My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Você não pode selecionar mais de 25 tópicos Os tópicos devem começar com uma letra ou um número, podem incluir traços ('-') e podem ter até 35 caracteres.

Configuration.h 79KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720172117221723172417251726172717281729173017311732173317341735173617371738173917401741174217431744174517461747174817491750175117521753175417551756175717581759176017611762176317641765176617671768176917701771177217731774177517761777177817791780178117821783178417851786178717881789179017911792179317941795179617971798179918001801180218031804180518061807180818091810181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391840184118421843184418451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906190719081909191019111912191319141915191619171918191919201921192219231924192519261927192819291930193119321933193419351936193719381939194019411942194319441945194619471948194919501951195219531954195519561957195819591960196119621963196419651966196719681969197019711972197319741975197619771978197919801981198219831984198519861987198819891990199119921993199419951996199719981999200020012002200320042005200620072008200920102011201220132014201520162017201820192020202120222023202420252026202720282029203020312032203320342035203620372038203920402041204220432044204520462047204820492050205120522053205420552056205720582059206020612062206320642065206620672068206920702071207220732074207520762077207820792080208120822083208420852086208720882089209020912092209320942095209620972098209921002101210221032104210521062107210821092110211121122113211421152116211721182119212021212122212321242125212621272128212921302131213221332134213521362137213821392140214121422143214421452146214721482149215021512152215321542155215621572158215921602161216221632164216521662167216821692170217121722173217421752176217721782179218021812182218321842185218621872188218921902191219221932194219521962197219821992200220122022203220422052206220722082209221022112212221322142215221622172218
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #define CONFIGURATION_H_VERSION 020000
  39. //===========================================================================
  40. //============================= Getting Started =============================
  41. //===========================================================================
  42. /**
  43. * Here are some standard links for getting your machine calibrated:
  44. *
  45. * http://reprap.org/wiki/Calibration
  46. * http://youtu.be/wAL9d7FgInk
  47. * http://calculator.josefprusa.cz
  48. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  49. * http://www.thingiverse.com/thing:5573
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * http://www.thingiverse.com/thing:298812
  52. */
  53. //===========================================================================
  54. //============================= DELTA Printer ===============================
  55. //===========================================================================
  56. // For a Delta printer start with one of the configuration files in the
  57. // config/examples/delta directory and customize for your machine.
  58. //
  59. //===========================================================================
  60. //============================= SCARA Printer ===============================
  61. //===========================================================================
  62. // For a SCARA printer start with the configuration files in
  63. // config/examples/SCARA and customize for your machine.
  64. //
  65. // @section info
  66. // Author info of this build printed to the host during boot and M115
  67. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  68. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  69. /**
  70. * *** VENDORS PLEASE READ ***
  71. *
  72. * Marlin allows you to add a custom boot image for Graphical LCDs.
  73. * With this option Marlin will first show your custom screen followed
  74. * by the standard Marlin logo with version number and web URL.
  75. *
  76. * We encourage you to take advantage of this new feature and we also
  77. * respectfully request that you retain the unmodified Marlin boot screen.
  78. */
  79. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  80. #define SHOW_BOOTSCREEN
  81. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  82. #define SHOW_CUSTOM_BOOTSCREEN
  83. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  84. //#define CUSTOM_STATUS_SCREEN_IMAGE
  85. // @section machine
  86. /**
  87. * Select the serial port on the board to use for communication with the host.
  88. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT 0
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  97. * Serial port -1 is the USB emulated serial port, if available.
  98. *
  99. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  100. */
  101. //#define SERIAL_PORT_2 -1
  102. /**
  103. * This setting determines the communication speed of the printer.
  104. *
  105. * 250000 works in most cases, but you might try a lower speed if
  106. * you commonly experience drop-outs during host printing.
  107. * You may try up to 1000000 to speed up SD file transfer.
  108. *
  109. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  110. */
  111. #define BAUDRATE 115200
  112. // Enable the Bluetooth serial interface on AT90USB devices
  113. //#define BLUETOOTH
  114. // Choose the name from boards.h that matches your setup
  115. #ifndef MOTHERBOARD
  116. #define MOTHERBOARD BOARD_VORON
  117. #endif
  118. // Name displayed in the LCD "Ready" message and Info menu
  119. #define CUSTOM_MACHINE_NAME "VORON 2.0"
  120. // Printer's unique ID, used by some programs to differentiate between machines.
  121. // Choose your own or use a service like http://www.uuidgenerator.net/version4
  122. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  123. // @section extruder
  124. // This defines the number of extruders
  125. // :[1, 2, 3, 4, 5, 6]
  126. #define EXTRUDERS 2
  127. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  128. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  129. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  130. //#define SINGLENOZZLE
  131. /**
  132. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  133. *
  134. * This device allows one stepper driver on a control board to drive
  135. * two to eight stepper motors, one at a time, in a manner suitable
  136. * for extruders.
  137. *
  138. * This option only allows the multiplexer to switch on tool-change.
  139. * Additional options to configure custom E moves are pending.
  140. */
  141. //#define MK2_MULTIPLEXER
  142. #if ENABLED(MK2_MULTIPLEXER)
  143. // Override the default DIO selector pins here, if needed.
  144. // Some pins files may provide defaults for these pins.
  145. //#define E_MUX0_PIN 40 // Always Required
  146. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  147. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  148. #endif
  149. /**
  150. * Prusa Multi-Material Unit v2
  151. *
  152. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  153. * Requires EXTRUDERS = 5
  154. *
  155. * For additional configuration see Configuration_adv.h
  156. */
  157. //#define PRUSA_MMU2
  158. // A dual extruder that uses a single stepper motor
  159. //#define SWITCHING_EXTRUDER
  160. #if ENABLED(SWITCHING_EXTRUDER)
  161. #define SWITCHING_EXTRUDER_SERVO_NR 0
  162. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  163. #if EXTRUDERS > 3
  164. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  165. #endif
  166. #endif
  167. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  168. //#define SWITCHING_NOZZLE
  169. #if ENABLED(SWITCHING_NOZZLE)
  170. #define SWITCHING_NOZZLE_SERVO_NR 0
  171. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  172. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  173. #endif
  174. /**
  175. * Two separate X-carriages with extruders that connect to a moving part
  176. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  177. */
  178. //#define PARKING_EXTRUDER
  179. /**
  180. * Two separate X-carriages with extruders that connect to a moving part
  181. * via a magnetic docking mechanism using movements and no solenoid
  182. *
  183. * project : https://www.thingiverse.com/thing:3080893
  184. * movements : https://youtu.be/0xCEiG9VS3k
  185. * https://youtu.be/Bqbcs0CU2FE
  186. */
  187. //#define MAGNETIC_PARKING_EXTRUDER
  188. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  189. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  190. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  191. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  192. #if ENABLED(PARKING_EXTRUDER)
  193. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  194. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  195. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  196. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  197. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  198. #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
  199. #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
  200. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  201. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  202. #endif
  203. #endif
  204. /**
  205. * Switching Toolhead
  206. *
  207. * Support for swappable and dockable toolheads, such as
  208. * the E3D Tool Changer. Toolheads are locked with a servo.
  209. */
  210. //#define SWITCHING_TOOLHEAD
  211. /**
  212. * Magnetic Switching Toolhead
  213. *
  214. * Support swappable and dockable toolheads with a magnetic
  215. * docking mechanism using movement and no servo.
  216. */
  217. //#define MAGNETIC_SWITCHING_TOOLHEAD
  218. /**
  219. * Electromagnetic Switching Toolhead
  220. *
  221. * Parking for CoreXY / HBot kinematics.
  222. * Toolheads are parked at one edge and held with an electromagnet.
  223. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  224. */
  225. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  226. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  227. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  228. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  229. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  230. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  231. #if ENABLED(SWITCHING_TOOLHEAD)
  232. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  233. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  234. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  235. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  236. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  237. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  238. #if ENABLED(PRIME_BEFORE_REMOVE)
  239. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  240. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  241. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate
  242. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate
  243. #endif
  244. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  245. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  246. #endif
  247. #endif
  248. /**
  249. * "Mixing Extruder"
  250. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  251. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  252. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  253. * - This implementation supports up to two mixing extruders.
  254. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  255. */
  256. //#define MIXING_EXTRUDER
  257. #if ENABLED(MIXING_EXTRUDER)
  258. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  259. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  260. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  261. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  262. #if ENABLED(GRADIENT_MIX)
  263. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  264. #endif
  265. #endif
  266. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  267. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  268. // For the other hotends it is their distance from the extruder 0 hotend.
  269. #define HOTEND_OFFSET_X { 0.0, -18.00 } // (mm) relative X-offset for each nozzle
  270. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  271. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  272. // @section machine
  273. /**
  274. * Power Supply Control
  275. *
  276. * Enable and connect the power supply to the PS_ON_PIN.
  277. * Specify whether the power supply is active HIGH or active LOW.
  278. */
  279. //#define PSU_CONTROL
  280. //#define PSU_NAME "Power Supply"
  281. #if ENABLED(PSU_CONTROL)
  282. #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
  283. //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80
  284. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  285. #if ENABLED(AUTO_POWER_CONTROL)
  286. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  287. #define AUTO_POWER_E_FANS
  288. #define AUTO_POWER_CONTROLLERFAN
  289. #define AUTO_POWER_CHAMBER_FAN
  290. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature
  291. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature
  292. #define POWER_TIMEOUT 30
  293. #endif
  294. #endif
  295. // @section temperature
  296. //===========================================================================
  297. //============================= Thermal Settings ============================
  298. //===========================================================================
  299. /**
  300. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  301. *
  302. * Temperature sensors available:
  303. *
  304. * -4 : thermocouple with AD8495
  305. * -3 : thermocouple with MAX31855 (only for sensor 0)
  306. * -2 : thermocouple with MAX6675 (only for sensor 0)
  307. * -1 : thermocouple with AD595
  308. * 0 : not used
  309. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  310. * 331 : (3.3V scaled thermistor 1 table)
  311. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  312. * 3 : Mendel-parts thermistor (4.7k pullup)
  313. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  314. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  315. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  316. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  317. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  318. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  319. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  320. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  321. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  322. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  323. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  324. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  325. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  326. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  327. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  328. * 20 : Pt100 with circuit in the Ultimainboard V2.x
  329. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  330. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  331. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  332. * 66 : 4.7M High Temperature thermistor from Dyze Design
  333. * 67 : 450C thermistor from SliceEngineering
  334. * 70 : the 100K thermistor found in the bq Hephestos 2
  335. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  336. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  337. *
  338. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  339. * (but gives greater accuracy and more stable PID)
  340. * 51 : 100k thermistor - EPCOS (1k pullup)
  341. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  342. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  343. *
  344. * 1047 : Pt1000 with 4k7 pullup
  345. * 1010 : Pt1000 with 1k pullup (non standard)
  346. * 147 : Pt100 with 4k7 pullup
  347. * 110 : Pt100 with 1k pullup (non standard)
  348. *
  349. * 1000 : Custom - Specify parameters in Configuration_adv.h
  350. *
  351. * Use these for Testing or Development purposes. NEVER for production machine.
  352. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  353. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  354. */
  355. #define TEMP_SENSOR_0 5
  356. #define TEMP_SENSOR_1 5
  357. #define TEMP_SENSOR_2 0
  358. #define TEMP_SENSOR_3 0
  359. #define TEMP_SENSOR_4 0
  360. #define TEMP_SENSOR_5 0
  361. #define TEMP_SENSOR_BED 1
  362. #define TEMP_SENSOR_CHAMBER 0
  363. // Dummy thermistor constant temperature readings, for use with 998 and 999
  364. #define DUMMY_THERMISTOR_998_VALUE 25
  365. #define DUMMY_THERMISTOR_999_VALUE 100
  366. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  367. // from the two sensors differ too much the print will be aborted.
  368. //#define TEMP_SENSOR_1_AS_REDUNDANT
  369. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  370. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  371. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  372. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  373. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  374. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  375. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  376. // Below this temperature the heater will be switched off
  377. // because it probably indicates a broken thermistor wire.
  378. #define HEATER_0_MINTEMP 5
  379. #define HEATER_1_MINTEMP 5
  380. #define HEATER_2_MINTEMP 5
  381. #define HEATER_3_MINTEMP 5
  382. #define HEATER_4_MINTEMP 5
  383. #define HEATER_5_MINTEMP 5
  384. #define BED_MINTEMP 5
  385. // Above this temperature the heater will be switched off.
  386. // This can protect components from overheating, but NOT from shorts and failures.
  387. // (Use MINTEMP for thermistor short/failure protection.)
  388. #define HEATER_0_MAXTEMP 275
  389. #define HEATER_1_MAXTEMP 275
  390. #define HEATER_2_MAXTEMP 275
  391. #define HEATER_3_MAXTEMP 275
  392. #define HEATER_4_MAXTEMP 275
  393. #define HEATER_5_MAXTEMP 275
  394. #define BED_MAXTEMP 150
  395. //===========================================================================
  396. //============================= PID Settings ================================
  397. //===========================================================================
  398. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  399. // Comment the following line to disable PID and enable bang-bang.
  400. #define PIDTEMP
  401. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  402. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  403. #define PID_K1 0.95 // Smoothing factor within any PID loop
  404. #if ENABLED(PIDTEMP)
  405. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  406. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  407. //#define PID_DEBUG // Sends debug data to the serial port.
  408. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  409. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  410. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  411. // Set/get with gcode: M301 E[extruder number, 0-2]
  412. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  413. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  414. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  415. // Ultimaker
  416. //#define DEFAULT_Kp 22.2
  417. //#define DEFAULT_Ki 1.08
  418. //#define DEFAULT_Kd 114
  419. // MakerGear
  420. //#define DEFAULT_Kp 7.0
  421. //#define DEFAULT_Ki 0.1
  422. //#define DEFAULT_Kd 12
  423. // Mendel Parts V9 on 12V
  424. //#define DEFAULT_Kp 63.0
  425. //#define DEFAULT_Ki 2.25
  426. //#define DEFAULT_Kd 440
  427. // from VORON
  428. #define DEFAULT_Kp 23.72
  429. #define DEFAULT_Ki 1.56
  430. #define DEFAULT_Kd 90.34
  431. #endif // PIDTEMP
  432. //===========================================================================
  433. //====================== PID > Bed Temperature Control ======================
  434. //===========================================================================
  435. /**
  436. * PID Bed Heating
  437. *
  438. * If this option is enabled set PID constants below.
  439. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  440. *
  441. * The PID frequency will be the same as the extruder PWM.
  442. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  443. * which is fine for driving a square wave into a resistive load and does not significantly
  444. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  445. * heater. If your configuration is significantly different than this and you don't understand
  446. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  447. */
  448. //#define PIDTEMPBED
  449. //#define BED_LIMIT_SWITCHING
  450. /**
  451. * Max Bed Power
  452. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  453. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  454. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  455. */
  456. #define MAX_BED_POWER 205 // limits duty cycle to bed; 255=full current
  457. #if ENABLED(PIDTEMPBED)
  458. //#define MIN_BED_POWER 0
  459. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  460. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  461. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  462. //#define DEFAULT_bedKp 10.00
  463. //#define DEFAULT_bedKi .023
  464. //#define DEFAULT_bedKd 305.4
  465. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  466. //from pidautotune
  467. //#define DEFAULT_bedKp 97.1
  468. //#define DEFAULT_bedKi 1.41
  469. //#define DEFAULT_bedKd 1675.16
  470. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  471. // Results from VORON
  472. #define DEFAULT_bedKp 150.52
  473. #define DEFAULT_bedKi 12.25
  474. #define DEFAULT_bedKd 462.40
  475. #endif // PIDTEMPBED
  476. // @section extruder
  477. /**
  478. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  479. * Add M302 to set the minimum extrusion temperature and/or turn
  480. * cold extrusion prevention on and off.
  481. *
  482. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  483. */
  484. #define PREVENT_COLD_EXTRUSION
  485. #define EXTRUDE_MINTEMP 170
  486. /**
  487. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  488. * Note: For Bowden Extruders make this large enough to allow load/unload.
  489. */
  490. #define PREVENT_LENGTHY_EXTRUDE
  491. #define EXTRUDE_MAXLENGTH 200
  492. //===========================================================================
  493. //======================== Thermal Runaway Protection =======================
  494. //===========================================================================
  495. /**
  496. * Thermal Protection provides additional protection to your printer from damage
  497. * and fire. Marlin always includes safe min and max temperature ranges which
  498. * protect against a broken or disconnected thermistor wire.
  499. *
  500. * The issue: If a thermistor falls out, it will report the much lower
  501. * temperature of the air in the room, and the the firmware will keep
  502. * the heater on.
  503. *
  504. * If you get "Thermal Runaway" or "Heating failed" errors the
  505. * details can be tuned in Configuration_adv.h
  506. */
  507. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  508. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  509. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  510. //===========================================================================
  511. //============================= Mechanical Settings =========================
  512. //===========================================================================
  513. // @section machine
  514. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  515. // either in the usual order or reversed
  516. #define COREXY
  517. //#define COREXZ
  518. //#define COREYZ
  519. //#define COREYX
  520. //#define COREZX
  521. //#define COREZY
  522. //===========================================================================
  523. //============================== Endstop Settings ===========================
  524. //===========================================================================
  525. // @section homing
  526. // Specify here all the endstop connectors that are connected to any endstop or probe.
  527. // Almost all printers will be using one per axis. Probes will use one or more of the
  528. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  529. #define USE_XMIN_PLUG
  530. #define USE_YMIN_PLUG
  531. #define USE_ZMIN_PLUG
  532. //#define USE_XMAX_PLUG
  533. //#define USE_YMAX_PLUG
  534. //#define USE_ZMAX_PLUG
  535. // Enable pullup for all endstops to prevent a floating state
  536. #define ENDSTOPPULLUPS
  537. #if DISABLED(ENDSTOPPULLUPS)
  538. // Disable ENDSTOPPULLUPS to set pullups individually
  539. #define ENDSTOPPULLUP_XMAX
  540. #define ENDSTOPPULLUP_YMAX
  541. #define ENDSTOPPULLUP_ZMAX
  542. #define ENDSTOPPULLUP_XMIN
  543. #define ENDSTOPPULLUP_YMIN
  544. #define ENDSTOPPULLUP_ZMIN
  545. #define ENDSTOPPULLUP_ZMIN_PROBE
  546. #endif
  547. // Enable pulldown for all endstops to prevent a floating state
  548. //#define ENDSTOPPULLDOWNS
  549. #if DISABLED(ENDSTOPPULLDOWNS)
  550. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  551. //#define ENDSTOPPULLDOWN_XMAX
  552. //#define ENDSTOPPULLDOWN_YMAX
  553. //#define ENDSTOPPULLDOWN_ZMAX
  554. //#define ENDSTOPPULLDOWN_XMIN
  555. //#define ENDSTOPPULLDOWN_YMIN
  556. //#define ENDSTOPPULLDOWN_ZMIN
  557. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  558. #endif
  559. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  560. #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  561. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  562. #define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  563. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  564. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  565. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  566. #define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
  567. /**
  568. * Stepper Drivers
  569. *
  570. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  571. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  572. *
  573. * A4988 is assumed for unspecified drivers.
  574. *
  575. * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  576. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  577. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  578. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  579. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  580. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  581. */
  582. #define X_DRIVER_TYPE DRV8825
  583. #define Y_DRIVER_TYPE DRV8825
  584. #define Z_DRIVER_TYPE DRV8825
  585. //#define X2_DRIVER_TYPE A4988
  586. //#define Y2_DRIVER_TYPE A4988
  587. //#define Z2_DRIVER_TYPE A4988
  588. //#define Z3_DRIVER_TYPE A4988
  589. #define E0_DRIVER_TYPE DRV8825
  590. #define E1_DRIVER_TYPE DRV8825
  591. //#define E2_DRIVER_TYPE A4988
  592. //#define E3_DRIVER_TYPE A4988
  593. //#define E4_DRIVER_TYPE A4988
  594. //#define E5_DRIVER_TYPE A4988
  595. // Enable this feature if all enabled endstop pins are interrupt-capable.
  596. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  597. //#define ENDSTOP_INTERRUPTS_FEATURE
  598. /**
  599. * Endstop Noise Threshold
  600. *
  601. * Enable if your probe or endstops falsely trigger due to noise.
  602. *
  603. * - Higher values may affect repeatability or accuracy of some bed probes.
  604. * - To fix noise install a 100nF ceramic capacitor inline with the switch.
  605. * - This feature is not required for common micro-switches mounted on PCBs
  606. * based on the Makerbot design, which already have the 100nF capacitor.
  607. *
  608. * :[2,3,4,5,6,7]
  609. */
  610. //#define ENDSTOP_NOISE_THRESHOLD 2
  611. //=============================================================================
  612. //============================== Movement Settings ============================
  613. //=============================================================================
  614. // @section motion
  615. /**
  616. * Default Settings
  617. *
  618. * These settings can be reset by M502
  619. *
  620. * Note that if EEPROM is enabled, saved values will override these.
  621. */
  622. /**
  623. * With this option each E stepper can have its own factors for the
  624. * following movement settings. If fewer factors are given than the
  625. * total number of extruders, the last value applies to the rest.
  626. */
  627. #define DISTINCT_E_FACTORS
  628. /**
  629. * Default Axis Steps Per Unit (steps/mm)
  630. * Override with M92
  631. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  632. */
  633. #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 608, 608 }
  634. /**
  635. * Default Max Feed Rate (mm/s)
  636. * Override with M203
  637. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  638. */
  639. #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 75, 75 }
  640. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  641. #if ENABLED(LIMITED_MAX_FR_EDITING)
  642. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  643. #endif
  644. /**
  645. * Default Max Acceleration (change/s) change = mm/s
  646. * (Maximum start speed for accelerated moves)
  647. * Override with M201
  648. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  649. */
  650. #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 , 10000 }
  651. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  652. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  653. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  654. #endif
  655. /**
  656. * Default Acceleration (change/s) change = mm/s
  657. * Override with M204
  658. *
  659. * M204 P Acceleration
  660. * M204 R Retract Acceleration
  661. * M204 T Travel Acceleration
  662. */
  663. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  664. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  665. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  666. /**
  667. * Default Jerk limits (mm/s)
  668. * Override with M205 X Y Z E
  669. *
  670. * "Jerk" specifies the minimum speed change that requires acceleration.
  671. * When changing speed and direction, if the difference is less than the
  672. * value set here, it may happen instantaneously.
  673. */
  674. //#define CLASSIC_JERK
  675. #if ENABLED(CLASSIC_JERK)
  676. #define DEFAULT_XJERK 20.0
  677. #define DEFAULT_YJERK 15.0
  678. #define DEFAULT_ZJERK 0.4
  679. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  680. #if ENABLED(LIMITED_JERK_EDITING)
  681. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  682. #endif
  683. #endif
  684. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  685. /**
  686. * Junction Deviation Factor
  687. *
  688. * See:
  689. * https://reprap.org/forum/read.php?1,739819
  690. * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  691. */
  692. #if DISABLED(CLASSIC_JERK)
  693. #define JUNCTION_DEVIATION_MM 0.03 // (mm) Distance from real junction edge
  694. #endif
  695. /**
  696. * S-Curve Acceleration
  697. *
  698. * This option eliminates vibration during printing by fitting a Bézier
  699. * curve to move acceleration, producing much smoother direction changes.
  700. *
  701. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  702. */
  703. //#define S_CURVE_ACCELERATION
  704. //===========================================================================
  705. //============================= Z Probe Options =============================
  706. //===========================================================================
  707. // @section probes
  708. //
  709. // See http://marlinfw.org/docs/configuration/probes.html
  710. //
  711. /**
  712. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  713. *
  714. * Enable this option for a probe connected to the Z Min endstop pin.
  715. */
  716. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  717. /**
  718. * Z_MIN_PROBE_PIN
  719. *
  720. * Define this pin if the probe is not connected to Z_MIN_PIN.
  721. * If not defined the default pin for the selected MOTHERBOARD
  722. * will be used. Most of the time the default is what you want.
  723. *
  724. * - The simplest option is to use a free endstop connector.
  725. * - Use 5V for powered (usually inductive) sensors.
  726. *
  727. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  728. * - For simple switches connect...
  729. * - normally-closed switches to GND and D32.
  730. * - normally-open switches to 5V and D32.
  731. *
  732. */
  733. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  734. /**
  735. * Probe Type
  736. *
  737. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  738. * Activate one of these to use Auto Bed Leveling below.
  739. */
  740. /**
  741. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  742. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  743. * or (with LCD_BED_LEVELING) the LCD controller.
  744. */
  745. //#define PROBE_MANUALLY
  746. //#define MANUAL_PROBE_START_Z 0.2
  747. /**
  748. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  749. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  750. */
  751. #define FIX_MOUNTED_PROBE
  752. /**
  753. * Z Servo Probe, such as an endstop switch on a rotating arm.
  754. */
  755. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  756. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  757. /**
  758. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  759. */
  760. //#define BLTOUCH
  761. /**
  762. * Touch-MI Probe by hotends.fr
  763. *
  764. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  765. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  766. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  767. *
  768. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  769. * and a minimum Z_HOMING_HEIGHT of 10.
  770. */
  771. //#define TOUCH_MI_PROBE
  772. #if ENABLED(TOUCH_MI_PROBE)
  773. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  774. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  775. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  776. #endif
  777. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  778. //#define SOLENOID_PROBE
  779. // A sled-mounted probe like those designed by Charles Bell.
  780. //#define Z_PROBE_SLED
  781. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  782. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  783. //#define RACK_AND_PINION_PROBE
  784. #if ENABLED(RACK_AND_PINION_PROBE)
  785. #define Z_PROBE_DEPLOY_X X_MIN_POS
  786. #define Z_PROBE_RETRACT_X X_MAX_POS
  787. #endif
  788. //
  789. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  790. //
  791. /**
  792. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  793. *
  794. * In the following example the X and Y offsets are both positive:
  795. *
  796. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  797. *
  798. * +-- BACK ---+
  799. * | |
  800. * L | (+) P | R <-- probe (20,20)
  801. * E | | I
  802. * F | (-) N (+) | G <-- nozzle (10,10)
  803. * T | | H
  804. * | (-) | T
  805. * | |
  806. * O-- FRONT --+
  807. * (0,0)
  808. *
  809. * Specify a Probe position as { X, Y, Z }
  810. */
  811. #define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
  812. // Certain types of probes need to stay away from edges
  813. #define MIN_PROBE_EDGE 10
  814. // X and Y axis travel speed (mm/m) between probes
  815. #define XY_PROBE_SPEED 8000
  816. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  817. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  818. // Feedrate (mm/m) for the "accurate" probe of each point
  819. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  820. /**
  821. * Multiple Probing
  822. *
  823. * You may get improved results by probing 2 or more times.
  824. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  825. *
  826. * A total of 2 does fast/slow probes with a weighted average.
  827. * A total of 3 or more adds more slow probes, taking the average.
  828. */
  829. //#define MULTIPLE_PROBING 2
  830. //#define EXTRA_PROBING 1
  831. /**
  832. * Z probes require clearance when deploying, stowing, and moving between
  833. * probe points to avoid hitting the bed and other hardware.
  834. * Servo-mounted probes require extra space for the arm to rotate.
  835. * Inductive probes need space to keep from triggering early.
  836. *
  837. * Use these settings to specify the distance (mm) to raise the probe (or
  838. * lower the bed). The values set here apply over and above any (negative)
  839. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  840. * Only integer values >= 1 are valid here.
  841. *
  842. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  843. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  844. */
  845. #define Z_CLEARANCE_DEPLOY_PROBE 0 // Z Clearance for Deploy/Stow
  846. #define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points
  847. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  848. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  849. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  850. // For M851 give a range for adjusting the Z probe offset
  851. #define Z_PROBE_OFFSET_RANGE_MIN -20
  852. #define Z_PROBE_OFFSET_RANGE_MAX 20
  853. // Enable the M48 repeatability test to test probe accuracy
  854. #define Z_MIN_PROBE_REPEATABILITY_TEST
  855. // Before deploy/stow pause for user confirmation
  856. //#define PAUSE_BEFORE_DEPLOY_STOW
  857. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  858. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  859. #endif
  860. /**
  861. * Enable one or more of the following if probing seems unreliable.
  862. * Heaters and/or fans can be disabled during probing to minimize electrical
  863. * noise. A delay can also be added to allow noise and vibration to settle.
  864. * These options are most useful for the BLTouch probe, but may also improve
  865. * readings with inductive probes and piezo sensors.
  866. */
  867. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  868. #if ENABLED(PROBING_HEATERS_OFF)
  869. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  870. #endif
  871. //#define PROBING_FANS_OFF // Turn fans off when probing
  872. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  873. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  874. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  875. // :{ 0:'Low', 1:'High' }
  876. #define X_ENABLE_ON 0
  877. #define Y_ENABLE_ON 0
  878. #define Z_ENABLE_ON 0
  879. #define E_ENABLE_ON 0 // For all extruders
  880. // Disables axis stepper immediately when it's not being used.
  881. // WARNING: When motors turn off there is a chance of losing position accuracy!
  882. #define DISABLE_X false
  883. #define DISABLE_Y false
  884. #define DISABLE_Z false
  885. // Warn on display about possibly reduced accuracy
  886. //#define DISABLE_REDUCED_ACCURACY_WARNING
  887. // @section extruder
  888. #define DISABLE_E false // For all extruders
  889. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  890. // @section machine
  891. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  892. #define INVERT_X_DIR false
  893. #define INVERT_Y_DIR false
  894. #define INVERT_Z_DIR false
  895. // @section extruder
  896. // For direct drive extruder v9 set to true, for geared extruder set to false.
  897. #define INVERT_E0_DIR false
  898. #define INVERT_E1_DIR false
  899. #define INVERT_E2_DIR false
  900. #define INVERT_E3_DIR false
  901. #define INVERT_E4_DIR false
  902. #define INVERT_E5_DIR false
  903. // @section homing
  904. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  905. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  906. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  907. // Be sure you have this distance over your Z_MAX_POS in case.
  908. // Direction of endstops when homing; 1=MAX, -1=MIN
  909. // :[-1,1]
  910. #define X_HOME_DIR -1
  911. #define Y_HOME_DIR -1
  912. #define Z_HOME_DIR -1
  913. // @section machine
  914. // The size of the print bed
  915. #define X_BED_SIZE 230
  916. #define Y_BED_SIZE 230
  917. // Travel limits (mm) after homing, corresponding to endstop positions.
  918. #define X_MIN_POS 0
  919. #define Y_MIN_POS 0
  920. #define Z_MIN_POS 0
  921. #define X_MAX_POS X_BED_SIZE
  922. #define Y_MAX_POS Y_BED_SIZE
  923. #define Z_MAX_POS 230
  924. /**
  925. * Software Endstops
  926. *
  927. * - Prevent moves outside the set machine bounds.
  928. * - Individual axes can be disabled, if desired.
  929. * - X and Y only apply to Cartesian robots.
  930. * - Use 'M211' to set software endstops on/off or report current state
  931. */
  932. // Min software endstops constrain movement within minimum coordinate bounds
  933. //#define MIN_SOFTWARE_ENDSTOPS
  934. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  935. #define MIN_SOFTWARE_ENDSTOP_X
  936. #define MIN_SOFTWARE_ENDSTOP_Y
  937. #define MIN_SOFTWARE_ENDSTOP_Z
  938. #endif
  939. // Max software endstops constrain movement within maximum coordinate bounds
  940. //#define MAX_SOFTWARE_ENDSTOPS
  941. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  942. #define MAX_SOFTWARE_ENDSTOP_X
  943. #define MAX_SOFTWARE_ENDSTOP_Y
  944. #define MAX_SOFTWARE_ENDSTOP_Z
  945. #endif
  946. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  947. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  948. #endif
  949. /**
  950. * Filament Runout Sensors
  951. * Mechanical or opto endstops are used to check for the presence of filament.
  952. *
  953. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  954. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  955. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  956. */
  957. //#define FILAMENT_RUNOUT_SENSOR
  958. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  959. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  960. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
  961. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  962. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  963. // Set one or more commands to execute on filament runout.
  964. // (After 'M412 H' Marlin will ask the host to handle the process.)
  965. #define FILAMENT_RUNOUT_SCRIPT "M600"
  966. // After a runout is detected, continue printing this length of filament
  967. // before executing the runout script. Useful for a sensor at the end of
  968. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  969. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  970. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  971. // Enable this option to use an encoder disc that toggles the runout pin
  972. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  973. // large enough to avoid false positives.)
  974. //#define FILAMENT_MOTION_SENSOR
  975. #endif
  976. #endif
  977. //===========================================================================
  978. //=============================== Bed Leveling ==============================
  979. //===========================================================================
  980. // @section calibrate
  981. /**
  982. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  983. * and behavior of G29 will change depending on your selection.
  984. *
  985. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  986. *
  987. * - AUTO_BED_LEVELING_3POINT
  988. * Probe 3 arbitrary points on the bed (that aren't collinear)
  989. * You specify the XY coordinates of all 3 points.
  990. * The result is a single tilted plane. Best for a flat bed.
  991. *
  992. * - AUTO_BED_LEVELING_LINEAR
  993. * Probe several points in a grid.
  994. * You specify the rectangle and the density of sample points.
  995. * The result is a single tilted plane. Best for a flat bed.
  996. *
  997. * - AUTO_BED_LEVELING_BILINEAR
  998. * Probe several points in a grid.
  999. * You specify the rectangle and the density of sample points.
  1000. * The result is a mesh, best for large or uneven beds.
  1001. *
  1002. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1003. * A comprehensive bed leveling system combining the features and benefits
  1004. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1005. * Validation and Mesh Editing systems.
  1006. *
  1007. * - MESH_BED_LEVELING
  1008. * Probe a grid manually
  1009. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1010. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1011. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1012. * With an LCD controller the process is guided step-by-step.
  1013. */
  1014. //#define AUTO_BED_LEVELING_3POINT
  1015. //#define AUTO_BED_LEVELING_LINEAR
  1016. //#define AUTO_BED_LEVELING_BILINEAR
  1017. #define AUTO_BED_LEVELING_UBL
  1018. //#define MESH_BED_LEVELING
  1019. /**
  1020. * Normally G28 leaves leveling disabled on completion. Enable
  1021. * this option to have G28 restore the prior leveling state.
  1022. */
  1023. #define RESTORE_LEVELING_AFTER_G28
  1024. /**
  1025. * Enable detailed logging of G28, G29, M48, etc.
  1026. * Turn on with the command 'M111 S32'.
  1027. * NOTE: Requires a lot of PROGMEM!
  1028. */
  1029. //#define DEBUG_LEVELING_FEATURE
  1030. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1031. // Gradually reduce leveling correction until a set height is reached,
  1032. // at which point movement will be level to the machine's XY plane.
  1033. // The height can be set with M420 Z<height>
  1034. #define ENABLE_LEVELING_FADE_HEIGHT
  1035. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1036. // split up moves into short segments like a Delta. This follows the
  1037. // contours of the bed more closely than edge-to-edge straight moves.
  1038. #define SEGMENT_LEVELED_MOVES
  1039. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1040. /**
  1041. * Enable the G26 Mesh Validation Pattern tool.
  1042. */
  1043. #define G26_MESH_VALIDATION
  1044. #if ENABLED(G26_MESH_VALIDATION)
  1045. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1046. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1047. #define MESH_TEST_HOTEND_TEMP 200 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1048. #define MESH_TEST_BED_TEMP 100 // (°C) Defaultbed temperature for the G26 Mesh Validation Tool.
  1049. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1050. #endif
  1051. #endif
  1052. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1053. // Set the number of grid points per dimension.
  1054. #define GRID_MAX_POINTS_X 3
  1055. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1056. // Probe along the Y axis, advancing X after each column
  1057. //#define PROBE_Y_FIRST
  1058. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1059. // Beyond the probed grid, continue the implied tilt?
  1060. // Default is to maintain the height of the nearest edge.
  1061. //#define EXTRAPOLATE_BEYOND_GRID
  1062. //
  1063. // Experimental Subdivision of the grid by Catmull-Rom method.
  1064. // Synthesizes intermediate points to produce a more detailed mesh.
  1065. //
  1066. //#define ABL_BILINEAR_SUBDIVISION
  1067. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1068. // Number of subdivisions between probe points
  1069. #define BILINEAR_SUBDIVISIONS 3
  1070. #endif
  1071. #endif
  1072. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1073. //===========================================================================
  1074. //========================= Unified Bed Leveling ============================
  1075. //===========================================================================
  1076. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1077. #define MESH_INSET 15 // Set Mesh bounds as an inset region of the bed
  1078. #define GRID_MAX_POINTS_X 12 // Don't use more than 15 points per axis, implementation limited.
  1079. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1080. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1081. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1082. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1083. // as the Z-Height correction value.
  1084. #elif ENABLED(MESH_BED_LEVELING)
  1085. //===========================================================================
  1086. //=================================== Mesh ==================================
  1087. //===========================================================================
  1088. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1089. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1090. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1091. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1092. #endif // BED_LEVELING
  1093. /**
  1094. * Add a bed leveling sub-menu for ABL or MBL.
  1095. * Include a guided procedure if manual probing is enabled.
  1096. */
  1097. //#define LCD_BED_LEVELING
  1098. #if ENABLED(LCD_BED_LEVELING)
  1099. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1100. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1101. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1102. #endif
  1103. // Add a menu item to move between bed corners for manual bed adjustment
  1104. #define LEVEL_BED_CORNERS
  1105. #if ENABLED(LEVEL_BED_CORNERS)
  1106. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1107. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
  1108. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1109. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1110. #endif
  1111. /**
  1112. * Commands to execute at the end of G29 probing.
  1113. * Useful to retract or move the Z probe out of the way.
  1114. */
  1115. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1116. // @section homing
  1117. // The center of the bed is at (X=0, Y=0)
  1118. //#define BED_CENTER_AT_0_0
  1119. // Manually set the home position. Leave these undefined for automatic settings.
  1120. // For DELTA this is the top-center of the Cartesian print volume.
  1121. //#define MANUAL_X_HOME_POS 0
  1122. //#define MANUAL_Y_HOME_POS 0
  1123. //#define MANUAL_Z_HOME_POS 0
  1124. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1125. //
  1126. // With this feature enabled:
  1127. //
  1128. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1129. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1130. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1131. // - Prevent Z homing when the Z probe is outside bed area.
  1132. //
  1133. #define Z_SAFE_HOMING
  1134. #if ENABLED(Z_SAFE_HOMING)
  1135. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1136. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1137. #endif
  1138. // Homing speeds (mm/m)
  1139. #define HOMING_FEEDRATE_XY (50*60)
  1140. #define HOMING_FEEDRATE_Z (4*60)
  1141. // Validate that endstops are triggered on homing moves
  1142. #define VALIDATE_HOMING_ENDSTOPS
  1143. // @section calibrate
  1144. /**
  1145. * Bed Skew Compensation
  1146. *
  1147. * This feature corrects for misalignment in the XYZ axes.
  1148. *
  1149. * Take the following steps to get the bed skew in the XY plane:
  1150. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1151. * 2. For XY_DIAG_AC measure the diagonal A to C
  1152. * 3. For XY_DIAG_BD measure the diagonal B to D
  1153. * 4. For XY_SIDE_AD measure the edge A to D
  1154. *
  1155. * Marlin automatically computes skew factors from these measurements.
  1156. * Skew factors may also be computed and set manually:
  1157. *
  1158. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1159. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1160. *
  1161. * If desired, follow the same procedure for XZ and YZ.
  1162. * Use these diagrams for reference:
  1163. *
  1164. * Y Z Z
  1165. * ^ B-------C ^ B-------C ^ B-------C
  1166. * | / / | / / | / /
  1167. * | / / | / / | / /
  1168. * | A-------D | A-------D | A-------D
  1169. * +-------------->X +-------------->X +-------------->Y
  1170. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1171. */
  1172. //#define SKEW_CORRECTION
  1173. #if ENABLED(SKEW_CORRECTION)
  1174. // Input all length measurements here:
  1175. #define XY_DIAG_AC 282.8427124746
  1176. #define XY_DIAG_BD 282.8427124746
  1177. #define XY_SIDE_AD 200
  1178. // Or, set the default skew factors directly here
  1179. // to override the above measurements:
  1180. #define XY_SKEW_FACTOR 0.0
  1181. //#define SKEW_CORRECTION_FOR_Z
  1182. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1183. #define XZ_DIAG_AC 282.8427124746
  1184. #define XZ_DIAG_BD 282.8427124746
  1185. #define YZ_DIAG_AC 282.8427124746
  1186. #define YZ_DIAG_BD 282.8427124746
  1187. #define YZ_SIDE_AD 200
  1188. #define XZ_SKEW_FACTOR 0.0
  1189. #define YZ_SKEW_FACTOR 0.0
  1190. #endif
  1191. // Enable this option for M852 to set skew at runtime
  1192. //#define SKEW_CORRECTION_GCODE
  1193. #endif
  1194. //=============================================================================
  1195. //============================= Additional Features ===========================
  1196. //=============================================================================
  1197. // @section extras
  1198. /**
  1199. * EEPROM
  1200. *
  1201. * Persistent storage to preserve configurable settings across reboots.
  1202. *
  1203. * M500 - Store settings to EEPROM.
  1204. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1205. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1206. */
  1207. #define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1208. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1209. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1210. #if ENABLED(EEPROM_SETTINGS)
  1211. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1212. #endif
  1213. //
  1214. // Host Keepalive
  1215. //
  1216. // When enabled Marlin will send a busy status message to the host
  1217. // every couple of seconds when it can't accept commands.
  1218. //
  1219. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1220. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1221. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1222. //
  1223. // M100 Free Memory Watcher
  1224. //
  1225. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1226. //
  1227. // G20/G21 Inch mode support
  1228. //
  1229. //#define INCH_MODE_SUPPORT
  1230. //
  1231. // M149 Set temperature units support
  1232. //
  1233. //#define TEMPERATURE_UNITS_SUPPORT
  1234. // @section temperature
  1235. // Preheat Constants
  1236. #define PREHEAT_1_LABEL "PLA"
  1237. #define PREHEAT_1_TEMP_HOTEND 180
  1238. #define PREHEAT_1_TEMP_BED 70
  1239. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1240. #define PREHEAT_2_LABEL "ABS"
  1241. #define PREHEAT_2_TEMP_HOTEND 240
  1242. #define PREHEAT_2_TEMP_BED 110
  1243. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1244. /**
  1245. * Nozzle Park
  1246. *
  1247. * Park the nozzle at the given XYZ position on idle or G27.
  1248. *
  1249. * The "P" parameter controls the action applied to the Z axis:
  1250. *
  1251. * P0 (Default) If Z is below park Z raise the nozzle.
  1252. * P1 Raise the nozzle always to Z-park height.
  1253. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1254. */
  1255. //#define NOZZLE_PARK_FEATURE
  1256. #if ENABLED(NOZZLE_PARK_FEATURE)
  1257. // Specify a park position as { X, Y, Z_raise }
  1258. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1259. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1260. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1261. #endif
  1262. /**
  1263. * Clean Nozzle Feature -- EXPERIMENTAL
  1264. *
  1265. * Adds the G12 command to perform a nozzle cleaning process.
  1266. *
  1267. * Parameters:
  1268. * P Pattern
  1269. * S Strokes / Repetitions
  1270. * T Triangles (P1 only)
  1271. *
  1272. * Patterns:
  1273. * P0 Straight line (default). This process requires a sponge type material
  1274. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1275. * between the start / end points.
  1276. *
  1277. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1278. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1279. * Zig-zags are done in whichever is the narrower dimension.
  1280. * For example, "G12 P1 S1 T3" will execute:
  1281. *
  1282. * --
  1283. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1284. * | | / \ / \ / \ |
  1285. * A | | / \ / \ / \ |
  1286. * | | / \ / \ / \ |
  1287. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1288. * -- +--------------------------------+
  1289. * |________|_________|_________|
  1290. * T1 T2 T3
  1291. *
  1292. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1293. * "R" specifies the radius. "S" specifies the stroke count.
  1294. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1295. *
  1296. * Caveats: The ending Z should be the same as starting Z.
  1297. * Attention: EXPERIMENTAL. G-code arguments may change.
  1298. *
  1299. */
  1300. //#define NOZZLE_CLEAN_FEATURE
  1301. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1302. // Default number of pattern repetitions
  1303. #define NOZZLE_CLEAN_STROKES 12
  1304. // Default number of triangles
  1305. #define NOZZLE_CLEAN_TRIANGLES 3
  1306. // Specify positions as { X, Y, Z }
  1307. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1) }
  1308. #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) }
  1309. // Circular pattern radius
  1310. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1311. // Circular pattern circle fragments number
  1312. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1313. // Middle point of circle
  1314. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1315. // Move the nozzle to the initial position after cleaning
  1316. #define NOZZLE_CLEAN_GOBACK
  1317. // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
  1318. //#define NOZZLE_CLEAN_NO_Z
  1319. #endif
  1320. /**
  1321. * Print Job Timer
  1322. *
  1323. * Automatically start and stop the print job timer on M104/M109/M190.
  1324. *
  1325. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1326. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1327. * M190 (bed, wait) - high temp = start timer, low temp = none
  1328. *
  1329. * The timer can also be controlled with the following commands:
  1330. *
  1331. * M75 - Start the print job timer
  1332. * M76 - Pause the print job timer
  1333. * M77 - Stop the print job timer
  1334. */
  1335. #define PRINTJOB_TIMER_AUTOSTART
  1336. /**
  1337. * Print Counter
  1338. *
  1339. * Track statistical data such as:
  1340. *
  1341. * - Total print jobs
  1342. * - Total successful print jobs
  1343. * - Total failed print jobs
  1344. * - Total time printing
  1345. *
  1346. * View the current statistics with M78.
  1347. */
  1348. //#define PRINTCOUNTER
  1349. //=============================================================================
  1350. //============================= LCD and SD support ============================
  1351. //=============================================================================
  1352. // @section lcd
  1353. /**
  1354. * LCD LANGUAGE
  1355. *
  1356. * Select the language to display on the LCD. These languages are available:
  1357. *
  1358. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
  1359. * ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1360. *
  1361. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1362. */
  1363. #define LCD_LANGUAGE en
  1364. /**
  1365. * LCD Character Set
  1366. *
  1367. * Note: This option is NOT applicable to Graphical Displays.
  1368. *
  1369. * All character-based LCDs provide ASCII plus one of these
  1370. * language extensions:
  1371. *
  1372. * - JAPANESE ... the most common
  1373. * - WESTERN ... with more accented characters
  1374. * - CYRILLIC ... for the Russian language
  1375. *
  1376. * To determine the language extension installed on your controller:
  1377. *
  1378. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1379. * - Click the controller to view the LCD menu
  1380. * - The LCD will display Japanese, Western, or Cyrillic text
  1381. *
  1382. * See http://marlinfw.org/docs/development/lcd_language.html
  1383. *
  1384. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1385. */
  1386. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1387. /**
  1388. * Info Screen Style (0:Classic, 1:Prusa)
  1389. *
  1390. * :[0:'Classic', 1:'Prusa']
  1391. */
  1392. #define LCD_INFO_SCREEN_STYLE 0
  1393. /**
  1394. * SD CARD
  1395. *
  1396. * SD Card support is disabled by default. If your controller has an SD slot,
  1397. * you must uncomment the following option or it won't work.
  1398. *
  1399. */
  1400. #define SDSUPPORT
  1401. /**
  1402. * SD CARD: SPI SPEED
  1403. *
  1404. * Enable one of the following items for a slower SPI transfer speed.
  1405. * This may be required to resolve "volume init" errors.
  1406. */
  1407. //#define SPI_SPEED SPI_HALF_SPEED
  1408. //#define SPI_SPEED SPI_QUARTER_SPEED
  1409. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1410. /**
  1411. * SD CARD: ENABLE CRC
  1412. *
  1413. * Use CRC checks and retries on the SD communication.
  1414. */
  1415. #define SD_CHECK_AND_RETRY
  1416. /**
  1417. * LCD Menu Items
  1418. *
  1419. * Disable all menus and only display the Status Screen, or
  1420. * just remove some extraneous menu items to recover space.
  1421. */
  1422. //#define NO_LCD_MENUS
  1423. //#define SLIM_LCD_MENUS
  1424. //
  1425. // ENCODER SETTINGS
  1426. //
  1427. // This option overrides the default number of encoder pulses needed to
  1428. // produce one step. Should be increased for high-resolution encoders.
  1429. //
  1430. #define ENCODER_PULSES_PER_STEP 2
  1431. //
  1432. // Use this option to override the number of step signals required to
  1433. // move between next/prev menu items.
  1434. //
  1435. #define ENCODER_STEPS_PER_MENU_ITEM 1
  1436. /**
  1437. * Encoder Direction Options
  1438. *
  1439. * Test your encoder's behavior first with both options disabled.
  1440. *
  1441. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1442. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1443. * Reversed Value Editing only? Enable BOTH options.
  1444. */
  1445. //
  1446. // This option reverses the encoder direction everywhere.
  1447. //
  1448. // Set this option if CLOCKWISE causes values to DECREASE
  1449. //
  1450. //#define REVERSE_ENCODER_DIRECTION
  1451. //
  1452. // This option reverses the encoder direction for navigating LCD menus.
  1453. //
  1454. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1455. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1456. //
  1457. //#define REVERSE_MENU_DIRECTION
  1458. //
  1459. // This option reverses the encoder direction for Select Screen.
  1460. //
  1461. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1462. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1463. //
  1464. //#define REVERSE_SELECT_DIRECTION
  1465. //
  1466. // Individual Axis Homing
  1467. //
  1468. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1469. //
  1470. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1471. //
  1472. // SPEAKER/BUZZER
  1473. //
  1474. // If you have a speaker that can produce tones, enable it here.
  1475. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1476. //
  1477. //#define SPEAKER
  1478. //
  1479. // The duration and frequency for the UI feedback sound.
  1480. // Set these to 0 to disable audio feedback in the LCD menus.
  1481. //
  1482. // Note: Test audio output with the G-Code:
  1483. // M300 S<frequency Hz> P<duration ms>
  1484. //
  1485. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1486. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1487. //=============================================================================
  1488. //======================== LCD / Controller Selection =========================
  1489. //======================== (Character-based LCDs) =========================
  1490. //=============================================================================
  1491. //
  1492. // RepRapDiscount Smart Controller.
  1493. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1494. //
  1495. // Note: Usually sold with a white PCB.
  1496. //
  1497. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1498. //
  1499. // Original RADDS LCD Display+Encoder+SDCardReader
  1500. // http://doku.radds.org/dokumentation/lcd-display/
  1501. //
  1502. //#define RADDS_DISPLAY
  1503. //
  1504. // ULTIMAKER Controller.
  1505. //
  1506. //#define ULTIMAKERCONTROLLER
  1507. //
  1508. // ULTIPANEL as seen on Thingiverse.
  1509. //
  1510. //#define ULTIPANEL
  1511. //
  1512. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1513. // http://reprap.org/wiki/PanelOne
  1514. //
  1515. //#define PANEL_ONE
  1516. //
  1517. // GADGETS3D G3D LCD/SD Controller
  1518. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1519. //
  1520. // Note: Usually sold with a blue PCB.
  1521. //
  1522. //#define G3D_PANEL
  1523. //
  1524. // RigidBot Panel V1.0
  1525. // http://www.inventapart.com/
  1526. //
  1527. //#define RIGIDBOT_PANEL
  1528. //
  1529. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1530. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1531. //
  1532. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1533. //
  1534. // ANET and Tronxy 20x4 Controller
  1535. //
  1536. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1537. // This LCD is known to be susceptible to electrical interference
  1538. // which scrambles the display. Pressing any button clears it up.
  1539. // This is a LCD2004 display with 5 analog buttons.
  1540. //
  1541. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1542. //
  1543. //#define ULTRA_LCD
  1544. //=============================================================================
  1545. //======================== LCD / Controller Selection =========================
  1546. //===================== (I2C and Shift-Register LCDs) =====================
  1547. //=============================================================================
  1548. //
  1549. // CONTROLLER TYPE: I2C
  1550. //
  1551. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1552. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1553. //
  1554. //
  1555. // Elefu RA Board Control Panel
  1556. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1557. //
  1558. //#define RA_CONTROL_PANEL
  1559. //
  1560. // Sainsmart (YwRobot) LCD Displays
  1561. //
  1562. // These require F.Malpartida's LiquidCrystal_I2C library
  1563. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1564. //
  1565. //#define LCD_SAINSMART_I2C_1602
  1566. //#define LCD_SAINSMART_I2C_2004
  1567. //
  1568. // Generic LCM1602 LCD adapter
  1569. //
  1570. //#define LCM1602
  1571. //
  1572. // PANELOLU2 LCD with status LEDs,
  1573. // separate encoder and click inputs.
  1574. //
  1575. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1576. // For more info: https://github.com/lincomatic/LiquidTWI2
  1577. //
  1578. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1579. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1580. //
  1581. //#define LCD_I2C_PANELOLU2
  1582. //
  1583. // Panucatt VIKI LCD with status LEDs,
  1584. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1585. //
  1586. //#define LCD_I2C_VIKI
  1587. //
  1588. // CONTROLLER TYPE: Shift register panels
  1589. //
  1590. //
  1591. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1592. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1593. //
  1594. //#define SAV_3DLCD
  1595. //
  1596. // 3-wire SR LCD with strobe using 74HC4094
  1597. // https://github.com/mikeshub/SailfishLCD
  1598. // Uses the code directly from Sailfish
  1599. //
  1600. //#define FF_INTERFACEBOARD
  1601. //=============================================================================
  1602. //======================= LCD / Controller Selection =======================
  1603. //========================= (Graphical LCDs) ========================
  1604. //=============================================================================
  1605. //
  1606. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1607. //
  1608. // IMPORTANT: The U8glib library is required for Graphical Display!
  1609. // https://github.com/olikraus/U8glib_Arduino
  1610. //
  1611. //
  1612. // RepRapDiscount FULL GRAPHIC Smart Controller
  1613. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1614. //
  1615. #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1616. //
  1617. // ReprapWorld Graphical LCD
  1618. // https://reprapworld.com/?products_details&products_id/1218
  1619. //
  1620. //#define REPRAPWORLD_GRAPHICAL_LCD
  1621. //
  1622. // Activate one of these if you have a Panucatt Devices
  1623. // Viki 2.0 or mini Viki with Graphic LCD
  1624. // http://panucatt.com
  1625. //
  1626. //#define VIKI2
  1627. //#define miniVIKI
  1628. //
  1629. // MakerLab Mini Panel with graphic
  1630. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1631. //
  1632. //#define MINIPANEL
  1633. //
  1634. // MaKr3d Makr-Panel with graphic controller and SD support.
  1635. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1636. //
  1637. //#define MAKRPANEL
  1638. //
  1639. // Adafruit ST7565 Full Graphic Controller.
  1640. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1641. //
  1642. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1643. //
  1644. // BQ LCD Smart Controller shipped by
  1645. // default with the BQ Hephestos 2 and Witbox 2.
  1646. //
  1647. //#define BQ_LCD_SMART_CONTROLLER
  1648. //
  1649. // Cartesio UI
  1650. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1651. //
  1652. //#define CARTESIO_UI
  1653. //
  1654. // LCD for Melzi Card with Graphical LCD
  1655. //
  1656. //#define LCD_FOR_MELZI
  1657. //
  1658. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1659. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1660. //
  1661. //#define ULTI_CONTROLLER
  1662. //
  1663. // MKS MINI12864 with graphic controller and SD support
  1664. // https://reprap.org/wiki/MKS_MINI_12864
  1665. //
  1666. //#define MKS_MINI_12864
  1667. //
  1668. // FYSETC variant of the MINI12864 graphic controller with SD support
  1669. // https://wiki.fysetc.com/Mini12864_Panel/
  1670. //
  1671. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1672. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1673. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1674. //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight
  1675. //
  1676. // Factory display for Creality CR-10
  1677. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1678. //
  1679. // This is RAMPS-compatible using a single 10-pin connector.
  1680. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1681. //
  1682. //#define CR10_STOCKDISPLAY
  1683. //
  1684. // ANET and Tronxy Graphical Controller
  1685. //
  1686. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1687. // A clone of the RepRapDiscount full graphics display but with
  1688. // different pins/wiring (see pins_ANET_10.h).
  1689. //
  1690. //#define ANET_FULL_GRAPHICS_LCD
  1691. //
  1692. // AZSMZ 12864 LCD with SD
  1693. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1694. //
  1695. //#define AZSMZ_12864
  1696. //
  1697. // Silvergate GLCD controller
  1698. // http://github.com/android444/Silvergate
  1699. //
  1700. //#define SILVER_GATE_GLCD_CONTROLLER
  1701. //=============================================================================
  1702. //============================== OLED Displays ==============================
  1703. //=============================================================================
  1704. //
  1705. // SSD1306 OLED full graphics generic display
  1706. //
  1707. //#define U8GLIB_SSD1306
  1708. //
  1709. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1710. //
  1711. //#define SAV_3DGLCD
  1712. #if ENABLED(SAV_3DGLCD)
  1713. #define U8GLIB_SSD1306
  1714. //#define U8GLIB_SH1106
  1715. #endif
  1716. //
  1717. // TinyBoy2 128x64 OLED / Encoder Panel
  1718. //
  1719. //#define OLED_PANEL_TINYBOY2
  1720. //
  1721. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1722. // http://reprap.org/wiki/MKS_12864OLED
  1723. //
  1724. // Tiny, but very sharp OLED display
  1725. //
  1726. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1727. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1728. //
  1729. // Einstart S OLED SSD1306
  1730. //
  1731. //#define U8GLIB_SH1106_EINSTART
  1732. //
  1733. // Overlord OLED display/controller with i2c buzzer and LEDs
  1734. //
  1735. //#define OVERLORD_OLED
  1736. //=============================================================================
  1737. //========================== Extensible UI Displays ===========================
  1738. //=============================================================================
  1739. //
  1740. // DGUS Touch Display with DWIN OS
  1741. //
  1742. //#define DGUS_LCD
  1743. //
  1744. // Touch-screen LCD for Malyan M200 printers
  1745. //
  1746. //#define MALYAN_LCD
  1747. //
  1748. // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
  1749. // See Configuration_adv.h for all configuration options.
  1750. //
  1751. //#define LULZBOT_TOUCH_UI
  1752. //
  1753. // Third-party or vendor-customized controller interfaces.
  1754. // Sources should be installed in 'src/lcd/extensible_ui'.
  1755. //
  1756. //#define EXTENSIBLE_UI
  1757. //=============================================================================
  1758. //=============================== Graphical TFTs ==============================
  1759. //=============================================================================
  1760. //
  1761. // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
  1762. //
  1763. //#define FSMC_GRAPHICAL_TFT
  1764. //=============================================================================
  1765. //============================ Other Controllers ============================
  1766. //=============================================================================
  1767. //
  1768. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  1769. //
  1770. //#define TOUCH_BUTTONS
  1771. #if ENABLED(TOUCH_BUTTONS)
  1772. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  1773. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  1774. #define XPT2046_X_CALIBRATION 12316
  1775. #define XPT2046_Y_CALIBRATION -8981
  1776. #define XPT2046_X_OFFSET -43
  1777. #define XPT2046_Y_OFFSET 257
  1778. #endif
  1779. //
  1780. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1781. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1782. //
  1783. //#define REPRAPWORLD_KEYPAD
  1784. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  1785. //=============================================================================
  1786. //=============================== Extra Features ==============================
  1787. //=============================================================================
  1788. // @section extras
  1789. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1790. //#define FAST_PWM_FAN
  1791. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1792. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1793. // is too low, you should also increment SOFT_PWM_SCALE.
  1794. //#define FAN_SOFT_PWM
  1795. // Incrementing this by 1 will double the software PWM frequency,
  1796. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1797. // However, control resolution will be halved for each increment;
  1798. // at zero value, there are 128 effective control positions.
  1799. // :[0,1,2,3,4,5,6,7]
  1800. #define SOFT_PWM_SCALE 0
  1801. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1802. // be used to mitigate the associated resolution loss. If enabled,
  1803. // some of the PWM cycles are stretched so on average the desired
  1804. // duty cycle is attained.
  1805. //#define SOFT_PWM_DITHER
  1806. // Temperature status LEDs that display the hotend and bed temperature.
  1807. // If all hotends, bed temperature, and target temperature are under 54C
  1808. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1809. //#define TEMP_STAT_LEDS
  1810. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1811. //#define SF_ARC_FIX
  1812. // Support for the BariCUDA Paste Extruder
  1813. //#define BARICUDA
  1814. // Support for BlinkM/CyzRgb
  1815. //#define BLINKM
  1816. // Support for PCA9632 PWM LED driver
  1817. //#define PCA9632
  1818. // Support for PCA9533 PWM LED driver
  1819. // https://github.com/mikeshub/SailfishRGB_LED
  1820. //#define PCA9533
  1821. /**
  1822. * RGB LED / LED Strip Control
  1823. *
  1824. * Enable support for an RGB LED connected to 5V digital pins, or
  1825. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1826. *
  1827. * Adds the M150 command to set the LED (or LED strip) color.
  1828. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1829. * luminance values can be set from 0 to 255.
  1830. * For Neopixel LED an overall brightness parameter is also available.
  1831. *
  1832. * *** CAUTION ***
  1833. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1834. * as the Arduino cannot handle the current the LEDs will require.
  1835. * Failure to follow this precaution can destroy your Arduino!
  1836. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1837. * more current than the Arduino 5V linear regulator can produce.
  1838. * *** CAUTION ***
  1839. *
  1840. * LED Type. Enable only one of the following two options.
  1841. *
  1842. */
  1843. //#define RGB_LED
  1844. //#define RGBW_LED
  1845. #if EITHER(RGB_LED, RGBW_LED)
  1846. //#define RGB_LED_R_PIN 34
  1847. //#define RGB_LED_G_PIN 43
  1848. //#define RGB_LED_B_PIN 35
  1849. //#define RGB_LED_W_PIN -1
  1850. #endif
  1851. // Support for Adafruit Neopixel LED driver
  1852. //#define NEOPIXEL_LED
  1853. #if ENABLED(NEOPIXEL_LED)
  1854. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1855. #define NEOPIXEL_PIN 4 // LED driving pin
  1856. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  1857. //#define NEOPIXEL2_PIN 5
  1858. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
  1859. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1860. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1861. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1862. // Use a single Neopixel LED for static (background) lighting
  1863. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  1864. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  1865. #endif
  1866. /**
  1867. * Printer Event LEDs
  1868. *
  1869. * During printing, the LEDs will reflect the printer status:
  1870. *
  1871. * - Gradually change from blue to violet as the heated bed gets to target temp
  1872. * - Gradually change from violet to red as the hotend gets to temperature
  1873. * - Change to white to illuminate work surface
  1874. * - Change to green once print has finished
  1875. * - Turn off after the print has finished and the user has pushed a button
  1876. */
  1877. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  1878. #define PRINTER_EVENT_LEDS
  1879. #endif
  1880. /**
  1881. * R/C SERVO support
  1882. * Sponsored by TrinityLabs, Reworked by codexmas
  1883. */
  1884. /**
  1885. * Number of servos
  1886. *
  1887. * For some servo-related options NUM_SERVOS will be set automatically.
  1888. * Set this manually if there are extra servos needing manual control.
  1889. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1890. */
  1891. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1892. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  1893. // 300ms is a good value but you can try less delay.
  1894. // If the servo can't reach the requested position, increase it.
  1895. #define SERVO_DELAY { 300 }
  1896. // Only power servos during movement, otherwise leave off to prevent jitter
  1897. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1898. // Allow servo angle to be edited and saved to EEPROM
  1899. //#define EDITABLE_SERVO_ANGLES