123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- *
- */
-
- /**
- * Open Motion controller with enable based extruders (Final!)
- *
- * ATMega644
- *
- * +---\/---+
- * (D 0) PB0 1| |40 PA0 (AI 0 / D31)
- * (D 1) PB1 2| |39 PA1 (AI 1 / D30)
- * INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
- * PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
- * PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
- * MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
- * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
- * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
- * RST 9| |32 AREF
- * VCC 10| |31 GND
- * GND 11| |30 AVCC
- * XTAL2 12| |29 PC7 (D 23)
- * XTAL1 13| |28 PC6 (D 22)
- * RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
- * TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
- * INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
- * INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
- * PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
- * PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
- * PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
- * +--------+
- *
- * REF http://sanguino.cc/hardware
- */
-
- #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
- #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)"
- #endif
-
- #define BOARD_NAME "Final OMCA"
-
- #define X_STEP_PIN 26
- #define X_DIR_PIN 25
- #define X_ENABLE_PIN 10
- #define X_STOP_PIN 0
-
- #define Y_STEP_PIN 28
- #define Y_DIR_PIN 27
- #define Y_ENABLE_PIN 10
- #define Y_STOP_PIN 1
-
- #define Z_STEP_PIN 23
- #define Z_DIR_PIN 22
- #define Z_ENABLE_PIN 10
- #define Z_STOP_PIN 2
-
- #define E0_STEP_PIN 24
- #define E0_DIR_PIN 21
- #define E0_ENABLE_PIN 10
-
- // future proofing
- #define __FS 20
- #define __FD 19
- #define __GS 18
- #define __GD 13
-
- #define UNUSED_PWM 14 // PWM on LEFT connector
-
- #define E1_STEP_PIN -1 // 21
- #define E1_DIR_PIN -1 // 20
- #define E1_ENABLE_PIN -1 // 19
-
- #define E2_STEP_PIN -1 // 21
- #define E2_DIR_PIN -1 // 20
- #define E2_ENABLE_PIN -1 // 18
-
- #define SDSS 11
- #define FAN_PIN 14 // PWM on MIDDLE connector
-
- #define HEATER_0_PIN 3 // DONE PWM on RIGHT connector
- #define HEATER_BED_PIN 4
-
- #define TEMP_0_PIN 0 // Analog Input
- #define TEMP_1_PIN 1 // Analog Input
- #define TEMP_BED_PIN 2 // Analog Input (1,2 or I2C)
-
- #define I2C_SCL 16
- #define I2C_SDA 17
|