My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Вы не можете выбрать более 25 тем Темы должны начинаться с буквы или цифры, могут содержать дефисы(-) и должны содержать не более 35 символов.

Configuration.h 79KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098109911001101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125112611271128112911301131113211331134113511361137113811391140114111421143114411451146114711481149115011511152115311541155115611571158115911601161116211631164116511661167116811691170117111721173117411751176117711781179118011811182118311841185118611871188118911901191119211931194119511961197119811991200120112021203120412051206120712081209121012111212121312141215121612171218121912201221122212231224122512261227122812291230123112321233123412351236123712381239124012411242124312441245124612471248124912501251125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275127612771278127912801281128212831284128512861287128812891290129112921293129412951296129712981299130013011302130313041305130613071308130913101311131213131314131513161317131813191320132113221323132413251326132713281329133013311332133313341335133613371338133913401341134213431344134513461347134813491350135113521353135413551356135713581359136013611362136313641365136613671368136913701371137213731374137513761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410141114121413141414151416141714181419142014211422142314241425142614271428142914301431143214331434143514361437143814391440144114421443144414451446144714481449145014511452145314541455145614571458145914601461146214631464146514661467146814691470147114721473147414751476147714781479148014811482148314841485148614871488148914901491149214931494149514961497149814991500150115021503150415051506150715081509151015111512151315141515151615171518151915201521152215231524152515261527152815291530153115321533153415351536153715381539154015411542154315441545154615471548154915501551155215531554155515561557155815591560156115621563156415651566156715681569157015711572157315741575157615771578157915801581158215831584158515861587158815891590159115921593159415951596159715981599160016011602160316041605160616071608160916101611161216131614161516161617161816191620162116221623162416251626162716281629163016311632163316341635163616371638163916401641164216431644164516461647164816491650165116521653165416551656165716581659166016611662166316641665166616671668166916701671167216731674167516761677167816791680168116821683168416851686168716881689169016911692169316941695169616971698169917001701170217031704170517061707170817091710171117121713171417151716171717181719172017211722172317241725172617271728172917301731173217331734173517361737173817391740174117421743174417451746174717481749175017511752175317541755175617571758175917601761176217631764176517661767176817691770177117721773177417751776177717781779178017811782178317841785178617871788178917901791179217931794179517961797179817991800180118021803180418051806180718081809181018111812181318141815181618171818181918201821182218231824182518261827182818291830183118321833183418351836183718381839184018411842184318441845184618471848184918501851185218531854185518561857185818591860186118621863186418651866186718681869187018711872187318741875187618771878187918801881188218831884188518861887188818891890189118921893189418951896189718981899190019011902190319041905190619071908190919101911191219131914191519161917191819191920192119221923192419251926192719281929193019311932193319341935193619371938193919401941194219431944194519461947194819491950195119521953195419551956195719581959196019611962196319641965196619671968196919701971197219731974197519761977197819791980198119821983198419851986198719881989199019911992199319941995199619971998199920002001200220032004200520062007200820092010201120122013201420152016201720182019202020212022202320242025202620272028202920302031203220332034203520362037203820392040204120422043204420452046204720482049205020512052205320542055205620572058205920602061206220632064206520662067206820692070207120722073207420752076207720782079208020812082208320842085208620872088208920902091209220932094209520962097209820992100210121022103210421052106210721082109211021112112211321142115211621172118211921202121212221232124212521262127212821292130213121322133213421352136213721382139214021412142214321442145214621472148214921502151215221532154215521562157215821592160216121622163216421652166216721682169217021712172217321742175217621772178217921802181218221832184218521862187218821892190219121922193219421952196219721982199220022012202220322042205220622072208
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #define CONFIGURATION_H_VERSION 020000
  39. //===========================================================================
  40. //============================= Getting Started =============================
  41. //===========================================================================
  42. /**
  43. * Here are some standard links for getting your machine calibrated:
  44. *
  45. * http://reprap.org/wiki/Calibration
  46. * http://youtu.be/wAL9d7FgInk
  47. * http://calculator.josefprusa.cz
  48. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  49. * http://www.thingiverse.com/thing:5573
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * http://www.thingiverse.com/thing:298812
  52. */
  53. //===========================================================================
  54. //============================= DELTA Printer ===============================
  55. //===========================================================================
  56. // For a Delta printer start with one of the configuration files in the
  57. // config/examples/delta directory and customize for your machine.
  58. //
  59. //===========================================================================
  60. //============================= SCARA Printer ===============================
  61. //===========================================================================
  62. // For a SCARA printer start with the configuration files in
  63. // config/examples/SCARA and customize for your machine.
  64. //
  65. // @section info
  66. // Author info of this build printed to the host during boot and M115
  67. #define STRING_CONFIG_H_AUTHOR "(MaukCC, CartesioE)" // Who made the changes.
  68. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  69. /**
  70. * *** VENDORS PLEASE READ ***
  71. *
  72. * Marlin allows you to add a custom boot image for Graphical LCDs.
  73. * With this option Marlin will first show your custom screen followed
  74. * by the standard Marlin logo with version number and web URL.
  75. *
  76. * We encourage you to take advantage of this new feature and we also
  77. * respectfully request that you retain the unmodified Marlin boot screen.
  78. */
  79. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  80. #define SHOW_BOOTSCREEN
  81. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  82. #define SHOW_CUSTOM_BOOTSCREEN
  83. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  84. //#define CUSTOM_STATUS_SCREEN_IMAGE
  85. // @section machine
  86. /**
  87. * Select the serial port on the board to use for communication with the host.
  88. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT 0
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  97. * Serial port -1 is the USB emulated serial port, if available.
  98. *
  99. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  100. */
  101. //#define SERIAL_PORT_2 -1
  102. /**
  103. * This setting determines the communication speed of the printer.
  104. *
  105. * 250000 works in most cases, but you might try a lower speed if
  106. * you commonly experience drop-outs during host printing.
  107. * You may try up to 1000000 to speed up SD file transfer.
  108. *
  109. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  110. */
  111. #define BAUDRATE 115200
  112. // Enable the Bluetooth serial interface on AT90USB devices
  113. //#define BLUETOOTH
  114. // Choose the name from boards.h that matches your setup
  115. #ifndef MOTHERBOARD
  116. //#define MOTHERBOARD BOARD_CNCONTROLS_11
  117. #define MOTHERBOARD BOARD_CNCONTROLS_12
  118. #endif
  119. // Name displayed in the LCD "Ready" message and Info menu
  120. #define CUSTOM_MACHINE_NAME "CartesioE"
  121. // Printer's unique ID, used by some programs to differentiate between machines.
  122. // Choose your own or use a service like http://www.uuidgenerator.net/version4
  123. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  124. // @section extruder
  125. // This defines the number of extruders
  126. // :[1, 2, 3, 4, 5, 6]
  127. #define EXTRUDERS 3
  128. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  129. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
  130. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  131. //#define SINGLENOZZLE
  132. /**
  133. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  134. *
  135. * This device allows one stepper driver on a control board to drive
  136. * two to eight stepper motors, one at a time, in a manner suitable
  137. * for extruders.
  138. *
  139. * This option only allows the multiplexer to switch on tool-change.
  140. * Additional options to configure custom E moves are pending.
  141. */
  142. //#define MK2_MULTIPLEXER
  143. #if ENABLED(MK2_MULTIPLEXER)
  144. // Override the default DIO selector pins here, if needed.
  145. // Some pins files may provide defaults for these pins.
  146. //#define E_MUX0_PIN 40 // Always Required
  147. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  148. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  149. #endif
  150. /**
  151. * Prusa Multi-Material Unit v2
  152. *
  153. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  154. * Requires EXTRUDERS = 5
  155. *
  156. * For additional configuration see Configuration_adv.h
  157. */
  158. //#define PRUSA_MMU2
  159. // A dual extruder that uses a single stepper motor
  160. //#define SWITCHING_EXTRUDER
  161. #if ENABLED(SWITCHING_EXTRUDER)
  162. #define SWITCHING_EXTRUDER_SERVO_NR 0
  163. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  164. #if EXTRUDERS > 3
  165. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  166. #endif
  167. #endif
  168. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  169. //#define SWITCHING_NOZZLE
  170. #if ENABLED(SWITCHING_NOZZLE)
  171. #define SWITCHING_NOZZLE_SERVO_NR 0
  172. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  173. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  174. #endif
  175. /**
  176. * Two separate X-carriages with extruders that connect to a moving part
  177. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  178. */
  179. //#define PARKING_EXTRUDER
  180. /**
  181. * Two separate X-carriages with extruders that connect to a moving part
  182. * via a magnetic docking mechanism using movements and no solenoid
  183. *
  184. * project : https://www.thingiverse.com/thing:3080893
  185. * movements : https://youtu.be/0xCEiG9VS3k
  186. * https://youtu.be/Bqbcs0CU2FE
  187. */
  188. //#define MAGNETIC_PARKING_EXTRUDER
  189. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  190. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  191. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  192. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  193. #if ENABLED(PARKING_EXTRUDER)
  194. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  195. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  196. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  197. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  198. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  199. #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
  200. #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
  201. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  202. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  203. #endif
  204. #endif
  205. /**
  206. * Switching Toolhead
  207. *
  208. * Support for swappable and dockable toolheads, such as
  209. * the E3D Tool Changer. Toolheads are locked with a servo.
  210. */
  211. //#define SWITCHING_TOOLHEAD
  212. /**
  213. * Magnetic Switching Toolhead
  214. *
  215. * Support swappable and dockable toolheads with a magnetic
  216. * docking mechanism using movement and no servo.
  217. */
  218. //#define MAGNETIC_SWITCHING_TOOLHEAD
  219. /**
  220. * Electromagnetic Switching Toolhead
  221. *
  222. * Parking for CoreXY / HBot kinematics.
  223. * Toolheads are parked at one edge and held with an electromagnet.
  224. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  225. */
  226. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  227. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  228. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  229. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  230. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  231. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  232. #if ENABLED(SWITCHING_TOOLHEAD)
  233. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  234. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  235. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  236. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  237. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  238. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  239. #if ENABLED(PRIME_BEFORE_REMOVE)
  240. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  241. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  242. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate
  243. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate
  244. #endif
  245. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  246. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  247. #endif
  248. #endif
  249. /**
  250. * "Mixing Extruder"
  251. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  252. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  253. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  254. * - This implementation supports up to two mixing extruders.
  255. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  256. */
  257. //#define MIXING_EXTRUDER
  258. #if ENABLED(MIXING_EXTRUDER)
  259. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  260. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  261. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  262. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  263. #if ENABLED(GRADIENT_MIX)
  264. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  265. #endif
  266. #endif
  267. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  268. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  269. // For the other hotends it is their distance from the extruder 0 hotend.
  270. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  271. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  272. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  273. // @section machine
  274. /**
  275. * Power Supply Control
  276. *
  277. * Enable and connect the power supply to the PS_ON_PIN.
  278. * Specify whether the power supply is active HIGH or active LOW.
  279. */
  280. #define PSU_CONTROL
  281. //#define PSU_NAME "Power Supply"
  282. #if ENABLED(PSU_CONTROL)
  283. #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
  284. //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80
  285. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  286. #if ENABLED(AUTO_POWER_CONTROL)
  287. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  288. #define AUTO_POWER_E_FANS
  289. #define AUTO_POWER_CONTROLLERFAN
  290. #define AUTO_POWER_CHAMBER_FAN
  291. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature
  292. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature
  293. #define POWER_TIMEOUT 30
  294. #endif
  295. #endif
  296. // @section temperature
  297. //===========================================================================
  298. //============================= Thermal Settings ============================
  299. //===========================================================================
  300. /**
  301. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  302. *
  303. * Temperature sensors available:
  304. *
  305. * -4 : thermocouple with AD8495
  306. * -3 : thermocouple with MAX31855 (only for sensor 0)
  307. * -2 : thermocouple with MAX6675 (only for sensor 0)
  308. * -1 : thermocouple with AD595
  309. * 0 : not used
  310. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  311. * 331 : (3.3V scaled thermistor 1 table)
  312. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  313. * 3 : Mendel-parts thermistor (4.7k pullup)
  314. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  315. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  316. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  317. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  318. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  319. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  320. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  321. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  322. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  323. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  324. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  325. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  326. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  327. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  328. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  329. * 20 : Pt100 with circuit in the Ultimainboard V2.x
  330. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  331. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  332. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  333. * 66 : 4.7M High Temperature thermistor from Dyze Design
  334. * 67 : 450C thermistor from SliceEngineering
  335. * 70 : the 100K thermistor found in the bq Hephestos 2
  336. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  337. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  338. *
  339. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  340. * (but gives greater accuracy and more stable PID)
  341. * 51 : 100k thermistor - EPCOS (1k pullup)
  342. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  343. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  344. *
  345. * 1047 : Pt1000 with 4k7 pullup
  346. * 1010 : Pt1000 with 1k pullup (non standard)
  347. * 147 : Pt100 with 4k7 pullup
  348. * 110 : Pt100 with 1k pullup (non standard)
  349. *
  350. * 1000 : Custom - Specify parameters in Configuration_adv.h
  351. *
  352. * Use these for Testing or Development purposes. NEVER for production machine.
  353. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  354. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  355. */
  356. #define TEMP_SENSOR_0 -1
  357. #define TEMP_SENSOR_1 -1
  358. #define TEMP_SENSOR_2 1
  359. #define TEMP_SENSOR_3 0
  360. #define TEMP_SENSOR_4 0
  361. #define TEMP_SENSOR_5 0
  362. #define TEMP_SENSOR_BED 1
  363. #define TEMP_SENSOR_CHAMBER 0
  364. // Dummy thermistor constant temperature readings, for use with 998 and 999
  365. #define DUMMY_THERMISTOR_998_VALUE 25
  366. #define DUMMY_THERMISTOR_999_VALUE 100
  367. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  368. // from the two sensors differ too much the print will be aborted.
  369. //#define TEMP_SENSOR_1_AS_REDUNDANT
  370. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  371. #define TEMP_RESIDENCY_TIME 4 // (seconds) Time to wait for hotend to "settle" in M109
  372. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  373. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  374. #define TEMP_BED_RESIDENCY_TIME 1 // (seconds) Time to wait for bed to "settle" in M190
  375. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  376. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  377. // Below this temperature the heater will be switched off
  378. // because it probably indicates a broken thermistor wire.
  379. #define HEATER_0_MINTEMP 5
  380. #define HEATER_1_MINTEMP 5
  381. #define HEATER_2_MINTEMP 5
  382. #define HEATER_3_MINTEMP 5
  383. #define HEATER_4_MINTEMP 5
  384. #define HEATER_5_MINTEMP 5
  385. #define BED_MINTEMP 5
  386. // Above this temperature the heater will be switched off.
  387. // This can protect components from overheating, but NOT from shorts and failures.
  388. // (Use MINTEMP for thermistor short/failure protection.)
  389. #define HEATER_0_MAXTEMP 415
  390. #define HEATER_1_MAXTEMP 415
  391. #define HEATER_2_MAXTEMP 415
  392. #define HEATER_3_MAXTEMP 415
  393. #define HEATER_4_MAXTEMP 415
  394. #define HEATER_5_MAXTEMP 415
  395. #define BED_MAXTEMP 165
  396. //===========================================================================
  397. //============================= PID Settings ================================
  398. //===========================================================================
  399. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  400. // Comment the following line to disable PID and enable bang-bang.
  401. #define PIDTEMP
  402. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  403. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  404. #define PID_K1 0.95 // Smoothing factor within any PID loop
  405. #if ENABLED(PIDTEMP)
  406. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  407. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  408. //#define PID_DEBUG // Sends debug data to the serial port.
  409. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  410. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  411. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  412. // Set/get with gcode: M301 E[extruder number, 0-2]
  413. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  414. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  415. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  416. // Cartesio extruderV6 40W Normal
  417. #define DEFAULT_Kp 18
  418. #define DEFAULT_Ki 1
  419. #define DEFAULT_Kd 100
  420. // Cartesio extruderV6 40W Volcano
  421. //#define DEFAULT_Kp 50
  422. //#define DEFAULT_Ki 9
  423. //#define DEFAULT_Kd 70
  424. // Cartesio extruderV6 40W Cyclops
  425. //#define DEFAULT_Kp 18
  426. //#define DEFAULT_Ki 1
  427. //#define DEFAULT_Kd 100
  428. #endif // PIDTEMP
  429. //===========================================================================
  430. //====================== PID > Bed Temperature Control ======================
  431. //===========================================================================
  432. /**
  433. * PID Bed Heating
  434. *
  435. * If this option is enabled set PID constants below.
  436. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  437. *
  438. * The PID frequency will be the same as the extruder PWM.
  439. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  440. * which is fine for driving a square wave into a resistive load and does not significantly
  441. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  442. * heater. If your configuration is significantly different than this and you don't understand
  443. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  444. */
  445. #define PIDTEMPBED
  446. //#define BED_LIMIT_SWITCHING
  447. /**
  448. * Max Bed Power
  449. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  450. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  451. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  452. */
  453. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  454. #if ENABLED(PIDTEMPBED)
  455. //#define MIN_BED_POWER 0
  456. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  457. //24V 500W silicone heater on to 4mm glass CartesioW
  458. #define DEFAULT_bedKp 390
  459. #define DEFAULT_bedKi 70
  460. #define DEFAULT_bedKd 546
  461. //24V 250W silicone heater on to 4mm glass CartesioM
  462. //#define DEFAULT_bedKp 303
  463. //#define DEFAULT_bedKi 42
  464. //#define DEFAULT_bedKd 539
  465. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  466. #endif // PIDTEMPBED
  467. // @section extruder
  468. /**
  469. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  470. * Add M302 to set the minimum extrusion temperature and/or turn
  471. * cold extrusion prevention on and off.
  472. *
  473. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  474. */
  475. #define PREVENT_COLD_EXTRUSION
  476. #define EXTRUDE_MINTEMP 170
  477. /**
  478. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  479. * Note: For Bowden Extruders make this large enough to allow load/unload.
  480. */
  481. #define PREVENT_LENGTHY_EXTRUDE
  482. #define EXTRUDE_MAXLENGTH 200
  483. //===========================================================================
  484. //======================== Thermal Runaway Protection =======================
  485. //===========================================================================
  486. /**
  487. * Thermal Protection provides additional protection to your printer from damage
  488. * and fire. Marlin always includes safe min and max temperature ranges which
  489. * protect against a broken or disconnected thermistor wire.
  490. *
  491. * The issue: If a thermistor falls out, it will report the much lower
  492. * temperature of the air in the room, and the the firmware will keep
  493. * the heater on.
  494. *
  495. * If you get "Thermal Runaway" or "Heating failed" errors the
  496. * details can be tuned in Configuration_adv.h
  497. */
  498. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  499. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  500. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  501. //===========================================================================
  502. //============================= Mechanical Settings =========================
  503. //===========================================================================
  504. // @section machine
  505. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  506. // either in the usual order or reversed
  507. //#define COREXY
  508. //#define COREXZ
  509. //#define COREYZ
  510. //#define COREYX
  511. //#define COREZX
  512. //#define COREZY
  513. //===========================================================================
  514. //============================== Endstop Settings ===========================
  515. //===========================================================================
  516. // @section homing
  517. // Specify here all the endstop connectors that are connected to any endstop or probe.
  518. // Almost all printers will be using one per axis. Probes will use one or more of the
  519. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  520. #define USE_XMIN_PLUG
  521. #define USE_YMIN_PLUG
  522. #define USE_ZMIN_PLUG
  523. //#define USE_XMAX_PLUG
  524. //#define USE_YMAX_PLUG
  525. //#define USE_ZMAX_PLUG
  526. // Enable pullup for all endstops to prevent a floating state
  527. #define ENDSTOPPULLUPS
  528. #if DISABLED(ENDSTOPPULLUPS)
  529. // Disable ENDSTOPPULLUPS to set pullups individually
  530. //#define ENDSTOPPULLUP_XMAX
  531. //#define ENDSTOPPULLUP_YMAX
  532. //#define ENDSTOPPULLUP_ZMAX
  533. //#define ENDSTOPPULLUP_XMIN
  534. //#define ENDSTOPPULLUP_YMIN
  535. //#define ENDSTOPPULLUP_ZMIN
  536. //#define ENDSTOPPULLUP_ZMIN_PROBE
  537. #endif
  538. // Enable pulldown for all endstops to prevent a floating state
  539. //#define ENDSTOPPULLDOWNS
  540. #if DISABLED(ENDSTOPPULLDOWNS)
  541. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  542. //#define ENDSTOPPULLDOWN_XMAX
  543. //#define ENDSTOPPULLDOWN_YMAX
  544. //#define ENDSTOPPULLDOWN_ZMAX
  545. //#define ENDSTOPPULLDOWN_XMIN
  546. //#define ENDSTOPPULLDOWN_YMIN
  547. //#define ENDSTOPPULLDOWN_ZMIN
  548. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  549. #endif
  550. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  551. #define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  552. #define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  553. #define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  554. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  555. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  556. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  557. #define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
  558. /**
  559. * Stepper Drivers
  560. *
  561. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  562. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  563. *
  564. * A4988 is assumed for unspecified drivers.
  565. *
  566. * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  567. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  568. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  569. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  570. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  571. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  572. */
  573. //#define X_DRIVER_TYPE A4988
  574. //#define Y_DRIVER_TYPE A4988
  575. //#define Z_DRIVER_TYPE A4988
  576. //#define X2_DRIVER_TYPE A4988
  577. //#define Y2_DRIVER_TYPE A4988
  578. //#define Z2_DRIVER_TYPE A4988
  579. //#define Z3_DRIVER_TYPE A4988
  580. //#define E0_DRIVER_TYPE A4988
  581. //#define E1_DRIVER_TYPE A4988
  582. //#define E2_DRIVER_TYPE A4988
  583. //#define E3_DRIVER_TYPE A4988
  584. //#define E4_DRIVER_TYPE A4988
  585. //#define E5_DRIVER_TYPE A4988
  586. // Enable this feature if all enabled endstop pins are interrupt-capable.
  587. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  588. //#define ENDSTOP_INTERRUPTS_FEATURE
  589. /**
  590. * Endstop Noise Threshold
  591. *
  592. * Enable if your probe or endstops falsely trigger due to noise.
  593. *
  594. * - Higher values may affect repeatability or accuracy of some bed probes.
  595. * - To fix noise install a 100nF ceramic capacitor inline with the switch.
  596. * - This feature is not required for common micro-switches mounted on PCBs
  597. * based on the Makerbot design, which already have the 100nF capacitor.
  598. *
  599. * :[2,3,4,5,6,7]
  600. */
  601. //#define ENDSTOP_NOISE_THRESHOLD 2
  602. //=============================================================================
  603. //============================== Movement Settings ============================
  604. //=============================================================================
  605. // @section motion
  606. /**
  607. * Default Settings
  608. *
  609. * These settings can be reset by M502
  610. *
  611. * Note that if EEPROM is enabled, saved values will override these.
  612. */
  613. /**
  614. * With this option each E stepper can have its own factors for the
  615. * following movement settings. If fewer factors are given than the
  616. * total number of extruders, the last value applies to the rest.
  617. */
  618. //#define DISTINCT_E_FACTORS
  619. /**
  620. * Default Axis Steps Per Unit (steps/mm)
  621. * Override with M92
  622. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  623. */
  624. #define DEFAULT_AXIS_STEPS_PER_UNIT { 71.128, 71.128, 640, 152 }
  625. /**
  626. * Default Max Feed Rate (mm/s)
  627. * Override with M203
  628. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  629. */
  630. #define DEFAULT_MAX_FEEDRATE { 200, 200, 20, 20 }
  631. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  632. #if ENABLED(LIMITED_MAX_FR_EDITING)
  633. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  634. #endif
  635. /**
  636. * Default Max Acceleration (change/s) change = mm/s
  637. * (Maximum start speed for accelerated moves)
  638. * Override with M201
  639. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  640. */
  641. #define DEFAULT_MAX_ACCELERATION { 1000, 1000, 100, 10000 }
  642. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  643. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  644. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  645. #endif
  646. /**
  647. * Default Acceleration (change/s) change = mm/s
  648. * Override with M204
  649. *
  650. * M204 P Acceleration
  651. * M204 R Retract Acceleration
  652. * M204 T Travel Acceleration
  653. */
  654. #define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
  655. #define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration for retracts
  656. #define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
  657. /**
  658. * Default Jerk limits (mm/s)
  659. * Override with M205 X Y Z E
  660. *
  661. * "Jerk" specifies the minimum speed change that requires acceleration.
  662. * When changing speed and direction, if the difference is less than the
  663. * value set here, it may happen instantaneously.
  664. */
  665. //#define CLASSIC_JERK
  666. #if ENABLED(CLASSIC_JERK)
  667. #define DEFAULT_XJERK 10.0
  668. #define DEFAULT_YJERK 10.0
  669. #define DEFAULT_ZJERK 0.3
  670. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  671. #if ENABLED(LIMITED_JERK_EDITING)
  672. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  673. #endif
  674. #endif
  675. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  676. /**
  677. * Junction Deviation Factor
  678. *
  679. * See:
  680. * https://reprap.org/forum/read.php?1,739819
  681. * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  682. */
  683. #if DISABLED(CLASSIC_JERK)
  684. #define JUNCTION_DEVIATION_MM 0.08 // (mm) Distance from real junction edge
  685. #endif
  686. /**
  687. * S-Curve Acceleration
  688. *
  689. * This option eliminates vibration during printing by fitting a Bézier
  690. * curve to move acceleration, producing much smoother direction changes.
  691. *
  692. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  693. */
  694. //#define S_CURVE_ACCELERATION
  695. //===========================================================================
  696. //============================= Z Probe Options =============================
  697. //===========================================================================
  698. // @section probes
  699. //
  700. // See http://marlinfw.org/docs/configuration/probes.html
  701. //
  702. /**
  703. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  704. *
  705. * Enable this option for a probe connected to the Z Min endstop pin.
  706. */
  707. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  708. /**
  709. * Z_MIN_PROBE_PIN
  710. *
  711. * Define this pin if the probe is not connected to Z_MIN_PIN.
  712. * If not defined the default pin for the selected MOTHERBOARD
  713. * will be used. Most of the time the default is what you want.
  714. *
  715. * - The simplest option is to use a free endstop connector.
  716. * - Use 5V for powered (usually inductive) sensors.
  717. *
  718. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  719. * - For simple switches connect...
  720. * - normally-closed switches to GND and D32.
  721. * - normally-open switches to 5V and D32.
  722. *
  723. */
  724. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  725. /**
  726. * Probe Type
  727. *
  728. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  729. * Activate one of these to use Auto Bed Leveling below.
  730. */
  731. /**
  732. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  733. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  734. * or (with LCD_BED_LEVELING) the LCD controller.
  735. */
  736. //#define PROBE_MANUALLY
  737. //#define MANUAL_PROBE_START_Z 0.2
  738. /**
  739. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  740. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  741. */
  742. //#define FIX_MOUNTED_PROBE
  743. /**
  744. * Z Servo Probe, such as an endstop switch on a rotating arm.
  745. */
  746. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  747. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  748. /**
  749. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  750. */
  751. //#define BLTOUCH
  752. /**
  753. * Touch-MI Probe by hotends.fr
  754. *
  755. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  756. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  757. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  758. *
  759. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  760. * and a minimum Z_HOMING_HEIGHT of 10.
  761. */
  762. //#define TOUCH_MI_PROBE
  763. #if ENABLED(TOUCH_MI_PROBE)
  764. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  765. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  766. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  767. #endif
  768. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  769. //#define SOLENOID_PROBE
  770. // A sled-mounted probe like those designed by Charles Bell.
  771. //#define Z_PROBE_SLED
  772. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  773. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  774. //#define RACK_AND_PINION_PROBE
  775. #if ENABLED(RACK_AND_PINION_PROBE)
  776. #define Z_PROBE_DEPLOY_X X_MIN_POS
  777. #define Z_PROBE_RETRACT_X X_MAX_POS
  778. #endif
  779. //
  780. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  781. //
  782. /**
  783. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  784. *
  785. * In the following example the X and Y offsets are both positive:
  786. *
  787. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  788. *
  789. * +-- BACK ---+
  790. * | |
  791. * L | (+) P | R <-- probe (20,20)
  792. * E | | I
  793. * F | (-) N (+) | G <-- nozzle (10,10)
  794. * T | | H
  795. * | (-) | T
  796. * | |
  797. * O-- FRONT --+
  798. * (0,0)
  799. *
  800. * Specify a Probe position as { X, Y, Z }
  801. */
  802. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  803. // Certain types of probes need to stay away from edges
  804. #define MIN_PROBE_EDGE 10
  805. // X and Y axis travel speed (mm/m) between probes
  806. #define XY_PROBE_SPEED 8000
  807. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  808. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  809. // Feedrate (mm/m) for the "accurate" probe of each point
  810. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  811. /**
  812. * Multiple Probing
  813. *
  814. * You may get improved results by probing 2 or more times.
  815. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  816. *
  817. * A total of 2 does fast/slow probes with a weighted average.
  818. * A total of 3 or more adds more slow probes, taking the average.
  819. */
  820. //#define MULTIPLE_PROBING 2
  821. //#define EXTRA_PROBING 1
  822. /**
  823. * Z probes require clearance when deploying, stowing, and moving between
  824. * probe points to avoid hitting the bed and other hardware.
  825. * Servo-mounted probes require extra space for the arm to rotate.
  826. * Inductive probes need space to keep from triggering early.
  827. *
  828. * Use these settings to specify the distance (mm) to raise the probe (or
  829. * lower the bed). The values set here apply over and above any (negative)
  830. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  831. * Only integer values >= 1 are valid here.
  832. *
  833. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  834. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  835. */
  836. #define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
  837. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  838. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  839. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  840. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  841. // For M851 give a range for adjusting the Z probe offset
  842. #define Z_PROBE_OFFSET_RANGE_MIN -20
  843. #define Z_PROBE_OFFSET_RANGE_MAX 20
  844. // Enable the M48 repeatability test to test probe accuracy
  845. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  846. // Before deploy/stow pause for user confirmation
  847. //#define PAUSE_BEFORE_DEPLOY_STOW
  848. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  849. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  850. #endif
  851. /**
  852. * Enable one or more of the following if probing seems unreliable.
  853. * Heaters and/or fans can be disabled during probing to minimize electrical
  854. * noise. A delay can also be added to allow noise and vibration to settle.
  855. * These options are most useful for the BLTouch probe, but may also improve
  856. * readings with inductive probes and piezo sensors.
  857. */
  858. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  859. #if ENABLED(PROBING_HEATERS_OFF)
  860. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  861. #endif
  862. //#define PROBING_FANS_OFF // Turn fans off when probing
  863. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  864. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  865. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  866. // :{ 0:'Low', 1:'High' }
  867. #define X_ENABLE_ON 1
  868. #define Y_ENABLE_ON 1
  869. #define Z_ENABLE_ON 1
  870. #define E_ENABLE_ON 0 // For all extruders
  871. // Disables axis stepper immediately when it's not being used.
  872. // WARNING: When motors turn off there is a chance of losing position accuracy!
  873. #define DISABLE_X false
  874. #define DISABLE_Y false
  875. #define DISABLE_Z false
  876. // Warn on display about possibly reduced accuracy
  877. //#define DISABLE_REDUCED_ACCURACY_WARNING
  878. // @section extruder
  879. #define DISABLE_E false // For all extruders
  880. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  881. // @section machine
  882. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  883. #define INVERT_X_DIR false
  884. #define INVERT_Y_DIR true
  885. #define INVERT_Z_DIR false
  886. // @section extruder
  887. // For direct drive extruder v9 set to true, for geared extruder set to false.
  888. #define INVERT_E0_DIR false
  889. #define INVERT_E1_DIR false
  890. #define INVERT_E2_DIR false
  891. #define INVERT_E3_DIR false
  892. #define INVERT_E4_DIR false
  893. #define INVERT_E5_DIR false
  894. // @section homing
  895. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  896. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  897. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  898. // Be sure you have this distance over your Z_MAX_POS in case.
  899. // Direction of endstops when homing; 1=MAX, -1=MIN
  900. // :[-1,1]
  901. #define X_HOME_DIR -1
  902. #define Y_HOME_DIR -1
  903. #define Z_HOME_DIR -1
  904. // @section machine
  905. // The size of the print bed
  906. #define X_BED_SIZE 435
  907. #define Y_BED_SIZE 270
  908. // Travel limits (mm) after homing, corresponding to endstop positions.
  909. #define X_MIN_POS 0
  910. #define Y_MIN_POS 0
  911. #define Z_MIN_POS 0
  912. #define X_MAX_POS X_BED_SIZE
  913. #define Y_MAX_POS Y_BED_SIZE
  914. #define Z_MAX_POS 400
  915. /**
  916. * Software Endstops
  917. *
  918. * - Prevent moves outside the set machine bounds.
  919. * - Individual axes can be disabled, if desired.
  920. * - X and Y only apply to Cartesian robots.
  921. * - Use 'M211' to set software endstops on/off or report current state
  922. */
  923. // Min software endstops constrain movement within minimum coordinate bounds
  924. #define MIN_SOFTWARE_ENDSTOPS
  925. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  926. #define MIN_SOFTWARE_ENDSTOP_X
  927. #define MIN_SOFTWARE_ENDSTOP_Y
  928. #define MIN_SOFTWARE_ENDSTOP_Z
  929. #endif
  930. // Max software endstops constrain movement within maximum coordinate bounds
  931. #define MAX_SOFTWARE_ENDSTOPS
  932. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  933. #define MAX_SOFTWARE_ENDSTOP_X
  934. #define MAX_SOFTWARE_ENDSTOP_Y
  935. #define MAX_SOFTWARE_ENDSTOP_Z
  936. #endif
  937. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  938. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  939. #endif
  940. /**
  941. * Filament Runout Sensors
  942. * Mechanical or opto endstops are used to check for the presence of filament.
  943. *
  944. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  945. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  946. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  947. */
  948. //#define FILAMENT_RUNOUT_SENSOR
  949. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  950. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  951. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
  952. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  953. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  954. // Set one or more commands to execute on filament runout.
  955. // (After 'M412 H' Marlin will ask the host to handle the process.)
  956. #define FILAMENT_RUNOUT_SCRIPT "M600"
  957. // After a runout is detected, continue printing this length of filament
  958. // before executing the runout script. Useful for a sensor at the end of
  959. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  960. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  961. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  962. // Enable this option to use an encoder disc that toggles the runout pin
  963. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  964. // large enough to avoid false positives.)
  965. //#define FILAMENT_MOTION_SENSOR
  966. #endif
  967. #endif
  968. //===========================================================================
  969. //=============================== Bed Leveling ==============================
  970. //===========================================================================
  971. // @section calibrate
  972. /**
  973. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  974. * and behavior of G29 will change depending on your selection.
  975. *
  976. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  977. *
  978. * - AUTO_BED_LEVELING_3POINT
  979. * Probe 3 arbitrary points on the bed (that aren't collinear)
  980. * You specify the XY coordinates of all 3 points.
  981. * The result is a single tilted plane. Best for a flat bed.
  982. *
  983. * - AUTO_BED_LEVELING_LINEAR
  984. * Probe several points in a grid.
  985. * You specify the rectangle and the density of sample points.
  986. * The result is a single tilted plane. Best for a flat bed.
  987. *
  988. * - AUTO_BED_LEVELING_BILINEAR
  989. * Probe several points in a grid.
  990. * You specify the rectangle and the density of sample points.
  991. * The result is a mesh, best for large or uneven beds.
  992. *
  993. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  994. * A comprehensive bed leveling system combining the features and benefits
  995. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  996. * Validation and Mesh Editing systems.
  997. *
  998. * - MESH_BED_LEVELING
  999. * Probe a grid manually
  1000. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1001. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1002. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1003. * With an LCD controller the process is guided step-by-step.
  1004. */
  1005. //#define AUTO_BED_LEVELING_3POINT
  1006. //#define AUTO_BED_LEVELING_LINEAR
  1007. //#define AUTO_BED_LEVELING_BILINEAR
  1008. //#define AUTO_BED_LEVELING_UBL
  1009. //#define MESH_BED_LEVELING
  1010. /**
  1011. * Normally G28 leaves leveling disabled on completion. Enable
  1012. * this option to have G28 restore the prior leveling state.
  1013. */
  1014. //#define RESTORE_LEVELING_AFTER_G28
  1015. /**
  1016. * Enable detailed logging of G28, G29, M48, etc.
  1017. * Turn on with the command 'M111 S32'.
  1018. * NOTE: Requires a lot of PROGMEM!
  1019. */
  1020. //#define DEBUG_LEVELING_FEATURE
  1021. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1022. // Gradually reduce leveling correction until a set height is reached,
  1023. // at which point movement will be level to the machine's XY plane.
  1024. // The height can be set with M420 Z<height>
  1025. #define ENABLE_LEVELING_FADE_HEIGHT
  1026. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1027. // split up moves into short segments like a Delta. This follows the
  1028. // contours of the bed more closely than edge-to-edge straight moves.
  1029. #define SEGMENT_LEVELED_MOVES
  1030. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1031. /**
  1032. * Enable the G26 Mesh Validation Pattern tool.
  1033. */
  1034. //#define G26_MESH_VALIDATION
  1035. #if ENABLED(G26_MESH_VALIDATION)
  1036. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1037. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1038. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1039. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1040. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1041. #endif
  1042. #endif
  1043. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1044. // Set the number of grid points per dimension.
  1045. #define GRID_MAX_POINTS_X 3
  1046. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1047. // Probe along the Y axis, advancing X after each column
  1048. //#define PROBE_Y_FIRST
  1049. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1050. // Beyond the probed grid, continue the implied tilt?
  1051. // Default is to maintain the height of the nearest edge.
  1052. //#define EXTRAPOLATE_BEYOND_GRID
  1053. //
  1054. // Experimental Subdivision of the grid by Catmull-Rom method.
  1055. // Synthesizes intermediate points to produce a more detailed mesh.
  1056. //
  1057. //#define ABL_BILINEAR_SUBDIVISION
  1058. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1059. // Number of subdivisions between probe points
  1060. #define BILINEAR_SUBDIVISIONS 3
  1061. #endif
  1062. #endif
  1063. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1064. //===========================================================================
  1065. //========================= Unified Bed Leveling ============================
  1066. //===========================================================================
  1067. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1068. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1069. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1070. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1071. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1072. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1073. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1074. // as the Z-Height correction value.
  1075. #elif ENABLED(MESH_BED_LEVELING)
  1076. //===========================================================================
  1077. //=================================== Mesh ==================================
  1078. //===========================================================================
  1079. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1080. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1081. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1082. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1083. #endif // BED_LEVELING
  1084. /**
  1085. * Add a bed leveling sub-menu for ABL or MBL.
  1086. * Include a guided procedure if manual probing is enabled.
  1087. */
  1088. //#define LCD_BED_LEVELING
  1089. #if ENABLED(LCD_BED_LEVELING)
  1090. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1091. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1092. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1093. #endif
  1094. // Add a menu item to move between bed corners for manual bed adjustment
  1095. //#define LEVEL_BED_CORNERS
  1096. #if ENABLED(LEVEL_BED_CORNERS)
  1097. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1098. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
  1099. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1100. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1101. #endif
  1102. /**
  1103. * Commands to execute at the end of G29 probing.
  1104. * Useful to retract or move the Z probe out of the way.
  1105. */
  1106. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1107. // @section homing
  1108. // The center of the bed is at (X=0, Y=0)
  1109. //#define BED_CENTER_AT_0_0
  1110. // Manually set the home position. Leave these undefined for automatic settings.
  1111. // For DELTA this is the top-center of the Cartesian print volume.
  1112. //#define MANUAL_X_HOME_POS 0
  1113. //#define MANUAL_Y_HOME_POS 0
  1114. //#define MANUAL_Z_HOME_POS 0
  1115. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1116. //
  1117. // With this feature enabled:
  1118. //
  1119. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1120. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1121. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1122. // - Prevent Z homing when the Z probe is outside bed area.
  1123. //
  1124. //#define Z_SAFE_HOMING
  1125. #if ENABLED(Z_SAFE_HOMING)
  1126. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1127. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1128. #endif
  1129. // Homing speeds (mm/m)
  1130. #define HOMING_FEEDRATE_XY (50*60)
  1131. #define HOMING_FEEDRATE_Z (10*60)
  1132. // Validate that endstops are triggered on homing moves
  1133. #define VALIDATE_HOMING_ENDSTOPS
  1134. // @section calibrate
  1135. /**
  1136. * Bed Skew Compensation
  1137. *
  1138. * This feature corrects for misalignment in the XYZ axes.
  1139. *
  1140. * Take the following steps to get the bed skew in the XY plane:
  1141. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1142. * 2. For XY_DIAG_AC measure the diagonal A to C
  1143. * 3. For XY_DIAG_BD measure the diagonal B to D
  1144. * 4. For XY_SIDE_AD measure the edge A to D
  1145. *
  1146. * Marlin automatically computes skew factors from these measurements.
  1147. * Skew factors may also be computed and set manually:
  1148. *
  1149. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1150. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1151. *
  1152. * If desired, follow the same procedure for XZ and YZ.
  1153. * Use these diagrams for reference:
  1154. *
  1155. * Y Z Z
  1156. * ^ B-------C ^ B-------C ^ B-------C
  1157. * | / / | / / | / /
  1158. * | / / | / / | / /
  1159. * | A-------D | A-------D | A-------D
  1160. * +-------------->X +-------------->X +-------------->Y
  1161. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1162. */
  1163. //#define SKEW_CORRECTION
  1164. #if ENABLED(SKEW_CORRECTION)
  1165. // Input all length measurements here:
  1166. #define XY_DIAG_AC 282.8427124746
  1167. #define XY_DIAG_BD 282.8427124746
  1168. #define XY_SIDE_AD 200
  1169. // Or, set the default skew factors directly here
  1170. // to override the above measurements:
  1171. #define XY_SKEW_FACTOR 0.0
  1172. //#define SKEW_CORRECTION_FOR_Z
  1173. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1174. #define XZ_DIAG_AC 282.8427124746
  1175. #define XZ_DIAG_BD 282.8427124746
  1176. #define YZ_DIAG_AC 282.8427124746
  1177. #define YZ_DIAG_BD 282.8427124746
  1178. #define YZ_SIDE_AD 200
  1179. #define XZ_SKEW_FACTOR 0.0
  1180. #define YZ_SKEW_FACTOR 0.0
  1181. #endif
  1182. // Enable this option for M852 to set skew at runtime
  1183. //#define SKEW_CORRECTION_GCODE
  1184. #endif
  1185. //=============================================================================
  1186. //============================= Additional Features ===========================
  1187. //=============================================================================
  1188. // @section extras
  1189. /**
  1190. * EEPROM
  1191. *
  1192. * Persistent storage to preserve configurable settings across reboots.
  1193. *
  1194. * M500 - Store settings to EEPROM.
  1195. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1196. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1197. */
  1198. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1199. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1200. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1201. #if ENABLED(EEPROM_SETTINGS)
  1202. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1203. #endif
  1204. //
  1205. // Host Keepalive
  1206. //
  1207. // When enabled Marlin will send a busy status message to the host
  1208. // every couple of seconds when it can't accept commands.
  1209. //
  1210. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1211. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1212. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1213. //
  1214. // M100 Free Memory Watcher
  1215. //
  1216. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1217. //
  1218. // G20/G21 Inch mode support
  1219. //
  1220. //#define INCH_MODE_SUPPORT
  1221. //
  1222. // M149 Set temperature units support
  1223. //
  1224. //#define TEMPERATURE_UNITS_SUPPORT
  1225. // @section temperature
  1226. // Preheat Constants
  1227. #define PREHEAT_1_LABEL "PLA"
  1228. #define PREHEAT_1_TEMP_HOTEND 190
  1229. #define PREHEAT_1_TEMP_BED 50
  1230. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1231. #define PREHEAT_2_LABEL "ABS"
  1232. #define PREHEAT_2_TEMP_HOTEND 240
  1233. #define PREHEAT_2_TEMP_BED 110
  1234. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1235. /**
  1236. * Nozzle Park
  1237. *
  1238. * Park the nozzle at the given XYZ position on idle or G27.
  1239. *
  1240. * The "P" parameter controls the action applied to the Z axis:
  1241. *
  1242. * P0 (Default) If Z is below park Z raise the nozzle.
  1243. * P1 Raise the nozzle always to Z-park height.
  1244. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1245. */
  1246. //#define NOZZLE_PARK_FEATURE
  1247. #if ENABLED(NOZZLE_PARK_FEATURE)
  1248. // Specify a park position as { X, Y, Z_raise }
  1249. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1250. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1251. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1252. #endif
  1253. /**
  1254. * Clean Nozzle Feature -- EXPERIMENTAL
  1255. *
  1256. * Adds the G12 command to perform a nozzle cleaning process.
  1257. *
  1258. * Parameters:
  1259. * P Pattern
  1260. * S Strokes / Repetitions
  1261. * T Triangles (P1 only)
  1262. *
  1263. * Patterns:
  1264. * P0 Straight line (default). This process requires a sponge type material
  1265. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1266. * between the start / end points.
  1267. *
  1268. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1269. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1270. * Zig-zags are done in whichever is the narrower dimension.
  1271. * For example, "G12 P1 S1 T3" will execute:
  1272. *
  1273. * --
  1274. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1275. * | | / \ / \ / \ |
  1276. * A | | / \ / \ / \ |
  1277. * | | / \ / \ / \ |
  1278. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1279. * -- +--------------------------------+
  1280. * |________|_________|_________|
  1281. * T1 T2 T3
  1282. *
  1283. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1284. * "R" specifies the radius. "S" specifies the stroke count.
  1285. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1286. *
  1287. * Caveats: The ending Z should be the same as starting Z.
  1288. * Attention: EXPERIMENTAL. G-code arguments may change.
  1289. *
  1290. */
  1291. //#define NOZZLE_CLEAN_FEATURE
  1292. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1293. // Default number of pattern repetitions
  1294. #define NOZZLE_CLEAN_STROKES 12
  1295. // Default number of triangles
  1296. #define NOZZLE_CLEAN_TRIANGLES 3
  1297. // Specify positions as { X, Y, Z }
  1298. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1) }
  1299. #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) }
  1300. // Circular pattern radius
  1301. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1302. // Circular pattern circle fragments number
  1303. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1304. // Middle point of circle
  1305. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1306. // Move the nozzle to the initial position after cleaning
  1307. #define NOZZLE_CLEAN_GOBACK
  1308. // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
  1309. //#define NOZZLE_CLEAN_NO_Z
  1310. #endif
  1311. /**
  1312. * Print Job Timer
  1313. *
  1314. * Automatically start and stop the print job timer on M104/M109/M190.
  1315. *
  1316. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1317. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1318. * M190 (bed, wait) - high temp = start timer, low temp = none
  1319. *
  1320. * The timer can also be controlled with the following commands:
  1321. *
  1322. * M75 - Start the print job timer
  1323. * M76 - Pause the print job timer
  1324. * M77 - Stop the print job timer
  1325. */
  1326. #define PRINTJOB_TIMER_AUTOSTART
  1327. /**
  1328. * Print Counter
  1329. *
  1330. * Track statistical data such as:
  1331. *
  1332. * - Total print jobs
  1333. * - Total successful print jobs
  1334. * - Total failed print jobs
  1335. * - Total time printing
  1336. *
  1337. * View the current statistics with M78.
  1338. */
  1339. //#define PRINTCOUNTER
  1340. //=============================================================================
  1341. //============================= LCD and SD support ============================
  1342. //=============================================================================
  1343. // @section lcd
  1344. /**
  1345. * LCD LANGUAGE
  1346. *
  1347. * Select the language to display on the LCD. These languages are available:
  1348. *
  1349. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
  1350. * ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1351. *
  1352. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1353. */
  1354. #define LCD_LANGUAGE en
  1355. /**
  1356. * LCD Character Set
  1357. *
  1358. * Note: This option is NOT applicable to Graphical Displays.
  1359. *
  1360. * All character-based LCDs provide ASCII plus one of these
  1361. * language extensions:
  1362. *
  1363. * - JAPANESE ... the most common
  1364. * - WESTERN ... with more accented characters
  1365. * - CYRILLIC ... for the Russian language
  1366. *
  1367. * To determine the language extension installed on your controller:
  1368. *
  1369. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1370. * - Click the controller to view the LCD menu
  1371. * - The LCD will display Japanese, Western, or Cyrillic text
  1372. *
  1373. * See http://marlinfw.org/docs/development/lcd_language.html
  1374. *
  1375. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1376. */
  1377. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1378. /**
  1379. * Info Screen Style (0:Classic, 1:Prusa)
  1380. *
  1381. * :[0:'Classic', 1:'Prusa']
  1382. */
  1383. #define LCD_INFO_SCREEN_STYLE 0
  1384. /**
  1385. * SD CARD
  1386. *
  1387. * SD Card support is disabled by default. If your controller has an SD slot,
  1388. * you must uncomment the following option or it won't work.
  1389. *
  1390. */
  1391. #define SDSUPPORT
  1392. /**
  1393. * SD CARD: SPI SPEED
  1394. *
  1395. * Enable one of the following items for a slower SPI transfer speed.
  1396. * This may be required to resolve "volume init" errors.
  1397. */
  1398. //#define SPI_SPEED SPI_HALF_SPEED
  1399. //#define SPI_SPEED SPI_QUARTER_SPEED
  1400. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1401. /**
  1402. * SD CARD: ENABLE CRC
  1403. *
  1404. * Use CRC checks and retries on the SD communication.
  1405. */
  1406. //#define SD_CHECK_AND_RETRY
  1407. /**
  1408. * LCD Menu Items
  1409. *
  1410. * Disable all menus and only display the Status Screen, or
  1411. * just remove some extraneous menu items to recover space.
  1412. */
  1413. //#define NO_LCD_MENUS
  1414. //#define SLIM_LCD_MENUS
  1415. //
  1416. // ENCODER SETTINGS
  1417. //
  1418. // This option overrides the default number of encoder pulses needed to
  1419. // produce one step. Should be increased for high-resolution encoders.
  1420. //
  1421. #define ENCODER_PULSES_PER_STEP 2
  1422. //
  1423. // Use this option to override the number of step signals required to
  1424. // move between next/prev menu items.
  1425. //
  1426. #define ENCODER_STEPS_PER_MENU_ITEM 1
  1427. /**
  1428. * Encoder Direction Options
  1429. *
  1430. * Test your encoder's behavior first with both options disabled.
  1431. *
  1432. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1433. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1434. * Reversed Value Editing only? Enable BOTH options.
  1435. */
  1436. //
  1437. // This option reverses the encoder direction everywhere.
  1438. //
  1439. // Set this option if CLOCKWISE causes values to DECREASE
  1440. //
  1441. //#define REVERSE_ENCODER_DIRECTION
  1442. //
  1443. // This option reverses the encoder direction for navigating LCD menus.
  1444. //
  1445. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1446. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1447. //
  1448. //#define REVERSE_MENU_DIRECTION
  1449. //
  1450. // This option reverses the encoder direction for Select Screen.
  1451. //
  1452. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1453. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1454. //
  1455. //#define REVERSE_SELECT_DIRECTION
  1456. //
  1457. // Individual Axis Homing
  1458. //
  1459. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1460. //
  1461. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1462. //
  1463. // SPEAKER/BUZZER
  1464. //
  1465. // If you have a speaker that can produce tones, enable it here.
  1466. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1467. //
  1468. #define SPEAKER
  1469. //
  1470. // The duration and frequency for the UI feedback sound.
  1471. // Set these to 0 to disable audio feedback in the LCD menus.
  1472. //
  1473. // Note: Test audio output with the G-Code:
  1474. // M300 S<frequency Hz> P<duration ms>
  1475. //
  1476. #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1477. #define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1478. //=============================================================================
  1479. //======================== LCD / Controller Selection =========================
  1480. //======================== (Character-based LCDs) =========================
  1481. //=============================================================================
  1482. //
  1483. // RepRapDiscount Smart Controller.
  1484. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1485. //
  1486. // Note: Usually sold with a white PCB.
  1487. //
  1488. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1489. //
  1490. // Original RADDS LCD Display+Encoder+SDCardReader
  1491. // http://doku.radds.org/dokumentation/lcd-display/
  1492. //
  1493. //#define RADDS_DISPLAY
  1494. //
  1495. // ULTIMAKER Controller.
  1496. //
  1497. //#define ULTIMAKERCONTROLLER
  1498. //
  1499. // ULTIPANEL as seen on Thingiverse.
  1500. //
  1501. //#define ULTIPANEL
  1502. //
  1503. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1504. // http://reprap.org/wiki/PanelOne
  1505. //
  1506. //#define PANEL_ONE
  1507. //
  1508. // GADGETS3D G3D LCD/SD Controller
  1509. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1510. //
  1511. // Note: Usually sold with a blue PCB.
  1512. //
  1513. //#define G3D_PANEL
  1514. //
  1515. // RigidBot Panel V1.0
  1516. // http://www.inventapart.com/
  1517. //
  1518. //#define RIGIDBOT_PANEL
  1519. //
  1520. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1521. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1522. //
  1523. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1524. //
  1525. // ANET and Tronxy 20x4 Controller
  1526. //
  1527. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1528. // This LCD is known to be susceptible to electrical interference
  1529. // which scrambles the display. Pressing any button clears it up.
  1530. // This is a LCD2004 display with 5 analog buttons.
  1531. //
  1532. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1533. //
  1534. //#define ULTRA_LCD
  1535. //=============================================================================
  1536. //======================== LCD / Controller Selection =========================
  1537. //===================== (I2C and Shift-Register LCDs) =====================
  1538. //=============================================================================
  1539. //
  1540. // CONTROLLER TYPE: I2C
  1541. //
  1542. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1543. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1544. //
  1545. //
  1546. // Elefu RA Board Control Panel
  1547. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1548. //
  1549. //#define RA_CONTROL_PANEL
  1550. //
  1551. // Sainsmart (YwRobot) LCD Displays
  1552. //
  1553. // These require F.Malpartida's LiquidCrystal_I2C library
  1554. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1555. //
  1556. //#define LCD_SAINSMART_I2C_1602
  1557. //#define LCD_SAINSMART_I2C_2004
  1558. //
  1559. // Generic LCM1602 LCD adapter
  1560. //
  1561. //#define LCM1602
  1562. //
  1563. // PANELOLU2 LCD with status LEDs,
  1564. // separate encoder and click inputs.
  1565. //
  1566. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1567. // For more info: https://github.com/lincomatic/LiquidTWI2
  1568. //
  1569. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1570. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1571. //
  1572. //#define LCD_I2C_PANELOLU2
  1573. //
  1574. // Panucatt VIKI LCD with status LEDs,
  1575. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1576. //
  1577. //#define LCD_I2C_VIKI
  1578. //
  1579. // CONTROLLER TYPE: Shift register panels
  1580. //
  1581. //
  1582. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1583. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1584. //
  1585. //#define SAV_3DLCD
  1586. //
  1587. // 3-wire SR LCD with strobe using 74HC4094
  1588. // https://github.com/mikeshub/SailfishLCD
  1589. // Uses the code directly from Sailfish
  1590. //
  1591. //#define FF_INTERFACEBOARD
  1592. //=============================================================================
  1593. //======================= LCD / Controller Selection =======================
  1594. //========================= (Graphical LCDs) ========================
  1595. //=============================================================================
  1596. //
  1597. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1598. //
  1599. // IMPORTANT: The U8glib library is required for Graphical Display!
  1600. // https://github.com/olikraus/U8glib_Arduino
  1601. //
  1602. //
  1603. // RepRapDiscount FULL GRAPHIC Smart Controller
  1604. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1605. //
  1606. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1607. //
  1608. // ReprapWorld Graphical LCD
  1609. // https://reprapworld.com/?products_details&products_id/1218
  1610. //
  1611. //#define REPRAPWORLD_GRAPHICAL_LCD
  1612. //
  1613. // Activate one of these if you have a Panucatt Devices
  1614. // Viki 2.0 or mini Viki with Graphic LCD
  1615. // http://panucatt.com
  1616. //
  1617. //#define VIKI2
  1618. //#define miniVIKI
  1619. //
  1620. // MakerLab Mini Panel with graphic
  1621. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1622. //
  1623. //#define MINIPANEL
  1624. //
  1625. // MaKr3d Makr-Panel with graphic controller and SD support.
  1626. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1627. //
  1628. //#define MAKRPANEL
  1629. //
  1630. // Adafruit ST7565 Full Graphic Controller.
  1631. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1632. //
  1633. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1634. //
  1635. // BQ LCD Smart Controller shipped by
  1636. // default with the BQ Hephestos 2 and Witbox 2.
  1637. //
  1638. //#define BQ_LCD_SMART_CONTROLLER
  1639. //
  1640. // Cartesio UI
  1641. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1642. //
  1643. #define CARTESIO_UI
  1644. //
  1645. // LCD for Melzi Card with Graphical LCD
  1646. //
  1647. //#define LCD_FOR_MELZI
  1648. //
  1649. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1650. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1651. //
  1652. //#define ULTI_CONTROLLER
  1653. //
  1654. // MKS MINI12864 with graphic controller and SD support
  1655. // https://reprap.org/wiki/MKS_MINI_12864
  1656. //
  1657. //#define MKS_MINI_12864
  1658. //
  1659. // FYSETC variant of the MINI12864 graphic controller with SD support
  1660. // https://wiki.fysetc.com/Mini12864_Panel/
  1661. //
  1662. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1663. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1664. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1665. //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight
  1666. //
  1667. // Factory display for Creality CR-10
  1668. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1669. //
  1670. // This is RAMPS-compatible using a single 10-pin connector.
  1671. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1672. //
  1673. //#define CR10_STOCKDISPLAY
  1674. //
  1675. // ANET and Tronxy Graphical Controller
  1676. //
  1677. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1678. // A clone of the RepRapDiscount full graphics display but with
  1679. // different pins/wiring (see pins_ANET_10.h).
  1680. //
  1681. //#define ANET_FULL_GRAPHICS_LCD
  1682. //
  1683. // AZSMZ 12864 LCD with SD
  1684. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1685. //
  1686. //#define AZSMZ_12864
  1687. //
  1688. // Silvergate GLCD controller
  1689. // http://github.com/android444/Silvergate
  1690. //
  1691. //#define SILVER_GATE_GLCD_CONTROLLER
  1692. //=============================================================================
  1693. //============================== OLED Displays ==============================
  1694. //=============================================================================
  1695. //
  1696. // SSD1306 OLED full graphics generic display
  1697. //
  1698. //#define U8GLIB_SSD1306
  1699. //
  1700. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1701. //
  1702. //#define SAV_3DGLCD
  1703. #if ENABLED(SAV_3DGLCD)
  1704. #define U8GLIB_SSD1306
  1705. //#define U8GLIB_SH1106
  1706. #endif
  1707. //
  1708. // TinyBoy2 128x64 OLED / Encoder Panel
  1709. //
  1710. //#define OLED_PANEL_TINYBOY2
  1711. //
  1712. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1713. // http://reprap.org/wiki/MKS_12864OLED
  1714. //
  1715. // Tiny, but very sharp OLED display
  1716. //
  1717. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1718. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1719. //
  1720. // Einstart S OLED SSD1306
  1721. //
  1722. //#define U8GLIB_SH1106_EINSTART
  1723. //
  1724. // Overlord OLED display/controller with i2c buzzer and LEDs
  1725. //
  1726. //#define OVERLORD_OLED
  1727. //=============================================================================
  1728. //========================== Extensible UI Displays ===========================
  1729. //=============================================================================
  1730. //
  1731. // DGUS Touch Display with DWIN OS
  1732. //
  1733. //#define DGUS_LCD
  1734. //
  1735. // Touch-screen LCD for Malyan M200 printers
  1736. //
  1737. //#define MALYAN_LCD
  1738. //
  1739. // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
  1740. // See Configuration_adv.h for all configuration options.
  1741. //
  1742. //#define LULZBOT_TOUCH_UI
  1743. //
  1744. // Third-party or vendor-customized controller interfaces.
  1745. // Sources should be installed in 'src/lcd/extensible_ui'.
  1746. //
  1747. //#define EXTENSIBLE_UI
  1748. //=============================================================================
  1749. //=============================== Graphical TFTs ==============================
  1750. //=============================================================================
  1751. //
  1752. // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
  1753. //
  1754. //#define FSMC_GRAPHICAL_TFT
  1755. //=============================================================================
  1756. //============================ Other Controllers ============================
  1757. //=============================================================================
  1758. //
  1759. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  1760. //
  1761. //#define TOUCH_BUTTONS
  1762. #if ENABLED(TOUCH_BUTTONS)
  1763. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  1764. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  1765. #define XPT2046_X_CALIBRATION 12316
  1766. #define XPT2046_Y_CALIBRATION -8981
  1767. #define XPT2046_X_OFFSET -43
  1768. #define XPT2046_Y_OFFSET 257
  1769. #endif
  1770. //
  1771. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1772. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1773. //
  1774. #define REPRAPWORLD_KEYPAD
  1775. #define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  1776. //=============================================================================
  1777. //=============================== Extra Features ==============================
  1778. //=============================================================================
  1779. // @section extras
  1780. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1781. //#define FAST_PWM_FAN
  1782. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1783. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1784. // is too low, you should also increment SOFT_PWM_SCALE.
  1785. //#define FAN_SOFT_PWM
  1786. // Incrementing this by 1 will double the software PWM frequency,
  1787. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1788. // However, control resolution will be halved for each increment;
  1789. // at zero value, there are 128 effective control positions.
  1790. // :[0,1,2,3,4,5,6,7]
  1791. #define SOFT_PWM_SCALE 0
  1792. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1793. // be used to mitigate the associated resolution loss. If enabled,
  1794. // some of the PWM cycles are stretched so on average the desired
  1795. // duty cycle is attained.
  1796. //#define SOFT_PWM_DITHER
  1797. // Temperature status LEDs that display the hotend and bed temperature.
  1798. // If all hotends, bed temperature, and target temperature are under 54C
  1799. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1800. #define TEMP_STAT_LEDS
  1801. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1802. //#define SF_ARC_FIX
  1803. // Support for the BariCUDA Paste Extruder
  1804. //#define BARICUDA
  1805. // Support for BlinkM/CyzRgb
  1806. //#define BLINKM
  1807. // Support for PCA9632 PWM LED driver
  1808. //#define PCA9632
  1809. // Support for PCA9533 PWM LED driver
  1810. // https://github.com/mikeshub/SailfishRGB_LED
  1811. //#define PCA9533
  1812. /**
  1813. * RGB LED / LED Strip Control
  1814. *
  1815. * Enable support for an RGB LED connected to 5V digital pins, or
  1816. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1817. *
  1818. * Adds the M150 command to set the LED (or LED strip) color.
  1819. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1820. * luminance values can be set from 0 to 255.
  1821. * For Neopixel LED an overall brightness parameter is also available.
  1822. *
  1823. * *** CAUTION ***
  1824. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1825. * as the Arduino cannot handle the current the LEDs will require.
  1826. * Failure to follow this precaution can destroy your Arduino!
  1827. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1828. * more current than the Arduino 5V linear regulator can produce.
  1829. * *** CAUTION ***
  1830. *
  1831. * LED Type. Enable only one of the following two options.
  1832. *
  1833. */
  1834. //#define RGB_LED
  1835. //#define RGBW_LED
  1836. #if EITHER(RGB_LED, RGBW_LED)
  1837. //#define RGB_LED_R_PIN 34
  1838. //#define RGB_LED_G_PIN 43
  1839. //#define RGB_LED_B_PIN 35
  1840. //#define RGB_LED_W_PIN -1
  1841. #endif
  1842. // Support for Adafruit Neopixel LED driver
  1843. //#define NEOPIXEL_LED
  1844. #if ENABLED(NEOPIXEL_LED)
  1845. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1846. #define NEOPIXEL_PIN 4 // LED driving pin
  1847. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  1848. //#define NEOPIXEL2_PIN 5
  1849. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
  1850. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1851. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1852. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1853. // Use a single Neopixel LED for static (background) lighting
  1854. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  1855. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  1856. #endif
  1857. /**
  1858. * Printer Event LEDs
  1859. *
  1860. * During printing, the LEDs will reflect the printer status:
  1861. *
  1862. * - Gradually change from blue to violet as the heated bed gets to target temp
  1863. * - Gradually change from violet to red as the hotend gets to temperature
  1864. * - Change to white to illuminate work surface
  1865. * - Change to green once print has finished
  1866. * - Turn off after the print has finished and the user has pushed a button
  1867. */
  1868. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  1869. #define PRINTER_EVENT_LEDS
  1870. #endif
  1871. /**
  1872. * R/C SERVO support
  1873. * Sponsored by TrinityLabs, Reworked by codexmas
  1874. */
  1875. /**
  1876. * Number of servos
  1877. *
  1878. * For some servo-related options NUM_SERVOS will be set automatically.
  1879. * Set this manually if there are extra servos needing manual control.
  1880. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1881. */
  1882. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1883. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  1884. // 300ms is a good value but you can try less delay.
  1885. // If the servo can't reach the requested position, increase it.
  1886. #define SERVO_DELAY { 300 }
  1887. // Only power servos during movement, otherwise leave off to prevent jitter
  1888. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1889. // Allow servo angle to be edited and saved to EEPROM
  1890. //#define EDITABLE_SERVO_ANGLES