123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <https://www.gnu.org/licenses/>.
- *
- */
- #pragma once
-
- /**
- * FLSUN HiSpeed V1 (STM32F103VET6) board pin assignments
- * FLSun Hispeed (clone MKS_Robin_miniV2) board.
- *
- * MKS Robin Mini USB uses UART3 (PB10-TX, PB11-RX)
- * #define SERIAL_PORT_2 3
- */
-
- #if NOT_TARGET(__STM32F1__, STM32F1xx)
- #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
- #elif HAS_MULTI_HOTEND || E_STEPPERS > 1
- #error "FLSUN HiSpeedV1 only supports 1 hotend / E stepper."
- #endif
-
- #define BOARD_INFO_NAME "FLSun HiSpeedV1"
- #define BOARD_WEBSITE_URL "github.com/Foxies-CSTL"
-
- #define BOARD_NO_NATIVE_USB
-
- // Avoid conflict with TIMER_SERVO when using the STM32 HAL
- #define TEMP_TIMER 5
-
- //
- // Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
- //
- #define DISABLE_DEBUG
-
- //
- // EEPROM
- //
- #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
- #define FLASH_EEPROM_EMULATION
- #define EEPROM_PAGE_SIZE (0x800U) // 2K
- #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
- #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE // 2K
- #endif
-
- //
- // SPI
- // Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface.
- //
- #define SD_SCK_PIN PB13 // SPI2
- #define SD_MISO_PIN PB14 // SPI2
- #define SD_MOSI_PIN PB15 // SPI2
- #define SPI_DEVICE 2
-
- // SPI Flash
- #define SPI_FLASH
- #if ENABLED(SPI_FLASH)
- // SPI 2
- #define SPI_FLASH_CS_PIN PB12 // SPI2_NSS / Flash chip-select
- #define SPI_FLASH_MOSI_PIN PB15
- #define SPI_FLASH_MISO_PIN PB14
- #define SPI_FLASH_SCK_PIN PB13
- #define SPI_FLASH_SIZE 0x1000000 // 16MB
- #endif
-
- //
- // Servos
- //
- //#define SERVO0_PIN PA8 // use IO0 to enable BLTOUCH support/remove Mks_Wifi
-
- //
- // Limit Switches
- //
- #define X_STOP_PIN PA15 // -X
- #define Y_STOP_PIN PA12 // -Y
- #define Z_MIN_PIN PA11 // -Z
- #define Z_MAX_PIN PC4 // +Z
-
- #ifndef FIL_RUNOUT_PIN
- #define FIL_RUNOUT_PIN PA4 // MT_DET
- #endif
-
- //
- // Steppers
- //
- #define X_ENABLE_PIN PE4 // X_EN
- #define X_STEP_PIN PE3 // X_STEP
- #define X_DIR_PIN PE2 // X_DIR
-
- #define Y_ENABLE_PIN PE1 // Y_EN
- #define Y_STEP_PIN PE0 // Y_STEP
- #define Y_DIR_PIN PB9 // Y_DIR
-
- #define Z_ENABLE_PIN PB8 // Z_EN
- #define Z_STEP_PIN PB5 // Z_STEP
- #define Z_DIR_PIN PB4 // Z_DIR
-
- #define E0_ENABLE_PIN PB3 // E0_EN
- #define E0_STEP_PIN PD6 // E0_STEP
- #define E0_DIR_PIN PD3 // E0_DIR
-
- /**
- * FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers.
- * Several wiring options are provided below, defaulting to
- * to the most compatible.
- */
- #if HAS_TMC_UART
- // SoftwareSerial with one pin per driver
- // Compatible with TMC2208 and TMC2209 drivers
- #define X_SERIAL_TX_PIN PA10 // RXD1
- #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
- #define Y_SERIAL_TX_PIN PA9 // TXD1
- #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
- #define Z_SERIAL_TX_PIN PC7 // IO1
- #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
- #define TMC_BAUD_RATE 19200
- #else
- // Motor current PWM pins
- #define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY
- #define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z
- #define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
- #ifndef DEFAULT_PWM_MOTOR_CURRENT
- #define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
- #endif
-
- /**
- * MKS Robin_Wifi or another ESP8266 module
- *
- * __ESP(M1)__ -J1-
- * GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
- * | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
- * IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
- * IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
- * IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
- * | nc | | nc | (01) WIFI_CTRL (PA5)
- * RX| 21 | | nc |
- * TX| 22 | | 01 |RST
- *  ̄ ̄ AE ̄ ̄
- */
- // Module ESP-WIFI
- #define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
- #define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
- #define ESP_WIFI_MODULE_RESET_PIN PA5 // WIFI CTRL/RST
- #define ESP_WIFI_MODULE_ENABLE_PIN -1
- #define ESP_WIFI_MODULE_TXD_PIN PA9 // MKS or ESP WIFI RX PIN
- #define ESP_WIFI_MODULE_RXD_PIN PA10 // MKS or ESP WIFI TX PIN
- #endif
-
- //
- // EXTRUDER
- //
- #if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209)
- #define E0_SERIAL_TX_PIN PA8 // IO0
- #define E0_SERIAL_RX_PIN PA8 // IO0
- #define TMC_BAUD_RATE 19200
- #else
- // Motor current PWM pins
- #define MOTOR_CURRENT_PWM_E_PIN PB0 // VREF1 CONTROL E
- #define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
- #ifndef DEFAULT_PWM_MOTOR_CURRENT
- #define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
- #endif
- #endif
-
- //
- // Temperature Sensors (THM)
- //
- #define TEMP_0_PIN PC1 // TEMP_E0
- #define TEMP_BED_PIN PC0 // TEMP_BED
-
- //
- // Heaters / Fans
- //
- #define HEATER_0_PIN PC3 // HEATER_E0
- #define HEATER_BED_PIN PA0 // HEATER_BED-WKUP
-
- #define FAN_PIN PB1 // E_FAN
-
- //
- // Misc. Functions
- //
- #if ENABLED(BACKUP_POWER_SUPPLY)
- #define POWER_LOSS_PIN PA2 // PW_DET (UPS) MKSPWC
- #else
- //#define POWER_LOSS_PIN PA1 // PW_SO
- #endif
-
- /**
- * Connector J2
- * -------
- * DIO O|1 2|O 3v3
- * CSK O|3 5|O GND
- * RST O|5 6|O GND
- * -------
- */
- //#define SW_DIO PA13
- //#define SW_CLK PA14
- //#define SW_RST NRST // (14)
-
- //
- // Power Supply Control
- //
- #if ENABLED(PSU_CONTROL)
- #define KILL_PIN PA2 // PW_DET
- #define KILL_PIN_STATE HIGH
- //#define PS_ON_PIN PA3 // PW_CN /PW_OFF
- #endif
-
- #if HAS_TFT_LVGL_UI
- #define MT_DET_1_PIN PA4 // MT_DET
- #define MT_DET_2_PIN PE6
- #define MT_DET_PIN_STATE LOW
- #endif
-
- //
- // LED / NEOPixel
- //
- //#define LED_PIN PB2 // BOOT1
-
- #if ENABLED(NEOPIXEL_LED)
- #define LED_PWM PC7 // IO1
- #ifndef NEOPIXEL_PIN
- #define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1 PIN
- #endif
- #endif
-
- //
- // SD Card
- //
- #ifndef SDCARD_CONNECTION
- #define SDCARD_CONNECTION ONBOARD
- #endif
-
- // Use the on-board card socket labeled SD_Extender
- #if SD_CONNECTION_IS(CUSTOM_CABLE)
- #define SD_SCK_PIN PC12
- #define SD_MISO_PIN PC8
- #define SD_MOSI_PIN PD2
- #define SD_SS_PIN -1
- #define SD_DETECT_PIN PD12 // SD_CD (if -1 no detection)
- #else
- #define SDIO_SUPPORT
- #define SDIO_CLOCK 4500000 // 4.5 MHz
- #define SDIO_READ_RETRIES 16
- #define ONBOARD_SPI_DEVICE 1 // SPI1
- #define ONBOARD_SD_CS_PIN PC11
- #define SD_DETECT_PIN -1 // SD_CD (-1 active refresh)
- #endif
-
- //
- // LCD / Controller
- //
- #ifndef BEEPER_PIN
- #define BEEPER_PIN PC5
- #endif
-
- #if ENABLED(SPEAKER) && BEEPER_PIN == PC5
- #error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER."
- #endif
-
- //
- // TFT with FSMC interface
- //
- #if HAS_FSMC_TFT
- /**
- * Note: MKS Robin TFT screens use various TFT controllers
- * Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240)
- * ILI9488 is not supported
- * Define init sequences for other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp
- *
- * If the screen stays white, disable 'LCD_RESET_PIN'
- * to let the bootloader init the screen.
- *
- * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu
- * because Marlin uses the reset as a failsafe to revive a glitchy LCD.
- */
- //#define TFT_RESET_PIN PC6 // FSMC_RST
- #define TFT_BACKLIGHT_PIN PD13
-
- #define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
- #define FSMC_DMA_DEV DMA2
- #define FSMC_DMA_CHANNEL DMA_CH5
-
- #define FSMC_CS_PIN PD7 // NE4
- #define FSMC_RS_PIN PD11 // A0
-
- #define TFT_CS_PIN FSMC_CS_PIN
- #define TFT_RS_PIN FSMC_RS_PIN
-
- #ifdef TFT_CLASSIC_UI
- #define TFT_MARLINBG_COLOR 0x3186 // Grey
- #define TFT_MARLINUI_COLOR 0xC7B6 // Green
- #define TFT_BTARROWS_COLOR 0xDEE6 // Yellow
- #define TFT_BTOKMENU_COLOR 0x145F // Cyan
- #endif
- #define TFT_BUFFER_SIZE 14400
-
- #elif HAS_GRAPHICAL_TFT
-
- #define TFT_RESET_PIN PC6
- #define TFT_BACKLIGHT_PIN PD13
- #define TFT_CS_PIN PD7 // NE4
- #define TFT_RS_PIN PD11 // A0
-
- #endif
-
- #if NEED_TOUCH_PINS
- #define TOUCH_CS_PIN PC2 // SPI2_NSS
- #define TOUCH_SCK_PIN PB13 // SPI2_SCK
- #define TOUCH_MISO_PIN PB14 // SPI2_MISO
- #define TOUCH_MOSI_PIN PB15 // SPI2_MOSI
- #define TOUCH_INT_PIN -1
- #endif
|