IS(ONBOARD) #define SD_DETECT_PIN PC3 #elif SD_CONNECTION_IS(LCD) && (BOTH(TOUCH_UI_FTDI_EVE, LCD_FYSETC_TFT81050) || IS_TFTGLCD_PANEL) #define SD_DETECT_PIN EXP1_01_PIN #define SD_SS_PIN EXP1_05_PIN #elif SD_CONNECTION_IS(CUSTOM_CABLE) #error "SD CUSTOM_CABLE is not compatible with SKR Mini E3." #endif #define ONBOARD_SPI_DEVICE 1 // SPI1 -> used only by HAL/STM32F1... #define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card #define ENABLE_SPI1 #define SDSS ONBOARD_SD_CS_PIN #define SD_SS_PIN ONBOARD_SD_CS_PIN #define SD_SCK_PIN PA5 #define SD_MISO_PIN PA6 #define SD_MOSI_PIN PA7 // // Default NEOPIXEL_PIN // #ifndef NEOPIXEL_PIN #define NEOPIXEL_PIN PA8 // LED driving pin #endif