My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Du kan inte välja fler än 25 ämnen Ämnen måste starta med en bokstav eller siffra, kan innehålla bindestreck ('-') och vara max 35 tecken långa.

pins_OMCA.h 3.6KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Open Motion controller with enable based extruders (Final!)
  24. *
  25. * ATMega644
  26. *
  27. * +---\/---+
  28. * (D 0) PB0 1| |40 PA0 (AI 0 / D31)
  29. * (D 1) PB1 2| |39 PA1 (AI 1 / D30)
  30. * INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
  31. * PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
  32. * PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
  33. * MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
  34. * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
  35. * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
  36. * RST 9| |32 AREF
  37. * VCC 10| |31 GND
  38. * GND 11| |30 AVCC
  39. * XTAL2 12| |29 PC7 (D 23)
  40. * XTAL1 13| |28 PC6 (D 22)
  41. * RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
  42. * TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
  43. * INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
  44. * INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
  45. * PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
  46. * PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
  47. * PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
  48. * +--------+
  49. *
  50. * REF http://sanguino.cc/hardware
  51. */
  52. #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
  53. #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)"
  54. #endif
  55. #define BOARD_NAME "Final OMCA"
  56. //
  57. // Limit Switches
  58. //
  59. #define X_STOP_PIN 0
  60. #define Y_STOP_PIN 1
  61. #define Z_STOP_PIN 2
  62. //
  63. // Steppers
  64. //
  65. #define X_STEP_PIN 26
  66. #define X_DIR_PIN 25
  67. #define X_ENABLE_PIN 10
  68. #define Y_STEP_PIN 28
  69. #define Y_DIR_PIN 27
  70. #define Y_ENABLE_PIN 10
  71. #define Z_STEP_PIN 23
  72. #define Z_DIR_PIN 22
  73. #define Z_ENABLE_PIN 10
  74. #define E0_STEP_PIN 24
  75. #define E0_DIR_PIN 21
  76. #define E0_ENABLE_PIN 10
  77. #define E1_STEP_PIN -1 // 21
  78. #define E1_DIR_PIN -1 // 20
  79. #define E1_ENABLE_PIN -1 // 19
  80. #define E2_STEP_PIN -1 // 21
  81. #define E2_DIR_PIN -1 // 20
  82. #define E2_ENABLE_PIN -1 // 18
  83. //
  84. // Temperature Sensors
  85. //
  86. #define TEMP_0_PIN 0 // Analog Input
  87. #define TEMP_1_PIN 1 // Analog Input
  88. #define TEMP_BED_PIN 2 // Analog Input (1,2 or I2C)
  89. //
  90. // Heaters / Fans
  91. //
  92. #define HEATER_0_PIN 3 // DONE PWM on RIGHT connector
  93. #define HEATER_BED_PIN 4
  94. #define FAN_PIN 14 // PWM on MIDDLE connector
  95. //
  96. // Misc. Functions
  97. //
  98. #define SDSS 11
  99. #define I2C_SCL 16
  100. #define I2C_SDA 17
  101. // future proofing
  102. #define __FS 20
  103. #define __FD 19
  104. #define __GS 18
  105. #define __GD 13
  106. #define UNUSED_PWM 14 // PWM on LEFT connector