My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Você não pode selecionar mais de 25 tópicos Os tópicos devem começar com uma letra ou um número, podem incluir traços ('-') e podem ter até 35 caracteres.

Configuration.h 79KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510610710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916016116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321421521621721821922022122222322422522622722822923023123223323423523623723823924024124224324424524624724824925025125225325425525625725825926026126226326426526626726826927027127227327427527627727827928028128228328428528628728828929029129229329429529629729829930030130230330430530630730830931031131231331431531631731831932032132232332432532632732832933033133233333433533633733833934034134234334434534634734834935035135235335435535635735835936036136236336436536636736836937037137237337437537637737837938038138238338438538638738838939039139239339439539639739839940040140240340440540640740840941041141241341441541641741841942042142242342442542642742842943043143243343443543643743843944044144244344444544644744844945045145245345445545645745845946046146246346446546646746846947047147247347447547647747847948048148248348448548648748848949049149249349449549649749849950050150250350450550650750850951051151251351451551651751851952052152252352452552652752852953053153253353453553653753853954054154254354454554654754854955055155255355455555655755855956056156256356456556656756856957057157257357457557657757857958058158258358458558658758858959059159259359459559659759859960060160260360460560660760860961061161261361461561661761861962062162262362462562662762862963063163263363463563663763863964064164264364464564664764864965065165265365465565665765865966066166266366466566666766866967067167267367467567667767867968068168268368468568668768868969069169269369469569669769869970070170270370470570670770870971071171271371471571671771871972072172272372472572672772872973073173273373473573673773873974074174274374474574674774874975075175275375475575675775875976076176276376476576676776876977077177277377477577677777877978078178278378478578678778878979079179279379479579679779879980080180280380480580680780880981081181281381481581681781881982082182282382482582682782882983083183283383483583683783883984084184284384484584684784884985085185285385485585685785885986086186286386486586686786886987087187287387487587687787887988088188288388488588688788888989089189289389489589689789889990090190290390490590690790890991091191291391491591691791891992092192292392492592692792892993093193293393493593693793893994094194294394494594694794894995095195295395495595695795895996096196296396496596696796896997097197297397497597697797897998098198298398498598698798898999099199299399499599699799899910001001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025102610271028102910301031103210331034103510361037103810391040104110421043104410451046104710481049105010511052105310541055105610571058105910601061106210631064106510661067106810691070107110721073107410751076107710781079108010811082108310841085108610871088108910901091109210931094109510961097109810991100110111021103110411051106110711081109111011111112111311141115111611171118111911201121112211231124112511261127112811291130113111321133113411351136113711381139114011411142114311441145114611471148114911501151115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175117611771178117911801181118211831184118511861187118811891190119111921193119411951196119711981199120012011202120312041205120612071208120912101211121212131214121512161217121812191220122112221223122412251226122712281229123012311232123312341235123612371238123912401241124212431244124512461247124812491250125112521253125412551256125712581259126012611262126312641265126612671268126912701271127212731274127512761277127812791280128112821283128412851286128712881289129012911292129312941295129612971298129913001301130213031304130513061307130813091310131113121313131413151316131713181319132013211322132313241325132613271328132913301331133213331334133513361337133813391340134113421343134413451346134713481349135013511352135313541355135613571358135913601361136213631364136513661367136813691370137113721373137413751376137713781379138013811382138313841385138613871388138913901391139213931394139513961397139813991400140114021403140414051406140714081409141014111412141314141415141614171418141914201421142214231424142514261427142814291430143114321433143414351436143714381439144014411442144314441445144614471448144914501451145214531454145514561457145814591460146114621463146414651466146714681469147014711472147314741475147614771478147914801481148214831484148514861487148814891490149114921493149414951496149714981499150015011502150315041505150615071508150915101511151215131514151515161517151815191520152115221523152415251526152715281529153015311532153315341535153615371538153915401541154215431544154515461547154815491550155115521553155415551556155715581559156015611562156315641565156615671568156915701571157215731574157515761577157815791580158115821583158415851586158715881589159015911592159315941595159615971598159916001601160216031604160516061607160816091610161116121613161416151616161716181619162016211622162316241625162616271628162916301631163216331634163516361637163816391640164116421643164416451646164716481649165016511652165316541655165616571658165916601661166216631664166516661667166816691670167116721673167416751676167716781679168016811682168316841685168616871688168916901691169216931694169516961697169816991700170117021703170417051706170717081709171017111712171317141715171617171718171917201721172217231724172517261727172817291730173117321733173417351736173717381739174017411742174317441745174617471748174917501751175217531754175517561757175817591760176117621763176417651766176717681769177017711772177317741775177617771778177917801781178217831784178517861787178817891790179117921793179417951796179717981799180018011802180318041805180618071808180918101811181218131814181518161817181818191820182118221823182418251826182718281829183018311832183318341835183618371838183918401841184218431844184518461847184818491850185118521853185418551856185718581859186018611862186318641865186618671868186918701871187218731874187518761877187818791880188118821883188418851886188718881889189018911892189318941895189618971898189919001901190219031904190519061907190819091910191119121913191419151916191719181919192019211922192319241925192619271928192919301931193219331934193519361937193819391940194119421943194419451946194719481949195019511952195319541955195619571958195919601961196219631964196519661967196819691970197119721973197419751976197719781979198019811982198319841985198619871988198919901991199219931994199519961997199819992000200120022003200420052006200720082009201020112012201320142015201620172018201920202021202220232024202520262027202820292030203120322033203420352036203720382039204020412042204320442045204620472048204920502051205220532054205520562057205820592060206120622063206420652066206720682069207020712072207320742075207620772078207920802081208220832084208520862087208820892090209120922093209420952096209720982099210021012102210321042105210621072108210921102111211221132114211521162117211821192120212121222123212421252126212721282129213021312132213321342135213621372138213921402141214221432144214521462147214821492150215121522153215421552156215721582159216021612162216321642165216621672168216921702171217221732174217521762177217821792180218121822183218421852186218721882189219021912192219321942195219621972198219922002201220222032204220522062207220822092210
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #define CONFIGURATION_H_VERSION 020000
  39. //===========================================================================
  40. //============================= Getting Started =============================
  41. //===========================================================================
  42. /**
  43. * Here are some standard links for getting your machine calibrated:
  44. *
  45. * http://reprap.org/wiki/Calibration
  46. * http://youtu.be/wAL9d7FgInk
  47. * http://calculator.josefprusa.cz
  48. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  49. * http://www.thingiverse.com/thing:5573
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * http://www.thingiverse.com/thing:298812
  52. */
  53. //===========================================================================
  54. //============================= DELTA Printer ===============================
  55. //===========================================================================
  56. // For a Delta printer start with one of the configuration files in the
  57. // config/examples/delta directory and customize for your machine.
  58. //
  59. //===========================================================================
  60. //============================= SCARA Printer ===============================
  61. //===========================================================================
  62. // For a SCARA printer start with the configuration files in
  63. // config/examples/SCARA and customize for your machine.
  64. //
  65. // @section info
  66. // Author info of this build printed to the host during boot and M115
  67. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  68. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  69. /**
  70. * *** VENDORS PLEASE READ ***
  71. *
  72. * Marlin allows you to add a custom boot image for Graphical LCDs.
  73. * With this option Marlin will first show your custom screen followed
  74. * by the standard Marlin logo with version number and web URL.
  75. *
  76. * We encourage you to take advantage of this new feature and we also
  77. * respectfully request that you retain the unmodified Marlin boot screen.
  78. */
  79. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  80. #define SHOW_BOOTSCREEN
  81. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  82. //#define SHOW_CUSTOM_BOOTSCREEN
  83. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  84. //#define CUSTOM_STATUS_SCREEN_IMAGE
  85. // @section machine
  86. /**
  87. * Select the serial port on the board to use for communication with the host.
  88. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT 0
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  97. * Serial port -1 is the USB emulated serial port, if available.
  98. *
  99. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  100. */
  101. //#define SERIAL_PORT_2 -1
  102. /**
  103. * This setting determines the communication speed of the printer.
  104. *
  105. * 250000 works in most cases, but you might try a lower speed if
  106. * you commonly experience drop-outs during host printing.
  107. * You may try up to 1000000 to speed up SD file transfer.
  108. *
  109. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  110. */
  111. #define BAUDRATE 250000
  112. // Enable the Bluetooth serial interface on AT90USB devices
  113. //#define BLUETOOTH
  114. // Choose the name from boards.h that matches your setup
  115. #ifndef MOTHERBOARD
  116. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  117. #endif
  118. // Name displayed in the LCD "Ready" message and Info menu
  119. //#define CUSTOM_MACHINE_NAME "3D Printer"
  120. // Printer's unique ID, used by some programs to differentiate between machines.
  121. // Choose your own or use a service like http://www.uuidgenerator.net/version4
  122. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  123. // @section extruder
  124. // This defines the number of extruders
  125. // :[1, 2, 3, 4, 5, 6]
  126. #define EXTRUDERS 1
  127. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  128. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
  129. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  130. //#define SINGLENOZZLE
  131. /**
  132. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  133. *
  134. * This device allows one stepper driver on a control board to drive
  135. * two to eight stepper motors, one at a time, in a manner suitable
  136. * for extruders.
  137. *
  138. * This option only allows the multiplexer to switch on tool-change.
  139. * Additional options to configure custom E moves are pending.
  140. */
  141. //#define MK2_MULTIPLEXER
  142. #if ENABLED(MK2_MULTIPLEXER)
  143. // Override the default DIO selector pins here, if needed.
  144. // Some pins files may provide defaults for these pins.
  145. //#define E_MUX0_PIN 40 // Always Required
  146. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  147. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  148. #endif
  149. /**
  150. * Prusa Multi-Material Unit v2
  151. *
  152. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  153. * Requires EXTRUDERS = 5
  154. *
  155. * For additional configuration see Configuration_adv.h
  156. */
  157. //#define PRUSA_MMU2
  158. // A dual extruder that uses a single stepper motor
  159. //#define SWITCHING_EXTRUDER
  160. #if ENABLED(SWITCHING_EXTRUDER)
  161. #define SWITCHING_EXTRUDER_SERVO_NR 0
  162. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  163. #if EXTRUDERS > 3
  164. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  165. #endif
  166. #endif
  167. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  168. //#define SWITCHING_NOZZLE
  169. #if ENABLED(SWITCHING_NOZZLE)
  170. #define SWITCHING_NOZZLE_SERVO_NR 0
  171. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  172. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  173. #endif
  174. /**
  175. * Two separate X-carriages with extruders that connect to a moving part
  176. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  177. */
  178. //#define PARKING_EXTRUDER
  179. /**
  180. * Two separate X-carriages with extruders that connect to a moving part
  181. * via a magnetic docking mechanism using movements and no solenoid
  182. *
  183. * project : https://www.thingiverse.com/thing:3080893
  184. * movements : https://youtu.be/0xCEiG9VS3k
  185. * https://youtu.be/Bqbcs0CU2FE
  186. */
  187. //#define MAGNETIC_PARKING_EXTRUDER
  188. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  189. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  190. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  191. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  192. #if ENABLED(PARKING_EXTRUDER)
  193. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  194. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  195. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  196. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  197. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  198. #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
  199. #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
  200. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  201. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  202. #endif
  203. #endif
  204. /**
  205. * Switching Toolhead
  206. *
  207. * Support for swappable and dockable toolheads, such as
  208. * the E3D Tool Changer. Toolheads are locked with a servo.
  209. */
  210. //#define SWITCHING_TOOLHEAD
  211. /**
  212. * Magnetic Switching Toolhead
  213. *
  214. * Support swappable and dockable toolheads with a magnetic
  215. * docking mechanism using movement and no servo.
  216. */
  217. //#define MAGNETIC_SWITCHING_TOOLHEAD
  218. /**
  219. * Electromagnetic Switching Toolhead
  220. *
  221. * Parking for CoreXY / HBot kinematics.
  222. * Toolheads are parked at one edge and held with an electromagnet.
  223. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  224. */
  225. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  226. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  227. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  228. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  229. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  230. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  231. #if ENABLED(SWITCHING_TOOLHEAD)
  232. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  233. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  234. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  235. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  236. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  237. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  238. #if ENABLED(PRIME_BEFORE_REMOVE)
  239. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  240. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  241. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate
  242. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate
  243. #endif
  244. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  245. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  246. #endif
  247. #endif
  248. /**
  249. * "Mixing Extruder"
  250. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  251. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  252. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  253. * - This implementation supports up to two mixing extruders.
  254. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  255. */
  256. //#define MIXING_EXTRUDER
  257. #if ENABLED(MIXING_EXTRUDER)
  258. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  259. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  260. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  261. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  262. #if ENABLED(GRADIENT_MIX)
  263. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  264. #endif
  265. #endif
  266. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  267. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  268. // For the other hotends it is their distance from the extruder 0 hotend.
  269. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  270. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  271. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  272. // @section machine
  273. /**
  274. * Power Supply Control
  275. *
  276. * Enable and connect the power supply to the PS_ON_PIN.
  277. * Specify whether the power supply is active HIGH or active LOW.
  278. */
  279. //#define PSU_CONTROL
  280. //#define PSU_NAME "Power Supply"
  281. #if ENABLED(PSU_CONTROL)
  282. #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
  283. //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80
  284. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  285. #if ENABLED(AUTO_POWER_CONTROL)
  286. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  287. #define AUTO_POWER_E_FANS
  288. #define AUTO_POWER_CONTROLLERFAN
  289. #define AUTO_POWER_CHAMBER_FAN
  290. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature
  291. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature
  292. #define POWER_TIMEOUT 30
  293. #endif
  294. #endif
  295. // @section temperature
  296. //===========================================================================
  297. //============================= Thermal Settings ============================
  298. //===========================================================================
  299. /**
  300. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  301. *
  302. * Temperature sensors available:
  303. *
  304. * -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
  305. * -3 : thermocouple with MAX31855 (only for sensors 0-1)
  306. * -2 : thermocouple with MAX6675 (only for sensors 0-1)
  307. * -4 : thermocouple with AD8495
  308. * -1 : thermocouple with AD595
  309. * 0 : not used
  310. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  311. * 331 : (3.3V scaled thermistor 1 table)
  312. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  313. * 3 : Mendel-parts thermistor (4.7k pullup)
  314. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  315. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  316. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  317. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  318. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  319. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  320. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  321. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  322. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  323. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  324. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  325. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  326. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  327. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  328. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  329. * 20 : Pt100 with circuit in the Ultimainboard V2.x
  330. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  331. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  332. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  333. * 66 : 4.7M High Temperature thermistor from Dyze Design
  334. * 67 : 450C thermistor from SliceEngineering
  335. * 70 : the 100K thermistor found in the bq Hephestos 2
  336. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  337. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  338. *
  339. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  340. * (but gives greater accuracy and more stable PID)
  341. * 51 : 100k thermistor - EPCOS (1k pullup)
  342. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  343. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  344. *
  345. * 1047 : Pt1000 with 4k7 pullup
  346. * 1010 : Pt1000 with 1k pullup (non standard)
  347. * 147 : Pt100 with 4k7 pullup
  348. * 110 : Pt100 with 1k pullup (non standard)
  349. *
  350. * 1000 : Custom - Specify parameters in Configuration_adv.h
  351. *
  352. * Use these for Testing or Development purposes. NEVER for production machine.
  353. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  354. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  355. */
  356. #define TEMP_SENSOR_0 1
  357. #define TEMP_SENSOR_1 0
  358. #define TEMP_SENSOR_2 0
  359. #define TEMP_SENSOR_3 0
  360. #define TEMP_SENSOR_4 0
  361. #define TEMP_SENSOR_5 0
  362. #define TEMP_SENSOR_BED 0
  363. #define TEMP_SENSOR_CHAMBER 0
  364. // Dummy thermistor constant temperature readings, for use with 998 and 999
  365. #define DUMMY_THERMISTOR_998_VALUE 25
  366. #define DUMMY_THERMISTOR_999_VALUE 100
  367. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  368. // from the two sensors differ too much the print will be aborted.
  369. //#define TEMP_SENSOR_1_AS_REDUNDANT
  370. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  371. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  372. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  373. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  374. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  375. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  376. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  377. // Below this temperature the heater will be switched off
  378. // because it probably indicates a broken thermistor wire.
  379. #define HEATER_0_MINTEMP 5
  380. #define HEATER_1_MINTEMP 5
  381. #define HEATER_2_MINTEMP 5
  382. #define HEATER_3_MINTEMP 5
  383. #define HEATER_4_MINTEMP 5
  384. #define HEATER_5_MINTEMP 5
  385. #define BED_MINTEMP 5
  386. // Above this temperature the heater will be switched off.
  387. // This can protect components from overheating, but NOT from shorts and failures.
  388. // (Use MINTEMP for thermistor short/failure protection.)
  389. #define HEATER_0_MAXTEMP 275
  390. #define HEATER_1_MAXTEMP 275
  391. #define HEATER_2_MAXTEMP 275
  392. #define HEATER_3_MAXTEMP 275
  393. #define HEATER_4_MAXTEMP 275
  394. #define HEATER_5_MAXTEMP 275
  395. #define BED_MAXTEMP 150
  396. //===========================================================================
  397. //============================= PID Settings ================================
  398. //===========================================================================
  399. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  400. // Comment the following line to disable PID and enable bang-bang.
  401. #define PIDTEMP
  402. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  403. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  404. #define PID_K1 0.95 // Smoothing factor within any PID loop
  405. #if ENABLED(PIDTEMP)
  406. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  407. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  408. //#define PID_DEBUG // Sends debug data to the serial port.
  409. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  410. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  411. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  412. // Set/get with gcode: M301 E[extruder number, 0-2]
  413. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  414. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  415. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  416. // Ultimaker
  417. #define DEFAULT_Kp 22.2
  418. #define DEFAULT_Ki 1.08
  419. #define DEFAULT_Kd 114
  420. // MakerGear
  421. //#define DEFAULT_Kp 7.0
  422. //#define DEFAULT_Ki 0.1
  423. //#define DEFAULT_Kd 12
  424. // Mendel Parts V9 on 12V
  425. //#define DEFAULT_Kp 63.0
  426. //#define DEFAULT_Ki 2.25
  427. //#define DEFAULT_Kd 440
  428. #endif // PIDTEMP
  429. //===========================================================================
  430. //====================== PID > Bed Temperature Control ======================
  431. //===========================================================================
  432. /**
  433. * PID Bed Heating
  434. *
  435. * If this option is enabled set PID constants below.
  436. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  437. *
  438. * The PID frequency will be the same as the extruder PWM.
  439. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  440. * which is fine for driving a square wave into a resistive load and does not significantly
  441. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  442. * heater. If your configuration is significantly different than this and you don't understand
  443. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  444. */
  445. //#define PIDTEMPBED
  446. //#define BED_LIMIT_SWITCHING
  447. /**
  448. * Max Bed Power
  449. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  450. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  451. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  452. */
  453. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  454. #if ENABLED(PIDTEMPBED)
  455. //#define MIN_BED_POWER 0
  456. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  457. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  458. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  459. #define DEFAULT_bedKp 10.00
  460. #define DEFAULT_bedKi .023
  461. #define DEFAULT_bedKd 305.4
  462. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  463. //from pidautotune
  464. //#define DEFAULT_bedKp 97.1
  465. //#define DEFAULT_bedKi 1.41
  466. //#define DEFAULT_bedKd 1675.16
  467. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  468. #endif // PIDTEMPBED
  469. // @section extruder
  470. /**
  471. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  472. * Add M302 to set the minimum extrusion temperature and/or turn
  473. * cold extrusion prevention on and off.
  474. *
  475. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  476. */
  477. #define PREVENT_COLD_EXTRUSION
  478. #define EXTRUDE_MINTEMP 170
  479. /**
  480. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  481. * Note: For Bowden Extruders make this large enough to allow load/unload.
  482. */
  483. #define PREVENT_LENGTHY_EXTRUDE
  484. #define EXTRUDE_MAXLENGTH 200
  485. //===========================================================================
  486. //======================== Thermal Runaway Protection =======================
  487. //===========================================================================
  488. /**
  489. * Thermal Protection provides additional protection to your printer from damage
  490. * and fire. Marlin always includes safe min and max temperature ranges which
  491. * protect against a broken or disconnected thermistor wire.
  492. *
  493. * The issue: If a thermistor falls out, it will report the much lower
  494. * temperature of the air in the room, and the the firmware will keep
  495. * the heater on.
  496. *
  497. * If you get "Thermal Runaway" or "Heating failed" errors the
  498. * details can be tuned in Configuration_adv.h
  499. */
  500. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  501. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  502. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  503. //===========================================================================
  504. //============================= Mechanical Settings =========================
  505. //===========================================================================
  506. // @section machine
  507. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  508. // either in the usual order or reversed
  509. //#define COREXY
  510. //#define COREXZ
  511. //#define COREYZ
  512. //#define COREYX
  513. //#define COREZX
  514. //#define COREZY
  515. //===========================================================================
  516. //============================== Endstop Settings ===========================
  517. //===========================================================================
  518. // @section homing
  519. // Specify here all the endstop connectors that are connected to any endstop or probe.
  520. // Almost all printers will be using one per axis. Probes will use one or more of the
  521. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  522. #define USE_XMIN_PLUG
  523. #define USE_YMIN_PLUG
  524. #define USE_ZMIN_PLUG
  525. //#define USE_XMAX_PLUG
  526. //#define USE_YMAX_PLUG
  527. //#define USE_ZMAX_PLUG
  528. // Enable pullup for all endstops to prevent a floating state
  529. #define ENDSTOPPULLUPS
  530. #if DISABLED(ENDSTOPPULLUPS)
  531. // Disable ENDSTOPPULLUPS to set pullups individually
  532. //#define ENDSTOPPULLUP_XMAX
  533. //#define ENDSTOPPULLUP_YMAX
  534. //#define ENDSTOPPULLUP_ZMAX
  535. //#define ENDSTOPPULLUP_XMIN
  536. //#define ENDSTOPPULLUP_YMIN
  537. //#define ENDSTOPPULLUP_ZMIN
  538. //#define ENDSTOPPULLUP_ZMIN_PROBE
  539. #endif
  540. // Enable pulldown for all endstops to prevent a floating state
  541. //#define ENDSTOPPULLDOWNS
  542. #if DISABLED(ENDSTOPPULLDOWNS)
  543. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  544. //#define ENDSTOPPULLDOWN_XMAX
  545. //#define ENDSTOPPULLDOWN_YMAX
  546. //#define ENDSTOPPULLDOWN_ZMAX
  547. //#define ENDSTOPPULLDOWN_XMIN
  548. //#define ENDSTOPPULLDOWN_YMIN
  549. //#define ENDSTOPPULLDOWN_ZMIN
  550. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  551. #endif
  552. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  553. #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  554. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  555. #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  556. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  557. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  558. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  559. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
  560. /**
  561. * Stepper Drivers
  562. *
  563. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  564. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  565. *
  566. * A4988 is assumed for unspecified drivers.
  567. *
  568. * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  569. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  570. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  571. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  572. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  573. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  574. */
  575. //#define X_DRIVER_TYPE A4988
  576. //#define Y_DRIVER_TYPE A4988
  577. //#define Z_DRIVER_TYPE A4988
  578. //#define X2_DRIVER_TYPE A4988
  579. //#define Y2_DRIVER_TYPE A4988
  580. //#define Z2_DRIVER_TYPE A4988
  581. //#define Z3_DRIVER_TYPE A4988
  582. //#define E0_DRIVER_TYPE A4988
  583. //#define E1_DRIVER_TYPE A4988
  584. //#define E2_DRIVER_TYPE A4988
  585. //#define E3_DRIVER_TYPE A4988
  586. //#define E4_DRIVER_TYPE A4988
  587. //#define E5_DRIVER_TYPE A4988
  588. // Enable this feature if all enabled endstop pins are interrupt-capable.
  589. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  590. //#define ENDSTOP_INTERRUPTS_FEATURE
  591. /**
  592. * Endstop Noise Threshold
  593. *
  594. * Enable if your probe or endstops falsely trigger due to noise.
  595. *
  596. * - Higher values may affect repeatability or accuracy of some bed probes.
  597. * - To fix noise install a 100nF ceramic capacitor inline with the switch.
  598. * - This feature is not required for common micro-switches mounted on PCBs
  599. * based on the Makerbot design, which already have the 100nF capacitor.
  600. *
  601. * :[2,3,4,5,6,7]
  602. */
  603. //#define ENDSTOP_NOISE_THRESHOLD 2
  604. //=============================================================================
  605. //============================== Movement Settings ============================
  606. //=============================================================================
  607. // @section motion
  608. /**
  609. * Default Settings
  610. *
  611. * These settings can be reset by M502
  612. *
  613. * Note that if EEPROM is enabled, saved values will override these.
  614. */
  615. /**
  616. * With this option each E stepper can have its own factors for the
  617. * following movement settings. If fewer factors are given than the
  618. * total number of extruders, the last value applies to the rest.
  619. */
  620. //#define DISTINCT_E_FACTORS
  621. /**
  622. * Default Axis Steps Per Unit (steps/mm)
  623. * Override with M92
  624. * X, Y, Z, E0 [, E1[, E2...]]
  625. */
  626. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
  627. /**
  628. * Default Max Feed Rate (mm/s)
  629. * Override with M203
  630. * X, Y, Z, E0 [, E1[, E2...]]
  631. */
  632. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  633. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  634. #if ENABLED(LIMITED_MAX_FR_EDITING)
  635. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  636. #endif
  637. /**
  638. * Default Max Acceleration (change/s) change = mm/s
  639. * (Maximum start speed for accelerated moves)
  640. * Override with M201
  641. * X, Y, Z, E0 [, E1[, E2...]]
  642. */
  643. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  644. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  645. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  646. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  647. #endif
  648. /**
  649. * Default Acceleration (change/s) change = mm/s
  650. * Override with M204
  651. *
  652. * M204 P Acceleration
  653. * M204 R Retract Acceleration
  654. * M204 T Travel Acceleration
  655. */
  656. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  657. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  658. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  659. /**
  660. * Default Jerk limits (mm/s)
  661. * Override with M205 X Y Z E
  662. *
  663. * "Jerk" specifies the minimum speed change that requires acceleration.
  664. * When changing speed and direction, if the difference is less than the
  665. * value set here, it may happen instantaneously.
  666. */
  667. //#define CLASSIC_JERK
  668. #if ENABLED(CLASSIC_JERK)
  669. #define DEFAULT_XJERK 10.0
  670. #define DEFAULT_YJERK 10.0
  671. #define DEFAULT_ZJERK 0.3
  672. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  673. #if ENABLED(LIMITED_JERK_EDITING)
  674. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  675. #endif
  676. #endif
  677. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  678. /**
  679. * Junction Deviation Factor
  680. *
  681. * See:
  682. * https://reprap.org/forum/read.php?1,739819
  683. * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  684. */
  685. #if DISABLED(CLASSIC_JERK)
  686. #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
  687. #endif
  688. /**
  689. * S-Curve Acceleration
  690. *
  691. * This option eliminates vibration during printing by fitting a Bézier
  692. * curve to move acceleration, producing much smoother direction changes.
  693. *
  694. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  695. */
  696. //#define S_CURVE_ACCELERATION
  697. //===========================================================================
  698. //============================= Z Probe Options =============================
  699. //===========================================================================
  700. // @section probes
  701. //
  702. // See http://marlinfw.org/docs/configuration/probes.html
  703. //
  704. /**
  705. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  706. *
  707. * Enable this option for a probe connected to the Z Min endstop pin.
  708. */
  709. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  710. /**
  711. * Z_MIN_PROBE_PIN
  712. *
  713. * Define this pin if the probe is not connected to Z_MIN_PIN.
  714. * If not defined the default pin for the selected MOTHERBOARD
  715. * will be used. Most of the time the default is what you want.
  716. *
  717. * - The simplest option is to use a free endstop connector.
  718. * - Use 5V for powered (usually inductive) sensors.
  719. *
  720. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  721. * - For simple switches connect...
  722. * - normally-closed switches to GND and D32.
  723. * - normally-open switches to 5V and D32.
  724. *
  725. */
  726. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  727. /**
  728. * Probe Type
  729. *
  730. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  731. * Activate one of these to use Auto Bed Leveling below.
  732. */
  733. /**
  734. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  735. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  736. * or (with LCD_BED_LEVELING) the LCD controller.
  737. */
  738. //#define PROBE_MANUALLY
  739. //#define MANUAL_PROBE_START_Z 0.2
  740. /**
  741. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  742. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  743. */
  744. //#define FIX_MOUNTED_PROBE
  745. /**
  746. * Z Servo Probe, such as an endstop switch on a rotating arm.
  747. */
  748. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  749. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  750. /**
  751. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  752. */
  753. //#define BLTOUCH
  754. /**
  755. * Touch-MI Probe by hotends.fr
  756. *
  757. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  758. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  759. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  760. *
  761. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  762. * and a minimum Z_HOMING_HEIGHT of 10.
  763. */
  764. //#define TOUCH_MI_PROBE
  765. #if ENABLED(TOUCH_MI_PROBE)
  766. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  767. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  768. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  769. #endif
  770. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  771. //#define SOLENOID_PROBE
  772. // A sled-mounted probe like those designed by Charles Bell.
  773. //#define Z_PROBE_SLED
  774. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  775. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  776. //#define RACK_AND_PINION_PROBE
  777. #if ENABLED(RACK_AND_PINION_PROBE)
  778. #define Z_PROBE_DEPLOY_X X_MIN_POS
  779. #define Z_PROBE_RETRACT_X X_MAX_POS
  780. #endif
  781. //
  782. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  783. //
  784. /**
  785. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  786. *
  787. * In the following example the X and Y offsets are both positive:
  788. *
  789. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  790. *
  791. * +-- BACK ---+
  792. * | |
  793. * L | (+) P | R <-- probe (20,20)
  794. * E | | I
  795. * F | (-) N (+) | G <-- nozzle (10,10)
  796. * T | | H
  797. * | (-) | T
  798. * | |
  799. * O-- FRONT --+
  800. * (0,0)
  801. *
  802. * Specify a Probe position as { X, Y, Z }
  803. */
  804. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  805. // Certain types of probes need to stay away from edges
  806. #define MIN_PROBE_EDGE 10
  807. // X and Y axis travel speed (mm/m) between probes
  808. #define XY_PROBE_SPEED 8000
  809. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  810. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  811. // Feedrate (mm/m) for the "accurate" probe of each point
  812. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  813. /**
  814. * Multiple Probing
  815. *
  816. * You may get improved results by probing 2 or more times.
  817. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  818. *
  819. * A total of 2 does fast/slow probes with a weighted average.
  820. * A total of 3 or more adds more slow probes, taking the average.
  821. */
  822. //#define MULTIPLE_PROBING 2
  823. //#define EXTRA_PROBING 1
  824. /**
  825. * Z probes require clearance when deploying, stowing, and moving between
  826. * probe points to avoid hitting the bed and other hardware.
  827. * Servo-mounted probes require extra space for the arm to rotate.
  828. * Inductive probes need space to keep from triggering early.
  829. *
  830. * Use these settings to specify the distance (mm) to raise the probe (or
  831. * lower the bed). The values set here apply over and above any (negative)
  832. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  833. * Only integer values >= 1 are valid here.
  834. *
  835. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  836. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  837. */
  838. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  839. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  840. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  841. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  842. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  843. // For M851 give a range for adjusting the Z probe offset
  844. #define Z_PROBE_OFFSET_RANGE_MIN -20
  845. #define Z_PROBE_OFFSET_RANGE_MAX 20
  846. // Enable the M48 repeatability test to test probe accuracy
  847. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  848. // Before deploy/stow pause for user confirmation
  849. //#define PAUSE_BEFORE_DEPLOY_STOW
  850. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  851. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  852. #endif
  853. /**
  854. * Enable one or more of the following if probing seems unreliable.
  855. * Heaters and/or fans can be disabled during probing to minimize electrical
  856. * noise. A delay can also be added to allow noise and vibration to settle.
  857. * These options are most useful for the BLTouch probe, but may also improve
  858. * readings with inductive probes and piezo sensors.
  859. */
  860. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  861. #if ENABLED(PROBING_HEATERS_OFF)
  862. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  863. #endif
  864. //#define PROBING_FANS_OFF // Turn fans off when probing
  865. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  866. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  867. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  868. // :{ 0:'Low', 1:'High' }
  869. #define X_ENABLE_ON 0
  870. #define Y_ENABLE_ON 0
  871. #define Z_ENABLE_ON 0
  872. #define E_ENABLE_ON 0 // For all extruders
  873. // Disables axis stepper immediately when it's not being used.
  874. // WARNING: When motors turn off there is a chance of losing position accuracy!
  875. #define DISABLE_X false
  876. #define DISABLE_Y false
  877. #define DISABLE_Z false
  878. // Warn on display about possibly reduced accuracy
  879. //#define DISABLE_REDUCED_ACCURACY_WARNING
  880. // @section extruder
  881. #define DISABLE_E false // For all extruders
  882. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  883. // @section machine
  884. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  885. #define INVERT_X_DIR false
  886. #define INVERT_Y_DIR true
  887. #define INVERT_Z_DIR false
  888. // @section extruder
  889. // For direct drive extruder v9 set to true, for geared extruder set to false.
  890. #define INVERT_E0_DIR false
  891. #define INVERT_E1_DIR false
  892. #define INVERT_E2_DIR false
  893. #define INVERT_E3_DIR false
  894. #define INVERT_E4_DIR false
  895. #define INVERT_E5_DIR false
  896. // @section homing
  897. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  898. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  899. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  900. // Be sure you have this distance over your Z_MAX_POS in case.
  901. // Direction of endstops when homing; 1=MAX, -1=MIN
  902. // :[-1,1]
  903. #define X_HOME_DIR -1
  904. #define Y_HOME_DIR -1
  905. #define Z_HOME_DIR -1
  906. // @section machine
  907. // The size of the print bed
  908. #define X_BED_SIZE 200
  909. #define Y_BED_SIZE 200
  910. // Travel limits (mm) after homing, corresponding to endstop positions.
  911. #define X_MIN_POS 0
  912. #define Y_MIN_POS 0
  913. #define Z_MIN_POS 0
  914. #define X_MAX_POS X_BED_SIZE
  915. #define Y_MAX_POS Y_BED_SIZE
  916. #define Z_MAX_POS 200
  917. /**
  918. * Software Endstops
  919. *
  920. * - Prevent moves outside the set machine bounds.
  921. * - Individual axes can be disabled, if desired.
  922. * - X and Y only apply to Cartesian robots.
  923. * - Use 'M211' to set software endstops on/off or report current state
  924. */
  925. // Min software endstops constrain movement within minimum coordinate bounds
  926. #define MIN_SOFTWARE_ENDSTOPS
  927. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  928. #define MIN_SOFTWARE_ENDSTOP_X
  929. #define MIN_SOFTWARE_ENDSTOP_Y
  930. #define MIN_SOFTWARE_ENDSTOP_Z
  931. #endif
  932. // Max software endstops constrain movement within maximum coordinate bounds
  933. #define MAX_SOFTWARE_ENDSTOPS
  934. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  935. #define MAX_SOFTWARE_ENDSTOP_X
  936. #define MAX_SOFTWARE_ENDSTOP_Y
  937. #define MAX_SOFTWARE_ENDSTOP_Z
  938. #endif
  939. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  940. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  941. #endif
  942. /**
  943. * Filament Runout Sensors
  944. * Mechanical or opto endstops are used to check for the presence of filament.
  945. *
  946. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  947. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  948. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  949. */
  950. //#define FILAMENT_RUNOUT_SENSOR
  951. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  952. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  953. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
  954. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  955. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  956. // Set one or more commands to execute on filament runout.
  957. // (After 'M412 H' Marlin will ask the host to handle the process.)
  958. #define FILAMENT_RUNOUT_SCRIPT "M600"
  959. // After a runout is detected, continue printing this length of filament
  960. // before executing the runout script. Useful for a sensor at the end of
  961. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  962. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  963. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  964. // Enable this option to use an encoder disc that toggles the runout pin
  965. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  966. // large enough to avoid false positives.)
  967. //#define FILAMENT_MOTION_SENSOR
  968. #endif
  969. #endif
  970. //===========================================================================
  971. //=============================== Bed Leveling ==============================
  972. //===========================================================================
  973. // @section calibrate
  974. /**
  975. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  976. * and behavior of G29 will change depending on your selection.
  977. *
  978. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  979. *
  980. * - AUTO_BED_LEVELING_3POINT
  981. * Probe 3 arbitrary points on the bed (that aren't collinear)
  982. * You specify the XY coordinates of all 3 points.
  983. * The result is a single tilted plane. Best for a flat bed.
  984. *
  985. * - AUTO_BED_LEVELING_LINEAR
  986. * Probe several points in a grid.
  987. * You specify the rectangle and the density of sample points.
  988. * The result is a single tilted plane. Best for a flat bed.
  989. *
  990. * - AUTO_BED_LEVELING_BILINEAR
  991. * Probe several points in a grid.
  992. * You specify the rectangle and the density of sample points.
  993. * The result is a mesh, best for large or uneven beds.
  994. *
  995. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  996. * A comprehensive bed leveling system combining the features and benefits
  997. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  998. * Validation and Mesh Editing systems.
  999. *
  1000. * - MESH_BED_LEVELING
  1001. * Probe a grid manually
  1002. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1003. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1004. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1005. * With an LCD controller the process is guided step-by-step.
  1006. */
  1007. //#define AUTO_BED_LEVELING_3POINT
  1008. //#define AUTO_BED_LEVELING_LINEAR
  1009. //#define AUTO_BED_LEVELING_BILINEAR
  1010. //#define AUTO_BED_LEVELING_UBL
  1011. //#define MESH_BED_LEVELING
  1012. /**
  1013. * Normally G28 leaves leveling disabled on completion. Enable
  1014. * this option to have G28 restore the prior leveling state.
  1015. */
  1016. //#define RESTORE_LEVELING_AFTER_G28
  1017. /**
  1018. * Enable detailed logging of G28, G29, M48, etc.
  1019. * Turn on with the command 'M111 S32'.
  1020. * NOTE: Requires a lot of PROGMEM!
  1021. */
  1022. //#define DEBUG_LEVELING_FEATURE
  1023. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1024. // Gradually reduce leveling correction until a set height is reached,
  1025. // at which point movement will be level to the machine's XY plane.
  1026. // The height can be set with M420 Z<height>
  1027. #define ENABLE_LEVELING_FADE_HEIGHT
  1028. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1029. // split up moves into short segments like a Delta. This follows the
  1030. // contours of the bed more closely than edge-to-edge straight moves.
  1031. #define SEGMENT_LEVELED_MOVES
  1032. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1033. /**
  1034. * Enable the G26 Mesh Validation Pattern tool.
  1035. */
  1036. //#define G26_MESH_VALIDATION
  1037. #if ENABLED(G26_MESH_VALIDATION)
  1038. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1039. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1040. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1041. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1042. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1043. #endif
  1044. #endif
  1045. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1046. // Set the number of grid points per dimension.
  1047. #define GRID_MAX_POINTS_X 3
  1048. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1049. // Probe along the Y axis, advancing X after each column
  1050. //#define PROBE_Y_FIRST
  1051. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1052. // Beyond the probed grid, continue the implied tilt?
  1053. // Default is to maintain the height of the nearest edge.
  1054. //#define EXTRAPOLATE_BEYOND_GRID
  1055. //
  1056. // Experimental Subdivision of the grid by Catmull-Rom method.
  1057. // Synthesizes intermediate points to produce a more detailed mesh.
  1058. //
  1059. //#define ABL_BILINEAR_SUBDIVISION
  1060. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1061. // Number of subdivisions between probe points
  1062. #define BILINEAR_SUBDIVISIONS 3
  1063. #endif
  1064. #endif
  1065. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1066. //===========================================================================
  1067. //========================= Unified Bed Leveling ============================
  1068. //===========================================================================
  1069. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1070. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1071. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1072. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1073. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1074. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1075. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1076. // as the Z-Height correction value.
  1077. #elif ENABLED(MESH_BED_LEVELING)
  1078. //===========================================================================
  1079. //=================================== Mesh ==================================
  1080. //===========================================================================
  1081. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1082. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1083. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1084. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1085. #endif // BED_LEVELING
  1086. /**
  1087. * Add a bed leveling sub-menu for ABL or MBL.
  1088. * Include a guided procedure if manual probing is enabled.
  1089. */
  1090. //#define LCD_BED_LEVELING
  1091. #if ENABLED(LCD_BED_LEVELING)
  1092. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1093. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1094. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1095. #endif
  1096. // Add a menu item to move between bed corners for manual bed adjustment
  1097. //#define LEVEL_BED_CORNERS
  1098. #if ENABLED(LEVEL_BED_CORNERS)
  1099. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1100. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
  1101. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1102. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1103. #endif
  1104. /**
  1105. * Commands to execute at the end of G29 probing.
  1106. * Useful to retract or move the Z probe out of the way.
  1107. */
  1108. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1109. // @section homing
  1110. // The center of the bed is at (X=0, Y=0)
  1111. //#define BED_CENTER_AT_0_0
  1112. // Manually set the home position. Leave these undefined for automatic settings.
  1113. // For DELTA this is the top-center of the Cartesian print volume.
  1114. //#define MANUAL_X_HOME_POS 0
  1115. //#define MANUAL_Y_HOME_POS 0
  1116. //#define MANUAL_Z_HOME_POS 0
  1117. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1118. //
  1119. // With this feature enabled:
  1120. //
  1121. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1122. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1123. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1124. // - Prevent Z homing when the Z probe is outside bed area.
  1125. //
  1126. //#define Z_SAFE_HOMING
  1127. #if ENABLED(Z_SAFE_HOMING)
  1128. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1129. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1130. #endif
  1131. // Homing speeds (mm/m)
  1132. #define HOMING_FEEDRATE_XY (50*60)
  1133. #define HOMING_FEEDRATE_Z (4*60)
  1134. // Validate that endstops are triggered on homing moves
  1135. #define VALIDATE_HOMING_ENDSTOPS
  1136. // @section calibrate
  1137. /**
  1138. * Bed Skew Compensation
  1139. *
  1140. * This feature corrects for misalignment in the XYZ axes.
  1141. *
  1142. * Take the following steps to get the bed skew in the XY plane:
  1143. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1144. * 2. For XY_DIAG_AC measure the diagonal A to C
  1145. * 3. For XY_DIAG_BD measure the diagonal B to D
  1146. * 4. For XY_SIDE_AD measure the edge A to D
  1147. *
  1148. * Marlin automatically computes skew factors from these measurements.
  1149. * Skew factors may also be computed and set manually:
  1150. *
  1151. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1152. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1153. *
  1154. * If desired, follow the same procedure for XZ and YZ.
  1155. * Use these diagrams for reference:
  1156. *
  1157. * Y Z Z
  1158. * ^ B-------C ^ B-------C ^ B-------C
  1159. * | / / | / / | / /
  1160. * | / / | / / | / /
  1161. * | A-------D | A-------D | A-------D
  1162. * +-------------->X +-------------->X +-------------->Y
  1163. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1164. */
  1165. //#define SKEW_CORRECTION
  1166. #if ENABLED(SKEW_CORRECTION)
  1167. // Input all length measurements here:
  1168. #define XY_DIAG_AC 282.8427124746
  1169. #define XY_DIAG_BD 282.8427124746
  1170. #define XY_SIDE_AD 200
  1171. // Or, set the default skew factors directly here
  1172. // to override the above measurements:
  1173. #define XY_SKEW_FACTOR 0.0
  1174. //#define SKEW_CORRECTION_FOR_Z
  1175. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1176. #define XZ_DIAG_AC 282.8427124746
  1177. #define XZ_DIAG_BD 282.8427124746
  1178. #define YZ_DIAG_AC 282.8427124746
  1179. #define YZ_DIAG_BD 282.8427124746
  1180. #define YZ_SIDE_AD 200
  1181. #define XZ_SKEW_FACTOR 0.0
  1182. #define YZ_SKEW_FACTOR 0.0
  1183. #endif
  1184. // Enable this option for M852 to set skew at runtime
  1185. //#define SKEW_CORRECTION_GCODE
  1186. #endif
  1187. //=============================================================================
  1188. //============================= Additional Features ===========================
  1189. //=============================================================================
  1190. // @section extras
  1191. /**
  1192. * EEPROM
  1193. *
  1194. * Persistent storage to preserve configurable settings across reboots.
  1195. *
  1196. * M500 - Store settings to EEPROM.
  1197. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1198. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1199. */
  1200. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1201. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1202. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1203. #if ENABLED(EEPROM_SETTINGS)
  1204. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1205. #endif
  1206. //
  1207. // Host Keepalive
  1208. //
  1209. // When enabled Marlin will send a busy status message to the host
  1210. // every couple of seconds when it can't accept commands.
  1211. //
  1212. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1213. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1214. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1215. //
  1216. // M100 Free Memory Watcher
  1217. //
  1218. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1219. //
  1220. // G20/G21 Inch mode support
  1221. //
  1222. //#define INCH_MODE_SUPPORT
  1223. //
  1224. // M149 Set temperature units support
  1225. //
  1226. //#define TEMPERATURE_UNITS_SUPPORT
  1227. // @section temperature
  1228. // Preheat Constants
  1229. #define PREHEAT_1_LABEL "PLA"
  1230. #define PREHEAT_1_TEMP_HOTEND 180
  1231. #define PREHEAT_1_TEMP_BED 70
  1232. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1233. #define PREHEAT_2_LABEL "ABS"
  1234. #define PREHEAT_2_TEMP_HOTEND 240
  1235. #define PREHEAT_2_TEMP_BED 110
  1236. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1237. /**
  1238. * Nozzle Park
  1239. *
  1240. * Park the nozzle at the given XYZ position on idle or G27.
  1241. *
  1242. * The "P" parameter controls the action applied to the Z axis:
  1243. *
  1244. * P0 (Default) If Z is below park Z raise the nozzle.
  1245. * P1 Raise the nozzle always to Z-park height.
  1246. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1247. */
  1248. //#define NOZZLE_PARK_FEATURE
  1249. #if ENABLED(NOZZLE_PARK_FEATURE)
  1250. // Specify a park position as { X, Y, Z_raise }
  1251. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1252. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1253. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1254. #endif
  1255. /**
  1256. * Clean Nozzle Feature -- EXPERIMENTAL
  1257. *
  1258. * Adds the G12 command to perform a nozzle cleaning process.
  1259. *
  1260. * Parameters:
  1261. * P Pattern
  1262. * S Strokes / Repetitions
  1263. * T Triangles (P1 only)
  1264. *
  1265. * Patterns:
  1266. * P0 Straight line (default). This process requires a sponge type material
  1267. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1268. * between the start / end points.
  1269. *
  1270. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1271. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1272. * Zig-zags are done in whichever is the narrower dimension.
  1273. * For example, "G12 P1 S1 T3" will execute:
  1274. *
  1275. * --
  1276. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1277. * | | / \ / \ / \ |
  1278. * A | | / \ / \ / \ |
  1279. * | | / \ / \ / \ |
  1280. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1281. * -- +--------------------------------+
  1282. * |________|_________|_________|
  1283. * T1 T2 T3
  1284. *
  1285. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1286. * "R" specifies the radius. "S" specifies the stroke count.
  1287. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1288. *
  1289. * Caveats: The ending Z should be the same as starting Z.
  1290. * Attention: EXPERIMENTAL. G-code arguments may change.
  1291. *
  1292. */
  1293. //#define NOZZLE_CLEAN_FEATURE
  1294. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1295. // Default number of pattern repetitions
  1296. #define NOZZLE_CLEAN_STROKES 12
  1297. // Default number of triangles
  1298. #define NOZZLE_CLEAN_TRIANGLES 3
  1299. // Specify positions as { X, Y, Z }
  1300. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1) }
  1301. #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) }
  1302. // Circular pattern radius
  1303. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1304. // Circular pattern circle fragments number
  1305. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1306. // Middle point of circle
  1307. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1308. // Move the nozzle to the initial position after cleaning
  1309. #define NOZZLE_CLEAN_GOBACK
  1310. // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
  1311. //#define NOZZLE_CLEAN_NO_Z
  1312. #endif
  1313. /**
  1314. * Print Job Timer
  1315. *
  1316. * Automatically start and stop the print job timer on M104/M109/M190.
  1317. *
  1318. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1319. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1320. * M190 (bed, wait) - high temp = start timer, low temp = none
  1321. *
  1322. * The timer can also be controlled with the following commands:
  1323. *
  1324. * M75 - Start the print job timer
  1325. * M76 - Pause the print job timer
  1326. * M77 - Stop the print job timer
  1327. */
  1328. #define PRINTJOB_TIMER_AUTOSTART
  1329. /**
  1330. * Print Counter
  1331. *
  1332. * Track statistical data such as:
  1333. *
  1334. * - Total print jobs
  1335. * - Total successful print jobs
  1336. * - Total failed print jobs
  1337. * - Total time printing
  1338. *
  1339. * View the current statistics with M78.
  1340. */
  1341. //#define PRINTCOUNTER
  1342. //=============================================================================
  1343. //============================= LCD and SD support ============================
  1344. //=============================================================================
  1345. // @section lcd
  1346. /**
  1347. * LCD LANGUAGE
  1348. *
  1349. * Select the language to display on the LCD. These languages are available:
  1350. *
  1351. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
  1352. * ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1353. *
  1354. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1355. */
  1356. #define LCD_LANGUAGE en
  1357. /**
  1358. * LCD Character Set
  1359. *
  1360. * Note: This option is NOT applicable to Graphical Displays.
  1361. *
  1362. * All character-based LCDs provide ASCII plus one of these
  1363. * language extensions:
  1364. *
  1365. * - JAPANESE ... the most common
  1366. * - WESTERN ... with more accented characters
  1367. * - CYRILLIC ... for the Russian language
  1368. *
  1369. * To determine the language extension installed on your controller:
  1370. *
  1371. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1372. * - Click the controller to view the LCD menu
  1373. * - The LCD will display Japanese, Western, or Cyrillic text
  1374. *
  1375. * See http://marlinfw.org/docs/development/lcd_language.html
  1376. *
  1377. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1378. */
  1379. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1380. /**
  1381. * Info Screen Style (0:Classic, 1:Prusa)
  1382. *
  1383. * :[0:'Classic', 1:'Prusa']
  1384. */
  1385. #define LCD_INFO_SCREEN_STYLE 0
  1386. /**
  1387. * SD CARD
  1388. *
  1389. * SD Card support is disabled by default. If your controller has an SD slot,
  1390. * you must uncomment the following option or it won't work.
  1391. *
  1392. */
  1393. //#define SDSUPPORT
  1394. /**
  1395. * SD CARD: SPI SPEED
  1396. *
  1397. * Enable one of the following items for a slower SPI transfer speed.
  1398. * This may be required to resolve "volume init" errors.
  1399. */
  1400. //#define SPI_SPEED SPI_HALF_SPEED
  1401. //#define SPI_SPEED SPI_QUARTER_SPEED
  1402. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1403. /**
  1404. * SD CARD: ENABLE CRC
  1405. *
  1406. * Use CRC checks and retries on the SD communication.
  1407. */
  1408. //#define SD_CHECK_AND_RETRY
  1409. /**
  1410. * LCD Menu Items
  1411. *
  1412. * Disable all menus and only display the Status Screen, or
  1413. * just remove some extraneous menu items to recover space.
  1414. */
  1415. //#define NO_LCD_MENUS
  1416. //#define SLIM_LCD_MENUS
  1417. //
  1418. // ENCODER SETTINGS
  1419. //
  1420. // This option overrides the default number of encoder pulses needed to
  1421. // produce one step. Should be increased for high-resolution encoders.
  1422. //
  1423. //#define ENCODER_PULSES_PER_STEP 4
  1424. //
  1425. // Use this option to override the number of step signals required to
  1426. // move between next/prev menu items.
  1427. //
  1428. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1429. /**
  1430. * Encoder Direction Options
  1431. *
  1432. * Test your encoder's behavior first with both options disabled.
  1433. *
  1434. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1435. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1436. * Reversed Value Editing only? Enable BOTH options.
  1437. */
  1438. //
  1439. // This option reverses the encoder direction everywhere.
  1440. //
  1441. // Set this option if CLOCKWISE causes values to DECREASE
  1442. //
  1443. //#define REVERSE_ENCODER_DIRECTION
  1444. //
  1445. // This option reverses the encoder direction for navigating LCD menus.
  1446. //
  1447. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1448. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1449. //
  1450. //#define REVERSE_MENU_DIRECTION
  1451. //
  1452. // This option reverses the encoder direction for Select Screen.
  1453. //
  1454. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1455. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1456. //
  1457. //#define REVERSE_SELECT_DIRECTION
  1458. //
  1459. // Individual Axis Homing
  1460. //
  1461. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1462. //
  1463. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1464. //
  1465. // SPEAKER/BUZZER
  1466. //
  1467. // If you have a speaker that can produce tones, enable it here.
  1468. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1469. //
  1470. //#define SPEAKER
  1471. //
  1472. // The duration and frequency for the UI feedback sound.
  1473. // Set these to 0 to disable audio feedback in the LCD menus.
  1474. //
  1475. // Note: Test audio output with the G-Code:
  1476. // M300 S<frequency Hz> P<duration ms>
  1477. //
  1478. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1479. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1480. //=============================================================================
  1481. //======================== LCD / Controller Selection =========================
  1482. //======================== (Character-based LCDs) =========================
  1483. //=============================================================================
  1484. //
  1485. // RepRapDiscount Smart Controller.
  1486. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1487. //
  1488. // Note: Usually sold with a white PCB.
  1489. //
  1490. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1491. //
  1492. // Original RADDS LCD Display+Encoder+SDCardReader
  1493. // http://doku.radds.org/dokumentation/lcd-display/
  1494. //
  1495. //#define RADDS_DISPLAY
  1496. //
  1497. // ULTIMAKER Controller.
  1498. //
  1499. //#define ULTIMAKERCONTROLLER
  1500. //
  1501. // ULTIPANEL as seen on Thingiverse.
  1502. //
  1503. //#define ULTIPANEL
  1504. //
  1505. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1506. // http://reprap.org/wiki/PanelOne
  1507. //
  1508. //#define PANEL_ONE
  1509. //
  1510. // GADGETS3D G3D LCD/SD Controller
  1511. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1512. //
  1513. // Note: Usually sold with a blue PCB.
  1514. //
  1515. //#define G3D_PANEL
  1516. //
  1517. // RigidBot Panel V1.0
  1518. // http://www.inventapart.com/
  1519. //
  1520. //#define RIGIDBOT_PANEL
  1521. //
  1522. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1523. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1524. //
  1525. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1526. //
  1527. // ANET and Tronxy 20x4 Controller
  1528. //
  1529. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1530. // This LCD is known to be susceptible to electrical interference
  1531. // which scrambles the display. Pressing any button clears it up.
  1532. // This is a LCD2004 display with 5 analog buttons.
  1533. //
  1534. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1535. //
  1536. //#define ULTRA_LCD
  1537. //=============================================================================
  1538. //======================== LCD / Controller Selection =========================
  1539. //===================== (I2C and Shift-Register LCDs) =====================
  1540. //=============================================================================
  1541. //
  1542. // CONTROLLER TYPE: I2C
  1543. //
  1544. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1545. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1546. //
  1547. //
  1548. // Elefu RA Board Control Panel
  1549. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1550. //
  1551. //#define RA_CONTROL_PANEL
  1552. //
  1553. // Sainsmart (YwRobot) LCD Displays
  1554. //
  1555. // These require F.Malpartida's LiquidCrystal_I2C library
  1556. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1557. //
  1558. //#define LCD_SAINSMART_I2C_1602
  1559. //#define LCD_SAINSMART_I2C_2004
  1560. //
  1561. // Generic LCM1602 LCD adapter
  1562. //
  1563. //#define LCM1602
  1564. //
  1565. // PANELOLU2 LCD with status LEDs,
  1566. // separate encoder and click inputs.
  1567. //
  1568. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1569. // For more info: https://github.com/lincomatic/LiquidTWI2
  1570. //
  1571. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1572. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1573. //
  1574. //#define LCD_I2C_PANELOLU2
  1575. //
  1576. // Panucatt VIKI LCD with status LEDs,
  1577. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1578. //
  1579. //#define LCD_I2C_VIKI
  1580. //
  1581. // CONTROLLER TYPE: Shift register panels
  1582. //
  1583. //
  1584. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1585. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1586. //
  1587. //#define SAV_3DLCD
  1588. //
  1589. // 3-wire SR LCD with strobe using 74HC4094
  1590. // https://github.com/mikeshub/SailfishLCD
  1591. // Uses the code directly from Sailfish
  1592. //
  1593. //#define FF_INTERFACEBOARD
  1594. //=============================================================================
  1595. //======================= LCD / Controller Selection =======================
  1596. //========================= (Graphical LCDs) ========================
  1597. //=============================================================================
  1598. //
  1599. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1600. //
  1601. // IMPORTANT: The U8glib library is required for Graphical Display!
  1602. // https://github.com/olikraus/U8glib_Arduino
  1603. //
  1604. //
  1605. // RepRapDiscount FULL GRAPHIC Smart Controller
  1606. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1607. //
  1608. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1609. //
  1610. // ReprapWorld Graphical LCD
  1611. // https://reprapworld.com/?products_details&products_id/1218
  1612. //
  1613. //#define REPRAPWORLD_GRAPHICAL_LCD
  1614. //
  1615. // Activate one of these if you have a Panucatt Devices
  1616. // Viki 2.0 or mini Viki with Graphic LCD
  1617. // http://panucatt.com
  1618. //
  1619. //#define VIKI2
  1620. //#define miniVIKI
  1621. //
  1622. // MakerLab Mini Panel with graphic
  1623. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1624. //
  1625. //#define MINIPANEL
  1626. //
  1627. // MaKr3d Makr-Panel with graphic controller and SD support.
  1628. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1629. //
  1630. //#define MAKRPANEL
  1631. //
  1632. // Adafruit ST7565 Full Graphic Controller.
  1633. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1634. //
  1635. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1636. //
  1637. // BQ LCD Smart Controller shipped by
  1638. // default with the BQ Hephestos 2 and Witbox 2.
  1639. //
  1640. //#define BQ_LCD_SMART_CONTROLLER
  1641. //
  1642. // Cartesio UI
  1643. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1644. //
  1645. //#define CARTESIO_UI
  1646. //
  1647. // LCD for Melzi Card with Graphical LCD
  1648. //
  1649. //#define LCD_FOR_MELZI
  1650. //
  1651. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1652. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1653. //
  1654. //#define ULTI_CONTROLLER
  1655. //
  1656. // MKS MINI12864 with graphic controller and SD support
  1657. // https://reprap.org/wiki/MKS_MINI_12864
  1658. //
  1659. //#define MKS_MINI_12864
  1660. //
  1661. // FYSETC variant of the MINI12864 graphic controller with SD support
  1662. // https://wiki.fysetc.com/Mini12864_Panel/
  1663. //
  1664. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1665. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1666. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1667. //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight
  1668. //
  1669. // Factory display for Creality CR-10
  1670. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1671. //
  1672. // This is RAMPS-compatible using a single 10-pin connector.
  1673. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1674. //
  1675. //#define CR10_STOCKDISPLAY
  1676. //
  1677. // ANET and Tronxy Graphical Controller
  1678. //
  1679. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1680. // A clone of the RepRapDiscount full graphics display but with
  1681. // different pins/wiring (see pins_ANET_10.h).
  1682. //
  1683. //#define ANET_FULL_GRAPHICS_LCD
  1684. //
  1685. // AZSMZ 12864 LCD with SD
  1686. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1687. //
  1688. //#define AZSMZ_12864
  1689. //
  1690. // Silvergate GLCD controller
  1691. // http://github.com/android444/Silvergate
  1692. //
  1693. //#define SILVER_GATE_GLCD_CONTROLLER
  1694. //=============================================================================
  1695. //============================== OLED Displays ==============================
  1696. //=============================================================================
  1697. //
  1698. // SSD1306 OLED full graphics generic display
  1699. //
  1700. //#define U8GLIB_SSD1306
  1701. //
  1702. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1703. //
  1704. //#define SAV_3DGLCD
  1705. #if ENABLED(SAV_3DGLCD)
  1706. #define U8GLIB_SSD1306
  1707. //#define U8GLIB_SH1106
  1708. #endif
  1709. //
  1710. // TinyBoy2 128x64 OLED / Encoder Panel
  1711. //
  1712. //#define OLED_PANEL_TINYBOY2
  1713. //
  1714. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1715. // http://reprap.org/wiki/MKS_12864OLED
  1716. //
  1717. // Tiny, but very sharp OLED display
  1718. //
  1719. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1720. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1721. //
  1722. // Einstart S OLED SSD1306
  1723. //
  1724. //#define U8GLIB_SH1106_EINSTART
  1725. //
  1726. // Overlord OLED display/controller with i2c buzzer and LEDs
  1727. //
  1728. //#define OVERLORD_OLED
  1729. //=============================================================================
  1730. //========================== Extensible UI Displays ===========================
  1731. //=============================================================================
  1732. //
  1733. // DGUS Touch Display with DWIN OS
  1734. //
  1735. //#define DGUS_LCD
  1736. //
  1737. // Touch-screen LCD for Malyan M200 printers
  1738. //
  1739. //#define MALYAN_LCD
  1740. //
  1741. // Touch UI for FTDI EVE (FT800/FT810) displays
  1742. // See Configuration_adv.h for all configuration options.
  1743. //
  1744. //#define TOUCH_UI_FTDI_EVE
  1745. //
  1746. // Third-party or vendor-customized controller interfaces.
  1747. // Sources should be installed in 'src/lcd/extensible_ui'.
  1748. //
  1749. //#define EXTENSIBLE_UI
  1750. //=============================================================================
  1751. //=============================== Graphical TFTs ==============================
  1752. //=============================================================================
  1753. //
  1754. // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
  1755. //
  1756. //#define FSMC_GRAPHICAL_TFT
  1757. //=============================================================================
  1758. //============================ Other Controllers ============================
  1759. //=============================================================================
  1760. //
  1761. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  1762. //
  1763. //#define TOUCH_BUTTONS
  1764. #if ENABLED(TOUCH_BUTTONS)
  1765. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  1766. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  1767. #define XPT2046_X_CALIBRATION 12316
  1768. #define XPT2046_Y_CALIBRATION -8981
  1769. #define XPT2046_X_OFFSET -43
  1770. #define XPT2046_Y_OFFSET 257
  1771. #endif
  1772. //
  1773. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1774. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1775. //
  1776. //#define REPRAPWORLD_KEYPAD
  1777. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  1778. //=============================================================================
  1779. //=============================== Extra Features ==============================
  1780. //=============================================================================
  1781. // @section extras
  1782. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1783. //#define FAST_PWM_FAN
  1784. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1785. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1786. // is too low, you should also increment SOFT_PWM_SCALE.
  1787. //#define FAN_SOFT_PWM
  1788. // Incrementing this by 1 will double the software PWM frequency,
  1789. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1790. // However, control resolution will be halved for each increment;
  1791. // at zero value, there are 128 effective control positions.
  1792. // :[0,1,2,3,4,5,6,7]
  1793. #define SOFT_PWM_SCALE 0
  1794. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1795. // be used to mitigate the associated resolution loss. If enabled,
  1796. // some of the PWM cycles are stretched so on average the desired
  1797. // duty cycle is attained.
  1798. //#define SOFT_PWM_DITHER
  1799. // Temperature status LEDs that display the hotend and bed temperature.
  1800. // If all hotends, bed temperature, and target temperature are under 54C
  1801. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1802. //#define TEMP_STAT_LEDS
  1803. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1804. //#define SF_ARC_FIX
  1805. // Support for the BariCUDA Paste Extruder
  1806. //#define BARICUDA
  1807. // Support for BlinkM/CyzRgb
  1808. //#define BLINKM
  1809. // Support for PCA9632 PWM LED driver
  1810. //#define PCA9632
  1811. // Support for PCA9533 PWM LED driver
  1812. // https://github.com/mikeshub/SailfishRGB_LED
  1813. //#define PCA9533
  1814. /**
  1815. * RGB LED / LED Strip Control
  1816. *
  1817. * Enable support for an RGB LED connected to 5V digital pins, or
  1818. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1819. *
  1820. * Adds the M150 command to set the LED (or LED strip) color.
  1821. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1822. * luminance values can be set from 0 to 255.
  1823. * For Neopixel LED an overall brightness parameter is also available.
  1824. *
  1825. * *** CAUTION ***
  1826. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1827. * as the Arduino cannot handle the current the LEDs will require.
  1828. * Failure to follow this precaution can destroy your Arduino!
  1829. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1830. * more current than the Arduino 5V linear regulator can produce.
  1831. * *** CAUTION ***
  1832. *
  1833. * LED Type. Enable only one of the following two options.
  1834. *
  1835. */
  1836. //#define RGB_LED
  1837. //#define RGBW_LED
  1838. #if EITHER(RGB_LED, RGBW_LED)
  1839. //#define RGB_LED_R_PIN 34
  1840. //#define RGB_LED_G_PIN 43
  1841. //#define RGB_LED_B_PIN 35
  1842. //#define RGB_LED_W_PIN -1
  1843. #endif
  1844. // Support for Adafruit Neopixel LED driver
  1845. //#define NEOPIXEL_LED
  1846. #if ENABLED(NEOPIXEL_LED)
  1847. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1848. #define NEOPIXEL_PIN 4 // LED driving pin
  1849. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  1850. //#define NEOPIXEL2_PIN 5
  1851. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
  1852. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1853. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1854. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1855. // Use a single Neopixel LED for static (background) lighting
  1856. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  1857. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  1858. #endif
  1859. /**
  1860. * Printer Event LEDs
  1861. *
  1862. * During printing, the LEDs will reflect the printer status:
  1863. *
  1864. * - Gradually change from blue to violet as the heated bed gets to target temp
  1865. * - Gradually change from violet to red as the hotend gets to temperature
  1866. * - Change to white to illuminate work surface
  1867. * - Change to green once print has finished
  1868. * - Turn off after the print has finished and the user has pushed a button
  1869. */
  1870. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  1871. #define PRINTER_EVENT_LEDS
  1872. #endif
  1873. /**
  1874. * R/C SERVO support
  1875. * Sponsored by TrinityLabs, Reworked by codexmas
  1876. */
  1877. /**
  1878. * Number of servos
  1879. *
  1880. * For some servo-related options NUM_SERVOS will be set automatically.
  1881. * Set this manually if there are extra servos needing manual control.
  1882. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1883. */
  1884. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1885. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  1886. // 300ms is a good value but you can try less delay.
  1887. // If the servo can't reach the requested position, increase it.
  1888. #define SERVO_DELAY { 300 }
  1889. // Only power servos during movement, otherwise leave off to prevent jitter
  1890. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1891. // Allow servo angle to be edited and saved to EEPROM
  1892. //#define EDITABLE_SERVO_ANGLES