marlin/Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_...

/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * Based on u8g_com_LPC1768_st7920_hw_spi.c
 *
 * Universal 8bit Graphics Library
 *
 * Copyright (c) 2011, olikraus@gmail.com
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without modification,
 * are permitted provided that the following conditions are met:
 *
 *  * Redistributions of source code must retain the above copyright notice, this list
 *    of conditions and the following disclaimer.
 *
 *  * Redistributions in binary form must reproduce the above copyright notice, this
 *    list of conditions and the following disclaimer in the documentation and/or other
 *    materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
 * CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
 * INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
 * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

#ifdef TARGET_LPC1768

#include "../../../inc/MarlinConfigPre.h"

#if HAS_GRAPHICAL_LCD

//#include <inttypes.h>
#include <U8glib.h>
#include "../../shared/Delay.h"

#define SPI_FULL_SPEED 0
#define SPI_HALF_SPEED 1
#define SPI_QUARTER_SPEED 2
#define SPI_EIGHTH_SPEED 3
#define SPI_SIXTEENTH_SPEED 4
#define SPI_SPEED_5 5
#define SPI_SPEED_6 6

void spiBegin();
void spiInit(uint8_t spiRate);
void spiSend(uint8_t b);
void spiSend(const uint8_t* buf, size_t n);

static uint8_t rs_last_state = 255;

static void u8g_com_LPC1768_st7920_write_byte_hw_spi(uint8_t rs, uint8_t val) {

  if (rs != rs_last_state) {      // Time to send a command/data byte
    rs_last_state = rs;
    spiSend(rs ? 0x0FA : 0x0F8);  // Send data or command
    DELAY_US(40);                 // Give the controller some time: 20 is bad, 30 is OK, 40 is safe
  }

  spiSend(val & 0xF0);
  spiSend(val << 4);
}

uint8_t u8g_com_HAL_LPC1768_ST7920_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {
  switch(msg) {
    case U8G_COM_MSG_INIT:
      u8g_SetPILevel(u8g, U8G_PI_CS, 0);
      u8g_SetPIOutput(u8g, U8G_PI_CS);
      u8g_Delay(5);
      spiBegin();
      spiInit(SPI_EIGHTH_SPEED);            // ST7920 max speed is about 1.1 MHz
      u8g->pin_list[U8G_PI_A0_STATE] = 0;   // initial RS state: command mode
      break;

    case U8G_COM_MSG_STOP:
      break;

    case U8G_COM_MSG_RESET:
      u8g_SetPILevel(u8g, U8G_PI_RESET, arg_val);
      break;

    case U8G_COM_MSG_ADDRESS:                   // Define cmd (arg_val = 0) or data mode (arg_val = 1)
      u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
      break;

    case U8G_COM_MSG_CHIP_SELECT:
      u8g_SetPILevel(u8g, U8G_PI_CS, arg_val);  // Note: the ST7920 has an active high chip-select
      break;

    case U8G_COM_MSG_WRITE_BYTE:
      u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], arg_val);
      break;

    case U8G_COM_MSG_WRITE_SEQ: {
        uint8_t *ptr = (uint8_t*) arg_ptr;
        while (arg_val > 0) {
          u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
          arg_val--;
        }
      }
      break;

      case U8G_COM_MSG_WRITE_SEQ_P: {
        uint8_t *ptr = (uint8_t*) arg_ptr;
        while (arg_val > 0) {
          u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
          arg_val--;
        }
      }
      break;
  }
  return 1;
}

#endif // HAS_GRAPHICAL_LCD

#endif // TARGET_LPC1768