My Marlin configs for Fabrikator Mini and CTC i3 Pro B
您最多选择25个主题 主题必须以字母或数字开头,可以包含连字符 (-),并且长度不得超过35个字符

SanityCheck.h 37KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * SanityCheck.h
  24. *
  25. * Test configuration values for errors at compile-time.
  26. */
  27. /**
  28. * Require gcc 4.7 or newer (first included with Arduino 1.6.8) for C++11 features.
  29. */
  30. #if __cplusplus < 201103L
  31. #error "Marlin requires C++11 support (gcc >= 4.7, Arduino IDE >= 1.6.8). Please upgrade your toolchain."
  32. #endif
  33. /**
  34. * We try our best to include sanity checks for all the changes configuration
  35. * directives because people have a tendency to use outdated config files with
  36. * the bleding edge source code, but sometimes this is not enough. This check
  37. * will force a minimum config file revision, otherwise Marlin will not build.
  38. */
  39. #if ! defined(CONFIGURATION_H_VERSION) || CONFIGURATION_H_VERSION < REQUIRED_CONFIGURATION_H_VERSION
  40. #error "You are using an old Configuration.h file, update it before building Marlin."
  41. #endif
  42. #if ! defined(CONFIGURATION_ADV_H_VERSION) || CONFIGURATION_ADV_H_VERSION < REQUIRED_CONFIGURATION_ADV_H_VERSION
  43. #error "You are using an old Configuration_adv.h file, update it before building Marlin."
  44. #endif
  45. /**
  46. * Warnings for old configurations
  47. */
  48. #if WATCH_TEMP_PERIOD > 500
  49. #error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds."
  50. #elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD))
  51. #error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS."
  52. #elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD)
  53. #error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED."
  54. #elif (CORE_IS_XZ || CORE_IS_YZ) && ENABLED(Z_LATE_ENABLE)
  55. #error "Z_LATE_ENABLE can't be used with COREXZ, COREZX, COREYZ, or COREZY."
  56. #elif defined(X_HOME_RETRACT_MM)
  57. #error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
  58. #elif defined(SDCARDDETECTINVERTED)
  59. #error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration."
  60. #elif defined(BTENABLED)
  61. #error "BTENABLED is now BLUETOOTH. Please update your configuration."
  62. #elif defined(CUSTOM_MENDEL_NAME)
  63. #error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration."
  64. #elif defined(HAS_AUTOMATIC_VERSIONING)
  65. #error "HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration."
  66. #elif defined(SDSLOW)
  67. #error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead."
  68. #elif defined(SDEXTRASLOW)
  69. #error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead."
  70. #elif defined(FILAMENT_SENSOR)
  71. #error "FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead."
  72. #elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
  73. #error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead."
  74. #elif ENABLED(Z_DUAL_ENDSTOPS) && !defined(Z2_USE_ENDSTOP)
  75. #error "Z_DUAL_ENDSTOPS settings are simplified. Just set Z2_USE_ENDSTOP to the endstop you want to repurpose for Z2"
  76. #elif defined(LANGUAGE_INCLUDE)
  77. #error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration."
  78. #elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y)
  79. #error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead."
  80. #elif defined(PID_PARAMS_PER_EXTRUDER)
  81. #error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead."
  82. #elif defined(EXTRUDER_WATTS) || defined(BED_WATTS)
  83. #error "EXTRUDER_WATTS and BED_WATTS are deprecated. Remove them from your configuration."
  84. #elif defined(SERVO_ENDSTOP_ANGLES)
  85. #error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead."
  86. #elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR)
  87. #error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed."
  88. #elif defined(DEFAULT_XYJERK)
  89. #error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead."
  90. #elif defined(XY_TRAVEL_SPEED)
  91. #error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
  92. #elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
  93. #error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead."
  94. #elif defined(SERVO_DEACTIVATION_DELAY)
  95. #error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
  96. #elif ENABLED(FILAMENTCHANGEENABLE)
  97. #error "FILAMENTCHANGEENABLE is now FILAMENT_CHANGE_FEATURE. Please update your configuration."
  98. #elif defined(PLA_PREHEAT_HOTEND_TEMP)
  99. #error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
  100. #elif defined(PLA_PREHEAT_HPB_TEMP)
  101. #error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
  102. #elif defined(PLA_PREHEAT_FAN_SPEED)
  103. #error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
  104. #elif defined(ABS_PREHEAT_HOTEND_TEMP)
  105. #error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
  106. #elif defined(ABS_PREHEAT_HPB_TEMP)
  107. #error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
  108. #elif defined(ABS_PREHEAT_FAN_SPEED)
  109. #error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
  110. #elif defined(ENDSTOPS_ONLY_FOR_HOMING)
  111. #error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead."
  112. #elif defined(HOMING_FEEDRATE)
  113. #error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead."
  114. #elif defined(MANUAL_HOME_POSITIONS)
  115. #error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead."
  116. #elif defined(PID_ADD_EXTRUSION_RATE)
  117. #error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration."
  118. #elif defined(Z_RAISE_BEFORE_HOMING)
  119. #error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
  120. #elif defined(MIN_Z_HEIGHT_FOR_HOMING)
  121. #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
  122. #elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
  123. #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE instead."
  124. #elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
  125. #error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
  126. #elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT)
  127. #error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
  128. #elif !defined(MIN_STEPS_PER_SEGMENT)
  129. #error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
  130. #elif defined(PREVENT_DANGEROUS_EXTRUDE)
  131. #error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration."
  132. #elif defined(SCARA)
  133. #error "SCARA is now MORGAN_SCARA. Please update your configuration."
  134. #elif defined(ENABLE_AUTO_BED_LEVELING)
  135. #error "ENABLE_AUTO_BED_LEVELING is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
  136. #elif defined(AUTO_BED_LEVELING_FEATURE)
  137. #error "AUTO_BED_LEVELING_FEATURE is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
  138. #elif defined(ABL_GRID_POINTS)
  139. #error "ABL_GRID_POINTS is now ABL_GRID_MAX_POINTS_X and ABL_GRID_MAX_POINTS_Y. Please update your configuration."
  140. #elif defined(ABL_GRID_POINTS_X) || defined(ABL_GRID_POINTS_Y)
  141. #error "ABL_GRID_POINTS_[XY] is now ABL_GRID_MAX_POINTS_[XY]. Please update your configuration."
  142. #elif defined(BEEPER)
  143. #error "BEEPER is now BEEPER_PIN. Please update your pins definitions."
  144. #elif defined(SDCARDDETECT)
  145. #error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions."
  146. #elif defined(STAT_LED_RED) || defined(STAT_LED_BLUE)
  147. #error "STAT_LED_RED/STAT_LED_BLUE are now STAT_LED_RED_PIN/STAT_LED_BLUE_PIN. Please update your pins definitions."
  148. #elif defined(LCD_PIN_BL)
  149. #error "LCD_PIN_BL is now LCD_BACKLIGHT_PIN. Please update your pins definitions."
  150. #elif defined(LCD_PIN_RESET)
  151. #error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions."
  152. #elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN)
  153. #error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h."
  154. #endif
  155. /**
  156. * Marlin release, version and default string
  157. */
  158. #ifndef SHORT_BUILD_VERSION
  159. #error "SHORT_BUILD_VERSION must be specified."
  160. #elif !defined(DETAILED_BUILD_VERSION)
  161. #error "BUILD_VERSION must be specified."
  162. #elif !defined(STRING_DISTRIBUTION_DATE)
  163. #error "STRING_DISTRIBUTION_DATE must be specified."
  164. #elif !defined(PROTOCOL_VERSION)
  165. #error "PROTOCOL_VERSION must be specified."
  166. #elif !defined(MACHINE_NAME)
  167. #error "MACHINE_NAME must be specified."
  168. #elif !defined(SOURCE_CODE_URL)
  169. #error "SOURCE_CODE_URL must be specified."
  170. #elif !defined(DEFAULT_MACHINE_UUID)
  171. #error "DEFAULT_MACHINE_UUID must be specified."
  172. #elif !defined(WEBSITE_URL)
  173. #error "WEBSITE_URL must be specified."
  174. #endif
  175. /**
  176. * Dual Stepper Drivers
  177. */
  178. #if ENABLED(X_DUAL_STEPPER_DRIVERS) && ENABLED(DUAL_X_CARRIAGE)
  179. #error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS."
  180. #elif ENABLED(X_DUAL_STEPPER_DRIVERS) && (!HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR)
  181. #error "X_DUAL_STEPPER_DRIVERS requires X2 pins (and an extra E plug)."
  182. #elif ENABLED(Y_DUAL_STEPPER_DRIVERS) && (!HAS_Y2_ENABLE || !HAS_Y2_STEP || !HAS_Y2_DIR)
  183. #error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins (and an extra E plug)."
  184. #elif ENABLED(Z_DUAL_STEPPER_DRIVERS) && (!HAS_Z2_ENABLE || !HAS_Z2_STEP || !HAS_Z2_DIR)
  185. #error "Z_DUAL_STEPPER_DRIVERS requires Z2 pins (and an extra E plug)."
  186. #endif
  187. /**
  188. * Progress Bar
  189. */
  190. #if ENABLED(LCD_PROGRESS_BAR)
  191. #if DISABLED(SDSUPPORT)
  192. #error "LCD_PROGRESS_BAR requires SDSUPPORT."
  193. #elif ENABLED(DOGLCD)
  194. #error "LCD_PROGRESS_BAR does not apply to graphical displays."
  195. #elif ENABLED(FILAMENT_LCD_DISPLAY)
  196. #error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
  197. #endif
  198. #endif
  199. /**
  200. * Delta requirements
  201. */
  202. #if ENABLED(DELTA)
  203. #if DISABLED(USE_XMAX_PLUG) && DISABLED(USE_YMAX_PLUG) && DISABLED(USE_ZMAX_PLUG)
  204. #error "You probably want to use Max Endstops for DELTA!"
  205. #endif
  206. #if ABL_GRID
  207. #if (ABL_GRID_MAX_POINTS_X & 1) == 0 || (ABL_GRID_MAX_POINTS_Y & 1) == 0
  208. #error "DELTA requires ABL_GRID_MAX_POINTS_X and ABL_GRID_MAX_POINTS_Y to be odd numbers."
  209. #elif ABL_GRID_MAX_POINTS_X < 3
  210. #error "DELTA requires ABL_GRID_MAX_POINTS_X and ABL_GRID_MAX_POINTS_Y to be 3 or higher."
  211. #endif
  212. #endif
  213. #endif
  214. /**
  215. * Babystepping
  216. */
  217. #if ENABLED(BABYSTEPPING)
  218. #if DISABLED(ULTRA_LCD)
  219. #error "BABYSTEPPING requires an LCD controller."
  220. #endif
  221. #if ENABLED(SCARA)
  222. #error "BABYSTEPPING is not implemented for SCARA yet."
  223. #endif
  224. #if ENABLED(DELTA) && ENABLED(BABYSTEP_XY)
  225. #error "BABYSTEPPING only implemented for Z axis on deltabots."
  226. #endif
  227. #endif
  228. /**
  229. * Filament Runout needs a pin and either SD Support or Auto print start detection
  230. */
  231. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  232. #if !HAS_FIL_RUNOUT
  233. #error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
  234. #elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
  235. #error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
  236. #endif
  237. #endif
  238. /**
  239. * Filament Change with Extruder Runout Prevention
  240. */
  241. #if ENABLED(FILAMENT_CHANGE_FEATURE) && ENABLED(EXTRUDER_RUNOUT_PREVENT)
  242. #error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
  243. #endif
  244. /**
  245. * Individual axis homing is useless for DELTAS
  246. */
  247. #if ENABLED(INDIVIDUAL_AXIS_HOMING_MENU) && ENABLED(DELTA)
  248. #error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics."
  249. #endif
  250. /**
  251. * Options only for EXTRUDERS > 1
  252. */
  253. #if EXTRUDERS > 1
  254. #if EXTRUDERS > 4
  255. #error "The maximum number of EXTRUDERS in Marlin is 4."
  256. #endif
  257. #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
  258. #error "EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT."
  259. #endif
  260. #if ENABLED(HEATERS_PARALLEL)
  261. #error "EXTRUDERS must be 1 with HEATERS_PARALLEL."
  262. #endif
  263. #elif ENABLED(SINGLENOZZLE)
  264. #error "SINGLENOZZLE requires 2 or more EXTRUDERS."
  265. #endif
  266. /**
  267. * Only one type of extruder allowed
  268. */
  269. #if (ENABLED(SWITCHING_EXTRUDER) && (ENABLED(SINGLENOZZLE) || ENABLED(MIXING_EXTRUDER))) \
  270. || (ENABLED(SINGLENOZZLE) && ENABLED(MIXING_EXTRUDER))
  271. #error "Please define only one type of extruder: SINGLENOZZLE, SWITCHING_EXTRUDER, or MIXING_EXTRUDER."
  272. #endif
  273. /**
  274. * Single Stepper Dual Extruder with switching servo
  275. */
  276. #if ENABLED(SWITCHING_EXTRUDER)
  277. #if ENABLED(DUAL_X_CARRIAGE)
  278. #error "SWITCHING_EXTRUDER and DUAL_X_CARRIAGE are incompatible."
  279. #elif EXTRUDERS != 2
  280. #error "SWITCHING_EXTRUDER requires exactly 2 EXTRUDERS."
  281. #elif NUM_SERVOS < 1
  282. #error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1."
  283. #endif
  284. #endif
  285. /**
  286. * Mixing Extruder requirements
  287. */
  288. #if ENABLED(MIXING_EXTRUDER)
  289. #if EXTRUDERS > 1
  290. #error "MIXING_EXTRUDER currently only supports one extruder."
  291. #endif
  292. #if MIXING_STEPPERS < 2
  293. #error "You must set MIXING_STEPPERS >= 2 for a mixing extruder."
  294. #endif
  295. #if ENABLED(FILAMENT_SENSOR)
  296. #error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway."
  297. #endif
  298. #endif
  299. /**
  300. * Limited number of servos
  301. */
  302. #if NUM_SERVOS > 4
  303. #error "The maximum number of SERVOS in Marlin is 4."
  304. #endif
  305. /**
  306. * Servo deactivation depends on servo endstops
  307. */
  308. #if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_ENDSTOP
  309. #error "Z_ENDSTOP_SERVO_NR is required for DEACTIVATE_SERVOS_AFTER_MOVE."
  310. #endif
  311. /**
  312. * Required LCD language
  313. */
  314. #if DISABLED(DOGLCD) && ENABLED(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780)
  315. #error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller."
  316. #endif
  317. /**
  318. * Bed Heating Options - PID vs Limit Switching
  319. */
  320. #if ENABLED(PIDTEMPBED) && ENABLED(BED_LIMIT_SWITCHING)
  321. #error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED."
  322. #endif
  323. /**
  324. * Allow only one bed leveling option to be defined
  325. */
  326. #if HAS_ABL
  327. #define COUNT_LEV_1 0
  328. #if ENABLED(AUTO_BED_LEVELING_LINEAR)
  329. #define COUNT_LEV_2 INCREMENT(COUNT_LEV_1)
  330. #else
  331. #define COUNT_LEV_2 COUNT_LEV_1
  332. #endif
  333. #if ENABLED(AUTO_BED_LEVELING_3POINT)
  334. #define COUNT_LEV_3 INCREMENT(COUNT_LEV_2)
  335. #else
  336. #define COUNT_LEV_3 COUNT_LEV_2
  337. #endif
  338. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  339. #define COUNT_LEV_4 INCREMENT(COUNT_LEV_3)
  340. #else
  341. #define COUNT_LEV_4 COUNT_LEV_3
  342. #endif
  343. #if ENABLED(MESH_BED_LEVELING)
  344. #define COUNT_LEV_5 INCREMENT(COUNT_LEV_4)
  345. #else
  346. #define COUNT_LEV_5 COUNT_LEV_4
  347. #endif
  348. #if COUNT_LEV_5 > 1
  349. #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, or AUTO_BED_LEVELING_BILINEAR."
  350. #endif
  351. #endif
  352. /**
  353. * Mesh Bed Leveling
  354. */
  355. #if ENABLED(MESH_BED_LEVELING)
  356. #if ENABLED(DELTA)
  357. #error "MESH_BED_LEVELING does not yet support DELTA printers."
  358. #elif MESH_NUM_X_POINTS > 9 || MESH_NUM_Y_POINTS > 9
  359. #error "MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS must be less than 10."
  360. #endif
  361. #elif ENABLED(MANUAL_BED_LEVELING)
  362. #error "MANUAL_BED_LEVELING only applies to MESH_BED_LEVELING."
  363. #endif
  364. /**
  365. * Probes
  366. */
  367. #if PROBE_SELECTED
  368. /**
  369. * Allow only one probe option to be defined
  370. */
  371. #define COUNT_PROBE_1 0
  372. #if ENABLED(FIX_MOUNTED_PROBE)
  373. #define COUNT_PROBE_2 INCREMENT(COUNT_PROBE_1)
  374. #else
  375. #define COUNT_PROBE_2 COUNT_PROBE_1
  376. #endif
  377. #if HAS_Z_SERVO_ENDSTOP && DISABLED(BLTOUCH)
  378. #define COUNT_PROBE_3 INCREMENT(COUNT_PROBE_2)
  379. #else
  380. #define COUNT_PROBE_3 COUNT_PROBE_2
  381. #endif
  382. #if ENABLED(BLTOUCH)
  383. #define COUNT_PROBE_4 INCREMENT(COUNT_PROBE_3)
  384. #else
  385. #define COUNT_PROBE_4 COUNT_PROBE_3
  386. #endif
  387. #if ENABLED(Z_PROBE_ALLEN_KEY)
  388. #define COUNT_PROBE_5 INCREMENT(COUNT_PROBE_4)
  389. #else
  390. #define COUNT_PROBE_5 COUNT_PROBE_4
  391. #endif
  392. #if ENABLED(Z_PROBE_SLED)
  393. #define COUNT_PROBE_6 INCREMENT(COUNT_PROBE_5)
  394. #else
  395. #define COUNT_PROBE_6 COUNT_PROBE_5
  396. #endif
  397. #if COUNT_PROBE_6 > 1
  398. #error "Please enable only one probe: FIX_MOUNTED_PROBE, Z Servo, BLTOUCH, Z_PROBE_ALLEN_KEY, or Z_PROBE_SLED."
  399. #endif
  400. /**
  401. * Z_PROBE_SLED is incompatible with DELTA
  402. */
  403. #if ENABLED(Z_PROBE_SLED) && ENABLED(DELTA)
  404. #error "You cannot use Z_PROBE_SLED with DELTA."
  405. #endif
  406. /**
  407. * NUM_SERVOS is required for a Z servo probe
  408. */
  409. #if HAS_Z_SERVO_ENDSTOP
  410. #ifndef NUM_SERVOS
  411. #error "You must set NUM_SERVOS for a Z servo probe (Z_ENDSTOP_SERVO_NR)."
  412. #elif Z_ENDSTOP_SERVO_NR >= NUM_SERVOS
  413. #error "Z_ENDSTOP_SERVO_NR must be smaller than NUM_SERVOS."
  414. #endif
  415. #endif
  416. /**
  417. * Require pin options and pins to be defined
  418. */
  419. #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
  420. #if ENABLED(Z_MIN_PROBE_ENDSTOP)
  421. #error "Enable only one option: Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN."
  422. #elif DISABLED(USE_ZMIN_PLUG)
  423. #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled."
  424. #elif !HAS_Z_MIN
  425. #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined."
  426. #elif ENABLED(Z_MIN_PROBE_ENDSTOP_INVERTING) != ENABLED(Z_MIN_ENDSTOP_INVERTING)
  427. #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match Z_MIN_PROBE_ENDSTOP_INVERTING."
  428. #endif
  429. #elif ENABLED(Z_MIN_PROBE_ENDSTOP)
  430. #if !HAS_Z_MIN_PROBE_PIN
  431. #error "Z_MIN_PROBE_ENDSTOP requires the Z_MIN_PROBE_PIN to be defined."
  432. #endif
  433. #else
  434. #error "You must enable either Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use a probe."
  435. #endif
  436. /**
  437. * Make sure Z raise values are set
  438. */
  439. #if !defined(Z_CLEARANCE_DEPLOY_PROBE)
  440. #error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration."
  441. #elif !defined(Z_CLEARANCE_BETWEEN_PROBES)
  442. #error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration."
  443. #elif Z_CLEARANCE_DEPLOY_PROBE < 0
  444. #error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0."
  445. #elif Z_CLEARANCE_BETWEEN_PROBES < 0
  446. #error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0."
  447. #endif
  448. #else
  449. /**
  450. * Require some kind of probe for bed leveling and probe testing
  451. */
  452. #if HAS_ABL
  453. #error "Auto Bed Leveling requires a probe! Define a Z Servo, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
  454. #elif ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
  455. #error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe! Define a Z Servo, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
  456. #endif
  457. #endif
  458. /**
  459. * Homing Bump
  460. */
  461. #if X_HOME_BUMP_MM < 0 || Y_HOME_BUMP_MM < 0 || Z_HOME_BUMP_MM < 0
  462. #error "[XYZ]_HOME_BUMP_MM must be greater than or equal to 0."
  463. #endif
  464. /**
  465. * Make sure Z_SAFE_HOMING point is reachable
  466. */
  467. #if ENABLED(Z_SAFE_HOMING)
  468. #if Z_SAFE_HOMING_X_POINT < MIN_PROBE_X || Z_SAFE_HOMING_X_POINT > MAX_PROBE_X
  469. #if HAS_BED_PROBE
  470. #error "Z_SAFE_HOMING_X_POINT can't be reached by the Z probe."
  471. #else
  472. #error "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle."
  473. #endif
  474. #elif Z_SAFE_HOMING_Y_POINT < MIN_PROBE_Y || Z_SAFE_HOMING_Y_POINT > MAX_PROBE_Y
  475. #if HAS_BED_PROBE
  476. #error "Z_SAFE_HOMING_Y_POINT can't be reached by the Z probe."
  477. #else
  478. #error "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle."
  479. #endif
  480. #endif
  481. #endif // Z_SAFE_HOMING
  482. /**
  483. * Auto Bed Leveling
  484. */
  485. #if HAS_ABL
  486. #if ENABLED(USE_RAW_KINEMATICS)
  487. #error "USE_RAW_KINEMATICS is not compatible with AUTO_BED_LEVELING"
  488. #endif
  489. /**
  490. * Delta and SCARA have limited bed leveling options
  491. */
  492. #if DISABLED(AUTO_BED_LEVELING_BILINEAR)
  493. #if ENABLED(DELTA)
  494. #error "Only AUTO_BED_LEVELING_BILINEAR is supported for DELTA bed leveling."
  495. #elif ENABLED(SCARA)
  496. #error "Only AUTO_BED_LEVELING_BILINEAR is supported for SCARA bed leveling."
  497. #endif
  498. #endif
  499. /**
  500. * Check if Probe_Offset * Grid Points is greater than Probing Range
  501. */
  502. #if ABL_GRID
  503. #ifndef DELTA_PROBEABLE_RADIUS
  504. // Be sure points are in the right order
  505. #if LEFT_PROBE_BED_POSITION > RIGHT_PROBE_BED_POSITION
  506. #error "LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION."
  507. #elif FRONT_PROBE_BED_POSITION > BACK_PROBE_BED_POSITION
  508. #error "FRONT_PROBE_BED_POSITION must be less than BACK_PROBE_BED_POSITION."
  509. #endif
  510. // Make sure probing points are reachable
  511. #if LEFT_PROBE_BED_POSITION < MIN_PROBE_X
  512. #error "The given LEFT_PROBE_BED_POSITION can't be reached by the Z probe."
  513. #elif RIGHT_PROBE_BED_POSITION > MAX_PROBE_X
  514. #error "The given RIGHT_PROBE_BED_POSITION can't be reached by the Z probe."
  515. #elif FRONT_PROBE_BED_POSITION < MIN_PROBE_Y
  516. #error "The given FRONT_PROBE_BED_POSITION can't be reached by the Z probe."
  517. #elif BACK_PROBE_BED_POSITION > MAX_PROBE_Y
  518. #error "The given BACK_PROBE_BED_POSITION can't be reached by the Z probe."
  519. #endif
  520. #endif
  521. #else // !ABL_GRID
  522. // Check the triangulation points
  523. #if ABL_PROBE_PT_1_X < MIN_PROBE_X || ABL_PROBE_PT_1_X > MAX_PROBE_X
  524. #error "The given ABL_PROBE_PT_1_X can't be reached by the Z probe."
  525. #elif ABL_PROBE_PT_2_X < MIN_PROBE_X || ABL_PROBE_PT_2_X > MAX_PROBE_X
  526. #error "The given ABL_PROBE_PT_2_X can't be reached by the Z probe."
  527. #elif ABL_PROBE_PT_3_X < MIN_PROBE_X || ABL_PROBE_PT_3_X > MAX_PROBE_X
  528. #error "The given ABL_PROBE_PT_3_X can't be reached by the Z probe."
  529. #elif ABL_PROBE_PT_1_Y < MIN_PROBE_Y || ABL_PROBE_PT_1_Y > MAX_PROBE_Y
  530. #error "The given ABL_PROBE_PT_1_Y can't be reached by the Z probe."
  531. #elif ABL_PROBE_PT_2_Y < MIN_PROBE_Y || ABL_PROBE_PT_2_Y > MAX_PROBE_Y
  532. #error "The given ABL_PROBE_PT_2_Y can't be reached by the Z probe."
  533. #elif ABL_PROBE_PT_3_Y < MIN_PROBE_Y || ABL_PROBE_PT_3_Y > MAX_PROBE_Y
  534. #error "The given ABL_PROBE_PT_3_Y can't be reached by the Z probe."
  535. #endif
  536. #endif // !ABL_GRID
  537. #endif // HAS_ABL
  538. /**
  539. * Advance Extrusion
  540. */
  541. #if ENABLED(ADVANCE) && ENABLED(LIN_ADVANCE)
  542. #error "You can enable ADVANCE or LIN_ADVANCE, but not both."
  543. #endif
  544. /**
  545. * Filament Width Sensor
  546. */
  547. #if ENABLED(FILAMENT_WIDTH_SENSOR) && !HAS_FILAMENT_WIDTH_SENSOR
  548. #error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined."
  549. #endif
  550. /**
  551. * ULTIPANEL encoder
  552. */
  553. #if ENABLED(ULTIPANEL) && DISABLED(NEWPANEL) && DISABLED(SR_LCD_2W_NL) && !defined(SHIFT_CLK)
  554. #error "ULTIPANEL requires some kind of encoder."
  555. #endif
  556. #if ENCODER_PULSES_PER_STEP < 0
  557. #error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead."
  558. #endif
  559. /**
  560. * SAV_3DGLCD display options
  561. */
  562. #if ENABLED(U8GLIB_SSD1306) && ENABLED(U8GLIB_SH1106)
  563. #error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
  564. #endif
  565. /**
  566. * Don't set more than one kinematic type
  567. */
  568. #define COUNT_KIN_1 0
  569. #if ENABLED(DELTA)
  570. #define COUNT_KIN_2 INCREMENT(COUNT_KIN_1)
  571. #else
  572. #define COUNT_KIN_2 COUNT_KIN_1
  573. #endif
  574. #if ENABLED(MORGAN_SCARA)
  575. #define COUNT_KIN_3 INCREMENT(COUNT_KIN_2)
  576. #else
  577. #define COUNT_KIN_3 COUNT_KIN_2
  578. #endif
  579. #if ENABLED(MAKERARM_SCARA)
  580. #define COUNT_KIN_4 INCREMENT(COUNT_KIN_3)
  581. #else
  582. #define COUNT_KIN_4 COUNT_KIN_3
  583. #endif
  584. #if ENABLED(COREXY)
  585. #define COUNT_KIN_5 INCREMENT(COUNT_KIN_4)
  586. #else
  587. #define COUNT_KIN_5 COUNT_KIN_4
  588. #endif
  589. #if ENABLED(COREXZ)
  590. #define COUNT_KIN_6 INCREMENT(COUNT_KIN_5)
  591. #else
  592. #define COUNT_KIN_6 COUNT_KIN_5
  593. #endif
  594. #if ENABLED(COREYZ)
  595. #define COUNT_KIN_7 INCREMENT(COUNT_KIN_6)
  596. #else
  597. #define COUNT_KIN_7 COUNT_KIN_6
  598. #endif
  599. #if ENABLED(COREYX)
  600. #define COUNT_KIN_8 INCREMENT(COUNT_KIN_7)
  601. #else
  602. #define COUNT_KIN_8 COUNT_KIN_7
  603. #endif
  604. #if ENABLED(COREZX)
  605. #define COUNT_KIN_9 INCREMENT(COUNT_KIN_8)
  606. #else
  607. #define COUNT_KIN_9 COUNT_KIN_8
  608. #endif
  609. #if ENABLED(COREZY)
  610. #define COUNT_KIN_10 INCREMENT(COUNT_KIN_9)
  611. #else
  612. #define COUNT_KIN_10 COUNT_KIN_9
  613. #endif
  614. #if COUNT_KIN_10 > 1
  615. #error "Please enable only one of DELTA, MORGAN_SCARA, MAKERARM_SCARA, COREXY, COREYX, COREXZ, COREZX, COREYZ, or COREZY."
  616. #endif
  617. /**
  618. * Allen Key
  619. * Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis.
  620. */
  621. #if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
  622. #error "You can't home to a z min endstop with a Z_PROBE_ALLEN_KEY"
  623. #endif
  624. /**
  625. * Dual X Carriage requirements
  626. */
  627. #if ENABLED(DUAL_X_CARRIAGE)
  628. #if EXTRUDERS == 1
  629. #error "DUAL_X_CARRIAGE requires 2 (or more) extruders."
  630. #elif CORE_IS_XY || CORE_IS_XZ
  631. #error "DUAL_X_CARRIAGE cannot be used with COREXY, COREYX, COREXZ, or COREZX."
  632. #elif !HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR
  633. #error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined."
  634. #elif !HAS_X_MAX
  635. #error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop."
  636. #elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS)
  637. #error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS."
  638. #elif X_HOME_DIR != -1 || X2_HOME_DIR != 1
  639. #error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1."
  640. #endif
  641. #endif // DUAL_X_CARRIAGE
  642. /**
  643. * Make sure auto fan pins don't conflict with the fan pin
  644. */
  645. #if HAS_AUTO_FAN
  646. #if HAS_FAN0
  647. #if E0_AUTO_FAN_PIN == FAN_PIN
  648. #error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN."
  649. #elif E1_AUTO_FAN_PIN == FAN_PIN
  650. #error "You cannot set E1_AUTO_FAN_PIN equal to FAN_PIN."
  651. #elif E2_AUTO_FAN_PIN == FAN_PIN
  652. #error "You cannot set E2_AUTO_FAN_PIN equal to FAN_PIN."
  653. #elif E3_AUTO_FAN_PIN == FAN_PIN
  654. #error "You cannot set E3_AUTO_FAN_PIN equal to FAN_PIN."
  655. #endif
  656. #endif
  657. #endif
  658. #if HAS_FAN0 && CONTROLLERFAN_PIN == FAN_PIN
  659. #error "You cannot set CONTROLLERFAN_PIN equal to FAN_PIN."
  660. #endif
  661. #if HAS_CONTROLLERFAN
  662. #if E0_AUTO_FAN_PIN == CONTROLLERFAN_PIN
  663. #error "You cannot set E0_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
  664. #elif E1_AUTO_FAN_PIN == CONTROLLERFAN_PIN
  665. #error "You cannot set E1_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
  666. #elif E2_AUTO_FAN_PIN == CONTROLLERFAN_PIN
  667. #error "You cannot set E2_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
  668. #elif E3_AUTO_FAN_PIN == CONTROLLERFAN_PIN
  669. #error "You cannot set E3_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
  670. #endif
  671. #endif
  672. /**
  673. * Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set.
  674. */
  675. #if !HAS_HEATER_0
  676. #error "HEATER_0_PIN not defined for this board."
  677. #elif !PIN_EXISTS(TEMP_0)
  678. #error "TEMP_0_PIN not defined for this board."
  679. #elif !PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE)
  680. #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
  681. #elif TEMP_SENSOR_0 == 0
  682. #error "TEMP_SENSOR_0 is required."
  683. #endif
  684. #if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)
  685. #if !HAS_HEATER_1
  686. #error "HEATER_1_PIN not defined for this board."
  687. #endif
  688. #endif
  689. #if HOTENDS > 1
  690. #if TEMP_SENSOR_1 == 0
  691. #error "TEMP_SENSOR_1 is required with 2 or more HOTENDS."
  692. #elif !PIN_EXISTS(TEMP_1)
  693. #error "TEMP_1_PIN not defined for this board."
  694. #endif
  695. #if HOTENDS > 2
  696. #if TEMP_SENSOR_2 == 0
  697. #error "TEMP_SENSOR_2 is required with 3 or more HOTENDS."
  698. #elif !HAS_HEATER_2
  699. #error "HEATER_2_PIN not defined for this board."
  700. #elif !PIN_EXISTS(TEMP_2)
  701. #error "TEMP_2_PIN not defined for this board."
  702. #endif
  703. #if HOTENDS > 3
  704. #if TEMP_SENSOR_3 == 0
  705. #error "TEMP_SENSOR_3 is required with 4 HOTENDS."
  706. #elif !HAS_HEATER_3
  707. #error "HEATER_3_PIN not defined for this board."
  708. #elif !PIN_EXISTS(TEMP_3)
  709. #error "TEMP_3_PIN not defined for this board."
  710. #endif
  711. #elif TEMP_SENSOR_3 != 0
  712. #error "TEMP_SENSOR_3 shouldn't be set with only 3 extruders."
  713. #endif
  714. #elif TEMP_SENSOR_2 != 0
  715. #error "TEMP_SENSOR_2 shouldn't be set with only 2 extruders."
  716. #elif TEMP_SENSOR_3 != 0
  717. #error "TEMP_SENSOR_3 shouldn't be set with only 2 extruders."
  718. #endif
  719. #elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT)
  720. #error "TEMP_SENSOR_1 shouldn't be set with only 1 extruder."
  721. #elif TEMP_SENSOR_2 != 0
  722. #error "TEMP_SENSOR_2 shouldn't be set with only 1 extruder."
  723. #elif TEMP_SENSOR_3 != 0
  724. #error "TEMP_SENSOR_3 shouldn't be set with only 1 extruder."
  725. #endif
  726. #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0
  727. #error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT."
  728. #endif
  729. /**
  730. * Temperature status LEDs
  731. */
  732. #if ENABLED(TEMP_STAT_LEDS) && !PIN_EXISTS(STAT_LED_RED) && !PIN_EXISTS(STAT_LED_BLUE)
  733. #error "TEMP_STAT_LEDS requires STAT_LED_RED_PIN or STAT_LED_BLUE_PIN, preferably both."
  734. #endif
  735. /**
  736. * Basic 2-nozzle duplication mode
  737. */
  738. #if ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
  739. #if HOTENDS != 2
  740. #error "DUAL_NOZZLE_DUPLICATION_MODE requires exactly 2 hotends."
  741. #elif ENABLED(DUAL_X_CARRIAGE)
  742. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with DUAL_X_CARRIAGE."
  743. #elif ENABLED(SINGLENOZZLE)
  744. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SINGLENOZZLE."
  745. #elif ENABLED(MIXING_EXTRUDER)
  746. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with MIXING_EXTRUDER."
  747. #elif ENABLED(SWITCHING_EXTRUDER)
  748. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SWITCHING_EXTRUDER."
  749. #endif
  750. #endif
  751. /**
  752. * Test Extruder Pins
  753. */
  754. #if EXTRUDERS > 3
  755. #if !PIN_EXISTS(E3_STEP) || !PIN_EXISTS(E3_DIR) || !PIN_EXISTS(E3_ENABLE)
  756. #error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board."
  757. #endif
  758. #elif EXTRUDERS > 2
  759. #if !PIN_EXISTS(E2_STEP) || !PIN_EXISTS(E2_DIR) || !PIN_EXISTS(E2_ENABLE)
  760. #error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board."
  761. #endif
  762. #elif EXTRUDERS > 1
  763. #if !PIN_EXISTS(E1_STEP) || !PIN_EXISTS(E1_DIR) || !PIN_EXISTS(E1_ENABLE)
  764. #error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board."
  765. #endif
  766. #endif
  767. /**
  768. * Endstops
  769. */
  770. #if DISABLED(USE_XMIN_PLUG) && DISABLED(USE_XMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _XMAX_ && Z2_USE_ENDSTOP <= _XMIN_)
  771. #error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG."
  772. #elif DISABLED(USE_YMIN_PLUG) && DISABLED(USE_YMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _YMAX_ && Z2_USE_ENDSTOP <= _YMIN_)
  773. #error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG."
  774. #elif DISABLED(USE_ZMIN_PLUG) && DISABLED(USE_ZMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _ZMAX_ && Z2_USE_ENDSTOP <= _ZMIN_)
  775. #error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG."
  776. #elif ENABLED(Z_DUAL_ENDSTOPS)
  777. #if !Z2_USE_ENDSTOP
  778. #error "You must set Z2_USE_ENDSTOP with Z_DUAL_ENDSTOPS."
  779. #elif ENABLED(DELTA)
  780. #error "Z_DUAL_ENDSTOPS is not compatible with DELTA."
  781. #endif
  782. #elif !IS_SCARA
  783. #if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG)
  784. #error "Enable USE_XMIN_PLUG when homing X to MIN."
  785. #elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG)
  786. #error "Enable USE_XMAX_PLUG when homing X to MAX."
  787. #elif Y_HOME_DIR < 0 && DISABLED(USE_YMIN_PLUG)
  788. #error "Enable USE_YMIN_PLUG when homing Y to MIN."
  789. #elif Y_HOME_DIR > 0 && DISABLED(USE_YMAX_PLUG)
  790. #error "Enable USE_YMAX_PLUG when homing Y to MAX."
  791. #elif Z_HOME_DIR < 0 && DISABLED(USE_ZMIN_PLUG)
  792. #error "Enable USE_ZMIN_PLUG when homing Z to MIN."
  793. #elif Z_HOME_DIR > 0 && DISABLED(USE_ZMAX_PLUG)
  794. #error "Enable USE_ZMAX_PLUG when homing Z to MAX."
  795. #endif
  796. #endif
  797. /**
  798. * emergency-command parser
  799. */
  800. #if ENABLED(EMERGENCY_PARSER) && defined(USBCON)
  801. #error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)."
  802. #endif
  803. /**
  804. * I2C bus
  805. */
  806. #if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0
  807. #if I2C_SLAVE_ADDRESS < 8
  808. #error "I2C_SLAVE_ADDRESS can't be less than 8. (Addresses 0 - 7 are reserved.)"
  809. #elif I2C_SLAVE_ADDRESS > 127
  810. #error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)"
  811. #endif
  812. #endif
  813. /**
  814. * G38 Probe Target
  815. */
  816. #if ENABLED(G38_PROBE_TARGET)
  817. #if !HAS_BED_PROBE
  818. #error "G38_PROBE_TARGET requires a bed probe."
  819. #elif !IS_CARTESIAN
  820. #error "G38_PROBE_TARGET requires a Cartesian machine."
  821. #endif
  822. #endif
  823. /**
  824. * RGB_LED Requirements
  825. */
  826. #if ENABLED(RGB_LED)
  827. #if !(PIN_EXISTS(RGB_LED_R) && PIN_EXISTS(RGB_LED_G) && PIN_EXISTS(RGB_LED_B))
  828. #error "RGB_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, and RGB_LED_B_PIN."
  829. #elif ENABLED(BLINKM)
  830. #error "RGB_LED and BLINKM are currently incompatible (both use M150)."
  831. #endif
  832. #endif
  833. /**
  834. * Auto Fan check for PWM pins
  835. */
  836. #if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255
  837. #define AF_ERR_SUFF "_AUTO_FAN_PIN is not a PWM pin. Set EXTRUDER_AUTO_FAN_SPEED to 255."
  838. #if HAS_AUTO_FAN_0
  839. static_assert(GET_TIMER(E0_AUTO_FAN_PIN), "E0" AF_ERR_SUFF);
  840. #elif HAS_AUTO_FAN_1
  841. static_assert(GET_TIMER(E1_AUTO_FAN_PIN), "E1" AF_ERR_SUFF);
  842. #elif HAS_AUTO_FAN_2
  843. static_assert(GET_TIMER(E2_AUTO_FAN_PIN), "E2" AF_ERR_SUFF);
  844. #elif HAS_AUTO_FAN_3
  845. static_assert(GET_TIMER(E3_AUTO_FAN_PIN), "E3" AF_ERR_SUFF);
  846. #endif
  847. #endif
  848. /**
  849. * Make sure only one display is enabled
  850. *
  851. * Note: BQ_LCD_SMART_CONTROLLER => REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  852. * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER => REPRAP_DISCOUNT_SMART_CONTROLLER
  853. * SAV_3DGLCD => U8GLIB_SH1106 => ULTIMAKERCONTROLLER
  854. * miniVIKI => ULTIMAKERCONTROLLER
  855. * VIKI2 => ULTIMAKERCONTROLLER
  856. * ELB_FULL_GRAPHIC_CONTROLLER => ULTIMAKERCONTROLLER
  857. * PANEL_ONE => ULTIMAKERCONTROLLER
  858. */
  859. #define COUNT_LCD_1 0
  860. #if ENABLED(ULTIMAKERCONTROLLER) \
  861. && DISABLED(SAV_3DGLCD) && DISABLED(miniVIKI) && DISABLED(VIKI2) \
  862. && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) && DISABLED(PANEL_ONE)
  863. #define COUNT_LCD_2 INCREMENT(COUNT_LCD_1)
  864. #else
  865. #define COUNT_LCD_2 COUNT_LCD_1
  866. #endif
  867. #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
  868. #define COUNT_LCD_3 INCREMENT(COUNT_LCD_2)
  869. #else
  870. #define COUNT_LCD_3 COUNT_LCD_2
  871. #endif
  872. #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(BQ_LCD_SMART_CONTROLLER)
  873. #define COUNT_LCD_4 INCREMENT(COUNT_LCD_3)
  874. #else
  875. #define COUNT_LCD_4 COUNT_LCD_3
  876. #endif
  877. #if ENABLED(CARTESIO_UI)
  878. #define COUNT_LCD_5 INCREMENT(COUNT_LCD_4)
  879. #else
  880. #define COUNT_LCD_5 COUNT_LCD_4
  881. #endif
  882. #if ENABLED(PANEL_ONE)
  883. #define COUNT_LCD_6 INCREMENT(COUNT_LCD_5)
  884. #else
  885. #define COUNT_LCD_6 COUNT_LCD_5
  886. #endif
  887. #if ENABLED(MAKRPANEL)
  888. #define COUNT_LCD_7 INCREMENT(COUNT_LCD_6)
  889. #else
  890. #define COUNT_LCD_7 COUNT_LCD_6
  891. #endif
  892. #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
  893. #define COUNT_LCD_8 INCREMENT(COUNT_LCD_7)
  894. #else
  895. #define COUNT_LCD_8 COUNT_LCD_7
  896. #endif
  897. #if ENABLED(VIKI2)
  898. #define COUNT_LCD_9 INCREMENT(COUNT_LCD_8)
  899. #else
  900. #define COUNT_LCD_9 COUNT_LCD_8
  901. #endif
  902. #if ENABLED(miniVIKI)
  903. #define COUNT_LCD_10 INCREMENT(COUNT_LCD_9)
  904. #else
  905. #define COUNT_LCD_10 COUNT_LCD_9
  906. #endif
  907. #if ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
  908. #define COUNT_LCD_11 INCREMENT(COUNT_LCD_10)
  909. #else
  910. #define COUNT_LCD_11 COUNT_LCD_10
  911. #endif
  912. #if ENABLED(G3D_PANEL)
  913. #define COUNT_LCD_12 INCREMENT(COUNT_LCD_11)
  914. #else
  915. #define COUNT_LCD_12 COUNT_LCD_11
  916. #endif
  917. #if ENABLED(MINIPANEL)
  918. #define COUNT_LCD_13 INCREMENT(COUNT_LCD_12)
  919. #else
  920. #define COUNT_LCD_13 COUNT_LCD_12
  921. #endif
  922. #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI)
  923. #define COUNT_LCD_14 INCREMENT(COUNT_LCD_13)
  924. #else
  925. #define COUNT_LCD_14 COUNT_LCD_13
  926. #endif
  927. #if ENABLED(RIGIDBOT_PANEL)
  928. #define COUNT_LCD_15 INCREMENT(COUNT_LCD_14)
  929. #else
  930. #define COUNT_LCD_15 COUNT_LCD_14
  931. #endif
  932. #if ENABLED(RA_CONTROL_PANEL)
  933. #define COUNT_LCD_16 INCREMENT(COUNT_LCD_15)
  934. #else
  935. #define COUNT_LCD_16 COUNT_LCD_15
  936. #endif
  937. #if ENABLED(LCD_I2C_SAINSMART_YWROBOT)
  938. #define COUNT_LCD_17 INCREMENT(COUNT_LCD_16)
  939. #else
  940. #define COUNT_LCD_17 COUNT_LCD_16
  941. #endif
  942. #if ENABLED(LCM1602)
  943. #define COUNT_LCD_18 INCREMENT(COUNT_LCD_17)
  944. #else
  945. #define COUNT_LCD_18 COUNT_LCD_17
  946. #endif
  947. #if ENABLED(LCD_I2C_PANELOLU2)
  948. #define COUNT_LCD_19 INCREMENT(COUNT_LCD_18)
  949. #else
  950. #define COUNT_LCD_19 COUNT_LCD_18
  951. #endif
  952. #if ENABLED(LCD_I2C_VIKI)
  953. #define COUNT_LCD_20 INCREMENT(COUNT_LCD_19)
  954. #else
  955. #define COUNT_LCD_20 COUNT_LCD_19
  956. #endif
  957. #if ENABLED(U8GLIB_SSD1306)
  958. #define COUNT_LCD_21 INCREMENT(COUNT_LCD_20)
  959. #else
  960. #define COUNT_LCD_21 COUNT_LCD_20
  961. #endif
  962. #if ENABLED(SAV_3DLCD)
  963. #define COUNT_LCD_22 INCREMENT(COUNT_LCD_21)
  964. #else
  965. #define COUNT_LCD_22 COUNT_LCD_21
  966. #endif
  967. #if ENABLED(BQ_LCD_SMART_CONTROLLER)
  968. #define COUNT_LCD_23 INCREMENT(COUNT_LCD_22)
  969. #else
  970. #define COUNT_LCD_23 COUNT_LCD_22
  971. #endif
  972. #if ENABLED(SAV_3DGLCD)
  973. #define COUNT_LCD_24 INCREMENT(COUNT_LCD_23)
  974. #else
  975. #define COUNT_LCD_24 COUNT_LCD_23
  976. #endif
  977. #if COUNT_LCD_24 > 1
  978. #error "Please select no more than one LCD controller option."
  979. #endif