123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <https://www.gnu.org/licenses/>.
- *
- */
- #pragma once
-
- #ifndef BOARD_INFO_NAME
- #define BOARD_INFO_NAME "FYSETC SPIDER"
- #endif
- #ifndef DEFAULT_MACHINE_NAME
- #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
- #endif
-
- //
- // EEPROM Emulation
- //
- #if NO_EEPROM_SELECTED
- #undef NO_EEPROM_SELECTED
- //#define FLASH_EEPROM_EMULATION
- //#define SRAM_EEPROM_EMULATION
- #define I2C_EEPROM
- #endif
-
- #if ENABLED(I2C_EEPROM)
- #define MARLIN_EEPROM_SIZE 0x1000 // 4K
- #endif
-
- //
- // Steppers
- //
- #define X2_STEP_PIN PD12
- #define X2_DIR_PIN PC4
- #define X2_ENABLE_PIN PE8
- #define X2_CS_PIN PA15
-
- #define Z2_STEP_PIN PE1
- #define Z2_DIR_PIN PE0
- #define Z2_ENABLE_PIN PC5
- #define Z2_CS_PIN PD11
-
- //
- // Heaters / Fans
- //
- #define HEATER_0_PIN PB15
- #define HEATER_1_PIN PC8
- #define HEATER_2_PIN PB3
- #define HEATER_BED_PIN PB4
-
- //
- // Steppers
- //
- #define X_ENABLE_PIN PE9
-
- //
- // Servos
- // Z_MAX_PIN only works in input mode
- //
- #define SERVO0_PIN PA2
-
- #if HAS_TMC_UART
- #define X_SERIAL_TX_PIN PE7
- #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
-
- #define X2_SERIAL_TX_PIN PA15
- #define X2_SERIAL_RX_PIN X2_SERIAL_TX_PIN
-
- #define Y_SERIAL_TX_PIN PE15
- #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
-
- #define Z_SERIAL_TX_PIN PD10
- #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
-
- #define Z2_SERIAL_TX_PIN PD11
- #define Z2_SERIAL_RX_PIN Z2_SERIAL_TX_PIN
-
- #define E0_SERIAL_TX_PIN PD7
- #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
-
- #define E1_SERIAL_TX_PIN PC14
- #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN
-
- #define E2_SERIAL_TX_PIN PC15
- #define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN
- #endif
-
- //
- // Software SPI pins for TMC2130 stepper drivers
- //
- #define TMC_USE_SW_SPI
- #if ENABLED(TMC_USE_SW_SPI)
- #ifndef TMC_SW_MOSI
- #define TMC_SW_MOSI PE14
- #endif
- #ifndef TMC_SW_MISO
- #define TMC_SW_MISO PE13
- #endif
- #ifndef TMC_SW_SCK
- #define TMC_SW_SCK PE12
- #endif
- #endif
-
- #if HOTENDS > 3 || E_STEPPERS > 3
- #error "FYSETC SPIDER supports up to 3 hotends / E steppers."
- #else
- #include "pins_FYSETC_S6.h"
- #endif
|