123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <https://www.gnu.org/licenses/>.
- *
- */
-
- #include "../../inc/MarlinConfig.h"
-
- #if ENABLED(DELTA_AUTO_CALIBRATION)
-
- #include "../gcode.h"
- #include "../../module/delta.h"
- #include "../../module/motion.h"
- #include "../../module/stepper.h"
- #include "../../module/endstops.h"
- #include "../../lcd/ultralcd.h"
-
- #if HAS_BED_PROBE
- #include "../../module/probe.h"
- #endif
-
- #if HAS_MULTI_HOTEND
- #include "../../module/tool_change.h"
- #endif
-
- #if HAS_LEVELING
- #include "../../feature/bedlevel/bedlevel.h"
- #endif
-
- constexpr uint8_t _7P_STEP = 1, // 7-point step - to change number of calibration points
- _4P_STEP = _7P_STEP * 2, // 4-point step
- NPP = _7P_STEP * 6; // number of calibration points on the radius
- enum CalEnum : char { // the 7 main calibration points - add definitions if needed
- CEN = 0,
- __A = 1,
- _AB = __A + _7P_STEP,
- __B = _AB + _7P_STEP,
- _BC = __B + _7P_STEP,
- __C = _BC + _7P_STEP,
- _CA = __C + _7P_STEP,
- };
-
- #define LOOP_CAL_PT(VAR, S, N) for (uint8_t VAR=S; VAR<=NPP; VAR+=N)
- #define F_LOOP_CAL_PT(VAR, S, N) for (float VAR=S; VAR<NPP+0.9999; VAR+=N)
- #define I_LOOP_CAL_PT(VAR, S, N) for (float VAR=S; VAR>CEN+0.9999; VAR-=N)
- #define LOOP_CAL_ALL(VAR) LOOP_CAL_PT(VAR, CEN, 1)
- #define LOOP_CAL_RAD(VAR) LOOP_CAL_PT(VAR, __A, _7P_STEP)
- #define LOOP_CAL_ACT(VAR, _4P, _OP) LOOP_CAL_PT(VAR, _OP ? _AB : __A, _4P ? _4P_STEP : _7P_STEP)
-
- TERN_(HAS_MULTI_HOTEND, const uint8_t old_tool_index = active_extruder);
-
- float lcd_probe_pt(const xy_pos_t &xy);
-
- void ac_home() {
- endstops.enable(true);
- home_delta();
- endstops.not_homing();
- }
-
- void ac_setup(const bool reset_bed) {
- TERN_(HAS_MULTI_HOTEND, tool_change(0, true));
-
- planner.synchronize();
- remember_feedrate_scaling_off();
-
- #if HAS_LEVELING
- if (reset_bed) reset_bed_level(); // After full calibration bed-level data is no longer valid
- #endif
- }
-
- void ac_cleanup(TERN_(HAS_MULTI_HOTEND, const uint8_t old_tool_index)) {
- TERN_(DELTA_HOME_TO_SAFE_ZONE, do_blocking_move_to_z(delta_clip_start_height));
- TERN_(HAS_BED_PROBE, probe.stow());
- restore_feedrate_and_scaling();
- TERN_(HAS_MULTI_HOTEND, tool_change(old_tool_index, true));
- }
-
- void print_signed_float(PGM_P const prefix, const float &f) {
- SERIAL_ECHOPGM(" ");
- serialprintPGM(prefix);
- SERIAL_CHAR(':');
- if (f >= 0) SERIAL_CHAR('+');
- SERIAL_ECHO_F(f, 2);
- }
-
- /**
- * - Print the delta settings
- */
- static void print_calibration_settings(const bool end_stops, const bool tower_angles) {
- SERIAL_ECHOPAIR(".Height:", delta_height);
- if (end_stops) {
- print_signed_float(PSTR("Ex"), delta_endstop_adj.a);
- print_signed_float(PSTR("Ey"), delta_endstop_adj.b);
- print_signed_float(PSTR("Ez"), delta_endstop_adj.c);
- }
- if (end_stops && tower_angles) {
- SERIAL_ECHOPAIR(" Radius:", delta_radius);
- SERIAL_EOL();
- SERIAL_CHAR('.');
- SERIAL_ECHO_SP(13);
- }
- if (tower_angles) {
- print_signed_float(PSTR("Tx"), delta_tower_angle_trim.a);
- print_signed_float(PSTR("Ty"), delta_tower_angle_trim.b);
- print_signed_float(PSTR("Tz"), delta_tower_angle_trim.c);
- }
- if ((!end_stops && tower_angles) || (end_stops && !tower_angles)) { // XOR
- SERIAL_ECHOPAIR(" Radius:", delta_radius);
- }
- SERIAL_EOL();
- }
-
- /**
- * - Print the probe results
- */
- static void print_calibration_results(const float z_pt[NPP + 1], const bool tower_points, const bool opposite_points) {
- SERIAL_ECHOPGM(". ");
- print_signed_float(PSTR("c"), z_pt[CEN]);
- if (tower_points) {
- print_signed_float(PSTR(" x"), z_pt[__A]);
- print_signed_float(PSTR(" y"), z_pt[__B]);
- print_signed_float(PSTR(" z"), z_pt[__C]);
- }
- if (tower_points && opposite_points) {
- SERIAL_EOL();
- SERIAL_CHAR('.');
- SERIAL_ECHO_SP(13);
- }
- if (opposite_points) {
- print_signed_float(PSTR("yz"), z_pt[_BC]);
- print_signed_float(PSTR("zx"), z_pt[_CA]);
- print_signed_float(PSTR("xy"), z_pt[_AB]);
- }
- SERIAL_EOL();
- }
-
- /**
- * - Calculate the standard deviation from the zero plane
- */
- static float std_dev_points(float z_pt[NPP + 1], const bool _0p_cal, const bool _1p_cal, const bool _4p_cal, const bool _4p_opp) {
- if (!_0p_cal) {
- float S2 = sq(z_pt[CEN]);
- int16_t N = 1;
- if (!_1p_cal) { // std dev from zero plane
- LOOP_CAL_ACT(rad, _4p_cal, _4p_opp) {
- S2 += sq(z_pt[rad]);
- N++;
- }
- return LROUND(SQRT(S2 / N) * 1000.0f) / 1000.0f + 0.00001f;
- }
- }
- return 0.00001f;
- }
-
- /**
- * - Probe a point
- */
- static float calibration_probe(const xy_pos_t &xy, const bool stow) {
- #if HAS_BED_PROBE
- return probe.probe_at_point(xy, stow ? PROBE_PT_STOW : PROBE_PT_RAISE, 0, true, false);
- #else
- UNUSED(stow);
- return lcd_probe_pt(xy);
- #endif
- }
-
- /**
- * - Probe a grid
- */
- static bool probe_calibration_points(float z_pt[NPP + 1], const int8_t probe_points, const bool towers_set, const bool stow_after_each) {
- const bool _0p_calibration = probe_points == 0,
- _1p_calibration = probe_points == 1 || probe_points == -1,
- _4p_calibration = probe_points == 2,
- _4p_opposite_points = _4p_calibration && !towers_set,
- _7p_calibration = probe_points >= 3,
- _7p_no_intermediates = probe_points == 3,
- _7p_1_intermediates = probe_points == 4,
- _7p_2_intermediates = probe_points == 5,
- _7p_4_intermediates = probe_points == 6,
- _7p_6_intermediates = probe_points == 7,
- _7p_8_intermediates = probe_points == 8,
- _7p_11_intermediates = probe_points == 9,
- _7p_14_intermediates = probe_points == 10,
- _7p_intermed_points = probe_points >= 4,
- _7p_6_center = probe_points >= 5 && probe_points <= 7,
- _7p_9_center = probe_points >= 8;
-
- LOOP_CAL_ALL(rad) z_pt[rad] = 0.0f;
-
- if (!_0p_calibration) {
-
- const float dcr = delta_calibration_radius();
-
- if (!_7p_no_intermediates && !_7p_4_intermediates && !_7p_11_intermediates) { // probe the center
- const xy_pos_t center{0};
- z_pt[CEN] += calibration_probe(center, stow_after_each);
- if (isnan(z_pt[CEN])) return false;
- }
-
- if (_7p_calibration) { // probe extra center points
- const float start = _7p_9_center ? float(_CA) + _7P_STEP / 3.0f : _7p_6_center ? float(_CA) : float(__C),
- steps = _7p_9_center ? _4P_STEP / 3.0f : _7p_6_center ? _7P_STEP : _4P_STEP;
- I_LOOP_CAL_PT(rad, start, steps) {
- const float a = RADIANS(210 + (360 / NPP) * (rad - 1)),
- r = dcr * 0.1;
- const xy_pos_t vec = { cos(a), sin(a) };
- z_pt[CEN] += calibration_probe(vec * r, stow_after_each);
- if (isnan(z_pt[CEN])) return false;
- }
- z_pt[CEN] /= float(_7p_2_intermediates ? 7 : probe_points);
- }
-
- if (!_1p_calibration) { // probe the radius
- const CalEnum start = _4p_opposite_points ? _AB : __A;
- const float steps = _7p_14_intermediates ? _7P_STEP / 15.0f : // 15r * 6 + 10c = 100
- _7p_11_intermediates ? _7P_STEP / 12.0f : // 12r * 6 + 9c = 81
- _7p_8_intermediates ? _7P_STEP / 9.0f : // 9r * 6 + 10c = 64
- _7p_6_intermediates ? _7P_STEP / 7.0f : // 7r * 6 + 7c = 49
- _7p_4_intermediates ? _7P_STEP / 5.0f : // 5r * 6 + 6c = 36
- _7p_2_intermediates ? _7P_STEP / 3.0f : // 3r * 6 + 7c = 25
- _7p_1_intermediates ? _7P_STEP / 2.0f : // 2r * 6 + 4c = 16
- _7p_no_intermediates ? _7P_STEP : // 1r * 6 + 3c = 9
- _4P_STEP; // .5r * 6 + 1c = 4
- bool zig_zag = true;
- F_LOOP_CAL_PT(rad, start, _7p_9_center ? steps * 3 : steps) {
- const int8_t offset = _7p_9_center ? 2 : 0;
- for (int8_t circle = 0; circle <= offset; circle++) {
- const float a = RADIANS(210 + (360 / NPP) * (rad - 1)),
- r = dcr * (1 - 0.1 * (zig_zag ? offset - circle : circle)),
- interpol = FMOD(rad, 1);
- const xy_pos_t vec = { cos(a), sin(a) };
- const float z_temp = calibration_probe(vec * r, stow_after_each);
- if (isnan(z_temp)) return false;
- // split probe point to neighbouring calibration points
- z_pt[uint8_t(LROUND(rad - interpol + NPP - 1)) % NPP + 1] += z_temp * sq(cos(RADIANS(interpol * 90)));
- z_pt[uint8_t(LROUND(rad - interpol)) % NPP + 1] += z_temp * sq(sin(RADIANS(interpol * 90)));
- }
- zig_zag = !zig_zag;
- }
- if (_7p_intermed_points)
- LOOP_CAL_RAD(rad)
- z_pt[rad] /= _7P_STEP / steps;
-
- do_blocking_move_to_xy(0.0f, 0.0f);
- }
- }
- return true;
- }
-
- /**
- * kinematics routines and auto tune matrix scaling parameters:
- * see https://github.com/LVD-AC/Marlin-AC/tree/1.1.x-AC/documentation for
- * - formulae for approximative forward kinematics in the end-stop displacement matrix
- * - definition of the matrix scaling parameters
- */
- static void reverse_kinematics_probe_points(float z_pt[NPP + 1], abc_float_t mm_at_pt_axis[NPP + 1]) {
- xyz_pos_t pos{0};
-
- const float dcr = delta_calibration_radius();
- LOOP_CAL_ALL(rad) {
- const float a = RADIANS(210 + (360 / NPP) * (rad - 1)),
- r = (rad == CEN ? 0.0f : dcr);
- pos.set(cos(a) * r, sin(a) * r, z_pt[rad]);
- inverse_kinematics(pos);
- mm_at_pt_axis[rad] = delta;
- }
- }
-
- static void forward_kinematics_probe_points(abc_float_t mm_at_pt_axis[NPP + 1], float z_pt[NPP + 1]) {
- const float r_quot = delta_calibration_radius() / delta_radius;
-
- #define ZPP(N,I,A) (((1.0f + r_quot * (N)) / 3.0f) * mm_at_pt_axis[I].A)
- #define Z00(I, A) ZPP( 0, I, A)
- #define Zp1(I, A) ZPP(+1, I, A)
- #define Zm1(I, A) ZPP(-1, I, A)
- #define Zp2(I, A) ZPP(+2, I, A)
- #define Zm2(I, A) ZPP(-2, I, A)
-
- z_pt[CEN] = Z00(CEN, a) + Z00(CEN, b) + Z00(CEN, c);
- z_pt[__A] = Zp2(__A, a) + Zm1(__A, b) + Zm1(__A, c);
- z_pt[__B] = Zm1(__B, a) + Zp2(__B, b) + Zm1(__B, c);
- z_pt[__C] = Zm1(__C, a) + Zm1(__C, b) + Zp2(__C, c);
- z_pt[_BC] = Zm2(_BC, a) + Zp1(_BC, b) + Zp1(_BC, c);
- z_pt[_CA] = Zp1(_CA, a) + Zm2(_CA, b) + Zp1(_CA, c);
- z_pt[_AB] = Zp1(_AB, a) + Zp1(_AB, b) + Zm2(_AB, c);
- }
-
- static void calc_kinematics_diff_probe_points(float z_pt[NPP + 1], abc_float_t delta_e, const float delta_r, abc_float_t delta_t) {
- const float z_center = z_pt[CEN];
- abc_float_t diff_mm_at_pt_axis[NPP + 1], new_mm_at_pt_axis[NPP + 1];
-
- reverse_kinematics_probe_points(z_pt, diff_mm_at_pt_axis);
-
- delta_radius += delta_r;
- delta_tower_angle_trim += delta_t;
- recalc_delta_settings();
- reverse_kinematics_probe_points(z_pt, new_mm_at_pt_axis);
-
- LOOP_CAL_ALL(rad) diff_mm_at_pt_axis[rad] -= new_mm_at_pt_axis[rad] + delta_e;
- forward_kinematics_probe_points(diff_mm_at_pt_axis, z_pt);
-
- LOOP_CAL_RAD(rad) z_pt[rad] -= z_pt[CEN] - z_center;
- z_pt[CEN] = z_center;
-
- delta_radius -= delta_r;
- delta_tower_angle_trim -= delta_t;
- recalc_delta_settings();
- }
-
- static float auto_tune_h() {
- const float r_quot = delta_calibration_radius() / delta_radius;
- return RECIPROCAL(r_quot / (2.0f / 3.0f)); // (2/3)/CR
- }
-
- static float auto_tune_r() {
- constexpr float diff = 0.01f, delta_r = diff;
- float r_fac = 0.0f, z_pt[NPP + 1] = { 0.0f };
- abc_float_t delta_e = { 0.0f }, delta_t = { 0.0f };
-
- calc_kinematics_diff_probe_points(z_pt, delta_e, delta_r, delta_t);
- r_fac = -(z_pt[__A] + z_pt[__B] + z_pt[__C] + z_pt[_BC] + z_pt[_CA] + z_pt[_AB]) / 6.0f;
- r_fac = diff / r_fac / 3.0f; // 1/(3*delta_Z)
- return r_fac;
- }
-
- static float auto_tune_a() {
- constexpr float diff = 0.01f, delta_r = 0.0f;
- float a_fac = 0.0f, z_pt[NPP + 1] = { 0.0f };
- abc_float_t delta_e = { 0.0f }, delta_t = { 0.0f };
-
- delta_t.reset();
- LOOP_XYZ(axis) {
- delta_t[axis] = diff;
- calc_kinematics_diff_probe_points(z_pt, delta_e, delta_r, delta_t);
- delta_t[axis] = 0;
- a_fac += z_pt[uint8_t((axis * _4P_STEP) - _7P_STEP + NPP) % NPP + 1] / 6.0f;
- a_fac -= z_pt[uint8_t((axis * _4P_STEP) + 1 + _7P_STEP)] / 6.0f;
- }
- a_fac = diff / a_fac / 3.0f; // 1/(3*delta_Z)
- return a_fac;
- }
-
- /**
- * G33 - Delta '1-4-7-point' Auto-Calibration
- * Calibrate height, z_offset, endstops, delta radius, and tower angles.
- *
- * Parameters:
- *
- * Pn Number of probe points:
- * P0 Normalizes calibration.
- * P1 Calibrates height only with center probe.
- * P2 Probe center and towers. Calibrate height, endstops and delta radius.
- * P3 Probe all positions: center, towers and opposite towers. Calibrate all.
- * P4-P10 Probe all positions at different intermediate locations and average them.
- *
- * T Don't calibrate tower angle corrections
- *
- * Cn.nn Calibration precision; when omitted calibrates to maximum precision
- *
- * Fn Force to run at least n iterations and take the best result
- *
- * Vn Verbose level:
- * V0 Dry-run mode. Report settings and probe results. No calibration.
- * V1 Report start and end settings only
- * V2 Report settings at each iteration
- * V3 Report settings and probe results
- *
- * E Engage the probe for each point
- */
- void GcodeSuite::G33() {
-
- const int8_t probe_points = parser.intval('P', DELTA_CALIBRATION_DEFAULT_POINTS);
- if (!WITHIN(probe_points, 0, 10)) {
- SERIAL_ECHOLNPGM("?(P)oints implausible (0-10).");
- return;
- }
-
- const bool towers_set = !parser.seen('T');
-
- const float calibration_precision = parser.floatval('C', 0.0f);
- if (calibration_precision < 0) {
- SERIAL_ECHOLNPGM("?(C)alibration precision implausible (>=0).");
- return;
- }
-
- const int8_t force_iterations = parser.intval('F', 0);
- if (!WITHIN(force_iterations, 0, 30)) {
- SERIAL_ECHOLNPGM("?(F)orce iteration implausible (0-30).");
- return;
- }
-
- const int8_t verbose_level = parser.byteval('V', 1);
- if (!WITHIN(verbose_level, 0, 3)) {
- SERIAL_ECHOLNPGM("?(V)erbose level implausible (0-3).");
- return;
- }
-
- const bool stow_after_each = parser.seen('E');
-
- const bool _0p_calibration = probe_points == 0,
- _1p_calibration = probe_points == 1 || probe_points == -1,
- _4p_calibration = probe_points == 2,
- _4p_opposite_points = _4p_calibration && !towers_set,
- _7p_9_center = probe_points >= 8,
- _tower_results = (_4p_calibration && towers_set) || probe_points >= 3,
- _opposite_results = (_4p_calibration && !towers_set) || probe_points >= 3,
- _endstop_results = probe_points != 1 && probe_points != -1 && probe_points != 0,
- _angle_results = probe_points >= 3 && towers_set;
- int8_t iterations = 0;
- float test_precision,
- zero_std_dev = (verbose_level ? 999.0f : 0.0f), // 0.0 in dry-run mode : forced end
- zero_std_dev_min = zero_std_dev,
- zero_std_dev_old = zero_std_dev,
- h_factor, r_factor, a_factor,
- r_old = delta_radius,
- h_old = delta_height;
-
- abc_pos_t e_old = delta_endstop_adj, a_old = delta_tower_angle_trim;
-
- SERIAL_ECHOLNPGM("G33 Auto Calibrate");
-
- const float dcr = delta_calibration_radius();
-
- if (!_1p_calibration && !_0p_calibration) { // test if the outer radius is reachable
- LOOP_CAL_RAD(axis) {
- const float a = RADIANS(210 + (360 / NPP) * (axis - 1));
- if (!position_is_reachable(cos(a) * dcr, sin(a) * dcr)) {
- SERIAL_ECHOLNPGM("?Bed calibration radius implausible.");
- return;
- }
- }
- }
-
- // Report settings
- PGM_P const checkingac = PSTR("Checking... AC");
- serialprintPGM(checkingac);
- if (verbose_level == 0) SERIAL_ECHOPGM(" (DRY-RUN)");
- SERIAL_EOL();
- ui.set_status_P(checkingac);
-
- print_calibration_settings(_endstop_results, _angle_results);
-
- ac_setup(!_0p_calibration && !_1p_calibration);
-
- if (!_0p_calibration) ac_home();
-
- do { // start iterations
-
- float z_at_pt[NPP + 1] = { 0.0f };
-
- test_precision = zero_std_dev_old != 999.0f ? (zero_std_dev + zero_std_dev_old) / 2.0f : zero_std_dev;
- iterations++;
-
- // Probe the points
- zero_std_dev_old = zero_std_dev;
- if (!probe_calibration_points(z_at_pt, probe_points, towers_set, stow_after_each)) {
- SERIAL_ECHOLNPGM("Correct delta settings with M665 and M666");
- return ac_cleanup(TERN_(HAS_MULTI_HOTEND, old_tool_index));
- }
- zero_std_dev = std_dev_points(z_at_pt, _0p_calibration, _1p_calibration, _4p_calibration, _4p_opposite_points);
-
- // Solve matrices
-
- if ((zero_std_dev < test_precision || iterations <= force_iterations) && zero_std_dev > calibration_precision) {
-
- #if !HAS_BED_PROBE
- test_precision = 0.0f; // forced end
- #endif
-
- if (zero_std_dev < zero_std_dev_min) {
- // set roll-back point
- e_old = delta_endstop_adj;
- r_old = delta_radius;
- h_old = delta_height;
- a_old = delta_tower_angle_trim;
- }
-
- abc_float_t e_delta = { 0.0f }, t_delta = { 0.0f };
- float r_delta = 0.0f;
-
- /**
- * convergence matrices:
- * see https://github.com/LVD-AC/Marlin-AC/tree/1.1.x-AC/documentation for
- * - definition of the matrix scaling parameters
- * - matrices for 4 and 7 point calibration
- */
- #define ZP(N,I) ((N) * z_at_pt[I] / 4.0f) // 4.0 = divider to normalize to integers
- #define Z12(I) ZP(12, I)
- #define Z4(I) ZP(4, I)
- #define Z2(I) ZP(2, I)
- #define Z1(I) ZP(1, I)
- #define Z0(I) ZP(0, I)
-
- // calculate factors
- if (_7p_9_center) calibration_radius_factor = 0.9f;
- h_factor = auto_tune_h();
- r_factor = auto_tune_r();
- a_factor = auto_tune_a();
- calibration_radius_factor = 1.0f;
-
- switch (probe_points) {
- case 0:
- test_precision = 0.0f; // forced end
- break;
-
- case 1:
- test_precision = 0.0f; // forced end
- LOOP_XYZ(axis) e_delta[axis] = +Z4(CEN);
- break;
-
- case 2:
- if (towers_set) { // see 4 point calibration (towers) matrix
- e_delta.set((+Z4(__A) -Z2(__B) -Z2(__C)) * h_factor +Z4(CEN),
- (-Z2(__A) +Z4(__B) -Z2(__C)) * h_factor +Z4(CEN),
- (-Z2(__A) -Z2(__B) +Z4(__C)) * h_factor +Z4(CEN));
- r_delta = (+Z4(__A) +Z4(__B) +Z4(__C) -Z12(CEN)) * r_factor;
- }
- else { // see 4 point calibration (opposites) matrix
- e_delta.set((-Z4(_BC) +Z2(_CA) +Z2(_AB)) * h_factor +Z4(CEN),
- (+Z2(_BC) -Z4(_CA) +Z2(_AB)) * h_factor +Z4(CEN),
- (+Z2(_BC) +Z2(_CA) -Z4(_AB)) * h_factor +Z4(CEN));
- r_delta = (+Z4(_BC) +Z4(_CA) +Z4(_AB) -Z12(CEN)) * r_factor;
- }
- break;
-
- default: // see 7 point calibration (towers & opposites) matrix
- e_delta.set((+Z2(__A) -Z1(__B) -Z1(__C) -Z2(_BC) +Z1(_CA) +Z1(_AB)) * h_factor +Z4(CEN),
- (-Z1(__A) +Z2(__B) -Z1(__C) +Z1(_BC) -Z2(_CA) +Z1(_AB)) * h_factor +Z4(CEN),
- (-Z1(__A) -Z1(__B) +Z2(__C) +Z1(_BC) +Z1(_CA) -Z2(_AB)) * h_factor +Z4(CEN));
- r_delta = (+Z2(__A) +Z2(__B) +Z2(__C) +Z2(_BC) +Z2(_CA) +Z2(_AB) -Z12(CEN)) * r_factor;
-
- if (towers_set) { // see 7 point tower angle calibration (towers & opposites) matrix
- t_delta.set((+Z0(__A) -Z4(__B) +Z4(__C) +Z0(_BC) -Z4(_CA) +Z4(_AB) +Z0(CEN)) * a_factor,
- (+Z4(__A) +Z0(__B) -Z4(__C) +Z4(_BC) +Z0(_CA) -Z4(_AB) +Z0(CEN)) * a_factor,
- (-Z4(__A) +Z4(__B) +Z0(__C) -Z4(_BC) +Z4(_CA) +Z0(_AB) +Z0(CEN)) * a_factor);
- }
- break;
- }
- delta_endstop_adj += e_delta;
- delta_radius += r_delta;
- delta_tower_angle_trim += t_delta;
- }
- else if (zero_std_dev >= test_precision) {
- // roll back
- delta_endstop_adj = e_old;
- delta_radius = r_old;
- delta_height = h_old;
- delta_tower_angle_trim = a_old;
- }
-
- if (verbose_level != 0) { // !dry run
-
- // Normalize angles to least-squares
- if (_angle_results) {
- float a_sum = 0.0f;
- LOOP_XYZ(axis) a_sum += delta_tower_angle_trim[axis];
- LOOP_XYZ(axis) delta_tower_angle_trim[axis] -= a_sum / 3.0f;
- }
-
- // adjust delta_height and endstops by the max amount
- const float z_temp = _MAX(delta_endstop_adj.a, delta_endstop_adj.b, delta_endstop_adj.c);
- delta_height -= z_temp;
- LOOP_XYZ(axis) delta_endstop_adj[axis] -= z_temp;
- }
- recalc_delta_settings();
- NOMORE(zero_std_dev_min, zero_std_dev);
-
- // print report
-
- if (verbose_level == 3)
- print_calibration_results(z_at_pt, _tower_results, _opposite_results);
-
- if (verbose_level != 0) { // !dry run
- if ((zero_std_dev >= test_precision && iterations > force_iterations) || zero_std_dev <= calibration_precision) { // end iterations
- SERIAL_ECHOPGM("Calibration OK");
- SERIAL_ECHO_SP(32);
- #if HAS_BED_PROBE
- if (zero_std_dev >= test_precision && !_1p_calibration && !_0p_calibration)
- SERIAL_ECHOPGM("rolling back.");
- else
- #endif
- {
- SERIAL_ECHOPAIR_F("std dev:", zero_std_dev_min, 3);
- }
- SERIAL_EOL();
- char mess[21];
- strcpy_P(mess, PSTR("Calibration sd:"));
- if (zero_std_dev_min < 1)
- sprintf_P(&mess[15], PSTR("0.%03i"), (int)LROUND(zero_std_dev_min * 1000.0f));
- else
- sprintf_P(&mess[15], PSTR("%03i.x"), (int)LROUND(zero_std_dev_min));
- ui.set_status(mess);
- print_calibration_settings(_endstop_results, _angle_results);
- SERIAL_ECHOLNPGM("Save with M500 and/or copy to Configuration.h");
- }
- else { // !end iterations
- char mess[15];
- if (iterations < 31)
- sprintf_P(mess, PSTR("Iteration : %02i"), (unsigned int)iterations);
- else
- strcpy_P(mess, PSTR("No convergence"));
- SERIAL_ECHO(mess);
- SERIAL_ECHO_SP(32);
- SERIAL_ECHOLNPAIR_F("std dev:", zero_std_dev, 3);
- ui.set_status(mess);
- if (verbose_level > 1)
- print_calibration_settings(_endstop_results, _angle_results);
- }
- }
- else { // dry run
- PGM_P const enddryrun = PSTR("End DRY-RUN");
- serialprintPGM(enddryrun);
- SERIAL_ECHO_SP(35);
- SERIAL_ECHOLNPAIR_F("std dev:", zero_std_dev, 3);
-
- char mess[21];
- strcpy_P(mess, enddryrun);
- strcpy_P(&mess[11], PSTR(" sd:"));
- if (zero_std_dev < 1)
- sprintf_P(&mess[15], PSTR("0.%03i"), (int)LROUND(zero_std_dev * 1000.0f));
- else
- sprintf_P(&mess[15], PSTR("%03i.x"), (int)LROUND(zero_std_dev));
- ui.set_status(mess);
- }
- ac_home();
- }
- while (((zero_std_dev < test_precision && iterations < 31) || iterations <= force_iterations) && zero_std_dev > calibration_precision);
-
- ac_cleanup(TERN_(HAS_MULTI_HOTEND, old_tool_index));
- }
-
- #endif // DELTA_AUTO_CALIBRATION
|