My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration.h 95KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720172117221723172417251726172717281729173017311732173317341735173617371738173917401741174217431744174517461747174817491750175117521753175417551756175717581759176017611762176317641765176617671768176917701771177217731774177517761777177817791780178117821783178417851786178717881789179017911792179317941795179617971798179918001801180218031804180518061807180818091810181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391840184118421843184418451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906190719081909191019111912191319141915191619171918191919201921192219231924192519261927192819291930193119321933193419351936193719381939194019411942194319441945194619471948194919501951195219531954195519561957195819591960196119621963196419651966196719681969197019711972197319741975197619771978197919801981198219831984198519861987198819891990199119921993199419951996199719981999200020012002200320042005200620072008200920102011201220132014201520162017201820192020202120222023202420252026202720282029203020312032203320342035203620372038203920402041204220432044204520462047204820492050205120522053205420552056205720582059206020612062206320642065206620672068206920702071207220732074207520762077207820792080208120822083208420852086208720882089209020912092209320942095209620972098209921002101210221032104210521062107210821092110211121122113211421152116211721182119212021212122212321242125212621272128212921302131213221332134213521362137213821392140214121422143214421452146214721482149215021512152215321542155215621572158215921602161216221632164216521662167216821692170217121722173217421752176217721782179218021812182218321842185218621872188218921902191219221932194219521962197219821992200220122022203220422052206220722082209221022112212221322142215221622172218221922202221222222232224222522262227222822292230223122322233223422352236223722382239224022412242224322442245224622472248224922502251225222532254225522562257225822592260226122622263226422652266226722682269227022712272227322742275227622772278227922802281228222832284228522862287228822892290229122922293229422952296229722982299230023012302230323042305230623072308230923102311231223132314231523162317231823192320232123222323232423252326232723282329233023312332233323342335233623372338233923402341234223432344234523462347234823492350235123522353235423552356235723582359236023612362236323642365236623672368236923702371237223732374237523762377237823792380238123822383238423852386238723882389239023912392239323942395239623972398239924002401240224032404240524062407240824092410241124122413241424152416241724182419242024212422242324242425242624272428242924302431243224332434243524362437243824392440244124422443244424452446244724482449245024512452245324542455245624572458245924602461246224632464246524662467246824692470247124722473247424752476247724782479248024812482248324842485248624872488248924902491249224932494249524962497249824992500250125022503250425052506250725082509251025112512251325142515251625172518251925202521252225232524252525262527252825292530253125322533253425352536253725382539254025412542254325442545254625472548254925502551255225532554255525562557255825592560256125622563256425652566256725682569257025712572257325742575257625772578257925802581258225832584258525862587258825892590259125922593259425952596259725982599260026012602260326042605260626072608260926102611
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. */
  37. #define CONFIGURATION_H_VERSION 020008
  38. //===========================================================================
  39. //============================= Getting Started =============================
  40. //===========================================================================
  41. /**
  42. * Here are some standard links for getting your machine calibrated:
  43. *
  44. * https://reprap.org/wiki/Calibration
  45. * https://youtu.be/wAL9d7FgInk
  46. * http://calculator.josefprusa.cz
  47. * https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  48. * https://www.thingiverse.com/thing:5573
  49. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  50. * https://www.thingiverse.com/thing:298812
  51. */
  52. //===========================================================================
  53. //============================= DELTA Printer ===============================
  54. //===========================================================================
  55. // For a Delta printer, start with one of the configuration files in the config/examples/delta directory
  56. // from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine.
  57. //
  58. //===========================================================================
  59. //============================= SCARA Printer ===============================
  60. //===========================================================================
  61. // For a SCARA printer, start with one of the configuration files in the config/examples/SCARA directory
  62. // from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine.
  63. //
  64. // @section info
  65. // Author info of this build printed to the host during boot and M115
  66. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  67. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  68. /**
  69. * *** VENDORS PLEASE READ ***
  70. *
  71. * Marlin allows you to add a custom boot image for Graphical LCDs.
  72. * With this option Marlin will first show your custom screen followed
  73. * by the standard Marlin logo with version number and web URL.
  74. *
  75. * We encourage you to take advantage of this new feature and we also
  76. * respectfully request that you retain the unmodified Marlin boot screen.
  77. */
  78. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  79. #define SHOW_BOOTSCREEN
  80. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  81. //#define SHOW_CUSTOM_BOOTSCREEN
  82. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  83. //#define CUSTOM_STATUS_SCREEN_IMAGE
  84. // @section machine
  85. /**
  86. * Select the serial port on the board to use for communication with the host.
  87. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  88. * Serial port -1 is the USB emulated serial port, if available.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT 0
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  97. * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  98. */
  99. //#define SERIAL_PORT_2 -1
  100. /**
  101. * This setting determines the communication speed of the printer.
  102. *
  103. * 250000 works in most cases, but you might try a lower speed if
  104. * you commonly experience drop-outs during host printing.
  105. * You may try up to 1000000 to speed up SD file transfer.
  106. *
  107. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  108. */
  109. #define BAUDRATE 250000
  110. // Enable the Bluetooth serial interface on AT90USB devices
  111. //#define BLUETOOTH
  112. // Choose the name from boards.h that matches your setup
  113. #ifndef MOTHERBOARD
  114. #define MOTHERBOARD BOARD_RAMPS_14_EFB
  115. #endif
  116. // Name displayed in the LCD "Ready" message and Info menu
  117. //#define CUSTOM_MACHINE_NAME "3D Printer"
  118. // Printer's unique ID, used by some programs to differentiate between machines.
  119. // Choose your own or use a service like https://www.uuidgenerator.net/version4
  120. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  121. // @section extruder
  122. // This defines the number of extruders
  123. // :[0, 1, 2, 3, 4, 5, 6, 7, 8]
  124. #define EXTRUDERS 1
  125. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  126. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  127. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  128. //#define SINGLENOZZLE
  129. // Save and restore temperature and fan speed on tool-change.
  130. // Set standby for the unselected tool with M104/106/109 T...
  131. #if ENABLED(SINGLENOZZLE)
  132. //#define SINGLENOZZLE_STANDBY_TEMP
  133. //#define SINGLENOZZLE_STANDBY_FAN
  134. #endif
  135. /**
  136. * Multi-Material Unit
  137. * Set to one of these predefined models:
  138. *
  139. * PRUSA_MMU1 : Průša MMU1 (The "multiplexer" version)
  140. * PRUSA_MMU2 : Průša MMU2
  141. * PRUSA_MMU2S : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5)
  142. * SMUFF_EMU_MMU2 : Technik Gegg SMUFF (Průša MMU2 emulation mode)
  143. * SMUFF_EMU_MMU2S : Technik Gegg SMUFF (Průša MMU2S emulation mode)
  144. *
  145. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  146. * See additional options in Configuration_adv.h.
  147. */
  148. //#define MMU_MODEL PRUSA_MMU2
  149. // A dual extruder that uses a single stepper motor
  150. //#define SWITCHING_EXTRUDER
  151. #if ENABLED(SWITCHING_EXTRUDER)
  152. #define SWITCHING_EXTRUDER_SERVO_NR 0
  153. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  154. #if EXTRUDERS > 3
  155. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  156. #endif
  157. #endif
  158. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  159. //#define SWITCHING_NOZZLE
  160. #if ENABLED(SWITCHING_NOZZLE)
  161. #define SWITCHING_NOZZLE_SERVO_NR 0
  162. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  163. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  164. #endif
  165. /**
  166. * Two separate X-carriages with extruders that connect to a moving part
  167. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  168. */
  169. //#define PARKING_EXTRUDER
  170. /**
  171. * Two separate X-carriages with extruders that connect to a moving part
  172. * via a magnetic docking mechanism using movements and no solenoid
  173. *
  174. * project : https://www.thingiverse.com/thing:3080893
  175. * movements : https://youtu.be/0xCEiG9VS3k
  176. * https://youtu.be/Bqbcs0CU2FE
  177. */
  178. //#define MAGNETIC_PARKING_EXTRUDER
  179. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  180. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  181. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  182. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  183. #if ENABLED(PARKING_EXTRUDER)
  184. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  185. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  186. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  187. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  188. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  189. #define MPE_FAST_SPEED 9000 // (mm/min) Speed for travel before last distance point
  190. #define MPE_SLOW_SPEED 4500 // (mm/min) Speed for last distance travel to park and couple
  191. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  192. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  193. #endif
  194. #endif
  195. /**
  196. * Switching Toolhead
  197. *
  198. * Support for swappable and dockable toolheads, such as
  199. * the E3D Tool Changer. Toolheads are locked with a servo.
  200. */
  201. //#define SWITCHING_TOOLHEAD
  202. /**
  203. * Magnetic Switching Toolhead
  204. *
  205. * Support swappable and dockable toolheads with a magnetic
  206. * docking mechanism using movement and no servo.
  207. */
  208. //#define MAGNETIC_SWITCHING_TOOLHEAD
  209. /**
  210. * Electromagnetic Switching Toolhead
  211. *
  212. * Parking for CoreXY / HBot kinematics.
  213. * Toolheads are parked at one edge and held with an electromagnet.
  214. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  215. */
  216. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  217. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  218. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  219. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  220. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  221. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  222. #if ENABLED(SWITCHING_TOOLHEAD)
  223. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  224. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  225. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  226. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  227. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  228. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  229. #if ENABLED(PRIME_BEFORE_REMOVE)
  230. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  231. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  232. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/min) Extruder prime feedrate
  233. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/min) Extruder retract feedrate
  234. #endif
  235. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  236. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  237. #endif
  238. #endif
  239. /**
  240. * "Mixing Extruder"
  241. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  242. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  243. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  244. * - This implementation supports up to two mixing extruders.
  245. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  246. */
  247. //#define MIXING_EXTRUDER
  248. #if ENABLED(MIXING_EXTRUDER)
  249. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  250. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  251. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  252. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  253. #if ENABLED(GRADIENT_MIX)
  254. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  255. #endif
  256. #endif
  257. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  258. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  259. // For the other hotends it is their distance from the extruder 0 hotend.
  260. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  261. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  262. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  263. // @section machine
  264. /**
  265. * Power Supply Control
  266. *
  267. * Enable and connect the power supply to the PS_ON_PIN.
  268. * Specify whether the power supply is active HIGH or active LOW.
  269. */
  270. //#define PSU_CONTROL
  271. //#define PSU_NAME "Power Supply"
  272. #if ENABLED(PSU_CONTROL)
  273. #define PSU_ACTIVE_STATE LOW // Set 'LOW' for ATX, 'HIGH' for X-Box
  274. //#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80
  275. //#define PSU_POWERUP_DELAY 250 // (ms) Delay for the PSU to warm up to full power
  276. //#define PSU_POWERUP_GCODE "M355 S1" // G-code to run after power-on (e.g., case light on)
  277. //#define PSU_POWEROFF_GCODE "M355 S0" // G-code to run before power-off (e.g., case light off)
  278. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  279. #if ENABLED(AUTO_POWER_CONTROL)
  280. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  281. #define AUTO_POWER_E_FANS
  282. #define AUTO_POWER_CONTROLLERFAN
  283. #define AUTO_POWER_CHAMBER_FAN
  284. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU if any extruder is over this temperature
  285. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU if the chamber is over this temperature
  286. #define POWER_TIMEOUT 30 // (s) Turn off power if the machine is idle for this duration
  287. //#define POWER_OFF_DELAY 60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
  288. #endif
  289. #endif
  290. //===========================================================================
  291. //============================= Thermal Settings ============================
  292. //===========================================================================
  293. // @section temperature
  294. /**
  295. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  296. *
  297. * Temperature sensors available:
  298. *
  299. * -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
  300. * -3 : thermocouple with MAX31855 (only for sensors 0-1)
  301. * -2 : thermocouple with MAX6675 (only for sensors 0-1)
  302. * -4 : thermocouple with AD8495
  303. * -1 : thermocouple with AD595
  304. * 0 : not used
  305. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  306. * 331 : (3.3V scaled thermistor 1 table for MEGA)
  307. * 332 : (3.3V scaled thermistor 1 table for DUE)
  308. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  309. * 202 : 200k thermistor - Copymaster 3D
  310. * 3 : Mendel-parts thermistor (4.7k pullup)
  311. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  312. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
  313. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  314. * 502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
  315. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  316. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  317. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  318. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  319. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  320. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  321. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  322. * 11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
  323. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  324. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  325. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  326. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  327. * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
  328. * NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
  329. * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
  330. * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
  331. * 22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
  332. * 23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
  333. * 30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
  334. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  335. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  336. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  337. * 66 : 4.7M High Temperature thermistor from Dyze Design
  338. * 67 : 450C thermistor from SliceEngineering
  339. * 70 : the 100K thermistor found in the bq Hephestos 2
  340. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  341. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  342. *
  343. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  344. * (but gives greater accuracy and more stable PID)
  345. * 51 : 100k thermistor - EPCOS (1k pullup)
  346. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  347. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  348. *
  349. * 1047 : Pt1000 with 4k7 pullup (E3D)
  350. * 1010 : Pt1000 with 1k pullup (non standard)
  351. * 147 : Pt100 with 4k7 pullup
  352. * 110 : Pt100 with 1k pullup (non standard)
  353. *
  354. * 1000 : Custom - Specify parameters in Configuration_adv.h
  355. *
  356. * Use these for Testing or Development purposes. NEVER for production machine.
  357. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  358. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  359. */
  360. #define TEMP_SENSOR_0 1
  361. #define TEMP_SENSOR_1 0
  362. #define TEMP_SENSOR_2 0
  363. #define TEMP_SENSOR_3 0
  364. #define TEMP_SENSOR_4 0
  365. #define TEMP_SENSOR_5 0
  366. #define TEMP_SENSOR_6 0
  367. #define TEMP_SENSOR_7 0
  368. #define TEMP_SENSOR_BED 0
  369. #define TEMP_SENSOR_PROBE 0
  370. #define TEMP_SENSOR_CHAMBER 0
  371. // Dummy thermistor constant temperature readings, for use with 998 and 999
  372. #define DUMMY_THERMISTOR_998_VALUE 25
  373. #define DUMMY_THERMISTOR_999_VALUE 100
  374. // Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
  375. //#define MAX31865_SENSOR_OHMS_0 100 // (Ω) Typically 100 or 1000 (PT100 or PT1000)
  376. //#define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for AdaFruit PT100; 4300 for AdaFruit PT1000
  377. //#define MAX31865_SENSOR_OHMS_1 100
  378. //#define MAX31865_CALIBRATION_OHMS_1 430
  379. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  380. // from the two sensors differ too much the print will be aborted.
  381. //#define TEMP_SENSOR_1_AS_REDUNDANT
  382. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  383. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  384. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  385. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  386. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  387. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  388. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  389. // Below this temperature the heater will be switched off
  390. // because it probably indicates a broken thermistor wire.
  391. #define HEATER_0_MINTEMP 5
  392. #define HEATER_1_MINTEMP 5
  393. #define HEATER_2_MINTEMP 5
  394. #define HEATER_3_MINTEMP 5
  395. #define HEATER_4_MINTEMP 5
  396. #define HEATER_5_MINTEMP 5
  397. #define HEATER_6_MINTEMP 5
  398. #define HEATER_7_MINTEMP 5
  399. #define BED_MINTEMP 5
  400. // Above this temperature the heater will be switched off.
  401. // This can protect components from overheating, but NOT from shorts and failures.
  402. // (Use MINTEMP for thermistor short/failure protection.)
  403. #define HEATER_0_MAXTEMP 275
  404. #define HEATER_1_MAXTEMP 275
  405. #define HEATER_2_MAXTEMP 275
  406. #define HEATER_3_MAXTEMP 275
  407. #define HEATER_4_MAXTEMP 275
  408. #define HEATER_5_MAXTEMP 275
  409. #define HEATER_6_MAXTEMP 275
  410. #define HEATER_7_MAXTEMP 275
  411. #define BED_MAXTEMP 150
  412. //===========================================================================
  413. //============================= PID Settings ================================
  414. //===========================================================================
  415. // PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning
  416. // Comment the following line to disable PID and enable bang-bang.
  417. #define PIDTEMP
  418. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  419. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  420. #define PID_K1 0.95 // Smoothing factor within any PID loop
  421. #if ENABLED(PIDTEMP)
  422. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  423. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  424. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  425. // Set/get with gcode: M301 E[extruder number, 0-2]
  426. #if ENABLED(PID_PARAMS_PER_HOTEND)
  427. // Specify between 1 and HOTENDS values per array.
  428. // If fewer than EXTRUDER values are provided, the last element will be repeated.
  429. #define DEFAULT_Kp_LIST { 22.20, 22.20 }
  430. #define DEFAULT_Ki_LIST { 1.08, 1.08 }
  431. #define DEFAULT_Kd_LIST { 114.00, 114.00 }
  432. #else
  433. #define DEFAULT_Kp 22.20
  434. #define DEFAULT_Ki 1.08
  435. #define DEFAULT_Kd 114.00
  436. #endif
  437. #endif // PIDTEMP
  438. //===========================================================================
  439. //====================== PID > Bed Temperature Control ======================
  440. //===========================================================================
  441. /**
  442. * PID Bed Heating
  443. *
  444. * If this option is enabled set PID constants below.
  445. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  446. *
  447. * The PID frequency will be the same as the extruder PWM.
  448. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  449. * which is fine for driving a square wave into a resistive load and does not significantly
  450. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  451. * heater. If your configuration is significantly different than this and you don't understand
  452. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  453. */
  454. //#define PIDTEMPBED
  455. //#define BED_LIMIT_SWITCHING
  456. /**
  457. * Max Bed Power
  458. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  459. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  460. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  461. */
  462. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  463. #if ENABLED(PIDTEMPBED)
  464. //#define MIN_BED_POWER 0
  465. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  466. // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  467. // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  468. #define DEFAULT_bedKp 10.00
  469. #define DEFAULT_bedKi .023
  470. #define DEFAULT_bedKd 305.4
  471. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  472. #endif // PIDTEMPBED
  473. #if EITHER(PIDTEMP, PIDTEMPBED)
  474. //#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
  475. //#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  476. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  477. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  478. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  479. #endif
  480. // @section extruder
  481. /**
  482. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  483. * Add M302 to set the minimum extrusion temperature and/or turn
  484. * cold extrusion prevention on and off.
  485. *
  486. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  487. */
  488. #define PREVENT_COLD_EXTRUSION
  489. #define EXTRUDE_MINTEMP 170
  490. /**
  491. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  492. * Note: For Bowden Extruders make this large enough to allow load/unload.
  493. */
  494. #define PREVENT_LENGTHY_EXTRUDE
  495. #define EXTRUDE_MAXLENGTH 200
  496. //===========================================================================
  497. //======================== Thermal Runaway Protection =======================
  498. //===========================================================================
  499. /**
  500. * Thermal Protection provides additional protection to your printer from damage
  501. * and fire. Marlin always includes safe min and max temperature ranges which
  502. * protect against a broken or disconnected thermistor wire.
  503. *
  504. * The issue: If a thermistor falls out, it will report the much lower
  505. * temperature of the air in the room, and the the firmware will keep
  506. * the heater on.
  507. *
  508. * If you get "Thermal Runaway" or "Heating failed" errors the
  509. * details can be tuned in Configuration_adv.h
  510. */
  511. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  512. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  513. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  514. //===========================================================================
  515. //============================= Mechanical Settings =========================
  516. //===========================================================================
  517. // @section machine
  518. // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
  519. // either in the usual order or reversed
  520. //#define COREXY
  521. //#define COREXZ
  522. //#define COREYZ
  523. //#define COREYX
  524. //#define COREZX
  525. //#define COREZY
  526. //#define MARKFORGED_XY // MarkForged. See https://reprap.org/forum/read.php?152,504042
  527. //===========================================================================
  528. //============================== Endstop Settings ===========================
  529. //===========================================================================
  530. // @section homing
  531. // Specify here all the endstop connectors that are connected to any endstop or probe.
  532. // Almost all printers will be using one per axis. Probes will use one or more of the
  533. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  534. #define USE_XMIN_PLUG
  535. #define USE_YMIN_PLUG
  536. #define USE_ZMIN_PLUG
  537. //#define USE_XMAX_PLUG
  538. //#define USE_YMAX_PLUG
  539. //#define USE_ZMAX_PLUG
  540. // Enable pullup for all endstops to prevent a floating state
  541. #define ENDSTOPPULLUPS
  542. #if DISABLED(ENDSTOPPULLUPS)
  543. // Disable ENDSTOPPULLUPS to set pullups individually
  544. //#define ENDSTOPPULLUP_XMAX
  545. //#define ENDSTOPPULLUP_YMAX
  546. //#define ENDSTOPPULLUP_ZMAX
  547. //#define ENDSTOPPULLUP_XMIN
  548. //#define ENDSTOPPULLUP_YMIN
  549. //#define ENDSTOPPULLUP_ZMIN
  550. //#define ENDSTOPPULLUP_ZMIN_PROBE
  551. #endif
  552. // Enable pulldown for all endstops to prevent a floating state
  553. //#define ENDSTOPPULLDOWNS
  554. #if DISABLED(ENDSTOPPULLDOWNS)
  555. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  556. //#define ENDSTOPPULLDOWN_XMAX
  557. //#define ENDSTOPPULLDOWN_YMAX
  558. //#define ENDSTOPPULLDOWN_ZMAX
  559. //#define ENDSTOPPULLDOWN_XMIN
  560. //#define ENDSTOPPULLDOWN_YMIN
  561. //#define ENDSTOPPULLDOWN_ZMIN
  562. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  563. #endif
  564. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  565. #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  566. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  567. #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  568. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  569. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  570. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  571. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
  572. /**
  573. * Stepper Drivers
  574. *
  575. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  576. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  577. *
  578. * A4988 is assumed for unspecified drivers.
  579. *
  580. * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers.
  581. *
  582. * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
  583. * TB6560, TB6600, TMC2100,
  584. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  585. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  586. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  587. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  588. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  589. */
  590. #define X_DRIVER_TYPE A4988
  591. #define Y_DRIVER_TYPE A4988
  592. #define Z_DRIVER_TYPE A4988
  593. //#define X2_DRIVER_TYPE A4988
  594. //#define Y2_DRIVER_TYPE A4988
  595. //#define Z2_DRIVER_TYPE A4988
  596. //#define Z3_DRIVER_TYPE A4988
  597. //#define Z4_DRIVER_TYPE A4988
  598. #define E0_DRIVER_TYPE A4988
  599. //#define E1_DRIVER_TYPE A4988
  600. //#define E2_DRIVER_TYPE A4988
  601. //#define E3_DRIVER_TYPE A4988
  602. //#define E4_DRIVER_TYPE A4988
  603. //#define E5_DRIVER_TYPE A4988
  604. //#define E6_DRIVER_TYPE A4988
  605. //#define E7_DRIVER_TYPE A4988
  606. // Enable this feature if all enabled endstop pins are interrupt-capable.
  607. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  608. //#define ENDSTOP_INTERRUPTS_FEATURE
  609. /**
  610. * Endstop Noise Threshold
  611. *
  612. * Enable if your probe or endstops falsely trigger due to noise.
  613. *
  614. * - Higher values may affect repeatability or accuracy of some bed probes.
  615. * - To fix noise install a 100nF ceramic capacitor in parallel with the switch.
  616. * - This feature is not required for common micro-switches mounted on PCBs
  617. * based on the Makerbot design, which already have the 100nF capacitor.
  618. *
  619. * :[2,3,4,5,6,7]
  620. */
  621. //#define ENDSTOP_NOISE_THRESHOLD 2
  622. // Check for stuck or disconnected endstops during homing moves.
  623. //#define DETECT_BROKEN_ENDSTOP
  624. //=============================================================================
  625. //============================== Movement Settings ============================
  626. //=============================================================================
  627. // @section motion
  628. /**
  629. * Default Settings
  630. *
  631. * These settings can be reset by M502
  632. *
  633. * Note that if EEPROM is enabled, saved values will override these.
  634. */
  635. /**
  636. * With this option each E stepper can have its own factors for the
  637. * following movement settings. If fewer factors are given than the
  638. * total number of extruders, the last value applies to the rest.
  639. */
  640. //#define DISTINCT_E_FACTORS
  641. /**
  642. * Default Axis Steps Per Unit (steps/mm)
  643. * Override with M92
  644. * X, Y, Z, E0 [, E1[, E2...]]
  645. */
  646. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
  647. /**
  648. * Default Max Feed Rate (mm/s)
  649. * Override with M203
  650. * X, Y, Z, E0 [, E1[, E2...]]
  651. */
  652. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
  653. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  654. #if ENABLED(LIMITED_MAX_FR_EDITING)
  655. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  656. #endif
  657. /**
  658. * Default Max Acceleration (change/s) change = mm/s
  659. * (Maximum start speed for accelerated moves)
  660. * Override with M201
  661. * X, Y, Z, E0 [, E1[, E2...]]
  662. */
  663. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
  664. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  665. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  666. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  667. #endif
  668. /**
  669. * Default Acceleration (change/s) change = mm/s
  670. * Override with M204
  671. *
  672. * M204 P Acceleration
  673. * M204 R Retract Acceleration
  674. * M204 T Travel Acceleration
  675. */
  676. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  677. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  678. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  679. /**
  680. * Default Jerk limits (mm/s)
  681. * Override with M205 X Y Z E
  682. *
  683. * "Jerk" specifies the minimum speed change that requires acceleration.
  684. * When changing speed and direction, if the difference is less than the
  685. * value set here, it may happen instantaneously.
  686. */
  687. //#define CLASSIC_JERK
  688. #if ENABLED(CLASSIC_JERK)
  689. #define DEFAULT_XJERK 10.0
  690. #define DEFAULT_YJERK 10.0
  691. #define DEFAULT_ZJERK 0.3
  692. //#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves
  693. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  694. #if ENABLED(LIMITED_JERK_EDITING)
  695. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  696. #endif
  697. #endif
  698. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  699. /**
  700. * Junction Deviation Factor
  701. *
  702. * See:
  703. * https://reprap.org/forum/read.php?1,739819
  704. * https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  705. */
  706. #if DISABLED(CLASSIC_JERK)
  707. #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
  708. #define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
  709. // for small segments (< 1mm) with large junction angles (> 135°).
  710. #endif
  711. /**
  712. * S-Curve Acceleration
  713. *
  714. * This option eliminates vibration during printing by fitting a Bézier
  715. * curve to move acceleration, producing much smoother direction changes.
  716. *
  717. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  718. */
  719. //#define S_CURVE_ACCELERATION
  720. //===========================================================================
  721. //============================= Z Probe Options =============================
  722. //===========================================================================
  723. // @section probes
  724. //
  725. // See https://marlinfw.org/docs/configuration/probes.html
  726. //
  727. /**
  728. * Enable this option for a probe connected to the Z-MIN pin.
  729. * The probe replaces the Z-MIN endstop and is used for Z homing.
  730. * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  731. */
  732. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  733. // Force the use of the probe for Z-axis homing
  734. //#define USE_PROBE_FOR_Z_HOMING
  735. /**
  736. * Z_MIN_PROBE_PIN
  737. *
  738. * Define this pin if the probe is not connected to Z_MIN_PIN.
  739. * If not defined the default pin for the selected MOTHERBOARD
  740. * will be used. Most of the time the default is what you want.
  741. *
  742. * - The simplest option is to use a free endstop connector.
  743. * - Use 5V for powered (usually inductive) sensors.
  744. *
  745. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  746. * - For simple switches connect...
  747. * - normally-closed switches to GND and D32.
  748. * - normally-open switches to 5V and D32.
  749. */
  750. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  751. /**
  752. * Probe Type
  753. *
  754. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  755. * Activate one of these to use Auto Bed Leveling below.
  756. */
  757. /**
  758. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  759. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  760. * or (with LCD_BED_LEVELING) the LCD controller.
  761. */
  762. //#define PROBE_MANUALLY
  763. //#define MANUAL_PROBE_START_Z 0.2
  764. /**
  765. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  766. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  767. */
  768. //#define FIX_MOUNTED_PROBE
  769. /**
  770. * Use the nozzle as the probe, as with a conductive
  771. * nozzle system or a piezo-electric smart effector.
  772. */
  773. //#define NOZZLE_AS_PROBE
  774. /**
  775. * Z Servo Probe, such as an endstop switch on a rotating arm.
  776. */
  777. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  778. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  779. /**
  780. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  781. */
  782. //#define BLTOUCH
  783. /**
  784. * Touch-MI Probe by hotends.fr
  785. *
  786. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  787. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  788. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  789. *
  790. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  791. * and a minimum Z_HOMING_HEIGHT of 10.
  792. */
  793. //#define TOUCH_MI_PROBE
  794. #if ENABLED(TOUCH_MI_PROBE)
  795. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  796. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  797. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  798. #endif
  799. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  800. //#define SOLENOID_PROBE
  801. // A sled-mounted probe like those designed by Charles Bell.
  802. //#define Z_PROBE_SLED
  803. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  804. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  805. //#define RACK_AND_PINION_PROBE
  806. #if ENABLED(RACK_AND_PINION_PROBE)
  807. #define Z_PROBE_DEPLOY_X X_MIN_POS
  808. #define Z_PROBE_RETRACT_X X_MAX_POS
  809. #endif
  810. // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
  811. // When the pin is defined you can use M672 to set/reset the probe sensivity.
  812. //#define DUET_SMART_EFFECTOR
  813. #if ENABLED(DUET_SMART_EFFECTOR)
  814. #define SMART_EFFECTOR_MOD_PIN -1 // Connect a GPIO pin to the Smart Effector MOD pin
  815. #endif
  816. /**
  817. * Use StallGuard2 to probe the bed with the nozzle.
  818. * Requires stallGuard-capable Trinamic stepper drivers.
  819. * CAUTION: This can damage machines with Z lead screws.
  820. * Take extreme care when setting up this feature.
  821. */
  822. //#define SENSORLESS_PROBING
  823. //
  824. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  825. //
  826. /**
  827. * Nozzle-to-Probe offsets { X, Y, Z }
  828. *
  829. * X and Y offset
  830. * Use a caliper or ruler to measure the distance from the tip of
  831. * the Nozzle to the center-point of the Probe in the X and Y axes.
  832. *
  833. * Z offset
  834. * - For the Z offset use your best known value and adjust at runtime.
  835. * - Common probes trigger below the nozzle and have negative values for Z offset.
  836. * - Probes triggering above the nozzle height are uncommon but do exist. When using
  837. * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES
  838. * to avoid collisions during probing.
  839. *
  840. * Tune and Adjust
  841. * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc.
  842. * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset.
  843. *
  844. * Assuming the typical work area orientation:
  845. * - Probe to RIGHT of the Nozzle has a Positive X offset
  846. * - Probe to LEFT of the Nozzle has a Negative X offset
  847. * - Probe in BACK of the Nozzle has a Positive Y offset
  848. * - Probe in FRONT of the Nozzle has a Negative Y offset
  849. *
  850. * Some examples:
  851. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, -1 } // Example "1"
  852. * #define NOZZLE_TO_PROBE_OFFSET {-10, 5, -1 } // Example "2"
  853. * #define NOZZLE_TO_PROBE_OFFSET { 5, -5, -1 } // Example "3"
  854. * #define NOZZLE_TO_PROBE_OFFSET {-15,-10, -1 } // Example "4"
  855. *
  856. * +-- BACK ---+
  857. * | [+] |
  858. * L | 1 | R <-- Example "1" (right+, back+)
  859. * E | 2 | I <-- Example "2" ( left-, back+)
  860. * F |[-] N [+]| G <-- Nozzle
  861. * T | 3 | H <-- Example "3" (right+, front-)
  862. * | 4 | T <-- Example "4" ( left-, front-)
  863. * | [-] |
  864. * O-- FRONT --+
  865. */
  866. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  867. // Most probes should stay away from the edges of the bed, but
  868. // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
  869. #define PROBING_MARGIN 10
  870. // X and Y axis travel speed (mm/min) between probes
  871. #define XY_PROBE_SPEED (133*60)
  872. // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  873. #define Z_PROBE_SPEED_FAST (4*60)
  874. // Feedrate (mm/min) for the "accurate" probe of each point
  875. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  876. /**
  877. * Probe Activation Switch
  878. * A switch indicating proper deployment, or an optical
  879. * switch triggered when the carriage is near the bed.
  880. */
  881. //#define PROBE_ACTIVATION_SWITCH
  882. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  883. #define PROBE_ACTIVATION_SWITCH_STATE LOW // State indicating probe is active
  884. //#define PROBE_ACTIVATION_SWITCH_PIN PC6 // Override default pin
  885. #endif
  886. /**
  887. * Tare Probe (determine zero-point) prior to each probe.
  888. * Useful for a strain gauge or piezo sensor that needs to factor out
  889. * elements such as cables pulling on the carriage.
  890. */
  891. //#define PROBE_TARE
  892. #if ENABLED(PROBE_TARE)
  893. #define PROBE_TARE_TIME 200 // (ms) Time to hold tare pin
  894. #define PROBE_TARE_DELAY 200 // (ms) Delay after tare before
  895. #define PROBE_TARE_STATE HIGH // State to write pin for tare
  896. //#define PROBE_TARE_PIN PA5 // Override default pin
  897. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  898. //#define PROBE_TARE_ONLY_WHILE_INACTIVE // Fail to tare/probe if PROBE_ACTIVATION_SWITCH is active
  899. #endif
  900. #endif
  901. /**
  902. * Multiple Probing
  903. *
  904. * You may get improved results by probing 2 or more times.
  905. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  906. *
  907. * A total of 2 does fast/slow probes with a weighted average.
  908. * A total of 3 or more adds more slow probes, taking the average.
  909. */
  910. //#define MULTIPLE_PROBING 2
  911. //#define EXTRA_PROBING 1
  912. /**
  913. * Z probes require clearance when deploying, stowing, and moving between
  914. * probe points to avoid hitting the bed and other hardware.
  915. * Servo-mounted probes require extra space for the arm to rotate.
  916. * Inductive probes need space to keep from triggering early.
  917. *
  918. * Use these settings to specify the distance (mm) to raise the probe (or
  919. * lower the bed). The values set here apply over and above any (negative)
  920. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  921. * Only integer values >= 1 are valid here.
  922. *
  923. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  924. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  925. */
  926. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  927. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  928. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  929. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  930. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  931. // For M851 give a range for adjusting the Z probe offset
  932. #define Z_PROBE_OFFSET_RANGE_MIN -20
  933. #define Z_PROBE_OFFSET_RANGE_MAX 20
  934. // Enable the M48 repeatability test to test probe accuracy
  935. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  936. // Before deploy/stow pause for user confirmation
  937. //#define PAUSE_BEFORE_DEPLOY_STOW
  938. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  939. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  940. #endif
  941. /**
  942. * Enable one or more of the following if probing seems unreliable.
  943. * Heaters and/or fans can be disabled during probing to minimize electrical
  944. * noise. A delay can also be added to allow noise and vibration to settle.
  945. * These options are most useful for the BLTouch probe, but may also improve
  946. * readings with inductive probes and piezo sensors.
  947. */
  948. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  949. #if ENABLED(PROBING_HEATERS_OFF)
  950. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  951. #endif
  952. //#define PROBING_FANS_OFF // Turn fans off when probing
  953. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  954. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  955. // Require minimum nozzle and/or bed temperature for probing
  956. //#define PREHEAT_BEFORE_PROBING
  957. #if ENABLED(PREHEAT_BEFORE_PROBING)
  958. #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  959. #define PROBING_BED_TEMP 50
  960. #endif
  961. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  962. // :{ 0:'Low', 1:'High' }
  963. #define X_ENABLE_ON 0
  964. #define Y_ENABLE_ON 0
  965. #define Z_ENABLE_ON 0
  966. #define E_ENABLE_ON 0 // For all extruders
  967. // Disable axis steppers immediately when they're not being stepped.
  968. // WARNING: When motors turn off there is a chance of losing position accuracy!
  969. #define DISABLE_X false
  970. #define DISABLE_Y false
  971. #define DISABLE_Z false
  972. // Turn off the display blinking that warns about possible accuracy reduction
  973. //#define DISABLE_REDUCED_ACCURACY_WARNING
  974. // @section extruder
  975. #define DISABLE_E false // Disable the extruder when not stepping
  976. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  977. // @section machine
  978. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  979. #define INVERT_X_DIR false
  980. #define INVERT_Y_DIR true
  981. #define INVERT_Z_DIR false
  982. // @section extruder
  983. // For direct drive extruder v9 set to true, for geared extruder set to false.
  984. #define INVERT_E0_DIR false
  985. #define INVERT_E1_DIR false
  986. #define INVERT_E2_DIR false
  987. #define INVERT_E3_DIR false
  988. #define INVERT_E4_DIR false
  989. #define INVERT_E5_DIR false
  990. #define INVERT_E6_DIR false
  991. #define INVERT_E7_DIR false
  992. // @section homing
  993. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety.
  994. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
  995. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  996. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  997. // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
  998. //#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
  999. // Direction of endstops when homing; 1=MAX, -1=MIN
  1000. // :[-1,1]
  1001. #define X_HOME_DIR -1
  1002. #define Y_HOME_DIR -1
  1003. #define Z_HOME_DIR -1
  1004. // @section machine
  1005. // The size of the print bed
  1006. #define X_BED_SIZE 200
  1007. #define Y_BED_SIZE 200
  1008. // Travel limits (mm) after homing, corresponding to endstop positions.
  1009. #define X_MIN_POS 0
  1010. #define Y_MIN_POS 0
  1011. #define Z_MIN_POS 0
  1012. #define X_MAX_POS X_BED_SIZE
  1013. #define Y_MAX_POS Y_BED_SIZE
  1014. #define Z_MAX_POS 200
  1015. /**
  1016. * Software Endstops
  1017. *
  1018. * - Prevent moves outside the set machine bounds.
  1019. * - Individual axes can be disabled, if desired.
  1020. * - X and Y only apply to Cartesian robots.
  1021. * - Use 'M211' to set software endstops on/off or report current state
  1022. */
  1023. // Min software endstops constrain movement within minimum coordinate bounds
  1024. #define MIN_SOFTWARE_ENDSTOPS
  1025. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  1026. #define MIN_SOFTWARE_ENDSTOP_X
  1027. #define MIN_SOFTWARE_ENDSTOP_Y
  1028. #define MIN_SOFTWARE_ENDSTOP_Z
  1029. #endif
  1030. // Max software endstops constrain movement within maximum coordinate bounds
  1031. #define MAX_SOFTWARE_ENDSTOPS
  1032. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  1033. #define MAX_SOFTWARE_ENDSTOP_X
  1034. #define MAX_SOFTWARE_ENDSTOP_Y
  1035. #define MAX_SOFTWARE_ENDSTOP_Z
  1036. #endif
  1037. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  1038. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  1039. #endif
  1040. /**
  1041. * Filament Runout Sensors
  1042. * Mechanical or opto endstops are used to check for the presence of filament.
  1043. *
  1044. * IMPORTANT: Runout will only trigger if Marlin is aware that a print job is running.
  1045. * Marlin knows a print job is running when:
  1046. * 1. Running a print job from media started with M24.
  1047. * 2. The Print Job Timer has been started with M75.
  1048. * 3. The heaters were turned on and PRINTJOB_TIMER_AUTOSTART is enabled.
  1049. *
  1050. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  1051. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  1052. */
  1053. //#define FILAMENT_RUNOUT_SENSOR
  1054. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  1055. #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
  1056. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  1057. #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
  1058. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  1059. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  1060. // Override individually if the runout sensors vary
  1061. //#define FIL_RUNOUT1_STATE LOW
  1062. //#define FIL_RUNOUT1_PULLUP
  1063. //#define FIL_RUNOUT1_PULLDOWN
  1064. //#define FIL_RUNOUT2_STATE LOW
  1065. //#define FIL_RUNOUT2_PULLUP
  1066. //#define FIL_RUNOUT2_PULLDOWN
  1067. //#define FIL_RUNOUT3_STATE LOW
  1068. //#define FIL_RUNOUT3_PULLUP
  1069. //#define FIL_RUNOUT3_PULLDOWN
  1070. //#define FIL_RUNOUT4_STATE LOW
  1071. //#define FIL_RUNOUT4_PULLUP
  1072. //#define FIL_RUNOUT4_PULLDOWN
  1073. //#define FIL_RUNOUT5_STATE LOW
  1074. //#define FIL_RUNOUT5_PULLUP
  1075. //#define FIL_RUNOUT5_PULLDOWN
  1076. //#define FIL_RUNOUT6_STATE LOW
  1077. //#define FIL_RUNOUT6_PULLUP
  1078. //#define FIL_RUNOUT6_PULLDOWN
  1079. //#define FIL_RUNOUT7_STATE LOW
  1080. //#define FIL_RUNOUT7_PULLUP
  1081. //#define FIL_RUNOUT7_PULLDOWN
  1082. //#define FIL_RUNOUT8_STATE LOW
  1083. //#define FIL_RUNOUT8_PULLUP
  1084. //#define FIL_RUNOUT8_PULLDOWN
  1085. // Set one or more commands to execute on filament runout.
  1086. // (After 'M412 H' Marlin will ask the host to handle the process.)
  1087. #define FILAMENT_RUNOUT_SCRIPT "M600"
  1088. // After a runout is detected, continue printing this length of filament
  1089. // before executing the runout script. Useful for a sensor at the end of
  1090. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  1091. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  1092. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  1093. // Enable this option to use an encoder disc that toggles the runout pin
  1094. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  1095. // large enough to avoid false positives.)
  1096. //#define FILAMENT_MOTION_SENSOR
  1097. #endif
  1098. #endif
  1099. //===========================================================================
  1100. //=============================== Bed Leveling ==============================
  1101. //===========================================================================
  1102. // @section calibrate
  1103. /**
  1104. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  1105. * and behavior of G29 will change depending on your selection.
  1106. *
  1107. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  1108. *
  1109. * - AUTO_BED_LEVELING_3POINT
  1110. * Probe 3 arbitrary points on the bed (that aren't collinear)
  1111. * You specify the XY coordinates of all 3 points.
  1112. * The result is a single tilted plane. Best for a flat bed.
  1113. *
  1114. * - AUTO_BED_LEVELING_LINEAR
  1115. * Probe several points in a grid.
  1116. * You specify the rectangle and the density of sample points.
  1117. * The result is a single tilted plane. Best for a flat bed.
  1118. *
  1119. * - AUTO_BED_LEVELING_BILINEAR
  1120. * Probe several points in a grid.
  1121. * You specify the rectangle and the density of sample points.
  1122. * The result is a mesh, best for large or uneven beds.
  1123. *
  1124. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1125. * A comprehensive bed leveling system combining the features and benefits
  1126. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1127. * Validation and Mesh Editing systems.
  1128. *
  1129. * - MESH_BED_LEVELING
  1130. * Probe a grid manually
  1131. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1132. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1133. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1134. * With an LCD controller the process is guided step-by-step.
  1135. */
  1136. //#define AUTO_BED_LEVELING_3POINT
  1137. //#define AUTO_BED_LEVELING_LINEAR
  1138. //#define AUTO_BED_LEVELING_BILINEAR
  1139. //#define AUTO_BED_LEVELING_UBL
  1140. //#define MESH_BED_LEVELING
  1141. /**
  1142. * Normally G28 leaves leveling disabled on completion. Enable one of
  1143. * these options to restore the prior leveling state or to always enable
  1144. * leveling immediately after G28.
  1145. */
  1146. //#define RESTORE_LEVELING_AFTER_G28
  1147. //#define ENABLE_LEVELING_AFTER_G28
  1148. /**
  1149. * Auto-leveling needs preheating
  1150. */
  1151. //#define PREHEAT_BEFORE_LEVELING
  1152. #if ENABLED(PREHEAT_BEFORE_LEVELING)
  1153. #define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  1154. #define LEVELING_BED_TEMP 50
  1155. #endif
  1156. /**
  1157. * Enable detailed logging of G28, G29, M48, etc.
  1158. * Turn on with the command 'M111 S32'.
  1159. * NOTE: Requires a lot of PROGMEM!
  1160. */
  1161. //#define DEBUG_LEVELING_FEATURE
  1162. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1163. // Gradually reduce leveling correction until a set height is reached,
  1164. // at which point movement will be level to the machine's XY plane.
  1165. // The height can be set with M420 Z<height>
  1166. #define ENABLE_LEVELING_FADE_HEIGHT
  1167. #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
  1168. #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
  1169. #endif
  1170. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1171. // split up moves into short segments like a Delta. This follows the
  1172. // contours of the bed more closely than edge-to-edge straight moves.
  1173. #define SEGMENT_LEVELED_MOVES
  1174. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1175. /**
  1176. * Enable the G26 Mesh Validation Pattern tool.
  1177. */
  1178. //#define G26_MESH_VALIDATION
  1179. #if ENABLED(G26_MESH_VALIDATION)
  1180. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1181. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
  1182. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for G26.
  1183. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for G26.
  1184. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for G26 XY moves.
  1185. #define G26_XY_FEEDRATE_TRAVEL 100 // (mm/s) Feedrate for G26 XY travel moves.
  1186. #define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements.
  1187. #endif
  1188. #endif
  1189. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1190. // Set the number of grid points per dimension.
  1191. #define GRID_MAX_POINTS_X 3
  1192. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1193. // Probe along the Y axis, advancing X after each column
  1194. //#define PROBE_Y_FIRST
  1195. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1196. // Beyond the probed grid, continue the implied tilt?
  1197. // Default is to maintain the height of the nearest edge.
  1198. //#define EXTRAPOLATE_BEYOND_GRID
  1199. //
  1200. // Experimental Subdivision of the grid by Catmull-Rom method.
  1201. // Synthesizes intermediate points to produce a more detailed mesh.
  1202. //
  1203. //#define ABL_BILINEAR_SUBDIVISION
  1204. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1205. // Number of subdivisions between probe points
  1206. #define BILINEAR_SUBDIVISIONS 3
  1207. #endif
  1208. #endif
  1209. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1210. //===========================================================================
  1211. //========================= Unified Bed Leveling ============================
  1212. //===========================================================================
  1213. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1214. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1215. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1216. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1217. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1218. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1219. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1220. // as the Z-Height correction value.
  1221. #elif ENABLED(MESH_BED_LEVELING)
  1222. //===========================================================================
  1223. //=================================== Mesh ==================================
  1224. //===========================================================================
  1225. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1226. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1227. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1228. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1229. #endif // BED_LEVELING
  1230. /**
  1231. * Add a bed leveling sub-menu for ABL or MBL.
  1232. * Include a guided procedure if manual probing is enabled.
  1233. */
  1234. //#define LCD_BED_LEVELING
  1235. #if ENABLED(LCD_BED_LEVELING)
  1236. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1237. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1238. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1239. #endif
  1240. // Add a menu item to move between bed corners for manual bed adjustment
  1241. //#define LEVEL_BED_CORNERS
  1242. #if ENABLED(LEVEL_BED_CORNERS)
  1243. #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
  1244. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1245. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points
  1246. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1247. //#define LEVEL_CORNERS_USE_PROBE
  1248. #if ENABLED(LEVEL_CORNERS_USE_PROBE)
  1249. #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
  1250. #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
  1251. //#define LEVEL_CORNERS_AUDIO_FEEDBACK
  1252. #endif
  1253. /**
  1254. * Corner Leveling Order
  1255. *
  1256. * Set 2 or 4 points. When 2 points are given, the 3rd is the center of the opposite edge.
  1257. *
  1258. * LF Left-Front RF Right-Front
  1259. * LB Left-Back RB Right-Back
  1260. *
  1261. * Examples:
  1262. *
  1263. * Default {LF,RB,LB,RF} {LF,RF} {LB,LF}
  1264. * LB --------- RB LB --------- RB LB --------- RB LB --------- RB
  1265. * | 4 3 | | 3 2 | | <3> | | 1 |
  1266. * | | | | | | | <3>|
  1267. * | 1 2 | | 1 4 | | 1 2 | | 2 |
  1268. * LF --------- RF LF --------- RF LF --------- RF LF --------- RF
  1269. */
  1270. #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB }
  1271. #endif
  1272. /**
  1273. * Commands to execute at the end of G29 probing.
  1274. * Useful to retract or move the Z probe out of the way.
  1275. */
  1276. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1277. // @section homing
  1278. // The center of the bed is at (X=0, Y=0)
  1279. //#define BED_CENTER_AT_0_0
  1280. // Manually set the home position. Leave these undefined for automatic settings.
  1281. // For DELTA this is the top-center of the Cartesian print volume.
  1282. //#define MANUAL_X_HOME_POS 0
  1283. //#define MANUAL_Y_HOME_POS 0
  1284. //#define MANUAL_Z_HOME_POS 0
  1285. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1286. //
  1287. // With this feature enabled:
  1288. //
  1289. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1290. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1291. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing.
  1292. // - Prevent Z homing when the Z probe is outside bed area.
  1293. //
  1294. //#define Z_SAFE_HOMING
  1295. #if ENABLED(Z_SAFE_HOMING)
  1296. #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
  1297. #define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing
  1298. #endif
  1299. // Homing speeds (mm/min)
  1300. #define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
  1301. // Validate that endstops are triggered on homing moves
  1302. #define VALIDATE_HOMING_ENDSTOPS
  1303. // @section calibrate
  1304. /**
  1305. * Bed Skew Compensation
  1306. *
  1307. * This feature corrects for misalignment in the XYZ axes.
  1308. *
  1309. * Take the following steps to get the bed skew in the XY plane:
  1310. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1311. * 2. For XY_DIAG_AC measure the diagonal A to C
  1312. * 3. For XY_DIAG_BD measure the diagonal B to D
  1313. * 4. For XY_SIDE_AD measure the edge A to D
  1314. *
  1315. * Marlin automatically computes skew factors from these measurements.
  1316. * Skew factors may also be computed and set manually:
  1317. *
  1318. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1319. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1320. *
  1321. * If desired, follow the same procedure for XZ and YZ.
  1322. * Use these diagrams for reference:
  1323. *
  1324. * Y Z Z
  1325. * ^ B-------C ^ B-------C ^ B-------C
  1326. * | / / | / / | / /
  1327. * | / / | / / | / /
  1328. * | A-------D | A-------D | A-------D
  1329. * +-------------->X +-------------->X +-------------->Y
  1330. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1331. */
  1332. //#define SKEW_CORRECTION
  1333. #if ENABLED(SKEW_CORRECTION)
  1334. // Input all length measurements here:
  1335. #define XY_DIAG_AC 282.8427124746
  1336. #define XY_DIAG_BD 282.8427124746
  1337. #define XY_SIDE_AD 200
  1338. // Or, set the default skew factors directly here
  1339. // to override the above measurements:
  1340. #define XY_SKEW_FACTOR 0.0
  1341. //#define SKEW_CORRECTION_FOR_Z
  1342. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1343. #define XZ_DIAG_AC 282.8427124746
  1344. #define XZ_DIAG_BD 282.8427124746
  1345. #define YZ_DIAG_AC 282.8427124746
  1346. #define YZ_DIAG_BD 282.8427124746
  1347. #define YZ_SIDE_AD 200
  1348. #define XZ_SKEW_FACTOR 0.0
  1349. #define YZ_SKEW_FACTOR 0.0
  1350. #endif
  1351. // Enable this option for M852 to set skew at runtime
  1352. //#define SKEW_CORRECTION_GCODE
  1353. #endif
  1354. //=============================================================================
  1355. //============================= Additional Features ===========================
  1356. //=============================================================================
  1357. // @section extras
  1358. /**
  1359. * EEPROM
  1360. *
  1361. * Persistent storage to preserve configurable settings across reboots.
  1362. *
  1363. * M500 - Store settings to EEPROM.
  1364. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1365. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1366. */
  1367. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1368. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1369. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1370. #define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
  1371. #if ENABLED(EEPROM_SETTINGS)
  1372. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1373. #endif
  1374. //
  1375. // Host Keepalive
  1376. //
  1377. // When enabled Marlin will send a busy status message to the host
  1378. // every couple of seconds when it can't accept commands.
  1379. //
  1380. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1381. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1382. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1383. //
  1384. // G20/G21 Inch mode support
  1385. //
  1386. //#define INCH_MODE_SUPPORT
  1387. //
  1388. // M149 Set temperature units support
  1389. //
  1390. //#define TEMPERATURE_UNITS_SUPPORT
  1391. // @section temperature
  1392. // Preheat Constants
  1393. #define PREHEAT_1_LABEL "PLA"
  1394. #define PREHEAT_1_TEMP_HOTEND 180
  1395. #define PREHEAT_1_TEMP_BED 70
  1396. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1397. #define PREHEAT_2_LABEL "ABS"
  1398. #define PREHEAT_2_TEMP_HOTEND 240
  1399. #define PREHEAT_2_TEMP_BED 110
  1400. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1401. /**
  1402. * Nozzle Park
  1403. *
  1404. * Park the nozzle at the given XYZ position on idle or G27.
  1405. *
  1406. * The "P" parameter controls the action applied to the Z axis:
  1407. *
  1408. * P0 (Default) If Z is below park Z raise the nozzle.
  1409. * P1 Raise the nozzle always to Z-park height.
  1410. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1411. */
  1412. //#define NOZZLE_PARK_FEATURE
  1413. #if ENABLED(NOZZLE_PARK_FEATURE)
  1414. // Specify a park position as { X, Y, Z_raise }
  1415. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1416. //#define NOZZLE_PARK_X_ONLY // X move only is required to park
  1417. //#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
  1418. #define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
  1419. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1420. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1421. #endif
  1422. /**
  1423. * Clean Nozzle Feature -- EXPERIMENTAL
  1424. *
  1425. * Adds the G12 command to perform a nozzle cleaning process.
  1426. *
  1427. * Parameters:
  1428. * P Pattern
  1429. * S Strokes / Repetitions
  1430. * T Triangles (P1 only)
  1431. *
  1432. * Patterns:
  1433. * P0 Straight line (default). This process requires a sponge type material
  1434. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1435. * between the start / end points.
  1436. *
  1437. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1438. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1439. * Zig-zags are done in whichever is the narrower dimension.
  1440. * For example, "G12 P1 S1 T3" will execute:
  1441. *
  1442. * --
  1443. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1444. * | | / \ / \ / \ |
  1445. * A | | / \ / \ / \ |
  1446. * | | / \ / \ / \ |
  1447. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1448. * -- +--------------------------------+
  1449. * |________|_________|_________|
  1450. * T1 T2 T3
  1451. *
  1452. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1453. * "R" specifies the radius. "S" specifies the stroke count.
  1454. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1455. *
  1456. * Caveats: The ending Z should be the same as starting Z.
  1457. * Attention: EXPERIMENTAL. G-code arguments may change.
  1458. */
  1459. //#define NOZZLE_CLEAN_FEATURE
  1460. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1461. // Default number of pattern repetitions
  1462. #define NOZZLE_CLEAN_STROKES 12
  1463. // Default number of triangles
  1464. #define NOZZLE_CLEAN_TRIANGLES 3
  1465. // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
  1466. // Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
  1467. #define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } }
  1468. #define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } }
  1469. // Circular pattern radius
  1470. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1471. // Circular pattern circle fragments number
  1472. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1473. // Middle point of circle
  1474. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1475. // Move the nozzle to the initial position after cleaning
  1476. #define NOZZLE_CLEAN_GOBACK
  1477. // For a purge/clean station that's always at the gantry height (thus no Z move)
  1478. //#define NOZZLE_CLEAN_NO_Z
  1479. // For a purge/clean station mounted on the X axis
  1480. //#define NOZZLE_CLEAN_NO_Y
  1481. // Require a minimum hotend temperature for cleaning
  1482. #define NOZZLE_CLEAN_MIN_TEMP 170
  1483. //#define NOZZLE_CLEAN_HEATUP // Heat up the nozzle instead of skipping wipe
  1484. // Explicit wipe G-code script applies to a G12 with no arguments.
  1485. //#define WIPE_SEQUENCE_COMMANDS "G1 X-17 Y25 Z10 F4000\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X-10.0 Y-9.0"
  1486. #endif
  1487. /**
  1488. * Print Job Timer
  1489. *
  1490. * Automatically start and stop the print job timer on M104/M109/M190.
  1491. *
  1492. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1493. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1494. * M190 (bed, wait) - high temp = start timer, low temp = none
  1495. *
  1496. * The timer can also be controlled with the following commands:
  1497. *
  1498. * M75 - Start the print job timer
  1499. * M76 - Pause the print job timer
  1500. * M77 - Stop the print job timer
  1501. */
  1502. #define PRINTJOB_TIMER_AUTOSTART
  1503. /**
  1504. * Print Counter
  1505. *
  1506. * Track statistical data such as:
  1507. *
  1508. * - Total print jobs
  1509. * - Total successful print jobs
  1510. * - Total failed print jobs
  1511. * - Total time printing
  1512. *
  1513. * View the current statistics with M78.
  1514. */
  1515. //#define PRINTCOUNTER
  1516. #if ENABLED(PRINTCOUNTER)
  1517. #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print
  1518. #endif
  1519. /**
  1520. * Password
  1521. *
  1522. * Set a numerical password for the printer which can be requested:
  1523. *
  1524. * - When the printer boots up
  1525. * - Upon opening the 'Print from Media' Menu
  1526. * - When SD printing is completed or aborted
  1527. *
  1528. * The following G-codes can be used:
  1529. *
  1530. * M510 - Lock Printer. Blocks all commands except M511.
  1531. * M511 - Unlock Printer.
  1532. * M512 - Set, Change and Remove Password.
  1533. *
  1534. * If you forget the password and get locked out you'll need to re-flash
  1535. * the firmware with the feature disabled, reset EEPROM, and (optionally)
  1536. * re-flash the firmware again with this feature enabled.
  1537. */
  1538. //#define PASSWORD_FEATURE
  1539. #if ENABLED(PASSWORD_FEATURE)
  1540. #define PASSWORD_LENGTH 4 // (#) Number of digits (1-9). 3 or 4 is recommended
  1541. #define PASSWORD_ON_STARTUP
  1542. #define PASSWORD_UNLOCK_GCODE // Unlock with the M511 P<password> command. Disable to prevent brute-force attack.
  1543. #define PASSWORD_CHANGE_GCODE // Change the password with M512 P<old> S<new>.
  1544. //#define PASSWORD_ON_SD_PRINT_MENU // This does not prevent gcodes from running
  1545. //#define PASSWORD_AFTER_SD_PRINT_END
  1546. //#define PASSWORD_AFTER_SD_PRINT_ABORT
  1547. //#include "Configuration_Secure.h" // External file with PASSWORD_DEFAULT_VALUE
  1548. #endif
  1549. //=============================================================================
  1550. //============================= LCD and SD support ============================
  1551. //=============================================================================
  1552. // @section lcd
  1553. /**
  1554. * LCD LANGUAGE
  1555. *
  1556. * Select the language to display on the LCD. These languages are available:
  1557. *
  1558. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, hu, it,
  1559. * jp_kana, ko_KR, nl, pl, pt, pt_br, ro, ru, sk, sv, tr, uk, vi, zh_CN, zh_TW
  1560. *
  1561. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'hu':'Hungarian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ro':'Romanian', 'ru':'Russian', 'sk':'Slovak', 'sv':'Swedish', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)' }
  1562. */
  1563. #define LCD_LANGUAGE en
  1564. /**
  1565. * LCD Character Set
  1566. *
  1567. * Note: This option is NOT applicable to Graphical Displays.
  1568. *
  1569. * All character-based LCDs provide ASCII plus one of these
  1570. * language extensions:
  1571. *
  1572. * - JAPANESE ... the most common
  1573. * - WESTERN ... with more accented characters
  1574. * - CYRILLIC ... for the Russian language
  1575. *
  1576. * To determine the language extension installed on your controller:
  1577. *
  1578. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1579. * - Click the controller to view the LCD menu
  1580. * - The LCD will display Japanese, Western, or Cyrillic text
  1581. *
  1582. * See https://marlinfw.org/docs/development/lcd_language.html
  1583. *
  1584. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1585. */
  1586. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1587. /**
  1588. * Info Screen Style (0:Classic, 1:Průša)
  1589. *
  1590. * :[0:'Classic', 1:'Průša']
  1591. */
  1592. #define LCD_INFO_SCREEN_STYLE 0
  1593. /**
  1594. * SD CARD
  1595. *
  1596. * SD Card support is disabled by default. If your controller has an SD slot,
  1597. * you must uncomment the following option or it won't work.
  1598. */
  1599. //#define SDSUPPORT
  1600. /**
  1601. * SD CARD: ENABLE CRC
  1602. *
  1603. * Use CRC checks and retries on the SD communication.
  1604. */
  1605. //#define SD_CHECK_AND_RETRY
  1606. /**
  1607. * LCD Menu Items
  1608. *
  1609. * Disable all menus and only display the Status Screen, or
  1610. * just remove some extraneous menu items to recover space.
  1611. */
  1612. //#define NO_LCD_MENUS
  1613. //#define SLIM_LCD_MENUS
  1614. //
  1615. // ENCODER SETTINGS
  1616. //
  1617. // This option overrides the default number of encoder pulses needed to
  1618. // produce one step. Should be increased for high-resolution encoders.
  1619. //
  1620. //#define ENCODER_PULSES_PER_STEP 4
  1621. //
  1622. // Use this option to override the number of step signals required to
  1623. // move between next/prev menu items.
  1624. //
  1625. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1626. /**
  1627. * Encoder Direction Options
  1628. *
  1629. * Test your encoder's behavior first with both options disabled.
  1630. *
  1631. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1632. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1633. * Reversed Value Editing only? Enable BOTH options.
  1634. */
  1635. //
  1636. // This option reverses the encoder direction everywhere.
  1637. //
  1638. // Set this option if CLOCKWISE causes values to DECREASE
  1639. //
  1640. //#define REVERSE_ENCODER_DIRECTION
  1641. //
  1642. // This option reverses the encoder direction for navigating LCD menus.
  1643. //
  1644. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1645. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1646. //
  1647. //#define REVERSE_MENU_DIRECTION
  1648. //
  1649. // This option reverses the encoder direction for Select Screen.
  1650. //
  1651. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1652. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1653. //
  1654. //#define REVERSE_SELECT_DIRECTION
  1655. //
  1656. // Individual Axis Homing
  1657. //
  1658. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1659. //
  1660. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1661. //
  1662. // SPEAKER/BUZZER
  1663. //
  1664. // If you have a speaker that can produce tones, enable it here.
  1665. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1666. //
  1667. //#define SPEAKER
  1668. //
  1669. // The duration and frequency for the UI feedback sound.
  1670. // Set these to 0 to disable audio feedback in the LCD menus.
  1671. //
  1672. // Note: Test audio output with the G-Code:
  1673. // M300 S<frequency Hz> P<duration ms>
  1674. //
  1675. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1676. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1677. //=============================================================================
  1678. //======================== LCD / Controller Selection =========================
  1679. //======================== (Character-based LCDs) =========================
  1680. //=============================================================================
  1681. //
  1682. // RepRapDiscount Smart Controller.
  1683. // https://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1684. //
  1685. // Note: Usually sold with a white PCB.
  1686. //
  1687. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1688. //
  1689. // Original RADDS LCD Display+Encoder+SDCardReader
  1690. // http://doku.radds.org/dokumentation/lcd-display/
  1691. //
  1692. //#define RADDS_DISPLAY
  1693. //
  1694. // ULTIMAKER Controller.
  1695. //
  1696. //#define ULTIMAKERCONTROLLER
  1697. //
  1698. // ULTIPANEL as seen on Thingiverse.
  1699. //
  1700. //#define ULTIPANEL
  1701. //
  1702. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1703. // https://reprap.org/wiki/PanelOne
  1704. //
  1705. //#define PANEL_ONE
  1706. //
  1707. // GADGETS3D G3D LCD/SD Controller
  1708. // https://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1709. //
  1710. // Note: Usually sold with a blue PCB.
  1711. //
  1712. //#define G3D_PANEL
  1713. //
  1714. // RigidBot Panel V1.0
  1715. // http://www.inventapart.com/
  1716. //
  1717. //#define RIGIDBOT_PANEL
  1718. //
  1719. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1720. // https://www.aliexpress.com/item/32765887917.html
  1721. //
  1722. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1723. //
  1724. // ANET and Tronxy 20x4 Controller
  1725. //
  1726. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1727. // This LCD is known to be susceptible to electrical interference
  1728. // which scrambles the display. Pressing any button clears it up.
  1729. // This is a LCD2004 display with 5 analog buttons.
  1730. //
  1731. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1732. //
  1733. //#define ULTRA_LCD
  1734. //=============================================================================
  1735. //======================== LCD / Controller Selection =========================
  1736. //===================== (I2C and Shift-Register LCDs) =====================
  1737. //=============================================================================
  1738. //
  1739. // CONTROLLER TYPE: I2C
  1740. //
  1741. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1742. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1743. //
  1744. //
  1745. // Elefu RA Board Control Panel
  1746. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1747. //
  1748. //#define RA_CONTROL_PANEL
  1749. //
  1750. // Sainsmart (YwRobot) LCD Displays
  1751. //
  1752. // These require F.Malpartida's LiquidCrystal_I2C library
  1753. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1754. //
  1755. //#define LCD_SAINSMART_I2C_1602
  1756. //#define LCD_SAINSMART_I2C_2004
  1757. //
  1758. // Generic LCM1602 LCD adapter
  1759. //
  1760. //#define LCM1602
  1761. //
  1762. // PANELOLU2 LCD with status LEDs,
  1763. // separate encoder and click inputs.
  1764. //
  1765. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1766. // For more info: https://github.com/lincomatic/LiquidTWI2
  1767. //
  1768. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1769. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1770. //
  1771. //#define LCD_I2C_PANELOLU2
  1772. //
  1773. // Panucatt VIKI LCD with status LEDs,
  1774. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1775. //
  1776. //#define LCD_I2C_VIKI
  1777. //
  1778. // CONTROLLER TYPE: Shift register panels
  1779. //
  1780. //
  1781. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1782. // LCD configuration: https://reprap.org/wiki/SAV_3D_LCD
  1783. //
  1784. //#define SAV_3DLCD
  1785. //
  1786. // 3-wire SR LCD with strobe using 74HC4094
  1787. // https://github.com/mikeshub/SailfishLCD
  1788. // Uses the code directly from Sailfish
  1789. //
  1790. //#define FF_INTERFACEBOARD
  1791. //
  1792. // TFT GLCD Panel with Marlin UI
  1793. // Panel connected to main board by SPI or I2C interface.
  1794. // See https://github.com/Serhiy-K/TFTGLCDAdapter
  1795. //
  1796. //#define TFTGLCD_PANEL_SPI
  1797. //#define TFTGLCD_PANEL_I2C
  1798. //=============================================================================
  1799. //======================= LCD / Controller Selection =======================
  1800. //========================= (Graphical LCDs) ========================
  1801. //=============================================================================
  1802. //
  1803. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1804. //
  1805. // IMPORTANT: The U8glib library is required for Graphical Display!
  1806. // https://github.com/olikraus/U8glib_Arduino
  1807. //
  1808. // NOTE: If the LCD is unresponsive you may need to reverse the plugs.
  1809. //
  1810. //
  1811. // RepRapDiscount FULL GRAPHIC Smart Controller
  1812. // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1813. //
  1814. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1815. //
  1816. // ReprapWorld Graphical LCD
  1817. // https://reprapworld.com/?products_details&products_id/1218
  1818. //
  1819. //#define REPRAPWORLD_GRAPHICAL_LCD
  1820. //
  1821. // Activate one of these if you have a Panucatt Devices
  1822. // Viki 2.0 or mini Viki with Graphic LCD
  1823. // https://www.panucatt.com
  1824. //
  1825. //#define VIKI2
  1826. //#define miniVIKI
  1827. //
  1828. // MakerLab Mini Panel with graphic
  1829. // controller and SD support - https://reprap.org/wiki/Mini_panel
  1830. //
  1831. //#define MINIPANEL
  1832. //
  1833. // MaKr3d Makr-Panel with graphic controller and SD support.
  1834. // https://reprap.org/wiki/MaKr3d_MaKrPanel
  1835. //
  1836. //#define MAKRPANEL
  1837. //
  1838. // Adafruit ST7565 Full Graphic Controller.
  1839. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1840. //
  1841. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1842. //
  1843. // BQ LCD Smart Controller shipped by
  1844. // default with the BQ Hephestos 2 and Witbox 2.
  1845. //
  1846. //#define BQ_LCD_SMART_CONTROLLER
  1847. //
  1848. // Cartesio UI
  1849. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1850. //
  1851. //#define CARTESIO_UI
  1852. //
  1853. // LCD for Melzi Card with Graphical LCD
  1854. //
  1855. //#define LCD_FOR_MELZI
  1856. //
  1857. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1858. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1859. //
  1860. //#define ULTI_CONTROLLER
  1861. //
  1862. // MKS MINI12864 with graphic controller and SD support
  1863. // https://reprap.org/wiki/MKS_MINI_12864
  1864. //
  1865. //#define MKS_MINI_12864
  1866. //
  1867. // MKS LCD12864A/B with graphic controller and SD support. Follows MKS_MINI_12864 pinout.
  1868. // https://www.aliexpress.com/item/33018110072.html
  1869. //
  1870. //#define MKS_LCD12864
  1871. //
  1872. // FYSETC variant of the MINI12864 graphic controller with SD support
  1873. // https://wiki.fysetc.com/Mini12864_Panel/
  1874. //
  1875. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1876. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1877. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1878. //#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight
  1879. //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight.
  1880. //
  1881. // Factory display for Creality CR-10
  1882. // https://www.aliexpress.com/item/32833148327.html
  1883. //
  1884. // This is RAMPS-compatible using a single 10-pin connector.
  1885. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1886. //
  1887. //#define CR10_STOCKDISPLAY
  1888. //
  1889. // Ender-2 OEM display, a variant of the MKS_MINI_12864
  1890. //
  1891. //#define ENDER2_STOCKDISPLAY
  1892. //
  1893. // ANET and Tronxy Graphical Controller
  1894. //
  1895. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1896. // A clone of the RepRapDiscount full graphics display but with
  1897. // different pins/wiring (see pins_ANET_10.h). Enable one of these.
  1898. //
  1899. //#define ANET_FULL_GRAPHICS_LCD
  1900. //#define ANET_FULL_GRAPHICS_LCD_ALT_WIRING
  1901. //
  1902. // AZSMZ 12864 LCD with SD
  1903. // https://www.aliexpress.com/item/32837222770.html
  1904. //
  1905. //#define AZSMZ_12864
  1906. //
  1907. // Silvergate GLCD controller
  1908. // https://github.com/android444/Silvergate
  1909. //
  1910. //#define SILVER_GATE_GLCD_CONTROLLER
  1911. //=============================================================================
  1912. //============================== OLED Displays ==============================
  1913. //=============================================================================
  1914. //
  1915. // SSD1306 OLED full graphics generic display
  1916. //
  1917. //#define U8GLIB_SSD1306
  1918. //
  1919. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1920. //
  1921. //#define SAV_3DGLCD
  1922. #if ENABLED(SAV_3DGLCD)
  1923. #define U8GLIB_SSD1306
  1924. //#define U8GLIB_SH1106
  1925. #endif
  1926. //
  1927. // TinyBoy2 128x64 OLED / Encoder Panel
  1928. //
  1929. //#define OLED_PANEL_TINYBOY2
  1930. //
  1931. // MKS OLED 1.3" 128×64 FULL GRAPHICS CONTROLLER
  1932. // https://reprap.org/wiki/MKS_12864OLED
  1933. //
  1934. // Tiny, but very sharp OLED display
  1935. //
  1936. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1937. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1938. //
  1939. // Zonestar OLED 128×64 FULL GRAPHICS CONTROLLER
  1940. //
  1941. //#define ZONESTAR_12864LCD // Graphical (DOGM) with ST7920 controller
  1942. //#define ZONESTAR_12864OLED // 1.3" OLED with SH1106 controller (default)
  1943. //#define ZONESTAR_12864OLED_SSD1306 // 0.96" OLED with SSD1306 controller
  1944. //
  1945. // Einstart S OLED SSD1306
  1946. //
  1947. //#define U8GLIB_SH1106_EINSTART
  1948. //
  1949. // Overlord OLED display/controller with i2c buzzer and LEDs
  1950. //
  1951. //#define OVERLORD_OLED
  1952. //
  1953. // FYSETC OLED 2.42" 128×64 FULL GRAPHICS CONTROLLER with WS2812 RGB
  1954. // Where to find : https://www.aliexpress.com/item/4000345255731.html
  1955. //#define FYSETC_242_OLED_12864 // Uses the SSD1309 controller
  1956. //=============================================================================
  1957. //========================== Extensible UI Displays ===========================
  1958. //=============================================================================
  1959. //
  1960. // DGUS Touch Display with DWIN OS. (Choose one.)
  1961. // ORIGIN : https://www.aliexpress.com/item/32993409517.html
  1962. // FYSETC : https://www.aliexpress.com/item/32961471929.html
  1963. //
  1964. //#define DGUS_LCD_UI_ORIGIN
  1965. //#define DGUS_LCD_UI_FYSETC
  1966. //#define DGUS_LCD_UI_HIPRECY
  1967. //
  1968. // Touch-screen LCD for Malyan M200/M300 printers
  1969. //
  1970. //#define MALYAN_LCD
  1971. #if ENABLED(MALYAN_LCD)
  1972. #define LCD_SERIAL_PORT 1 // Default is 1 for Malyan M200
  1973. #endif
  1974. //
  1975. // Touch UI for FTDI EVE (FT800/FT810) displays
  1976. // See Configuration_adv.h for all configuration options.
  1977. //
  1978. //#define TOUCH_UI_FTDI_EVE
  1979. //
  1980. // Touch-screen LCD for Anycubic printers
  1981. //
  1982. //#define ANYCUBIC_LCD_I3MEGA
  1983. //#define ANYCUBIC_LCD_CHIRON
  1984. #if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
  1985. #define LCD_SERIAL_PORT 3 // Default is 3 for Anycubic
  1986. //#define ANYCUBIC_LCD_DEBUG
  1987. #endif
  1988. //
  1989. // Third-party or vendor-customized controller interfaces.
  1990. // Sources should be installed in 'src/lcd/extui'.
  1991. //
  1992. //#define EXTENSIBLE_UI
  1993. #if ENABLED(EXTENSIBLE_UI)
  1994. //#define EXTUI_LOCAL_BEEPER // Enables use of local Beeper pin with external display
  1995. #endif
  1996. //=============================================================================
  1997. //=============================== Graphical TFTs ==============================
  1998. //=============================================================================
  1999. /**
  2000. * Specific TFT Model Presets. Enable one of the following options
  2001. * or enable TFT_GENERIC and set sub-options.
  2002. */
  2003. //
  2004. // 480x320, 3.5", SPI Display From MKS
  2005. // Normally used in MKS Robin Nano V2
  2006. //
  2007. //#define MKS_TS35_V2_0
  2008. //
  2009. // 320x240, 2.4", FSMC Display From MKS
  2010. // Normally used in MKS Robin Nano V1.2
  2011. //
  2012. //#define MKS_ROBIN_TFT24
  2013. //
  2014. // 320x240, 2.8", FSMC Display From MKS
  2015. // Normally used in MKS Robin Nano V1.2
  2016. //
  2017. //#define MKS_ROBIN_TFT28
  2018. //
  2019. // 320x240, 3.2", FSMC Display From MKS
  2020. // Normally used in MKS Robin Nano V1.2
  2021. //
  2022. //#define MKS_ROBIN_TFT32
  2023. //
  2024. // 480x320, 3.5", FSMC Display From MKS
  2025. // Normally used in MKS Robin Nano V1.2
  2026. //
  2027. //#define MKS_ROBIN_TFT35
  2028. //
  2029. // 480x272, 4.3", FSMC Display From MKS
  2030. //
  2031. //#define MKS_ROBIN_TFT43
  2032. //
  2033. // 320x240, 3.2", FSMC Display From MKS
  2034. // Normally used in MKS Robin
  2035. //
  2036. //#define MKS_ROBIN_TFT_V1_1R
  2037. //
  2038. // 480x320, 3.5", FSMC Stock Display from TronxXY
  2039. //
  2040. //#define TFT_TRONXY_X5SA
  2041. //
  2042. // 480x320, 3.5", FSMC Stock Display from AnyCubic
  2043. //
  2044. //#define ANYCUBIC_TFT35
  2045. //
  2046. // 320x240, 2.8", FSMC Stock Display from Longer/Alfawise
  2047. //
  2048. //#define LONGER_LK_TFT28
  2049. //
  2050. // 320x240, 2.8", FSMC Stock Display from ET4
  2051. //
  2052. //#define ANET_ET4_TFT28
  2053. //
  2054. // 480x320, 3.5", FSMC Stock Display from ET5
  2055. //
  2056. //#define ANET_ET5_TFT35
  2057. //
  2058. // Generic TFT with detailed options
  2059. //
  2060. //#define TFT_GENERIC
  2061. #if ENABLED(TFT_GENERIC)
  2062. // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ]
  2063. #define TFT_DRIVER AUTO
  2064. // Interface. Enable one of the following options:
  2065. //#define TFT_INTERFACE_FSMC
  2066. //#define TFT_INTERFACE_SPI
  2067. // TFT Resolution. Enable one of the following options:
  2068. //#define TFT_RES_320x240
  2069. //#define TFT_RES_480x272
  2070. //#define TFT_RES_480x320
  2071. #endif
  2072. /**
  2073. * TFT UI - User Interface Selection. Enable one of the following options:
  2074. *
  2075. * TFT_CLASSIC_UI - Emulated DOGM - 128x64 Upscaled
  2076. * TFT_COLOR_UI - Marlin Default Menus, Touch Friendly, using full TFT capabilities
  2077. * TFT_LVGL_UI - A Modern UI using LVGL
  2078. *
  2079. * For LVGL_UI also copy the 'assets' folder from the build directory to the
  2080. * root of your SD card, together with the compiled firmware.
  2081. */
  2082. //#define TFT_CLASSIC_UI
  2083. //#define TFT_COLOR_UI
  2084. //#define TFT_LVGL_UI
  2085. #if ENABLED(TFT_LVGL_UI)
  2086. //#define MKS_WIFI_MODULE // MKS WiFi module
  2087. #endif
  2088. /**
  2089. * TFT Rotation. Set to one of the following values:
  2090. *
  2091. * TFT_ROTATE_90, TFT_ROTATE_90_MIRROR_X, TFT_ROTATE_90_MIRROR_Y,
  2092. * TFT_ROTATE_180, TFT_ROTATE_180_MIRROR_X, TFT_ROTATE_180_MIRROR_Y,
  2093. * TFT_ROTATE_270, TFT_ROTATE_270_MIRROR_X, TFT_ROTATE_270_MIRROR_Y,
  2094. * TFT_MIRROR_X, TFT_MIRROR_Y, TFT_NO_ROTATION
  2095. */
  2096. //#define TFT_ROTATION TFT_NO_ROTATION
  2097. //=============================================================================
  2098. //============================ Other Controllers ============================
  2099. //=============================================================================
  2100. //
  2101. // Ender-3 v2 OEM display. A DWIN display with Rotary Encoder.
  2102. //
  2103. //#define DWIN_CREALITY_LCD
  2104. //
  2105. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  2106. //
  2107. //#define TOUCH_SCREEN
  2108. #if ENABLED(TOUCH_SCREEN)
  2109. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  2110. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  2111. #define TOUCH_SCREEN_CALIBRATION
  2112. //#define TOUCH_CALIBRATION_X 12316
  2113. //#define TOUCH_CALIBRATION_Y -8981
  2114. //#define TOUCH_OFFSET_X -43
  2115. //#define TOUCH_OFFSET_Y 257
  2116. //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
  2117. #if ENABLED(TFT_COLOR_UI)
  2118. //#define SINGLE_TOUCH_NAVIGATION
  2119. #endif
  2120. #endif
  2121. //
  2122. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  2123. // https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/
  2124. //
  2125. //#define REPRAPWORLD_KEYPAD
  2126. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  2127. //=============================================================================
  2128. //=============================== Extra Features ==============================
  2129. //=============================================================================
  2130. // @section extras
  2131. // Set number of user-controlled fans. Disable to use all board-defined fans.
  2132. // :[1,2,3,4,5,6,7,8]
  2133. //#define NUM_M106_FANS 1
  2134. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  2135. //#define FAST_PWM_FAN
  2136. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  2137. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  2138. // is too low, you should also increment SOFT_PWM_SCALE.
  2139. //#define FAN_SOFT_PWM
  2140. // Incrementing this by 1 will double the software PWM frequency,
  2141. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  2142. // However, control resolution will be halved for each increment;
  2143. // at zero value, there are 128 effective control positions.
  2144. // :[0,1,2,3,4,5,6,7]
  2145. #define SOFT_PWM_SCALE 0
  2146. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  2147. // be used to mitigate the associated resolution loss. If enabled,
  2148. // some of the PWM cycles are stretched so on average the desired
  2149. // duty cycle is attained.
  2150. //#define SOFT_PWM_DITHER
  2151. // Temperature status LEDs that display the hotend and bed temperature.
  2152. // If all hotends, bed temperature, and target temperature are under 54C
  2153. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  2154. //#define TEMP_STAT_LEDS
  2155. // Support for the BariCUDA Paste Extruder
  2156. //#define BARICUDA
  2157. // Support for BlinkM/CyzRgb
  2158. //#define BLINKM
  2159. // Support for PCA9632 PWM LED driver
  2160. //#define PCA9632
  2161. // Support for PCA9533 PWM LED driver
  2162. //#define PCA9533
  2163. /**
  2164. * RGB LED / LED Strip Control
  2165. *
  2166. * Enable support for an RGB LED connected to 5V digital pins, or
  2167. * an RGB Strip connected to MOSFETs controlled by digital pins.
  2168. *
  2169. * Adds the M150 command to set the LED (or LED strip) color.
  2170. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  2171. * luminance values can be set from 0 to 255.
  2172. * For NeoPixel LED an overall brightness parameter is also available.
  2173. *
  2174. * *** CAUTION ***
  2175. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  2176. * as the Arduino cannot handle the current the LEDs will require.
  2177. * Failure to follow this precaution can destroy your Arduino!
  2178. * NOTE: A separate 5V power supply is required! The NeoPixel LED needs
  2179. * more current than the Arduino 5V linear regulator can produce.
  2180. * *** CAUTION ***
  2181. *
  2182. * LED Type. Enable only one of the following two options.
  2183. */
  2184. //#define RGB_LED
  2185. //#define RGBW_LED
  2186. #if EITHER(RGB_LED, RGBW_LED)
  2187. //#define RGB_LED_R_PIN 34
  2188. //#define RGB_LED_G_PIN 43
  2189. //#define RGB_LED_B_PIN 35
  2190. //#define RGB_LED_W_PIN -1
  2191. #endif
  2192. // Support for Adafruit NeoPixel LED driver
  2193. //#define NEOPIXEL_LED
  2194. #if ENABLED(NEOPIXEL_LED)
  2195. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  2196. #define NEOPIXEL_PIN 4 // LED driving pin
  2197. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  2198. //#define NEOPIXEL2_PIN 5
  2199. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
  2200. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  2201. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  2202. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  2203. // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
  2204. //#define NEOPIXEL2_SEPARATE
  2205. #if ENABLED(NEOPIXEL2_SEPARATE)
  2206. #define NEOPIXEL2_PIXELS 15 // Number of LEDs in the second strip
  2207. #define NEOPIXEL2_BRIGHTNESS 127 // Initial brightness (0-255)
  2208. #define NEOPIXEL2_STARTUP_TEST // Cycle through colors at startup
  2209. #else
  2210. //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel
  2211. #endif
  2212. // Use a single NeoPixel LED for static (background) lighting
  2213. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  2214. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  2215. #endif
  2216. /**
  2217. * Printer Event LEDs
  2218. *
  2219. * During printing, the LEDs will reflect the printer status:
  2220. *
  2221. * - Gradually change from blue to violet as the heated bed gets to target temp
  2222. * - Gradually change from violet to red as the hotend gets to temperature
  2223. * - Change to white to illuminate work surface
  2224. * - Change to green once print has finished
  2225. * - Turn off after the print has finished and the user has pushed a button
  2226. */
  2227. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  2228. #define PRINTER_EVENT_LEDS
  2229. #endif
  2230. /**
  2231. * Number of servos
  2232. *
  2233. * For some servo-related options NUM_SERVOS will be set automatically.
  2234. * Set this manually if there are extra servos needing manual control.
  2235. * Set to 0 to turn off servo support.
  2236. */
  2237. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  2238. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  2239. // 300ms is a good value but you can try less delay.
  2240. // If the servo can't reach the requested position, increase it.
  2241. #define SERVO_DELAY { 300 }
  2242. // Only power servos during movement, otherwise leave off to prevent jitter
  2243. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  2244. // Edit servo angles with M281 and save to EEPROM with M500
  2245. //#define EDITABLE_SERVO_ANGLES