My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Вы не можете выбрать более 25 тем Темы должны начинаться с буквы или цифры, могут содержать дефисы(-) и должны содержать не более 35 символов.

Configuration.h 79KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098109911001101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125112611271128112911301131113211331134113511361137113811391140114111421143114411451146114711481149115011511152115311541155115611571158115911601161116211631164116511661167116811691170117111721173117411751176117711781179118011811182118311841185118611871188118911901191119211931194119511961197119811991200120112021203120412051206120712081209121012111212121312141215121612171218121912201221122212231224122512261227122812291230123112321233123412351236123712381239124012411242124312441245124612471248124912501251125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275127612771278127912801281128212831284128512861287128812891290129112921293129412951296129712981299130013011302130313041305130613071308130913101311131213131314131513161317131813191320132113221323132413251326132713281329133013311332133313341335133613371338133913401341134213431344134513461347134813491350135113521353135413551356135713581359136013611362136313641365136613671368136913701371137213731374137513761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410141114121413141414151416141714181419142014211422142314241425142614271428142914301431143214331434143514361437143814391440144114421443144414451446144714481449145014511452145314541455145614571458145914601461146214631464146514661467146814691470147114721473147414751476147714781479148014811482148314841485148614871488148914901491149214931494149514961497149814991500150115021503150415051506150715081509151015111512151315141515151615171518151915201521152215231524152515261527152815291530153115321533153415351536153715381539154015411542154315441545154615471548154915501551155215531554155515561557155815591560156115621563156415651566156715681569157015711572157315741575157615771578157915801581158215831584158515861587158815891590159115921593159415951596159715981599160016011602160316041605160616071608160916101611161216131614161516161617161816191620162116221623162416251626162716281629163016311632163316341635163616371638163916401641164216431644164516461647164816491650165116521653165416551656165716581659166016611662166316641665166616671668166916701671167216731674167516761677167816791680168116821683168416851686168716881689169016911692169316941695169616971698169917001701170217031704170517061707170817091710171117121713171417151716171717181719172017211722172317241725172617271728172917301731173217331734173517361737173817391740174117421743174417451746174717481749175017511752175317541755175617571758175917601761176217631764176517661767176817691770177117721773177417751776177717781779178017811782178317841785178617871788178917901791179217931794179517961797179817991800180118021803180418051806180718081809181018111812181318141815181618171818181918201821182218231824182518261827182818291830183118321833183418351836183718381839184018411842184318441845184618471848184918501851185218531854185518561857185818591860186118621863186418651866186718681869187018711872187318741875187618771878187918801881188218831884188518861887188818891890189118921893189418951896189718981899190019011902190319041905190619071908190919101911191219131914191519161917191819191920192119221923192419251926192719281929193019311932193319341935193619371938193919401941194219431944194519461947194819491950195119521953195419551956195719581959196019611962196319641965196619671968196919701971197219731974197519761977197819791980198119821983198419851986198719881989199019911992199319941995199619971998199920002001200220032004200520062007200820092010201120122013201420152016201720182019202020212022202320242025202620272028202920302031203220332034203520362037203820392040204120422043204420452046204720482049205020512052205320542055205620572058205920602061206220632064206520662067206820692070207120722073207420752076207720782079208020812082208320842085208620872088208920902091209220932094209520962097209820992100210121022103210421052106210721082109211021112112211321142115211621172118211921202121212221232124212521262127212821292130213121322133213421352136213721382139214021412142214321442145214621472148214921502151215221532154215521562157215821592160216121622163216421652166216721682169217021712172217321742175217621772178217921802181218221832184218521862187218821892190219121922193219421952196219721982199220022012202220322042205220622072208220922102211221222132214221522162217221822192220222122222223222422252226222722282229
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #define CONFIGURATION_H_VERSION 020000
  39. //===========================================================================
  40. //============================= Getting Started =============================
  41. //===========================================================================
  42. /**
  43. * Here are some standard links for getting your machine calibrated:
  44. *
  45. * http://reprap.org/wiki/Calibration
  46. * http://youtu.be/wAL9d7FgInk
  47. * http://calculator.josefprusa.cz
  48. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  49. * http://www.thingiverse.com/thing:5573
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * http://www.thingiverse.com/thing:298812
  52. */
  53. //===========================================================================
  54. //============================= DELTA Printer ===============================
  55. //===========================================================================
  56. // For a Delta printer start with one of the configuration files in the
  57. // config/examples/delta directory and customize for your machine.
  58. //
  59. //===========================================================================
  60. //============================= SCARA Printer ===============================
  61. //===========================================================================
  62. // For a SCARA printer start with the configuration files in
  63. // config/examples/SCARA and customize for your machine.
  64. //
  65. // @section info
  66. // Author info of this build printed to the host during boot and M115
  67. #define STRING_CONFIG_H_AUTHOR "(tjclement, Infitary M508)" // Who made the changes.
  68. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  69. /**
  70. * *** VENDORS PLEASE READ ***
  71. *
  72. * Marlin allows you to add a custom boot image for Graphical LCDs.
  73. * With this option Marlin will first show your custom screen followed
  74. * by the standard Marlin logo with version number and web URL.
  75. *
  76. * We encourage you to take advantage of this new feature and we also
  77. * respectfully request that you retain the unmodified Marlin boot screen.
  78. */
  79. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  80. #define SHOW_BOOTSCREEN
  81. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  82. //#define SHOW_CUSTOM_BOOTSCREEN
  83. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  84. //#define CUSTOM_STATUS_SCREEN_IMAGE
  85. // @section machine
  86. /**
  87. * Select the serial port on the board to use for communication with the host.
  88. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  89. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  90. *
  91. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  92. */
  93. #define SERIAL_PORT 0
  94. /**
  95. * Select a secondary serial port on the board to use for communication with the host.
  96. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  97. * Serial port -1 is the USB emulated serial port, if available.
  98. *
  99. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  100. */
  101. //#define SERIAL_PORT_2 -1
  102. /**
  103. * This setting determines the communication speed of the printer.
  104. *
  105. * 250000 works in most cases, but you might try a lower speed if
  106. * you commonly experience drop-outs during host printing.
  107. * You may try up to 1000000 to speed up SD file transfer.
  108. *
  109. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  110. */
  111. #define BAUDRATE 250000
  112. // Enable the Bluetooth serial interface on AT90USB devices
  113. //#define BLUETOOTH
  114. // Choose the name from boards.h that matches your setup
  115. #ifndef MOTHERBOARD
  116. #define MOTHERBOARD BOARD_RAMPS_13_EFB
  117. #endif
  118. // Name displayed in the LCD "Ready" message and Info menu
  119. #define CUSTOM_MACHINE_NAME "Infitary M508"
  120. // Printer's unique ID, used by some programs to differentiate between machines.
  121. // Choose your own or use a service like http://www.uuidgenerator.net/version4
  122. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  123. // @section extruder
  124. // This defines the number of extruders
  125. // :[1, 2, 3, 4, 5, 6]
  126. #define EXTRUDERS 1
  127. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  128. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
  129. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  130. //#define SINGLENOZZLE
  131. /**
  132. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  133. *
  134. * This device allows one stepper driver on a control board to drive
  135. * two to eight stepper motors, one at a time, in a manner suitable
  136. * for extruders.
  137. *
  138. * This option only allows the multiplexer to switch on tool-change.
  139. * Additional options to configure custom E moves are pending.
  140. */
  141. //#define MK2_MULTIPLEXER
  142. #if ENABLED(MK2_MULTIPLEXER)
  143. // Override the default DIO selector pins here, if needed.
  144. // Some pins files may provide defaults for these pins.
  145. //#define E_MUX0_PIN 40 // Always Required
  146. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  147. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  148. #endif
  149. /**
  150. * Prusa Multi-Material Unit v2
  151. *
  152. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  153. * Requires EXTRUDERS = 5
  154. *
  155. * For additional configuration see Configuration_adv.h
  156. */
  157. //#define PRUSA_MMU2
  158. // A dual extruder that uses a single stepper motor
  159. //#define SWITCHING_EXTRUDER
  160. #if ENABLED(SWITCHING_EXTRUDER)
  161. #define SWITCHING_EXTRUDER_SERVO_NR 0
  162. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  163. #if EXTRUDERS > 3
  164. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  165. #endif
  166. #endif
  167. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  168. //#define SWITCHING_NOZZLE
  169. #if ENABLED(SWITCHING_NOZZLE)
  170. #define SWITCHING_NOZZLE_SERVO_NR 0
  171. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  172. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  173. #endif
  174. /**
  175. * Two separate X-carriages with extruders that connect to a moving part
  176. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  177. */
  178. //#define PARKING_EXTRUDER
  179. /**
  180. * Two separate X-carriages with extruders that connect to a moving part
  181. * via a magnetic docking mechanism using movements and no solenoid
  182. *
  183. * project : https://www.thingiverse.com/thing:3080893
  184. * movements : https://youtu.be/0xCEiG9VS3k
  185. * https://youtu.be/Bqbcs0CU2FE
  186. */
  187. //#define MAGNETIC_PARKING_EXTRUDER
  188. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  189. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  190. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  191. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  192. #if ENABLED(PARKING_EXTRUDER)
  193. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  194. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  195. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  196. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  197. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  198. #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
  199. #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
  200. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  201. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  202. #endif
  203. #endif
  204. /**
  205. * Switching Toolhead
  206. *
  207. * Support for swappable and dockable toolheads, such as
  208. * the E3D Tool Changer. Toolheads are locked with a servo.
  209. */
  210. //#define SWITCHING_TOOLHEAD
  211. /**
  212. * Magnetic Switching Toolhead
  213. *
  214. * Support swappable and dockable toolheads with a magnetic
  215. * docking mechanism using movement and no servo.
  216. */
  217. //#define MAGNETIC_SWITCHING_TOOLHEAD
  218. /**
  219. * Electromagnetic Switching Toolhead
  220. *
  221. * Parking for CoreXY / HBot kinematics.
  222. * Toolheads are parked at one edge and held with an electromagnet.
  223. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  224. */
  225. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  226. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  227. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  228. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  229. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  230. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  231. #if ENABLED(SWITCHING_TOOLHEAD)
  232. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  233. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  234. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  235. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  236. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  237. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  238. #if ENABLED(PRIME_BEFORE_REMOVE)
  239. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  240. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  241. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate
  242. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate
  243. #endif
  244. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  245. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  246. #endif
  247. #endif
  248. /**
  249. * "Mixing Extruder"
  250. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  251. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  252. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  253. * - This implementation supports up to two mixing extruders.
  254. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  255. */
  256. //#define MIXING_EXTRUDER
  257. #if ENABLED(MIXING_EXTRUDER)
  258. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  259. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  260. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  261. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  262. #if ENABLED(GRADIENT_MIX)
  263. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  264. #endif
  265. #endif
  266. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  267. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  268. // For the other hotends it is their distance from the extruder 0 hotend.
  269. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  270. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  271. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  272. // @section machine
  273. /**
  274. * Power Supply Control
  275. *
  276. * Enable and connect the power supply to the PS_ON_PIN.
  277. * Specify whether the power supply is active HIGH or active LOW.
  278. */
  279. //#define PSU_CONTROL
  280. //#define PSU_NAME "Power Supply"
  281. #if ENABLED(PSU_CONTROL)
  282. #define PSU_ACTIVE_HIGH false // Set 'false' for ATX, 'true' for X-Box
  283. //#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80
  284. //#define PSU_POWERUP_DELAY 100 // (ms) Delay for the PSU to warm up to full power
  285. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  286. #if ENABLED(AUTO_POWER_CONTROL)
  287. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  288. #define AUTO_POWER_E_FANS
  289. #define AUTO_POWER_CONTROLLERFAN
  290. #define AUTO_POWER_CHAMBER_FAN
  291. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature
  292. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature
  293. #define POWER_TIMEOUT 30
  294. #endif
  295. #endif
  296. // @section temperature
  297. //===========================================================================
  298. //============================= Thermal Settings ============================
  299. //===========================================================================
  300. /**
  301. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  302. *
  303. * Temperature sensors available:
  304. *
  305. * -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
  306. * -3 : thermocouple with MAX31855 (only for sensors 0-1)
  307. * -2 : thermocouple with MAX6675 (only for sensors 0-1)
  308. * -4 : thermocouple with AD8495
  309. * -1 : thermocouple with AD595
  310. * 0 : not used
  311. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  312. * 331 : (3.3V scaled thermistor 1 table)
  313. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  314. * 3 : Mendel-parts thermistor (4.7k pullup)
  315. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  316. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  317. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  318. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  319. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  320. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  321. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  322. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  323. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  324. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  325. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  326. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  327. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  328. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  329. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  330. * 20 : Pt100 with circuit in the Ultimainboard V2.x
  331. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  332. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  333. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  334. * 66 : 4.7M High Temperature thermistor from Dyze Design
  335. * 67 : 450C thermistor from SliceEngineering
  336. * 70 : the 100K thermistor found in the bq Hephestos 2
  337. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  338. * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
  339. *
  340. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  341. * (but gives greater accuracy and more stable PID)
  342. * 51 : 100k thermistor - EPCOS (1k pullup)
  343. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  344. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  345. *
  346. * 1047 : Pt1000 with 4k7 pullup
  347. * 1010 : Pt1000 with 1k pullup (non standard)
  348. * 147 : Pt100 with 4k7 pullup
  349. * 110 : Pt100 with 1k pullup (non standard)
  350. *
  351. * 1000 : Custom - Specify parameters in Configuration_adv.h
  352. *
  353. * Use these for Testing or Development purposes. NEVER for production machine.
  354. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  355. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  356. */
  357. #define TEMP_SENSOR_0 1
  358. #define TEMP_SENSOR_1 0
  359. #define TEMP_SENSOR_2 0
  360. #define TEMP_SENSOR_3 0
  361. #define TEMP_SENSOR_4 0
  362. #define TEMP_SENSOR_5 0
  363. #define TEMP_SENSOR_BED 1
  364. #define TEMP_SENSOR_CHAMBER 0
  365. // Dummy thermistor constant temperature readings, for use with 998 and 999
  366. #define DUMMY_THERMISTOR_998_VALUE 25
  367. #define DUMMY_THERMISTOR_999_VALUE 100
  368. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  369. // from the two sensors differ too much the print will be aborted.
  370. //#define TEMP_SENSOR_1_AS_REDUNDANT
  371. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  372. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  373. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  374. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  375. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  376. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  377. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  378. // Below this temperature the heater will be switched off
  379. // because it probably indicates a broken thermistor wire.
  380. #define HEATER_0_MINTEMP 5
  381. #define HEATER_1_MINTEMP 5
  382. #define HEATER_2_MINTEMP 5
  383. #define HEATER_3_MINTEMP 5
  384. #define HEATER_4_MINTEMP 5
  385. #define HEATER_5_MINTEMP 5
  386. #define BED_MINTEMP 5
  387. // Above this temperature the heater will be switched off.
  388. // This can protect components from overheating, but NOT from shorts and failures.
  389. // (Use MINTEMP for thermistor short/failure protection.)
  390. #define HEATER_0_MAXTEMP 275
  391. #define HEATER_1_MAXTEMP 275
  392. #define HEATER_2_MAXTEMP 275
  393. #define HEATER_3_MAXTEMP 275
  394. #define HEATER_4_MAXTEMP 275
  395. #define HEATER_5_MAXTEMP 275
  396. #define BED_MAXTEMP 125
  397. //===========================================================================
  398. //============================= PID Settings ================================
  399. //===========================================================================
  400. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  401. // Comment the following line to disable PID and enable bang-bang.
  402. #define PIDTEMP
  403. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  404. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  405. #define PID_K1 0.95 // Smoothing factor within any PID loop
  406. #if ENABLED(PIDTEMP)
  407. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  408. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  409. //#define PID_DEBUG // Sends debug data to the serial port.
  410. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  411. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  412. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  413. // Set/get with gcode: M301 E[extruder number, 0-2]
  414. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  415. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  416. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  417. // Ultimaker
  418. //#define DEFAULT_Kp 22.2
  419. //#define DEFAULT_Ki 1.08
  420. //#define DEFAULT_Kd 114
  421. // MakerGear
  422. //#define DEFAULT_Kp 7.0
  423. //#define DEFAULT_Ki 0.1
  424. //#define DEFAULT_Kd 12
  425. // Mendel Parts V9 on 12V
  426. //#define DEFAULT_Kp 63.0
  427. //#define DEFAULT_Ki 2.25
  428. //#define DEFAULT_Kd 440
  429. #define DEFAULT_Kp 213.2
  430. #define DEFAULT_Ki 1.54
  431. #define DEFAULT_Kd 765
  432. #endif // PIDTEMP
  433. //===========================================================================
  434. //====================== PID > Bed Temperature Control ======================
  435. //===========================================================================
  436. /**
  437. * PID Bed Heating
  438. *
  439. * If this option is enabled set PID constants below.
  440. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  441. *
  442. * The PID frequency will be the same as the extruder PWM.
  443. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  444. * which is fine for driving a square wave into a resistive load and does not significantly
  445. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  446. * heater. If your configuration is significantly different than this and you don't understand
  447. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  448. */
  449. //#define PIDTEMPBED
  450. //#define BED_LIMIT_SWITCHING
  451. /**
  452. * Max Bed Power
  453. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  454. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  455. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  456. */
  457. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  458. #if ENABLED(PIDTEMPBED)
  459. //#define MIN_BED_POWER 0
  460. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  461. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  462. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  463. #define DEFAULT_bedKp 10.00
  464. #define DEFAULT_bedKi .023
  465. #define DEFAULT_bedKd 305.4
  466. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  467. //from pidautotune
  468. //#define DEFAULT_bedKp 97.1
  469. //#define DEFAULT_bedKi 1.41
  470. //#define DEFAULT_bedKd 1675.16
  471. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  472. #endif // PIDTEMPBED
  473. // @section extruder
  474. /**
  475. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  476. * Add M302 to set the minimum extrusion temperature and/or turn
  477. * cold extrusion prevention on and off.
  478. *
  479. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  480. */
  481. #define PREVENT_COLD_EXTRUSION
  482. #define EXTRUDE_MINTEMP 170
  483. /**
  484. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  485. * Note: For Bowden Extruders make this large enough to allow load/unload.
  486. */
  487. #define PREVENT_LENGTHY_EXTRUDE
  488. #define EXTRUDE_MAXLENGTH 200
  489. //===========================================================================
  490. //======================== Thermal Runaway Protection =======================
  491. //===========================================================================
  492. /**
  493. * Thermal Protection provides additional protection to your printer from damage
  494. * and fire. Marlin always includes safe min and max temperature ranges which
  495. * protect against a broken or disconnected thermistor wire.
  496. *
  497. * The issue: If a thermistor falls out, it will report the much lower
  498. * temperature of the air in the room, and the the firmware will keep
  499. * the heater on.
  500. *
  501. * If you get "Thermal Runaway" or "Heating failed" errors the
  502. * details can be tuned in Configuration_adv.h
  503. */
  504. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  505. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  506. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  507. //===========================================================================
  508. //============================= Mechanical Settings =========================
  509. //===========================================================================
  510. // @section machine
  511. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  512. // either in the usual order or reversed
  513. //#define COREXY
  514. //#define COREXZ
  515. //#define COREYZ
  516. //#define COREYX
  517. //#define COREZX
  518. //#define COREZY
  519. //===========================================================================
  520. //============================== Endstop Settings ===========================
  521. //===========================================================================
  522. // @section homing
  523. // Specify here all the endstop connectors that are connected to any endstop or probe.
  524. // Almost all printers will be using one per axis. Probes will use one or more of the
  525. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  526. #define USE_XMIN_PLUG
  527. #define USE_YMIN_PLUG
  528. #define USE_ZMIN_PLUG
  529. //#define USE_XMAX_PLUG
  530. //#define USE_YMAX_PLUG
  531. //#define USE_ZMAX_PLUG
  532. // Enable pullup for all endstops to prevent a floating state
  533. #define ENDSTOPPULLUPS
  534. #if DISABLED(ENDSTOPPULLUPS)
  535. // Disable ENDSTOPPULLUPS to set pullups individually
  536. //#define ENDSTOPPULLUP_XMAX
  537. //#define ENDSTOPPULLUP_YMAX
  538. //#define ENDSTOPPULLUP_ZMAX
  539. //#define ENDSTOPPULLUP_XMIN
  540. //#define ENDSTOPPULLUP_YMIN
  541. //#define ENDSTOPPULLUP_ZMIN
  542. //#define ENDSTOPPULLUP_ZMIN_PROBE
  543. #endif
  544. // Enable pulldown for all endstops to prevent a floating state
  545. //#define ENDSTOPPULLDOWNS
  546. #if DISABLED(ENDSTOPPULLDOWNS)
  547. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  548. //#define ENDSTOPPULLDOWN_XMAX
  549. //#define ENDSTOPPULLDOWN_YMAX
  550. //#define ENDSTOPPULLDOWN_ZMAX
  551. //#define ENDSTOPPULLDOWN_XMIN
  552. //#define ENDSTOPPULLDOWN_YMIN
  553. //#define ENDSTOPPULLDOWN_ZMIN
  554. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  555. #endif
  556. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  557. #define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  558. #define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  559. #define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  560. #define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  561. #define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  562. #define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  563. #define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
  564. /**
  565. * Stepper Drivers
  566. *
  567. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  568. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  569. *
  570. * A4988 is assumed for unspecified drivers.
  571. *
  572. * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  573. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  574. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  575. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  576. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  577. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  578. */
  579. //#define X_DRIVER_TYPE A4988
  580. //#define Y_DRIVER_TYPE A4988
  581. //#define Z_DRIVER_TYPE A4988
  582. //#define X2_DRIVER_TYPE A4988
  583. //#define Y2_DRIVER_TYPE A4988
  584. //#define Z2_DRIVER_TYPE A4988
  585. //#define Z3_DRIVER_TYPE A4988
  586. //#define E0_DRIVER_TYPE A4988
  587. //#define E1_DRIVER_TYPE A4988
  588. //#define E2_DRIVER_TYPE A4988
  589. //#define E3_DRIVER_TYPE A4988
  590. //#define E4_DRIVER_TYPE A4988
  591. //#define E5_DRIVER_TYPE A4988
  592. // Enable this feature if all enabled endstop pins are interrupt-capable.
  593. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  594. //#define ENDSTOP_INTERRUPTS_FEATURE
  595. /**
  596. * Endstop Noise Threshold
  597. *
  598. * Enable if your probe or endstops falsely trigger due to noise.
  599. *
  600. * - Higher values may affect repeatability or accuracy of some bed probes.
  601. * - To fix noise install a 100nF ceramic capacitor inline with the switch.
  602. * - This feature is not required for common micro-switches mounted on PCBs
  603. * based on the Makerbot design, which already have the 100nF capacitor.
  604. *
  605. * :[2,3,4,5,6,7]
  606. */
  607. //#define ENDSTOP_NOISE_THRESHOLD 2
  608. //=============================================================================
  609. //============================== Movement Settings ============================
  610. //=============================================================================
  611. // @section motion
  612. /**
  613. * Default Settings
  614. *
  615. * These settings can be reset by M502
  616. *
  617. * Note that if EEPROM is enabled, saved values will override these.
  618. */
  619. /**
  620. * With this option each E stepper can have its own factors for the
  621. * following movement settings. If fewer factors are given than the
  622. * total number of extruders, the last value applies to the rest.
  623. */
  624. //#define DISTINCT_E_FACTORS
  625. /**
  626. * Default Axis Steps Per Unit (steps/mm)
  627. * Override with M92
  628. * X, Y, Z, E0 [, E1[, E2...]]
  629. */
  630. #define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 92.6 }
  631. /**
  632. * Default Max Feed Rate (mm/s)
  633. * Override with M203
  634. * X, Y, Z, E0 [, E1[, E2...]]
  635. */
  636. #define DEFAULT_MAX_FEEDRATE { 400, 400, 5, 25 }
  637. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  638. #if ENABLED(LIMITED_MAX_FR_EDITING)
  639. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  640. #endif
  641. /**
  642. * Default Max Acceleration (change/s) change = mm/s
  643. * (Maximum start speed for accelerated moves)
  644. * Override with M201
  645. * X, Y, Z, E0 [, E1[, E2...]]
  646. */
  647. #define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
  648. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  649. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  650. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  651. #endif
  652. /**
  653. * Default Acceleration (change/s) change = mm/s
  654. * Override with M204
  655. *
  656. * M204 P Acceleration
  657. * M204 R Retract Acceleration
  658. * M204 T Travel Acceleration
  659. */
  660. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
  661. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  662. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  663. /**
  664. * Default Jerk limits (mm/s)
  665. * Override with M205 X Y Z E
  666. *
  667. * "Jerk" specifies the minimum speed change that requires acceleration.
  668. * When changing speed and direction, if the difference is less than the
  669. * value set here, it may happen instantaneously.
  670. */
  671. //#define CLASSIC_JERK
  672. #if ENABLED(CLASSIC_JERK)
  673. #define DEFAULT_XJERK 10.0
  674. #define DEFAULT_YJERK 10.0
  675. #define DEFAULT_ZJERK 0.3
  676. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  677. #if ENABLED(LIMITED_JERK_EDITING)
  678. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  679. #endif
  680. #endif
  681. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  682. /**
  683. * Junction Deviation Factor
  684. *
  685. * See:
  686. * https://reprap.org/forum/read.php?1,739819
  687. * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  688. */
  689. #if DISABLED(CLASSIC_JERK)
  690. #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
  691. #endif
  692. /**
  693. * S-Curve Acceleration
  694. *
  695. * This option eliminates vibration during printing by fitting a Bézier
  696. * curve to move acceleration, producing much smoother direction changes.
  697. *
  698. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  699. */
  700. //#define S_CURVE_ACCELERATION
  701. //===========================================================================
  702. //============================= Z Probe Options =============================
  703. //===========================================================================
  704. // @section probes
  705. //
  706. // See http://marlinfw.org/docs/configuration/probes.html
  707. //
  708. /**
  709. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  710. *
  711. * Enable this option for a probe connected to the Z Min endstop pin.
  712. */
  713. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  714. /**
  715. * Z_MIN_PROBE_PIN
  716. *
  717. * Define this pin if the probe is not connected to Z_MIN_PIN.
  718. * If not defined the default pin for the selected MOTHERBOARD
  719. * will be used. Most of the time the default is what you want.
  720. *
  721. * - The simplest option is to use a free endstop connector.
  722. * - Use 5V for powered (usually inductive) sensors.
  723. *
  724. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  725. * - For simple switches connect...
  726. * - normally-closed switches to GND and D32.
  727. * - normally-open switches to 5V and D32.
  728. *
  729. */
  730. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  731. /**
  732. * Probe Type
  733. *
  734. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  735. * Activate one of these to use Auto Bed Leveling below.
  736. */
  737. /**
  738. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  739. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  740. * or (with LCD_BED_LEVELING) the LCD controller.
  741. */
  742. //#define PROBE_MANUALLY
  743. //#define MANUAL_PROBE_START_Z 0.2
  744. /**
  745. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  746. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  747. */
  748. //#define FIX_MOUNTED_PROBE
  749. /**
  750. * Use the nozzle as the probe, as with a conductive
  751. * nozzle system or a piezo-electric smart effector.
  752. */
  753. //#define NOZZLE_AS_PROBE
  754. /**
  755. * Z Servo Probe, such as an endstop switch on a rotating arm.
  756. */
  757. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  758. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  759. /**
  760. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  761. */
  762. //#define BLTOUCH
  763. /**
  764. * Touch-MI Probe by hotends.fr
  765. *
  766. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  767. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  768. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  769. *
  770. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  771. * and a minimum Z_HOMING_HEIGHT of 10.
  772. */
  773. //#define TOUCH_MI_PROBE
  774. #if ENABLED(TOUCH_MI_PROBE)
  775. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  776. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  777. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  778. #endif
  779. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  780. //#define SOLENOID_PROBE
  781. // A sled-mounted probe like those designed by Charles Bell.
  782. //#define Z_PROBE_SLED
  783. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  784. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  785. //#define RACK_AND_PINION_PROBE
  786. #if ENABLED(RACK_AND_PINION_PROBE)
  787. #define Z_PROBE_DEPLOY_X X_MIN_POS
  788. #define Z_PROBE_RETRACT_X X_MAX_POS
  789. #endif
  790. //
  791. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  792. //
  793. /**
  794. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  795. *
  796. * In the following example the X and Y offsets are both positive:
  797. *
  798. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  799. *
  800. * +-- BACK ---+
  801. * | |
  802. * L | (+) P | R <-- probe (20,20)
  803. * E | | I
  804. * F | (-) N (+) | G <-- nozzle (10,10)
  805. * T | | H
  806. * | (-) | T
  807. * | |
  808. * O-- FRONT --+
  809. * (0,0)
  810. *
  811. * Specify a Probe position as { X, Y, Z }
  812. */
  813. #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  814. // Most probes should stay away from the edges of the bed, but
  815. // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
  816. #define MIN_PROBE_EDGE 10
  817. // X and Y axis travel speed (mm/m) between probes
  818. #define XY_PROBE_SPEED 8000
  819. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  820. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  821. // Feedrate (mm/m) for the "accurate" probe of each point
  822. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  823. /**
  824. * Multiple Probing
  825. *
  826. * You may get improved results by probing 2 or more times.
  827. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  828. *
  829. * A total of 2 does fast/slow probes with a weighted average.
  830. * A total of 3 or more adds more slow probes, taking the average.
  831. */
  832. //#define MULTIPLE_PROBING 2
  833. //#define EXTRA_PROBING 1
  834. /**
  835. * Z probes require clearance when deploying, stowing, and moving between
  836. * probe points to avoid hitting the bed and other hardware.
  837. * Servo-mounted probes require extra space for the arm to rotate.
  838. * Inductive probes need space to keep from triggering early.
  839. *
  840. * Use these settings to specify the distance (mm) to raise the probe (or
  841. * lower the bed). The values set here apply over and above any (negative)
  842. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  843. * Only integer values >= 1 are valid here.
  844. *
  845. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  846. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  847. */
  848. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  849. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  850. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  851. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  852. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  853. // For M851 give a range for adjusting the Z probe offset
  854. #define Z_PROBE_OFFSET_RANGE_MIN -20
  855. #define Z_PROBE_OFFSET_RANGE_MAX 20
  856. // Enable the M48 repeatability test to test probe accuracy
  857. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  858. // Before deploy/stow pause for user confirmation
  859. //#define PAUSE_BEFORE_DEPLOY_STOW
  860. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  861. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  862. #endif
  863. /**
  864. * Enable one or more of the following if probing seems unreliable.
  865. * Heaters and/or fans can be disabled during probing to minimize electrical
  866. * noise. A delay can also be added to allow noise and vibration to settle.
  867. * These options are most useful for the BLTouch probe, but may also improve
  868. * readings with inductive probes and piezo sensors.
  869. */
  870. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  871. #if ENABLED(PROBING_HEATERS_OFF)
  872. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  873. #endif
  874. //#define PROBING_FANS_OFF // Turn fans off when probing
  875. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  876. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  877. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  878. // :{ 0:'Low', 1:'High' }
  879. #define X_ENABLE_ON 0
  880. #define Y_ENABLE_ON 0
  881. #define Z_ENABLE_ON 0
  882. #define E_ENABLE_ON 0 // For all extruders
  883. // Disables axis stepper immediately when it's not being used.
  884. // WARNING: When motors turn off there is a chance of losing position accuracy!
  885. #define DISABLE_X false
  886. #define DISABLE_Y false
  887. #define DISABLE_Z false
  888. // Warn on display about possibly reduced accuracy
  889. //#define DISABLE_REDUCED_ACCURACY_WARNING
  890. // @section extruder
  891. #define DISABLE_E false // For all extruders
  892. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  893. // @section machine
  894. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  895. #define INVERT_X_DIR true
  896. #define INVERT_Y_DIR true
  897. #define INVERT_Z_DIR false
  898. // @section extruder
  899. // For direct drive extruder v9 set to true, for geared extruder set to false.
  900. #define INVERT_E0_DIR true
  901. #define INVERT_E1_DIR false
  902. #define INVERT_E2_DIR false
  903. #define INVERT_E3_DIR false
  904. #define INVERT_E4_DIR false
  905. #define INVERT_E5_DIR false
  906. // @section homing
  907. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  908. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  909. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  910. // Be sure you have this distance over your Z_MAX_POS in case.
  911. // Direction of endstops when homing; 1=MAX, -1=MIN
  912. // :[-1,1]
  913. #define X_HOME_DIR -1
  914. #define Y_HOME_DIR -1
  915. #define Z_HOME_DIR -1
  916. // @section machine
  917. // The size of the print bed
  918. #define X_BED_SIZE 205
  919. #define Y_BED_SIZE 205
  920. // Travel limits (mm) after homing, corresponding to endstop positions.
  921. #define X_MIN_POS 0
  922. #define Y_MIN_POS 0
  923. #define Z_MIN_POS 0
  924. #define X_MAX_POS X_BED_SIZE
  925. #define Y_MAX_POS Y_BED_SIZE
  926. #define Z_MAX_POS 185
  927. /**
  928. * Software Endstops
  929. *
  930. * - Prevent moves outside the set machine bounds.
  931. * - Individual axes can be disabled, if desired.
  932. * - X and Y only apply to Cartesian robots.
  933. * - Use 'M211' to set software endstops on/off or report current state
  934. */
  935. // Min software endstops constrain movement within minimum coordinate bounds
  936. #define MIN_SOFTWARE_ENDSTOPS
  937. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  938. #define MIN_SOFTWARE_ENDSTOP_X
  939. #define MIN_SOFTWARE_ENDSTOP_Y
  940. #define MIN_SOFTWARE_ENDSTOP_Z
  941. #endif
  942. // Max software endstops constrain movement within maximum coordinate bounds
  943. #define MAX_SOFTWARE_ENDSTOPS
  944. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  945. #define MAX_SOFTWARE_ENDSTOP_X
  946. #define MAX_SOFTWARE_ENDSTOP_Y
  947. #define MAX_SOFTWARE_ENDSTOP_Z
  948. #endif
  949. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  950. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  951. #endif
  952. /**
  953. * Filament Runout Sensors
  954. * Mechanical or opto endstops are used to check for the presence of filament.
  955. *
  956. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  957. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  958. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  959. */
  960. //#define FILAMENT_RUNOUT_SENSOR
  961. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  962. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  963. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
  964. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  965. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  966. // Set one or more commands to execute on filament runout.
  967. // (After 'M412 H' Marlin will ask the host to handle the process.)
  968. #define FILAMENT_RUNOUT_SCRIPT "M600"
  969. // After a runout is detected, continue printing this length of filament
  970. // before executing the runout script. Useful for a sensor at the end of
  971. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  972. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  973. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  974. // Enable this option to use an encoder disc that toggles the runout pin
  975. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  976. // large enough to avoid false positives.)
  977. //#define FILAMENT_MOTION_SENSOR
  978. #endif
  979. #endif
  980. //===========================================================================
  981. //=============================== Bed Leveling ==============================
  982. //===========================================================================
  983. // @section calibrate
  984. /**
  985. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  986. * and behavior of G29 will change depending on your selection.
  987. *
  988. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  989. *
  990. * - AUTO_BED_LEVELING_3POINT
  991. * Probe 3 arbitrary points on the bed (that aren't collinear)
  992. * You specify the XY coordinates of all 3 points.
  993. * The result is a single tilted plane. Best for a flat bed.
  994. *
  995. * - AUTO_BED_LEVELING_LINEAR
  996. * Probe several points in a grid.
  997. * You specify the rectangle and the density of sample points.
  998. * The result is a single tilted plane. Best for a flat bed.
  999. *
  1000. * - AUTO_BED_LEVELING_BILINEAR
  1001. * Probe several points in a grid.
  1002. * You specify the rectangle and the density of sample points.
  1003. * The result is a mesh, best for large or uneven beds.
  1004. *
  1005. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1006. * A comprehensive bed leveling system combining the features and benefits
  1007. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1008. * Validation and Mesh Editing systems.
  1009. *
  1010. * - MESH_BED_LEVELING
  1011. * Probe a grid manually
  1012. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1013. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1014. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1015. * With an LCD controller the process is guided step-by-step.
  1016. */
  1017. //#define AUTO_BED_LEVELING_3POINT
  1018. //#define AUTO_BED_LEVELING_LINEAR
  1019. //#define AUTO_BED_LEVELING_BILINEAR
  1020. //#define AUTO_BED_LEVELING_UBL
  1021. //#define MESH_BED_LEVELING
  1022. /**
  1023. * Normally G28 leaves leveling disabled on completion. Enable
  1024. * this option to have G28 restore the prior leveling state.
  1025. */
  1026. //#define RESTORE_LEVELING_AFTER_G28
  1027. /**
  1028. * Enable detailed logging of G28, G29, M48, etc.
  1029. * Turn on with the command 'M111 S32'.
  1030. * NOTE: Requires a lot of PROGMEM!
  1031. */
  1032. //#define DEBUG_LEVELING_FEATURE
  1033. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1034. // Gradually reduce leveling correction until a set height is reached,
  1035. // at which point movement will be level to the machine's XY plane.
  1036. // The height can be set with M420 Z<height>
  1037. #define ENABLE_LEVELING_FADE_HEIGHT
  1038. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1039. // split up moves into short segments like a Delta. This follows the
  1040. // contours of the bed more closely than edge-to-edge straight moves.
  1041. #define SEGMENT_LEVELED_MOVES
  1042. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1043. /**
  1044. * Enable the G26 Mesh Validation Pattern tool.
  1045. */
  1046. //#define G26_MESH_VALIDATION
  1047. #if ENABLED(G26_MESH_VALIDATION)
  1048. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1049. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1050. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1051. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1052. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1053. #endif
  1054. #endif
  1055. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1056. // Set the number of grid points per dimension.
  1057. #define GRID_MAX_POINTS_X 3
  1058. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1059. // Probe along the Y axis, advancing X after each column
  1060. //#define PROBE_Y_FIRST
  1061. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1062. // Beyond the probed grid, continue the implied tilt?
  1063. // Default is to maintain the height of the nearest edge.
  1064. //#define EXTRAPOLATE_BEYOND_GRID
  1065. //
  1066. // Experimental Subdivision of the grid by Catmull-Rom method.
  1067. // Synthesizes intermediate points to produce a more detailed mesh.
  1068. //
  1069. //#define ABL_BILINEAR_SUBDIVISION
  1070. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1071. // Number of subdivisions between probe points
  1072. #define BILINEAR_SUBDIVISIONS 3
  1073. #endif
  1074. #endif
  1075. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1076. //===========================================================================
  1077. //========================= Unified Bed Leveling ============================
  1078. //===========================================================================
  1079. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1080. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1081. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1082. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1083. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1084. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1085. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1086. // as the Z-Height correction value.
  1087. #elif ENABLED(MESH_BED_LEVELING)
  1088. //===========================================================================
  1089. //=================================== Mesh ==================================
  1090. //===========================================================================
  1091. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1092. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1093. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1094. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1095. #endif // BED_LEVELING
  1096. /**
  1097. * Add a bed leveling sub-menu for ABL or MBL.
  1098. * Include a guided procedure if manual probing is enabled.
  1099. */
  1100. //#define LCD_BED_LEVELING
  1101. #if ENABLED(LCD_BED_LEVELING)
  1102. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1103. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1104. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1105. #endif
  1106. // Add a menu item to move between bed corners for manual bed adjustment
  1107. //#define LEVEL_BED_CORNERS
  1108. #if ENABLED(LEVEL_BED_CORNERS)
  1109. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1110. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
  1111. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1112. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1113. #endif
  1114. /**
  1115. * Commands to execute at the end of G29 probing.
  1116. * Useful to retract or move the Z probe out of the way.
  1117. */
  1118. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1119. // @section homing
  1120. // The center of the bed is at (X=0, Y=0)
  1121. //#define BED_CENTER_AT_0_0
  1122. // Manually set the home position. Leave these undefined for automatic settings.
  1123. // For DELTA this is the top-center of the Cartesian print volume.
  1124. //#define MANUAL_X_HOME_POS 0
  1125. //#define MANUAL_Y_HOME_POS 0
  1126. //#define MANUAL_Z_HOME_POS 0
  1127. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1128. //
  1129. // With this feature enabled:
  1130. //
  1131. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1132. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1133. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1134. // - Prevent Z homing when the Z probe is outside bed area.
  1135. //
  1136. //#define Z_SAFE_HOMING
  1137. #if ENABLED(Z_SAFE_HOMING)
  1138. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1139. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1140. #endif
  1141. // Homing speeds (mm/m)
  1142. #define HOMING_FEEDRATE_XY (50*60)
  1143. #define HOMING_FEEDRATE_Z (4*60)
  1144. // Validate that endstops are triggered on homing moves
  1145. #define VALIDATE_HOMING_ENDSTOPS
  1146. // @section calibrate
  1147. /**
  1148. * Bed Skew Compensation
  1149. *
  1150. * This feature corrects for misalignment in the XYZ axes.
  1151. *
  1152. * Take the following steps to get the bed skew in the XY plane:
  1153. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1154. * 2. For XY_DIAG_AC measure the diagonal A to C
  1155. * 3. For XY_DIAG_BD measure the diagonal B to D
  1156. * 4. For XY_SIDE_AD measure the edge A to D
  1157. *
  1158. * Marlin automatically computes skew factors from these measurements.
  1159. * Skew factors may also be computed and set manually:
  1160. *
  1161. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1162. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1163. *
  1164. * If desired, follow the same procedure for XZ and YZ.
  1165. * Use these diagrams for reference:
  1166. *
  1167. * Y Z Z
  1168. * ^ B-------C ^ B-------C ^ B-------C
  1169. * | / / | / / | / /
  1170. * | / / | / / | / /
  1171. * | A-------D | A-------D | A-------D
  1172. * +-------------->X +-------------->X +-------------->Y
  1173. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1174. */
  1175. //#define SKEW_CORRECTION
  1176. #if ENABLED(SKEW_CORRECTION)
  1177. // Input all length measurements here:
  1178. #define XY_DIAG_AC 282.8427124746
  1179. #define XY_DIAG_BD 282.8427124746
  1180. #define XY_SIDE_AD 200
  1181. // Or, set the default skew factors directly here
  1182. // to override the above measurements:
  1183. #define XY_SKEW_FACTOR 0.0
  1184. //#define SKEW_CORRECTION_FOR_Z
  1185. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1186. #define XZ_DIAG_AC 282.8427124746
  1187. #define XZ_DIAG_BD 282.8427124746
  1188. #define YZ_DIAG_AC 282.8427124746
  1189. #define YZ_DIAG_BD 282.8427124746
  1190. #define YZ_SIDE_AD 200
  1191. #define XZ_SKEW_FACTOR 0.0
  1192. #define YZ_SKEW_FACTOR 0.0
  1193. #endif
  1194. // Enable this option for M852 to set skew at runtime
  1195. //#define SKEW_CORRECTION_GCODE
  1196. #endif
  1197. //=============================================================================
  1198. //============================= Additional Features ===========================
  1199. //=============================================================================
  1200. // @section extras
  1201. /**
  1202. * EEPROM
  1203. *
  1204. * Persistent storage to preserve configurable settings across reboots.
  1205. *
  1206. * M500 - Store settings to EEPROM.
  1207. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1208. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1209. */
  1210. //#define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1211. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1212. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1213. #if ENABLED(EEPROM_SETTINGS)
  1214. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1215. #endif
  1216. //
  1217. // Host Keepalive
  1218. //
  1219. // When enabled Marlin will send a busy status message to the host
  1220. // every couple of seconds when it can't accept commands.
  1221. //
  1222. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1223. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1224. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1225. //
  1226. // M100 Free Memory Watcher
  1227. //
  1228. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1229. //
  1230. // G20/G21 Inch mode support
  1231. //
  1232. //#define INCH_MODE_SUPPORT
  1233. //
  1234. // M149 Set temperature units support
  1235. //
  1236. //#define TEMPERATURE_UNITS_SUPPORT
  1237. // @section temperature
  1238. // Preheat Constants
  1239. #define PREHEAT_1_LABEL "PLA"
  1240. #define PREHEAT_1_TEMP_HOTEND 200
  1241. #define PREHEAT_1_TEMP_BED 50
  1242. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1243. #define PREHEAT_2_LABEL "ABS"
  1244. #define PREHEAT_2_TEMP_HOTEND 245
  1245. #define PREHEAT_2_TEMP_BED 100
  1246. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1247. /**
  1248. * Nozzle Park
  1249. *
  1250. * Park the nozzle at the given XYZ position on idle or G27.
  1251. *
  1252. * The "P" parameter controls the action applied to the Z axis:
  1253. *
  1254. * P0 (Default) If Z is below park Z raise the nozzle.
  1255. * P1 Raise the nozzle always to Z-park height.
  1256. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1257. */
  1258. //#define NOZZLE_PARK_FEATURE
  1259. #if ENABLED(NOZZLE_PARK_FEATURE)
  1260. // Specify a park position as { X, Y, Z_raise }
  1261. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1262. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1263. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  1264. #endif
  1265. /**
  1266. * Clean Nozzle Feature -- EXPERIMENTAL
  1267. *
  1268. * Adds the G12 command to perform a nozzle cleaning process.
  1269. *
  1270. * Parameters:
  1271. * P Pattern
  1272. * S Strokes / Repetitions
  1273. * T Triangles (P1 only)
  1274. *
  1275. * Patterns:
  1276. * P0 Straight line (default). This process requires a sponge type material
  1277. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1278. * between the start / end points.
  1279. *
  1280. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1281. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1282. * Zig-zags are done in whichever is the narrower dimension.
  1283. * For example, "G12 P1 S1 T3" will execute:
  1284. *
  1285. * --
  1286. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1287. * | | / \ / \ / \ |
  1288. * A | | / \ / \ / \ |
  1289. * | | / \ / \ / \ |
  1290. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1291. * -- +--------------------------------+
  1292. * |________|_________|_________|
  1293. * T1 T2 T3
  1294. *
  1295. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1296. * "R" specifies the radius. "S" specifies the stroke count.
  1297. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1298. *
  1299. * Caveats: The ending Z should be the same as starting Z.
  1300. * Attention: EXPERIMENTAL. G-code arguments may change.
  1301. *
  1302. */
  1303. //#define NOZZLE_CLEAN_FEATURE
  1304. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1305. // Default number of pattern repetitions
  1306. #define NOZZLE_CLEAN_STROKES 12
  1307. // Default number of triangles
  1308. #define NOZZLE_CLEAN_TRIANGLES 3
  1309. // Specify positions as { X, Y, Z }
  1310. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1) }
  1311. #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) }
  1312. // Circular pattern radius
  1313. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1314. // Circular pattern circle fragments number
  1315. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1316. // Middle point of circle
  1317. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1318. // Move the nozzle to the initial position after cleaning
  1319. #define NOZZLE_CLEAN_GOBACK
  1320. // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
  1321. //#define NOZZLE_CLEAN_NO_Z
  1322. #endif
  1323. /**
  1324. * Print Job Timer
  1325. *
  1326. * Automatically start and stop the print job timer on M104/M109/M190.
  1327. *
  1328. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1329. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1330. * M190 (bed, wait) - high temp = start timer, low temp = none
  1331. *
  1332. * The timer can also be controlled with the following commands:
  1333. *
  1334. * M75 - Start the print job timer
  1335. * M76 - Pause the print job timer
  1336. * M77 - Stop the print job timer
  1337. */
  1338. #define PRINTJOB_TIMER_AUTOSTART
  1339. /**
  1340. * Print Counter
  1341. *
  1342. * Track statistical data such as:
  1343. *
  1344. * - Total print jobs
  1345. * - Total successful print jobs
  1346. * - Total failed print jobs
  1347. * - Total time printing
  1348. *
  1349. * View the current statistics with M78.
  1350. */
  1351. //#define PRINTCOUNTER
  1352. //=============================================================================
  1353. //============================= LCD and SD support ============================
  1354. //=============================================================================
  1355. // @section lcd
  1356. /**
  1357. * LCD LANGUAGE
  1358. *
  1359. * Select the language to display on the LCD. These languages are available:
  1360. *
  1361. * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
  1362. * ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1363. *
  1364. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1365. */
  1366. #define LCD_LANGUAGE en
  1367. /**
  1368. * LCD Character Set
  1369. *
  1370. * Note: This option is NOT applicable to Graphical Displays.
  1371. *
  1372. * All character-based LCDs provide ASCII plus one of these
  1373. * language extensions:
  1374. *
  1375. * - JAPANESE ... the most common
  1376. * - WESTERN ... with more accented characters
  1377. * - CYRILLIC ... for the Russian language
  1378. *
  1379. * To determine the language extension installed on your controller:
  1380. *
  1381. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1382. * - Click the controller to view the LCD menu
  1383. * - The LCD will display Japanese, Western, or Cyrillic text
  1384. *
  1385. * See http://marlinfw.org/docs/development/lcd_language.html
  1386. *
  1387. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1388. */
  1389. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1390. /**
  1391. * Info Screen Style (0:Classic, 1:Prusa)
  1392. *
  1393. * :[0:'Classic', 1:'Prusa']
  1394. */
  1395. #define LCD_INFO_SCREEN_STYLE 0
  1396. /**
  1397. * SD CARD
  1398. *
  1399. * SD Card support is disabled by default. If your controller has an SD slot,
  1400. * you must uncomment the following option or it won't work.
  1401. *
  1402. */
  1403. #define SDSUPPORT
  1404. /**
  1405. * SD CARD: SPI SPEED
  1406. *
  1407. * Enable one of the following items for a slower SPI transfer speed.
  1408. * This may be required to resolve "volume init" errors.
  1409. */
  1410. //#define SPI_SPEED SPI_HALF_SPEED
  1411. //#define SPI_SPEED SPI_QUARTER_SPEED
  1412. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1413. /**
  1414. * SD CARD: ENABLE CRC
  1415. *
  1416. * Use CRC checks and retries on the SD communication.
  1417. */
  1418. #define SD_CHECK_AND_RETRY
  1419. /**
  1420. * LCD Menu Items
  1421. *
  1422. * Disable all menus and only display the Status Screen, or
  1423. * just remove some extraneous menu items to recover space.
  1424. */
  1425. //#define NO_LCD_MENUS
  1426. //#define SLIM_LCD_MENUS
  1427. //
  1428. // ENCODER SETTINGS
  1429. //
  1430. // This option overrides the default number of encoder pulses needed to
  1431. // produce one step. Should be increased for high-resolution encoders.
  1432. //
  1433. //#define ENCODER_PULSES_PER_STEP 4
  1434. //
  1435. // Use this option to override the number of step signals required to
  1436. // move between next/prev menu items.
  1437. //
  1438. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1439. /**
  1440. * Encoder Direction Options
  1441. *
  1442. * Test your encoder's behavior first with both options disabled.
  1443. *
  1444. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1445. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1446. * Reversed Value Editing only? Enable BOTH options.
  1447. */
  1448. //
  1449. // This option reverses the encoder direction everywhere.
  1450. //
  1451. // Set this option if CLOCKWISE causes values to DECREASE
  1452. //
  1453. //#define REVERSE_ENCODER_DIRECTION
  1454. //
  1455. // This option reverses the encoder direction for navigating LCD menus.
  1456. //
  1457. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1458. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1459. //
  1460. //#define REVERSE_MENU_DIRECTION
  1461. //
  1462. // This option reverses the encoder direction for Select Screen.
  1463. //
  1464. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1465. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1466. //
  1467. //#define REVERSE_SELECT_DIRECTION
  1468. //
  1469. // Individual Axis Homing
  1470. //
  1471. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1472. //
  1473. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1474. //
  1475. // SPEAKER/BUZZER
  1476. //
  1477. // If you have a speaker that can produce tones, enable it here.
  1478. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1479. //
  1480. //#define SPEAKER
  1481. //
  1482. // The duration and frequency for the UI feedback sound.
  1483. // Set these to 0 to disable audio feedback in the LCD menus.
  1484. //
  1485. // Note: Test audio output with the G-Code:
  1486. // M300 S<frequency Hz> P<duration ms>
  1487. //
  1488. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1489. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1490. //=============================================================================
  1491. //======================== LCD / Controller Selection =========================
  1492. //======================== (Character-based LCDs) =========================
  1493. //=============================================================================
  1494. //
  1495. // RepRapDiscount Smart Controller.
  1496. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1497. //
  1498. // Note: Usually sold with a white PCB.
  1499. //
  1500. #define REPRAP_DISCOUNT_SMART_CONTROLLER
  1501. //
  1502. // Original RADDS LCD Display+Encoder+SDCardReader
  1503. // http://doku.radds.org/dokumentation/lcd-display/
  1504. //
  1505. //#define RADDS_DISPLAY
  1506. //
  1507. // ULTIMAKER Controller.
  1508. //
  1509. //#define ULTIMAKERCONTROLLER
  1510. //
  1511. // ULTIPANEL as seen on Thingiverse.
  1512. //
  1513. //#define ULTIPANEL
  1514. //
  1515. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1516. // http://reprap.org/wiki/PanelOne
  1517. //
  1518. //#define PANEL_ONE
  1519. //
  1520. // GADGETS3D G3D LCD/SD Controller
  1521. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1522. //
  1523. // Note: Usually sold with a blue PCB.
  1524. //
  1525. //#define G3D_PANEL
  1526. //
  1527. // RigidBot Panel V1.0
  1528. // http://www.inventapart.com/
  1529. //
  1530. //#define RIGIDBOT_PANEL
  1531. //
  1532. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1533. // https://www.aliexpress.com/item/32765887917.html
  1534. //
  1535. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1536. //
  1537. // ANET and Tronxy 20x4 Controller
  1538. //
  1539. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1540. // This LCD is known to be susceptible to electrical interference
  1541. // which scrambles the display. Pressing any button clears it up.
  1542. // This is a LCD2004 display with 5 analog buttons.
  1543. //
  1544. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1545. //
  1546. //#define ULTRA_LCD
  1547. //=============================================================================
  1548. //======================== LCD / Controller Selection =========================
  1549. //===================== (I2C and Shift-Register LCDs) =====================
  1550. //=============================================================================
  1551. //
  1552. // CONTROLLER TYPE: I2C
  1553. //
  1554. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1555. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1556. //
  1557. //
  1558. // Elefu RA Board Control Panel
  1559. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1560. //
  1561. //#define RA_CONTROL_PANEL
  1562. //
  1563. // Sainsmart (YwRobot) LCD Displays
  1564. //
  1565. // These require F.Malpartida's LiquidCrystal_I2C library
  1566. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1567. //
  1568. //#define LCD_SAINSMART_I2C_1602
  1569. //#define LCD_SAINSMART_I2C_2004
  1570. //
  1571. // Generic LCM1602 LCD adapter
  1572. //
  1573. //#define LCM1602
  1574. //
  1575. // PANELOLU2 LCD with status LEDs,
  1576. // separate encoder and click inputs.
  1577. //
  1578. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1579. // For more info: https://github.com/lincomatic/LiquidTWI2
  1580. //
  1581. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1582. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1583. //
  1584. //#define LCD_I2C_PANELOLU2
  1585. //
  1586. // Panucatt VIKI LCD with status LEDs,
  1587. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1588. //
  1589. //#define LCD_I2C_VIKI
  1590. //
  1591. // CONTROLLER TYPE: Shift register panels
  1592. //
  1593. //
  1594. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1595. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1596. //
  1597. //#define SAV_3DLCD
  1598. //
  1599. // 3-wire SR LCD with strobe using 74HC4094
  1600. // https://github.com/mikeshub/SailfishLCD
  1601. // Uses the code directly from Sailfish
  1602. //
  1603. //#define FF_INTERFACEBOARD
  1604. //=============================================================================
  1605. //======================= LCD / Controller Selection =======================
  1606. //========================= (Graphical LCDs) ========================
  1607. //=============================================================================
  1608. //
  1609. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1610. //
  1611. // IMPORTANT: The U8glib library is required for Graphical Display!
  1612. // https://github.com/olikraus/U8glib_Arduino
  1613. //
  1614. //
  1615. // RepRapDiscount FULL GRAPHIC Smart Controller
  1616. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1617. //
  1618. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1619. //
  1620. // ReprapWorld Graphical LCD
  1621. // https://reprapworld.com/?products_details&products_id/1218
  1622. //
  1623. //#define REPRAPWORLD_GRAPHICAL_LCD
  1624. //
  1625. // Activate one of these if you have a Panucatt Devices
  1626. // Viki 2.0 or mini Viki with Graphic LCD
  1627. // http://panucatt.com
  1628. //
  1629. //#define VIKI2
  1630. //#define miniVIKI
  1631. //
  1632. // MakerLab Mini Panel with graphic
  1633. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1634. //
  1635. //#define MINIPANEL
  1636. //
  1637. // MaKr3d Makr-Panel with graphic controller and SD support.
  1638. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1639. //
  1640. //#define MAKRPANEL
  1641. //
  1642. // Adafruit ST7565 Full Graphic Controller.
  1643. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1644. //
  1645. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1646. //
  1647. // BQ LCD Smart Controller shipped by
  1648. // default with the BQ Hephestos 2 and Witbox 2.
  1649. //
  1650. //#define BQ_LCD_SMART_CONTROLLER
  1651. //
  1652. // Cartesio UI
  1653. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1654. //
  1655. //#define CARTESIO_UI
  1656. //
  1657. // LCD for Melzi Card with Graphical LCD
  1658. //
  1659. //#define LCD_FOR_MELZI
  1660. //
  1661. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1662. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1663. //
  1664. //#define ULTI_CONTROLLER
  1665. //
  1666. // MKS MINI12864 with graphic controller and SD support
  1667. // https://reprap.org/wiki/MKS_MINI_12864
  1668. //
  1669. //#define MKS_MINI_12864
  1670. //
  1671. // FYSETC variant of the MINI12864 graphic controller with SD support
  1672. // https://wiki.fysetc.com/Mini12864_Panel/
  1673. //
  1674. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1675. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1676. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1677. //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight
  1678. //
  1679. // Factory display for Creality CR-10
  1680. // https://www.aliexpress.com/item/32833148327.html
  1681. //
  1682. // This is RAMPS-compatible using a single 10-pin connector.
  1683. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1684. //
  1685. //#define CR10_STOCKDISPLAY
  1686. //
  1687. // Ender-2 OEM display, a variant of the MKS_MINI_12864
  1688. //
  1689. //#define ENDER2_STOCKDISPLAY
  1690. //
  1691. // ANET and Tronxy Graphical Controller
  1692. //
  1693. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1694. // A clone of the RepRapDiscount full graphics display but with
  1695. // different pins/wiring (see pins_ANET_10.h).
  1696. //
  1697. //#define ANET_FULL_GRAPHICS_LCD
  1698. //
  1699. // AZSMZ 12864 LCD with SD
  1700. // https://www.aliexpress.com/item/32837222770.html
  1701. //
  1702. //#define AZSMZ_12864
  1703. //
  1704. // Silvergate GLCD controller
  1705. // http://github.com/android444/Silvergate
  1706. //
  1707. //#define SILVER_GATE_GLCD_CONTROLLER
  1708. //=============================================================================
  1709. //============================== OLED Displays ==============================
  1710. //=============================================================================
  1711. //
  1712. // SSD1306 OLED full graphics generic display
  1713. //
  1714. //#define U8GLIB_SSD1306
  1715. //
  1716. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1717. //
  1718. //#define SAV_3DGLCD
  1719. #if ENABLED(SAV_3DGLCD)
  1720. #define U8GLIB_SSD1306
  1721. //#define U8GLIB_SH1106
  1722. #endif
  1723. //
  1724. // TinyBoy2 128x64 OLED / Encoder Panel
  1725. //
  1726. //#define OLED_PANEL_TINYBOY2
  1727. //
  1728. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1729. // http://reprap.org/wiki/MKS_12864OLED
  1730. //
  1731. // Tiny, but very sharp OLED display
  1732. //
  1733. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1734. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1735. //
  1736. // Einstart S OLED SSD1306
  1737. //
  1738. //#define U8GLIB_SH1106_EINSTART
  1739. //
  1740. // Overlord OLED display/controller with i2c buzzer and LEDs
  1741. //
  1742. //#define OVERLORD_OLED
  1743. //=============================================================================
  1744. //========================== Extensible UI Displays ===========================
  1745. //=============================================================================
  1746. //
  1747. // DGUS Touch Display with DWIN OS. (Choose one.)
  1748. //
  1749. //#define DGUS_LCD_UI_ORIGIN
  1750. //#define DGUS_LCD_UI_FYSETC
  1751. //#define DGUS_LCD_UI_HIPRECY
  1752. //
  1753. // Touch-screen LCD for Malyan M200 printers
  1754. //
  1755. //#define MALYAN_LCD
  1756. //
  1757. // Touch UI for FTDI EVE (FT800/FT810) displays
  1758. // See Configuration_adv.h for all configuration options.
  1759. //
  1760. //#define TOUCH_UI_FTDI_EVE
  1761. //
  1762. // Third-party or vendor-customized controller interfaces.
  1763. // Sources should be installed in 'src/lcd/extensible_ui'.
  1764. //
  1765. //#define EXTENSIBLE_UI
  1766. //=============================================================================
  1767. //=============================== Graphical TFTs ==============================
  1768. //=============================================================================
  1769. //
  1770. // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
  1771. //
  1772. //#define FSMC_GRAPHICAL_TFT
  1773. //=============================================================================
  1774. //============================ Other Controllers ============================
  1775. //=============================================================================
  1776. //
  1777. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  1778. //
  1779. //#define TOUCH_BUTTONS
  1780. #if ENABLED(TOUCH_BUTTONS)
  1781. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  1782. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  1783. #define XPT2046_X_CALIBRATION 12316
  1784. #define XPT2046_Y_CALIBRATION -8981
  1785. #define XPT2046_X_OFFSET -43
  1786. #define XPT2046_Y_OFFSET 257
  1787. #endif
  1788. //
  1789. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1790. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1791. //
  1792. //#define REPRAPWORLD_KEYPAD
  1793. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  1794. //=============================================================================
  1795. //=============================== Extra Features ==============================
  1796. //=============================================================================
  1797. // @section extras
  1798. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1799. //#define FAST_PWM_FAN
  1800. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1801. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1802. // is too low, you should also increment SOFT_PWM_SCALE.
  1803. //#define FAN_SOFT_PWM
  1804. // Incrementing this by 1 will double the software PWM frequency,
  1805. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1806. // However, control resolution will be halved for each increment;
  1807. // at zero value, there are 128 effective control positions.
  1808. // :[0,1,2,3,4,5,6,7]
  1809. #define SOFT_PWM_SCALE 0
  1810. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1811. // be used to mitigate the associated resolution loss. If enabled,
  1812. // some of the PWM cycles are stretched so on average the desired
  1813. // duty cycle is attained.
  1814. //#define SOFT_PWM_DITHER
  1815. // Temperature status LEDs that display the hotend and bed temperature.
  1816. // If all hotends, bed temperature, and target temperature are under 54C
  1817. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1818. //#define TEMP_STAT_LEDS
  1819. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1820. //#define SF_ARC_FIX
  1821. // Support for the BariCUDA Paste Extruder
  1822. //#define BARICUDA
  1823. // Support for BlinkM/CyzRgb
  1824. //#define BLINKM
  1825. // Support for PCA9632 PWM LED driver
  1826. //#define PCA9632
  1827. // Support for PCA9533 PWM LED driver
  1828. // https://github.com/mikeshub/SailfishRGB_LED
  1829. //#define PCA9533
  1830. /**
  1831. * RGB LED / LED Strip Control
  1832. *
  1833. * Enable support for an RGB LED connected to 5V digital pins, or
  1834. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1835. *
  1836. * Adds the M150 command to set the LED (or LED strip) color.
  1837. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1838. * luminance values can be set from 0 to 255.
  1839. * For Neopixel LED an overall brightness parameter is also available.
  1840. *
  1841. * *** CAUTION ***
  1842. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1843. * as the Arduino cannot handle the current the LEDs will require.
  1844. * Failure to follow this precaution can destroy your Arduino!
  1845. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1846. * more current than the Arduino 5V linear regulator can produce.
  1847. * *** CAUTION ***
  1848. *
  1849. * LED Type. Enable only one of the following two options.
  1850. *
  1851. */
  1852. //#define RGB_LED
  1853. //#define RGBW_LED
  1854. #if EITHER(RGB_LED, RGBW_LED)
  1855. //#define RGB_LED_R_PIN 34
  1856. //#define RGB_LED_G_PIN 43
  1857. //#define RGB_LED_B_PIN 35
  1858. //#define RGB_LED_W_PIN -1
  1859. #endif
  1860. // Support for Adafruit Neopixel LED driver
  1861. //#define NEOPIXEL_LED
  1862. #if ENABLED(NEOPIXEL_LED)
  1863. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1864. #define NEOPIXEL_PIN 4 // LED driving pin
  1865. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  1866. //#define NEOPIXEL2_PIN 5
  1867. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
  1868. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1869. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1870. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1871. // Use a single Neopixel LED for static (background) lighting
  1872. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  1873. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  1874. #endif
  1875. /**
  1876. * Printer Event LEDs
  1877. *
  1878. * During printing, the LEDs will reflect the printer status:
  1879. *
  1880. * - Gradually change from blue to violet as the heated bed gets to target temp
  1881. * - Gradually change from violet to red as the hotend gets to temperature
  1882. * - Change to white to illuminate work surface
  1883. * - Change to green once print has finished
  1884. * - Turn off after the print has finished and the user has pushed a button
  1885. */
  1886. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  1887. #define PRINTER_EVENT_LEDS
  1888. #endif
  1889. /**
  1890. * R/C SERVO support
  1891. * Sponsored by TrinityLabs, Reworked by codexmas
  1892. */
  1893. /**
  1894. * Number of servos
  1895. *
  1896. * For some servo-related options NUM_SERVOS will be set automatically.
  1897. * Set this manually if there are extra servos needing manual control.
  1898. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1899. */
  1900. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1901. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  1902. // 300ms is a good value but you can try less delay.
  1903. // If the servo can't reach the requested position, increase it.
  1904. #define SERVO_DELAY { 300 }
  1905. // Only power servos during movement, otherwise leave off to prevent jitter
  1906. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1907. // Allow servo angle to be edited and saved to EEPROM
  1908. //#define EDITABLE_SERVO_ANGLES