My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Nevar pievienot vairāk kā 25 tēmas Tēmai ir jāsākas ar burtu vai ciparu, tā var saturēt domu zīmes ('-') un var būt līdz 35 simboliem gara.

Configuration.h 79KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510610710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916016116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321421521621721821922022122222322422522622722822923023123223323423523623723823924024124224324424524624724824925025125225325425525625725825926026126226326426526626726826927027127227327427527627727827928028128228328428528628728828929029129229329429529629729829930030130230330430530630730830931031131231331431531631731831932032132232332432532632732832933033133233333433533633733833934034134234334434534634734834935035135235335435535635735835936036136236336436536636736836937037137237337437537637737837938038138238338438538638738838939039139239339439539639739839940040140240340440540640740840941041141241341441541641741841942042142242342442542642742842943043143243343443543643743843944044144244344444544644744844945045145245345445545645745845946046146246346446546646746846947047147247347447547647747847948048148248348448548648748848949049149249349449549649749849950050150250350450550650750850951051151251351451551651751851952052152252352452552652752852953053153253353453553653753853954054154254354454554654754854955055155255355455555655755855956056156256356456556656756856957057157257357457557657757857958058158258358458558658758858959059159259359459559659759859960060160260360460560660760860961061161261361461561661761861962062162262362462562662762862963063163263363463563663763863964064164264364464564664764864965065165265365465565665765865966066166266366466566666766866967067167267367467567667767867968068168268368468568668768868969069169269369469569669769869970070170270370470570670770870971071171271371471571671771871972072172272372472572672772872973073173273373473573673773873974074174274374474574674774874975075175275375475575675775875976076176276376476576676776876977077177277377477577677777877978078178278378478578678778878979079179279379479579679779879980080180280380480580680780880981081181281381481581681781881982082182282382482582682782882983083183283383483583683783883984084184284384484584684784884985085185285385485585685785885986086186286386486586686786886987087187287387487587687787887988088188288388488588688788888989089189289389489589689789889990090190290390490590690790890991091191291391491591691791891992092192292392492592692792892993093193293393493593693793893994094194294394494594694794894995095195295395495595695795895996096196296396496596696796896997097197297397497597697797897998098198298398498598698798898999099199299399499599699799899910001001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025102610271028102910301031103210331034103510361037103810391040104110421043104410451046104710481049105010511052105310541055105610571058105910601061106210631064106510661067106810691070107110721073107410751076107710781079108010811082108310841085108610871088108910901091109210931094109510961097109810991100110111021103110411051106110711081109111011111112111311141115111611171118111911201121112211231124112511261127112811291130113111321133113411351136113711381139114011411142114311441145114611471148114911501151115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175117611771178117911801181118211831184118511861187118811891190119111921193119411951196119711981199120012011202120312041205120612071208120912101211121212131214121512161217121812191220122112221223122412251226122712281229123012311232123312341235123612371238123912401241124212431244124512461247124812491250125112521253125412551256125712581259126012611262126312641265126612671268126912701271127212731274127512761277127812791280128112821283128412851286128712881289129012911292129312941295129612971298129913001301130213031304130513061307130813091310131113121313131413151316131713181319132013211322132313241325132613271328132913301331133213331334133513361337133813391340134113421343134413451346134713481349135013511352135313541355135613571358135913601361136213631364136513661367136813691370137113721373137413751376137713781379138013811382138313841385138613871388138913901391139213931394139513961397139813991400140114021403140414051406140714081409141014111412141314141415141614171418141914201421142214231424142514261427142814291430143114321433143414351436143714381439144014411442144314441445144614471448144914501451145214531454145514561457145814591460146114621463146414651466146714681469147014711472147314741475147614771478147914801481148214831484148514861487148814891490149114921493149414951496149714981499150015011502150315041505150615071508150915101511151215131514151515161517151815191520152115221523152415251526152715281529153015311532153315341535153615371538153915401541154215431544154515461547154815491550155115521553155415551556155715581559156015611562156315641565156615671568156915701571157215731574157515761577157815791580158115821583158415851586158715881589159015911592159315941595159615971598159916001601160216031604160516061607160816091610161116121613161416151616161716181619162016211622162316241625162616271628162916301631163216331634163516361637163816391640164116421643164416451646164716481649165016511652165316541655165616571658165916601661166216631664166516661667166816691670167116721673167416751676167716781679168016811682168316841685168616871688168916901691169216931694169516961697169816991700170117021703170417051706170717081709171017111712171317141715171617171718171917201721172217231724172517261727172817291730173117321733173417351736173717381739174017411742174317441745174617471748174917501751175217531754175517561757175817591760176117621763176417651766176717681769177017711772177317741775177617771778177917801781178217831784178517861787178817891790179117921793179417951796179717981799180018011802180318041805180618071808180918101811181218131814181518161817181818191820182118221823182418251826182718281829183018311832183318341835183618371838183918401841184218431844184518461847184818491850185118521853185418551856185718581859186018611862186318641865186618671868186918701871187218731874187518761877187818791880188118821883188418851886188718881889189018911892189318941895189618971898189919001901190219031904190519061907190819091910191119121913191419151916191719181919192019211922192319241925192619271928192919301931193219331934193519361937193819391940194119421943194419451946194719481949195019511952195319541955195619571958195919601961196219631964196519661967196819691970197119721973197419751976197719781979198019811982198319841985198619871988198919901991199219931994199519961997199819992000200120022003200420052006200720082009201020112012201320142015201620172018201920202021202220232024202520262027202820292030203120322033203420352036203720382039204020412042204320442045204620472048204920502051205220532054205520562057205820592060206120622063206420652066206720682069207020712072207320742075207620772078207920802081208220832084208520862087208820892090209120922093209420952096209720982099210021012102210321042105210621072108210921102111211221132114211521162117211821192120212121222123212421252126212721282129213021312132213321342135213621372138213921402141214221432144214521462147214821492150215121522153215421552156215721582159216021612162216321642165216621672168216921702171217221732174217521762177217821792180218121822183218421852186218721882189219021912192219321942195219621972198219922002201220222032204220522062207220822092210
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #define CONFIGURATION_H_VERSION 020000
  39. //===========================================================================
  40. //============================= Getting Started =============================
  41. //===========================================================================
  42. /**
  43. * Here are some standard links for getting your machine calibrated:
  44. *
  45. * http://reprap.org/wiki/Calibration
  46. * http://youtu.be/wAL9d7FgInk
  47. * http://calculator.josefprusa.cz
  48. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  49. * http://www.thingiverse.com/thing:5573
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * http://www.thingiverse.com/thing:298812
  52. */
  53. //===========================================================================
  54. //============================= DELTA Printer ===============================
  55. //===========================================================================
  56. // For a Delta printer start with one of the configuration files in the
  57. // config/examples/delta directory and customize for your machine.
  58. //
  59. //===========================================================================
  60. //============================= SCARA Printer ===============================
  61. //===========================================================================
  62. // For a SCARA printer start with the configuration files in
  63. // config/examples/SCARA and customize for your machine.
  64. //
  65. // @section info
  66. // Author info of this build printed to the host during boot and M115
  67. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  68. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  69. /**
  70. * *** VENDORS PLEASE READ ***
  71. *
  72. * Marlin allows you to add a custom boot image for Graphical LCDs.
  73. * With this option Marlin will first show your custom screen followed
  74. * by the standard Marlin logo with version number and web URL.
  75. *
  76. * We encourage you to take advantage of this new feature and we also
  77. * respectfully request that you retain the unmodified Marlin boot screen.
  78. */
  79. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  80. #define SHOW_BOOTSCREEN
  81. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  82. //#define SHOW_CUSTOM_BOOTSCREEN
  83. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  84. //#define CUSTOM_STATUS_SCREEN_IMAGE
  85. // @section machine
  86. /**
  87. * Select the serial port on the board to use for communication with the host.
  88. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT -1
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  97. * Serial port -1 is the USB emulated serial port, if available.
  98. *
  99. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  100. */
  101. // #define SERIAL_PORT_2 3
  102. /**
  103. * This setting determines the communication speed of the printer.
  104. *
  105. * 250000 works in most cases, but you might try a lower speed if
  106. * you commonly experience drop-outs during host printing.
  107. * You may try up to 1000000 to speed up SD file transfer.
  108. *
  109. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  110. */
  111. #define BAUDRATE 250000
  112. // Enable the Bluetooth serial interface on AT90USB devices
  113. //#define BLUETOOTH
  114. // Choose the name from boards.h that matches your setup
  115. #ifndef MOTHERBOARD
  116. #define MOTHERBOARD BOARD_ARMED
  117. #endif
  118. // Name displayed in the LCD "Ready" message and Info menu
  119. //#define CUSTOM_MACHINE_NAME "3D Printer"
  120. // Printer's unique ID, used by some programs to differentiate between machines.
  121. // Choose your own or use a service like http://www.uuidgenerator.net/version4
  122. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  123. // @section extruder
  124. // This defines the number of extruders
  125. // :[1, 2, 3, 4, 5, 6]
  126. #define EXTRUDERS 1
  127. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  128. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  129. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  130. //#define SINGLENOZZLE
  131. /**
  132. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  133. *
  134. * This device allows one stepper driver on a control board to drive
  135. * two to eight stepper motors, one at a time, in a manner suitable
  136. * for extruders.
  137. *
  138. * This option only allows the multiplexer to switch on tool-change.
  139. * Additional options to configure custom E moves are pending.
  140. */
  141. //#define MK2_MULTIPLEXER
  142. #if ENABLED(MK2_MULTIPLEXER)
  143. // Override the default DIO selector pins here, if needed.
  144. // Some pins files may provide defaults for these pins.
  145. //#define E_MUX0_PIN 40 // Always Required
  146. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  147. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  148. #endif
  149. /**
  150. * Prusa Multi-Material Unit v2
  151. *
  152. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  153. * Requires EXTRUDERS = 5
  154. *
  155. * For additional configuration see Configuration_adv.h
  156. */
  157. //#define PRUSA_MMU2
  158. // A dual extruder that uses a single stepper motor
  159. //#define SWITCHING_EXTRUDER
  160. #if ENABLED(SWITCHING_EXTRUDER)
  161. #define SWITCHING_EXTRUDER_SERVO_NR 0
  162. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  163. #if EXTRUDERS > 3
  164. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  165. #endif
  166. #endif
  167. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  168. //#define SWITCHING_NOZZLE
  169. #if ENABLED(SWITCHING_NOZZLE)
  170. #define SWITCHING_NOZZLE_SERVO_NR 0
  171. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  172. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  173. #endif
  174. /**
  175. * Two separate X-carriages with extruders that connect to a moving part
  176. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  177. */
  178. //#define PARKING_EXTRUDER
  179. /**
  180. * Two separate X-carriages with extruders that connect to a moving part
  181. * via a magnetic docking mechanism using movements and no solenoid
  182. *
  183. * project : https://www.thingiverse.com/thing:3080893
  184. * movements : https://youtu.be/0xCEiG9VS3k
  185. * https://youtu.be/Bqbcs0CU2FE
  186. */
  187. //#define MAGNETIC_PARKING_EXTRUDER
  188. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  189. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  190. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  191. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  192. #if ENABLED(PARKING_EXTRUDER)
  193. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  194. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  195. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  196. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  197. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  198. #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
  199. #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
  200. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  201. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  202. #endif
  203. #endif
  204. /**
  205. * Switching Toolhead
  206. *
  207. * Support for swappable and dockable toolheads, such as
  208. * the E3D Tool Changer. Toolheads are locked with a servo.
  209. */
  210. //#define SWITCHING_TOOLHEAD
  211. /**
  212. * Magnetic Switching Toolhead
  213. *
  214. * Support swappable and dockable toolheads with a magnetic
  215. * docking mechanism using movement and no servo.
  216. */
  217. //#define MAGNETIC_SWITCHING_TOOLHEAD
  218. /**
  219. * Electromagnetic Switching Toolhead
  220. *
  221. * Parking for CoreXY / HBot kinematics.
  222. * Toolheads are parked at one edge and held with an electromagnet.
  223. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  224. */
  225. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  226. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  227. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  228. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  229. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  230. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  231. #if ENABLED(SWITCHING_TOOLHEAD)
  232. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  233. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  234. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  235. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  236. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  237. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  238. #if ENABLED(PRIME_BEFORE_REMOVE)
  239. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  240. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  241. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate
  242. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate
  243. #endif
  244. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  245. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  246. #endif
  247. #endif
  248. /**
  249. * "Mixing Extruder"
  250. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  251. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  252. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  253. * - This implementation supports up to two mixing extruders.
  254. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  255. */
  256. //#define MIXING_EXTRUDER
  257. #if ENABLED(MIXING_EXTRUDER)
  258. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  259. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  260. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  261. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  262. #if ENABLED(GRADIENT_MIX)
  263. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  264. #endif
  265. #endif
  266. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  267. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  268. // For the other hotends it is their distance from the extruder 0 hotend.
  269. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  270. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  271. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  272. // @section machine
  273. /**
  274. * Power Supply Control
  275. *
  276. * Enable and connect the power supply to the PS_ON_PIN.
  277. * Specify whether the power supply is active HIGH or active LOW.
  278. */
  279. //#define PSU_CONTROL
  280. //#define PSU_NAME "Power Supply"
  281. #if ENABLED(PSU_CONTROL)
  282. #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
  283. //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80
  284. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  285. #if ENABLED(AUTO_POWER_CONTROL)
  286. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  287. #define AUTO_POWER_E_FANS
  288. #define AUTO_POWER_CONTROLLERFAN
  289. #define AUTO_POWER_CHAMBER_FAN
  290. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature
  291. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature
  292. #define POWER_TIMEOUT 30
  293. #endif
  294. #endif
  295. // @section temperature
  296. //===========================================================================
  297. //============================= Thermal Settings ============================
  298. //===========================================================================
  299. /**
  300. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  301. *
  302. * Temperature sensors available:
  303. *
  304. * -4 : thermocouple with AD8495
  305. * -3 : thermocouple with MAX31855 (only for sensor 0)
  306. * -2 : thermocouple with MAX6675 (only for sensor 0)
  307. * -1 : thermocouple with AD595
  308. * 0 : not used
  309. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  310. * 331 : (3.3V scaled thermistor 1 table)
  311. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  312. * 3 : Mendel-parts thermistor (4.7k pullup)
  313. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  314. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  315. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  316. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  317. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  318. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  319. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  320. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  321. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  322. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  323. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  324. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  325. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  326. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  327. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  328. * 20 : Pt100 with circuit in the Ultimainboard V2.x
  329. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  330. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  331. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  332. * 66 : 4.7M High Temperature thermistor from Dyze Design
  333. * 67 : 450C thermistor from SliceEngineering
  334. * 70 : the 100K thermistor found in the bq Hephestos 2
  335. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  336. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  337. *
  338. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  339. * (but gives greater accuracy and more stable PID)
  340. * 51 : 100k thermistor - EPCOS (1k pullup)
  341. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  342. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  343. *
  344. * 1047 : Pt1000 with 4k7 pullup
  345. * 1010 : Pt1000 with 1k pullup (non standard)
  346. * 147 : Pt100 with 4k7 pullup
  347. * 110 : Pt100 with 1k pullup (non standard)
  348. *
  349. * 1000 : Custom - Specify parameters in Configuration_adv.h
  350. *
  351. * Use these for Testing or Development purposes. NEVER for production machine.
  352. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  353. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  354. */
  355. #define TEMP_SENSOR_0 5
  356. #define TEMP_SENSOR_1 0
  357. #define TEMP_SENSOR_2 0
  358. #define TEMP_SENSOR_3 0
  359. #define TEMP_SENSOR_4 0
  360. #define TEMP_SENSOR_5 0
  361. #define TEMP_SENSOR_BED 13
  362. #define TEMP_SENSOR_CHAMBER 0
  363. // Dummy thermistor constant temperature readings, for use with 998 and 999
  364. #define DUMMY_THERMISTOR_998_VALUE 25
  365. #define DUMMY_THERMISTOR_999_VALUE 100
  366. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  367. // from the two sensors differ too much the print will be aborted.
  368. //#define TEMP_SENSOR_1_AS_REDUNDANT
  369. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  370. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  371. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  372. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  373. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  374. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  375. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  376. // Below this temperature the heater will be switched off
  377. // because it probably indicates a broken thermistor wire.
  378. #define HEATER_0_MINTEMP 5
  379. #define HEATER_1_MINTEMP 5
  380. #define HEATER_2_MINTEMP 5
  381. #define HEATER_3_MINTEMP 5
  382. #define HEATER_4_MINTEMP 5
  383. #define HEATER_5_MINTEMP 5
  384. #define BED_MINTEMP 5
  385. // Above this temperature the heater will be switched off.
  386. // This can protect components from overheating, but NOT from shorts and failures.
  387. // (Use MINTEMP for thermistor short/failure protection.)
  388. #define HEATER_0_MAXTEMP 275
  389. #define HEATER_1_MAXTEMP 275
  390. #define HEATER_2_MAXTEMP 275
  391. #define HEATER_3_MAXTEMP 275
  392. #define HEATER_4_MAXTEMP 275
  393. #define HEATER_5_MAXTEMP 275
  394. #define BED_MAXTEMP 150
  395. //===========================================================================
  396. //============================= PID Settings ================================
  397. //===========================================================================
  398. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  399. // Comment the following line to disable PID and enable bang-bang.
  400. #define PIDTEMP
  401. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  402. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  403. #define PID_K1 0.95 // Smoothing factor within any PID loop
  404. #if ENABLED(PIDTEMP)
  405. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  406. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  407. //#define PID_DEBUG // Sends debug data to the serial port.
  408. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  409. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  410. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  411. // Set/get with gcode: M301 E[extruder number, 0-2]
  412. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  413. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  414. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  415. // Armed
  416. #define DEFAULT_Kp 23.41
  417. #define DEFAULT_Ki 2.57
  418. #define DEFAULT_Kd 53.37
  419. // MakerGear
  420. //#define DEFAULT_Kp 7.0
  421. //#define DEFAULT_Ki 0.1
  422. //#define DEFAULT_Kd 12
  423. // Mendel Parts V9 on 12V
  424. //#define DEFAULT_Kp 63.0
  425. //#define DEFAULT_Ki 2.25
  426. //#define DEFAULT_Kd 440
  427. #endif // PIDTEMP
  428. //===========================================================================
  429. //====================== PID > Bed Temperature Control ======================
  430. //===========================================================================
  431. /**
  432. * PID Bed Heating
  433. *
  434. * If this option is enabled set PID constants below.
  435. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  436. *
  437. * The PID frequency will be the same as the extruder PWM.
  438. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  439. * which is fine for driving a square wave into a resistive load and does not significantly
  440. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  441. * heater. If your configuration is significantly different than this and you don't understand
  442. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  443. */
  444. //#define PIDTEMPBED
  445. //#define BED_LIMIT_SWITCHING
  446. /**
  447. * Max Bed Power
  448. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  449. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  450. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  451. */
  452. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  453. #if ENABLED(PIDTEMPBED)
  454. //#define MIN_BED_POWER 0
  455. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  456. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  457. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  458. #define DEFAULT_bedKp 144.87
  459. #define DEFAULT_bedKi 27.00
  460. #define DEFAULT_bedKd 194.30
  461. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  462. //from pidautotune
  463. //#define DEFAULT_bedKp 97.1
  464. //#define DEFAULT_bedKi 1.41
  465. //#define DEFAULT_bedKd 1675.16
  466. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  467. #endif // PIDTEMPBED
  468. // @section extruder
  469. /**
  470. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  471. * Add M302 to set the minimum extrusion temperature and/or turn
  472. * cold extrusion prevention on and off.
  473. *
  474. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  475. */
  476. #define PREVENT_COLD_EXTRUSION
  477. #define EXTRUDE_MINTEMP 170
  478. /**
  479. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  480. * Note: For Bowden Extruders make this large enough to allow load/unload.
  481. */
  482. #define PREVENT_LENGTHY_EXTRUDE
  483. #define EXTRUDE_MAXLENGTH 200
  484. //===========================================================================
  485. //======================== Thermal Runaway Protection =======================
  486. //===========================================================================
  487. /**
  488. * Thermal Protection provides additional protection to your printer from damage
  489. * and fire. Marlin always includes safe min and max temperature ranges which
  490. * protect against a broken or disconnected thermistor wire.
  491. *
  492. * The issue: If a thermistor falls out, it will report the much lower
  493. * temperature of the air in the room, and the the firmware will keep
  494. * the heater on.
  495. *
  496. * If you get "Thermal Runaway" or "Heating failed" errors the
  497. * details can be tuned in Configuration_adv.h
  498. */
  499. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  500. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  501. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  502. //===========================================================================
  503. //============================= Mechanical Settings =========================
  504. //===========================================================================
  505. // @section machine
  506. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  507. // either in the usual order or reversed
  508. //#define COREXY
  509. //#define COREXZ
  510. //#define COREYZ
  511. //#define COREYX
  512. //#define COREZX
  513. //#define COREZY
  514. //===========================================================================
  515. //============================== Endstop Settings ===========================
  516. //===========================================================================
  517. // @section homing
  518. // Specify here all the endstop connectors that are connected to any endstop or probe.
  519. // Almost all printers will be using one per axis. Probes will use one or more of the
  520. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  521. #define USE_XMIN_PLUG
  522. #define USE_YMIN_PLUG
  523. #define USE_ZMIN_PLUG
  524. //#define USE_XMAX_PLUG
  525. //#define USE_YMAX_PLUG
  526. //#define USE_ZMAX_PLUG
  527. // Enable pullup for all endstops to prevent a floating state
  528. #define ENDSTOPPULLUPS
  529. #if DISABLED(ENDSTOPPULLUPS)
  530. // Disable ENDSTOPPULLUPS to set pullups individually
  531. //#define ENDSTOPPULLUP_XMAX
  532. //#define ENDSTOPPULLUP_YMAX
  533. //#define ENDSTOPPULLUP_ZMAX
  534. //#define ENDSTOPPULLUP_XMIN
  535. //#define ENDSTOPPULLUP_YMIN
  536. //#define ENDSTOPPULLUP_ZMIN
  537. //#define ENDSTOPPULLUP_ZMIN_PROBE
  538. #endif
  539. // Enable pulldown for all endstops to prevent a floating state
  540. //#define ENDSTOPPULLDOWNS
  541. #if DISABLED(ENDSTOPPULLDOWNS)
  542. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  543. //#define ENDSTOPPULLDOWN_XMAX
  544. //#define ENDSTOPPULLDOWN_YMAX
  545. //#define ENDSTOPPULLDOWN_ZMAX
  546. //#define ENDSTOPPULLDOWN_XMIN
  547. //#define ENDSTOPPULLDOWN_YMIN
  548. //#define ENDSTOPPULLDOWN_ZMIN
  549. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  550. #endif
  551. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  552. #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  553. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  554. #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  555. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  556. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  557. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  558. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
  559. /**
  560. * Stepper Drivers
  561. *
  562. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  563. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  564. *
  565. * A4988 is assumed for unspecified drivers.
  566. *
  567. * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  568. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  569. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  570. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  571. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  572. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  573. */
  574. //#define X_DRIVER_TYPE A4988
  575. //#define Y_DRIVER_TYPE A4988
  576. //#define Z_DRIVER_TYPE A4988
  577. //#define X2_DRIVER_TYPE A4988
  578. //#define Y2_DRIVER_TYPE A4988
  579. //#define Z2_DRIVER_TYPE A4988
  580. //#define Z3_DRIVER_TYPE A4988
  581. //#define E0_DRIVER_TYPE A4988
  582. //#define E1_DRIVER_TYPE A4988
  583. //#define E2_DRIVER_TYPE A4988
  584. //#define E3_DRIVER_TYPE A4988
  585. //#define E4_DRIVER_TYPE A4988
  586. //#define E5_DRIVER_TYPE A4988
  587. // Enable this feature if all enabled endstop pins are interrupt-capable.
  588. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  589. //#define ENDSTOP_INTERRUPTS_FEATURE
  590. /**
  591. * Endstop Noise Threshold
  592. *
  593. * Enable if your probe or endstops falsely trigger due to noise.
  594. *
  595. * - Higher values may affect repeatability or accuracy of some bed probes.
  596. * - To fix noise install a 100nF ceramic capacitor inline with the switch.
  597. * - This feature is not required for common micro-switches mounted on PCBs
  598. * based on the Makerbot design, which already have the 100nF capacitor.
  599. *
  600. * :[2,3,4,5,6,7]
  601. */
  602. //#define ENDSTOP_NOISE_THRESHOLD 2
  603. //=============================================================================
  604. //============================== Movement Settings ============================
  605. //=============================================================================
  606. // @section motion
  607. /**
  608. * Default Settings
  609. *
  610. * These settings can be reset by M502
  611. *
  612. * Note that if EEPROM is enabled, saved values will override these.
  613. */
  614. /**
  615. * With this option each E stepper can have its own factors for the
  616. * following movement settings. If fewer factors are given than the
  617. * total number of extruders, the last value applies to the rest.
  618. */
  619. //#define DISTINCT_E_FACTORS
  620. /**
  621. * Default Axis Steps Per Unit (steps/mm)
  622. * Override with M92
  623. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  624. */
  625. #define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 156.84 }
  626. /**
  627. * Default Max Feed Rate (mm/s)
  628. * Override with M203
  629. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  630. */
  631. #define DEFAULT_MAX_FEEDRATE { 300, 300, 20, 120 }
  632. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  633. #if ENABLED(LIMITED_MAX_FR_EDITING)
  634. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  635. #endif
  636. /**
  637. * Default Max Acceleration (change/s) change = mm/s
  638. * (Maximum start speed for accelerated moves)
  639. * Override with M201
  640. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  641. */
  642. #define DEFAULT_MAX_ACCELERATION { 1000, 1000, 1000, 5000 }
  643. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  644. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  645. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  646. #endif
  647. /**
  648. * Default Acceleration (change/s) change = mm/s
  649. * Override with M204
  650. *
  651. * M204 P Acceleration
  652. * M204 R Retract Acceleration
  653. * M204 T Travel Acceleration
  654. */
  655. #define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
  656. #define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
  657. #define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
  658. /**
  659. * Default Jerk limits (mm/s)
  660. * Override with M205 X Y Z E
  661. *
  662. * "Jerk" specifies the minimum speed change that requires acceleration.
  663. * When changing speed and direction, if the difference is less than the
  664. * value set here, it may happen instantaneously.
  665. */
  666. //#define CLASSIC_JERK
  667. #if ENABLED(CLASSIC_JERK)
  668. #define DEFAULT_XJERK 8.0
  669. #define DEFAULT_YJERK 8.0
  670. #define DEFAULT_ZJERK 0.4
  671. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  672. #if ENABLED(LIMITED_JERK_EDITING)
  673. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  674. #endif
  675. #endif
  676. #define DEFAULT_EJERK 1.5 // May be used by Linear Advance
  677. /**
  678. * Junction Deviation Factor
  679. *
  680. * See:
  681. * https://reprap.org/forum/read.php?1,739819
  682. * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  683. */
  684. #if DISABLED(CLASSIC_JERK)
  685. #define JUNCTION_DEVIATION_MM 0.026 // (mm) Distance from real junction edge
  686. #endif
  687. /**
  688. * S-Curve Acceleration
  689. *
  690. * This option eliminates vibration during printing by fitting a Bézier
  691. * curve to move acceleration, producing much smoother direction changes.
  692. *
  693. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  694. */
  695. //#define S_CURVE_ACCELERATION
  696. //===========================================================================
  697. //============================= Z Probe Options =============================
  698. //===========================================================================
  699. // @section probes
  700. //
  701. // See http://marlinfw.org/docs/configuration/probes.html
  702. //
  703. /**
  704. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  705. *
  706. * Enable this option for a probe connected to the Z Min endstop pin.
  707. */
  708. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  709. /**
  710. * Z_MIN_PROBE_PIN
  711. *
  712. * Define this pin if the probe is not connected to Z_MIN_PIN.
  713. * If not defined the default pin for the selected MOTHERBOARD
  714. * will be used. Most of the time the default is what you want.
  715. *
  716. * - The simplest option is to use a free endstop connector.
  717. * - Use 5V for powered (usually inductive) sensors.
  718. *
  719. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  720. * - For simple switches connect...
  721. * - normally-closed switches to GND and D32.
  722. * - normally-open switches to 5V and D32.
  723. *
  724. */
  725. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  726. /**
  727. * Probe Type
  728. *
  729. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  730. * Activate one of these to use Auto Bed Leveling below.
  731. */
  732. /**
  733. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  734. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  735. * or (with LCD_BED_LEVELING) the LCD controller.
  736. */
  737. //#define PROBE_MANUALLY
  738. //#define MANUAL_PROBE_START_Z 0.2
  739. /**
  740. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  741. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  742. */
  743. //#define FIX_MOUNTED_PROBE
  744. /**
  745. * Z Servo Probe, such as an endstop switch on a rotating arm.
  746. */
  747. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  748. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  749. /**
  750. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  751. */
  752. //#define BLTOUCH
  753. /**
  754. * Touch-MI Probe by hotends.fr
  755. *
  756. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  757. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  758. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  759. *
  760. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  761. * and a minimum Z_HOMING_HEIGHT of 10.
  762. */
  763. //#define TOUCH_MI_PROBE
  764. #if ENABLED(TOUCH_MI_PROBE)
  765. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  766. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  767. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  768. #endif
  769. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  770. //#define SOLENOID_PROBE
  771. // A sled-mounted probe like those designed by Charles Bell.
  772. //#define Z_PROBE_SLED
  773. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  774. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  775. //#define RACK_AND_PINION_PROBE
  776. #if ENABLED(RACK_AND_PINION_PROBE)
  777. #define Z_PROBE_DEPLOY_X X_MIN_POS
  778. #define Z_PROBE_RETRACT_X X_MAX_POS
  779. #endif
  780. //
  781. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  782. //
  783. /**
  784. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  785. *
  786. * In the following example the X and Y offsets are both positive:
  787. *
  788. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  789. *
  790. * +-- BACK ---+
  791. * | |
  792. * L | (+) P | R <-- probe (20,20)
  793. * E | | I
  794. * F | (-) N (+) | G <-- nozzle (10,10)
  795. * T | | H
  796. * | (-) | T
  797. * | |
  798. * O-- FRONT --+
  799. * (0,0)
  800. *
  801. * Specify a Probe position as { X, Y, Z }
  802. */
  803. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  804. // Certain types of probes need to stay away from edges
  805. #define MIN_PROBE_EDGE 10
  806. // X and Y axis travel speed (mm/m) between probes
  807. #define XY_PROBE_SPEED 8000
  808. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  809. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  810. // Feedrate (mm/m) for the "accurate" probe of each point
  811. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  812. /**
  813. * Multiple Probing
  814. *
  815. * You may get improved results by probing 2 or more times.
  816. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  817. *
  818. * A total of 2 does fast/slow probes with a weighted average.
  819. * A total of 3 or more adds more slow probes, taking the average.
  820. */
  821. //#define MULTIPLE_PROBING 2
  822. //#define EXTRA_PROBING 1
  823. /**
  824. * Z probes require clearance when deploying, stowing, and moving between
  825. * probe points to avoid hitting the bed and other hardware.
  826. * Servo-mounted probes require extra space for the arm to rotate.
  827. * Inductive probes need space to keep from triggering early.
  828. *
  829. * Use these settings to specify the distance (mm) to raise the probe (or
  830. * lower the bed). The values set here apply over and above any (negative)
  831. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  832. * Only integer values >= 1 are valid here.
  833. *
  834. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  835. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  836. */
  837. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  838. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  839. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  840. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  841. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  842. // For M851 give a range for adjusting the Z probe offset
  843. #define Z_PROBE_OFFSET_RANGE_MIN -20
  844. #define Z_PROBE_OFFSET_RANGE_MAX 20
  845. // Enable the M48 repeatability test to test probe accuracy
  846. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  847. // Before deploy/stow pause for user confirmation
  848. //#define PAUSE_BEFORE_DEPLOY_STOW
  849. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  850. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  851. #endif
  852. /**
  853. * Enable one or more of the following if probing seems unreliable.
  854. * Heaters and/or fans can be disabled during probing to minimize electrical
  855. * noise. A delay can also be added to allow noise and vibration to settle.
  856. * These options are most useful for the BLTouch probe, but may also improve
  857. * readings with inductive probes and piezo sensors.
  858. */
  859. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  860. #if ENABLED(PROBING_HEATERS_OFF)
  861. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  862. #endif
  863. //#define PROBING_FANS_OFF // Turn fans off when probing
  864. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  865. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  866. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  867. // :{ 0:'Low', 1:'High' }
  868. #define X_ENABLE_ON 0
  869. #define Y_ENABLE_ON 0
  870. #define Z_ENABLE_ON 0
  871. #define E_ENABLE_ON 0 // For all extruders
  872. // Disables axis stepper immediately when it's not being used.
  873. // WARNING: When motors turn off there is a chance of losing position accuracy!
  874. #define DISABLE_X false
  875. #define DISABLE_Y false
  876. #define DISABLE_Z false
  877. // Warn on display about possibly reduced accuracy
  878. //#define DISABLE_REDUCED_ACCURACY_WARNING
  879. // @section extruder
  880. #define DISABLE_E false // For all extruders
  881. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  882. // @section machine
  883. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  884. #define INVERT_X_DIR false
  885. #define INVERT_Y_DIR true
  886. #define INVERT_Z_DIR false
  887. // @section extruder
  888. // For direct drive extruder v9 set to true, for geared extruder set to false.
  889. #define INVERT_E0_DIR false
  890. #define INVERT_E1_DIR false
  891. #define INVERT_E2_DIR false
  892. #define INVERT_E3_DIR false
  893. #define INVERT_E4_DIR false
  894. #define INVERT_E5_DIR false
  895. // @section homing
  896. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  897. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  898. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  899. // Be sure you have this distance over your Z_MAX_POS in case.
  900. // Direction of endstops when homing; 1=MAX, -1=MIN
  901. // :[-1,1]
  902. #define X_HOME_DIR -1
  903. #define Y_HOME_DIR -1
  904. #define Z_HOME_DIR -1
  905. // @section machine
  906. // The size of the print bed
  907. #define X_BED_SIZE 200
  908. #define Y_BED_SIZE 200
  909. // Travel limits (mm) after homing, corresponding to endstop positions.
  910. #define X_MIN_POS 0
  911. #define Y_MIN_POS 0
  912. #define Z_MIN_POS 0
  913. #define X_MAX_POS X_BED_SIZE
  914. #define Y_MAX_POS Y_BED_SIZE
  915. #define Z_MAX_POS 200
  916. /**
  917. * Software Endstops
  918. *
  919. * - Prevent moves outside the set machine bounds.
  920. * - Individual axes can be disabled, if desired.
  921. * - X and Y only apply to Cartesian robots.
  922. * - Use 'M211' to set software endstops on/off or report current state
  923. */
  924. // Min software endstops constrain movement within minimum coordinate bounds
  925. #define MIN_SOFTWARE_ENDSTOPS
  926. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  927. #define MIN_SOFTWARE_ENDSTOP_X
  928. #define MIN_SOFTWARE_ENDSTOP_Y
  929. #define MIN_SOFTWARE_ENDSTOP_Z
  930. #endif
  931. // Max software endstops constrain movement within maximum coordinate bounds
  932. #define MAX_SOFTWARE_ENDSTOPS
  933. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  934. #define MAX_SOFTWARE_ENDSTOP_X
  935. #define MAX_SOFTWARE_ENDSTOP_Y
  936. #define MAX_SOFTWARE_ENDSTOP_Z
  937. #endif
  938. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  939. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  940. #endif
  941. /**
  942. * Filament Runout Sensors
  943. * Mechanical or opto endstops are used to check for the presence of filament.
  944. *
  945. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  946. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  947. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  948. */
  949. //#define FILAMENT_RUNOUT_SENSOR
  950. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  951. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  952. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
  953. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  954. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  955. // Set one or more commands to execute on filament runout.
  956. // (After 'M412 H' Marlin will ask the host to handle the process.)
  957. #define FILAMENT_RUNOUT_SCRIPT "M600"
  958. // After a runout is detected, continue printing this length of filament
  959. // before executing the runout script. Useful for a sensor at the end of
  960. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  961. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  962. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  963. // Enable this option to use an encoder disc that toggles the runout pin
  964. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  965. // large enough to avoid false positives.)
  966. //#define FILAMENT_MOTION_SENSOR
  967. #endif
  968. #endif
  969. //===========================================================================
  970. //=============================== Bed Leveling ==============================
  971. //===========================================================================
  972. // @section calibrate
  973. /**
  974. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  975. * and behavior of G29 will change depending on your selection.
  976. *
  977. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  978. *
  979. * - AUTO_BED_LEVELING_3POINT
  980. * Probe 3 arbitrary points on the bed (that aren't collinear)
  981. * You specify the XY coordinates of all 3 points.
  982. * The result is a single tilted plane. Best for a flat bed.
  983. *
  984. * - AUTO_BED_LEVELING_LINEAR
  985. * Probe several points in a grid.
  986. * You specify the rectangle and the density of sample points.
  987. * The result is a single tilted plane. Best for a flat bed.
  988. *
  989. * - AUTO_BED_LEVELING_BILINEAR
  990. * Probe several points in a grid.
  991. * You specify the rectangle and the density of sample points.
  992. * The result is a mesh, best for large or uneven beds.
  993. *
  994. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  995. * A comprehensive bed leveling system combining the features and benefits
  996. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  997. * Validation and Mesh Editing systems.
  998. *
  999. * - MESH_BED_LEVELING
  1000. * Probe a grid manually
  1001. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1002. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1003. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1004. * With an LCD controller the process is guided step-by-step.
  1005. */
  1006. //#define AUTO_BED_LEVELING_3POINT
  1007. //#define AUTO_BED_LEVELING_LINEAR
  1008. //#define AUTO_BED_LEVELING_BILINEAR
  1009. //#define AUTO_BED_LEVELING_UBL
  1010. //#define MESH_BED_LEVELING
  1011. /**
  1012. * Normally G28 leaves leveling disabled on completion. Enable
  1013. * this option to have G28 restore the prior leveling state.
  1014. */
  1015. //#define RESTORE_LEVELING_AFTER_G28
  1016. /**
  1017. * Enable detailed logging of G28, G29, M48, etc.
  1018. * Turn on with the command 'M111 S32'.
  1019. * NOTE: Requires a lot of PROGMEM!
  1020. */
  1021. //#define DEBUG_LEVELING_FEATURE
  1022. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1023. // Gradually reduce leveling correction until a set height is reached,
  1024. // at which point movement will be level to the machine's XY plane.
  1025. // The height can be set with M420 Z<height>
  1026. #define ENABLE_LEVELING_FADE_HEIGHT
  1027. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1028. // split up moves into short segments like a Delta. This follows the
  1029. // contours of the bed more closely than edge-to-edge straight moves.
  1030. #define SEGMENT_LEVELED_MOVES
  1031. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1032. /**
  1033. * Enable the G26 Mesh Validation Pattern tool.
  1034. */
  1035. //#define G26_MESH_VALIDATION
  1036. #if ENABLED(G26_MESH_VALIDATION)
  1037. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1038. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1039. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1040. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1041. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1042. #endif
  1043. #endif
  1044. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1045. // Set the number of grid points per dimension.
  1046. #define GRID_MAX_POINTS_X 3
  1047. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1048. // Probe along the Y axis, advancing X after each column
  1049. //#define PROBE_Y_FIRST
  1050. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1051. // Beyond the probed grid, continue the implied tilt?
  1052. // Default is to maintain the height of the nearest edge.
  1053. //#define EXTRAPOLATE_BEYOND_GRID
  1054. //
  1055. // Experimental Subdivision of the grid by Catmull-Rom method.
  1056. // Synthesizes intermediate points to produce a more detailed mesh.
  1057. //
  1058. //#define ABL_BILINEAR_SUBDIVISION
  1059. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1060. // Number of subdivisions between probe points
  1061. #define BILINEAR_SUBDIVISIONS 3
  1062. #endif
  1063. #endif
  1064. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1065. //===========================================================================
  1066. //========================= Unified Bed Leveling ============================
  1067. //===========================================================================
  1068. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1069. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1070. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1071. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1072. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1073. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1074. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1075. // as the Z-Height correction value.
  1076. #elif ENABLED(MESH_BED_LEVELING)
  1077. //===========================================================================
  1078. //=================================== Mesh ==================================
  1079. //===========================================================================
  1080. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1081. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1082. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1083. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1084. #endif // BED_LEVELING
  1085. /**
  1086. * Add a bed leveling sub-menu for ABL or MBL.
  1087. * Include a guided procedure if manual probing is enabled.
  1088. */
  1089. //#define LCD_BED_LEVELING
  1090. #if ENABLED(LCD_BED_LEVELING)
  1091. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1092. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1093. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1094. #endif
  1095. // Add a menu item to move between bed corners for manual bed adjustment
  1096. //#define LEVEL_BED_CORNERS
  1097. #if ENABLED(LEVEL_BED_CORNERS)
  1098. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1099. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
  1100. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1101. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1102. #endif
  1103. /**
  1104. * Commands to execute at the end of G29 probing.
  1105. * Useful to retract or move the Z probe out of the way.
  1106. */
  1107. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1108. // @section homing
  1109. // The center of the bed is at (X=0, Y=0)
  1110. //#define BED_CENTER_AT_0_0
  1111. // Manually set the home position. Leave these undefined for automatic settings.
  1112. // For DELTA this is the top-center of the Cartesian print volume.
  1113. //#define MANUAL_X_HOME_POS 0
  1114. //#define MANUAL_Y_HOME_POS 0
  1115. //#define MANUAL_Z_HOME_POS 0
  1116. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1117. //
  1118. // With this feature enabled:
  1119. //
  1120. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1121. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1122. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1123. // - Prevent Z homing when the Z probe is outside bed area.
  1124. //
  1125. //#define Z_SAFE_HOMING
  1126. #if ENABLED(Z_SAFE_HOMING)
  1127. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1128. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1129. #endif
  1130. // Homing speeds (mm/m)
  1131. #define HOMING_FEEDRATE_XY (50*60)
  1132. #define HOMING_FEEDRATE_Z (4*60)
  1133. // Validate that endstops are triggered on homing moves
  1134. #define VALIDATE_HOMING_ENDSTOPS
  1135. // @section calibrate
  1136. /**
  1137. * Bed Skew Compensation
  1138. *
  1139. * This feature corrects for misalignment in the XYZ axes.
  1140. *
  1141. * Take the following steps to get the bed skew in the XY plane:
  1142. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1143. * 2. For XY_DIAG_AC measure the diagonal A to C
  1144. * 3. For XY_DIAG_BD measure the diagonal B to D
  1145. * 4. For XY_SIDE_AD measure the edge A to D
  1146. *
  1147. * Marlin automatically computes skew factors from these measurements.
  1148. * Skew factors may also be computed and set manually:
  1149. *
  1150. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1151. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1152. *
  1153. * If desired, follow the same procedure for XZ and YZ.
  1154. * Use these diagrams for reference:
  1155. *
  1156. * Y Z Z
  1157. * ^ B-------C ^ B-------C ^ B-------C
  1158. * | / / | / / | / /
  1159. * | / / | / / | / /
  1160. * | A-------D | A-------D | A-------D
  1161. * +-------------->X +-------------->X +-------------->Y
  1162. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1163. */
  1164. //#define SKEW_CORRECTION
  1165. #if ENABLED(SKEW_CORRECTION)
  1166. // Input all length measurements here:
  1167. #define XY_DIAG_AC 282.8427124746
  1168. #define XY_DIAG_BD 282.8427124746
  1169. #define XY_SIDE_AD 200
  1170. // Or, set the default skew factors directly here
  1171. // to override the above measurements:
  1172. #define XY_SKEW_FACTOR 0.0
  1173. //#define SKEW_CORRECTION_FOR_Z
  1174. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1175. #define XZ_DIAG_AC 282.8427124746
  1176. #define XZ_DIAG_BD 282.8427124746
  1177. #define YZ_DIAG_AC 282.8427124746
  1178. #define YZ_DIAG_BD 282.8427124746
  1179. #define YZ_SIDE_AD 200
  1180. #define XZ_SKEW_FACTOR 0.0
  1181. #define YZ_SKEW_FACTOR 0.0
  1182. #endif
  1183. // Enable this option for M852 to set skew at runtime
  1184. //#define SKEW_CORRECTION_GCODE
  1185. #endif
  1186. //=============================================================================
  1187. //============================= Additional Features ===========================
  1188. //=============================================================================
  1189. // @section extras
  1190. /**
  1191. * EEPROM
  1192. *
  1193. * Persistent storage to preserve configurable settings across reboots.
  1194. *
  1195. * M500 - Store settings to EEPROM.
  1196. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1197. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1198. */
  1199. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1200. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1201. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1202. #if ENABLED(EEPROM_SETTINGS)
  1203. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1204. #endif
  1205. //
  1206. // Host Keepalive
  1207. //
  1208. // When enabled Marlin will send a busy status message to the host
  1209. // every couple of seconds when it can't accept commands.
  1210. //
  1211. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1212. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1213. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1214. //
  1215. // M100 Free Memory Watcher
  1216. //
  1217. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1218. //
  1219. // G20/G21 Inch mode support
  1220. //
  1221. //#define INCH_MODE_SUPPORT
  1222. //
  1223. // M149 Set temperature units support
  1224. //
  1225. //#define TEMPERATURE_UNITS_SUPPORT
  1226. // @section temperature
  1227. // Preheat Constants
  1228. #define PREHEAT_1_LABEL "PLA"
  1229. #define PREHEAT_1_TEMP_HOTEND 180
  1230. #define PREHEAT_1_TEMP_BED 70
  1231. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1232. #define PREHEAT_2_LABEL "ABS"
  1233. #define PREHEAT_2_TEMP_HOTEND 240
  1234. #define PREHEAT_2_TEMP_BED 110
  1235. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1236. /**
  1237. * Nozzle Park
  1238. *
  1239. * Park the nozzle at the given XYZ position on idle or G27.
  1240. *
  1241. * The "P" parameter controls the action applied to the Z axis:
  1242. *
  1243. * P0 (Default) If Z is below park Z raise the nozzle.
  1244. * P1 Raise the nozzle always to Z-park height.
  1245. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1246. */
  1247. //#define NOZZLE_PARK_FEATURE
  1248. #if ENABLED(NOZZLE_PARK_FEATURE)
  1249. // Specify a park position as { X, Y, Z_raise }
  1250. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1251. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1252. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1253. #endif
  1254. /**
  1255. * Clean Nozzle Feature -- EXPERIMENTAL
  1256. *
  1257. * Adds the G12 command to perform a nozzle cleaning process.
  1258. *
  1259. * Parameters:
  1260. * P Pattern
  1261. * S Strokes / Repetitions
  1262. * T Triangles (P1 only)
  1263. *
  1264. * Patterns:
  1265. * P0 Straight line (default). This process requires a sponge type material
  1266. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1267. * between the start / end points.
  1268. *
  1269. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1270. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1271. * Zig-zags are done in whichever is the narrower dimension.
  1272. * For example, "G12 P1 S1 T3" will execute:
  1273. *
  1274. * --
  1275. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1276. * | | / \ / \ / \ |
  1277. * A | | / \ / \ / \ |
  1278. * | | / \ / \ / \ |
  1279. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1280. * -- +--------------------------------+
  1281. * |________|_________|_________|
  1282. * T1 T2 T3
  1283. *
  1284. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1285. * "R" specifies the radius. "S" specifies the stroke count.
  1286. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1287. *
  1288. * Caveats: The ending Z should be the same as starting Z.
  1289. * Attention: EXPERIMENTAL. G-code arguments may change.
  1290. *
  1291. */
  1292. //#define NOZZLE_CLEAN_FEATURE
  1293. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1294. // Default number of pattern repetitions
  1295. #define NOZZLE_CLEAN_STROKES 12
  1296. // Default number of triangles
  1297. #define NOZZLE_CLEAN_TRIANGLES 3
  1298. // Specify positions as { X, Y, Z }
  1299. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1) }
  1300. #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) }
  1301. // Circular pattern radius
  1302. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1303. // Circular pattern circle fragments number
  1304. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1305. // Middle point of circle
  1306. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1307. // Move the nozzle to the initial position after cleaning
  1308. #define NOZZLE_CLEAN_GOBACK
  1309. // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
  1310. //#define NOZZLE_CLEAN_NO_Z
  1311. #endif
  1312. /**
  1313. * Print Job Timer
  1314. *
  1315. * Automatically start and stop the print job timer on M104/M109/M190.
  1316. *
  1317. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1318. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1319. * M190 (bed, wait) - high temp = start timer, low temp = none
  1320. *
  1321. * The timer can also be controlled with the following commands:
  1322. *
  1323. * M75 - Start the print job timer
  1324. * M76 - Pause the print job timer
  1325. * M77 - Stop the print job timer
  1326. */
  1327. #define PRINTJOB_TIMER_AUTOSTART
  1328. /**
  1329. * Print Counter
  1330. *
  1331. * Track statistical data such as:
  1332. *
  1333. * - Total print jobs
  1334. * - Total successful print jobs
  1335. * - Total failed print jobs
  1336. * - Total time printing
  1337. *
  1338. * View the current statistics with M78.
  1339. */
  1340. //#define PRINTCOUNTER
  1341. //=============================================================================
  1342. //============================= LCD and SD support ============================
  1343. //=============================================================================
  1344. // @section lcd
  1345. /**
  1346. * LCD LANGUAGE
  1347. *
  1348. * Select the language to display on the LCD. These languages are available:
  1349. *
  1350. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
  1351. * ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1352. *
  1353. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1354. */
  1355. #define LCD_LANGUAGE en
  1356. /**
  1357. * LCD Character Set
  1358. *
  1359. * Note: This option is NOT applicable to Graphical Displays.
  1360. *
  1361. * All character-based LCDs provide ASCII plus one of these
  1362. * language extensions:
  1363. *
  1364. * - JAPANESE ... the most common
  1365. * - WESTERN ... with more accented characters
  1366. * - CYRILLIC ... for the Russian language
  1367. *
  1368. * To determine the language extension installed on your controller:
  1369. *
  1370. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1371. * - Click the controller to view the LCD menu
  1372. * - The LCD will display Japanese, Western, or Cyrillic text
  1373. *
  1374. * See http://marlinfw.org/docs/development/lcd_language.html
  1375. *
  1376. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1377. */
  1378. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1379. /**
  1380. * Info Screen Style (0:Classic, 1:Prusa)
  1381. *
  1382. * :[0:'Classic', 1:'Prusa']
  1383. */
  1384. #define LCD_INFO_SCREEN_STYLE 0
  1385. /**
  1386. * SD CARD
  1387. *
  1388. * SD Card support is disabled by default. If your controller has an SD slot,
  1389. * you must uncomment the following option or it won't work.
  1390. *
  1391. */
  1392. //#define SDSUPPORT
  1393. /**
  1394. * SD CARD: SPI SPEED
  1395. *
  1396. * Enable one of the following items for a slower SPI transfer speed.
  1397. * This may be required to resolve "volume init" errors.
  1398. */
  1399. //#define SPI_SPEED SPI_HALF_SPEED
  1400. //#define SPI_SPEED SPI_QUARTER_SPEED
  1401. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1402. /**
  1403. * SD CARD: ENABLE CRC
  1404. *
  1405. * Use CRC checks and retries on the SD communication.
  1406. */
  1407. //#define SD_CHECK_AND_RETRY
  1408. /**
  1409. * LCD Menu Items
  1410. *
  1411. * Disable all menus and only display the Status Screen, or
  1412. * just remove some extraneous menu items to recover space.
  1413. */
  1414. //#define NO_LCD_MENUS
  1415. //#define SLIM_LCD_MENUS
  1416. //
  1417. // ENCODER SETTINGS
  1418. //
  1419. // This option overrides the default number of encoder pulses needed to
  1420. // produce one step. Should be increased for high-resolution encoders.
  1421. //
  1422. //#define ENCODER_PULSES_PER_STEP 4
  1423. //
  1424. // Use this option to override the number of step signals required to
  1425. // move between next/prev menu items.
  1426. //
  1427. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1428. /**
  1429. * Encoder Direction Options
  1430. *
  1431. * Test your encoder's behavior first with both options disabled.
  1432. *
  1433. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1434. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1435. * Reversed Value Editing only? Enable BOTH options.
  1436. */
  1437. //
  1438. // This option reverses the encoder direction everywhere.
  1439. //
  1440. // Set this option if CLOCKWISE causes values to DECREASE
  1441. //
  1442. //#define REVERSE_ENCODER_DIRECTION
  1443. //
  1444. // This option reverses the encoder direction for navigating LCD menus.
  1445. //
  1446. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1447. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1448. //
  1449. //#define REVERSE_MENU_DIRECTION
  1450. //
  1451. // This option reverses the encoder direction for Select Screen.
  1452. //
  1453. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1454. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1455. //
  1456. //#define REVERSE_SELECT_DIRECTION
  1457. //
  1458. // Individual Axis Homing
  1459. //
  1460. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1461. //
  1462. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1463. //
  1464. // SPEAKER/BUZZER
  1465. //
  1466. // If you have a speaker that can produce tones, enable it here.
  1467. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1468. //
  1469. //#define SPEAKER
  1470. //
  1471. // The duration and frequency for the UI feedback sound.
  1472. // Set these to 0 to disable audio feedback in the LCD menus.
  1473. //
  1474. // Note: Test audio output with the G-Code:
  1475. // M300 S<frequency Hz> P<duration ms>
  1476. //
  1477. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1478. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1479. //=============================================================================
  1480. //======================== LCD / Controller Selection =========================
  1481. //======================== (Character-based LCDs) =========================
  1482. //=============================================================================
  1483. //
  1484. // RepRapDiscount Smart Controller.
  1485. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1486. //
  1487. // Note: Usually sold with a white PCB.
  1488. //
  1489. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1490. //
  1491. // Original RADDS LCD Display+Encoder+SDCardReader
  1492. // http://doku.radds.org/dokumentation/lcd-display/
  1493. //
  1494. //#define RADDS_DISPLAY
  1495. //
  1496. // ULTIMAKER Controller.
  1497. //
  1498. //#define ULTIMAKERCONTROLLER
  1499. //
  1500. // ULTIPANEL as seen on Thingiverse.
  1501. //
  1502. //#define ULTIPANEL
  1503. //
  1504. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1505. // http://reprap.org/wiki/PanelOne
  1506. //
  1507. //#define PANEL_ONE
  1508. //
  1509. // GADGETS3D G3D LCD/SD Controller
  1510. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1511. //
  1512. // Note: Usually sold with a blue PCB.
  1513. //
  1514. //#define G3D_PANEL
  1515. //
  1516. // RigidBot Panel V1.0
  1517. // http://www.inventapart.com/
  1518. //
  1519. //#define RIGIDBOT_PANEL
  1520. //
  1521. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1522. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1523. //
  1524. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1525. //
  1526. // ANET and Tronxy 20x4 Controller
  1527. //
  1528. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1529. // This LCD is known to be susceptible to electrical interference
  1530. // which scrambles the display. Pressing any button clears it up.
  1531. // This is a LCD2004 display with 5 analog buttons.
  1532. //
  1533. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1534. //
  1535. //#define ULTRA_LCD
  1536. //=============================================================================
  1537. //======================== LCD / Controller Selection =========================
  1538. //===================== (I2C and Shift-Register LCDs) =====================
  1539. //=============================================================================
  1540. //
  1541. // CONTROLLER TYPE: I2C
  1542. //
  1543. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1544. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1545. //
  1546. //
  1547. // Elefu RA Board Control Panel
  1548. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1549. //
  1550. //#define RA_CONTROL_PANEL
  1551. //
  1552. // Sainsmart (YwRobot) LCD Displays
  1553. //
  1554. // These require F.Malpartida's LiquidCrystal_I2C library
  1555. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1556. //
  1557. //#define LCD_SAINSMART_I2C_1602
  1558. //#define LCD_SAINSMART_I2C_2004
  1559. //
  1560. // Generic LCM1602 LCD adapter
  1561. //
  1562. //#define LCM1602
  1563. //
  1564. // PANELOLU2 LCD with status LEDs,
  1565. // separate encoder and click inputs.
  1566. //
  1567. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1568. // For more info: https://github.com/lincomatic/LiquidTWI2
  1569. //
  1570. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1571. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1572. //
  1573. //#define LCD_I2C_PANELOLU2
  1574. //
  1575. // Panucatt VIKI LCD with status LEDs,
  1576. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1577. //
  1578. //#define LCD_I2C_VIKI
  1579. //
  1580. // CONTROLLER TYPE: Shift register panels
  1581. //
  1582. //
  1583. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1584. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1585. //
  1586. //#define SAV_3DLCD
  1587. //
  1588. // 3-wire SR LCD with strobe using 74HC4094
  1589. // https://github.com/mikeshub/SailfishLCD
  1590. // Uses the code directly from Sailfish
  1591. //
  1592. //#define FF_INTERFACEBOARD
  1593. //=============================================================================
  1594. //======================= LCD / Controller Selection =======================
  1595. //========================= (Graphical LCDs) ========================
  1596. //=============================================================================
  1597. //
  1598. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1599. //
  1600. // IMPORTANT: The U8glib library is required for Graphical Display!
  1601. // https://github.com/olikraus/U8glib_Arduino
  1602. //
  1603. //
  1604. // RepRapDiscount FULL GRAPHIC Smart Controller
  1605. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1606. //
  1607. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1608. //
  1609. // ReprapWorld Graphical LCD
  1610. // https://reprapworld.com/?products_details&products_id/1218
  1611. //
  1612. //#define REPRAPWORLD_GRAPHICAL_LCD
  1613. //
  1614. // Activate one of these if you have a Panucatt Devices
  1615. // Viki 2.0 or mini Viki with Graphic LCD
  1616. // http://panucatt.com
  1617. //
  1618. //#define VIKI2
  1619. //#define miniVIKI
  1620. //
  1621. // MakerLab Mini Panel with graphic
  1622. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1623. //
  1624. //#define MINIPANEL
  1625. //
  1626. // MaKr3d Makr-Panel with graphic controller and SD support.
  1627. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1628. //
  1629. //#define MAKRPANEL
  1630. //
  1631. // Adafruit ST7565 Full Graphic Controller.
  1632. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1633. //
  1634. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1635. //
  1636. // BQ LCD Smart Controller shipped by
  1637. // default with the BQ Hephestos 2 and Witbox 2.
  1638. //
  1639. //#define BQ_LCD_SMART_CONTROLLER
  1640. //
  1641. // Cartesio UI
  1642. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1643. //
  1644. //#define CARTESIO_UI
  1645. //
  1646. // LCD for Melzi Card with Graphical LCD
  1647. //
  1648. //#define LCD_FOR_MELZI
  1649. //
  1650. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1651. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1652. //
  1653. //#define ULTI_CONTROLLER
  1654. //
  1655. // MKS MINI12864 with graphic controller and SD support
  1656. // https://reprap.org/wiki/MKS_MINI_12864
  1657. //
  1658. //#define MKS_MINI_12864
  1659. //
  1660. // FYSETC variant of the MINI12864 graphic controller with SD support
  1661. // https://wiki.fysetc.com/Mini12864_Panel/
  1662. //
  1663. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1664. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1665. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1666. //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight
  1667. //
  1668. // Factory display for Creality CR-10
  1669. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1670. //
  1671. // This is RAMPS-compatible using a single 10-pin connector.
  1672. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1673. //
  1674. //#define CR10_STOCKDISPLAY
  1675. //
  1676. // ANET and Tronxy Graphical Controller
  1677. //
  1678. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1679. // A clone of the RepRapDiscount full graphics display but with
  1680. // different pins/wiring (see pins_ANET_10.h).
  1681. //
  1682. //#define ANET_FULL_GRAPHICS_LCD
  1683. //
  1684. // AZSMZ 12864 LCD with SD
  1685. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1686. //
  1687. //#define AZSMZ_12864
  1688. //
  1689. // Silvergate GLCD controller
  1690. // http://github.com/android444/Silvergate
  1691. //
  1692. //#define SILVER_GATE_GLCD_CONTROLLER
  1693. //=============================================================================
  1694. //============================== OLED Displays ==============================
  1695. //=============================================================================
  1696. //
  1697. // SSD1306 OLED full graphics generic display
  1698. //
  1699. //#define U8GLIB_SSD1306
  1700. //
  1701. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1702. //
  1703. //#define SAV_3DGLCD
  1704. #if ENABLED(SAV_3DGLCD)
  1705. #define U8GLIB_SSD1306
  1706. //#define U8GLIB_SH1106
  1707. #endif
  1708. //
  1709. // TinyBoy2 128x64 OLED / Encoder Panel
  1710. //
  1711. //#define OLED_PANEL_TINYBOY2
  1712. //
  1713. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1714. // http://reprap.org/wiki/MKS_12864OLED
  1715. //
  1716. // Tiny, but very sharp OLED display
  1717. //
  1718. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1719. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1720. //
  1721. // Einstart S OLED SSD1306
  1722. //
  1723. //#define U8GLIB_SH1106_EINSTART
  1724. //
  1725. // Overlord OLED display/controller with i2c buzzer and LEDs
  1726. //
  1727. //#define OVERLORD_OLED
  1728. //=============================================================================
  1729. //========================== Extensible UI Displays ===========================
  1730. //=============================================================================
  1731. //
  1732. // DGUS Touch Display with DWIN OS
  1733. //
  1734. //#define DGUS_LCD
  1735. //
  1736. // Touch-screen LCD for Malyan M200 printers
  1737. //
  1738. //#define MALYAN_LCD
  1739. //
  1740. // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
  1741. // See Configuration_adv.h for all configuration options.
  1742. //
  1743. //#define LULZBOT_TOUCH_UI
  1744. //
  1745. // Third-party or vendor-customized controller interfaces.
  1746. // Sources should be installed in 'src/lcd/extensible_ui'.
  1747. //
  1748. //#define EXTENSIBLE_UI
  1749. //=============================================================================
  1750. //=============================== Graphical TFTs ==============================
  1751. //=============================================================================
  1752. //
  1753. // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
  1754. //
  1755. //#define FSMC_GRAPHICAL_TFT
  1756. //=============================================================================
  1757. //============================ Other Controllers ============================
  1758. //=============================================================================
  1759. //
  1760. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  1761. //
  1762. //#define TOUCH_BUTTONS
  1763. #if ENABLED(TOUCH_BUTTONS)
  1764. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  1765. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  1766. #define XPT2046_X_CALIBRATION 12316
  1767. #define XPT2046_Y_CALIBRATION -8981
  1768. #define XPT2046_X_OFFSET -43
  1769. #define XPT2046_Y_OFFSET 257
  1770. #endif
  1771. //
  1772. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1773. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1774. //
  1775. //#define REPRAPWORLD_KEYPAD
  1776. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  1777. //=============================================================================
  1778. //=============================== Extra Features ==============================
  1779. //=============================================================================
  1780. // @section extras
  1781. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1782. //#define FAST_PWM_FAN
  1783. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1784. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1785. // is too low, you should also increment SOFT_PWM_SCALE.
  1786. //#define FAN_SOFT_PWM
  1787. // Incrementing this by 1 will double the software PWM frequency,
  1788. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1789. // However, control resolution will be halved for each increment;
  1790. // at zero value, there are 128 effective control positions.
  1791. // :[0,1,2,3,4,5,6,7]
  1792. #define SOFT_PWM_SCALE 0
  1793. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1794. // be used to mitigate the associated resolution loss. If enabled,
  1795. // some of the PWM cycles are stretched so on average the desired
  1796. // duty cycle is attained.
  1797. //#define SOFT_PWM_DITHER
  1798. // Temperature status LEDs that display the hotend and bed temperature.
  1799. // If all hotends, bed temperature, and target temperature are under 54C
  1800. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1801. //#define TEMP_STAT_LEDS
  1802. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1803. //#define SF_ARC_FIX
  1804. // Support for the BariCUDA Paste Extruder
  1805. //#define BARICUDA
  1806. // Support for BlinkM/CyzRgb
  1807. //#define BLINKM
  1808. // Support for PCA9632 PWM LED driver
  1809. //#define PCA9632
  1810. // Support for PCA9533 PWM LED driver
  1811. // https://github.com/mikeshub/SailfishRGB_LED
  1812. //#define PCA9533
  1813. /**
  1814. * RGB LED / LED Strip Control
  1815. *
  1816. * Enable support for an RGB LED connected to 5V digital pins, or
  1817. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1818. *
  1819. * Adds the M150 command to set the LED (or LED strip) color.
  1820. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1821. * luminance values can be set from 0 to 255.
  1822. * For Neopixel LED an overall brightness parameter is also available.
  1823. *
  1824. * *** CAUTION ***
  1825. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1826. * as the Arduino cannot handle the current the LEDs will require.
  1827. * Failure to follow this precaution can destroy your Arduino!
  1828. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1829. * more current than the Arduino 5V linear regulator can produce.
  1830. * *** CAUTION ***
  1831. *
  1832. * LED Type. Enable only one of the following two options.
  1833. *
  1834. */
  1835. //#define RGB_LED
  1836. //#define RGBW_LED
  1837. #if EITHER(RGB_LED, RGBW_LED)
  1838. //#define RGB_LED_R_PIN 34
  1839. //#define RGB_LED_G_PIN 43
  1840. //#define RGB_LED_B_PIN 35
  1841. //#define RGB_LED_W_PIN -1
  1842. #endif
  1843. // Support for Adafruit Neopixel LED driver
  1844. //#define NEOPIXEL_LED
  1845. #if ENABLED(NEOPIXEL_LED)
  1846. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1847. #define NEOPIXEL_PIN 4 // LED driving pin
  1848. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  1849. //#define NEOPIXEL2_PIN 5
  1850. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
  1851. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1852. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1853. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1854. // Use a single Neopixel LED for static (background) lighting
  1855. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  1856. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  1857. #endif
  1858. /**
  1859. * Printer Event LEDs
  1860. *
  1861. * During printing, the LEDs will reflect the printer status:
  1862. *
  1863. * - Gradually change from blue to violet as the heated bed gets to target temp
  1864. * - Gradually change from violet to red as the hotend gets to temperature
  1865. * - Change to white to illuminate work surface
  1866. * - Change to green once print has finished
  1867. * - Turn off after the print has finished and the user has pushed a button
  1868. */
  1869. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  1870. #define PRINTER_EVENT_LEDS
  1871. #endif
  1872. /**
  1873. * R/C SERVO support
  1874. * Sponsored by TrinityLabs, Reworked by codexmas
  1875. */
  1876. /**
  1877. * Number of servos
  1878. *
  1879. * For some servo-related options NUM_SERVOS will be set automatically.
  1880. * Set this manually if there are extra servos needing manual control.
  1881. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1882. */
  1883. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1884. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  1885. // 300ms is a good value but you can try less delay.
  1886. // If the servo can't reach the requested position, increase it.
  1887. #define SERVO_DELAY { 300 }
  1888. // Only power servos during movement, otherwise leave off to prevent jitter
  1889. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1890. // Allow servo angle to be edited and saved to EEPROM
  1891. //#define EDITABLE_SERVO_ANGLES