My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration_adv.h 44KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration_adv.h
  24. *
  25. * Advanced settings.
  26. * Only change these if you know exactly what you're doing.
  27. * Some of these settings can damage your printer if improperly set!
  28. *
  29. * Basic settings can be found in Configuration.h
  30. *
  31. */
  32. #ifndef CONFIGURATION_ADV_H
  33. #define CONFIGURATION_ADV_H
  34. /**
  35. *
  36. * ***********************************
  37. * ** ATTENTION TO ALL DEVELOPERS **
  38. * ***********************************
  39. *
  40. * You must increment this version number for every significant change such as,
  41. * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
  42. *
  43. * Note: Update also Version.h !
  44. */
  45. #define CONFIGURATION_ADV_H_VERSION 010100
  46. // @section temperature
  47. //===========================================================================
  48. //=============================Thermal Settings ============================
  49. //===========================================================================
  50. #if DISABLED(PIDTEMPBED)
  51. #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
  52. #if ENABLED(BED_LIMIT_SWITCHING)
  53. #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
  54. #endif
  55. #endif
  56. /**
  57. * Thermal Protection protects your printer from damage and fire if a
  58. * thermistor falls out or temperature sensors fail in any way.
  59. *
  60. * The issue: If a thermistor falls out or a temperature sensor fails,
  61. * Marlin can no longer sense the actual temperature. Since a disconnected
  62. * thermistor reads as a low temperature, the firmware will keep the heater on.
  63. *
  64. * The solution: Once the temperature reaches the target, start observing.
  65. * If the temperature stays too far below the target (hysteresis) for too long (period),
  66. * the firmware will halt the machine as a safety precaution.
  67. *
  68. * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  69. */
  70. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  71. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  72. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  73. /**
  74. * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
  75. * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
  76. * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
  77. * but only if the current temperature is far enough below the target for a reliable test.
  78. *
  79. * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
  80. * WATCH_TEMP_INCREASE should not be below 2.
  81. */
  82. #define WATCH_TEMP_PERIOD 20 // Seconds
  83. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  84. #endif
  85. /**
  86. * Thermal Protection parameters for the bed are just as above for hotends.
  87. */
  88. #if ENABLED(THERMAL_PROTECTION_BED)
  89. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  90. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  91. /**
  92. * Whenever an M140 or M190 increases the target temperature the firmware will wait for the
  93. * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
  94. * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
  95. * but only if the current temperature is far enough below the target for a reliable test.
  96. *
  97. * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
  98. * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
  99. */
  100. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  101. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  102. #endif
  103. #if ENABLED(PIDTEMP)
  104. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  105. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
  106. //#define PID_EXTRUSION_SCALING
  107. #if ENABLED(PID_EXTRUSION_SCALING)
  108. #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
  109. #define LPQ_MAX_LEN 50
  110. #endif
  111. #endif
  112. /**
  113. * Automatic Temperature:
  114. * The hotend target temperature is calculated by all the buffered lines of gcode.
  115. * The maximum buffered steps/sec of the extruder motor is called "se".
  116. * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
  117. * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
  118. * mintemp and maxtemp. Turn this off by executing M109 without F*
  119. * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
  120. * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
  121. */
  122. #define AUTOTEMP
  123. #if ENABLED(AUTOTEMP)
  124. #define AUTOTEMP_OLDWEIGHT 0.98
  125. #endif
  126. //Show Temperature ADC value
  127. //The M105 command return, besides traditional information, the ADC value read from temperature sensors.
  128. //#define SHOW_TEMP_ADC_VALUES
  129. /**
  130. * High Temperature Thermistor Support
  131. *
  132. * Thermistors able to support high temperature tend to have a hard time getting
  133. * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
  134. * will probably be caught when the heating element first turns on during the
  135. * preheating process, which will trigger a min_temp_error as a safety measure
  136. * and force stop everything.
  137. * To circumvent this limitation, we allow for a preheat time (during which,
  138. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  139. * aberrant readings.
  140. *
  141. * If you want to enable this feature for your hotend thermistor(s)
  142. * uncomment and set values > 0 in the constants below
  143. */
  144. // The number of consecutive low temperature errors that can occur
  145. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  146. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  147. // The number of milliseconds a hotend will preheat before starting to check
  148. // the temperature. This value should NOT be set to the time it takes the
  149. // hot end to reach the target temperature, but the time it takes to reach
  150. // the minimum temperature your thermistor can read. The lower the better/safer.
  151. // This shouldn't need to be more than 30 seconds (30000)
  152. //#define MILLISECONDS_PREHEAT_TIME 0
  153. // @section extruder
  154. // Extruder runout prevention.
  155. // If the machine is idle and the temperature over MINTEMP
  156. // then extrude some filament every couple of SECONDS.
  157. //#define EXTRUDER_RUNOUT_PREVENT
  158. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  159. #define EXTRUDER_RUNOUT_MINTEMP 190
  160. #define EXTRUDER_RUNOUT_SECONDS 30
  161. #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
  162. #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
  163. #endif
  164. // @section temperature
  165. //These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
  166. //The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
  167. #define TEMP_SENSOR_AD595_OFFSET 0.0
  168. #define TEMP_SENSOR_AD595_GAIN 1.0
  169. //This is for controlling a fan to cool down the stepper drivers
  170. //it will turn on when any driver is enabled
  171. //and turn off after the set amount of seconds from last driver being disabled again
  172. #define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable)
  173. #define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
  174. #define CONTROLLERFAN_SPEED 255 // == full speed
  175. // When first starting the main fan, run it at full speed for the
  176. // given number of milliseconds. This gets the fan spinning reliably
  177. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  178. //#define FAN_KICKSTART_TIME 100
  179. // This defines the minimal speed for the main fan, run in PWM mode
  180. // to enable uncomment and set minimal PWM speed for reliable running (1-255)
  181. // if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
  182. //#define FAN_MIN_PWM 50
  183. // @section extruder
  184. /**
  185. * Extruder cooling fans
  186. *
  187. * Extruder auto fans automatically turn on when their extruders'
  188. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  189. *
  190. * Your board's pins file specifies the recommended pins. Override those here
  191. * or set to -1 to disable completely.
  192. *
  193. * Multiple extruders can be assigned to the same pin in which case
  194. * the fan will turn on when any selected extruder is above the threshold.
  195. */
  196. #define E0_AUTO_FAN_PIN -1
  197. #define E1_AUTO_FAN_PIN -1
  198. #define E2_AUTO_FAN_PIN -1
  199. #define E3_AUTO_FAN_PIN -1
  200. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  201. #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
  202. // Define a pin to turn case light on/off
  203. //#define CASE_LIGHT_PIN 4
  204. #if PIN_EXISTS(CASE_LIGHT)
  205. #define INVERT_CASE_LIGHT false // Set to true if HIGH is the OFF state (active low)
  206. //#define CASE_LIGHT_DEFAULT_ON // Uncomment to set default state to on
  207. //#define MENU_ITEM_CASE_LIGHT // Uncomment to have a Case Light On / Off entry in main menu
  208. #endif
  209. //===========================================================================
  210. //============================ Mechanical Settings ==========================
  211. //===========================================================================
  212. // @section homing
  213. // If you want endstops to stay on (by default) even when not homing
  214. // enable this option. Override at any time with M120, M121.
  215. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  216. // @section extras
  217. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  218. // Dual X Steppers
  219. // Uncomment this option to drive two X axis motors.
  220. // The next unused E driver will be assigned to the second X stepper.
  221. //#define X_DUAL_STEPPER_DRIVERS
  222. #if ENABLED(X_DUAL_STEPPER_DRIVERS)
  223. // Set true if the two X motors need to rotate in opposite directions
  224. #define INVERT_X2_VS_X_DIR true
  225. #endif
  226. // Dual Y Steppers
  227. // Uncomment this option to drive two Y axis motors.
  228. // The next unused E driver will be assigned to the second Y stepper.
  229. //#define Y_DUAL_STEPPER_DRIVERS
  230. #if ENABLED(Y_DUAL_STEPPER_DRIVERS)
  231. // Set true if the two Y motors need to rotate in opposite directions
  232. #define INVERT_Y2_VS_Y_DIR true
  233. #endif
  234. // A single Z stepper driver is usually used to drive 2 stepper motors.
  235. // Uncomment this option to use a separate stepper driver for each Z axis motor.
  236. // The next unused E driver will be assigned to the second Z stepper.
  237. //#define Z_DUAL_STEPPER_DRIVERS
  238. #if ENABLED(Z_DUAL_STEPPER_DRIVERS)
  239. // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
  240. // That way the machine is capable to align the bed during home, since both Z steppers are homed.
  241. // There is also an implementation of M666 (software endstops adjustment) to this feature.
  242. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
  243. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
  244. // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
  245. // Play a little bit with small adjustments (0.5mm) and check the behaviour.
  246. // The M119 (endstops report) will start reporting the Z2 Endstop as well.
  247. //#define Z_DUAL_ENDSTOPS
  248. #if ENABLED(Z_DUAL_ENDSTOPS)
  249. #define Z2_USE_ENDSTOP _XMAX_
  250. #endif
  251. #endif // Z_DUAL_STEPPER_DRIVERS
  252. // Enable this for dual x-carriage printers.
  253. // A dual x-carriage design has the advantage that the inactive extruder can be parked which
  254. // prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
  255. // allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
  256. //#define DUAL_X_CARRIAGE
  257. #if ENABLED(DUAL_X_CARRIAGE)
  258. // Configuration for second X-carriage
  259. // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
  260. // the second x-carriage always homes to the maximum endstop.
  261. #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
  262. #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
  263. #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
  264. #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
  265. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
  266. // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
  267. // without modifying the firmware (through the "M218 T1 X???" command).
  268. // Remember: you should set the second extruder x-offset to 0 in your slicer.
  269. // There are a few selectable movement modes for dual x-carriages using M605 S<mode>
  270. // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
  271. // as long as it supports dual x-carriages. (M605 S0)
  272. // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
  273. // that additional slicer support is not required. (M605 S1)
  274. // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
  275. // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
  276. // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
  277. // This is the default power-up mode which can be later using M605.
  278. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
  279. // Default settings in "Auto-park Mode"
  280. #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
  281. #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
  282. // Default x offset in duplication mode (typically set to half print bed width)
  283. #define DEFAULT_DUPLICATION_X_OFFSET 100
  284. #endif //DUAL_X_CARRIAGE
  285. // @section homing
  286. //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
  287. #define X_HOME_BUMP_MM 5
  288. #define Y_HOME_BUMP_MM 5
  289. #define Z_HOME_BUMP_MM 2
  290. #define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  291. //#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
  292. // When G28 is called, this option will make Y home before X
  293. //#define HOME_Y_BEFORE_X
  294. // @section machine
  295. #define AXIS_RELATIVE_MODES {false, false, false, false}
  296. // Allow duplication mode with a basic dual-nozzle extruder
  297. //#define DUAL_NOZZLE_DUPLICATION_MODE
  298. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  299. #define INVERT_X_STEP_PIN false
  300. #define INVERT_Y_STEP_PIN false
  301. #define INVERT_Z_STEP_PIN false
  302. #define INVERT_E_STEP_PIN false
  303. // Default stepper release if idle. Set to 0 to deactivate.
  304. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
  305. // Time can be set by M18 and M84.
  306. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  307. #define DISABLE_INACTIVE_X true
  308. #define DISABLE_INACTIVE_Y true
  309. #define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
  310. #define DISABLE_INACTIVE_E true
  311. #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
  312. #define DEFAULT_MINTRAVELFEEDRATE 0.0
  313. // @section lcd
  314. #if ENABLED(ULTIPANEL)
  315. #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
  316. #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
  317. #endif
  318. // @section extras
  319. // minimum time in microseconds that a movement needs to take if the buffer is emptied.
  320. #define DEFAULT_MINSEGMENTTIME 20000
  321. // If defined the movements slow down when the look ahead buffer is only half full
  322. #define SLOWDOWN
  323. // Frequency limit
  324. // See nophead's blog for more info
  325. // Not working O
  326. //#define XY_FREQUENCY_LIMIT 15
  327. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  328. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  329. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  330. #define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
  331. // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
  332. #define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
  333. // Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
  334. #define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  335. // Motor Current controlled via PWM (Overridable on supported boards with PWM-driven motor driver current)
  336. //#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
  337. // uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
  338. //#define DIGIPOT_I2C
  339. // Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
  340. #define DIGIPOT_I2C_NUM_CHANNELS 8
  341. // actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
  342. #define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
  343. //===========================================================================
  344. //=============================Additional Features===========================
  345. //===========================================================================
  346. #define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
  347. #define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
  348. #define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
  349. //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  350. #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
  351. // @section lcd
  352. // Include a page of printer information in the LCD Main Menu
  353. //#define LCD_INFO_MENU
  354. // On the Info Screen, display XY with one decimal place when possible
  355. //#define LCD_DECIMAL_SMALL_XY
  356. #if ENABLED(SDSUPPORT)
  357. // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
  358. // around this by connecting a push button or single throw switch to the pin defined
  359. // as SD_DETECT_PIN in your board's pins definitions.
  360. // This setting should be disabled unless you are using a push button, pulling the pin to ground.
  361. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
  362. #define SD_DETECT_INVERTED
  363. #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
  364. #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
  365. #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
  366. // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
  367. // using:
  368. //#define MENU_ADDAUTOSTART
  369. // Show a progress bar on HD44780 LCDs for SD printing
  370. //#define LCD_PROGRESS_BAR
  371. #if ENABLED(LCD_PROGRESS_BAR)
  372. // Amount of time (ms) to show the bar
  373. #define PROGRESS_BAR_BAR_TIME 2000
  374. // Amount of time (ms) to show the status message
  375. #define PROGRESS_BAR_MSG_TIME 3000
  376. // Amount of time (ms) to retain the status message (0=forever)
  377. #define PROGRESS_MSG_EXPIRE 0
  378. // Enable this to show messages for MSG_TIME then hide them
  379. //#define PROGRESS_MSG_ONCE
  380. // Add a menu item to test the progress bar:
  381. //#define LCD_PROGRESS_BAR_TEST
  382. #endif
  383. // This allows hosts to request long names for files and folders with M33
  384. //#define LONG_FILENAME_HOST_SUPPORT
  385. // This option allows you to abort SD printing when any endstop is triggered.
  386. // This feature must be enabled with "M540 S1" or from the LCD menu.
  387. // To have any effect, endstops must be enabled during SD printing.
  388. //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
  389. #endif // SDSUPPORT
  390. /**
  391. * Additional options for Graphical Displays
  392. *
  393. * Use the optimizations here to improve printing performance,
  394. * which can be adversely affected by graphical display drawing,
  395. * especially when doing several short moves, and when printing
  396. * on DELTA and SCARA machines.
  397. *
  398. * Some of these options may result in the display lagging behind
  399. * controller events, as there is a trade-off between reliable
  400. * printing performance versus fast display updates.
  401. */
  402. #if ENABLED(DOGLCD)
  403. // Enable to save many cycles by drawing a hollow frame on the Info Screen
  404. #define XYZ_HOLLOW_FRAME
  405. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  406. #define MENU_HOLLOW_FRAME
  407. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
  408. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  409. //#define USE_BIG_EDIT_FONT
  410. // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
  411. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  412. //#define USE_SMALL_INFOFONT
  413. // Enable this option and reduce the value to optimize screen updates.
  414. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  415. //#define DOGM_SPI_DELAY_US 5
  416. #endif // DOGLCD
  417. // @section safety
  418. // The hardware watchdog should reset the microcontroller disabling all outputs,
  419. // in case the firmware gets stuck and doesn't do temperature regulation.
  420. #define USE_WATCHDOG
  421. #if ENABLED(USE_WATCHDOG)
  422. // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
  423. // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
  424. // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
  425. //#define WATCHDOG_RESET_MANUAL
  426. #endif
  427. // @section lcd
  428. // Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
  429. // it can e.g. be used to change z-positions in the print startup phase in real-time
  430. // does not respect endstops!
  431. //#define BABYSTEPPING
  432. #if ENABLED(BABYSTEPPING)
  433. #define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
  434. //not implemented for deltabots!
  435. #define BABYSTEP_INVERT_Z false //true for inverse movements in Z
  436. #define BABYSTEP_MULTIPLICATOR 1 //faster movements
  437. #endif
  438. // @section extruder
  439. // extruder advance constant (s2/mm3)
  440. //
  441. // advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
  442. //
  443. // Hooke's law says: force = k * distance
  444. // Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
  445. // so: v ^ 2 is proportional to number of steps we advance the extruder
  446. //#define ADVANCE
  447. #if ENABLED(ADVANCE)
  448. #define EXTRUDER_ADVANCE_K .0
  449. #define D_FILAMENT 2.85
  450. #endif
  451. /**
  452. * Implementation of linear pressure control
  453. *
  454. * Assumption: advance = k * (delta velocity)
  455. * K=0 means advance disabled.
  456. * See Marlin documentation for calibration instructions.
  457. */
  458. //#define LIN_ADVANCE
  459. #if ENABLED(LIN_ADVANCE)
  460. #define LIN_ADVANCE_K 75
  461. #endif
  462. // @section leveling
  463. // Default mesh area is an area with an inset margin on the print area.
  464. // Below are the macros that are used to define the borders for the mesh area,
  465. // made available here for specialized needs, ie dual extruder setup.
  466. #if ENABLED(MESH_BED_LEVELING)
  467. #define MESH_MIN_X (X_MIN_POS + MESH_INSET)
  468. #define MESH_MAX_X (X_MAX_POS - (MESH_INSET))
  469. #define MESH_MIN_Y (Y_MIN_POS + MESH_INSET)
  470. #define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET))
  471. #endif
  472. // @section extras
  473. // Arc interpretation settings:
  474. #define ARC_SUPPORT // Disabling this saves ~2738 bytes
  475. #define MM_PER_ARC_SEGMENT 1
  476. #define N_ARC_CORRECTION 25
  477. // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
  478. //#define BEZIER_CURVE_SUPPORT
  479. // G38.2 and G38.3 Probe Target
  480. //#define G38_PROBE_TARGET
  481. #if ENABLED(G38_PROBE_TARGET)
  482. #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
  483. #endif
  484. // Moves (or segments) with fewer steps than this will be joined with the next move
  485. #define MIN_STEPS_PER_SEGMENT 6
  486. // The minimum pulse width (in µs) for stepping a stepper.
  487. // Set this if you find stepping unreliable, or if using a very fast CPU.
  488. #define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed
  489. // @section temperature
  490. // Control heater 0 and heater 1 in parallel.
  491. //#define HEATERS_PARALLEL
  492. //===========================================================================
  493. //================================= Buffers =================================
  494. //===========================================================================
  495. // @section hidden
  496. // The number of linear motions that can be in the plan at any give time.
  497. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
  498. #if ENABLED(SDSUPPORT)
  499. #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
  500. #else
  501. #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
  502. #endif
  503. // @section serial
  504. // The ASCII buffer for serial input
  505. #define MAX_CMD_SIZE 96
  506. #define BUFSIZE 4
  507. // Transfer Buffer Size
  508. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  509. // To buffer a simple "ok" you need 4 bytes.
  510. // For ADVANCED_OK (M105) you need 32 bytes.
  511. // For debug-echo: 128 bytes for the optimal speed.
  512. // Other output doesn't need to be that speedy.
  513. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  514. #define TX_BUFFER_SIZE 0
  515. // Enable an emergency-command parser to intercept certain commands as they
  516. // enter the serial receive buffer, so they cannot be blocked.
  517. // Currently handles M108, M112, M410
  518. // Does not work on boards using AT90USB (USBCON) processors!
  519. //#define EMERGENCY_PARSER
  520. // Bad Serial-connections can miss a received command by sending an 'ok'
  521. // Therefore some clients abort after 30 seconds in a timeout.
  522. // Some other clients start sending commands while receiving a 'wait'.
  523. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  524. //#define NO_TIMEOUTS 1000 // Milliseconds
  525. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  526. //#define ADVANCED_OK
  527. // @section fwretract
  528. // Firmware based and LCD controlled retract
  529. // M207 and M208 can be used to define parameters for the retraction.
  530. // The retraction can be called by the slicer using G10 and G11
  531. // until then, intended retractions can be detected by moves that only extrude and the direction.
  532. // the moves are than replaced by the firmware controlled ones.
  533. //#define FWRETRACT //ONLY PARTIALLY TESTED
  534. #if ENABLED(FWRETRACT)
  535. #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
  536. #define RETRACT_LENGTH 3 //default retract length (positive mm)
  537. #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
  538. #define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
  539. #define RETRACT_ZLIFT 0 //default retract Z-lift
  540. #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
  541. #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
  542. #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
  543. #endif
  544. /**
  545. * Filament Change
  546. * Experimental filament change support.
  547. * Adds the GCode M600 for initiating filament change.
  548. *
  549. * Requires an LCD display.
  550. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  551. */
  552. //#define FILAMENT_CHANGE_FEATURE
  553. #if ENABLED(FILAMENT_CHANGE_FEATURE)
  554. #define FILAMENT_CHANGE_X_POS 3 // X position of hotend
  555. #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
  556. #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
  557. #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
  558. #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
  559. #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
  560. // It is a short retract used immediately after print interrupt before move to filament exchange position
  561. #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
  562. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
  563. // Longer length for bowden printers to unload filament from whole bowden tube,
  564. // shorter lenght for printers without bowden to unload filament from extruder only,
  565. // 0 to disable unloading for manual unloading
  566. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
  567. #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
  568. // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
  569. // Short or zero length for printers without bowden where loading is not used
  570. #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
  571. #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
  572. // 0 to disable for manual extrusion
  573. // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
  574. // or until outcoming filament color is not clear for filament color change
  575. #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
  576. #endif
  577. /******************************************************************************\
  578. * enable this section if you have TMC26X motor drivers.
  579. * you need to import the TMC26XStepper library into the Arduino IDE for this
  580. ******************************************************************************/
  581. // @section tmc
  582. //#define HAVE_TMCDRIVER
  583. #if ENABLED(HAVE_TMCDRIVER)
  584. //#define X_IS_TMC
  585. //#define X2_IS_TMC
  586. //#define Y_IS_TMC
  587. //#define Y2_IS_TMC
  588. //#define Z_IS_TMC
  589. //#define Z2_IS_TMC
  590. //#define E0_IS_TMC
  591. //#define E1_IS_TMC
  592. //#define E2_IS_TMC
  593. //#define E3_IS_TMC
  594. #define X_MAX_CURRENT 1000 // in mA
  595. #define X_SENSE_RESISTOR 91 // in mOhms
  596. #define X_MICROSTEPS 16 // number of microsteps
  597. #define X2_MAX_CURRENT 1000
  598. #define X2_SENSE_RESISTOR 91
  599. #define X2_MICROSTEPS 16
  600. #define Y_MAX_CURRENT 1000
  601. #define Y_SENSE_RESISTOR 91
  602. #define Y_MICROSTEPS 16
  603. #define Y2_MAX_CURRENT 1000
  604. #define Y2_SENSE_RESISTOR 91
  605. #define Y2_MICROSTEPS 16
  606. #define Z_MAX_CURRENT 1000
  607. #define Z_SENSE_RESISTOR 91
  608. #define Z_MICROSTEPS 16
  609. #define Z2_MAX_CURRENT 1000
  610. #define Z2_SENSE_RESISTOR 91
  611. #define Z2_MICROSTEPS 16
  612. #define E0_MAX_CURRENT 1000
  613. #define E0_SENSE_RESISTOR 91
  614. #define E0_MICROSTEPS 16
  615. #define E1_MAX_CURRENT 1000
  616. #define E1_SENSE_RESISTOR 91
  617. #define E1_MICROSTEPS 16
  618. #define E2_MAX_CURRENT 1000
  619. #define E2_SENSE_RESISTOR 91
  620. #define E2_MICROSTEPS 16
  621. #define E3_MAX_CURRENT 1000
  622. #define E3_SENSE_RESISTOR 91
  623. #define E3_MICROSTEPS 16
  624. #endif
  625. // @section TMC2130
  626. /**
  627. * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
  628. *
  629. * To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
  630. * (https://github.com/makertum/Trinamic_TMC2130).
  631. *
  632. * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
  633. * the hardware SPI interface on your board and define the required CS pins
  634. * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  635. */
  636. //#define HAVE_TMC2130DRIVER
  637. #if ENABLED(HAVE_TMC2130DRIVER)
  638. //#define TMC2130_ADVANCED_CONFIGURATION
  639. // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
  640. //#define X_IS_TMC2130
  641. //#define X2_IS_TMC2130
  642. //#define Y_IS_TMC2130
  643. //#define Y2_IS_TMC2130
  644. //#define Z_IS_TMC2130
  645. //#define Z2_IS_TMC2130
  646. //#define E0_IS_TMC2130
  647. //#define E1_IS_TMC2130
  648. //#define E2_IS_TMC2130
  649. //#define E3_IS_TMC2130
  650. #if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
  651. // If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
  652. // Enabled settings will be automatically applied to all axes specified above.
  653. //
  654. // Please read the TMC2130 datasheet:
  655. // http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
  656. // All settings here have the same (sometimes cryptic) names as in the datasheet.
  657. //
  658. // The following, uncommented settings are only suggestion.
  659. /* GENERAL CONFIGURATION */
  660. //#define GLOBAL_EN_PWM_MODE 0
  661. #define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
  662. //#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
  663. #define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
  664. //#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
  665. #define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
  666. //#define GLOBAL_DIAG0_ERROR 0 // [0,1]
  667. //#define GLOBAL_DIAG0_OTPW 0 // [0,1]
  668. //#define GLOBAL_DIAG0_STALL 0 // [0,1]
  669. //#define GLOBAL_DIAG1_STALL 0 // [0,1]
  670. //#define GLOBAL_DIAG1_INDEX 0 // [0,1]
  671. //#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
  672. //#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
  673. //#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
  674. //#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
  675. //#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
  676. //#define GLOBAL_STOP_ENABLE 0 // [0,1]
  677. //#define GLOBAL_DIRECT_MODE 0 // [0,1]
  678. /* VELOCITY-DEPENDENT DRIVE FEATURES */
  679. #define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
  680. #define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
  681. #define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
  682. //#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
  683. //#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
  684. //#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
  685. #define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
  686. /* SPI MODE CONFIGURATION */
  687. //#define GLOBAL_XDIRECT 0
  688. /* DCSTEP MINIMUM VELOCITY */
  689. //#define GLOBAL_VDCMIN 0
  690. /* MOTOR DRIVER CONFIGURATION*/
  691. //#define GLOBAL_DEDGE 0
  692. //#define GLOBAL_DISS2G 0
  693. #define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
  694. #define GLOBAL_MRES 16 // number of microsteps
  695. #define GLOBAL_SYNC 1 // [0-15]
  696. #define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
  697. #define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
  698. // #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
  699. #define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
  700. #define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
  701. //#define GLOBAL_RNDTF 0
  702. //#define GLOBAL_DISFDCC 0
  703. //#define GLOBAL_FD 0
  704. //#define GLOBAL_HEND 0
  705. //#define GLOBAL_HSTRT 0
  706. #define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
  707. //#define GLOBAL_SFILT 0
  708. //#define GLOBAL_SGT 0
  709. //#define GLOBAL_SEIMIN 0
  710. //#define GLOBAL_SEDN 0
  711. //#define GLOBAL_SEMAX 0
  712. //#define GLOBAL_SEUP 0
  713. //#define GLOBAL_SEMIN 0
  714. //#define GLOBAL_DC_TIME 0
  715. //#define GLOBAL_DC_SG 0
  716. //#define GLOBAL_FREEWHEEL 0
  717. //#define GLOBAL_PWM_SYMMETRIC 0
  718. //#define GLOBAL_PWM_AUTOSCALE 0
  719. //#define GLOBAL_PWM_FREQ 0
  720. //#define GLOBAL_PWM_GRAD 0
  721. //#define GLOBAL_PWM_AMPL 0
  722. //#define GLOBAL_ENCM_CTRL 0
  723. #else
  724. #define X_IHOLD 31 // [0-31] 0: min, 31: max
  725. #define X_IRUN 31 // [0-31] 0: min, 31: max
  726. #define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
  727. #define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
  728. #define X_MRES 16 // number of microsteps
  729. #define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
  730. #define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
  731. #define X2_IHOLD 31
  732. #define X2_IRUN 31
  733. #define X2_IHOLDDELAY 15
  734. #define X2_I_SCALE_ANALOG 1
  735. #define X2_MRES 16
  736. #define X2_TBL 1
  737. #define X2_TOFF 8
  738. #define Y_IHOLD 31
  739. #define Y_IRUN 31
  740. #define Y_IHOLDDELAY 15
  741. #define Y_I_SCALE_ANALOG 1
  742. #define Y_MRES 16
  743. #define Y_TBL 1
  744. #define Y_TOFF 8
  745. #define Y2_IHOLD 31
  746. #define Y2_IRUN 31
  747. #define Y2_IHOLDDELAY 15
  748. #define Y2_I_SCALE_ANALOG 1
  749. #define Y2_MRES 16
  750. #define Y2_TBL 1
  751. #define Y2_TOFF 8
  752. #define Z_IHOLD 31
  753. #define Z_IRUN 31
  754. #define Z_IHOLDDELAY 15
  755. #define Z_I_SCALE_ANALOG 1
  756. #define Z_MRES 16
  757. #define Z_TBL 1
  758. #define Z_TOFF 8
  759. #define Z2_IHOLD 31
  760. #define Z2_IRUN 31
  761. #define Z2_IHOLDDELAY 15
  762. #define Z2_I_SCALE_ANALOG 1
  763. #define Z2_MRES 16
  764. #define Z2_TBL 1
  765. #define Z2_TOFF 8
  766. #define E0_IHOLD 31
  767. #define E0_IRUN 31
  768. #define E0_IHOLDDELAY 15
  769. #define E0_I_SCALE_ANALOG 1
  770. #define E0_MRES 16
  771. #define E0_TBL 1
  772. #define E0_TOFF 8
  773. #define E1_IHOLD 31
  774. #define E1_IRUN 31
  775. #define E1_IHOLDDELAY 15
  776. #define E1_I_SCALE_ANALOG 1
  777. #define E1_MRES 16
  778. #define E1_TBL 1
  779. #define E1_TOFF 8
  780. #define E2_IHOLD 31
  781. #define E2_IRUN 31
  782. #define E2_IHOLDDELAY 15
  783. #define E2_I_SCALE_ANALOG 1
  784. #define E2_MRES 16
  785. #define E2_TBL 1
  786. #define E2_TOFF 8
  787. #define E3_IHOLD 31
  788. #define E3_IRUN 31
  789. #define E3_IHOLDDELAY 15
  790. #define E3_I_SCALE_ANALOG 1
  791. #define E3_MRES 16
  792. #define E3_TBL 1
  793. #define E3_TOFF 8
  794. #endif // TMC2130_ADVANCED_CONFIGURATION
  795. #endif // HAVE_TMC2130DRIVER
  796. // @section L6470
  797. /**
  798. * Enable this section if you have L6470 motor drivers.
  799. * You need to import the L6470 library into the Arduino IDE for this.
  800. * (https://github.com/ameyer/Arduino-L6470)
  801. */
  802. //#define HAVE_L6470DRIVER
  803. #if ENABLED(HAVE_L6470DRIVER)
  804. //#define X_IS_L6470
  805. //#define X2_IS_L6470
  806. //#define Y_IS_L6470
  807. //#define Y2_IS_L6470
  808. //#define Z_IS_L6470
  809. //#define Z2_IS_L6470
  810. //#define E0_IS_L6470
  811. //#define E1_IS_L6470
  812. //#define E2_IS_L6470
  813. //#define E3_IS_L6470
  814. #define X_MICROSTEPS 16 // number of microsteps
  815. #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
  816. #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
  817. #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
  818. #define X2_MICROSTEPS 16
  819. #define X2_K_VAL 50
  820. #define X2_OVERCURRENT 2000
  821. #define X2_STALLCURRENT 1500
  822. #define Y_MICROSTEPS 16
  823. #define Y_K_VAL 50
  824. #define Y_OVERCURRENT 2000
  825. #define Y_STALLCURRENT 1500
  826. #define Y2_MICROSTEPS 16
  827. #define Y2_K_VAL 50
  828. #define Y2_OVERCURRENT 2000
  829. #define Y2_STALLCURRENT 1500
  830. #define Z_MICROSTEPS 16
  831. #define Z_K_VAL 50
  832. #define Z_OVERCURRENT 2000
  833. #define Z_STALLCURRENT 1500
  834. #define Z2_MICROSTEPS 16
  835. #define Z2_K_VAL 50
  836. #define Z2_OVERCURRENT 2000
  837. #define Z2_STALLCURRENT 1500
  838. #define E0_MICROSTEPS 16
  839. #define E0_K_VAL 50
  840. #define E0_OVERCURRENT 2000
  841. #define E0_STALLCURRENT 1500
  842. #define E1_MICROSTEPS 16
  843. #define E1_K_VAL 50
  844. #define E1_OVERCURRENT 2000
  845. #define E1_STALLCURRENT 1500
  846. #define E2_MICROSTEPS 16
  847. #define E2_K_VAL 50
  848. #define E2_OVERCURRENT 2000
  849. #define E2_STALLCURRENT 1500
  850. #define E3_MICROSTEPS 16
  851. #define E3_K_VAL 50
  852. #define E3_OVERCURRENT 2000
  853. #define E3_STALLCURRENT 1500
  854. #endif
  855. /**
  856. * TWI/I2C BUS
  857. *
  858. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  859. * machines. Enabling this will allow you to send and receive I2C data from slave
  860. * devices on the bus.
  861. *
  862. * ; Example #1
  863. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  864. * ; It uses multiple M260 commands with one B<base 10> arg
  865. * M260 A99 ; Target slave address
  866. * M260 B77 ; M
  867. * M260 B97 ; a
  868. * M260 B114 ; r
  869. * M260 B108 ; l
  870. * M260 B105 ; i
  871. * M260 B110 ; n
  872. * M260 S1 ; Send the current buffer
  873. *
  874. * ; Example #2
  875. * ; Request 6 bytes from slave device with address 0x63 (99)
  876. * M261 A99 B5
  877. *
  878. * ; Example #3
  879. * ; Example serial output of a M261 request
  880. * echo:i2c-reply: from:99 bytes:5 data:hello
  881. */
  882. // @section i2cbus
  883. //#define EXPERIMENTAL_I2CBUS
  884. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  885. /**
  886. * Add M43 command for pins info and testing
  887. */
  888. //#define PINS_DEBUGGING
  889. /**
  890. * Auto-report temperatures with M155 S<seconds>
  891. */
  892. //#define AUTO_REPORT_TEMPERATURES
  893. /**
  894. * Include capabilities in M115 output
  895. */
  896. //#define EXTENDED_CAPABILITIES_REPORT
  897. /**
  898. * Volumetric extrusion default state
  899. * Activate to make volumetric extrusion the default method,
  900. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  901. *
  902. * M200 D0 to disable, M200 Dn to set a new diameter.
  903. */
  904. //#define VOLUMETRIC_DEFAULT_ON
  905. #endif // CONFIGURATION_ADV_H