My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Ви не можете вибрати більше 25 тем Теми мають розпочинатися з літери або цифри, можуть містити дефіси (-) і не повинні перевищувати 35 символів.

Configuration_adv.h 171KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510610710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916016116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321421521621721821922022122222322422522622722822923023123223323423523623723823924024124224324424524624724824925025125225325425525625725825926026126226326426526626726826927027127227327427527627727827928028128228328428528628728828929029129229329429529629729829930030130230330430530630730830931031131231331431531631731831932032132232332432532632732832933033133233333433533633733833934034134234334434534634734834935035135235335435535635735835936036136236336436536636736836937037137237337437537637737837938038138238338438538638738838939039139239339439539639739839940040140240340440540640740840941041141241341441541641741841942042142242342442542642742842943043143243343443543643743843944044144244344444544644744844945045145245345445545645745845946046146246346446546646746846947047147247347447547647747847948048148248348448548648748848949049149249349449549649749849950050150250350450550650750850951051151251351451551651751851952052152252352452552652752852953053153253353453553653753853954054154254354454554654754854955055155255355455555655755855956056156256356456556656756856957057157257357457557657757857958058158258358458558658758858959059159259359459559659759859960060160260360460560660760860961061161261361461561661761861962062162262362462562662762862963063163263363463563663763863964064164264364464564664764864965065165265365465565665765865966066166266366466566666766866967067167267367467567667767867968068168268368468568668768868969069169269369469569669769869970070170270370470570670770870971071171271371471571671771871972072172272372472572672772872973073173273373473573673773873974074174274374474574674774874975075175275375475575675775875976076176276376476576676776876977077177277377477577677777877978078178278378478578678778878979079179279379479579679779879980080180280380480580680780880981081181281381481581681781881982082182282382482582682782882983083183283383483583683783883984084184284384484584684784884985085185285385485585685785885986086186286386486586686786886987087187287387487587687787887988088188288388488588688788888989089189289389489589689789889990090190290390490590690790890991091191291391491591691791891992092192292392492592692792892993093193293393493593693793893994094194294394494594694794894995095195295395495595695795895996096196296396496596696796896997097197297397497597697797897998098198298398498598698798898999099199299399499599699799899910001001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025102610271028102910301031103210331034103510361037103810391040104110421043104410451046104710481049105010511052105310541055105610571058105910601061106210631064106510661067106810691070107110721073107410751076107710781079108010811082108310841085108610871088108910901091109210931094109510961097109810991100110111021103110411051106110711081109111011111112111311141115111611171118111911201121112211231124112511261127112811291130113111321133113411351136113711381139114011411142114311441145114611471148114911501151115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175117611771178117911801181118211831184118511861187118811891190119111921193119411951196119711981199120012011202120312041205120612071208120912101211121212131214121512161217121812191220122112221223122412251226122712281229123012311232123312341235123612371238123912401241124212431244124512461247124812491250125112521253125412551256125712581259126012611262126312641265126612671268126912701271127212731274127512761277127812791280128112821283128412851286128712881289129012911292129312941295129612971298129913001301130213031304130513061307130813091310131113121313131413151316131713181319132013211322132313241325132613271328132913301331133213331334133513361337133813391340134113421343134413451346134713481349135013511352135313541355135613571358135913601361136213631364136513661367136813691370137113721373137413751376137713781379138013811382138313841385138613871388138913901391139213931394139513961397139813991400140114021403140414051406140714081409141014111412141314141415141614171418141914201421142214231424142514261427142814291430143114321433143414351436143714381439144014411442144314441445144614471448144914501451145214531454145514561457145814591460146114621463146414651466146714681469147014711472147314741475147614771478147914801481148214831484148514861487148814891490149114921493149414951496149714981499150015011502150315041505150615071508150915101511151215131514151515161517151815191520152115221523152415251526152715281529153015311532153315341535153615371538153915401541154215431544154515461547154815491550155115521553155415551556155715581559156015611562156315641565156615671568156915701571157215731574157515761577157815791580158115821583158415851586158715881589159015911592159315941595159615971598159916001601160216031604160516061607160816091610161116121613161416151616161716181619162016211622162316241625162616271628162916301631163216331634163516361637163816391640164116421643164416451646164716481649165016511652165316541655165616571658165916601661166216631664166516661667166816691670167116721673167416751676167716781679168016811682168316841685168616871688168916901691169216931694169516961697169816991700170117021703170417051706170717081709171017111712171317141715171617171718171917201721172217231724172517261727172817291730173117321733173417351736173717381739174017411742174317441745174617471748174917501751175217531754175517561757175817591760176117621763176417651766176717681769177017711772177317741775177617771778177917801781178217831784178517861787178817891790179117921793179417951796179717981799180018011802180318041805180618071808180918101811181218131814181518161817181818191820182118221823182418251826182718281829183018311832183318341835183618371838183918401841184218431844184518461847184818491850185118521853185418551856185718581859186018611862186318641865186618671868186918701871187218731874187518761877187818791880188118821883188418851886188718881889189018911892189318941895189618971898189919001901190219031904190519061907190819091910191119121913191419151916191719181919192019211922192319241925192619271928192919301931193219331934193519361937193819391940194119421943194419451946194719481949195019511952195319541955195619571958195919601961196219631964196519661967196819691970197119721973197419751976197719781979198019811982198319841985198619871988198919901991199219931994199519961997199819992000200120022003200420052006200720082009201020112012201320142015201620172018201920202021202220232024202520262027202820292030203120322033203420352036203720382039204020412042204320442045204620472048204920502051205220532054205520562057205820592060206120622063206420652066206720682069207020712072207320742075207620772078207920802081208220832084208520862087208820892090209120922093209420952096209720982099210021012102210321042105210621072108210921102111211221132114211521162117211821192120212121222123212421252126212721282129213021312132213321342135213621372138213921402141214221432144214521462147214821492150215121522153215421552156215721582159216021612162216321642165216621672168216921702171217221732174217521762177217821792180218121822183218421852186218721882189219021912192219321942195219621972198219922002201220222032204220522062207220822092210221122122213221422152216221722182219222022212222222322242225222622272228222922302231223222332234223522362237223822392240224122422243224422452246224722482249225022512252225322542255225622572258225922602261226222632264226522662267226822692270227122722273227422752276227722782279228022812282228322842285228622872288228922902291229222932294229522962297229822992300230123022303230423052306230723082309231023112312231323142315231623172318231923202321232223232324232523262327232823292330233123322333233423352336233723382339234023412342234323442345234623472348234923502351235223532354235523562357235823592360236123622363236423652366236723682369237023712372237323742375237623772378237923802381238223832384238523862387238823892390239123922393239423952396239723982399240024012402240324042405240624072408240924102411241224132414241524162417241824192420242124222423242424252426242724282429243024312432243324342435243624372438243924402441244224432444244524462447244824492450245124522453245424552456245724582459246024612462246324642465246624672468246924702471247224732474247524762477247824792480248124822483248424852486248724882489249024912492249324942495249624972498249925002501250225032504250525062507250825092510251125122513251425152516251725182519252025212522252325242525252625272528252925302531253225332534253525362537253825392540254125422543254425452546254725482549255025512552255325542555255625572558255925602561256225632564256525662567256825692570257125722573257425752576257725782579258025812582258325842585258625872588258925902591259225932594259525962597259825992600260126022603260426052606260726082609261026112612261326142615261626172618261926202621262226232624262526262627262826292630263126322633263426352636263726382639264026412642264326442645264626472648264926502651265226532654265526562657265826592660266126622663266426652666266726682669267026712672267326742675267626772678267926802681268226832684268526862687268826892690269126922693269426952696269726982699270027012702270327042705270627072708270927102711271227132714271527162717271827192720272127222723272427252726272727282729273027312732273327342735273627372738273927402741274227432744274527462747274827492750275127522753275427552756275727582759276027612762276327642765276627672768276927702771277227732774277527762777277827792780278127822783278427852786278727882789279027912792279327942795279627972798279928002801280228032804280528062807280828092810281128122813281428152816281728182819282028212822282328242825282628272828282928302831283228332834283528362837283828392840284128422843284428452846284728482849285028512852285328542855285628572858285928602861286228632864286528662867286828692870287128722873287428752876287728782879288028812882288328842885288628872888288928902891289228932894289528962897289828992900290129022903290429052906290729082909291029112912291329142915291629172918291929202921292229232924292529262927292829292930293129322933293429352936293729382939294029412942294329442945294629472948294929502951295229532954295529562957295829592960296129622963296429652966296729682969297029712972297329742975297629772978297929802981298229832984298529862987298829892990299129922993299429952996299729982999300030013002300330043005300630073008300930103011301230133014301530163017301830193020302130223023302430253026302730283029303030313032303330343035303630373038303930403041304230433044304530463047304830493050305130523053305430553056305730583059306030613062306330643065306630673068306930703071307230733074307530763077307830793080308130823083308430853086308730883089309030913092309330943095309630973098309931003101310231033104310531063107310831093110311131123113311431153116311731183119312031213122312331243125312631273128312931303131313231333134313531363137313831393140314131423143314431453146314731483149315031513152315331543155315631573158315931603161316231633164316531663167316831693170317131723173317431753176317731783179318031813182318331843185318631873188318931903191319231933194319531963197319831993200320132023203320432053206320732083209321032113212321332143215321632173218321932203221322232233224322532263227322832293230323132323233323432353236323732383239324032413242324332443245324632473248324932503251325232533254325532563257325832593260326132623263326432653266326732683269327032713272327332743275327632773278327932803281328232833284328532863287328832893290329132923293329432953296329732983299330033013302330333043305330633073308330933103311331233133314331533163317331833193320332133223323332433253326332733283329333033313332333333343335333633373338333933403341334233433344334533463347334833493350335133523353335433553356335733583359336033613362336333643365336633673368336933703371337233733374337533763377337833793380338133823383338433853386338733883389339033913392339333943395339633973398339934003401340234033404340534063407340834093410341134123413341434153416341734183419342034213422342334243425342634273428342934303431343234333434343534363437343834393440344134423443344434453446344734483449345034513452345334543455345634573458345934603461346234633464346534663467346834693470347134723473347434753476347734783479348034813482348334843485348634873488348934903491349234933494349534963497349834993500350135023503350435053506350735083509351035113512351335143515351635173518351935203521352235233524352535263527352835293530353135323533353435353536353735383539354035413542354335443545354635473548354935503551355235533554355535563557355835593560356135623563356435653566356735683569357035713572357335743575357635773578357935803581358235833584358535863587358835893590359135923593359435953596359735983599360036013602360336043605360636073608360936103611361236133614361536163617361836193620362136223623362436253626362736283629363036313632363336343635363636373638363936403641364236433644364536463647364836493650365136523653365436553656365736583659366036613662366336643665366636673668366936703671367236733674367536763677367836793680368136823683368436853686368736883689369036913692369336943695369636973698369937003701370237033704370537063707370837093710371137123713371437153716371737183719372037213722372337243725372637273728372937303731373237333734373537363737373837393740374137423743374437453746374737483749375037513752375337543755375637573758375937603761376237633764376537663767376837693770377137723773377437753776377737783779378037813782378337843785378637873788378937903791379237933794379537963797379837993800380138023803380438053806380738083809381038113812381338143815381638173818381938203821382238233824382538263827382838293830383138323833383438353836383738383839384038413842384338443845384638473848384938503851385238533854385538563857385838593860386138623863386438653866386738683869387038713872387338743875387638773878387938803881388238833884388538863887388838893890389138923893389438953896389738983899390039013902390339043905390639073908390939103911391239133914391539163917391839193920392139223923392439253926392739283929393039313932393339343935393639373938393939403941394239433944394539463947394839493950395139523953395439553956395739583959396039613962396339643965396639673968396939703971397239733974397539763977397839793980398139823983398439853986398739883989399039913992399339943995399639973998399940004001400240034004400540064007400840094010401140124013401440154016401740184019402040214022402340244025402640274028402940304031403240334034403540364037403840394040404140424043404440454046404740484049405040514052405340544055405640574058405940604061406240634064406540664067406840694070407140724073407440754076407740784079408040814082408340844085408640874088408940904091409240934094409540964097409840994100410141024103410441054106410741084109411041114112411341144115411641174118411941204121412241234124412541264127412841294130413141324133413441354136413741384139414041414142414341444145414641474148414941504151415241534154415541564157415841594160416141624163416441654166416741684169417041714172417341744175417641774178417941804181418241834184418541864187418841894190419141924193419441954196419741984199420042014202420342044205420642074208420942104211421242134214421542164217421842194220422142224223422442254226422742284229423042314232423342344235423642374238423942404241424242434244
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration_adv.h
  25. *
  26. * Advanced settings.
  27. * Only change these if you know exactly what you're doing.
  28. * Some of these settings can damage your printer if improperly set!
  29. *
  30. * Basic settings can be found in Configuration.h
  31. */
  32. #define CONFIGURATION_ADV_H_VERSION 02010100
  33. //===========================================================================
  34. //============================= Thermal Settings ============================
  35. //===========================================================================
  36. // @section temperature
  37. /**
  38. * Thermocouple sensors are quite sensitive to noise. Any noise induced in
  39. * the sensor wires, such as by stepper motor wires run in parallel to them,
  40. * may result in the thermocouple sensor reporting spurious errors. This
  41. * value is the number of errors which can occur in a row before the error
  42. * is reported. This allows us to ignore intermittent error conditions while
  43. * still detecting an actual failure, which should result in a continuous
  44. * stream of errors from the sensor.
  45. *
  46. * Set this value to 0 to fail on the first error to occur.
  47. */
  48. #define THERMOCOUPLE_MAX_ERRORS 15
  49. //
  50. // Custom Thermistor 1000 parameters
  51. //
  52. #if TEMP_SENSOR_0 == 1000
  53. #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  54. #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  55. #define HOTEND0_BETA 3950 // Beta value
  56. #define HOTEND0_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  57. #endif
  58. #if TEMP_SENSOR_1 == 1000
  59. #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  60. #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  61. #define HOTEND1_BETA 3950 // Beta value
  62. #define HOTEND1_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  63. #endif
  64. #if TEMP_SENSOR_2 == 1000
  65. #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  66. #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  67. #define HOTEND2_BETA 3950 // Beta value
  68. #define HOTEND2_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  69. #endif
  70. #if TEMP_SENSOR_3 == 1000
  71. #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  72. #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  73. #define HOTEND3_BETA 3950 // Beta value
  74. #define HOTEND3_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  75. #endif
  76. #if TEMP_SENSOR_4 == 1000
  77. #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  78. #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  79. #define HOTEND4_BETA 3950 // Beta value
  80. #define HOTEND4_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  81. #endif
  82. #if TEMP_SENSOR_5 == 1000
  83. #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  84. #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  85. #define HOTEND5_BETA 3950 // Beta value
  86. #define HOTEND5_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  87. #endif
  88. #if TEMP_SENSOR_6 == 1000
  89. #define HOTEND6_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  90. #define HOTEND6_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  91. #define HOTEND6_BETA 3950 // Beta value
  92. #define HOTEND6_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  93. #endif
  94. #if TEMP_SENSOR_7 == 1000
  95. #define HOTEND7_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  96. #define HOTEND7_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  97. #define HOTEND7_BETA 3950 // Beta value
  98. #define HOTEND7_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  99. #endif
  100. #if TEMP_SENSOR_BED == 1000
  101. #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  102. #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  103. #define BED_BETA 3950 // Beta value
  104. #define BED_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  105. #endif
  106. #if TEMP_SENSOR_CHAMBER == 1000
  107. #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  108. #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  109. #define CHAMBER_BETA 3950 // Beta value
  110. #define CHAMBER_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  111. #endif
  112. #if TEMP_SENSOR_COOLER == 1000
  113. #define COOLER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  114. #define COOLER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  115. #define COOLER_BETA 3950 // Beta value
  116. #define COOLER_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  117. #endif
  118. #if TEMP_SENSOR_PROBE == 1000
  119. #define PROBE_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  120. #define PROBE_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  121. #define PROBE_BETA 3950 // Beta value
  122. #define PROBE_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  123. #endif
  124. #if TEMP_SENSOR_BOARD == 1000
  125. #define BOARD_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  126. #define BOARD_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  127. #define BOARD_BETA 3950 // Beta value
  128. #define BOARD_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  129. #endif
  130. #if TEMP_SENSOR_REDUNDANT == 1000
  131. #define REDUNDANT_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  132. #define REDUNDANT_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  133. #define REDUNDANT_BETA 3950 // Beta value
  134. #define REDUNDANT_SH_C_COEFF 0 // Steinhart-Hart C coefficient
  135. #endif
  136. /**
  137. * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5).
  138. */
  139. //#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus.
  140. //#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board.
  141. //#define MAX31865_SENSOR_WIRES_1 2
  142. //#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz.
  143. //#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors.
  144. //#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature.
  145. //#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals.
  146. //#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439).
  147. //#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings.
  148. //#define MAX31865_WIRE_OHMS_1 0.0f
  149. /**
  150. * Hephestos 2 24V heated bed upgrade kit.
  151. * https://store.bq.com/en/heated-bed-kit-hephestos2
  152. */
  153. //#define HEPHESTOS2_HEATED_BED_KIT
  154. #if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
  155. #undef TEMP_SENSOR_BED
  156. #define TEMP_SENSOR_BED 70
  157. #define HEATER_BED_INVERTING true
  158. #endif
  159. //
  160. // Heated Bed Bang-Bang options
  161. //
  162. #if DISABLED(PIDTEMPBED)
  163. #define BED_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
  164. #if ENABLED(BED_LIMIT_SWITCHING)
  165. #define BED_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > BED_HYSTERESIS
  166. #endif
  167. #endif
  168. //
  169. // Heated Chamber options
  170. //
  171. #if DISABLED(PIDTEMPCHAMBER)
  172. #define CHAMBER_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
  173. #if ENABLED(CHAMBER_LIMIT_SWITCHING)
  174. #define CHAMBER_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > CHAMBER_HYSTERESIS
  175. #endif
  176. #endif
  177. #if TEMP_SENSOR_CHAMBER
  178. //#define HEATER_CHAMBER_PIN P2_04 // Required heater on/off pin (example: SKR 1.4 Turbo HE1 plug)
  179. //#define HEATER_CHAMBER_INVERTING false
  180. //#define FAN1_PIN -1 // Remove the fan signal on pin P2_04 (example: SKR 1.4 Turbo HE1 plug)
  181. //#define CHAMBER_FAN // Enable a fan on the chamber
  182. #if ENABLED(CHAMBER_FAN)
  183. //#define CHAMBER_FAN_INDEX 2 // Index of a fan to repurpose as the chamber fan. (Default: first unused fan)
  184. #define CHAMBER_FAN_MODE 2 // Fan control mode: 0=Static; 1=Linear increase when temp is higher than target; 2=V-shaped curve; 3=similar to 1 but fan is always on.
  185. #if CHAMBER_FAN_MODE == 0
  186. #define CHAMBER_FAN_BASE 255 // Chamber fan PWM (0-255)
  187. #elif CHAMBER_FAN_MODE == 1
  188. #define CHAMBER_FAN_BASE 128 // Base chamber fan PWM (0-255); turns on when chamber temperature is above the target
  189. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C above target
  190. #elif CHAMBER_FAN_MODE == 2
  191. #define CHAMBER_FAN_BASE 128 // Minimum chamber fan PWM (0-255)
  192. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C difference from target
  193. #elif CHAMBER_FAN_MODE == 3
  194. #define CHAMBER_FAN_BASE 128 // Base chamber fan PWM (0-255)
  195. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C above target
  196. #endif
  197. #endif
  198. //#define CHAMBER_VENT // Enable a servo-controlled vent on the chamber
  199. #if ENABLED(CHAMBER_VENT)
  200. #define CHAMBER_VENT_SERVO_NR 1 // Index of the vent servo
  201. #define HIGH_EXCESS_HEAT_LIMIT 5 // How much above target temp to consider there is excess heat in the chamber
  202. #define LOW_EXCESS_HEAT_LIMIT 3
  203. #define MIN_COOLING_SLOPE_TIME_CHAMBER_VENT 20
  204. #define MIN_COOLING_SLOPE_DEG_CHAMBER_VENT 1.5
  205. #endif
  206. #endif
  207. //
  208. // Laser Cooler options
  209. //
  210. #if TEMP_SENSOR_COOLER
  211. #define COOLER_MINTEMP 8 // (°C)
  212. #define COOLER_MAXTEMP 26 // (°C)
  213. #define COOLER_DEFAULT_TEMP 16 // (°C)
  214. #define TEMP_COOLER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
  215. #define COOLER_PIN 8 // Laser cooler on/off pin used to control power to the cooling element (e.g., TEC, External chiller via relay)
  216. #define COOLER_INVERTING false
  217. #define TEMP_COOLER_PIN 15 // Laser/Cooler temperature sensor pin. ADC is required.
  218. #define COOLER_FAN // Enable a fan on the cooler, Fan# 0,1,2,3 etc.
  219. #define COOLER_FAN_INDEX 0 // FAN number 0, 1, 2 etc. e.g.
  220. #if ENABLED(COOLER_FAN)
  221. #define COOLER_FAN_BASE 100 // Base Cooler fan PWM (0-255); turns on when Cooler temperature is above the target
  222. #define COOLER_FAN_FACTOR 25 // PWM increase per °C above target
  223. #endif
  224. #endif
  225. //
  226. // Motherboard Sensor options
  227. //
  228. #if TEMP_SENSOR_BOARD
  229. #define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
  230. #define BOARD_MINTEMP 8 // (°C)
  231. #define BOARD_MAXTEMP 70 // (°C)
  232. #ifndef TEMP_BOARD_PIN
  233. //#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
  234. #endif
  235. #endif
  236. /**
  237. * Thermal Protection provides additional protection to your printer from damage
  238. * and fire. Marlin always includes safe min and max temperature ranges which
  239. * protect against a broken or disconnected thermistor wire.
  240. *
  241. * The issue: If a thermistor falls out, it will report the much lower
  242. * temperature of the air in the room, and the the firmware will keep
  243. * the heater on.
  244. *
  245. * The solution: Once the temperature reaches the target, start observing.
  246. * If the temperature stays too far below the target (hysteresis) for too
  247. * long (period), the firmware will halt the machine as a safety precaution.
  248. *
  249. * If you get false positives for "Thermal Runaway", increase
  250. * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  251. */
  252. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  253. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  254. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  255. //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
  256. #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
  257. //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
  258. #endif
  259. /**
  260. * Whenever an M104, M109, or M303 increases the target temperature, the
  261. * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
  262. * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
  263. * requires a hard reset. This test restarts with any M104/M109/M303, but only
  264. * if the current temperature is far enough below the target for a reliable
  265. * test.
  266. *
  267. * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
  268. * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
  269. * below 2.
  270. */
  271. #define WATCH_TEMP_PERIOD 20 // Seconds
  272. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  273. #endif
  274. /**
  275. * Thermal Protection parameters for the bed are just as above for hotends.
  276. */
  277. #if ENABLED(THERMAL_PROTECTION_BED)
  278. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  279. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  280. /**
  281. * As described above, except for the bed (M140/M190/M303).
  282. */
  283. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  284. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  285. #endif
  286. /**
  287. * Thermal Protection parameters for the heated chamber.
  288. */
  289. #if ENABLED(THERMAL_PROTECTION_CHAMBER)
  290. #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
  291. #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
  292. /**
  293. * Heated chamber watch settings (M141/M191).
  294. */
  295. #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
  296. #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
  297. #endif
  298. /**
  299. * Thermal Protection parameters for the laser cooler.
  300. */
  301. #if ENABLED(THERMAL_PROTECTION_COOLER)
  302. #define THERMAL_PROTECTION_COOLER_PERIOD 10 // Seconds
  303. #define THERMAL_PROTECTION_COOLER_HYSTERESIS 3 // Degrees Celsius
  304. /**
  305. * Laser cooling watch settings (M143/M193).
  306. */
  307. #define WATCH_COOLER_TEMP_PERIOD 60 // Seconds
  308. #define WATCH_COOLER_TEMP_INCREASE 3 // Degrees Celsius
  309. #endif
  310. #if ANY(THERMAL_PROTECTION_HOTENDS, THERMAL_PROTECTION_BED, THERMAL_PROTECTION_CHAMBER, THERMAL_PROTECTION_COOLER)
  311. /**
  312. * Thermal Protection Variance Monitor - EXPERIMENTAL.
  313. * Kill the machine on a stuck temperature sensor. Disable if you get false positives.
  314. */
  315. //#define THERMAL_PROTECTION_VARIANCE_MONITOR // Detect a sensor malfunction preventing temperature updates
  316. #endif
  317. #if ENABLED(PIDTEMP)
  318. // Add an experimental additional term to the heater power, proportional to the extrusion speed.
  319. // A well-chosen Kc value should add just enough power to melt the increased material volume.
  320. //#define PID_EXTRUSION_SCALING
  321. #if ENABLED(PID_EXTRUSION_SCALING)
  322. #define DEFAULT_Kc (100) // heating power = Kc * e_speed
  323. #define LPQ_MAX_LEN 50
  324. #endif
  325. /**
  326. * Add an experimental additional term to the heater power, proportional to the fan speed.
  327. * A well-chosen Kf value should add just enough power to compensate for power-loss from the cooling fan.
  328. * You can either just add a constant compensation with the DEFAULT_Kf value
  329. * or follow the instruction below to get speed-dependent compensation.
  330. *
  331. * Constant compensation (use only with fanspeeds of 0% and 100%)
  332. * ---------------------------------------------------------------------
  333. * A good starting point for the Kf-value comes from the calculation:
  334. * kf = (power_fan * eff_fan) / power_heater * 255
  335. * where eff_fan is between 0.0 and 1.0, based on fan-efficiency and airflow to the nozzle / heater.
  336. *
  337. * Example:
  338. * Heater: 40W, Fan: 0.1A * 24V = 2.4W, eff_fan = 0.8
  339. * Kf = (2.4W * 0.8) / 40W * 255 = 12.24
  340. *
  341. * Fan-speed dependent compensation
  342. * --------------------------------
  343. * 1. To find a good Kf value, set the hotend temperature, wait for it to settle, and enable the fan (100%).
  344. * Make sure PID_FAN_SCALING_LIN_FACTOR is 0 and PID_FAN_SCALING_ALTERNATIVE_DEFINITION is not enabled.
  345. * If you see the temperature drop repeat the test, increasing the Kf value slowly, until the temperature
  346. * drop goes away. If the temperature overshoots after enabling the fan, the Kf value is too big.
  347. * 2. Note the Kf-value for fan-speed at 100%
  348. * 3. Determine a good value for PID_FAN_SCALING_MIN_SPEED, which is around the speed, where the fan starts moving.
  349. * 4. Repeat step 1. and 2. for this fan speed.
  350. * 5. Enable PID_FAN_SCALING_ALTERNATIVE_DEFINITION and enter the two identified Kf-values in
  351. * PID_FAN_SCALING_AT_FULL_SPEED and PID_FAN_SCALING_AT_MIN_SPEED. Enter the minimum speed in PID_FAN_SCALING_MIN_SPEED
  352. */
  353. //#define PID_FAN_SCALING
  354. #if ENABLED(PID_FAN_SCALING)
  355. //#define PID_FAN_SCALING_ALTERNATIVE_DEFINITION
  356. #if ENABLED(PID_FAN_SCALING_ALTERNATIVE_DEFINITION)
  357. // The alternative definition is used for an easier configuration.
  358. // Just figure out Kf at fullspeed (255) and PID_FAN_SCALING_MIN_SPEED.
  359. // DEFAULT_Kf and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.
  360. #define PID_FAN_SCALING_AT_FULL_SPEED 13.0 //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_Kf
  361. #define PID_FAN_SCALING_AT_MIN_SPEED 6.0 //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
  362. #define PID_FAN_SCALING_MIN_SPEED 10.0 // Minimum fan speed at which to enable PID_FAN_SCALING
  363. #define DEFAULT_Kf (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
  364. #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_Kf)/255.0
  365. #else
  366. #define PID_FAN_SCALING_LIN_FACTOR (0) // Power loss due to cooling = Kf * (fan_speed)
  367. #define DEFAULT_Kf 10 // A constant value added to the PID-tuner
  368. #define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
  369. #endif
  370. #endif
  371. #endif
  372. /**
  373. * Automatic Temperature Mode
  374. *
  375. * Dynamically adjust the hotend target temperature based on planned E moves.
  376. *
  377. * (Contrast with PID_EXTRUSION_SCALING, which tracks E movement and adjusts PID
  378. * behavior using an additional kC value.)
  379. *
  380. * Autotemp is calculated by (mintemp + factor * mm_per_sec), capped to maxtemp.
  381. *
  382. * Enable Autotemp Mode with M104/M109 F<factor> S<mintemp> B<maxtemp>.
  383. * Disable by sending M104/M109 with no F parameter (or F0 with AUTOTEMP_PROPORTIONAL).
  384. */
  385. #define AUTOTEMP
  386. #if ENABLED(AUTOTEMP)
  387. #define AUTOTEMP_OLDWEIGHT 0.98 // Factor used to weight previous readings (0.0 < value < 1.0)
  388. // Turn on AUTOTEMP on M104/M109 by default using proportions set here
  389. //#define AUTOTEMP_PROPORTIONAL
  390. #if ENABLED(AUTOTEMP_PROPORTIONAL)
  391. #define AUTOTEMP_MIN_P 0 // (°C) Added to the target temperature
  392. #define AUTOTEMP_MAX_P 5 // (°C) Added to the target temperature
  393. #define AUTOTEMP_FACTOR_P 1 // Apply this F parameter by default (overridden by M104/M109 F)
  394. #endif
  395. #endif
  396. // Show Temperature ADC value
  397. // Enable for M105 to include ADC values read from temperature sensors.
  398. //#define SHOW_TEMP_ADC_VALUES
  399. /**
  400. * High Temperature Thermistor Support
  401. *
  402. * Thermistors able to support high temperature tend to have a hard time getting
  403. * good readings at room and lower temperatures. This means TEMP_SENSOR_X_RAW_LO_TEMP
  404. * will probably be caught when the heating element first turns on during the
  405. * preheating process, which will trigger a min_temp_error as a safety measure
  406. * and force stop everything.
  407. * To circumvent this limitation, we allow for a preheat time (during which,
  408. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  409. * aberrant readings.
  410. *
  411. * If you want to enable this feature for your hotend thermistor(s)
  412. * uncomment and set values > 0 in the constants below
  413. */
  414. // The number of consecutive low temperature errors that can occur
  415. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  416. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  417. // The number of milliseconds a hotend will preheat before starting to check
  418. // the temperature. This value should NOT be set to the time it takes the
  419. // hot end to reach the target temperature, but the time it takes to reach
  420. // the minimum temperature your thermistor can read. The lower the better/safer.
  421. // This shouldn't need to be more than 30 seconds (30000)
  422. //#define MILLISECONDS_PREHEAT_TIME 0
  423. // @section extruder
  424. // Extruder runout prevention.
  425. // If the machine is idle and the temperature over MINTEMP
  426. // then extrude some filament every couple of SECONDS.
  427. //#define EXTRUDER_RUNOUT_PREVENT
  428. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  429. #define EXTRUDER_RUNOUT_MINTEMP 190
  430. #define EXTRUDER_RUNOUT_SECONDS 30
  431. #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/min)
  432. #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm)
  433. #endif
  434. /**
  435. * Hotend Idle Timeout
  436. * Prevent filament in the nozzle from charring and causing a critical jam.
  437. */
  438. //#define HOTEND_IDLE_TIMEOUT
  439. #if ENABLED(HOTEND_IDLE_TIMEOUT)
  440. #define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection
  441. #define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
  442. #define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
  443. #define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
  444. #endif
  445. // @section temperature
  446. // Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
  447. // The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
  448. #define TEMP_SENSOR_AD595_OFFSET 0.0
  449. #define TEMP_SENSOR_AD595_GAIN 1.0
  450. #define TEMP_SENSOR_AD8495_OFFSET 0.0
  451. #define TEMP_SENSOR_AD8495_GAIN 1.0
  452. /**
  453. * Controller Fan
  454. * To cool down the stepper drivers and MOSFETs.
  455. *
  456. * The fan turns on automatically whenever any driver is enabled and turns
  457. * off (or reduces to idle speed) shortly after drivers are turned off.
  458. */
  459. //#define USE_CONTROLLER_FAN
  460. #if ENABLED(USE_CONTROLLER_FAN)
  461. //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
  462. //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered
  463. //#define CONTROLLER_FAN_IGNORE_Z // Ignore Z stepper. Useful when stepper timeout is disabled.
  464. #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
  465. #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled
  466. #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled
  467. #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors
  468. // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
  469. //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
  470. //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
  471. #if ENABLED(CONTROLLER_FAN_EDITABLE)
  472. #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
  473. #endif
  474. #endif
  475. // When first starting the main fan, run it at full speed for the
  476. // given number of milliseconds. This gets the fan spinning reliably
  477. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  478. //#define FAN_KICKSTART_TIME 100
  479. // Some coolers may require a non-zero "off" state.
  480. //#define FAN_OFF_PWM 1
  481. /**
  482. * PWM Fan Scaling
  483. *
  484. * Define the min/max speeds for PWM fans (as set with M106).
  485. *
  486. * With these options the M106 0-255 value range is scaled to a subset
  487. * to ensure that the fan has enough power to spin, or to run lower
  488. * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
  489. * Value 0 always turns off the fan.
  490. *
  491. * Define one or both of these to override the default 0-255 range.
  492. */
  493. //#define FAN_MIN_PWM 50
  494. //#define FAN_MAX_PWM 128
  495. /**
  496. * Fan Fast PWM
  497. *
  498. * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
  499. * to produce a frequency as close as possible to the desired frequency.
  500. *
  501. * FAST_PWM_FAN_FREQUENCY
  502. * Set this to your desired frequency.
  503. * For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
  504. * i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
  505. * For non AVR, if left undefined this defaults to F = 1Khz.
  506. * This F value is only to protect the hardware from an absence of configuration
  507. * and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
  508. *
  509. * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
  510. * Setting very high frequencies can damage your hardware.
  511. *
  512. * USE_OCR2A_AS_TOP [undefined by default]
  513. * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
  514. * 16MHz MCUs: [62.5kHz, 31.4kHz (default), 7.8kHz, 3.92kHz, 1.95kHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz]
  515. * 20MHz MCUs: [78.1kHz, 39.2kHz (default), 9.77kHz, 4.9kHz, 2.44kHz, 1.22kHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz]
  516. * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of
  517. * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  518. * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  519. */
  520. //#define FAST_PWM_FAN // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  521. #if ENABLED(FAST_PWM_FAN)
  522. //#define FAST_PWM_FAN_FREQUENCY 31400 // Define here to override the defaults below
  523. //#define USE_OCR2A_AS_TOP
  524. #ifndef FAST_PWM_FAN_FREQUENCY
  525. #ifdef __AVR__
  526. #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
  527. #else
  528. #define FAST_PWM_FAN_FREQUENCY 1000U
  529. #endif
  530. #endif
  531. #endif
  532. /**
  533. * Use one of the PWM fans as a redundant part-cooling fan
  534. */
  535. //#define REDUNDANT_PART_COOLING_FAN 2 // Index of the fan to sync with FAN 0.
  536. // @section extruder
  537. /**
  538. * Extruder cooling fans
  539. *
  540. * Extruder auto fans automatically turn on when their extruders'
  541. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  542. *
  543. * Your board's pins file specifies the recommended pins. Override those here
  544. * or set to -1 to disable completely.
  545. *
  546. * Multiple extruders can be assigned to the same pin in which case
  547. * the fan will turn on when any selected extruder is above the threshold.
  548. */
  549. #define E0_AUTO_FAN_PIN -1
  550. #define E1_AUTO_FAN_PIN -1
  551. #define E2_AUTO_FAN_PIN -1
  552. #define E3_AUTO_FAN_PIN -1
  553. #define E4_AUTO_FAN_PIN -1
  554. #define E5_AUTO_FAN_PIN -1
  555. #define E6_AUTO_FAN_PIN -1
  556. #define E7_AUTO_FAN_PIN -1
  557. #define CHAMBER_AUTO_FAN_PIN -1
  558. #define COOLER_AUTO_FAN_PIN -1
  559. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  560. #define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed
  561. #define CHAMBER_AUTO_FAN_TEMPERATURE 30
  562. #define CHAMBER_AUTO_FAN_SPEED 255
  563. #define COOLER_AUTO_FAN_TEMPERATURE 18
  564. #define COOLER_AUTO_FAN_SPEED 255
  565. /**
  566. * Hotend Cooling Fans tachometers
  567. *
  568. * Define one or more tachometer pins to enable fan speed
  569. * monitoring, and reporting of fan speeds with M123.
  570. *
  571. * NOTE: Only works with fans up to 7000 RPM.
  572. */
  573. //#define FOURWIRES_FANS // Needed with AUTO_FAN when 4-wire PWM fans are installed
  574. //#define E0_FAN_TACHO_PIN -1
  575. //#define E0_FAN_TACHO_PULLUP
  576. //#define E0_FAN_TACHO_PULLDOWN
  577. //#define E1_FAN_TACHO_PIN -1
  578. //#define E1_FAN_TACHO_PULLUP
  579. //#define E1_FAN_TACHO_PULLDOWN
  580. //#define E2_FAN_TACHO_PIN -1
  581. //#define E2_FAN_TACHO_PULLUP
  582. //#define E2_FAN_TACHO_PULLDOWN
  583. //#define E3_FAN_TACHO_PIN -1
  584. //#define E3_FAN_TACHO_PULLUP
  585. //#define E3_FAN_TACHO_PULLDOWN
  586. //#define E4_FAN_TACHO_PIN -1
  587. //#define E4_FAN_TACHO_PULLUP
  588. //#define E4_FAN_TACHO_PULLDOWN
  589. //#define E5_FAN_TACHO_PIN -1
  590. //#define E5_FAN_TACHO_PULLUP
  591. //#define E5_FAN_TACHO_PULLDOWN
  592. //#define E6_FAN_TACHO_PIN -1
  593. //#define E6_FAN_TACHO_PULLUP
  594. //#define E6_FAN_TACHO_PULLDOWN
  595. //#define E7_FAN_TACHO_PIN -1
  596. //#define E7_FAN_TACHO_PULLUP
  597. //#define E7_FAN_TACHO_PULLDOWN
  598. /**
  599. * Part-Cooling Fan Multiplexer
  600. *
  601. * This feature allows you to digitally multiplex the fan output.
  602. * The multiplexer is automatically switched at tool-change.
  603. * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
  604. */
  605. #define FANMUX0_PIN -1
  606. #define FANMUX1_PIN -1
  607. #define FANMUX2_PIN -1
  608. /**
  609. * M355 Case Light on-off / brightness
  610. */
  611. //#define CASE_LIGHT_ENABLE
  612. #if ENABLED(CASE_LIGHT_ENABLE)
  613. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  614. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  615. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  616. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  617. //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
  618. //#define CASE_LIGHT_MAX_PWM 128 // Limit PWM duty cycle (0-255)
  619. //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
  620. #if ENABLED(NEOPIXEL_LED)
  621. //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light
  622. #endif
  623. #if EITHER(RGB_LED, RGBW_LED)
  624. //#define CASE_LIGHT_USE_RGB_LED // Use RGB / RGBW LED as case light
  625. #endif
  626. #if EITHER(CASE_LIGHT_USE_NEOPIXEL, CASE_LIGHT_USE_RGB_LED)
  627. #define CASE_LIGHT_DEFAULT_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
  628. #endif
  629. #endif
  630. // @section homing
  631. // If you want endstops to stay on (by default) even when not homing
  632. // enable this option. Override at any time with M120, M121.
  633. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  634. // @section extras
  635. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  636. // Employ an external closed loop controller. Override pins here if needed.
  637. //#define EXTERNAL_CLOSED_LOOP_CONTROLLER
  638. #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
  639. //#define CLOSED_LOOP_ENABLE_PIN -1
  640. //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
  641. #endif
  642. /**
  643. * Dual X Carriage
  644. *
  645. * This setup has two X carriages that can move independently, each with its own hotend.
  646. * The carriages can be used to print an object with two colors or materials, or in
  647. * "duplication mode" it can print two identical or X-mirrored objects simultaneously.
  648. * The inactive carriage is parked automatically to prevent oozing.
  649. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis.
  650. * By default the X2 stepper is assigned to the first unused E plug on the board.
  651. *
  652. * The following Dual X Carriage modes can be selected with M605 S<mode>:
  653. *
  654. * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel
  655. * results as long as it supports dual X-carriages. (M605 S0)
  656. *
  657. * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so
  658. * that additional slicer support is not required. (M605 S1)
  659. *
  660. * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with
  661. * the first X-carriage and extruder, to print 2 copies of the same object at the same time.
  662. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and
  663. * follow with M605 S2 to initiate duplicated movement.
  664. *
  665. * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates
  666. * the movement of the first except the second extruder is reversed in the X axis.
  667. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
  668. * follow with M605 S3 to initiate mirrored movement.
  669. */
  670. //#define DUAL_X_CARRIAGE
  671. #if ENABLED(DUAL_X_CARRIAGE)
  672. #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS
  673. #define X1_MAX_POS X_BED_SIZE // A max coordinate so the X1 carriage can't hit the parked X2 carriage
  674. #define X2_MIN_POS 80 // A min coordinate so the X2 carriage can't hit the parked X1 carriage
  675. #define X2_MAX_POS 353 // The max position of the X2 carriage, typically also the home position
  676. #define X2_HOME_DIR 1 // Set to 1. The X2 carriage always homes to the max endstop position
  677. #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS.
  678. // NOTE: For Dual X Carriage use M218 T1 Xn to override the X2_HOME_POS.
  679. // This allows recalibration of endstops distance without a rebuild.
  680. // Remember to set the second extruder's X-offset to 0 in your slicer.
  681. // This is the default power-up mode which can be changed later using M605 S<mode>.
  682. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
  683. // Default x offset in duplication mode (typically set to half print bed width)
  684. #define DEFAULT_DUPLICATION_X_OFFSET 100
  685. // Default action to execute following M605 mode change commands. Typically G28X to apply new mode.
  686. //#define EVENT_GCODE_IDEX_AFTER_MODECHANGE "G28X"
  687. #endif
  688. /**
  689. * Multi-Stepper / Multi-Endstop
  690. *
  691. * When X2_DRIVER_TYPE is defined, this indicates that the X and X2 motors work in tandem.
  692. * The following explanations for X also apply to Y and Z multi-stepper setups.
  693. * Endstop offsets may be changed by 'M666 X<offset> Y<offset> Z<offset>' and stored to EEPROM.
  694. *
  695. * - Enable INVERT_X2_VS_X_DIR if the X2 motor requires an opposite DIR signal from X.
  696. *
  697. * - Enable X_DUAL_ENDSTOPS if the second motor has its own endstop, with adjustable offset.
  698. *
  699. * - Extra endstops are included in the output of 'M119'.
  700. *
  701. * - Set X_DUAL_ENDSTOP_ADJUSTMENT to the known error in the X2 endstop.
  702. * Applied to the X2 motor on 'G28' / 'G28 X'.
  703. * Get the offset by homing X and measuring the error.
  704. * Also set with 'M666 X<offset>' and stored to EEPROM with 'M500'.
  705. *
  706. * - Use X2_USE_ENDSTOP to set the endstop plug by name. (_XMIN_, _XMAX_, _YMIN_, _YMAX_, _ZMIN_, _ZMAX_)
  707. */
  708. #if HAS_X2_STEPPER && DISABLED(DUAL_X_CARRIAGE)
  709. //#define INVERT_X2_VS_X_DIR // X2 direction signal is the opposite of X
  710. //#define X_DUAL_ENDSTOPS // X2 has its own endstop
  711. #if ENABLED(X_DUAL_ENDSTOPS)
  712. #define X2_USE_ENDSTOP _XMAX_ // X2 endstop board plug. Don't forget to enable USE_*_PLUG.
  713. #define X2_ENDSTOP_ADJUSTMENT 0 // X2 offset relative to X endstop
  714. #endif
  715. #endif
  716. #if HAS_DUAL_Y_STEPPERS
  717. //#define INVERT_Y2_VS_Y_DIR // Y2 direction signal is the opposite of Y
  718. //#define Y_DUAL_ENDSTOPS // Y2 has its own endstop
  719. #if ENABLED(Y_DUAL_ENDSTOPS)
  720. #define Y2_USE_ENDSTOP _YMAX_ // Y2 endstop board plug. Don't forget to enable USE_*_PLUG.
  721. #define Y2_ENDSTOP_ADJUSTMENT 0 // Y2 offset relative to Y endstop
  722. #endif
  723. #endif
  724. //
  725. // Multi-Z steppers
  726. //
  727. #ifdef Z2_DRIVER_TYPE
  728. //#define INVERT_Z2_VS_Z_DIR // Z2 direction signal is the opposite of Z
  729. //#define Z_MULTI_ENDSTOPS // Other Z axes have their own endstops
  730. #if ENABLED(Z_MULTI_ENDSTOPS)
  731. #define Z2_USE_ENDSTOP _XMAX_ // Z2 endstop board plug. Don't forget to enable USE_*_PLUG.
  732. #define Z2_ENDSTOP_ADJUSTMENT 0 // Z2 offset relative to Y endstop
  733. #endif
  734. #ifdef Z3_DRIVER_TYPE
  735. //#define INVERT_Z3_VS_Z_DIR // Z3 direction signal is the opposite of Z
  736. #if ENABLED(Z_MULTI_ENDSTOPS)
  737. #define Z3_USE_ENDSTOP _YMAX_ // Z3 endstop board plug. Don't forget to enable USE_*_PLUG.
  738. #define Z3_ENDSTOP_ADJUSTMENT 0 // Z3 offset relative to Y endstop
  739. #endif
  740. #endif
  741. #ifdef Z4_DRIVER_TYPE
  742. //#define INVERT_Z4_VS_Z_DIR // Z4 direction signal is the opposite of Z
  743. #if ENABLED(Z_MULTI_ENDSTOPS)
  744. #define Z4_USE_ENDSTOP _ZMAX_ // Z4 endstop board plug. Don't forget to enable USE_*_PLUG.
  745. #define Z4_ENDSTOP_ADJUSTMENT 0 // Z4 offset relative to Y endstop
  746. #endif
  747. #endif
  748. #endif
  749. // Drive the E axis with two synchronized steppers
  750. //#define E_DUAL_STEPPER_DRIVERS
  751. #if ENABLED(E_DUAL_STEPPER_DRIVERS)
  752. //#define INVERT_E1_VS_E0_DIR // E direction signals are opposites
  753. #endif
  754. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  755. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  756. //#define EXT_SOLENOID
  757. // @section homing
  758. /**
  759. * Homing Procedure
  760. * Homing (G28) does an indefinite move towards the endstops to establish
  761. * the position of the toolhead relative to the workspace.
  762. */
  763. //#define SENSORLESS_BACKOFF_MM { 2, 2, 0 } // (linear=mm, rotational=°) Backoff from endstops before sensorless homing
  764. #define HOMING_BUMP_MM { 5, 5, 2 } // (linear=mm, rotational=°) Backoff from endstops after first bump
  765. #define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  766. //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing
  767. //#define QUICK_HOME // If G28 contains XY do a diagonal move first
  768. //#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
  769. //#define HOME_Z_FIRST // Home Z first. Requires a Z-MIN endstop (not a probe).
  770. //#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
  771. // @section bltouch
  772. #if ENABLED(BLTOUCH)
  773. /**
  774. * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
  775. * Do not activate settings that the probe might not understand. Clones might misunderstand
  776. * advanced commands.
  777. *
  778. * Note: If the probe is not deploying, do a "Reset" and "Self-Test" and then check the
  779. * wiring of the BROWN, RED and ORANGE wires.
  780. *
  781. * Note: If the trigger signal of your probe is not being recognized, it has been very often
  782. * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
  783. * like they would be with a real switch. So please check the wiring first.
  784. *
  785. * Settings for all BLTouch and clone probes:
  786. */
  787. // Safety: The probe needs time to recognize the command.
  788. // Minimum command delay (ms). Enable and increase if needed.
  789. //#define BLTOUCH_DELAY 500
  790. /**
  791. * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
  792. */
  793. // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
  794. // in special cases, like noisy or filtered input configurations.
  795. //#define BLTOUCH_FORCE_SW_MODE
  796. /**
  797. * Settings for BLTouch Smart 3.0 and 3.1
  798. * Summary:
  799. * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
  800. * - High-Speed mode
  801. * - Disable LCD voltage options
  802. */
  803. /**
  804. * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
  805. * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
  806. * If disabled, OD mode is the hard-coded default on 3.0
  807. * On startup, Marlin will compare its eeprom to this value. If the selected mode
  808. * differs, a mode set eeprom write will be completed at initialization.
  809. * Use the option below to force an eeprom write to a V3.1 probe regardless.
  810. */
  811. //#define BLTOUCH_SET_5V_MODE
  812. /**
  813. * Safety: Activate if connecting a probe with an unknown voltage mode.
  814. * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
  815. * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
  816. * To preserve the life of the probe, use this once then turn it off and re-flash.
  817. */
  818. //#define BLTOUCH_FORCE_MODE_SET
  819. /**
  820. * Enable "HIGH SPEED" option for probing.
  821. * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
  822. * This feature was designed for Deltabots with very fast Z moves; however, higher speed Cartesians
  823. * might be able to use it. If the machine can't raise Z fast enough the BLTouch may go into ALARM.
  824. *
  825. * Set the default state here, change with 'M401 S' or UI, use M500 to save, M502 to reset.
  826. */
  827. //#define BLTOUCH_HS_MODE true
  828. // Safety: Enable voltage mode settings in the LCD menu.
  829. //#define BLTOUCH_LCD_VOLTAGE_MENU
  830. #endif // BLTOUCH
  831. // @section extras
  832. /**
  833. * Z Steppers Auto-Alignment
  834. * Add the G34 command to align multiple Z steppers using a bed probe.
  835. */
  836. //#define Z_STEPPER_AUTO_ALIGN
  837. #if ENABLED(Z_STEPPER_AUTO_ALIGN)
  838. // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
  839. // If not defined, probe limits will be used.
  840. // Override with 'M422 S<index> X<pos> Y<pos>'
  841. //#define Z_STEPPER_ALIGN_XY { { 10, 190 }, { 100, 10 }, { 190, 190 } }
  842. /**
  843. * Orientation for the automatically-calculated probe positions.
  844. * Override Z stepper align points with 'M422 S<index> X<pos> Y<pos>'
  845. *
  846. * 2 Steppers: (0) (1)
  847. * | | 2 |
  848. * | 1 2 | |
  849. * | | 1 |
  850. *
  851. * 3 Steppers: (0) (1) (2) (3)
  852. * | 3 | 1 | 2 1 | 2 |
  853. * | | 3 | | 3 |
  854. * | 1 2 | 2 | 3 | 1 |
  855. *
  856. * 4 Steppers: (0) (1) (2) (3)
  857. * | 4 3 | 1 4 | 2 1 | 3 2 |
  858. * | | | | |
  859. * | 1 2 | 2 3 | 3 4 | 4 1 |
  860. */
  861. #ifndef Z_STEPPER_ALIGN_XY
  862. //#define Z_STEPPERS_ORIENTATION 0
  863. #endif
  864. /**
  865. * Z Stepper positions for more rapid convergence in bed alignment.
  866. * Requires 3 or 4 Z steppers.
  867. *
  868. * Define Stepper XY positions for Z1, Z2, Z3... corresponding to the screw
  869. * positions in the bed carriage, with one position per Z stepper in stepper
  870. * driver order.
  871. */
  872. //#define Z_STEPPER_ALIGN_STEPPER_XY { { 210.7, 102.5 }, { 152.6, 220.0 }, { 94.5, 102.5 } }
  873. #ifndef Z_STEPPER_ALIGN_STEPPER_XY
  874. // Amplification factor. Used to scale the correction step up or down in case
  875. // the stepper (spindle) position is farther out than the test point.
  876. #define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
  877. #endif
  878. // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
  879. #define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
  880. #define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
  881. #define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
  882. #define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
  883. // After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
  884. // Re-homing might be more precise in reproducing the actual 'G28 Z' homing height, especially on an uneven bed.
  885. #define HOME_AFTER_G34
  886. #endif
  887. //
  888. // Add the G35 command to read bed corners to help adjust screws. Requires a bed probe.
  889. //
  890. //#define ASSISTED_TRAMMING
  891. #if ENABLED(ASSISTED_TRAMMING)
  892. // Define positions for probe points.
  893. #define TRAMMING_POINT_XY { { 20, 20 }, { 180, 20 }, { 180, 180 }, { 20, 180 } }
  894. // Define position names for probe points.
  895. #define TRAMMING_POINT_NAME_1 "Front-Left"
  896. #define TRAMMING_POINT_NAME_2 "Front-Right"
  897. #define TRAMMING_POINT_NAME_3 "Back-Right"
  898. #define TRAMMING_POINT_NAME_4 "Back-Left"
  899. #define RESTORE_LEVELING_AFTER_G35 // Enable to restore leveling setup after operation
  900. //#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first
  901. //#define ASSISTED_TRAMMING_WIZARD // Add a Tramming Wizard to the LCD menu
  902. //#define ASSISTED_TRAMMING_WAIT_POSITION { X_CENTER, Y_CENTER, 30 } // Move the nozzle out of the way for adjustment
  903. /**
  904. * Screw thread:
  905. * M3: 30 = Clockwise, 31 = Counter-Clockwise
  906. * M4: 40 = Clockwise, 41 = Counter-Clockwise
  907. * M5: 50 = Clockwise, 51 = Counter-Clockwise
  908. */
  909. #define TRAMMING_SCREW_THREAD 30
  910. #endif
  911. // @section motion
  912. #define AXIS_RELATIVE_MODES { false, false, false, false }
  913. // Add a Duplicate option for well-separated conjoined nozzles
  914. //#define MULTI_NOZZLE_DUPLICATION
  915. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  916. #define INVERT_X_STEP_PIN false
  917. #define INVERT_Y_STEP_PIN false
  918. #define INVERT_Z_STEP_PIN false
  919. #define INVERT_I_STEP_PIN false
  920. #define INVERT_J_STEP_PIN false
  921. #define INVERT_K_STEP_PIN false
  922. #define INVERT_U_STEP_PIN false
  923. #define INVERT_V_STEP_PIN false
  924. #define INVERT_W_STEP_PIN false
  925. #define INVERT_E_STEP_PIN false
  926. /**
  927. * Idle Stepper Shutdown
  928. * Set DISABLE_INACTIVE_? 'true' to shut down axis steppers after an idle period.
  929. * The Deactive Time can be overridden with M18 and M84. Set to 0 for No Timeout.
  930. */
  931. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  932. #define DISABLE_INACTIVE_X true
  933. #define DISABLE_INACTIVE_Y true
  934. #define DISABLE_INACTIVE_Z true // Set 'false' if the nozzle could fall onto your printed part!
  935. #define DISABLE_INACTIVE_I true
  936. #define DISABLE_INACTIVE_J true
  937. #define DISABLE_INACTIVE_K true
  938. #define DISABLE_INACTIVE_U true
  939. #define DISABLE_INACTIVE_V true
  940. #define DISABLE_INACTIVE_W true
  941. #define DISABLE_INACTIVE_E true
  942. // Default Minimum Feedrates for printing and travel moves
  943. #define DEFAULT_MINIMUMFEEDRATE 0.0 // (mm/s. °/s for rotational-only moves) Minimum feedrate. Set with M205 S.
  944. #define DEFAULT_MINTRAVELFEEDRATE 0.0 // (mm/s. °/s for rotational-only moves) Minimum travel feedrate. Set with M205 T.
  945. // Minimum time that a segment needs to take as the buffer gets emptied
  946. #define DEFAULT_MINSEGMENTTIME 20000 // (µs) Set with M205 B.
  947. // Slow down the machine if the lookahead buffer is (by default) half full.
  948. // Increase the slowdown divisor for larger buffer sizes.
  949. #define SLOWDOWN
  950. #if ENABLED(SLOWDOWN)
  951. #define SLOWDOWN_DIVISOR 2
  952. #endif
  953. /**
  954. * XY Frequency limit
  955. * Reduce resonance by limiting the frequency of small zigzag infill moves.
  956. * See https://hydraraptor.blogspot.com/2010/12/frequency-limit.html
  957. * Use M201 F<freq> G<min%> to change limits at runtime.
  958. */
  959. //#define XY_FREQUENCY_LIMIT 10 // (Hz) Maximum frequency of small zigzag infill moves. Set with M201 F<hertz>.
  960. #ifdef XY_FREQUENCY_LIMIT
  961. #define XY_FREQUENCY_MIN_PERCENT 5 // (percent) Minimum FR percentage to apply. Set with M201 G<min%>.
  962. #endif
  963. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  964. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  965. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  966. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
  967. //
  968. // Backlash Compensation
  969. // Adds extra movement to axes on direction-changes to account for backlash.
  970. //
  971. //#define BACKLASH_COMPENSATION
  972. #if ENABLED(BACKLASH_COMPENSATION)
  973. // Define values for backlash distance and correction.
  974. // If BACKLASH_GCODE is enabled these values are the defaults.
  975. #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (linear=mm, rotational=°) One value for each linear axis
  976. #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction
  977. // Add steps for motor direction changes on CORE kinematics
  978. //#define CORE_BACKLASH
  979. // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments
  980. // to reduce print artifacts. (Enabling this is costly in memory and computation!)
  981. //#define BACKLASH_SMOOTHING_MM 3 // (mm)
  982. // Add runtime configuration and tuning of backlash values (M425)
  983. //#define BACKLASH_GCODE
  984. #if ENABLED(BACKLASH_GCODE)
  985. // Measure the Z backlash when probing (G29) and set with "M425 Z"
  986. #define MEASURE_BACKLASH_WHEN_PROBING
  987. #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
  988. // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT
  989. // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION
  990. // increments while checking for the contact to be broken.
  991. #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm)
  992. #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm)
  993. #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_FEEDRATE_SLOW // (mm/min)
  994. #endif
  995. #endif
  996. #endif
  997. /**
  998. * Automatic backlash, position and hotend offset calibration
  999. *
  1000. * Enable G425 to run automatic calibration using an electrically-
  1001. * conductive cube, bolt, or washer mounted on the bed.
  1002. *
  1003. * G425 uses the probe to touch the top and sides of the calibration object
  1004. * on the bed and measures and/or correct positional offsets, axis backlash
  1005. * and hotend offsets.
  1006. *
  1007. * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within
  1008. * ±5mm of true values for G425 to succeed.
  1009. */
  1010. //#define CALIBRATION_GCODE
  1011. #if ENABLED(CALIBRATION_GCODE)
  1012. //#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
  1013. //#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
  1014. #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm
  1015. #define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
  1016. #define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
  1017. #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
  1018. // The following parameters refer to the conical section of the nozzle tip.
  1019. #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
  1020. #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
  1021. // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM).
  1022. //#define CALIBRATION_REPORTING
  1023. // The true location and dimension the cube/bolt/washer on the bed.
  1024. #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
  1025. #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
  1026. // Comment out any sides which are unreachable by the probe. For best
  1027. // auto-calibration results, all sides must be reachable.
  1028. #define CALIBRATION_MEASURE_RIGHT
  1029. #define CALIBRATION_MEASURE_FRONT
  1030. #define CALIBRATION_MEASURE_LEFT
  1031. #define CALIBRATION_MEASURE_BACK
  1032. //#define CALIBRATION_MEASURE_IMIN
  1033. //#define CALIBRATION_MEASURE_IMAX
  1034. //#define CALIBRATION_MEASURE_JMIN
  1035. //#define CALIBRATION_MEASURE_JMAX
  1036. //#define CALIBRATION_MEASURE_KMIN
  1037. //#define CALIBRATION_MEASURE_KMAX
  1038. //#define CALIBRATION_MEASURE_UMIN
  1039. //#define CALIBRATION_MEASURE_UMAX
  1040. //#define CALIBRATION_MEASURE_VMIN
  1041. //#define CALIBRATION_MEASURE_VMAX
  1042. //#define CALIBRATION_MEASURE_WMIN
  1043. //#define CALIBRATION_MEASURE_WMAX
  1044. // Probing at the exact top center only works if the center is flat. If
  1045. // probing on a screwhead or hollow washer, probe near the edges.
  1046. //#define CALIBRATION_MEASURE_AT_TOP_EDGES
  1047. // Define the pin to read during calibration
  1048. #ifndef CALIBRATION_PIN
  1049. //#define CALIBRATION_PIN -1 // Define here to override the default pin
  1050. #define CALIBRATION_PIN_INVERTING false // Set to true to invert the custom pin
  1051. //#define CALIBRATION_PIN_PULLDOWN
  1052. #define CALIBRATION_PIN_PULLUP
  1053. #endif
  1054. #endif
  1055. /**
  1056. * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
  1057. * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
  1058. * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  1059. * lowest stepping frequencies.
  1060. */
  1061. //#define ADAPTIVE_STEP_SMOOTHING
  1062. /**
  1063. * Custom Microstepping
  1064. * Override as-needed for your setup. Up to 3 MS pins are supported.
  1065. */
  1066. //#define MICROSTEP1 LOW,LOW,LOW
  1067. //#define MICROSTEP2 HIGH,LOW,LOW
  1068. //#define MICROSTEP4 LOW,HIGH,LOW
  1069. //#define MICROSTEP8 HIGH,HIGH,LOW
  1070. //#define MICROSTEP16 LOW,LOW,HIGH
  1071. //#define MICROSTEP32 HIGH,LOW,HIGH
  1072. // Microstep settings (Requires a board with pins named X_MS1, X_MS2, etc.)
  1073. #define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
  1074. /**
  1075. * @section stepper motor current
  1076. *
  1077. * Some boards have a means of setting the stepper motor current via firmware.
  1078. *
  1079. * The power on motor currents are set by:
  1080. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  1081. * known compatible chips: A4982
  1082. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  1083. * known compatible chips: AD5206
  1084. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  1085. * known compatible chips: MCP4728
  1086. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE
  1087. * known compatible chips: MCP4451, MCP4018
  1088. *
  1089. * Motor currents can also be set by M907 - M910 and by the LCD.
  1090. * M907 - applies to all.
  1091. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  1092. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  1093. */
  1094. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  1095. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  1096. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  1097. /**
  1098. * I2C-based DIGIPOTs (e.g., Azteeg X3 Pro)
  1099. */
  1100. //#define DIGIPOT_MCP4018 // Requires https://github.com/felias-fogg/SlowSoftI2CMaster
  1101. //#define DIGIPOT_MCP4451
  1102. #if EITHER(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
  1103. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT:4 AZTEEG_X3_PRO:8 MKS_SBASE:5 MIGHTYBOARD_REVE:5
  1104. // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
  1105. // These correspond to the physical drivers, so be mindful if the order is changed.
  1106. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  1107. //#define DIGIPOT_USE_RAW_VALUES // Use DIGIPOT_MOTOR_CURRENT raw wiper values (instead of A4988 motor currents)
  1108. /**
  1109. * Common slave addresses:
  1110. *
  1111. * A (A shifted) B (B shifted) IC
  1112. * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
  1113. * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
  1114. * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451
  1115. * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451
  1116. * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018
  1117. */
  1118. //#define DIGIPOT_I2C_ADDRESS_A 0x2C // Unshifted slave address for first DIGIPOT
  1119. //#define DIGIPOT_I2C_ADDRESS_B 0x2D // Unshifted slave address for second DIGIPOT
  1120. #endif
  1121. //===========================================================================
  1122. //=============================Additional Features===========================
  1123. //===========================================================================
  1124. // @section lcd
  1125. #if HAS_MANUAL_MOVE_MENU
  1126. #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // (mm/min) Feedrates for manual moves along X, Y, Z, E from panel
  1127. #define FINE_MANUAL_MOVE 0.025 // (mm) Smallest manual move (< 0.1mm) applying to Z on most machines
  1128. #if IS_ULTIPANEL
  1129. #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
  1130. #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen
  1131. #endif
  1132. #endif
  1133. // Change values more rapidly when the encoder is rotated faster
  1134. #define ENCODER_RATE_MULTIPLIER
  1135. #if ENABLED(ENCODER_RATE_MULTIPLIER)
  1136. #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed
  1137. #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed
  1138. #endif
  1139. // Play a beep when the feedrate is changed from the Status Screen
  1140. //#define BEEP_ON_FEEDRATE_CHANGE
  1141. #if ENABLED(BEEP_ON_FEEDRATE_CHANGE)
  1142. #define FEEDRATE_CHANGE_BEEP_DURATION 10
  1143. #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
  1144. #endif
  1145. //
  1146. // LCD Backlight Timeout
  1147. //
  1148. //#define LCD_BACKLIGHT_TIMEOUT 30 // (s) Timeout before turning off the backlight
  1149. #if HAS_BED_PROBE && EITHER(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
  1150. //#define PROBE_OFFSET_WIZARD // Add a Probe Z Offset calibration option to the LCD menu
  1151. #if ENABLED(PROBE_OFFSET_WIZARD)
  1152. /**
  1153. * Enable to init the Probe Z-Offset when starting the Wizard.
  1154. * Use a height slightly above the estimated nozzle-to-probe Z offset.
  1155. * For example, with an offset of -5, consider a starting height of -4.
  1156. */
  1157. //#define PROBE_OFFSET_WIZARD_START_Z -4.0
  1158. // Set a convenient position to do the calibration (probing point and nozzle/bed-distance)
  1159. //#define PROBE_OFFSET_WIZARD_XY_POS { X_CENTER, Y_CENTER }
  1160. #endif
  1161. #endif
  1162. #if HAS_MARLINUI_MENU
  1163. #if HAS_BED_PROBE
  1164. // Add calibration in the Probe Offsets menu to compensate for X-axis twist.
  1165. //#define X_AXIS_TWIST_COMPENSATION
  1166. #if ENABLED(X_AXIS_TWIST_COMPENSATION)
  1167. /**
  1168. * Enable to init the Probe Z-Offset when starting the Wizard.
  1169. * Use a height slightly above the estimated nozzle-to-probe Z offset.
  1170. * For example, with an offset of -5, consider a starting height of -4.
  1171. */
  1172. #define XATC_START_Z 0.0
  1173. #define XATC_MAX_POINTS 3 // Number of points to probe in the wizard
  1174. #define XATC_Y_POSITION Y_CENTER // (mm) Y position to probe
  1175. #define XATC_Z_OFFSETS { 0, 0, 0 } // Z offsets for X axis sample points
  1176. #endif
  1177. // Show Deploy / Stow Probe options in the Motion menu.
  1178. #define PROBE_DEPLOY_STOW_MENU
  1179. #endif
  1180. // Include a page of printer information in the LCD Main Menu
  1181. //#define LCD_INFO_MENU
  1182. #if ENABLED(LCD_INFO_MENU)
  1183. //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
  1184. #endif
  1185. // BACK menu items keep the highlight at the top
  1186. //#define TURBO_BACK_MENU_ITEM
  1187. // Insert a menu for preheating at the top level to allow for quick access
  1188. //#define PREHEAT_SHORTCUT_MENU_ITEM
  1189. #endif // HAS_MARLINUI_MENU
  1190. #if EITHER(HAS_DISPLAY, DWIN_LCD_PROUI)
  1191. //#define SOUND_MENU_ITEM // Add a mute option to the LCD menu
  1192. #define SOUND_ON_DEFAULT // Buzzer/speaker default enabled state
  1193. #endif
  1194. #if EITHER(HAS_DISPLAY, DWIN_LCD_PROUI)
  1195. // The timeout to return to the status screen from sub-menus
  1196. //#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
  1197. #if ENABLED(SHOW_BOOTSCREEN)
  1198. #define BOOTSCREEN_TIMEOUT 4000 // (ms) Total Duration to display the boot screen(s)
  1199. #if EITHER(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
  1200. #define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
  1201. #endif
  1202. #endif
  1203. // Scroll a longer status message into view
  1204. //#define STATUS_MESSAGE_SCROLLING
  1205. // Apply a timeout to low-priority status messages
  1206. //#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
  1207. // On the Info Screen, display XY with one decimal place when possible
  1208. //#define LCD_DECIMAL_SMALL_XY
  1209. // Add an 'M73' G-code to set the current percentage
  1210. //#define LCD_SET_PROGRESS_MANUALLY
  1211. // Show the E position (filament used) during printing
  1212. //#define LCD_SHOW_E_TOTAL
  1213. /**
  1214. * LED Control Menu
  1215. * Add LED Control to the LCD menu
  1216. */
  1217. //#define LED_CONTROL_MENU
  1218. #if ENABLED(LED_CONTROL_MENU)
  1219. #define LED_COLOR_PRESETS // Enable the Preset Color menu option
  1220. //#define NEO2_COLOR_PRESETS // Enable a second NeoPixel Preset Color menu option
  1221. #if ENABLED(LED_COLOR_PRESETS)
  1222. #define LED_USER_PRESET_RED 255 // User defined RED value
  1223. #define LED_USER_PRESET_GREEN 128 // User defined GREEN value
  1224. #define LED_USER_PRESET_BLUE 0 // User defined BLUE value
  1225. #define LED_USER_PRESET_WHITE 255 // User defined WHITE value
  1226. #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  1227. //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
  1228. #endif
  1229. #if ENABLED(NEO2_COLOR_PRESETS)
  1230. #define NEO2_USER_PRESET_RED 255 // User defined RED value
  1231. #define NEO2_USER_PRESET_GREEN 128 // User defined GREEN value
  1232. #define NEO2_USER_PRESET_BLUE 0 // User defined BLUE value
  1233. #define NEO2_USER_PRESET_WHITE 255 // User defined WHITE value
  1234. #define NEO2_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  1235. //#define NEO2_USER_PRESET_STARTUP // Have the printer display the user preset color on startup for the second strip
  1236. #endif
  1237. #endif
  1238. #endif
  1239. // LCD Print Progress options
  1240. #if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
  1241. #if CAN_SHOW_REMAINING_TIME
  1242. //#define SHOW_REMAINING_TIME // Display estimated time to completion
  1243. #if ENABLED(SHOW_REMAINING_TIME)
  1244. //#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
  1245. //#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
  1246. #endif
  1247. #endif
  1248. #if EITHER(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI)
  1249. //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
  1250. #endif
  1251. #if EITHER(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
  1252. //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
  1253. #if ENABLED(LCD_PROGRESS_BAR)
  1254. #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
  1255. #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
  1256. #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
  1257. //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
  1258. //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
  1259. #endif
  1260. #endif
  1261. #endif
  1262. #if ENABLED(SDSUPPORT)
  1263. /**
  1264. * SD Card SPI Speed
  1265. * May be required to resolve "volume init" errors.
  1266. *
  1267. * Enable and set to SPI_HALF_SPEED, SPI_QUARTER_SPEED, or SPI_EIGHTH_SPEED
  1268. * otherwise full speed will be applied.
  1269. *
  1270. * :['SPI_HALF_SPEED', 'SPI_QUARTER_SPEED', 'SPI_EIGHTH_SPEED']
  1271. */
  1272. //#define SD_SPI_SPEED SPI_HALF_SPEED
  1273. // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
  1274. // Enable this option and set to HIGH if your SD cards are incorrectly detected.
  1275. //#define SD_DETECT_STATE HIGH
  1276. //#define SD_IGNORE_AT_STARTUP // Don't mount the SD card when starting up
  1277. //#define SDCARD_READONLY // Read-only SD card (to save over 2K of flash)
  1278. //#define GCODE_REPEAT_MARKERS // Enable G-code M808 to set repeat markers and do looping
  1279. #define SD_PROCEDURE_DEPTH 1 // Increase if you need more nested M32 calls
  1280. #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
  1281. #define SD_FINISHED_RELEASECOMMAND "M84" // Use "M84XYE" to keep Z enabled so your bed stays in place
  1282. // Reverse SD sort to show "more recent" files first, according to the card's FAT.
  1283. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
  1284. #define SDCARD_RATHERRECENTFIRST
  1285. #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing
  1286. //#define NO_SD_AUTOSTART // Remove auto#.g file support completely to save some Flash, SRAM
  1287. //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
  1288. //#define BROWSE_MEDIA_ON_INSERT // Open the file browser when media is inserted
  1289. //#define MEDIA_MENU_AT_TOP // Force the media menu to be listed on the top of the main menu
  1290. #define EVENT_GCODE_SD_ABORT "G28XY" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
  1291. #if ENABLED(PRINTER_EVENT_LEDS)
  1292. #define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
  1293. #endif
  1294. /**
  1295. * Continue after Power-Loss (Creality3D)
  1296. *
  1297. * Store the current state to the SD Card at the start of each layer
  1298. * during SD printing. If the recovery file is found at boot time, present
  1299. * an option on the LCD screen to continue the print from the last-known
  1300. * point in the file.
  1301. */
  1302. //#define POWER_LOSS_RECOVERY
  1303. #if ENABLED(POWER_LOSS_RECOVERY)
  1304. #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
  1305. //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
  1306. //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
  1307. //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
  1308. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
  1309. //#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor
  1310. //#define POWER_LOSS_PULLDOWN
  1311. //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
  1312. //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
  1313. // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
  1314. // especially with "vase mode" printing. Set too high and vases cannot be continued.
  1315. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
  1316. // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
  1317. //#define POWER_LOSS_RECOVER_ZHOME
  1318. #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
  1319. //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
  1320. #endif
  1321. #endif
  1322. /**
  1323. * Sort SD file listings in alphabetical order.
  1324. *
  1325. * With this option enabled, items on SD cards will be sorted
  1326. * by name for easier navigation.
  1327. *
  1328. * By default...
  1329. *
  1330. * - Use the slowest -but safest- method for sorting.
  1331. * - Folders are sorted to the top.
  1332. * - The sort key is statically allocated.
  1333. * - No added G-code (M34) support.
  1334. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  1335. *
  1336. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  1337. * compiler to calculate the worst-case usage and throw an error if the SRAM
  1338. * limit is exceeded.
  1339. *
  1340. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  1341. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  1342. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  1343. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  1344. */
  1345. //#define SDCARD_SORT_ALPHA
  1346. // SD Card Sorting options
  1347. #if ENABLED(SDCARD_SORT_ALPHA)
  1348. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
  1349. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  1350. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 G-code.
  1351. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
  1352. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  1353. #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  1354. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  1355. #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
  1356. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
  1357. #endif
  1358. // Allow international symbols in long filenames. To display correctly, the
  1359. // LCD's font must contain the characters. Check your selected LCD language.
  1360. //#define UTF_FILENAME_SUPPORT
  1361. //#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
  1362. //#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
  1363. //#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
  1364. //#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!)
  1365. /**
  1366. * Abort SD printing when any endstop is triggered.
  1367. * This feature is enabled with 'M540 S1' or from the LCD menu.
  1368. * Endstops must be activated for this option to work.
  1369. */
  1370. //#define SD_ABORT_ON_ENDSTOP_HIT
  1371. //#define SD_REPRINT_LAST_SELECTED_FILE // On print completion open the LCD Menu and select the same file
  1372. //#define AUTO_REPORT_SD_STATUS // Auto-report media status with 'M27 S<seconds>'
  1373. /**
  1374. * Support for USB thumb drives using an Arduino USB Host Shield or
  1375. * equivalent MAX3421E breakout board. The USB thumb drive will appear
  1376. * to Marlin as an SD card.
  1377. *
  1378. * The MAX3421E can be assigned the same pins as the SD card reader, with
  1379. * the following pin mapping:
  1380. *
  1381. * SCLK, MOSI, MISO --> SCLK, MOSI, MISO
  1382. * INT --> SD_DETECT_PIN [1]
  1383. * SS --> SDSS
  1384. *
  1385. * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility.
  1386. */
  1387. //#define USB_FLASH_DRIVE_SUPPORT
  1388. #if ENABLED(USB_FLASH_DRIVE_SUPPORT)
  1389. /**
  1390. * USB Host Shield Library
  1391. *
  1392. * - UHS2 uses no interrupts and has been production-tested
  1393. * on a LulzBot TAZ Pro with a 32-bit Archim board.
  1394. *
  1395. * - UHS3 is newer code with better USB compatibility. But it
  1396. * is less tested and is known to interfere with Servos.
  1397. * [1] This requires USB_INTR_PIN to be interrupt-capable.
  1398. */
  1399. //#define USE_UHS2_USB
  1400. //#define USE_UHS3_USB
  1401. /**
  1402. * Native USB Host supported by some boards (USB OTG)
  1403. */
  1404. //#define USE_OTG_USB_HOST
  1405. #if DISABLED(USE_OTG_USB_HOST)
  1406. #define USB_CS_PIN SDSS
  1407. #define USB_INTR_PIN SD_DETECT_PIN
  1408. #endif
  1409. #endif
  1410. /**
  1411. * When using a bootloader that supports SD-Firmware-Flashing,
  1412. * add a menu item to activate SD-FW-Update on the next reboot.
  1413. *
  1414. * Requires ATMEGA2560 (Arduino Mega)
  1415. *
  1416. * Tested with this bootloader:
  1417. * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560
  1418. */
  1419. //#define SD_FIRMWARE_UPDATE
  1420. #if ENABLED(SD_FIRMWARE_UPDATE)
  1421. #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF
  1422. #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0
  1423. #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF
  1424. #endif
  1425. /**
  1426. * Enable this option if you have more than ~3K of unused flash space.
  1427. * Marlin will embed all settings in the firmware binary as compressed data.
  1428. * Use 'M503 C' to write the settings out to the SD Card as 'mc.zip'.
  1429. * See docs/ConfigEmbedding.md for details on how to use 'mc-apply.py'.
  1430. */
  1431. //#define CONFIGURATION_EMBEDDING
  1432. // Add an optimized binary file transfer mode, initiated with 'M28 B1'
  1433. //#define BINARY_FILE_TRANSFER
  1434. #if ENABLED(BINARY_FILE_TRANSFER)
  1435. // Include extra facilities (e.g., 'M20 F') supporting firmware upload via BINARY_FILE_TRANSFER
  1436. //#define CUSTOM_FIRMWARE_UPLOAD
  1437. #endif
  1438. /**
  1439. * Set this option to one of the following (or the board's defaults apply):
  1440. *
  1441. * LCD - Use the SD drive in the external LCD controller.
  1442. * ONBOARD - Use the SD drive on the control board.
  1443. * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
  1444. *
  1445. * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
  1446. */
  1447. //#define SDCARD_CONNECTION LCD
  1448. // Enable if SD detect is rendered useless (e.g., by using an SD extender)
  1449. //#define NO_SD_DETECT
  1450. /**
  1451. * Multiple volume support - EXPERIMENTAL.
  1452. * Adds 'M21 Pm' / 'M21 S' / 'M21 U' to mount SD Card / USB Drive.
  1453. */
  1454. //#define MULTI_VOLUME
  1455. #if ENABLED(MULTI_VOLUME)
  1456. #define VOLUME_SD_ONBOARD
  1457. #define VOLUME_USB_FLASH_DRIVE
  1458. #define DEFAULT_VOLUME SV_SD_ONBOARD
  1459. #define DEFAULT_SHARED_VOLUME SV_USB_FLASH_DRIVE
  1460. #endif
  1461. #endif // SDSUPPORT
  1462. /**
  1463. * By default an onboard SD card reader may be shared as a USB mass-
  1464. * storage device. This option hides the SD card from the host PC.
  1465. */
  1466. //#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security).
  1467. /**
  1468. * Additional options for Graphical Displays
  1469. *
  1470. * Use the optimizations here to improve printing performance,
  1471. * which can be adversely affected by graphical display drawing,
  1472. * especially when doing several short moves, and when printing
  1473. * on DELTA and SCARA machines.
  1474. *
  1475. * Some of these options may result in the display lagging behind
  1476. * controller events, as there is a trade-off between reliable
  1477. * printing performance versus fast display updates.
  1478. */
  1479. #if HAS_MARLINUI_U8GLIB
  1480. // Save many cycles by drawing a hollow frame or no frame on the Info Screen
  1481. //#define XYZ_NO_FRAME
  1482. #define XYZ_HOLLOW_FRAME
  1483. // A bigger font is available for edit items. Costs 3120 bytes of flash.
  1484. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1485. //#define USE_BIG_EDIT_FONT
  1486. // A smaller font may be used on the Info Screen. Costs 2434 bytes of flash.
  1487. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1488. //#define USE_SMALL_INFOFONT
  1489. /**
  1490. * Graphical Display Sleep
  1491. *
  1492. * The U8G library provides sleep / wake functions for SH1106, SSD1306,
  1493. * SSD1309, and some other DOGM displays.
  1494. * Enable this option to save energy and prevent OLED pixel burn-in.
  1495. * Adds the menu item Configuration > LCD Timeout (m) to set a wait period
  1496. * from 0 (disabled) to 99 minutes.
  1497. */
  1498. //#define DISPLAY_SLEEP_MINUTES 2 // (minutes) Timeout before turning off the screen
  1499. /**
  1500. * ST7920-based LCDs can emulate a 16 x 4 character display using
  1501. * the ST7920 character-generator for very fast screen updates.
  1502. * Enable LIGHTWEIGHT_UI to use this special display mode.
  1503. *
  1504. * Since LIGHTWEIGHT_UI has limited space, the position and status
  1505. * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
  1506. * length of time to display the status message before clearing.
  1507. *
  1508. * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
  1509. * This will prevent position updates from being displayed.
  1510. */
  1511. #if IS_U8GLIB_ST7920
  1512. // Enable this option and reduce the value to optimize screen updates.
  1513. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  1514. //#define DOGM_SPI_DELAY_US 5
  1515. //#define LIGHTWEIGHT_UI
  1516. #if ENABLED(LIGHTWEIGHT_UI)
  1517. #define STATUS_EXPIRE_SECONDS 20
  1518. #endif
  1519. #endif
  1520. /**
  1521. * Status (Info) Screen customizations
  1522. * These options may affect code size and screen render time.
  1523. * Custom status screens can forcibly override these settings.
  1524. */
  1525. //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones
  1526. //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends)
  1527. #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM for numbered hotends)
  1528. #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating
  1529. #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating
  1530. #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating
  1531. //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active
  1532. //#define STATUS_COOLER_ANIM // Use a second bitmap to indicate laser cooling
  1533. //#define STATUS_FLOWMETER_ANIM // Use multiple bitmaps to indicate coolant flow
  1534. //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
  1535. //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
  1536. //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
  1537. //#define STATUS_HEAT_PERCENT // Show heating in a progress bar
  1538. //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash.
  1539. // Frivolous Game Options
  1540. //#define MARLIN_BRICKOUT
  1541. //#define MARLIN_INVADERS
  1542. //#define MARLIN_SNAKE
  1543. //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu
  1544. #endif // HAS_MARLINUI_U8GLIB
  1545. #if HAS_MARLINUI_U8GLIB || IS_DWIN_MARLINUI
  1546. // Show SD percentage next to the progress bar
  1547. //#define SHOW_SD_PERCENT
  1548. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  1549. #define MENU_HOLLOW_FRAME
  1550. // Swap the CW/CCW indicators in the graphics overlay
  1551. //#define OVERLAY_GFX_REVERSE
  1552. #endif
  1553. //
  1554. // Additional options for DGUS / DWIN displays
  1555. //
  1556. #if HAS_DGUS_LCD
  1557. #define LCD_BAUDRATE 115200
  1558. #define DGUS_RX_BUFFER_SIZE 128
  1559. #define DGUS_TX_BUFFER_SIZE 48
  1560. //#define SERIAL_STATS_RX_BUFFER_OVERRUNS // Fix Rx overrun situation (Currently only for AVR)
  1561. #define DGUS_UPDATE_INTERVAL_MS 500 // (ms) Interval between automatic screen updates
  1562. #if ANY(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_MKS, DGUS_LCD_UI_HIPRECY)
  1563. #define DGUS_PRINT_FILENAME // Display the filename during printing
  1564. #define DGUS_PREHEAT_UI // Display a preheat screen during heatup
  1565. #if EITHER(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_MKS)
  1566. //#define DGUS_UI_MOVE_DIS_OPTION // Disabled by default for FYSETC and MKS
  1567. #else
  1568. #define DGUS_UI_MOVE_DIS_OPTION // Enabled by default for UI_HIPRECY
  1569. #endif
  1570. #define DGUS_FILAMENT_LOADUNLOAD
  1571. #if ENABLED(DGUS_FILAMENT_LOADUNLOAD)
  1572. #define DGUS_FILAMENT_PURGE_LENGTH 10
  1573. #define DGUS_FILAMENT_LOAD_LENGTH_PER_TIME 0.5 // (mm) Adjust in proportion to DGUS_UPDATE_INTERVAL_MS
  1574. #endif
  1575. #define DGUS_UI_WAITING // Show a "waiting" screen between some screens
  1576. #if ENABLED(DGUS_UI_WAITING)
  1577. #define DGUS_UI_WAITING_STATUS 10
  1578. #define DGUS_UI_WAITING_STATUS_PERIOD 8 // Increase to slower waiting status looping
  1579. #endif
  1580. #endif
  1581. #endif // HAS_DGUS_LCD
  1582. //
  1583. // Additional options for AnyCubic Chiron TFT displays
  1584. //
  1585. #if ENABLED(ANYCUBIC_LCD_CHIRON)
  1586. // By default the type of panel is automatically detected.
  1587. // Enable one of these options if you know the panel type.
  1588. //#define CHIRON_TFT_STANDARD
  1589. //#define CHIRON_TFT_NEW
  1590. // Enable the longer Anycubic powerup startup tune
  1591. //#define AC_DEFAULT_STARTUP_TUNE
  1592. /**
  1593. * Display Folders
  1594. * By default the file browser lists all G-code files (including those in subfolders) in a flat list.
  1595. * Enable this option to display a hierarchical file browser.
  1596. *
  1597. * NOTES:
  1598. * - Without this option it helps to enable SDCARD_SORT_ALPHA so files are sorted before/after folders.
  1599. * - When used with the "new" panel, folder names will also have '.gcode' appended to their names.
  1600. * This hack is currently required to force the panel to show folders.
  1601. */
  1602. #define AC_SD_FOLDER_VIEW
  1603. #endif
  1604. //
  1605. // Specify additional languages for the UI. Default specified by LCD_LANGUAGE.
  1606. //
  1607. #if ANY(DOGLCD, TFT_COLOR_UI, TOUCH_UI_FTDI_EVE, IS_DWIN_MARLINUI)
  1608. //#define LCD_LANGUAGE_2 fr
  1609. //#define LCD_LANGUAGE_3 de
  1610. //#define LCD_LANGUAGE_4 es
  1611. //#define LCD_LANGUAGE_5 it
  1612. #ifdef LCD_LANGUAGE_2
  1613. //#define LCD_LANGUAGE_AUTO_SAVE // Automatically save language to EEPROM on change
  1614. #endif
  1615. #endif
  1616. //
  1617. // Touch UI for the FTDI Embedded Video Engine (EVE)
  1618. //
  1619. #if ENABLED(TOUCH_UI_FTDI_EVE)
  1620. // Display board used
  1621. //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240)
  1622. //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
  1623. //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272)
  1624. //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480)
  1625. //#define LCD_LULZBOT_CLCD_UI // LulzBot Color LCD UI
  1626. //#define LCD_FYSETC_TFT81050 // FYSETC with 5" (800x480)
  1627. //#define LCD_EVE3_50G // Matrix Orbital 5.0", 800x480, BT815
  1628. //#define LCD_EVE2_50G // Matrix Orbital 5.0", 800x480, FT813
  1629. // Correct the resolution if not using the stock TFT panel.
  1630. //#define TOUCH_UI_320x240
  1631. //#define TOUCH_UI_480x272
  1632. //#define TOUCH_UI_800x480
  1633. // Mappings for boards with a standard RepRapDiscount Display connector
  1634. //#define AO_EXP1_PINMAP // LulzBot CLCD UI EXP1 mapping
  1635. //#define AO_EXP2_PINMAP // LulzBot CLCD UI EXP2 mapping
  1636. //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping
  1637. //#define S6_TFT_PINMAP // FYSETC S6 pin mapping
  1638. //#define F6_TFT_PINMAP // FYSETC F6 pin mapping
  1639. //#define OTHER_PIN_LAYOUT // Define pins manually below
  1640. #if ENABLED(OTHER_PIN_LAYOUT)
  1641. // Pins for CS and MOD_RESET (PD) must be chosen
  1642. #define CLCD_MOD_RESET 9
  1643. #define CLCD_SPI_CS 10
  1644. // If using software SPI, specify pins for SCLK, MOSI, MISO
  1645. //#define CLCD_USE_SOFT_SPI
  1646. #if ENABLED(CLCD_USE_SOFT_SPI)
  1647. #define CLCD_SOFT_SPI_MOSI 11
  1648. #define CLCD_SOFT_SPI_MISO 12
  1649. #define CLCD_SOFT_SPI_SCLK 13
  1650. #endif
  1651. #endif
  1652. // Display Orientation. An inverted (i.e. upside-down) display
  1653. // is supported on the FT800. The FT810 and beyond also support
  1654. // portrait and mirrored orientations.
  1655. //#define TOUCH_UI_INVERTED
  1656. //#define TOUCH_UI_PORTRAIT
  1657. //#define TOUCH_UI_MIRRORED
  1658. // UTF8 processing and rendering.
  1659. // Unsupported characters are shown as '?'.
  1660. //#define TOUCH_UI_USE_UTF8
  1661. #if ENABLED(TOUCH_UI_USE_UTF8)
  1662. // Western accents support. These accented characters use
  1663. // combined bitmaps and require relatively little storage.
  1664. #define TOUCH_UI_UTF8_WESTERN_CHARSET
  1665. #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET)
  1666. // Additional character groups. These characters require
  1667. // full bitmaps and take up considerable storage:
  1668. //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³
  1669. //#define TOUCH_UI_UTF8_COPYRIGHT // © ®
  1670. //#define TOUCH_UI_UTF8_GERMANIC // ß
  1671. //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ
  1672. //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡
  1673. //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥
  1674. //#define TOUCH_UI_UTF8_ORDINALS // º ª
  1675. //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷
  1676. //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾
  1677. //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬
  1678. #endif
  1679. // Cyrillic character set, costs about 27KiB of flash
  1680. //#define TOUCH_UI_UTF8_CYRILLIC_CHARSET
  1681. #endif
  1682. // Use a smaller font when labels don't fit buttons
  1683. #define TOUCH_UI_FIT_TEXT
  1684. // Use a numeric passcode for "Screen lock" keypad.
  1685. // (recommended for smaller displays)
  1686. //#define TOUCH_UI_PASSCODE
  1687. // Output extra debug info for Touch UI events
  1688. //#define TOUCH_UI_DEBUG
  1689. // Developer menu (accessed by touching "About Printer" copyright text)
  1690. //#define TOUCH_UI_DEVELOPER_MENU
  1691. #endif
  1692. //
  1693. // Classic UI Options
  1694. //
  1695. #if TFT_SCALED_DOGLCD
  1696. //#define TFT_MARLINUI_COLOR 0xFFFF // White
  1697. //#define TFT_MARLINBG_COLOR 0x0000 // Black
  1698. //#define TFT_DISABLED_COLOR 0x0003 // Almost black
  1699. //#define TFT_BTCANCEL_COLOR 0xF800 // Red
  1700. //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow
  1701. //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan
  1702. #endif
  1703. //
  1704. // ADC Button Debounce
  1705. //
  1706. #if HAS_ADC_BUTTONS
  1707. #define ADC_BUTTON_DEBOUNCE_DELAY 16 // Increase if buttons bounce or repeat too fast
  1708. #endif
  1709. // @section safety
  1710. /**
  1711. * The watchdog hardware timer will do a reset and disable all outputs
  1712. * if the firmware gets too overloaded to read the temperature sensors.
  1713. *
  1714. * If you find that watchdog reboot causes your AVR board to hang forever,
  1715. * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
  1716. * NOTE: This method is less reliable as it can only catch hangups while
  1717. * interrupts are enabled.
  1718. */
  1719. #define USE_WATCHDOG
  1720. #if ENABLED(USE_WATCHDOG)
  1721. //#define WATCHDOG_RESET_MANUAL
  1722. #endif
  1723. // @section lcd
  1724. /**
  1725. * Babystepping enables movement of the axes by tiny increments without changing
  1726. * the current position values. This feature is used primarily to adjust the Z
  1727. * axis in the first layer of a print in real-time.
  1728. *
  1729. * Warning: Does not respect endstops!
  1730. */
  1731. //#define BABYSTEPPING
  1732. #if ENABLED(BABYSTEPPING)
  1733. //#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR
  1734. //#define BABYSTEP_WITHOUT_HOMING
  1735. //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
  1736. //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  1737. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  1738. //#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
  1739. #define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
  1740. #define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
  1741. //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  1742. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
  1743. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
  1744. // Note: Extra time may be added to mitigate controller latency.
  1745. //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
  1746. #if ENABLED(MOVE_Z_WHEN_IDLE)
  1747. #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size.
  1748. #endif
  1749. #endif
  1750. //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
  1751. //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
  1752. #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
  1753. //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
  1754. //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
  1755. #endif
  1756. #endif
  1757. // @section extruder
  1758. /**
  1759. * Linear Pressure Control v1.5
  1760. *
  1761. * Assumption: advance [steps] = k * (delta velocity [steps/s])
  1762. * K=0 means advance disabled.
  1763. *
  1764. * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
  1765. *
  1766. * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
  1767. * Larger K values will be needed for flexible filament and greater distances.
  1768. * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
  1769. * print acceleration will be reduced during the affected moves to keep within the limit.
  1770. *
  1771. * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  1772. */
  1773. //#define LIN_ADVANCE
  1774. #if ENABLED(LIN_ADVANCE)
  1775. //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
  1776. #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
  1777. //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
  1778. //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
  1779. //#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends.
  1780. #endif
  1781. // @section leveling
  1782. /**
  1783. * Use Safe Bed Leveling coordinates to move axes to a useful position before bed probing.
  1784. * For example, after homing a rotational axis the Z probe might not be perpendicular to the bed.
  1785. * Choose values the orient the bed horizontally and the Z-probe vertically.
  1786. */
  1787. //#define SAFE_BED_LEVELING_START_X 0.0
  1788. //#define SAFE_BED_LEVELING_START_Y 0.0
  1789. //#define SAFE_BED_LEVELING_START_Z 0.0
  1790. //#define SAFE_BED_LEVELING_START_I 0.0
  1791. //#define SAFE_BED_LEVELING_START_J 0.0
  1792. //#define SAFE_BED_LEVELING_START_K 0.0
  1793. //#define SAFE_BED_LEVELING_START_U 0.0
  1794. //#define SAFE_BED_LEVELING_START_V 0.0
  1795. //#define SAFE_BED_LEVELING_START_W 0.0
  1796. /**
  1797. * Points to probe for all 3-point Leveling procedures.
  1798. * Override if the automatically selected points are inadequate.
  1799. */
  1800. #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
  1801. //#define PROBE_PT_1_X 15
  1802. //#define PROBE_PT_1_Y 180
  1803. //#define PROBE_PT_2_X 15
  1804. //#define PROBE_PT_2_Y 20
  1805. //#define PROBE_PT_3_X 170
  1806. //#define PROBE_PT_3_Y 20
  1807. #endif
  1808. /**
  1809. * Probing Margins
  1810. *
  1811. * Override PROBING_MARGIN for each side of the build plate
  1812. * Useful to get probe points to exact positions on targets or
  1813. * to allow leveling to avoid plate clamps on only specific
  1814. * sides of the bed. With NOZZLE_AS_PROBE negative values are
  1815. * allowed, to permit probing outside the bed.
  1816. *
  1817. * If you are replacing the prior *_PROBE_BED_POSITION options,
  1818. * LEFT and FRONT values in most cases will map directly over
  1819. * RIGHT and REAR would be the inverse such as
  1820. * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
  1821. *
  1822. * This will allow all positions to match at compilation, however
  1823. * should the probe position be modified with M851XY then the
  1824. * probe points will follow. This prevents any change from causing
  1825. * the probe to be unable to reach any points.
  1826. */
  1827. #if PROBE_SELECTED && !IS_KINEMATIC
  1828. //#define PROBING_MARGIN_LEFT PROBING_MARGIN
  1829. //#define PROBING_MARGIN_RIGHT PROBING_MARGIN
  1830. //#define PROBING_MARGIN_FRONT PROBING_MARGIN
  1831. //#define PROBING_MARGIN_BACK PROBING_MARGIN
  1832. #endif
  1833. #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
  1834. // Override the mesh area if the automatic (max) area is too large
  1835. //#define MESH_MIN_X MESH_INSET
  1836. //#define MESH_MIN_Y MESH_INSET
  1837. //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
  1838. //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
  1839. #endif
  1840. #if BOTH(AUTO_BED_LEVELING_UBL, EEPROM_SETTINGS)
  1841. //#define OPTIMIZED_MESH_STORAGE // Store mesh with less precision to save EEPROM space
  1842. #endif
  1843. /**
  1844. * Repeatedly attempt G29 leveling until it succeeds.
  1845. * Stop after G29_MAX_RETRIES attempts.
  1846. */
  1847. //#define G29_RETRY_AND_RECOVER
  1848. #if ENABLED(G29_RETRY_AND_RECOVER)
  1849. #define G29_MAX_RETRIES 3
  1850. #define G29_HALT_ON_FAILURE
  1851. /**
  1852. * Specify the GCODE commands that will be executed when leveling succeeds,
  1853. * between attempts, and after the maximum number of retries have been tried.
  1854. */
  1855. #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
  1856. #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
  1857. #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
  1858. #endif
  1859. /**
  1860. * Thermal Probe Compensation
  1861. *
  1862. * Adjust probe measurements to compensate for distortion associated with the temperature
  1863. * of the probe, bed, and/or hotend.
  1864. * Use G76 to automatically calibrate this feature for probe and bed temperatures.
  1865. * (Extruder temperature/offset values must be calibrated manually.)
  1866. * Use M871 to set temperature/offset values manually.
  1867. * For more details see https://marlinfw.org/docs/features/probe_temp_compensation.html
  1868. */
  1869. //#define PTC_PROBE // Compensate based on probe temperature
  1870. //#define PTC_BED // Compensate based on bed temperature
  1871. //#define PTC_HOTEND // Compensate based on hotend temperature
  1872. #if ANY(PTC_PROBE, PTC_BED, PTC_HOTEND)
  1873. /**
  1874. * If the probe is outside the defined range, use linear extrapolation with the closest
  1875. * point and the point with index PTC_LINEAR_EXTRAPOLATION. e.g., If set to 4 it will use the
  1876. * linear extrapolation between data[0] and data[4] for values below PTC_PROBE_START.
  1877. */
  1878. //#define PTC_LINEAR_EXTRAPOLATION 4
  1879. #if ENABLED(PTC_PROBE)
  1880. // Probe temperature calibration generates a table of values starting at PTC_PROBE_START
  1881. // (e.g., 30), in steps of PTC_PROBE_RES (e.g., 5) with PTC_PROBE_COUNT (e.g., 10) samples.
  1882. #define PTC_PROBE_START 30 // (°C)
  1883. #define PTC_PROBE_RES 5 // (°C)
  1884. #define PTC_PROBE_COUNT 10
  1885. #define PTC_PROBE_ZOFFS { 0 } // (µm) Z adjustments per sample
  1886. #endif
  1887. #if ENABLED(PTC_BED)
  1888. // Bed temperature calibration builds a similar table.
  1889. #define PTC_BED_START 60 // (°C)
  1890. #define PTC_BED_RES 5 // (°C)
  1891. #define PTC_BED_COUNT 10
  1892. #define PTC_BED_ZOFFS { 0 } // (µm) Z adjustments per sample
  1893. #endif
  1894. #if ENABLED(PTC_HOTEND)
  1895. // Note: There is no automatic calibration for the hotend. Use M871.
  1896. #define PTC_HOTEND_START 180 // (°C)
  1897. #define PTC_HOTEND_RES 5 // (°C)
  1898. #define PTC_HOTEND_COUNT 20
  1899. #define PTC_HOTEND_ZOFFS { 0 } // (µm) Z adjustments per sample
  1900. #endif
  1901. // G76 options
  1902. #if BOTH(PTC_PROBE, PTC_BED)
  1903. // Park position to wait for probe cooldown
  1904. #define PTC_PARK_POS { 0, 0, 100 }
  1905. // Probe position to probe and wait for probe to reach target temperature
  1906. //#define PTC_PROBE_POS { 12.0f, 7.3f } // Example: MK52 magnetic heatbed
  1907. #define PTC_PROBE_POS { 90, 100 }
  1908. // The temperature the probe should be at while taking measurements during
  1909. // bed temperature calibration.
  1910. #define PTC_PROBE_TEMP 30 // (°C)
  1911. // Height above Z=0.0 to raise the nozzle. Lowering this can help the probe to heat faster.
  1912. // Note: The Z=0.0 offset is determined by the probe Z offset (e.g., as set with M851 Z).
  1913. #define PTC_PROBE_HEATING_OFFSET 0.5
  1914. #endif
  1915. #endif // PTC_PROBE || PTC_BED || PTC_HOTEND
  1916. // @section extras
  1917. //
  1918. // G60/G61 Position Save and Return
  1919. //
  1920. //#define SAVED_POSITIONS 1 // Each saved position slot costs 12 bytes
  1921. //
  1922. // G2/G3 Arc Support
  1923. //
  1924. #define ARC_SUPPORT // Requires ~3226 bytes
  1925. #if ENABLED(ARC_SUPPORT)
  1926. #define MIN_ARC_SEGMENT_MM 0.1 // (mm) Minimum length of each arc segment
  1927. #define MAX_ARC_SEGMENT_MM 1.0 // (mm) Maximum length of each arc segment
  1928. #define MIN_CIRCLE_SEGMENTS 72 // Minimum number of segments in a complete circle
  1929. //#define ARC_SEGMENTS_PER_SEC 50 // Use the feedrate to choose the segment length
  1930. #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections
  1931. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  1932. //#define SF_ARC_FIX // Enable only if using SkeinForge with "Arc Point" fillet procedure
  1933. #endif
  1934. // G5 Bézier Curve Support with XYZE destination and IJPQ offsets
  1935. //#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes
  1936. #if EITHER(ARC_SUPPORT, BEZIER_CURVE_SUPPORT)
  1937. //#define CNC_WORKSPACE_PLANES // Allow G2/G3/G5 to operate in XY, ZX, or YZ planes
  1938. #endif
  1939. /**
  1940. * Direct Stepping
  1941. *
  1942. * Comparable to the method used by Klipper, G6 direct stepping significantly
  1943. * reduces motion calculations, increases top printing speeds, and results in
  1944. * less step aliasing by calculating all motions in advance.
  1945. * Preparing your G-code: https://github.com/colinrgodsey/step-daemon
  1946. */
  1947. //#define DIRECT_STEPPING
  1948. /**
  1949. * G38 Probe Target
  1950. *
  1951. * This option adds G38.2 and G38.3 (probe towards target)
  1952. * and optionally G38.4 and G38.5 (probe away from target).
  1953. * Set MULTIPLE_PROBING for G38 to probe more than once.
  1954. */
  1955. //#define G38_PROBE_TARGET
  1956. #if ENABLED(G38_PROBE_TARGET)
  1957. //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target
  1958. #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move.
  1959. #endif
  1960. // Moves (or segments) with fewer steps than this will be joined with the next move
  1961. #define MIN_STEPS_PER_SEGMENT 6
  1962. /**
  1963. * Minimum delay before and after setting the stepper DIR (in ns)
  1964. * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
  1965. * 20 : Minimum for TMC2xxx drivers
  1966. * 200 : Minimum for A4988 drivers
  1967. * 400 : Minimum for A5984 drivers
  1968. * 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
  1969. * 650 : Minimum for DRV8825 drivers
  1970. * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
  1971. * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
  1972. *
  1973. * Override the default value based on the driver type set in Configuration.h.
  1974. */
  1975. //#define MINIMUM_STEPPER_POST_DIR_DELAY 650
  1976. //#define MINIMUM_STEPPER_PRE_DIR_DELAY 650
  1977. /**
  1978. * Minimum stepper driver pulse width (in µs)
  1979. * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
  1980. * 0 : Minimum 500ns for LV8729, adjusted in stepper.h
  1981. * 1 : Minimum for A4988 and A5984 stepper drivers
  1982. * 2 : Minimum for DRV8825 stepper drivers
  1983. * 3 : Minimum for TB6600 stepper drivers
  1984. * 30 : Minimum for TB6560 stepper drivers
  1985. *
  1986. * Override the default value based on the driver type set in Configuration.h.
  1987. */
  1988. //#define MINIMUM_STEPPER_PULSE 2
  1989. /**
  1990. * Maximum stepping rate (in Hz) the stepper driver allows
  1991. * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
  1992. * 5000000 : Maximum for TMC2xxx stepper drivers
  1993. * 1000000 : Maximum for LV8729 stepper driver
  1994. * 500000 : Maximum for A4988 stepper driver
  1995. * 250000 : Maximum for DRV8825 stepper driver
  1996. * 150000 : Maximum for TB6600 stepper driver
  1997. * 15000 : Maximum for TB6560 stepper driver
  1998. *
  1999. * Override the default value based on the driver type set in Configuration.h.
  2000. */
  2001. //#define MAXIMUM_STEPPER_RATE 250000
  2002. // @section temperature
  2003. // Control heater 0 and heater 1 in parallel.
  2004. //#define HEATERS_PARALLEL
  2005. //===========================================================================
  2006. //================================= Buffers =================================
  2007. //===========================================================================
  2008. // @section motion
  2009. // The number of linear moves that can be in the planner at once.
  2010. // The value of BLOCK_BUFFER_SIZE must be a power of 2 (e.g., 8, 16, 32)
  2011. #if BOTH(SDSUPPORT, DIRECT_STEPPING)
  2012. #define BLOCK_BUFFER_SIZE 8
  2013. #elif ENABLED(SDSUPPORT)
  2014. #define BLOCK_BUFFER_SIZE 16
  2015. #else
  2016. #define BLOCK_BUFFER_SIZE 16
  2017. #endif
  2018. // @section serial
  2019. // The ASCII buffer for serial input
  2020. #define MAX_CMD_SIZE 96
  2021. #define BUFSIZE 4
  2022. // Transmission to Host Buffer Size
  2023. // To save 386 bytes of flash (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  2024. // To buffer a simple "ok" you need 4 bytes.
  2025. // For ADVANCED_OK (M105) you need 32 bytes.
  2026. // For debug-echo: 128 bytes for the optimal speed.
  2027. // Other output doesn't need to be that speedy.
  2028. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  2029. #define TX_BUFFER_SIZE 0
  2030. // Host Receive Buffer Size
  2031. // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
  2032. // To use flow control, set this buffer size to at least 1024 bytes.
  2033. // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
  2034. //#define RX_BUFFER_SIZE 1024
  2035. #if RX_BUFFER_SIZE >= 1024
  2036. // Enable to have the controller send XON/XOFF control characters to
  2037. // the host to signal the RX buffer is becoming full.
  2038. //#define SERIAL_XON_XOFF
  2039. #endif
  2040. #if ENABLED(SDSUPPORT)
  2041. // Enable this option to collect and display the maximum
  2042. // RX queue usage after transferring a file to SD.
  2043. //#define SERIAL_STATS_MAX_RX_QUEUED
  2044. // Enable this option to collect and display the number
  2045. // of dropped bytes after a file transfer to SD.
  2046. //#define SERIAL_STATS_DROPPED_RX
  2047. #endif
  2048. // Monitor RX buffer usage
  2049. // Dump an error to the serial port if the serial receive buffer overflows.
  2050. // If you see these errors, increase the RX_BUFFER_SIZE value.
  2051. // Not supported on all platforms.
  2052. //#define RX_BUFFER_MONITOR
  2053. /**
  2054. * Emergency Command Parser
  2055. *
  2056. * Add a low-level parser to intercept certain commands as they
  2057. * enter the serial receive buffer, so they cannot be blocked.
  2058. * Currently handles M108, M112, M410, M876
  2059. * NOTE: Not yet implemented for all platforms.
  2060. */
  2061. //#define EMERGENCY_PARSER
  2062. /**
  2063. * Realtime Reporting (requires EMERGENCY_PARSER)
  2064. *
  2065. * - Report position and state of the machine (like Grbl).
  2066. * - Auto-report position during long moves.
  2067. * - Useful for CNC/LASER.
  2068. *
  2069. * Adds support for commands:
  2070. * S000 : Report State and Position while moving.
  2071. * P000 : Instant Pause / Hold while moving.
  2072. * R000 : Resume from Pause / Hold.
  2073. *
  2074. * - During Hold all Emergency Parser commands are available, as usual.
  2075. * - Enable NANODLP_Z_SYNC and NANODLP_ALL_AXIS for move command end-state reports.
  2076. */
  2077. //#define REALTIME_REPORTING_COMMANDS
  2078. #if ENABLED(REALTIME_REPORTING_COMMANDS)
  2079. //#define FULL_REPORT_TO_HOST_FEATURE // Auto-report the machine status like Grbl CNC
  2080. #endif
  2081. // Bad Serial-connections can miss a received command by sending an 'ok'
  2082. // Therefore some clients abort after 30 seconds in a timeout.
  2083. // Some other clients start sending commands while receiving a 'wait'.
  2084. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  2085. //#define NO_TIMEOUTS 1000 // Milliseconds
  2086. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  2087. //#define ADVANCED_OK
  2088. // Printrun may have trouble receiving long strings all at once.
  2089. // This option inserts short delays between lines of serial output.
  2090. #define SERIAL_OVERRUN_PROTECTION
  2091. // For serial echo, the number of digits after the decimal point
  2092. //#define SERIAL_FLOAT_PRECISION 4
  2093. /**
  2094. * Set the number of proportional font spaces required to fill up a typical character space.
  2095. * This can help to better align the output of commands like `G29 O` Mesh Output.
  2096. *
  2097. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  2098. * Otherwise, adjust according to your client and font.
  2099. */
  2100. #define PROPORTIONAL_FONT_RATIO 1.0
  2101. // @section extras
  2102. /**
  2103. * Extra Fan Speed
  2104. * Adds a secondary fan speed for each print-cooling fan.
  2105. * 'M106 P<fan> T3-255' : Set a secondary speed for <fan>
  2106. * 'M106 P<fan> T2' : Use the set secondary speed
  2107. * 'M106 P<fan> T1' : Restore the previous fan speed
  2108. */
  2109. //#define EXTRA_FAN_SPEED
  2110. /**
  2111. * Firmware-based and LCD-controlled retract
  2112. *
  2113. * Add G10 / G11 commands for automatic firmware-based retract / recover.
  2114. * Use M207 and M208 to define parameters for retract / recover.
  2115. *
  2116. * Use M209 to enable or disable auto-retract.
  2117. * With auto-retract enabled, all G1 E moves within the set range
  2118. * will be converted to firmware-based retract/recover moves.
  2119. *
  2120. * Be sure to turn off auto-retract during filament change.
  2121. *
  2122. * Note that M207 / M208 / M209 settings are saved to EEPROM.
  2123. */
  2124. //#define FWRETRACT
  2125. #if ENABLED(FWRETRACT)
  2126. #define FWRETRACT_AUTORETRACT // Override slicer retractions
  2127. #if ENABLED(FWRETRACT_AUTORETRACT)
  2128. #define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length
  2129. #define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length
  2130. #endif
  2131. #define RETRACT_LENGTH 3 // (mm) Default retract length (positive value)
  2132. #define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value)
  2133. #define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting
  2134. #define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise
  2135. #define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover)
  2136. #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
  2137. #define RETRACT_RECOVER_FEEDRATE 8 // (mm/s) Default feedrate for recovering from retraction
  2138. #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction
  2139. #if ENABLED(MIXING_EXTRUDER)
  2140. //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously
  2141. #endif
  2142. #endif
  2143. /**
  2144. * Universal tool change settings.
  2145. * Applies to all types of extruders except where explicitly noted.
  2146. */
  2147. #if HAS_MULTI_EXTRUDER
  2148. // Z raise distance for tool-change, as needed for some extruders
  2149. #define TOOLCHANGE_ZRAISE 2 // (mm)
  2150. //#define TOOLCHANGE_ZRAISE_BEFORE_RETRACT // Apply raise before swap retraction (if enabled)
  2151. //#define TOOLCHANGE_NO_RETURN // Never return to previous position on tool-change
  2152. #if ENABLED(TOOLCHANGE_NO_RETURN)
  2153. //#define EVENT_GCODE_AFTER_TOOLCHANGE "G12X" // Extra G-code to run after tool-change
  2154. #endif
  2155. /**
  2156. * Extra G-code to run while executing tool-change commands. Can be used to use an additional
  2157. * stepper motor (e.g., I axis in Configuration.h) to drive the tool-changer.
  2158. */
  2159. //#define EVENT_GCODE_TOOLCHANGE_T0 "G28 A\nG1 A0" // Extra G-code to run while executing tool-change command T0
  2160. //#define EVENT_GCODE_TOOLCHANGE_T1 "G1 A10" // Extra G-code to run while executing tool-change command T1
  2161. //#define EVENT_GCODE_TOOLCHANGE_ALWAYS_RUN // Always execute above G-code sequences. Use with caution!
  2162. /**
  2163. * Tool Sensors detect when tools have been picked up or dropped.
  2164. * Requires the pins TOOL_SENSOR1_PIN, TOOL_SENSOR2_PIN, etc.
  2165. */
  2166. //#define TOOL_SENSOR
  2167. /**
  2168. * Retract and prime filament on tool-change to reduce
  2169. * ooze and stringing and to get cleaner transitions.
  2170. */
  2171. //#define TOOLCHANGE_FILAMENT_SWAP
  2172. #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
  2173. // Load / Unload
  2174. #define TOOLCHANGE_FS_LENGTH 12 // (mm) Load / Unload length
  2175. #define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH 0 // (mm) Extra length for better restart. Adjust with LCD or M217 B.
  2176. #define TOOLCHANGE_FS_RETRACT_SPEED (50*60) // (mm/min) (Unloading)
  2177. #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/min) (On SINGLENOZZLE or Bowden loading must be slowed down)
  2178. // Longer prime to clean out a SINGLENOZZLE
  2179. #define TOOLCHANGE_FS_EXTRA_PRIME 0 // (mm) Extra priming length
  2180. #define TOOLCHANGE_FS_PRIME_SPEED (4.6*60) // (mm/min) Extra priming feedrate
  2181. #define TOOLCHANGE_FS_WIPE_RETRACT 0 // (mm) Retract before cooling for less stringing, better wipe, etc.
  2182. // Cool after prime to reduce stringing
  2183. #define TOOLCHANGE_FS_FAN -1 // Fan index or -1 to skip
  2184. #define TOOLCHANGE_FS_FAN_SPEED 255 // 0-255
  2185. #define TOOLCHANGE_FS_FAN_TIME 10 // (seconds)
  2186. // Use TOOLCHANGE_FS_PRIME_SPEED feedrate the first time each extruder is primed
  2187. //#define TOOLCHANGE_FS_SLOW_FIRST_PRIME
  2188. /**
  2189. * Prime T0 the first time T0 is sent to the printer:
  2190. * [ Power-On -> T0 { Activate & Prime T0 } -> T1 { Retract T0, Activate & Prime T1 } ]
  2191. * If disabled, no priming on T0 until switching back to T0 from another extruder:
  2192. * [ Power-On -> T0 { T0 Activated } -> T1 { Activate & Prime T1 } -> T0 { Retract T1, Activate & Prime T0 } ]
  2193. * Enable with M217 V1 before printing to avoid unwanted priming on host connect.
  2194. */
  2195. //#define TOOLCHANGE_FS_PRIME_FIRST_USED
  2196. /**
  2197. * Tool Change Migration
  2198. * This feature provides G-code and LCD options to switch tools mid-print.
  2199. * All applicable tool properties are migrated so the print can continue.
  2200. * Tools must be closely matching and other restrictions may apply.
  2201. * Useful to:
  2202. * - Change filament color without interruption
  2203. * - Switch spools automatically on filament runout
  2204. * - Switch to a different nozzle on an extruder jam
  2205. */
  2206. #define TOOLCHANGE_MIGRATION_FEATURE
  2207. #endif
  2208. /**
  2209. * Position to park head during tool change.
  2210. * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER
  2211. */
  2212. //#define TOOLCHANGE_PARK
  2213. #if ENABLED(TOOLCHANGE_PARK)
  2214. #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 }
  2215. #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/min)
  2216. //#define TOOLCHANGE_PARK_X_ONLY // X axis only move
  2217. //#define TOOLCHANGE_PARK_Y_ONLY // Y axis only move
  2218. #endif
  2219. #endif // HAS_MULTI_EXTRUDER
  2220. /**
  2221. * Advanced Pause for Filament Change
  2222. * - Adds the G-code M600 Filament Change to initiate a filament change.
  2223. * - This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  2224. *
  2225. * Requirements:
  2226. * - For Filament Change parking enable and configure NOZZLE_PARK_FEATURE.
  2227. * - For user interaction enable an LCD display, HOST_PROMPT_SUPPORT, or EMERGENCY_PARSER.
  2228. *
  2229. * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  2230. */
  2231. //#define ADVANCED_PAUSE_FEATURE
  2232. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  2233. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
  2234. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
  2235. // This short retract is done immediately, before parking the nozzle.
  2236. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
  2237. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  2238. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
  2239. // For Bowden, the full length of the tube and nozzle.
  2240. // For direct drive, the full length of the nozzle.
  2241. // Set to 0 for manual unloading.
  2242. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
  2243. #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
  2244. // 0 to disable start loading and skip to fast load only
  2245. #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
  2246. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  2247. #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
  2248. // For Bowden, the full length of the tube and nozzle.
  2249. // For direct drive, the full length of the nozzle.
  2250. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
  2251. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
  2252. #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
  2253. // Set to 0 for manual extrusion.
  2254. // Filament can be extruded repeatedly from the Filament Change menu
  2255. // until extrusion is consistent, and to purge old filament.
  2256. #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
  2257. //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
  2258. // Filament Unload does a Retract, Delay, and Purge first:
  2259. #define FILAMENT_UNLOAD_PURGE_RETRACT 13 // (mm) Unload initial retract length.
  2260. #define FILAMENT_UNLOAD_PURGE_DELAY 5000 // (ms) Delay for the filament to cool after retract.
  2261. #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
  2262. #define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload
  2263. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
  2264. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
  2265. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
  2266. //#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again.
  2267. //#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing.
  2268. //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
  2269. //#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
  2270. //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
  2271. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
  2272. #endif
  2273. // @section tmc
  2274. /**
  2275. * TMC26X Stepper Driver options
  2276. *
  2277. * The TMC26XStepper library is required for this stepper driver.
  2278. * https://github.com/trinamic/TMC26XStepper
  2279. */
  2280. #if HAS_DRIVER(TMC26X)
  2281. #if AXIS_DRIVER_TYPE_X(TMC26X)
  2282. #define X_MAX_CURRENT 1000 // (mA)
  2283. #define X_SENSE_RESISTOR 91 // (mOhms)
  2284. #define X_MICROSTEPS 16 // Number of microsteps
  2285. #endif
  2286. #if AXIS_DRIVER_TYPE_X2(TMC26X)
  2287. #define X2_MAX_CURRENT 1000
  2288. #define X2_SENSE_RESISTOR 91
  2289. #define X2_MICROSTEPS X_MICROSTEPS
  2290. #endif
  2291. #if AXIS_DRIVER_TYPE_Y(TMC26X)
  2292. #define Y_MAX_CURRENT 1000
  2293. #define Y_SENSE_RESISTOR 91
  2294. #define Y_MICROSTEPS 16
  2295. #endif
  2296. #if AXIS_DRIVER_TYPE_Y2(TMC26X)
  2297. #define Y2_MAX_CURRENT 1000
  2298. #define Y2_SENSE_RESISTOR 91
  2299. #define Y2_MICROSTEPS Y_MICROSTEPS
  2300. #endif
  2301. #if AXIS_DRIVER_TYPE_Z(TMC26X)
  2302. #define Z_MAX_CURRENT 1000
  2303. #define Z_SENSE_RESISTOR 91
  2304. #define Z_MICROSTEPS 16
  2305. #endif
  2306. #if AXIS_DRIVER_TYPE_Z2(TMC26X)
  2307. #define Z2_MAX_CURRENT 1000
  2308. #define Z2_SENSE_RESISTOR 91
  2309. #define Z2_MICROSTEPS Z_MICROSTEPS
  2310. #endif
  2311. #if AXIS_DRIVER_TYPE_Z3(TMC26X)
  2312. #define Z3_MAX_CURRENT 1000
  2313. #define Z3_SENSE_RESISTOR 91
  2314. #define Z3_MICROSTEPS Z_MICROSTEPS
  2315. #endif
  2316. #if AXIS_DRIVER_TYPE_Z4(TMC26X)
  2317. #define Z4_MAX_CURRENT 1000
  2318. #define Z4_SENSE_RESISTOR 91
  2319. #define Z4_MICROSTEPS Z_MICROSTEPS
  2320. #endif
  2321. #if AXIS_DRIVER_TYPE_I(TMC26X)
  2322. #define I_MAX_CURRENT 1000
  2323. #define I_SENSE_RESISTOR 91
  2324. #define I_MICROSTEPS 16
  2325. #endif
  2326. #if AXIS_DRIVER_TYPE_J(TMC26X)
  2327. #define J_MAX_CURRENT 1000
  2328. #define J_SENSE_RESISTOR 91
  2329. #define J_MICROSTEPS 16
  2330. #endif
  2331. #if AXIS_DRIVER_TYPE_K(TMC26X)
  2332. #define K_MAX_CURRENT 1000
  2333. #define K_SENSE_RESISTOR 91
  2334. #define K_MICROSTEPS 16
  2335. #endif
  2336. #if AXIS_DRIVER_TYPE_U(TMC26X)
  2337. #define U_MAX_CURRENT 1000
  2338. #define U_SENSE_RESISTOR 91
  2339. #define U_MICROSTEPS 16
  2340. #endif
  2341. #if AXIS_DRIVER_TYPE_V(TMC26X)
  2342. #define V_MAX_CURRENT 1000
  2343. #define V_SENSE_RESISTOR 91
  2344. #define V_MICROSTEPS 16
  2345. #endif
  2346. #if AXIS_DRIVER_TYPE_W(TMC26X)
  2347. #define W_MAX_CURRENT 1000
  2348. #define W_SENSE_RESISTOR 91
  2349. #define W_MICROSTEPS 16
  2350. #endif
  2351. #if AXIS_DRIVER_TYPE_E0(TMC26X)
  2352. #define E0_MAX_CURRENT 1000
  2353. #define E0_SENSE_RESISTOR 91
  2354. #define E0_MICROSTEPS 16
  2355. #endif
  2356. #if AXIS_DRIVER_TYPE_E1(TMC26X)
  2357. #define E1_MAX_CURRENT 1000
  2358. #define E1_SENSE_RESISTOR 91
  2359. #define E1_MICROSTEPS E0_MICROSTEPS
  2360. #endif
  2361. #if AXIS_DRIVER_TYPE_E2(TMC26X)
  2362. #define E2_MAX_CURRENT 1000
  2363. #define E2_SENSE_RESISTOR 91
  2364. #define E2_MICROSTEPS E0_MICROSTEPS
  2365. #endif
  2366. #if AXIS_DRIVER_TYPE_E3(TMC26X)
  2367. #define E3_MAX_CURRENT 1000
  2368. #define E3_SENSE_RESISTOR 91
  2369. #define E3_MICROSTEPS E0_MICROSTEPS
  2370. #endif
  2371. #if AXIS_DRIVER_TYPE_E4(TMC26X)
  2372. #define E4_MAX_CURRENT 1000
  2373. #define E4_SENSE_RESISTOR 91
  2374. #define E4_MICROSTEPS E0_MICROSTEPS
  2375. #endif
  2376. #if AXIS_DRIVER_TYPE_E5(TMC26X)
  2377. #define E5_MAX_CURRENT 1000
  2378. #define E5_SENSE_RESISTOR 91
  2379. #define E5_MICROSTEPS E0_MICROSTEPS
  2380. #endif
  2381. #if AXIS_DRIVER_TYPE_E6(TMC26X)
  2382. #define E6_MAX_CURRENT 1000
  2383. #define E6_SENSE_RESISTOR 91
  2384. #define E6_MICROSTEPS E0_MICROSTEPS
  2385. #endif
  2386. #if AXIS_DRIVER_TYPE_E7(TMC26X)
  2387. #define E7_MAX_CURRENT 1000
  2388. #define E7_SENSE_RESISTOR 91
  2389. #define E7_MICROSTEPS E0_MICROSTEPS
  2390. #endif
  2391. #endif // TMC26X
  2392. // @section tmc_smart
  2393. /**
  2394. * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode
  2395. * connect your SPI pins to the hardware SPI interface on your board and define
  2396. * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3
  2397. * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  2398. * You may also use software SPI if you wish to use general purpose IO pins.
  2399. *
  2400. * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN
  2401. * to the driver side PDN_UART pin with a 1K resistor.
  2402. * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without
  2403. * a resistor.
  2404. * The drivers can also be used with hardware serial.
  2405. *
  2406. * TMCStepper library is required to use TMC stepper drivers.
  2407. * https://github.com/teemuatlut/TMCStepper
  2408. */
  2409. #if HAS_TRINAMIC_CONFIG
  2410. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  2411. /**
  2412. * Interpolate microsteps to 256
  2413. * Override for each driver with <driver>_INTERPOLATE settings below
  2414. */
  2415. #define INTERPOLATE true
  2416. #if AXIS_IS_TMC(X)
  2417. #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current.
  2418. #define X_CURRENT_HOME X_CURRENT // (mA) RMS current for sensorless homing
  2419. #define X_MICROSTEPS 16 // 0..256
  2420. #define X_RSENSE 0.11
  2421. #define X_CHAIN_POS -1 // -1..0: Not chained. 1: MCU MOSI connected. 2: Next in chain, ...
  2422. //#define X_INTERPOLATE true // Enable to override 'INTERPOLATE' for the X axis
  2423. //#define X_HOLD_MULTIPLIER 0.5 // Enable to override 'HOLD_MULTIPLIER' for the X axis
  2424. #endif
  2425. #if AXIS_IS_TMC(X2)
  2426. #define X2_CURRENT 800
  2427. #define X2_CURRENT_HOME X2_CURRENT
  2428. #define X2_MICROSTEPS X_MICROSTEPS
  2429. #define X2_RSENSE 0.11
  2430. #define X2_CHAIN_POS -1
  2431. //#define X2_INTERPOLATE true
  2432. //#define X2_HOLD_MULTIPLIER 0.5
  2433. #endif
  2434. #if AXIS_IS_TMC(Y)
  2435. #define Y_CURRENT 800
  2436. #define Y_CURRENT_HOME Y_CURRENT
  2437. #define Y_MICROSTEPS 16
  2438. #define Y_RSENSE 0.11
  2439. #define Y_CHAIN_POS -1
  2440. //#define Y_INTERPOLATE true
  2441. //#define Y_HOLD_MULTIPLIER 0.5
  2442. #endif
  2443. #if AXIS_IS_TMC(Y2)
  2444. #define Y2_CURRENT 800
  2445. #define Y2_CURRENT_HOME Y2_CURRENT
  2446. #define Y2_MICROSTEPS Y_MICROSTEPS
  2447. #define Y2_RSENSE 0.11
  2448. #define Y2_CHAIN_POS -1
  2449. //#define Y2_INTERPOLATE true
  2450. //#define Y2_HOLD_MULTIPLIER 0.5
  2451. #endif
  2452. #if AXIS_IS_TMC(Z)
  2453. #define Z_CURRENT 800
  2454. #define Z_CURRENT_HOME Z_CURRENT
  2455. #define Z_MICROSTEPS 16
  2456. #define Z_RSENSE 0.11
  2457. #define Z_CHAIN_POS -1
  2458. //#define Z_INTERPOLATE true
  2459. //#define Z_HOLD_MULTIPLIER 0.5
  2460. #endif
  2461. #if AXIS_IS_TMC(Z2)
  2462. #define Z2_CURRENT 800
  2463. #define Z2_CURRENT_HOME Z2_CURRENT
  2464. #define Z2_MICROSTEPS Z_MICROSTEPS
  2465. #define Z2_RSENSE 0.11
  2466. #define Z2_CHAIN_POS -1
  2467. //#define Z2_INTERPOLATE true
  2468. //#define Z2_HOLD_MULTIPLIER 0.5
  2469. #endif
  2470. #if AXIS_IS_TMC(Z3)
  2471. #define Z3_CURRENT 800
  2472. #define Z3_CURRENT_HOME Z3_CURRENT
  2473. #define Z3_MICROSTEPS Z_MICROSTEPS
  2474. #define Z3_RSENSE 0.11
  2475. #define Z3_CHAIN_POS -1
  2476. //#define Z3_INTERPOLATE true
  2477. //#define Z3_HOLD_MULTIPLIER 0.5
  2478. #endif
  2479. #if AXIS_IS_TMC(Z4)
  2480. #define Z4_CURRENT 800
  2481. #define Z4_CURRENT_HOME Z4_CURRENT
  2482. #define Z4_MICROSTEPS Z_MICROSTEPS
  2483. #define Z4_RSENSE 0.11
  2484. #define Z4_CHAIN_POS -1
  2485. //#define Z4_INTERPOLATE true
  2486. //#define Z4_HOLD_MULTIPLIER 0.5
  2487. #endif
  2488. #if AXIS_IS_TMC(I)
  2489. #define I_CURRENT 800
  2490. #define I_CURRENT_HOME I_CURRENT
  2491. #define I_MICROSTEPS 16
  2492. #define I_RSENSE 0.11
  2493. #define I_CHAIN_POS -1
  2494. //#define I_INTERPOLATE true
  2495. //#define I_HOLD_MULTIPLIER 0.5
  2496. #endif
  2497. #if AXIS_IS_TMC(J)
  2498. #define J_CURRENT 800
  2499. #define J_CURRENT_HOME J_CURRENT
  2500. #define J_MICROSTEPS 16
  2501. #define J_RSENSE 0.11
  2502. #define J_CHAIN_POS -1
  2503. //#define J_INTERPOLATE true
  2504. //#define J_HOLD_MULTIPLIER 0.5
  2505. #endif
  2506. #if AXIS_IS_TMC(K)
  2507. #define K_CURRENT 800
  2508. #define K_CURRENT_HOME K_CURRENT
  2509. #define K_MICROSTEPS 16
  2510. #define K_RSENSE 0.11
  2511. #define K_CHAIN_POS -1
  2512. //#define K_INTERPOLATE true
  2513. //#define K_HOLD_MULTIPLIER 0.5
  2514. #endif
  2515. #if AXIS_IS_TMC(U)
  2516. #define U_CURRENT 800
  2517. #define U_CURRENT_HOME U_CURRENT
  2518. #define U_MICROSTEPS 8
  2519. #define U_RSENSE 0.11
  2520. #define U_CHAIN_POS -1
  2521. //#define U_INTERPOLATE true
  2522. //#define U_HOLD_MULTIPLIER 0.5
  2523. #endif
  2524. #if AXIS_IS_TMC(V)
  2525. #define V_CURRENT 800
  2526. #define V_CURRENT_HOME V_CURRENT
  2527. #define V_MICROSTEPS 8
  2528. #define V_RSENSE 0.11
  2529. #define V_CHAIN_POS -1
  2530. //#define V_INTERPOLATE true
  2531. //#define V_HOLD_MULTIPLIER 0.5
  2532. #endif
  2533. #if AXIS_IS_TMC(W)
  2534. #define W_CURRENT 800
  2535. #define W_CURRENT_HOME W_CURRENT
  2536. #define W_MICROSTEPS 8
  2537. #define W_RSENSE 0.11
  2538. #define W_CHAIN_POS -1
  2539. //#define W_INTERPOLATE true
  2540. //#define W_HOLD_MULTIPLIER 0.5
  2541. #endif
  2542. #if AXIS_IS_TMC(E0)
  2543. #define E0_CURRENT 800
  2544. #define E0_MICROSTEPS 16
  2545. #define E0_RSENSE 0.11
  2546. #define E0_CHAIN_POS -1
  2547. //#define E0_INTERPOLATE true
  2548. //#define E0_HOLD_MULTIPLIER 0.5
  2549. #endif
  2550. #if AXIS_IS_TMC(E1)
  2551. #define E1_CURRENT 800
  2552. #define E1_MICROSTEPS E0_MICROSTEPS
  2553. #define E1_RSENSE 0.11
  2554. #define E1_CHAIN_POS -1
  2555. //#define E1_INTERPOLATE true
  2556. //#define E1_HOLD_MULTIPLIER 0.5
  2557. #endif
  2558. #if AXIS_IS_TMC(E2)
  2559. #define E2_CURRENT 800
  2560. #define E2_MICROSTEPS E0_MICROSTEPS
  2561. #define E2_RSENSE 0.11
  2562. #define E2_CHAIN_POS -1
  2563. //#define E2_INTERPOLATE true
  2564. //#define E2_HOLD_MULTIPLIER 0.5
  2565. #endif
  2566. #if AXIS_IS_TMC(E3)
  2567. #define E3_CURRENT 800
  2568. #define E3_MICROSTEPS E0_MICROSTEPS
  2569. #define E3_RSENSE 0.11
  2570. #define E3_CHAIN_POS -1
  2571. //#define E3_INTERPOLATE true
  2572. //#define E3_HOLD_MULTIPLIER 0.5
  2573. #endif
  2574. #if AXIS_IS_TMC(E4)
  2575. #define E4_CURRENT 800
  2576. #define E4_MICROSTEPS E0_MICROSTEPS
  2577. #define E4_RSENSE 0.11
  2578. #define E4_CHAIN_POS -1
  2579. //#define E4_INTERPOLATE true
  2580. //#define E4_HOLD_MULTIPLIER 0.5
  2581. #endif
  2582. #if AXIS_IS_TMC(E5)
  2583. #define E5_CURRENT 800
  2584. #define E5_MICROSTEPS E0_MICROSTEPS
  2585. #define E5_RSENSE 0.11
  2586. #define E5_CHAIN_POS -1
  2587. //#define E5_INTERPOLATE true
  2588. //#define E5_HOLD_MULTIPLIER 0.5
  2589. #endif
  2590. #if AXIS_IS_TMC(E6)
  2591. #define E6_CURRENT 800
  2592. #define E6_MICROSTEPS E0_MICROSTEPS
  2593. #define E6_RSENSE 0.11
  2594. #define E6_CHAIN_POS -1
  2595. //#define E6_INTERPOLATE true
  2596. //#define E6_HOLD_MULTIPLIER 0.5
  2597. #endif
  2598. #if AXIS_IS_TMC(E7)
  2599. #define E7_CURRENT 800
  2600. #define E7_MICROSTEPS E0_MICROSTEPS
  2601. #define E7_RSENSE 0.11
  2602. #define E7_CHAIN_POS -1
  2603. //#define E7_INTERPOLATE true
  2604. //#define E7_HOLD_MULTIPLIER 0.5
  2605. #endif
  2606. /**
  2607. * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here.
  2608. * The default pins can be found in your board's pins file.
  2609. */
  2610. //#define X_CS_PIN -1
  2611. //#define Y_CS_PIN -1
  2612. //#define Z_CS_PIN -1
  2613. //#define X2_CS_PIN -1
  2614. //#define Y2_CS_PIN -1
  2615. //#define Z2_CS_PIN -1
  2616. //#define Z3_CS_PIN -1
  2617. //#define Z4_CS_PIN -1
  2618. //#define I_CS_PIN -1
  2619. //#define J_CS_PIN -1
  2620. //#define K_CS_PIN -1
  2621. //#define U_CS_PIN -1
  2622. //#define V_CS_PIN -1
  2623. //#define W_CS_PIN -1
  2624. //#define E0_CS_PIN -1
  2625. //#define E1_CS_PIN -1
  2626. //#define E2_CS_PIN -1
  2627. //#define E3_CS_PIN -1
  2628. //#define E4_CS_PIN -1
  2629. //#define E5_CS_PIN -1
  2630. //#define E6_CS_PIN -1
  2631. //#define E7_CS_PIN -1
  2632. /**
  2633. * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160).
  2634. * The default SW SPI pins are defined the respective pins files,
  2635. * but you can override or define them here.
  2636. */
  2637. //#define TMC_USE_SW_SPI
  2638. //#define TMC_SW_MOSI -1
  2639. //#define TMC_SW_MISO -1
  2640. //#define TMC_SW_SCK -1
  2641. /**
  2642. * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses.
  2643. * Set the address using jumpers on pins MS1 and MS2.
  2644. * Address | MS1 | MS2
  2645. * 0 | LOW | LOW
  2646. * 1 | HIGH | LOW
  2647. * 2 | LOW | HIGH
  2648. * 3 | HIGH | HIGH
  2649. *
  2650. * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers
  2651. * on the same serial port, either here or in your board's pins file.
  2652. */
  2653. //#define X_SLAVE_ADDRESS 0
  2654. //#define Y_SLAVE_ADDRESS 0
  2655. //#define Z_SLAVE_ADDRESS 0
  2656. //#define X2_SLAVE_ADDRESS 0
  2657. //#define Y2_SLAVE_ADDRESS 0
  2658. //#define Z2_SLAVE_ADDRESS 0
  2659. //#define Z3_SLAVE_ADDRESS 0
  2660. //#define Z4_SLAVE_ADDRESS 0
  2661. //#define I_SLAVE_ADDRESS 0
  2662. //#define J_SLAVE_ADDRESS 0
  2663. //#define K_SLAVE_ADDRESS 0
  2664. //#define U_SLAVE_ADDRESS 0
  2665. //#define V_SLAVE_ADDRESS 0
  2666. //#define W_SLAVE_ADDRESS 0
  2667. //#define E0_SLAVE_ADDRESS 0
  2668. //#define E1_SLAVE_ADDRESS 0
  2669. //#define E2_SLAVE_ADDRESS 0
  2670. //#define E3_SLAVE_ADDRESS 0
  2671. //#define E4_SLAVE_ADDRESS 0
  2672. //#define E5_SLAVE_ADDRESS 0
  2673. //#define E6_SLAVE_ADDRESS 0
  2674. //#define E7_SLAVE_ADDRESS 0
  2675. /**
  2676. * Software enable
  2677. *
  2678. * Use for drivers that do not use a dedicated enable pin, but rather handle the same
  2679. * function through a communication line such as SPI or UART.
  2680. */
  2681. //#define SOFTWARE_DRIVER_ENABLE
  2682. /**
  2683. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  2684. * Use Trinamic's ultra quiet stepping mode.
  2685. * When disabled, Marlin will use spreadCycle stepping mode.
  2686. */
  2687. #define STEALTHCHOP_XY
  2688. #define STEALTHCHOP_Z
  2689. #define STEALTHCHOP_I
  2690. #define STEALTHCHOP_J
  2691. #define STEALTHCHOP_K
  2692. #define STEALTHCHOP_U
  2693. #define STEALTHCHOP_V
  2694. #define STEALTHCHOP_W
  2695. #define STEALTHCHOP_E
  2696. /**
  2697. * Optimize spreadCycle chopper parameters by using predefined parameter sets
  2698. * or with the help of an example included in the library.
  2699. * Provided parameter sets are
  2700. * CHOPPER_DEFAULT_12V
  2701. * CHOPPER_DEFAULT_19V
  2702. * CHOPPER_DEFAULT_24V
  2703. * CHOPPER_DEFAULT_36V
  2704. * CHOPPER_09STEP_24V // 0.9 degree steppers (24V)
  2705. * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Průša firmware for MK3 (24V)
  2706. * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9
  2707. *
  2708. * Define your own with:
  2709. * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
  2710. */
  2711. #define CHOPPER_TIMING CHOPPER_DEFAULT_12V // All axes (override below)
  2712. //#define CHOPPER_TIMING_X CHOPPER_TIMING // For X Axes (override below)
  2713. //#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X
  2714. //#define CHOPPER_TIMING_Y CHOPPER_TIMING // For Y Axes (override below)
  2715. //#define CHOPPER_TIMING_Y2 CHOPPER_TIMING_Y
  2716. //#define CHOPPER_TIMING_Z CHOPPER_TIMING // For Z Axes (override below)
  2717. //#define CHOPPER_TIMING_Z2 CHOPPER_TIMING_Z
  2718. //#define CHOPPER_TIMING_Z3 CHOPPER_TIMING_Z
  2719. //#define CHOPPER_TIMING_Z4 CHOPPER_TIMING_Z
  2720. //#define CHOPPER_TIMING_I CHOPPER_TIMING // For I Axis
  2721. //#define CHOPPER_TIMING_J CHOPPER_TIMING // For J Axis
  2722. //#define CHOPPER_TIMING_K CHOPPER_TIMING // For K Axis
  2723. //#define CHOPPER_TIMING_U CHOPPER_TIMING // For U Axis
  2724. //#define CHOPPER_TIMING_V CHOPPER_TIMING // For V Axis
  2725. //#define CHOPPER_TIMING_W CHOPPER_TIMING // For W Axis
  2726. //#define CHOPPER_TIMING_E CHOPPER_TIMING // For Extruders (override below)
  2727. //#define CHOPPER_TIMING_E1 CHOPPER_TIMING_E
  2728. //#define CHOPPER_TIMING_E2 CHOPPER_TIMING_E
  2729. //#define CHOPPER_TIMING_E3 CHOPPER_TIMING_E
  2730. //#define CHOPPER_TIMING_E4 CHOPPER_TIMING_E
  2731. //#define CHOPPER_TIMING_E5 CHOPPER_TIMING_E
  2732. //#define CHOPPER_TIMING_E6 CHOPPER_TIMING_E
  2733. //#define CHOPPER_TIMING_E7 CHOPPER_TIMING_E
  2734. /**
  2735. * Monitor Trinamic drivers
  2736. * for error conditions like overtemperature and short to ground.
  2737. * To manage over-temp Marlin can decrease the driver current until the error condition clears.
  2738. * Other detected conditions can be used to stop the current print.
  2739. * Relevant G-codes:
  2740. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  2741. * M911 - Report stepper driver overtemperature pre-warn condition.
  2742. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  2743. * M122 - Report driver parameters (Requires TMC_DEBUG)
  2744. */
  2745. //#define MONITOR_DRIVER_STATUS
  2746. #if ENABLED(MONITOR_DRIVER_STATUS)
  2747. #define CURRENT_STEP_DOWN 50 // [mA]
  2748. #define REPORT_CURRENT_CHANGE
  2749. #define STOP_ON_ERROR
  2750. #endif
  2751. /**
  2752. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  2753. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  2754. * This mode allows for faster movements at the expense of higher noise levels.
  2755. * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
  2756. * M913 X/Y/Z/E to live tune the setting
  2757. */
  2758. //#define HYBRID_THRESHOLD
  2759. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  2760. #define X2_HYBRID_THRESHOLD 100
  2761. #define Y_HYBRID_THRESHOLD 100
  2762. #define Y2_HYBRID_THRESHOLD 100
  2763. #define Z_HYBRID_THRESHOLD 3
  2764. #define Z2_HYBRID_THRESHOLD 3
  2765. #define Z3_HYBRID_THRESHOLD 3
  2766. #define Z4_HYBRID_THRESHOLD 3
  2767. #define I_HYBRID_THRESHOLD 3 // [linear=mm/s, rotational=°/s]
  2768. #define J_HYBRID_THRESHOLD 3 // [linear=mm/s, rotational=°/s]
  2769. #define K_HYBRID_THRESHOLD 3 // [linear=mm/s, rotational=°/s]
  2770. #define U_HYBRID_THRESHOLD 3 // [mm/s]
  2771. #define V_HYBRID_THRESHOLD 3
  2772. #define W_HYBRID_THRESHOLD 3
  2773. #define E0_HYBRID_THRESHOLD 30
  2774. #define E1_HYBRID_THRESHOLD 30
  2775. #define E2_HYBRID_THRESHOLD 30
  2776. #define E3_HYBRID_THRESHOLD 30
  2777. #define E4_HYBRID_THRESHOLD 30
  2778. #define E5_HYBRID_THRESHOLD 30
  2779. #define E6_HYBRID_THRESHOLD 30
  2780. #define E7_HYBRID_THRESHOLD 30
  2781. /**
  2782. * Use StallGuard to home / probe X, Y, Z.
  2783. *
  2784. * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
  2785. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
  2786. * X, Y, and Z homing will always be done in spreadCycle mode.
  2787. *
  2788. * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
  2789. * Use M914 X Y Z to set the stall threshold at runtime:
  2790. *
  2791. * Sensitivity TMC2209 Others
  2792. * HIGHEST 255 -64 (Too sensitive => False positive)
  2793. * LOWEST 0 63 (Too insensitive => No trigger)
  2794. *
  2795. * It is recommended to set HOMING_BUMP_MM to { 0, 0, 0 }.
  2796. *
  2797. * SPI_ENDSTOPS *** Beta feature! *** TMC2130/TMC5160 Only ***
  2798. * Poll the driver through SPI to determine load when homing.
  2799. * Removes the need for a wire from DIAG1 to an endstop pin.
  2800. *
  2801. * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
  2802. * homing and adds a guard period for endstop triggering.
  2803. *
  2804. * Comment *_STALL_SENSITIVITY to disable sensorless homing for that axis.
  2805. */
  2806. //#define SENSORLESS_HOMING // StallGuard capable drivers only
  2807. #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
  2808. // TMC2209: 0...255. TMC2130: -64...63
  2809. #define X_STALL_SENSITIVITY 8
  2810. #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
  2811. #define Y_STALL_SENSITIVITY 8
  2812. #define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
  2813. //#define Z_STALL_SENSITIVITY 8
  2814. //#define Z2_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2815. //#define Z3_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2816. //#define Z4_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2817. //#define I_STALL_SENSITIVITY 8
  2818. //#define J_STALL_SENSITIVITY 8
  2819. //#define K_STALL_SENSITIVITY 8
  2820. //#define U_STALL_SENSITIVITY 8
  2821. //#define V_STALL_SENSITIVITY 8
  2822. //#define W_STALL_SENSITIVITY 8
  2823. //#define SPI_ENDSTOPS // TMC2130 only
  2824. //#define IMPROVE_HOMING_RELIABILITY
  2825. #endif
  2826. /**
  2827. * TMC Homing stepper phase.
  2828. *
  2829. * Improve homing repeatability by homing to stepper coil's nearest absolute
  2830. * phase position. Trinamic drivers use a stepper phase table with 1024 values
  2831. * spanning 4 full steps with 256 positions each (ergo, 1024 positions).
  2832. * Full step positions (128, 384, 640, 896) have the highest holding torque.
  2833. *
  2834. * Values from 0..1023, -1 to disable homing phase for that axis.
  2835. */
  2836. //#define TMC_HOME_PHASE { 896, 896, 896 }
  2837. /**
  2838. * Beta feature!
  2839. * Create a 50/50 square wave step pulse optimal for stepper drivers.
  2840. */
  2841. //#define SQUARE_WAVE_STEPPING
  2842. /**
  2843. * Enable M122 debugging command for TMC stepper drivers.
  2844. * M122 S0/1 will enable continuous reporting.
  2845. */
  2846. //#define TMC_DEBUG
  2847. /**
  2848. * You can set your own advanced settings by filling in predefined functions.
  2849. * A list of available functions can be found on the library github page
  2850. * https://github.com/teemuatlut/TMCStepper
  2851. *
  2852. * Example:
  2853. * #define TMC_ADV() { \
  2854. * stepperX.diag0_otpw(1); \
  2855. * stepperY.intpol(0); \
  2856. * }
  2857. */
  2858. #define TMC_ADV() { }
  2859. #endif // HAS_TRINAMIC_CONFIG
  2860. // @section i2cbus
  2861. //
  2862. // I2C Master ID for LPC176x LCD and Digital Current control
  2863. // Does not apply to other peripherals based on the Wire library.
  2864. //
  2865. //#define I2C_MASTER_ID 1 // Set a value from 0 to 2
  2866. /**
  2867. * TWI/I2C BUS
  2868. *
  2869. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  2870. * machines. Enabling this will allow you to send and receive I2C data from slave
  2871. * devices on the bus.
  2872. *
  2873. * ; Example #1
  2874. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  2875. * ; It uses multiple M260 commands with one B<base 10> arg
  2876. * M260 A99 ; Target slave address
  2877. * M260 B77 ; M
  2878. * M260 B97 ; a
  2879. * M260 B114 ; r
  2880. * M260 B108 ; l
  2881. * M260 B105 ; i
  2882. * M260 B110 ; n
  2883. * M260 S1 ; Send the current buffer
  2884. *
  2885. * ; Example #2
  2886. * ; Request 6 bytes from slave device with address 0x63 (99)
  2887. * M261 A99 B5
  2888. *
  2889. * ; Example #3
  2890. * ; Example serial output of a M261 request
  2891. * echo:i2c-reply: from:99 bytes:5 data:hello
  2892. */
  2893. //#define EXPERIMENTAL_I2CBUS
  2894. #if ENABLED(EXPERIMENTAL_I2CBUS)
  2895. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  2896. #endif
  2897. // @section extras
  2898. /**
  2899. * Photo G-code
  2900. * Add the M240 G-code to take a photo.
  2901. * The photo can be triggered by a digital pin or a physical movement.
  2902. */
  2903. //#define PHOTO_GCODE
  2904. #if ENABLED(PHOTO_GCODE)
  2905. // A position to move to (and raise Z) before taking the photo
  2906. //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z)
  2907. //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P)
  2908. //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S)
  2909. // Canon RC-1 or homebrew digital camera trigger
  2910. // Data from: https://www.doc-diy.net/photo/rc-1_hacked/
  2911. //#define PHOTOGRAPH_PIN 23
  2912. // Canon Hack Development Kit
  2913. // https://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  2914. //#define CHDK_PIN 4
  2915. // Optional second move with delay to trigger the camera shutter
  2916. //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J)
  2917. // Duration to hold the switch or keep CHDK_PIN high
  2918. //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D)
  2919. /**
  2920. * PHOTO_PULSES_US may need adjustment depending on board and camera model.
  2921. * Pin must be running at 48.4kHz.
  2922. * Be sure to use a PHOTOGRAPH_PIN which can rise and fall quick enough.
  2923. * (e.g., MKS SBase temp sensor pin was too slow, so used P1.23 on J8.)
  2924. *
  2925. * Example pulse data for Nikon: https://bit.ly/2FKD0Aq
  2926. * IR Wiring: https://git.io/JvJf7
  2927. */
  2928. //#define PHOTO_PULSES_US { 2000, 27850, 400, 1580, 400, 3580, 400 } // (µs) Durations for each 48.4kHz oscillation
  2929. #ifdef PHOTO_PULSES_US
  2930. #define PHOTO_PULSE_DELAY_US 13 // (µs) Approximate duration of each HIGH and LOW pulse in the oscillation
  2931. #endif
  2932. #endif
  2933. /**
  2934. * Spindle & Laser control
  2935. *
  2936. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  2937. * to set spindle speed, spindle direction, and laser power.
  2938. *
  2939. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  2940. * Marlin can be used to turn the spindle on and off. It can also be used to set
  2941. * the spindle speed from 5,000 to 30,000 RPM.
  2942. *
  2943. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  2944. * hardware PWM pin for the speed control and a pin for the rotation direction.
  2945. *
  2946. * See https://marlinfw.org/docs/configuration/2.0.9/laser_spindle.html for more config details.
  2947. */
  2948. //#define SPINDLE_FEATURE
  2949. //#define LASER_FEATURE
  2950. #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
  2951. #define SPINDLE_LASER_ACTIVE_STATE LOW // Set to "HIGH" if SPINDLE_LASER_ENA_PIN is active HIGH
  2952. #define SPINDLE_LASER_USE_PWM // Enable if your controller supports setting the speed/power
  2953. #if ENABLED(SPINDLE_LASER_USE_PWM)
  2954. #define SPINDLE_LASER_PWM_INVERT false // Set to "true" if the speed/power goes up when you want it to go slower
  2955. #define SPINDLE_LASER_FREQUENCY 2500 // (Hz) Spindle/laser frequency (only on supported HALs: AVR, ESP32, and LPC)
  2956. // ESP32: If SPINDLE_LASER_PWM_PIN is onboard then <=78125Hz. For I2S expander
  2957. // the frequency determines the PWM resolution. 2500Hz = 0-100, 977Hz = 0-255, ...
  2958. // (250000 / SPINDLE_LASER_FREQUENCY) = max value.
  2959. #endif
  2960. //#define AIR_EVACUATION // Cutter Vacuum / Laser Blower motor control with G-codes M10-M11
  2961. #if ENABLED(AIR_EVACUATION)
  2962. #define AIR_EVACUATION_ACTIVE LOW // Set to "HIGH" if the on/off function is active HIGH
  2963. //#define AIR_EVACUATION_PIN 42 // Override the default Cutter Vacuum or Laser Blower pin
  2964. #endif
  2965. //#define AIR_ASSIST // Air Assist control with G-codes M8-M9
  2966. #if ENABLED(AIR_ASSIST)
  2967. #define AIR_ASSIST_ACTIVE LOW // Active state on air assist pin
  2968. //#define AIR_ASSIST_PIN 44 // Override the default Air Assist pin
  2969. #endif
  2970. //#define SPINDLE_SERVO // A servo converting an angle to spindle power
  2971. #ifdef SPINDLE_SERVO
  2972. #define SPINDLE_SERVO_NR 0 // Index of servo used for spindle control
  2973. #define SPINDLE_SERVO_MIN 10 // Minimum angle for servo spindle
  2974. #endif
  2975. /**
  2976. * Speed / Power can be set ('M3 S') and displayed in terms of:
  2977. * - PWM255 (S0 - S255)
  2978. * - PERCENT (S0 - S100)
  2979. * - RPM (S0 - S50000) Best for use with a spindle
  2980. * - SERVO (S0 - S180)
  2981. */
  2982. #define CUTTER_POWER_UNIT PWM255
  2983. /**
  2984. * Relative Cutter Power
  2985. * Normally, 'M3 O<power>' sets
  2986. * OCR power is relative to the range SPEED_POWER_MIN...SPEED_POWER_MAX.
  2987. * so input powers of 0...255 correspond to SPEED_POWER_MIN...SPEED_POWER_MAX
  2988. * instead of normal range (0 to SPEED_POWER_MAX).
  2989. * Best used with (e.g.) SuperPID router controller: S0 = 5,000 RPM and S255 = 30,000 RPM
  2990. */
  2991. //#define CUTTER_POWER_RELATIVE // Set speed proportional to [SPEED_POWER_MIN...SPEED_POWER_MAX]
  2992. #if ENABLED(SPINDLE_FEATURE)
  2993. //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
  2994. #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
  2995. #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
  2996. #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
  2997. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
  2998. /**
  2999. * M3/M4 Power Equation
  3000. *
  3001. * Each tool uses different value ranges for speed / power control.
  3002. * These parameters are used to convert between tool power units and PWM.
  3003. *
  3004. * Speed/Power = (PWMDC / 255 * 100 - SPEED_POWER_INTERCEPT) / SPEED_POWER_SLOPE
  3005. * PWMDC = (spdpwr - SPEED_POWER_MIN) / (SPEED_POWER_MAX - SPEED_POWER_MIN) / SPEED_POWER_SLOPE
  3006. */
  3007. #if ENABLED(SPINDLE_LASER_USE_PWM)
  3008. #define SPEED_POWER_INTERCEPT 0 // (%) 0-100 i.e., Minimum power percentage
  3009. #define SPEED_POWER_MIN 5000 // (RPM)
  3010. #define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
  3011. #define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
  3012. #endif
  3013. #else
  3014. #if ENABLED(SPINDLE_LASER_USE_PWM)
  3015. #define SPEED_POWER_INTERCEPT 0 // (%) 0-100 i.e., Minimum power percentage
  3016. #define SPEED_POWER_MIN 0 // (%) 0-100
  3017. #define SPEED_POWER_MAX 100 // (%) 0-100
  3018. #define SPEED_POWER_STARTUP 80 // (%) M3/M4 speed/power default (with no arguments)
  3019. #endif
  3020. // Define the minimum and maximum test pulse time values for a laser test fire function
  3021. #define LASER_TEST_PULSE_MIN 1 // (ms) Used with Laser Control Menu
  3022. #define LASER_TEST_PULSE_MAX 999 // (ms) Caution: Menu may not show more than 3 characters
  3023. #define SPINDLE_LASER_POWERUP_DELAY 50 // (ms) Delay to allow the spindle/laser to come up to speed/power
  3024. #define SPINDLE_LASER_POWERDOWN_DELAY 50 // (ms) Delay to allow the spindle to stop
  3025. /**
  3026. * Laser Safety Timeout
  3027. *
  3028. * The laser should be turned off when there is no movement for a period of time.
  3029. * Consider material flammability, cut rate, and G-code order when setting this
  3030. * value. Too low and it could turn off during a very slow move; too high and
  3031. * the material could ignite.
  3032. */
  3033. #define LASER_SAFETY_TIMEOUT_MS 1000 // (ms)
  3034. /**
  3035. * Any M3 or G1/2/3/5 command with the 'I' parameter enables continuous inline power mode.
  3036. *
  3037. * e.g., 'M3 I' enables continuous inline power which is processed by the planner.
  3038. * Power is stored in move blocks and applied when blocks are processed by the Stepper ISR.
  3039. *
  3040. * 'M4 I' sets dynamic mode which uses the current feedrate to calculate a laser power OCR value.
  3041. *
  3042. * Any move in dynamic mode will use the current feedrate to calculate the laser power.
  3043. * Feed rates are set by the F parameter of a move command e.g. G1 X0 Y10 F6000
  3044. * Laser power would be calculated by bit shifting off 8 LSB's. In binary this is div 256.
  3045. * The calculation gives us ocr values from 0 to 255, values over F65535 will be set as 255 .
  3046. * More refined power control such as compesation for accell/decell will be addressed in future releases.
  3047. *
  3048. * M5 I clears inline mode and set power to 0, M5 sets the power output to 0 but leaves inline mode on.
  3049. */
  3050. /**
  3051. * Enable M3 commands for laser mode inline power planner syncing.
  3052. * This feature enables any M3 S-value to be injected into the block buffers while in
  3053. * CUTTER_MODE_CONTINUOUS. The option allows M3 laser power to be commited without waiting
  3054. * for a planner syncronization
  3055. */
  3056. //#define LASER_POWER_SYNC
  3057. /**
  3058. * Scale the laser's power in proportion to the movement rate.
  3059. *
  3060. * - Sets the entry power proportional to the entry speed over the nominal speed.
  3061. * - Ramps the power up every N steps to approximate the speed trapezoid.
  3062. * - Due to the limited power resolution this is only approximate.
  3063. */
  3064. //#define LASER_POWER_TRAP
  3065. //
  3066. // Laser I2C Ammeter (High precision INA226 low/high side module)
  3067. //
  3068. //#define I2C_AMMETER
  3069. #if ENABLED(I2C_AMMETER)
  3070. #define I2C_AMMETER_IMAX 0.1 // (Amps) Calibration value for the expected current range
  3071. #define I2C_AMMETER_SHUNT_RESISTOR 0.1 // (Ohms) Calibration shunt resistor value
  3072. #endif
  3073. //
  3074. // Laser Coolant Flow Meter
  3075. //
  3076. //#define LASER_COOLANT_FLOW_METER
  3077. #if ENABLED(LASER_COOLANT_FLOW_METER)
  3078. #define FLOWMETER_PIN 20 // Requires an external interrupt-enabled pin (e.g., RAMPS 2,3,18,19,20,21)
  3079. #define FLOWMETER_PPL 5880 // (pulses/liter) Flow meter pulses-per-liter on the input pin
  3080. #define FLOWMETER_INTERVAL 1000 // (ms) Flow rate calculation interval in milliseconds
  3081. #define FLOWMETER_SAFETY // Prevent running the laser without the minimum flow rate set below
  3082. #if ENABLED(FLOWMETER_SAFETY)
  3083. #define FLOWMETER_MIN_LITERS_PER_MINUTE 1.5 // (liters/min) Minimum flow required when enabled
  3084. #endif
  3085. #endif
  3086. #endif
  3087. #endif // SPINDLE_FEATURE || LASER_FEATURE
  3088. /**
  3089. * Synchronous Laser Control with M106/M107
  3090. *
  3091. * Marlin normally applies M106/M107 fan speeds at a time "soon after" processing
  3092. * a planner block. This is too inaccurate for a PWM/TTL laser attached to the fan
  3093. * header (as with some add-on laser kits). Enable this option to set fan/laser
  3094. * speeds with much more exact timing for improved print fidelity.
  3095. *
  3096. * NOTE: This option sacrifices some cooling fan speed options.
  3097. */
  3098. //#define LASER_SYNCHRONOUS_M106_M107
  3099. /**
  3100. * Coolant Control
  3101. *
  3102. * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off.
  3103. *
  3104. * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined.
  3105. */
  3106. //#define COOLANT_CONTROL
  3107. #if ENABLED(COOLANT_CONTROL)
  3108. #define COOLANT_MIST // Enable if mist coolant is present
  3109. #define COOLANT_FLOOD // Enable if flood coolant is present
  3110. #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed
  3111. #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed
  3112. #endif
  3113. /**
  3114. * Filament Width Sensor
  3115. *
  3116. * Measures the filament width in real-time and adjusts
  3117. * flow rate to compensate for any irregularities.
  3118. *
  3119. * Also allows the measured filament diameter to set the
  3120. * extrusion rate, so the slicer only has to specify the
  3121. * volume.
  3122. *
  3123. * Only a single extruder is supported at this time.
  3124. *
  3125. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  3126. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  3127. * 301 RAMBO : Analog input 3
  3128. *
  3129. * Note: May require analog pins to be defined for other boards.
  3130. */
  3131. //#define FILAMENT_WIDTH_SENSOR
  3132. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  3133. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
  3134. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  3135. #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it
  3136. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  3137. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  3138. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  3139. //#define FILAMENT_LCD_DISPLAY
  3140. #endif
  3141. /**
  3142. * Power Monitor
  3143. * Monitor voltage (V) and/or current (A), and -when possible- power (W)
  3144. *
  3145. * Read and configure with M430
  3146. *
  3147. * The current sensor feeds DC voltage (relative to the measured current) to an analog pin
  3148. * The voltage sensor feeds DC voltage (relative to the measured voltage) to an analog pin
  3149. */
  3150. //#define POWER_MONITOR_CURRENT // Monitor the system current
  3151. //#define POWER_MONITOR_VOLTAGE // Monitor the system voltage
  3152. #if ENABLED(POWER_MONITOR_CURRENT)
  3153. #define POWER_MONITOR_VOLTS_PER_AMP 0.05000 // Input voltage to the MCU analog pin per amp - DO NOT apply more than ADC_VREF!
  3154. #define POWER_MONITOR_CURRENT_OFFSET 0 // Offset (in amps) applied to the calculated current
  3155. #define POWER_MONITOR_FIXED_VOLTAGE 13.6 // Voltage for a current sensor with no voltage sensor (for power display)
  3156. #endif
  3157. #if ENABLED(POWER_MONITOR_VOLTAGE)
  3158. #define POWER_MONITOR_VOLTS_PER_VOLT 0.077933 // Input voltage to the MCU analog pin per volt - DO NOT apply more than ADC_VREF!
  3159. #define POWER_MONITOR_VOLTAGE_OFFSET 0 // Offset (in volts) applied to the calculated voltage
  3160. #endif
  3161. /**
  3162. * Stepper Driver Anti-SNAFU Protection
  3163. *
  3164. * If the SAFE_POWER_PIN is defined for your board, Marlin will check
  3165. * that stepper drivers are properly plugged in before applying power.
  3166. * Disable protection if your stepper drivers don't support the feature.
  3167. */
  3168. //#define DISABLE_DRIVER_SAFE_POWER_PROTECT
  3169. /**
  3170. * CNC Coordinate Systems
  3171. *
  3172. * Enables G53 and G54-G59.3 commands to select coordinate systems
  3173. * and G92.1 to reset the workspace to native machine space.
  3174. */
  3175. //#define CNC_COORDINATE_SYSTEMS
  3176. /**
  3177. * Auto-report fan speed with M123 S<seconds>
  3178. * Requires fans with tachometer pins
  3179. */
  3180. //#define AUTO_REPORT_FANS
  3181. /**
  3182. * Auto-report temperatures with M155 S<seconds>
  3183. */
  3184. #define AUTO_REPORT_TEMPERATURES
  3185. #if ENABLED(AUTO_REPORT_TEMPERATURES) && TEMP_SENSOR_REDUNDANT
  3186. //#define AUTO_REPORT_REDUNDANT // Include the "R" sensor in the auto-report
  3187. #endif
  3188. /**
  3189. * Auto-report position with M154 S<seconds>
  3190. */
  3191. //#define AUTO_REPORT_POSITION
  3192. /**
  3193. * Include capabilities in M115 output
  3194. */
  3195. #define EXTENDED_CAPABILITIES_REPORT
  3196. #if ENABLED(EXTENDED_CAPABILITIES_REPORT)
  3197. //#define M115_GEOMETRY_REPORT
  3198. #endif
  3199. /**
  3200. * Expected Printer Check
  3201. * Add the M16 G-code to compare a string to the MACHINE_NAME.
  3202. * M16 with a non-matching string causes the printer to halt.
  3203. */
  3204. //#define EXPECTED_PRINTER_CHECK
  3205. /**
  3206. * Disable all Volumetric extrusion options
  3207. */
  3208. //#define NO_VOLUMETRICS
  3209. #if DISABLED(NO_VOLUMETRICS)
  3210. /**
  3211. * Volumetric extrusion default state
  3212. * Activate to make volumetric extrusion the default method,
  3213. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  3214. *
  3215. * M200 D0 to disable, M200 Dn to set a new diameter (and enable volumetric).
  3216. * M200 S0/S1 to disable/enable volumetric extrusion.
  3217. */
  3218. //#define VOLUMETRIC_DEFAULT_ON
  3219. //#define VOLUMETRIC_EXTRUDER_LIMIT
  3220. #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT)
  3221. /**
  3222. * Default volumetric extrusion limit in cubic mm per second (mm^3/sec).
  3223. * This factory setting applies to all extruders.
  3224. * Use 'M200 [T<extruder>] L<limit>' to override and 'M502' to reset.
  3225. * A non-zero value activates Volume-based Extrusion Limiting.
  3226. */
  3227. #define DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT 0.00 // (mm^3/sec)
  3228. #endif
  3229. #endif
  3230. /**
  3231. * Enable this option for a leaner build of Marlin that removes all
  3232. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  3233. *
  3234. * - M206 and M428 are disabled.
  3235. * - G92 will revert to its behavior from Marlin 1.0.
  3236. */
  3237. //#define NO_WORKSPACE_OFFSETS
  3238. // Extra options for the M114 "Current Position" report
  3239. //#define M114_DETAIL // Use 'M114` for details to check planner calculations
  3240. //#define M114_REALTIME // Real current position based on forward kinematics
  3241. //#define M114_LEGACY // M114 used to synchronize on every call. Enable if needed.
  3242. //#define REPORT_FAN_CHANGE // Report the new fan speed when changed by M106 (and others)
  3243. /**
  3244. * Spend 28 bytes of SRAM to optimize the G-code parser
  3245. */
  3246. #define FASTER_GCODE_PARSER
  3247. #if ENABLED(FASTER_GCODE_PARSER)
  3248. //#define GCODE_QUOTED_STRINGS // Support for quoted string parameters
  3249. #endif
  3250. // Support for MeatPack G-code compression (https://github.com/scottmudge/OctoPrint-MeatPack)
  3251. //#define MEATPACK_ON_SERIAL_PORT_1
  3252. //#define MEATPACK_ON_SERIAL_PORT_2
  3253. //#define GCODE_CASE_INSENSITIVE // Accept G-code sent to the firmware in lowercase
  3254. //#define REPETIER_GCODE_M360 // Add commands originally from Repetier FW
  3255. /**
  3256. * CNC G-code options
  3257. * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
  3258. * Note that G0 feedrates should be used with care for 3D printing (if used at all).
  3259. * High feedrates may cause ringing and harm print quality.
  3260. */
  3261. //#define PAREN_COMMENTS // Support for parentheses-delimited comments
  3262. //#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
  3263. // Enable and set a (default) feedrate for all G0 moves
  3264. //#define G0_FEEDRATE 3000 // (mm/min)
  3265. #ifdef G0_FEEDRATE
  3266. //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
  3267. #endif
  3268. /**
  3269. * Startup commands
  3270. *
  3271. * Execute certain G-code commands immediately after power-on.
  3272. */
  3273. //#define STARTUP_COMMANDS "M17 Z"
  3274. /**
  3275. * G-code Macros
  3276. *
  3277. * Add G-codes M810-M819 to define and run G-code macros.
  3278. * Macros are not saved to EEPROM.
  3279. */
  3280. //#define GCODE_MACROS
  3281. #if ENABLED(GCODE_MACROS)
  3282. #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used
  3283. #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro
  3284. #endif
  3285. /**
  3286. * User-defined menu items to run custom G-code.
  3287. * Up to 25 may be defined, but the actual number is LCD-dependent.
  3288. */
  3289. // Custom Menu: Main Menu
  3290. //#define CUSTOM_MENU_MAIN
  3291. #if ENABLED(CUSTOM_MENU_MAIN)
  3292. //#define CUSTOM_MENU_MAIN_TITLE "Custom Commands"
  3293. #define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 User Script Done"
  3294. #define CUSTOM_MENU_MAIN_SCRIPT_AUDIBLE_FEEDBACK
  3295. //#define CUSTOM_MENU_MAIN_SCRIPT_RETURN // Return to status screen after a script
  3296. #define CUSTOM_MENU_MAIN_ONLY_IDLE // Only show custom menu when the machine is idle
  3297. #define MAIN_MENU_ITEM_1_DESC "Home & UBL Info"
  3298. #define MAIN_MENU_ITEM_1_GCODE "G28\nG29 W"
  3299. //#define MAIN_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action
  3300. #define MAIN_MENU_ITEM_2_DESC "Preheat for " PREHEAT_1_LABEL
  3301. #define MAIN_MENU_ITEM_2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  3302. //#define MAIN_MENU_ITEM_2_CONFIRM
  3303. //#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
  3304. //#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  3305. //#define MAIN_MENU_ITEM_3_CONFIRM
  3306. //#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
  3307. //#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  3308. //#define MAIN_MENU_ITEM_4_CONFIRM
  3309. //#define MAIN_MENU_ITEM_5_DESC "Home & Info"
  3310. //#define MAIN_MENU_ITEM_5_GCODE "G28\nM503"
  3311. //#define MAIN_MENU_ITEM_5_CONFIRM
  3312. #endif
  3313. // Custom Menu: Configuration Menu
  3314. //#define CUSTOM_MENU_CONFIG
  3315. #if ENABLED(CUSTOM_MENU_CONFIG)
  3316. //#define CUSTOM_MENU_CONFIG_TITLE "Custom Commands"
  3317. #define CUSTOM_MENU_CONFIG_SCRIPT_DONE "M117 Wireless Script Done"
  3318. #define CUSTOM_MENU_CONFIG_SCRIPT_AUDIBLE_FEEDBACK
  3319. //#define CUSTOM_MENU_CONFIG_SCRIPT_RETURN // Return to status screen after a script
  3320. #define CUSTOM_MENU_CONFIG_ONLY_IDLE // Only show custom menu when the machine is idle
  3321. #define CONFIG_MENU_ITEM_1_DESC "Wifi ON"
  3322. #define CONFIG_MENU_ITEM_1_GCODE "M118 [ESP110] WIFI-STA pwd=12345678"
  3323. //#define CONFIG_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action
  3324. #define CONFIG_MENU_ITEM_2_DESC "Bluetooth ON"
  3325. #define CONFIG_MENU_ITEM_2_GCODE "M118 [ESP110] BT pwd=12345678"
  3326. //#define CONFIG_MENU_ITEM_2_CONFIRM
  3327. //#define CONFIG_MENU_ITEM_3_DESC "Radio OFF"
  3328. //#define CONFIG_MENU_ITEM_3_GCODE "M118 [ESP110] OFF pwd=12345678"
  3329. //#define CONFIG_MENU_ITEM_3_CONFIRM
  3330. //#define CONFIG_MENU_ITEM_4_DESC "Wifi ????"
  3331. //#define CONFIG_MENU_ITEM_4_GCODE "M118 ????"
  3332. //#define CONFIG_MENU_ITEM_4_CONFIRM
  3333. //#define CONFIG_MENU_ITEM_5_DESC "Wifi ????"
  3334. //#define CONFIG_MENU_ITEM_5_GCODE "M118 ????"
  3335. //#define CONFIG_MENU_ITEM_5_CONFIRM
  3336. #endif
  3337. /**
  3338. * User-defined buttons to run custom G-code.
  3339. * Up to 25 may be defined.
  3340. */
  3341. //#define CUSTOM_USER_BUTTONS
  3342. #if ENABLED(CUSTOM_USER_BUTTONS)
  3343. //#define BUTTON1_PIN -1
  3344. #if PIN_EXISTS(BUTTON1)
  3345. #define BUTTON1_HIT_STATE LOW // State of the triggered button. NC=LOW. NO=HIGH.
  3346. #define BUTTON1_WHEN_PRINTING false // Button allowed to trigger during printing?
  3347. #define BUTTON1_GCODE "G28"
  3348. #define BUTTON1_DESC "Homing" // Optional string to set the LCD status
  3349. #endif
  3350. //#define BUTTON2_PIN -1
  3351. #if PIN_EXISTS(BUTTON2)
  3352. #define BUTTON2_HIT_STATE LOW
  3353. #define BUTTON2_WHEN_PRINTING false
  3354. #define BUTTON2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  3355. #define BUTTON2_DESC "Preheat for " PREHEAT_1_LABEL
  3356. #endif
  3357. //#define BUTTON3_PIN -1
  3358. #if PIN_EXISTS(BUTTON3)
  3359. #define BUTTON3_HIT_STATE LOW
  3360. #define BUTTON3_WHEN_PRINTING false
  3361. #define BUTTON3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  3362. #define BUTTON3_DESC "Preheat for " PREHEAT_2_LABEL
  3363. #endif
  3364. #endif
  3365. /**
  3366. * Host Action Commands
  3367. *
  3368. * Define host streamer action commands in compliance with the standard.
  3369. *
  3370. * See https://reprap.org/wiki/G-code#Action_commands
  3371. * Common commands ........ poweroff, pause, paused, resume, resumed, cancel
  3372. * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed
  3373. *
  3374. * Some features add reason codes to extend these commands.
  3375. *
  3376. * Host Prompt Support enables Marlin to use the host for user prompts so
  3377. * filament runout and other processes can be managed from the host side.
  3378. */
  3379. //#define HOST_ACTION_COMMANDS
  3380. #if ENABLED(HOST_ACTION_COMMANDS)
  3381. //#define HOST_PAUSE_M76 // Tell the host to pause in response to M76
  3382. //#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
  3383. #if ENABLED(HOST_PROMPT_SUPPORT)
  3384. //#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications
  3385. #endif
  3386. //#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
  3387. //#define HOST_SHUTDOWN_MENU_ITEM // Add a menu item that tells the host to shut down
  3388. #endif
  3389. /**
  3390. * Cancel Objects
  3391. *
  3392. * Implement M486 to allow Marlin to skip objects
  3393. */
  3394. //#define CANCEL_OBJECTS
  3395. #if ENABLED(CANCEL_OBJECTS)
  3396. #define CANCEL_OBJECTS_REPORTING // Emit the current object as a status message
  3397. #endif
  3398. /**
  3399. * I2C position encoders for closed loop control.
  3400. * Developed by Chris Barr at Aus3D.
  3401. *
  3402. * Wiki: https://wiki.aus3d.com.au/Magnetic_Encoder
  3403. * Github: https://github.com/Aus3D/MagneticEncoder
  3404. *
  3405. * Supplier: https://aus3d.com.au/magnetic-encoder-module
  3406. * Alternative Supplier: https://reliabuild3d.com/
  3407. *
  3408. * Reliabuild encoders have been modified to improve reliability.
  3409. */
  3410. //#define I2C_POSITION_ENCODERS
  3411. #if ENABLED(I2C_POSITION_ENCODERS)
  3412. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  3413. // encoders supported currently.
  3414. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  3415. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  3416. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  3417. // I2CPE_ENC_TYPE_ROTARY.
  3418. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  3419. // 1mm poles. For linear encoders this is ticks / mm,
  3420. // for rotary encoders this is ticks / revolution.
  3421. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  3422. // steps per full revolution (motor steps/rev * microstepping)
  3423. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  3424. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction.
  3425. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  3426. // printer will attempt to correct the error; errors
  3427. // smaller than this are ignored to minimize effects of
  3428. // measurement noise / latency (filter).
  3429. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  3430. #define I2CPE_ENC_2_AXIS Y_AXIS
  3431. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  3432. #define I2CPE_ENC_2_TICKS_UNIT 2048
  3433. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  3434. //#define I2CPE_ENC_2_INVERT
  3435. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP
  3436. #define I2CPE_ENC_2_EC_THRESH 0.10
  3437. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  3438. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  3439. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  3440. #define I2CPE_ENC_4_AXIS E_AXIS
  3441. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  3442. #define I2CPE_ENC_5_AXIS E_AXIS
  3443. // Default settings for encoders which are enabled, but without settings configured above.
  3444. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  3445. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  3446. #define I2CPE_DEF_TICKS_REV (16 * 200)
  3447. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  3448. #define I2CPE_DEF_EC_THRESH 0.1
  3449. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  3450. // axis after which the printer will abort. Comment out to
  3451. // disable abort behavior.
  3452. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  3453. // for this amount of time (in ms) before the encoder
  3454. // is trusted again.
  3455. /**
  3456. * Position is checked every time a new command is executed from the buffer but during long moves,
  3457. * this setting determines the minimum update time between checks. A value of 100 works well with
  3458. * error rolling average when attempting to correct only for skips and not for vibration.
  3459. */
  3460. #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks.
  3461. // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
  3462. #define I2CPE_ERR_ROLLING_AVERAGE
  3463. #endif // I2C_POSITION_ENCODERS
  3464. /**
  3465. * Analog Joystick(s)
  3466. */
  3467. //#define JOYSTICK
  3468. #if ENABLED(JOYSTICK)
  3469. #define JOY_X_PIN 5 // RAMPS: Suggested pin A5 on AUX2
  3470. #define JOY_Y_PIN 10 // RAMPS: Suggested pin A10 on AUX2
  3471. #define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
  3472. #define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
  3473. //#define INVERT_JOY_X // Enable if X direction is reversed
  3474. //#define INVERT_JOY_Y // Enable if Y direction is reversed
  3475. //#define INVERT_JOY_Z // Enable if Z direction is reversed
  3476. // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
  3477. #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
  3478. #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
  3479. #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
  3480. //#define JOYSTICK_DEBUG
  3481. #endif
  3482. /**
  3483. * Mechanical Gantry Calibration
  3484. * Modern replacement for the Prusa TMC_Z_CALIBRATION.
  3485. * Adds capability to work with any adjustable current drivers.
  3486. * Implemented as G34 because M915 is deprecated.
  3487. */
  3488. //#define MECHANICAL_GANTRY_CALIBRATION
  3489. #if ENABLED(MECHANICAL_GANTRY_CALIBRATION)
  3490. #define GANTRY_CALIBRATION_CURRENT 600 // Default calibration current in ma
  3491. #define GANTRY_CALIBRATION_EXTRA_HEIGHT 15 // Extra distance in mm past Z_###_POS to move
  3492. #define GANTRY_CALIBRATION_FEEDRATE 500 // Feedrate for correction move
  3493. //#define GANTRY_CALIBRATION_TO_MIN // Enable to calibrate Z in the MIN direction
  3494. //#define GANTRY_CALIBRATION_SAFE_POSITION XY_CENTER // Safe position for nozzle
  3495. //#define GANTRY_CALIBRATION_XY_PARK_FEEDRATE 3000 // XY Park Feedrate - MMM
  3496. //#define GANTRY_CALIBRATION_COMMANDS_PRE ""
  3497. #define GANTRY_CALIBRATION_COMMANDS_POST "G28" // G28 highly recommended to ensure an accurate position
  3498. #endif
  3499. /**
  3500. * Instant freeze / unfreeze functionality
  3501. * Potentially useful for emergency stop that allows being resumed.
  3502. */
  3503. //#define FREEZE_FEATURE
  3504. #if ENABLED(FREEZE_FEATURE)
  3505. //#define FREEZE_PIN 41 // Override the default (KILL) pin here
  3506. #define FREEZE_STATE LOW // State of pin indicating freeze
  3507. #endif
  3508. /**
  3509. * MAX7219 Debug Matrix
  3510. *
  3511. * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
  3512. * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
  3513. */
  3514. //#define MAX7219_DEBUG
  3515. #if ENABLED(MAX7219_DEBUG)
  3516. #define MAX7219_CLK_PIN 64
  3517. #define MAX7219_DIN_PIN 57
  3518. #define MAX7219_LOAD_PIN 44
  3519. //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix
  3520. #define MAX7219_INIT_TEST 2 // Test pattern at startup: 0=none, 1=sweep, 2=spiral
  3521. #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain.
  3522. #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°)
  3523. // connector at: right=0 bottom=-90 top=90 left=180
  3524. //#define MAX7219_REVERSE_ORDER // The order of the LED matrix units may be reversed
  3525. //#define MAX7219_REVERSE_EACH // The LEDs in each matrix unit row may be reversed
  3526. //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side
  3527. /**
  3528. * Sample debug features
  3529. * If you add more debug displays, be careful to avoid conflicts!
  3530. */
  3531. #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
  3532. #define MAX7219_DEBUG_PLANNER_HEAD 2 // Show the planner queue head position on this and the next LED matrix row
  3533. #define MAX7219_DEBUG_PLANNER_TAIL 4 // Show the planner queue tail position on this and the next LED matrix row
  3534. #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row
  3535. // If you experience stuttering, reboots, etc. this option can reveal how
  3536. // tweaks made to the configuration are affecting the printer in real-time.
  3537. #define MAX7219_DEBUG_PROFILE 6 // Display the fraction of CPU time spent in profiled code on this LED matrix
  3538. // row. By default idle() is profiled so this shows how "idle" the processor is.
  3539. // See class CodeProfiler.
  3540. #endif
  3541. /**
  3542. * NanoDLP Sync support
  3543. *
  3544. * Support for Synchronized Z moves when used with NanoDLP. G0/G1 axis moves will
  3545. * output a "Z_move_comp" string to enable synchronization with DLP projector exposure.
  3546. * This feature allows you to use [[WaitForDoneMessage]] instead of M400 commands.
  3547. */
  3548. //#define NANODLP_Z_SYNC
  3549. #if ENABLED(NANODLP_Z_SYNC)
  3550. //#define NANODLP_ALL_AXIS // Send a "Z_move_comp" report for any axis move (not just Z).
  3551. #endif
  3552. /**
  3553. * Ethernet. Use M552 to enable and set the IP address.
  3554. */
  3555. #if HAS_ETHERNET
  3556. #define MAC_ADDRESS { 0xDE, 0xAD, 0xBE, 0xEF, 0xF0, 0x0D } // A MAC address unique to your network
  3557. #endif
  3558. /**
  3559. * WiFi Support (Espressif ESP32 WiFi)
  3560. */
  3561. //#define WIFISUPPORT // Marlin embedded WiFi managenent
  3562. //#define ESP3D_WIFISUPPORT // ESP3D Library WiFi management (https://github.com/luc-github/ESP3DLib)
  3563. #if EITHER(WIFISUPPORT, ESP3D_WIFISUPPORT)
  3564. //#define WEBSUPPORT // Start a webserver (which may include auto-discovery)
  3565. //#define OTASUPPORT // Support over-the-air firmware updates
  3566. //#define WIFI_CUSTOM_COMMAND // Accept feature config commands (e.g., WiFi ESP3D) from the host
  3567. /**
  3568. * To set a default WiFi SSID / Password, create a file called Configuration_Secure.h with
  3569. * the following defines, customized for your network. This specific file is excluded via
  3570. * .gitignore to prevent it from accidentally leaking to the public.
  3571. *
  3572. * #define WIFI_SSID "WiFi SSID"
  3573. * #define WIFI_PWD "WiFi Password"
  3574. */
  3575. //#include "Configuration_Secure.h" // External file with WiFi SSID / Password
  3576. #endif
  3577. /**
  3578. * Průša Multi-Material Unit (MMU)
  3579. * Enable in Configuration.h
  3580. *
  3581. * These devices allow a single stepper driver on the board to drive
  3582. * multi-material feeders with any number of stepper motors.
  3583. */
  3584. #if HAS_PRUSA_MMU1
  3585. /**
  3586. * This option only allows the multiplexer to switch on tool-change.
  3587. * Additional options to configure custom E moves are pending.
  3588. *
  3589. * Override the default DIO selector pins here, if needed.
  3590. * Some pins files may provide defaults for these pins.
  3591. */
  3592. //#define E_MUX0_PIN 40 // Always Required
  3593. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  3594. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  3595. #elif HAS_PRUSA_MMU2
  3596. // Serial port used for communication with MMU2.
  3597. #define MMU2_SERIAL_PORT 2
  3598. // Use hardware reset for MMU if a pin is defined for it
  3599. //#define MMU2_RST_PIN 23
  3600. // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up)
  3601. //#define MMU2_MODE_12V
  3602. // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout
  3603. #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600"
  3604. // Add an LCD menu for MMU2
  3605. //#define MMU2_MENUS
  3606. #if EITHER(MMU2_MENUS, HAS_PRUSA_MMU2S)
  3607. // Settings for filament load / unload from the LCD menu.
  3608. // This is for Průša MK3-style extruders. Customize for your hardware.
  3609. #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0
  3610. #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \
  3611. { 7.2, 1145 }, \
  3612. { 14.4, 871 }, \
  3613. { 36.0, 1393 }, \
  3614. { 14.4, 871 }, \
  3615. { 50.0, 198 }
  3616. #define MMU2_RAMMING_SEQUENCE \
  3617. { 1.0, 1000 }, \
  3618. { 1.0, 1500 }, \
  3619. { 2.0, 2000 }, \
  3620. { 1.5, 3000 }, \
  3621. { 2.5, 4000 }, \
  3622. { -15.0, 5000 }, \
  3623. { -14.0, 1200 }, \
  3624. { -6.0, 600 }, \
  3625. { 10.0, 700 }, \
  3626. { -10.0, 400 }, \
  3627. { -50.0, 2000 }
  3628. #endif
  3629. /**
  3630. * Using a sensor like the MMU2S
  3631. * This mode requires a MK3S extruder with a sensor at the extruder idler, like the MMU2S.
  3632. * See https://help.prusa3d.com/en/guide/3b-mk3s-mk2-5s-extruder-upgrade_41560, step 11
  3633. */
  3634. #if HAS_PRUSA_MMU2S
  3635. #define MMU2_C0_RETRY 5 // Number of retries (total time = timeout*retries)
  3636. #define MMU2_CAN_LOAD_FEEDRATE 800 // (mm/min)
  3637. #define MMU2_CAN_LOAD_SEQUENCE \
  3638. { 0.1, MMU2_CAN_LOAD_FEEDRATE }, \
  3639. { 60.0, MMU2_CAN_LOAD_FEEDRATE }, \
  3640. { -52.0, MMU2_CAN_LOAD_FEEDRATE }
  3641. #define MMU2_CAN_LOAD_RETRACT 6.0 // (mm) Keep under the distance between Load Sequence values
  3642. #define MMU2_CAN_LOAD_DEVIATION 0.8 // (mm) Acceptable deviation
  3643. #define MMU2_CAN_LOAD_INCREMENT 0.2 // (mm) To reuse within MMU2 module
  3644. #define MMU2_CAN_LOAD_INCREMENT_SEQUENCE \
  3645. { -MMU2_CAN_LOAD_INCREMENT, MMU2_CAN_LOAD_FEEDRATE }
  3646. #else
  3647. /**
  3648. * MMU1 Extruder Sensor
  3649. *
  3650. * Support for a Průša (or other) IR Sensor to detect filament near the extruder
  3651. * and make loading more reliable. Suitable for an extruder equipped with a filament
  3652. * sensor less than 38mm from the gears.
  3653. *
  3654. * During loading the extruder will stop when the sensor is triggered, then do a last
  3655. * move up to the gears. If no filament is detected, the MMU2 can make some more attempts.
  3656. * If all attempts fail, a filament runout will be triggered.
  3657. */
  3658. //#define MMU_EXTRUDER_SENSOR
  3659. #if ENABLED(MMU_EXTRUDER_SENSOR)
  3660. #define MMU_LOADING_ATTEMPTS_NR 5 // max. number of attempts to load filament if first load fail
  3661. #endif
  3662. #endif
  3663. //#define MMU2_DEBUG // Write debug info to serial output
  3664. #endif // HAS_PRUSA_MMU2
  3665. /**
  3666. * Advanced Print Counter settings
  3667. */
  3668. #if ENABLED(PRINTCOUNTER)
  3669. #define SERVICE_WARNING_BUZZES 3
  3670. // Activate up to 3 service interval watchdogs
  3671. //#define SERVICE_NAME_1 "Service S"
  3672. //#define SERVICE_INTERVAL_1 100 // print hours
  3673. //#define SERVICE_NAME_2 "Service L"
  3674. //#define SERVICE_INTERVAL_2 200 // print hours
  3675. //#define SERVICE_NAME_3 "Service 3"
  3676. //#define SERVICE_INTERVAL_3 1 // print hours
  3677. #endif
  3678. // @section develop
  3679. //
  3680. // M100 Free Memory Watcher to debug memory usage
  3681. //
  3682. //#define M100_FREE_MEMORY_WATCHER
  3683. //
  3684. // M42 - Set pin states
  3685. //
  3686. //#define DIRECT_PIN_CONTROL
  3687. //
  3688. // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
  3689. //
  3690. //#define PINS_DEBUGGING
  3691. // Enable Marlin dev mode which adds some special commands
  3692. //#define MARLIN_DEV_MODE
  3693. #if ENABLED(MARLIN_DEV_MODE)
  3694. /**
  3695. * D576 - Buffer Monitoring
  3696. * To help diagnose print quality issues stemming from empty command buffers.
  3697. */
  3698. //#define BUFFER_MONITORING
  3699. #endif
  3700. /**
  3701. * Postmortem Debugging captures misbehavior and outputs the CPU status and backtrace to serial.
  3702. * When running in the debugger it will break for debugging. This is useful to help understand
  3703. * a crash from a remote location. Requires ~400 bytes of SRAM and 5Kb of flash.
  3704. */
  3705. //#define POSTMORTEM_DEBUGGING
  3706. /**
  3707. * Software Reset options
  3708. */
  3709. //#define SOFT_RESET_VIA_SERIAL // 'KILL' and '^X' commands will soft-reset the controller
  3710. //#define SOFT_RESET_ON_KILL // Use a digital button to soft-reset the controller after KILL
  3711. // Report uncleaned reset reason from register r2 instead of MCUSR. Supported by Optiboot on AVR.
  3712. //#define OPTIBOOT_RESET_REASON