My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration_adv.h 178KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720172117221723172417251726172717281729173017311732173317341735173617371738173917401741174217431744174517461747174817491750175117521753175417551756175717581759176017611762176317641765176617671768176917701771177217731774177517761777177817791780178117821783178417851786178717881789179017911792179317941795179617971798179918001801180218031804180518061807180818091810181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391840184118421843184418451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906190719081909191019111912191319141915191619171918191919201921192219231924192519261927192819291930193119321933193419351936193719381939194019411942194319441945194619471948194919501951195219531954195519561957195819591960196119621963196419651966196719681969197019711972197319741975197619771978197919801981198219831984198519861987198819891990199119921993199419951996199719981999200020012002200320042005200620072008200920102011201220132014201520162017201820192020202120222023202420252026202720282029203020312032203320342035203620372038203920402041204220432044204520462047204820492050205120522053205420552056205720582059206020612062206320642065206620672068206920702071207220732074207520762077207820792080208120822083208420852086208720882089209020912092209320942095209620972098209921002101210221032104210521062107210821092110211121122113211421152116211721182119212021212122212321242125212621272128212921302131213221332134213521362137213821392140214121422143214421452146214721482149215021512152215321542155215621572158215921602161216221632164216521662167216821692170217121722173217421752176217721782179218021812182218321842185218621872188218921902191219221932194219521962197219821992200220122022203220422052206220722082209221022112212221322142215221622172218221922202221222222232224222522262227222822292230223122322233223422352236223722382239224022412242224322442245224622472248224922502251225222532254225522562257225822592260226122622263226422652266226722682269227022712272227322742275227622772278227922802281228222832284228522862287228822892290229122922293229422952296229722982299230023012302230323042305230623072308230923102311231223132314231523162317231823192320232123222323232423252326232723282329233023312332233323342335233623372338233923402341234223432344234523462347234823492350235123522353235423552356235723582359236023612362236323642365236623672368236923702371237223732374237523762377237823792380238123822383238423852386238723882389239023912392239323942395239623972398239924002401240224032404240524062407240824092410241124122413241424152416241724182419242024212422242324242425242624272428242924302431243224332434243524362437243824392440244124422443244424452446244724482449245024512452245324542455245624572458245924602461246224632464246524662467246824692470247124722473247424752476247724782479248024812482248324842485248624872488248924902491249224932494249524962497249824992500250125022503250425052506250725082509251025112512251325142515251625172518251925202521252225232524252525262527252825292530253125322533253425352536253725382539254025412542254325442545254625472548254925502551255225532554255525562557255825592560256125622563256425652566256725682569257025712572257325742575257625772578257925802581258225832584258525862587258825892590259125922593259425952596259725982599260026012602260326042605260626072608260926102611261226132614261526162617261826192620262126222623262426252626262726282629263026312632263326342635263626372638263926402641264226432644264526462647264826492650265126522653265426552656265726582659266026612662266326642665266626672668266926702671267226732674267526762677267826792680268126822683268426852686268726882689269026912692269326942695269626972698269927002701270227032704270527062707270827092710271127122713271427152716271727182719272027212722272327242725272627272728272927302731273227332734273527362737273827392740274127422743274427452746274727482749275027512752275327542755275627572758275927602761276227632764276527662767276827692770277127722773277427752776277727782779278027812782278327842785278627872788278927902791279227932794279527962797279827992800280128022803280428052806280728082809281028112812281328142815281628172818281928202821282228232824282528262827282828292830283128322833283428352836283728382839284028412842284328442845284628472848284928502851285228532854285528562857285828592860286128622863286428652866286728682869287028712872287328742875287628772878287928802881288228832884288528862887288828892890289128922893289428952896289728982899290029012902290329042905290629072908290929102911291229132914291529162917291829192920292129222923292429252926292729282929293029312932293329342935293629372938293929402941294229432944294529462947294829492950295129522953295429552956295729582959296029612962296329642965296629672968296929702971297229732974297529762977297829792980298129822983298429852986298729882989299029912992299329942995299629972998299930003001300230033004300530063007300830093010301130123013301430153016301730183019302030213022302330243025302630273028302930303031303230333034303530363037303830393040304130423043304430453046304730483049305030513052305330543055305630573058305930603061306230633064306530663067306830693070307130723073307430753076307730783079308030813082308330843085308630873088308930903091309230933094309530963097309830993100310131023103310431053106310731083109311031113112311331143115311631173118311931203121312231233124312531263127312831293130313131323133313431353136313731383139314031413142314331443145314631473148314931503151315231533154315531563157315831593160316131623163316431653166316731683169317031713172317331743175317631773178317931803181318231833184318531863187318831893190319131923193319431953196319731983199320032013202320332043205320632073208320932103211321232133214321532163217321832193220322132223223322432253226322732283229323032313232323332343235323632373238323932403241324232433244324532463247324832493250325132523253325432553256325732583259326032613262326332643265326632673268326932703271327232733274327532763277327832793280328132823283328432853286328732883289329032913292329332943295329632973298329933003301330233033304330533063307330833093310331133123313331433153316331733183319332033213322332333243325332633273328332933303331333233333334333533363337333833393340334133423343334433453346334733483349335033513352335333543355335633573358335933603361336233633364336533663367336833693370337133723373337433753376337733783379338033813382338333843385338633873388338933903391339233933394339533963397339833993400340134023403340434053406340734083409341034113412341334143415341634173418341934203421342234233424342534263427342834293430343134323433343434353436343734383439344034413442344334443445344634473448344934503451345234533454345534563457345834593460346134623463346434653466346734683469347034713472347334743475347634773478347934803481348234833484348534863487348834893490349134923493349434953496349734983499350035013502350335043505350635073508350935103511351235133514351535163517351835193520352135223523352435253526352735283529353035313532353335343535353635373538353935403541354235433544354535463547354835493550355135523553355435553556355735583559356035613562356335643565356635673568356935703571357235733574357535763577357835793580358135823583358435853586358735883589359035913592359335943595359635973598359936003601360236033604360536063607360836093610361136123613361436153616361736183619362036213622362336243625362636273628362936303631363236333634363536363637363836393640364136423643364436453646364736483649365036513652365336543655365636573658365936603661366236633664366536663667366836693670367136723673367436753676367736783679368036813682368336843685368636873688368936903691369236933694369536963697369836993700370137023703370437053706370737083709371037113712371337143715371637173718371937203721372237233724372537263727372837293730373137323733373437353736373737383739374037413742374337443745374637473748374937503751375237533754375537563757375837593760376137623763376437653766376737683769377037713772377337743775377637773778377937803781378237833784378537863787378837893790379137923793379437953796379737983799380038013802380338043805380638073808380938103811381238133814381538163817381838193820382138223823382438253826382738283829383038313832383338343835383638373838383938403841384238433844384538463847384838493850385138523853385438553856385738583859386038613862386338643865386638673868386938703871387238733874387538763877387838793880388138823883388438853886388738883889389038913892389338943895389638973898389939003901390239033904390539063907390839093910391139123913391439153916391739183919392039213922392339243925392639273928392939303931393239333934393539363937393839393940394139423943394439453946394739483949395039513952395339543955395639573958395939603961396239633964396539663967396839693970397139723973397439753976397739783979398039813982398339843985398639873988398939903991399239933994399539963997399839994000400140024003400440054006400740084009401040114012401340144015401640174018401940204021402240234024402540264027402840294030403140324033403440354036403740384039404040414042404340444045404640474048404940504051405240534054405540564057405840594060406140624063406440654066406740684069407040714072407340744075407640774078407940804081408240834084408540864087408840894090409140924093409440954096409740984099410041014102410341044105410641074108410941104111411241134114411541164117411841194120412141224123412441254126412741284129413041314132413341344135413641374138413941404141414241434144414541464147414841494150415141524153415441554156415741584159416041614162416341644165416641674168416941704171417241734174417541764177417841794180418141824183418441854186418741884189419041914192419341944195419641974198419942004201420242034204420542064207420842094210421142124213421442154216421742184219422042214222422342244225422642274228422942304231423242334234423542364237423842394240424142424243424442454246424742484249425042514252425342544255425642574258425942604261426242634264426542664267426842694270427142724273427442754276427742784279428042814282428342844285428642874288428942904291429242934294429542964297429842994300430143024303430443054306430743084309431043114312431343144315431643174318431943204321432243234324432543264327432843294330433143324333433443354336433743384339434043414342434343444345434643474348434943504351435243534354435543564357435843594360436143624363436443654366436743684369437043714372437343744375437643774378437943804381438243834384438543864387438843894390439143924393439443954396439743984399440044014402440344044405440644074408440944104411441244134414441544164417441844194420442144224423442444254426442744284429443044314432443344344435443644374438443944404441444244434444444544464447444844494450445144524453445444554456445744584459446044614462446344644465446644674468446944704471447244734474447544764477
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration_adv.h
  25. *
  26. * Advanced settings.
  27. * Only change these if you know exactly what you're doing.
  28. * Some of these settings can damage your printer if improperly set!
  29. *
  30. * Basic settings can be found in Configuration.h
  31. */
  32. #define CONFIGURATION_ADV_H_VERSION 02010100
  33. //===========================================================================
  34. //============================= Thermal Settings ============================
  35. //===========================================================================
  36. // @section temperature
  37. /**
  38. * Thermocouple sensors are quite sensitive to noise. Any noise induced in
  39. * the sensor wires, such as by stepper motor wires run in parallel to them,
  40. * may result in the thermocouple sensor reporting spurious errors. This
  41. * value is the number of errors which can occur in a row before the error
  42. * is reported. This allows us to ignore intermittent error conditions while
  43. * still detecting an actual failure, which should result in a continuous
  44. * stream of errors from the sensor.
  45. *
  46. * Set this value to 0 to fail on the first error to occur.
  47. */
  48. #define THERMOCOUPLE_MAX_ERRORS 15
  49. //
  50. // Custom Thermistor 1000 parameters
  51. //
  52. #if TEMP_SENSOR_0 == 1000
  53. #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  54. #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  55. #define HOTEND0_BETA 3950 // Beta value
  56. #endif
  57. #if TEMP_SENSOR_1 == 1000
  58. #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  59. #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  60. #define HOTEND1_BETA 3950 // Beta value
  61. #endif
  62. #if TEMP_SENSOR_2 == 1000
  63. #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  64. #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  65. #define HOTEND2_BETA 3950 // Beta value
  66. #endif
  67. #if TEMP_SENSOR_3 == 1000
  68. #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  69. #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  70. #define HOTEND3_BETA 3950 // Beta value
  71. #endif
  72. #if TEMP_SENSOR_4 == 1000
  73. #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  74. #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  75. #define HOTEND4_BETA 3950 // Beta value
  76. #endif
  77. #if TEMP_SENSOR_5 == 1000
  78. #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  79. #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  80. #define HOTEND5_BETA 3950 // Beta value
  81. #endif
  82. #if TEMP_SENSOR_6 == 1000
  83. #define HOTEND6_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  84. #define HOTEND6_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  85. #define HOTEND6_BETA 3950 // Beta value
  86. #endif
  87. #if TEMP_SENSOR_7 == 1000
  88. #define HOTEND7_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  89. #define HOTEND7_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  90. #define HOTEND7_BETA 3950 // Beta value
  91. #endif
  92. #if TEMP_SENSOR_BED == 1000
  93. #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  94. #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  95. #define BED_BETA 3950 // Beta value
  96. #endif
  97. #if TEMP_SENSOR_CHAMBER == 1000
  98. #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  99. #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  100. #define CHAMBER_BETA 3950 // Beta value
  101. #endif
  102. #if TEMP_SENSOR_COOLER == 1000
  103. #define COOLER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  104. #define COOLER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  105. #define COOLER_BETA 3950 // Beta value
  106. #endif
  107. #if TEMP_SENSOR_PROBE == 1000
  108. #define PROBE_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  109. #define PROBE_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  110. #define PROBE_BETA 3950 // Beta value
  111. #endif
  112. #if TEMP_SENSOR_BOARD == 1000
  113. #define BOARD_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  114. #define BOARD_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  115. #define BOARD_BETA 3950 // Beta value
  116. #endif
  117. #if TEMP_SENSOR_REDUNDANT == 1000
  118. #define REDUNDANT_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  119. #define REDUNDANT_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  120. #define REDUNDANT_BETA 3950 // Beta value
  121. #endif
  122. /**
  123. * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5).
  124. */
  125. //#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus.
  126. //#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board.
  127. //#define MAX31865_SENSOR_WIRES_1 2
  128. //#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz.
  129. //#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors.
  130. //#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature.
  131. //#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals.
  132. //#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439).
  133. //#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings.
  134. //#define MAX31865_WIRE_OHMS_1 0.0f
  135. /**
  136. * Hephestos 2 24V heated bed upgrade kit.
  137. * https://store.bq.com/en/heated-bed-kit-hephestos2
  138. */
  139. //#define HEPHESTOS2_HEATED_BED_KIT
  140. #if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
  141. #undef TEMP_SENSOR_BED
  142. #define TEMP_SENSOR_BED 70
  143. #define HEATER_BED_INVERTING true
  144. #endif
  145. //
  146. // Heated Bed Bang-Bang options
  147. //
  148. #if DISABLED(PIDTEMPBED)
  149. #define BED_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
  150. #if ENABLED(BED_LIMIT_SWITCHING)
  151. #define BED_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > BED_HYSTERESIS
  152. #endif
  153. #endif
  154. //
  155. // Heated Chamber options
  156. //
  157. #if DISABLED(PIDTEMPCHAMBER)
  158. #define CHAMBER_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
  159. #if ENABLED(CHAMBER_LIMIT_SWITCHING)
  160. #define CHAMBER_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > CHAMBER_HYSTERESIS
  161. #endif
  162. #endif
  163. #if TEMP_SENSOR_CHAMBER
  164. //#define HEATER_CHAMBER_PIN P2_04 // Required heater on/off pin (example: SKR 1.4 Turbo HE1 plug)
  165. //#define HEATER_CHAMBER_INVERTING false
  166. //#define FAN1_PIN -1 // Remove the fan signal on pin P2_04 (example: SKR 1.4 Turbo HE1 plug)
  167. //#define CHAMBER_FAN // Enable a fan on the chamber
  168. #if ENABLED(CHAMBER_FAN)
  169. //#define CHAMBER_FAN_INDEX 2 // Index of a fan to repurpose as the chamber fan. (Default: first unused fan)
  170. #define CHAMBER_FAN_MODE 2 // Fan control mode: 0=Static; 1=Linear increase when temp is higher than target; 2=V-shaped curve; 3=similar to 1 but fan is always on.
  171. #if CHAMBER_FAN_MODE == 0
  172. #define CHAMBER_FAN_BASE 255 // Chamber fan PWM (0-255)
  173. #elif CHAMBER_FAN_MODE == 1
  174. #define CHAMBER_FAN_BASE 128 // Base chamber fan PWM (0-255); turns on when chamber temperature is above the target
  175. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C above target
  176. #elif CHAMBER_FAN_MODE == 2
  177. #define CHAMBER_FAN_BASE 128 // Minimum chamber fan PWM (0-255)
  178. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C difference from target
  179. #elif CHAMBER_FAN_MODE == 3
  180. #define CHAMBER_FAN_BASE 128 // Base chamber fan PWM (0-255)
  181. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C above target
  182. #endif
  183. #endif
  184. //#define CHAMBER_VENT // Enable a servo-controlled vent on the chamber
  185. #if ENABLED(CHAMBER_VENT)
  186. #define CHAMBER_VENT_SERVO_NR 1 // Index of the vent servo
  187. #define HIGH_EXCESS_HEAT_LIMIT 5 // How much above target temp to consider there is excess heat in the chamber
  188. #define LOW_EXCESS_HEAT_LIMIT 3
  189. #define MIN_COOLING_SLOPE_TIME_CHAMBER_VENT 20
  190. #define MIN_COOLING_SLOPE_DEG_CHAMBER_VENT 1.5
  191. #endif
  192. #endif
  193. //
  194. // Laser Cooler options
  195. //
  196. #if TEMP_SENSOR_COOLER
  197. #define COOLER_MINTEMP 8 // (°C)
  198. #define COOLER_MAXTEMP 26 // (°C)
  199. #define COOLER_DEFAULT_TEMP 16 // (°C)
  200. #define TEMP_COOLER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
  201. #define COOLER_PIN 8 // Laser cooler on/off pin used to control power to the cooling element (e.g., TEC, External chiller via relay)
  202. #define COOLER_INVERTING false
  203. #define TEMP_COOLER_PIN 15 // Laser/Cooler temperature sensor pin. ADC is required.
  204. #define COOLER_FAN // Enable a fan on the cooler, Fan# 0,1,2,3 etc.
  205. #define COOLER_FAN_INDEX 0 // FAN number 0, 1, 2 etc. e.g.
  206. #if ENABLED(COOLER_FAN)
  207. #define COOLER_FAN_BASE 100 // Base Cooler fan PWM (0-255); turns on when Cooler temperature is above the target
  208. #define COOLER_FAN_FACTOR 25 // PWM increase per °C above target
  209. #endif
  210. #endif
  211. //
  212. // Motherboard Sensor options
  213. //
  214. #if TEMP_SENSOR_BOARD
  215. #define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
  216. #define BOARD_MINTEMP 8 // (°C)
  217. #define BOARD_MAXTEMP 70 // (°C)
  218. #ifndef TEMP_BOARD_PIN
  219. //#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
  220. #endif
  221. #endif
  222. /**
  223. * Thermal Protection provides additional protection to your printer from damage
  224. * and fire. Marlin always includes safe min and max temperature ranges which
  225. * protect against a broken or disconnected thermistor wire.
  226. *
  227. * The issue: If a thermistor falls out, it will report the much lower
  228. * temperature of the air in the room, and the the firmware will keep
  229. * the heater on.
  230. *
  231. * The solution: Once the temperature reaches the target, start observing.
  232. * If the temperature stays too far below the target (hysteresis) for too
  233. * long (period), the firmware will halt the machine as a safety precaution.
  234. *
  235. * If you get false positives for "Thermal Runaway", increase
  236. * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  237. */
  238. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  239. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  240. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  241. //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
  242. #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
  243. //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
  244. #endif
  245. /**
  246. * Whenever an M104, M109, or M303 increases the target temperature, the
  247. * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
  248. * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
  249. * requires a hard reset. This test restarts with any M104/M109/M303, but only
  250. * if the current temperature is far enough below the target for a reliable
  251. * test.
  252. *
  253. * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
  254. * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
  255. * below 2.
  256. */
  257. #define WATCH_TEMP_PERIOD 20 // Seconds
  258. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  259. #endif
  260. /**
  261. * Thermal Protection parameters for the bed are just as above for hotends.
  262. */
  263. #if ENABLED(THERMAL_PROTECTION_BED)
  264. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  265. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  266. /**
  267. * As described above, except for the bed (M140/M190/M303).
  268. */
  269. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  270. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  271. #endif
  272. /**
  273. * Thermal Protection parameters for the heated chamber.
  274. */
  275. #if ENABLED(THERMAL_PROTECTION_CHAMBER)
  276. #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
  277. #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
  278. /**
  279. * Heated chamber watch settings (M141/M191).
  280. */
  281. #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
  282. #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
  283. #endif
  284. /**
  285. * Thermal Protection parameters for the laser cooler.
  286. */
  287. #if ENABLED(THERMAL_PROTECTION_COOLER)
  288. #define THERMAL_PROTECTION_COOLER_PERIOD 10 // Seconds
  289. #define THERMAL_PROTECTION_COOLER_HYSTERESIS 3 // Degrees Celsius
  290. /**
  291. * Laser cooling watch settings (M143/M193).
  292. */
  293. #define WATCH_COOLER_TEMP_PERIOD 60 // Seconds
  294. #define WATCH_COOLER_TEMP_INCREASE 3 // Degrees Celsius
  295. #endif
  296. #if ANY(THERMAL_PROTECTION_HOTENDS, THERMAL_PROTECTION_BED, THERMAL_PROTECTION_CHAMBER, THERMAL_PROTECTION_COOLER)
  297. /**
  298. * Thermal Protection Variance Monitor - EXPERIMENTAL.
  299. * Kill the machine on a stuck temperature sensor. Disable if you get false positives.
  300. */
  301. //#define THERMAL_PROTECTION_VARIANCE_MONITOR // Detect a sensor malfunction preventing temperature updates
  302. #endif
  303. #if ENABLED(PIDTEMP)
  304. // Add an experimental additional term to the heater power, proportional to the extrusion speed.
  305. // A well-chosen Kc value should add just enough power to melt the increased material volume.
  306. //#define PID_EXTRUSION_SCALING
  307. #if ENABLED(PID_EXTRUSION_SCALING)
  308. #define DEFAULT_Kc (100) // heating power = Kc * e_speed
  309. #define LPQ_MAX_LEN 50
  310. #endif
  311. /**
  312. * Add an experimental additional term to the heater power, proportional to the fan speed.
  313. * A well-chosen Kf value should add just enough power to compensate for power-loss from the cooling fan.
  314. * You can either just add a constant compensation with the DEFAULT_Kf value
  315. * or follow the instruction below to get speed-dependent compensation.
  316. *
  317. * Constant compensation (use only with fanspeeds of 0% and 100%)
  318. * ---------------------------------------------------------------------
  319. * A good starting point for the Kf-value comes from the calculation:
  320. * kf = (power_fan * eff_fan) / power_heater * 255
  321. * where eff_fan is between 0.0 and 1.0, based on fan-efficiency and airflow to the nozzle / heater.
  322. *
  323. * Example:
  324. * Heater: 40W, Fan: 0.1A * 24V = 2.4W, eff_fan = 0.8
  325. * Kf = (2.4W * 0.8) / 40W * 255 = 12.24
  326. *
  327. * Fan-speed dependent compensation
  328. * --------------------------------
  329. * 1. To find a good Kf value, set the hotend temperature, wait for it to settle, and enable the fan (100%).
  330. * Make sure PID_FAN_SCALING_LIN_FACTOR is 0 and PID_FAN_SCALING_ALTERNATIVE_DEFINITION is not enabled.
  331. * If you see the temperature drop repeat the test, increasing the Kf value slowly, until the temperature
  332. * drop goes away. If the temperature overshoots after enabling the fan, the Kf value is too big.
  333. * 2. Note the Kf-value for fan-speed at 100%
  334. * 3. Determine a good value for PID_FAN_SCALING_MIN_SPEED, which is around the speed, where the fan starts moving.
  335. * 4. Repeat step 1. and 2. for this fan speed.
  336. * 5. Enable PID_FAN_SCALING_ALTERNATIVE_DEFINITION and enter the two identified Kf-values in
  337. * PID_FAN_SCALING_AT_FULL_SPEED and PID_FAN_SCALING_AT_MIN_SPEED. Enter the minimum speed in PID_FAN_SCALING_MIN_SPEED
  338. */
  339. //#define PID_FAN_SCALING
  340. #if ENABLED(PID_FAN_SCALING)
  341. //#define PID_FAN_SCALING_ALTERNATIVE_DEFINITION
  342. #if ENABLED(PID_FAN_SCALING_ALTERNATIVE_DEFINITION)
  343. // The alternative definition is used for an easier configuration.
  344. // Just figure out Kf at fullspeed (255) and PID_FAN_SCALING_MIN_SPEED.
  345. // DEFAULT_Kf and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.
  346. #define PID_FAN_SCALING_AT_FULL_SPEED 13.0 //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_Kf
  347. #define PID_FAN_SCALING_AT_MIN_SPEED 6.0 //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
  348. #define PID_FAN_SCALING_MIN_SPEED 10.0 // Minimum fan speed at which to enable PID_FAN_SCALING
  349. #define DEFAULT_Kf (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
  350. #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_Kf)/255.0
  351. #else
  352. #define PID_FAN_SCALING_LIN_FACTOR (0) // Power loss due to cooling = Kf * (fan_speed)
  353. #define DEFAULT_Kf 10 // A constant value added to the PID-tuner
  354. #define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
  355. #endif
  356. #endif
  357. #endif
  358. /**
  359. * Automatic Temperature Mode
  360. *
  361. * Dynamically adjust the hotend target temperature based on planned E moves.
  362. *
  363. * (Contrast with PID_EXTRUSION_SCALING, which tracks E movement and adjusts PID
  364. * behavior using an additional kC value.)
  365. *
  366. * Autotemp is calculated by (mintemp + factor * mm_per_sec), capped to maxtemp.
  367. *
  368. * Enable Autotemp Mode with M104/M109 F<factor> S<mintemp> B<maxtemp>.
  369. * Disable by sending M104/M109 with no F parameter (or F0 with AUTOTEMP_PROPORTIONAL).
  370. */
  371. #define AUTOTEMP
  372. #if ENABLED(AUTOTEMP)
  373. #define AUTOTEMP_OLDWEIGHT 0.98 // Factor used to weight previous readings (0.0 < value < 1.0)
  374. // Turn on AUTOTEMP on M104/M109 by default using proportions set here
  375. //#define AUTOTEMP_PROPORTIONAL
  376. #if ENABLED(AUTOTEMP_PROPORTIONAL)
  377. #define AUTOTEMP_MIN_P 0 // (°C) Added to the target temperature
  378. #define AUTOTEMP_MAX_P 5 // (°C) Added to the target temperature
  379. #define AUTOTEMP_FACTOR_P 1 // Apply this F parameter by default (overridden by M104/M109 F)
  380. #endif
  381. #endif
  382. // Show Temperature ADC value
  383. // Enable for M105 to include ADC values read from temperature sensors.
  384. //#define SHOW_TEMP_ADC_VALUES
  385. /**
  386. * High Temperature Thermistor Support
  387. *
  388. * Thermistors able to support high temperature tend to have a hard time getting
  389. * good readings at room and lower temperatures. This means TEMP_SENSOR_X_RAW_LO_TEMP
  390. * will probably be caught when the heating element first turns on during the
  391. * preheating process, which will trigger a min_temp_error as a safety measure
  392. * and force stop everything.
  393. * To circumvent this limitation, we allow for a preheat time (during which,
  394. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  395. * aberrant readings.
  396. *
  397. * If you want to enable this feature for your hotend thermistor(s)
  398. * uncomment and set values > 0 in the constants below
  399. */
  400. // The number of consecutive low temperature errors that can occur
  401. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  402. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  403. // The number of milliseconds a hotend will preheat before starting to check
  404. // the temperature. This value should NOT be set to the time it takes the
  405. // hot end to reach the target temperature, but the time it takes to reach
  406. // the minimum temperature your thermistor can read. The lower the better/safer.
  407. // This shouldn't need to be more than 30 seconds (30000)
  408. //#define MILLISECONDS_PREHEAT_TIME 0
  409. // @section extruder
  410. // Extruder runout prevention.
  411. // If the machine is idle and the temperature over MINTEMP
  412. // then extrude some filament every couple of SECONDS.
  413. //#define EXTRUDER_RUNOUT_PREVENT
  414. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  415. #define EXTRUDER_RUNOUT_MINTEMP 190
  416. #define EXTRUDER_RUNOUT_SECONDS 30
  417. #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/min)
  418. #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm)
  419. #endif
  420. /**
  421. * Hotend Idle Timeout
  422. * Prevent filament in the nozzle from charring and causing a critical jam.
  423. */
  424. //#define HOTEND_IDLE_TIMEOUT
  425. #if ENABLED(HOTEND_IDLE_TIMEOUT)
  426. #define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection
  427. #define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
  428. #define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
  429. #define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
  430. #endif
  431. // @section temperature
  432. // Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
  433. // The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
  434. #define TEMP_SENSOR_AD595_OFFSET 0.0
  435. #define TEMP_SENSOR_AD595_GAIN 1.0
  436. #define TEMP_SENSOR_AD8495_OFFSET 0.0
  437. #define TEMP_SENSOR_AD8495_GAIN 1.0
  438. /**
  439. * Controller Fan
  440. * To cool down the stepper drivers and MOSFETs.
  441. *
  442. * The fan turns on automatically whenever any driver is enabled and turns
  443. * off (or reduces to idle speed) shortly after drivers are turned off.
  444. */
  445. //#define USE_CONTROLLER_FAN
  446. #if ENABLED(USE_CONTROLLER_FAN)
  447. //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
  448. //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered
  449. //#define CONTROLLER_FAN_IGNORE_Z // Ignore Z stepper. Useful when stepper timeout is disabled.
  450. #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
  451. #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled
  452. #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled
  453. #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors
  454. // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
  455. //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
  456. //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
  457. #if ENABLED(CONTROLLER_FAN_EDITABLE)
  458. #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
  459. #endif
  460. #endif
  461. // When first starting the main fan, run it at full speed for the
  462. // given number of milliseconds. This gets the fan spinning reliably
  463. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  464. //#define FAN_KICKSTART_TIME 100
  465. // Some coolers may require a non-zero "off" state.
  466. //#define FAN_OFF_PWM 1
  467. /**
  468. * PWM Fan Scaling
  469. *
  470. * Define the min/max speeds for PWM fans (as set with M106).
  471. *
  472. * With these options the M106 0-255 value range is scaled to a subset
  473. * to ensure that the fan has enough power to spin, or to run lower
  474. * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
  475. * Value 0 always turns off the fan.
  476. *
  477. * Define one or both of these to override the default 0-255 range.
  478. */
  479. //#define FAN_MIN_PWM 50
  480. //#define FAN_MAX_PWM 128
  481. /**
  482. * Fan Fast PWM
  483. *
  484. * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
  485. * to produce a frequency as close as possible to the desired frequency.
  486. *
  487. * FAST_PWM_FAN_FREQUENCY
  488. * Set this to your desired frequency.
  489. * For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
  490. * i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
  491. * For non AVR, if left undefined this defaults to F = 1Khz.
  492. * This F value is only to protect the hardware from an absence of configuration
  493. * and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
  494. *
  495. * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
  496. * Setting very high frequencies can damage your hardware.
  497. *
  498. * USE_OCR2A_AS_TOP [undefined by default]
  499. * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
  500. * 16MHz MCUs: [62.5kHz, 31.4kHz (default), 7.8kHz, 3.92kHz, 1.95kHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz]
  501. * 20MHz MCUs: [78.1kHz, 39.2kHz (default), 9.77kHz, 4.9kHz, 2.44kHz, 1.22kHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz]
  502. * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of
  503. * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  504. * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  505. */
  506. //#define FAST_PWM_FAN // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  507. #if ENABLED(FAST_PWM_FAN)
  508. //#define FAST_PWM_FAN_FREQUENCY 31400 // Define here to override the defaults below
  509. //#define USE_OCR2A_AS_TOP
  510. #ifndef FAST_PWM_FAN_FREQUENCY
  511. #ifdef __AVR__
  512. #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
  513. #else
  514. #define FAST_PWM_FAN_FREQUENCY 1000U
  515. #endif
  516. #endif
  517. #endif
  518. /**
  519. * Use one of the PWM fans as a redundant part-cooling fan
  520. */
  521. //#define REDUNDANT_PART_COOLING_FAN 2 // Index of the fan to sync with FAN 0.
  522. // @section extruder
  523. /**
  524. * Extruder cooling fans
  525. *
  526. * Extruder auto fans automatically turn on when their extruders'
  527. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  528. *
  529. * Your board's pins file specifies the recommended pins. Override those here
  530. * or set to -1 to disable completely.
  531. *
  532. * Multiple extruders can be assigned to the same pin in which case
  533. * the fan will turn on when any selected extruder is above the threshold.
  534. */
  535. #define E0_AUTO_FAN_PIN -1
  536. #define E1_AUTO_FAN_PIN -1
  537. #define E2_AUTO_FAN_PIN -1
  538. #define E3_AUTO_FAN_PIN -1
  539. #define E4_AUTO_FAN_PIN -1
  540. #define E5_AUTO_FAN_PIN -1
  541. #define E6_AUTO_FAN_PIN -1
  542. #define E7_AUTO_FAN_PIN -1
  543. #define CHAMBER_AUTO_FAN_PIN -1
  544. #define COOLER_AUTO_FAN_PIN -1
  545. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  546. #define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed
  547. #define CHAMBER_AUTO_FAN_TEMPERATURE 30
  548. #define CHAMBER_AUTO_FAN_SPEED 255
  549. #define COOLER_AUTO_FAN_TEMPERATURE 18
  550. #define COOLER_AUTO_FAN_SPEED 255
  551. /**
  552. * Hotend Cooling Fans tachometers
  553. *
  554. * Define one or more tachometer pins to enable fan speed
  555. * monitoring, and reporting of fan speeds with M123.
  556. *
  557. * NOTE: Only works with fans up to 7000 RPM.
  558. */
  559. //#define FOURWIRES_FANS // Needed with AUTO_FAN when 4-wire PWM fans are installed
  560. //#define E0_FAN_TACHO_PIN -1
  561. //#define E0_FAN_TACHO_PULLUP
  562. //#define E0_FAN_TACHO_PULLDOWN
  563. //#define E1_FAN_TACHO_PIN -1
  564. //#define E1_FAN_TACHO_PULLUP
  565. //#define E1_FAN_TACHO_PULLDOWN
  566. //#define E2_FAN_TACHO_PIN -1
  567. //#define E2_FAN_TACHO_PULLUP
  568. //#define E2_FAN_TACHO_PULLDOWN
  569. //#define E3_FAN_TACHO_PIN -1
  570. //#define E3_FAN_TACHO_PULLUP
  571. //#define E3_FAN_TACHO_PULLDOWN
  572. //#define E4_FAN_TACHO_PIN -1
  573. //#define E4_FAN_TACHO_PULLUP
  574. //#define E4_FAN_TACHO_PULLDOWN
  575. //#define E5_FAN_TACHO_PIN -1
  576. //#define E5_FAN_TACHO_PULLUP
  577. //#define E5_FAN_TACHO_PULLDOWN
  578. //#define E6_FAN_TACHO_PIN -1
  579. //#define E6_FAN_TACHO_PULLUP
  580. //#define E6_FAN_TACHO_PULLDOWN
  581. //#define E7_FAN_TACHO_PIN -1
  582. //#define E7_FAN_TACHO_PULLUP
  583. //#define E7_FAN_TACHO_PULLDOWN
  584. /**
  585. * Part-Cooling Fan Multiplexer
  586. *
  587. * This feature allows you to digitally multiplex the fan output.
  588. * The multiplexer is automatically switched at tool-change.
  589. * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
  590. */
  591. #define FANMUX0_PIN -1
  592. #define FANMUX1_PIN -1
  593. #define FANMUX2_PIN -1
  594. /**
  595. * M355 Case Light on-off / brightness
  596. */
  597. //#define CASE_LIGHT_ENABLE
  598. #if ENABLED(CASE_LIGHT_ENABLE)
  599. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  600. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  601. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  602. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  603. //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
  604. //#define CASE_LIGHT_MAX_PWM 128 // Limit PWM duty cycle (0-255)
  605. //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
  606. #if ENABLED(NEOPIXEL_LED)
  607. //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light
  608. #endif
  609. #if EITHER(RGB_LED, RGBW_LED)
  610. //#define CASE_LIGHT_USE_RGB_LED // Use RGB / RGBW LED as case light
  611. #endif
  612. #if EITHER(CASE_LIGHT_USE_NEOPIXEL, CASE_LIGHT_USE_RGB_LED)
  613. #define CASE_LIGHT_DEFAULT_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
  614. #endif
  615. #endif
  616. // @section homing
  617. // If you want endstops to stay on (by default) even when not homing
  618. // enable this option. Override at any time with M120, M121.
  619. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  620. // @section extras
  621. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  622. // Employ an external closed loop controller. Override pins here if needed.
  623. //#define EXTERNAL_CLOSED_LOOP_CONTROLLER
  624. #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
  625. //#define CLOSED_LOOP_ENABLE_PIN -1
  626. //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
  627. #endif
  628. /**
  629. * Dual X Carriage
  630. *
  631. * This setup has two X carriages that can move independently, each with its own hotend.
  632. * The carriages can be used to print an object with two colors or materials, or in
  633. * "duplication mode" it can print two identical or X-mirrored objects simultaneously.
  634. * The inactive carriage is parked automatically to prevent oozing.
  635. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis.
  636. * By default the X2 stepper is assigned to the first unused E plug on the board.
  637. *
  638. * The following Dual X Carriage modes can be selected with M605 S<mode>:
  639. *
  640. * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel
  641. * results as long as it supports dual X-carriages. (M605 S0)
  642. *
  643. * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so
  644. * that additional slicer support is not required. (M605 S1)
  645. *
  646. * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with
  647. * the first X-carriage and extruder, to print 2 copies of the same object at the same time.
  648. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and
  649. * follow with M605 S2 to initiate duplicated movement.
  650. *
  651. * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates
  652. * the movement of the first except the second extruder is reversed in the X axis.
  653. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
  654. * follow with M605 S3 to initiate mirrored movement.
  655. */
  656. //#define DUAL_X_CARRIAGE
  657. #if ENABLED(DUAL_X_CARRIAGE)
  658. #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS
  659. #define X1_MAX_POS X_BED_SIZE // A max coordinate so the X1 carriage can't hit the parked X2 carriage
  660. #define X2_MIN_POS 80 // A min coordinate so the X2 carriage can't hit the parked X1 carriage
  661. #define X2_MAX_POS 353 // The max position of the X2 carriage, typically also the home position
  662. #define X2_HOME_DIR 1 // Set to 1. The X2 carriage always homes to the max endstop position
  663. #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS.
  664. // NOTE: For Dual X Carriage use M218 T1 Xn to override the X2_HOME_POS.
  665. // This allows recalibration of endstops distance without a rebuild.
  666. // Remember to set the second extruder's X-offset to 0 in your slicer.
  667. // This is the default power-up mode which can be changed later using M605 S<mode>.
  668. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
  669. // Default x offset in duplication mode (typically set to half print bed width)
  670. #define DEFAULT_DUPLICATION_X_OFFSET 100
  671. // Default action to execute following M605 mode change commands. Typically G28X to apply new mode.
  672. //#define EVENT_GCODE_IDEX_AFTER_MODECHANGE "G28X"
  673. #endif
  674. /**
  675. * Multi-Stepper / Multi-Endstop
  676. *
  677. * When X2_DRIVER_TYPE is defined, this indicates that the X and X2 motors work in tandem.
  678. * The following explanations for X also apply to Y and Z multi-stepper setups.
  679. * Endstop offsets may be changed by 'M666 X<offset> Y<offset> Z<offset>' and stored to EEPROM.
  680. *
  681. * - Enable INVERT_X2_VS_X_DIR if the X2 motor requires an opposite DIR signal from X.
  682. *
  683. * - Enable X_DUAL_ENDSTOPS if the second motor has its own endstop, with adjustable offset.
  684. *
  685. * - Extra endstops are included in the output of 'M119'.
  686. *
  687. * - Set X_DUAL_ENDSTOP_ADJUSTMENT to the known error in the X2 endstop.
  688. * Applied to the X2 motor on 'G28' / 'G28 X'.
  689. * Get the offset by homing X and measuring the error.
  690. * Also set with 'M666 X<offset>' and stored to EEPROM with 'M500'.
  691. *
  692. * - Use X2_USE_ENDSTOP to set the endstop plug by name. (_XMIN_, _XMAX_, _YMIN_, _YMAX_, _ZMIN_, _ZMAX_)
  693. */
  694. #if HAS_X2_STEPPER && DISABLED(DUAL_X_CARRIAGE)
  695. //#define INVERT_X2_VS_X_DIR // X2 direction signal is the opposite of X
  696. //#define X_DUAL_ENDSTOPS // X2 has its own endstop
  697. #if ENABLED(X_DUAL_ENDSTOPS)
  698. #define X2_USE_ENDSTOP _XMAX_ // X2 endstop board plug. Don't forget to enable USE_*_PLUG.
  699. #define X2_ENDSTOP_ADJUSTMENT 0 // X2 offset relative to X endstop
  700. #endif
  701. #endif
  702. #if HAS_DUAL_Y_STEPPERS
  703. //#define INVERT_Y2_VS_Y_DIR // Y2 direction signal is the opposite of Y
  704. //#define Y_DUAL_ENDSTOPS // Y2 has its own endstop
  705. #if ENABLED(Y_DUAL_ENDSTOPS)
  706. #define Y2_USE_ENDSTOP _YMAX_ // Y2 endstop board plug. Don't forget to enable USE_*_PLUG.
  707. #define Y2_ENDSTOP_ADJUSTMENT 0 // Y2 offset relative to Y endstop
  708. #endif
  709. #endif
  710. //
  711. // Multi-Z steppers
  712. //
  713. #ifdef Z2_DRIVER_TYPE
  714. //#define INVERT_Z2_VS_Z_DIR // Z2 direction signal is the opposite of Z
  715. //#define Z_MULTI_ENDSTOPS // Other Z axes have their own endstops
  716. #if ENABLED(Z_MULTI_ENDSTOPS)
  717. #define Z2_USE_ENDSTOP _XMAX_ // Z2 endstop board plug. Don't forget to enable USE_*_PLUG.
  718. #define Z2_ENDSTOP_ADJUSTMENT 0 // Z2 offset relative to Y endstop
  719. #endif
  720. #ifdef Z3_DRIVER_TYPE
  721. //#define INVERT_Z3_VS_Z_DIR // Z3 direction signal is the opposite of Z
  722. #if ENABLED(Z_MULTI_ENDSTOPS)
  723. #define Z3_USE_ENDSTOP _YMAX_ // Z3 endstop board plug. Don't forget to enable USE_*_PLUG.
  724. #define Z3_ENDSTOP_ADJUSTMENT 0 // Z3 offset relative to Y endstop
  725. #endif
  726. #endif
  727. #ifdef Z4_DRIVER_TYPE
  728. //#define INVERT_Z4_VS_Z_DIR // Z4 direction signal is the opposite of Z
  729. #if ENABLED(Z_MULTI_ENDSTOPS)
  730. #define Z4_USE_ENDSTOP _ZMAX_ // Z4 endstop board plug. Don't forget to enable USE_*_PLUG.
  731. #define Z4_ENDSTOP_ADJUSTMENT 0 // Z4 offset relative to Y endstop
  732. #endif
  733. #endif
  734. #endif
  735. // Drive the E axis with two synchronized steppers
  736. //#define E_DUAL_STEPPER_DRIVERS
  737. #if ENABLED(E_DUAL_STEPPER_DRIVERS)
  738. //#define INVERT_E1_VS_E0_DIR // E direction signals are opposites
  739. #endif
  740. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  741. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  742. //#define EXT_SOLENOID
  743. // @section homing
  744. /**
  745. * Homing Procedure
  746. * Homing (G28) does an indefinite move towards the endstops to establish
  747. * the position of the toolhead relative to the workspace.
  748. */
  749. //#define SENSORLESS_BACKOFF_MM { 2, 2, 0 } // (linear=mm, rotational=°) Backoff from endstops before sensorless homing
  750. #define HOMING_BUMP_MM { 5, 5, 2 } // (linear=mm, rotational=°) Backoff from endstops after first bump
  751. #define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  752. //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing
  753. //#define QUICK_HOME // If G28 contains XY do a diagonal move first
  754. //#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
  755. //#define HOME_Z_FIRST // Home Z first. Requires a Z-MIN endstop (not a probe).
  756. //#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
  757. // @section bltouch
  758. #if ENABLED(BLTOUCH)
  759. /**
  760. * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
  761. * Do not activate settings that the probe might not understand. Clones might misunderstand
  762. * advanced commands.
  763. *
  764. * Note: If the probe is not deploying, do a "Reset" and "Self-Test" and then check the
  765. * wiring of the BROWN, RED and ORANGE wires.
  766. *
  767. * Note: If the trigger signal of your probe is not being recognized, it has been very often
  768. * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
  769. * like they would be with a real switch. So please check the wiring first.
  770. *
  771. * Settings for all BLTouch and clone probes:
  772. */
  773. // Safety: The probe needs time to recognize the command.
  774. // Minimum command delay (ms). Enable and increase if needed.
  775. //#define BLTOUCH_DELAY 500
  776. /**
  777. * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
  778. */
  779. // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
  780. // in special cases, like noisy or filtered input configurations.
  781. //#define BLTOUCH_FORCE_SW_MODE
  782. /**
  783. * Settings for BLTouch Smart 3.0 and 3.1
  784. * Summary:
  785. * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
  786. * - High-Speed mode
  787. * - Disable LCD voltage options
  788. */
  789. /**
  790. * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
  791. * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
  792. * If disabled, OD mode is the hard-coded default on 3.0
  793. * On startup, Marlin will compare its eeprom to this value. If the selected mode
  794. * differs, a mode set eeprom write will be completed at initialization.
  795. * Use the option below to force an eeprom write to a V3.1 probe regardless.
  796. */
  797. //#define BLTOUCH_SET_5V_MODE
  798. /**
  799. * Safety: Activate if connecting a probe with an unknown voltage mode.
  800. * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
  801. * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
  802. * To preserve the life of the probe, use this once then turn it off and re-flash.
  803. */
  804. //#define BLTOUCH_FORCE_MODE_SET
  805. /**
  806. * Enable "HIGH SPEED" option for probing.
  807. * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
  808. * This feature was designed for Deltabots with very fast Z moves; however, higher speed Cartesians
  809. * might be able to use it. If the machine can't raise Z fast enough the BLTouch may go into ALARM.
  810. *
  811. * Set the default state here, change with 'M401 S' or UI, use M500 to save, M502 to reset.
  812. */
  813. //#define BLTOUCH_HS_MODE true
  814. // Safety: Enable voltage mode settings in the LCD menu.
  815. //#define BLTOUCH_LCD_VOLTAGE_MENU
  816. #endif // BLTOUCH
  817. // @section extras
  818. /**
  819. * Z Steppers Auto-Alignment
  820. * Add the G34 command to align multiple Z steppers using a bed probe.
  821. */
  822. //#define Z_STEPPER_AUTO_ALIGN
  823. #if ENABLED(Z_STEPPER_AUTO_ALIGN)
  824. // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
  825. // If not defined, probe limits will be used.
  826. // Override with 'M422 S<index> X<pos> Y<pos>'
  827. //#define Z_STEPPER_ALIGN_XY { { 10, 190 }, { 100, 10 }, { 190, 190 } }
  828. /**
  829. * Orientation for the automatically-calculated probe positions.
  830. * Override Z stepper align points with 'M422 S<index> X<pos> Y<pos>'
  831. *
  832. * 2 Steppers: (0) (1)
  833. * | | 2 |
  834. * | 1 2 | |
  835. * | | 1 |
  836. *
  837. * 3 Steppers: (0) (1) (2) (3)
  838. * | 3 | 1 | 2 1 | 2 |
  839. * | | 3 | | 3 |
  840. * | 1 2 | 2 | 3 | 1 |
  841. *
  842. * 4 Steppers: (0) (1) (2) (3)
  843. * | 4 3 | 1 4 | 2 1 | 3 2 |
  844. * | | | | |
  845. * | 1 2 | 2 3 | 3 4 | 4 1 |
  846. */
  847. #ifndef Z_STEPPER_ALIGN_XY
  848. //#define Z_STEPPERS_ORIENTATION 0
  849. #endif
  850. /**
  851. * Z Stepper positions for more rapid convergence in bed alignment.
  852. * Requires 3 or 4 Z steppers.
  853. *
  854. * Define Stepper XY positions for Z1, Z2, Z3... corresponding to the screw
  855. * positions in the bed carriage, with one position per Z stepper in stepper
  856. * driver order.
  857. */
  858. //#define Z_STEPPER_ALIGN_STEPPER_XY { { 210.7, 102.5 }, { 152.6, 220.0 }, { 94.5, 102.5 } }
  859. #ifndef Z_STEPPER_ALIGN_STEPPER_XY
  860. // Amplification factor. Used to scale the correction step up or down in case
  861. // the stepper (spindle) position is farther out than the test point.
  862. #define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
  863. #endif
  864. // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
  865. #define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
  866. #define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
  867. #define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
  868. #define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
  869. // After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
  870. // Re-homing might be more precise in reproducing the actual 'G28 Z' homing height, especially on an uneven bed.
  871. #define HOME_AFTER_G34
  872. #endif
  873. //
  874. // Add the G35 command to read bed corners to help adjust screws. Requires a bed probe.
  875. //
  876. //#define ASSISTED_TRAMMING
  877. #if ENABLED(ASSISTED_TRAMMING)
  878. // Define positions for probe points.
  879. #define TRAMMING_POINT_XY { { 20, 20 }, { 180, 20 }, { 180, 180 }, { 20, 180 } }
  880. // Define position names for probe points.
  881. #define TRAMMING_POINT_NAME_1 "Front-Left"
  882. #define TRAMMING_POINT_NAME_2 "Front-Right"
  883. #define TRAMMING_POINT_NAME_3 "Back-Right"
  884. #define TRAMMING_POINT_NAME_4 "Back-Left"
  885. #define RESTORE_LEVELING_AFTER_G35 // Enable to restore leveling setup after operation
  886. //#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first
  887. //#define ASSISTED_TRAMMING_WIZARD // Add a Tramming Wizard to the LCD menu
  888. //#define ASSISTED_TRAMMING_WAIT_POSITION { X_CENTER, Y_CENTER, 30 } // Move the nozzle out of the way for adjustment
  889. /**
  890. * Screw thread:
  891. * M3: 30 = Clockwise, 31 = Counter-Clockwise
  892. * M4: 40 = Clockwise, 41 = Counter-Clockwise
  893. * M5: 50 = Clockwise, 51 = Counter-Clockwise
  894. */
  895. #define TRAMMING_SCREW_THREAD 30
  896. #endif
  897. // @section motion
  898. #define AXIS_RELATIVE_MODES { false, false, false, false }
  899. // Add a Duplicate option for well-separated conjoined nozzles
  900. //#define MULTI_NOZZLE_DUPLICATION
  901. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  902. #define INVERT_X_STEP_PIN false
  903. #define INVERT_Y_STEP_PIN false
  904. #define INVERT_Z_STEP_PIN false
  905. #define INVERT_I_STEP_PIN false
  906. #define INVERT_J_STEP_PIN false
  907. #define INVERT_K_STEP_PIN false
  908. #define INVERT_U_STEP_PIN false
  909. #define INVERT_V_STEP_PIN false
  910. #define INVERT_W_STEP_PIN false
  911. #define INVERT_E_STEP_PIN false
  912. /**
  913. * Idle Stepper Shutdown
  914. * Set DISABLE_INACTIVE_? 'true' to shut down axis steppers after an idle period.
  915. * The Deactive Time can be overridden with M18 and M84. Set to 0 for No Timeout.
  916. */
  917. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  918. #define DISABLE_INACTIVE_X true
  919. #define DISABLE_INACTIVE_Y true
  920. #define DISABLE_INACTIVE_Z true // Set 'false' if the nozzle could fall onto your printed part!
  921. #define DISABLE_INACTIVE_I true
  922. #define DISABLE_INACTIVE_J true
  923. #define DISABLE_INACTIVE_K true
  924. #define DISABLE_INACTIVE_U true
  925. #define DISABLE_INACTIVE_V true
  926. #define DISABLE_INACTIVE_W true
  927. #define DISABLE_INACTIVE_E true
  928. // Default Minimum Feedrates for printing and travel moves
  929. #define DEFAULT_MINIMUMFEEDRATE 0.0 // (mm/s. °/s for rotational-only moves) Minimum feedrate. Set with M205 S.
  930. #define DEFAULT_MINTRAVELFEEDRATE 0.0 // (mm/s. °/s for rotational-only moves) Minimum travel feedrate. Set with M205 T.
  931. // Minimum time that a segment needs to take as the buffer gets emptied
  932. #define DEFAULT_MINSEGMENTTIME 20000 // (µs) Set with M205 B.
  933. // Slow down the machine if the lookahead buffer is (by default) half full.
  934. // Increase the slowdown divisor for larger buffer sizes.
  935. #define SLOWDOWN
  936. #if ENABLED(SLOWDOWN)
  937. #define SLOWDOWN_DIVISOR 2
  938. #endif
  939. /**
  940. * XY Frequency limit
  941. * Reduce resonance by limiting the frequency of small zigzag infill moves.
  942. * See https://hydraraptor.blogspot.com/2010/12/frequency-limit.html
  943. * Use M201 F<freq> G<min%> to change limits at runtime.
  944. */
  945. //#define XY_FREQUENCY_LIMIT 10 // (Hz) Maximum frequency of small zigzag infill moves. Set with M201 F<hertz>.
  946. #ifdef XY_FREQUENCY_LIMIT
  947. #define XY_FREQUENCY_MIN_PERCENT 5 // (percent) Minimum FR percentage to apply. Set with M201 G<min%>.
  948. #endif
  949. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  950. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  951. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  952. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
  953. //
  954. // Backlash Compensation
  955. // Adds extra movement to axes on direction-changes to account for backlash.
  956. //
  957. //#define BACKLASH_COMPENSATION
  958. #if ENABLED(BACKLASH_COMPENSATION)
  959. // Define values for backlash distance and correction.
  960. // If BACKLASH_GCODE is enabled these values are the defaults.
  961. #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (linear=mm, rotational=°) One value for each linear axis
  962. #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction
  963. // Add steps for motor direction changes on CORE kinematics
  964. //#define CORE_BACKLASH
  965. // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments
  966. // to reduce print artifacts. (Enabling this is costly in memory and computation!)
  967. //#define BACKLASH_SMOOTHING_MM 3 // (mm)
  968. // Add runtime configuration and tuning of backlash values (M425)
  969. //#define BACKLASH_GCODE
  970. #if ENABLED(BACKLASH_GCODE)
  971. // Measure the Z backlash when probing (G29) and set with "M425 Z"
  972. #define MEASURE_BACKLASH_WHEN_PROBING
  973. #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
  974. // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT
  975. // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION
  976. // increments while checking for the contact to be broken.
  977. #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm)
  978. #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm)
  979. #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_FEEDRATE_SLOW // (mm/min)
  980. #endif
  981. #endif
  982. #endif
  983. /**
  984. * Automatic backlash, position and hotend offset calibration
  985. *
  986. * Enable G425 to run automatic calibration using an electrically-
  987. * conductive cube, bolt, or washer mounted on the bed.
  988. *
  989. * G425 uses the probe to touch the top and sides of the calibration object
  990. * on the bed and measures and/or correct positional offsets, axis backlash
  991. * and hotend offsets.
  992. *
  993. * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within
  994. * ±5mm of true values for G425 to succeed.
  995. */
  996. //#define CALIBRATION_GCODE
  997. #if ENABLED(CALIBRATION_GCODE)
  998. //#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
  999. //#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
  1000. #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm
  1001. #define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
  1002. #define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
  1003. #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
  1004. // The following parameters refer to the conical section of the nozzle tip.
  1005. #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
  1006. #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
  1007. // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM).
  1008. //#define CALIBRATION_REPORTING
  1009. // The true location and dimension the cube/bolt/washer on the bed.
  1010. #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
  1011. #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
  1012. // Comment out any sides which are unreachable by the probe. For best
  1013. // auto-calibration results, all sides must be reachable.
  1014. #define CALIBRATION_MEASURE_RIGHT
  1015. #define CALIBRATION_MEASURE_FRONT
  1016. #define CALIBRATION_MEASURE_LEFT
  1017. #define CALIBRATION_MEASURE_BACK
  1018. //#define CALIBRATION_MEASURE_IMIN
  1019. //#define CALIBRATION_MEASURE_IMAX
  1020. //#define CALIBRATION_MEASURE_JMIN
  1021. //#define CALIBRATION_MEASURE_JMAX
  1022. //#define CALIBRATION_MEASURE_KMIN
  1023. //#define CALIBRATION_MEASURE_KMAX
  1024. //#define CALIBRATION_MEASURE_UMIN
  1025. //#define CALIBRATION_MEASURE_UMAX
  1026. //#define CALIBRATION_MEASURE_VMIN
  1027. //#define CALIBRATION_MEASURE_VMAX
  1028. //#define CALIBRATION_MEASURE_WMIN
  1029. //#define CALIBRATION_MEASURE_WMAX
  1030. // Probing at the exact top center only works if the center is flat. If
  1031. // probing on a screwhead or hollow washer, probe near the edges.
  1032. //#define CALIBRATION_MEASURE_AT_TOP_EDGES
  1033. // Define the pin to read during calibration
  1034. #ifndef CALIBRATION_PIN
  1035. //#define CALIBRATION_PIN -1 // Define here to override the default pin
  1036. #define CALIBRATION_PIN_INVERTING false // Set to true to invert the custom pin
  1037. //#define CALIBRATION_PIN_PULLDOWN
  1038. #define CALIBRATION_PIN_PULLUP
  1039. #endif
  1040. #endif
  1041. /**
  1042. * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
  1043. * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
  1044. * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  1045. * lowest stepping frequencies.
  1046. */
  1047. //#define ADAPTIVE_STEP_SMOOTHING
  1048. /**
  1049. * Custom Microstepping
  1050. * Override as-needed for your setup. Up to 3 MS pins are supported.
  1051. */
  1052. //#define MICROSTEP1 LOW,LOW,LOW
  1053. //#define MICROSTEP2 HIGH,LOW,LOW
  1054. //#define MICROSTEP4 LOW,HIGH,LOW
  1055. //#define MICROSTEP8 HIGH,HIGH,LOW
  1056. //#define MICROSTEP16 LOW,LOW,HIGH
  1057. //#define MICROSTEP32 HIGH,LOW,HIGH
  1058. // Microstep settings (Requires a board with pins named X_MS1, X_MS2, etc.)
  1059. #define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
  1060. /**
  1061. * @section stepper motor current
  1062. *
  1063. * Some boards have a means of setting the stepper motor current via firmware.
  1064. *
  1065. * The power on motor currents are set by:
  1066. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  1067. * known compatible chips: A4982
  1068. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  1069. * known compatible chips: AD5206
  1070. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  1071. * known compatible chips: MCP4728
  1072. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE
  1073. * known compatible chips: MCP4451, MCP4018
  1074. *
  1075. * Motor currents can also be set by M907 - M910 and by the LCD.
  1076. * M907 - applies to all.
  1077. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  1078. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  1079. */
  1080. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  1081. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  1082. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  1083. /**
  1084. * I2C-based DIGIPOTs (e.g., Azteeg X3 Pro)
  1085. */
  1086. //#define DIGIPOT_MCP4018 // Requires https://github.com/felias-fogg/SlowSoftI2CMaster
  1087. //#define DIGIPOT_MCP4451
  1088. #if EITHER(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
  1089. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT:4 AZTEEG_X3_PRO:8 MKS_SBASE:5 MIGHTYBOARD_REVE:5
  1090. // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
  1091. // These correspond to the physical drivers, so be mindful if the order is changed.
  1092. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  1093. //#define DIGIPOT_USE_RAW_VALUES // Use DIGIPOT_MOTOR_CURRENT raw wiper values (instead of A4988 motor currents)
  1094. /**
  1095. * Common slave addresses:
  1096. *
  1097. * A (A shifted) B (B shifted) IC
  1098. * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
  1099. * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
  1100. * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451
  1101. * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451
  1102. * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018
  1103. */
  1104. //#define DIGIPOT_I2C_ADDRESS_A 0x2C // Unshifted slave address for first DIGIPOT
  1105. //#define DIGIPOT_I2C_ADDRESS_B 0x2D // Unshifted slave address for second DIGIPOT
  1106. #endif
  1107. //===========================================================================
  1108. //=============================Additional Features===========================
  1109. //===========================================================================
  1110. // @section lcd
  1111. #if HAS_MANUAL_MOVE_MENU
  1112. #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // (mm/min) Feedrates for manual moves along X, Y, Z, E from panel
  1113. #define FINE_MANUAL_MOVE 0.025 // (mm) Smallest manual move (< 0.1mm) applying to Z on most machines
  1114. #if IS_ULTIPANEL
  1115. #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
  1116. #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen
  1117. #endif
  1118. #endif
  1119. // Change values more rapidly when the encoder is rotated faster
  1120. #define ENCODER_RATE_MULTIPLIER
  1121. #if ENABLED(ENCODER_RATE_MULTIPLIER)
  1122. #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed
  1123. #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed
  1124. #endif
  1125. // Play a beep when the feedrate is changed from the Status Screen
  1126. //#define BEEP_ON_FEEDRATE_CHANGE
  1127. #if ENABLED(BEEP_ON_FEEDRATE_CHANGE)
  1128. #define FEEDRATE_CHANGE_BEEP_DURATION 10
  1129. #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
  1130. #endif
  1131. //
  1132. // LCD Backlight Timeout
  1133. //
  1134. //#define LCD_BACKLIGHT_TIMEOUT 30 // (s) Timeout before turning off the backlight
  1135. #if HAS_BED_PROBE && EITHER(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
  1136. //#define PROBE_OFFSET_WIZARD // Add a Probe Z Offset calibration option to the LCD menu
  1137. #if ENABLED(PROBE_OFFSET_WIZARD)
  1138. /**
  1139. * Enable to init the Probe Z-Offset when starting the Wizard.
  1140. * Use a height slightly above the estimated nozzle-to-probe Z offset.
  1141. * For example, with an offset of -5, consider a starting height of -4.
  1142. */
  1143. //#define PROBE_OFFSET_WIZARD_START_Z -4.0
  1144. // Set a convenient position to do the calibration (probing point and nozzle/bed-distance)
  1145. //#define PROBE_OFFSET_WIZARD_XY_POS { X_CENTER, Y_CENTER }
  1146. #endif
  1147. #endif
  1148. #if HAS_MARLINUI_MENU
  1149. #if HAS_BED_PROBE
  1150. // Add calibration in the Probe Offsets menu to compensate for X-axis twist.
  1151. //#define X_AXIS_TWIST_COMPENSATION
  1152. #if ENABLED(X_AXIS_TWIST_COMPENSATION)
  1153. /**
  1154. * Enable to init the Probe Z-Offset when starting the Wizard.
  1155. * Use a height slightly above the estimated nozzle-to-probe Z offset.
  1156. * For example, with an offset of -5, consider a starting height of -4.
  1157. */
  1158. #define XATC_START_Z 0.0
  1159. #define XATC_MAX_POINTS 3 // Number of points to probe in the wizard
  1160. #define XATC_Y_POSITION Y_CENTER // (mm) Y position to probe
  1161. #define XATC_Z_OFFSETS { 0, 0, 0 } // Z offsets for X axis sample points
  1162. #endif
  1163. // Show Deploy / Stow Probe options in the Motion menu.
  1164. #define PROBE_DEPLOY_STOW_MENU
  1165. #endif
  1166. // Include a page of printer information in the LCD Main Menu
  1167. //#define LCD_INFO_MENU
  1168. #if ENABLED(LCD_INFO_MENU)
  1169. //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
  1170. #endif
  1171. // BACK menu items keep the highlight at the top
  1172. //#define TURBO_BACK_MENU_ITEM
  1173. // Insert a menu for preheating at the top level to allow for quick access
  1174. //#define PREHEAT_SHORTCUT_MENU_ITEM
  1175. #endif // HAS_MARLINUI_MENU
  1176. #if EITHER(HAS_DISPLAY, DWIN_LCD_PROUI)
  1177. //#define SOUND_MENU_ITEM // Add a mute option to the LCD menu
  1178. #define SOUND_ON_DEFAULT // Buzzer/speaker default enabled state
  1179. #endif
  1180. #if EITHER(HAS_DISPLAY, DWIN_LCD_PROUI)
  1181. // The timeout to return to the status screen from sub-menus
  1182. //#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
  1183. #if ENABLED(SHOW_BOOTSCREEN)
  1184. #define BOOTSCREEN_TIMEOUT 4000 // (ms) Total Duration to display the boot screen(s)
  1185. #if EITHER(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
  1186. #define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
  1187. #endif
  1188. #endif
  1189. // Scroll a longer status message into view
  1190. //#define STATUS_MESSAGE_SCROLLING
  1191. // Apply a timeout to low-priority status messages
  1192. //#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
  1193. // On the Info Screen, display XY with one decimal place when possible
  1194. //#define LCD_DECIMAL_SMALL_XY
  1195. // Add an 'M73' G-code to set the current percentage
  1196. //#define LCD_SET_PROGRESS_MANUALLY
  1197. // Show the E position (filament used) during printing
  1198. //#define LCD_SHOW_E_TOTAL
  1199. /**
  1200. * LED Control Menu
  1201. * Add LED Control to the LCD menu
  1202. */
  1203. //#define LED_CONTROL_MENU
  1204. #if ENABLED(LED_CONTROL_MENU)
  1205. #define LED_COLOR_PRESETS // Enable the Preset Color menu option
  1206. //#define NEO2_COLOR_PRESETS // Enable a second NeoPixel Preset Color menu option
  1207. #if ENABLED(LED_COLOR_PRESETS)
  1208. #define LED_USER_PRESET_RED 255 // User defined RED value
  1209. #define LED_USER_PRESET_GREEN 128 // User defined GREEN value
  1210. #define LED_USER_PRESET_BLUE 0 // User defined BLUE value
  1211. #define LED_USER_PRESET_WHITE 255 // User defined WHITE value
  1212. #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  1213. //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
  1214. #endif
  1215. #if ENABLED(NEO2_COLOR_PRESETS)
  1216. #define NEO2_USER_PRESET_RED 255 // User defined RED value
  1217. #define NEO2_USER_PRESET_GREEN 128 // User defined GREEN value
  1218. #define NEO2_USER_PRESET_BLUE 0 // User defined BLUE value
  1219. #define NEO2_USER_PRESET_WHITE 255 // User defined WHITE value
  1220. #define NEO2_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  1221. //#define NEO2_USER_PRESET_STARTUP // Have the printer display the user preset color on startup for the second strip
  1222. #endif
  1223. #endif
  1224. #endif
  1225. // LCD Print Progress options
  1226. #if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
  1227. #if CAN_SHOW_REMAINING_TIME
  1228. //#define SHOW_REMAINING_TIME // Display estimated time to completion
  1229. #if ENABLED(SHOW_REMAINING_TIME)
  1230. //#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
  1231. //#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
  1232. #endif
  1233. #endif
  1234. #if EITHER(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI)
  1235. //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
  1236. #endif
  1237. #if EITHER(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
  1238. //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
  1239. #if ENABLED(LCD_PROGRESS_BAR)
  1240. #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
  1241. #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
  1242. #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
  1243. //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
  1244. //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
  1245. #endif
  1246. #endif
  1247. #endif
  1248. #if ENABLED(SDSUPPORT)
  1249. /**
  1250. * SD Card SPI Speed
  1251. * May be required to resolve "volume init" errors.
  1252. *
  1253. * Enable and set to SPI_HALF_SPEED, SPI_QUARTER_SPEED, or SPI_EIGHTH_SPEED
  1254. * otherwise full speed will be applied.
  1255. *
  1256. * :['SPI_HALF_SPEED', 'SPI_QUARTER_SPEED', 'SPI_EIGHTH_SPEED']
  1257. */
  1258. //#define SD_SPI_SPEED SPI_HALF_SPEED
  1259. // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
  1260. // Enable this option and set to HIGH if your SD cards are incorrectly detected.
  1261. //#define SD_DETECT_STATE HIGH
  1262. //#define SD_IGNORE_AT_STARTUP // Don't mount the SD card when starting up
  1263. //#define SDCARD_READONLY // Read-only SD card (to save over 2K of flash)
  1264. //#define GCODE_REPEAT_MARKERS // Enable G-code M808 to set repeat markers and do looping
  1265. #define SD_PROCEDURE_DEPTH 1 // Increase if you need more nested M32 calls
  1266. #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
  1267. #define SD_FINISHED_RELEASECOMMAND "M84" // Use "M84XYE" to keep Z enabled so your bed stays in place
  1268. // Reverse SD sort to show "more recent" files first, according to the card's FAT.
  1269. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
  1270. #define SDCARD_RATHERRECENTFIRST
  1271. #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing
  1272. //#define NO_SD_AUTOSTART // Remove auto#.g file support completely to save some Flash, SRAM
  1273. //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
  1274. //#define BROWSE_MEDIA_ON_INSERT // Open the file browser when media is inserted
  1275. //#define MEDIA_MENU_AT_TOP // Force the media menu to be listed on the top of the main menu
  1276. #define EVENT_GCODE_SD_ABORT "G28XY" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
  1277. #if ENABLED(PRINTER_EVENT_LEDS)
  1278. #define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
  1279. #endif
  1280. /**
  1281. * Continue after Power-Loss (Creality3D)
  1282. *
  1283. * Store the current state to the SD Card at the start of each layer
  1284. * during SD printing. If the recovery file is found at boot time, present
  1285. * an option on the LCD screen to continue the print from the last-known
  1286. * point in the file.
  1287. */
  1288. //#define POWER_LOSS_RECOVERY
  1289. #if ENABLED(POWER_LOSS_RECOVERY)
  1290. #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
  1291. //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
  1292. //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
  1293. //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
  1294. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
  1295. //#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor
  1296. //#define POWER_LOSS_PULLDOWN
  1297. //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
  1298. //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
  1299. // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
  1300. // especially with "vase mode" printing. Set too high and vases cannot be continued.
  1301. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
  1302. // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
  1303. //#define POWER_LOSS_RECOVER_ZHOME
  1304. #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
  1305. //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
  1306. #endif
  1307. #endif
  1308. /**
  1309. * Sort SD file listings in alphabetical order.
  1310. *
  1311. * With this option enabled, items on SD cards will be sorted
  1312. * by name for easier navigation.
  1313. *
  1314. * By default...
  1315. *
  1316. * - Use the slowest -but safest- method for sorting.
  1317. * - Folders are sorted to the top.
  1318. * - The sort key is statically allocated.
  1319. * - No added G-code (M34) support.
  1320. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  1321. *
  1322. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  1323. * compiler to calculate the worst-case usage and throw an error if the SRAM
  1324. * limit is exceeded.
  1325. *
  1326. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  1327. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  1328. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  1329. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  1330. */
  1331. //#define SDCARD_SORT_ALPHA
  1332. // SD Card Sorting options
  1333. #if ENABLED(SDCARD_SORT_ALPHA)
  1334. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
  1335. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  1336. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 G-code.
  1337. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
  1338. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  1339. #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  1340. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  1341. #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
  1342. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
  1343. #endif
  1344. // Allow international symbols in long filenames. To display correctly, the
  1345. // LCD's font must contain the characters. Check your selected LCD language.
  1346. //#define UTF_FILENAME_SUPPORT
  1347. //#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
  1348. //#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
  1349. //#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
  1350. //#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!)
  1351. /**
  1352. * Abort SD printing when any endstop is triggered.
  1353. * This feature is enabled with 'M540 S1' or from the LCD menu.
  1354. * Endstops must be activated for this option to work.
  1355. */
  1356. //#define SD_ABORT_ON_ENDSTOP_HIT
  1357. //#define SD_REPRINT_LAST_SELECTED_FILE // On print completion open the LCD Menu and select the same file
  1358. //#define AUTO_REPORT_SD_STATUS // Auto-report media status with 'M27 S<seconds>'
  1359. /**
  1360. * Support for USB thumb drives using an Arduino USB Host Shield or
  1361. * equivalent MAX3421E breakout board. The USB thumb drive will appear
  1362. * to Marlin as an SD card.
  1363. *
  1364. * The MAX3421E can be assigned the same pins as the SD card reader, with
  1365. * the following pin mapping:
  1366. *
  1367. * SCLK, MOSI, MISO --> SCLK, MOSI, MISO
  1368. * INT --> SD_DETECT_PIN [1]
  1369. * SS --> SDSS
  1370. *
  1371. * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility.
  1372. */
  1373. //#define USB_FLASH_DRIVE_SUPPORT
  1374. #if ENABLED(USB_FLASH_DRIVE_SUPPORT)
  1375. /**
  1376. * USB Host Shield Library
  1377. *
  1378. * - UHS2 uses no interrupts and has been production-tested
  1379. * on a LulzBot TAZ Pro with a 32-bit Archim board.
  1380. *
  1381. * - UHS3 is newer code with better USB compatibility. But it
  1382. * is less tested and is known to interfere with Servos.
  1383. * [1] This requires USB_INTR_PIN to be interrupt-capable.
  1384. */
  1385. //#define USE_UHS2_USB
  1386. //#define USE_UHS3_USB
  1387. /**
  1388. * Native USB Host supported by some boards (USB OTG)
  1389. */
  1390. //#define USE_OTG_USB_HOST
  1391. #if DISABLED(USE_OTG_USB_HOST)
  1392. #define USB_CS_PIN SDSS
  1393. #define USB_INTR_PIN SD_DETECT_PIN
  1394. #endif
  1395. #endif
  1396. /**
  1397. * When using a bootloader that supports SD-Firmware-Flashing,
  1398. * add a menu item to activate SD-FW-Update on the next reboot.
  1399. *
  1400. * Requires ATMEGA2560 (Arduino Mega)
  1401. *
  1402. * Tested with this bootloader:
  1403. * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560
  1404. */
  1405. //#define SD_FIRMWARE_UPDATE
  1406. #if ENABLED(SD_FIRMWARE_UPDATE)
  1407. #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF
  1408. #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0
  1409. #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF
  1410. #endif
  1411. /**
  1412. * Enable this option if you have more than ~3K of unused flash space.
  1413. * Marlin will embed all settings in the firmware binary as compressed data.
  1414. * Use 'M503 C' to write the settings out to the SD Card as 'mc.zip'.
  1415. * See docs/ConfigEmbedding.md for details on how to use 'mc-apply.py'.
  1416. */
  1417. //#define CONFIGURATION_EMBEDDING
  1418. // Add an optimized binary file transfer mode, initiated with 'M28 B1'
  1419. //#define BINARY_FILE_TRANSFER
  1420. #if ENABLED(BINARY_FILE_TRANSFER)
  1421. // Include extra facilities (e.g., 'M20 F') supporting firmware upload via BINARY_FILE_TRANSFER
  1422. //#define CUSTOM_FIRMWARE_UPLOAD
  1423. #endif
  1424. /**
  1425. * Set this option to one of the following (or the board's defaults apply):
  1426. *
  1427. * LCD - Use the SD drive in the external LCD controller.
  1428. * ONBOARD - Use the SD drive on the control board.
  1429. * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
  1430. *
  1431. * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
  1432. */
  1433. //#define SDCARD_CONNECTION LCD
  1434. // Enable if SD detect is rendered useless (e.g., by using an SD extender)
  1435. //#define NO_SD_DETECT
  1436. /**
  1437. * Multiple volume support - EXPERIMENTAL.
  1438. * Adds 'M21 Pm' / 'M21 S' / 'M21 U' to mount SD Card / USB Drive.
  1439. */
  1440. //#define MULTI_VOLUME
  1441. #if ENABLED(MULTI_VOLUME)
  1442. #define VOLUME_SD_ONBOARD
  1443. #define VOLUME_USB_FLASH_DRIVE
  1444. #define DEFAULT_VOLUME SV_SD_ONBOARD
  1445. #define DEFAULT_SHARED_VOLUME SV_USB_FLASH_DRIVE
  1446. #endif
  1447. #endif // SDSUPPORT
  1448. /**
  1449. * By default an onboard SD card reader may be shared as a USB mass-
  1450. * storage device. This option hides the SD card from the host PC.
  1451. */
  1452. //#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security).
  1453. /**
  1454. * Additional options for Graphical Displays
  1455. *
  1456. * Use the optimizations here to improve printing performance,
  1457. * which can be adversely affected by graphical display drawing,
  1458. * especially when doing several short moves, and when printing
  1459. * on DELTA and SCARA machines.
  1460. *
  1461. * Some of these options may result in the display lagging behind
  1462. * controller events, as there is a trade-off between reliable
  1463. * printing performance versus fast display updates.
  1464. */
  1465. #if HAS_MARLINUI_U8GLIB
  1466. // Save many cycles by drawing a hollow frame or no frame on the Info Screen
  1467. //#define XYZ_NO_FRAME
  1468. #define XYZ_HOLLOW_FRAME
  1469. // A bigger font is available for edit items. Costs 3120 bytes of flash.
  1470. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1471. //#define USE_BIG_EDIT_FONT
  1472. // A smaller font may be used on the Info Screen. Costs 2434 bytes of flash.
  1473. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1474. //#define USE_SMALL_INFOFONT
  1475. /**
  1476. * Graphical Display Sleep
  1477. *
  1478. * The U8G library provides sleep / wake functions for SH1106, SSD1306,
  1479. * SSD1309, and some other DOGM displays.
  1480. * Enable this option to save energy and prevent OLED pixel burn-in.
  1481. * Adds the menu item Configuration > LCD Timeout (m) to set a wait period
  1482. * from 0 (disabled) to 99 minutes.
  1483. */
  1484. //#define DISPLAY_SLEEP_MINUTES 2 // (minutes) Timeout before turning off the screen
  1485. /**
  1486. * ST7920-based LCDs can emulate a 16 x 4 character display using
  1487. * the ST7920 character-generator for very fast screen updates.
  1488. * Enable LIGHTWEIGHT_UI to use this special display mode.
  1489. *
  1490. * Since LIGHTWEIGHT_UI has limited space, the position and status
  1491. * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
  1492. * length of time to display the status message before clearing.
  1493. *
  1494. * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
  1495. * This will prevent position updates from being displayed.
  1496. */
  1497. #if IS_U8GLIB_ST7920
  1498. // Enable this option and reduce the value to optimize screen updates.
  1499. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  1500. //#define DOGM_SPI_DELAY_US 5
  1501. //#define LIGHTWEIGHT_UI
  1502. #if ENABLED(LIGHTWEIGHT_UI)
  1503. #define STATUS_EXPIRE_SECONDS 20
  1504. #endif
  1505. #endif
  1506. /**
  1507. * Status (Info) Screen customizations
  1508. * These options may affect code size and screen render time.
  1509. * Custom status screens can forcibly override these settings.
  1510. */
  1511. //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones
  1512. //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends)
  1513. #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM for numbered hotends)
  1514. #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating
  1515. #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating
  1516. #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating
  1517. //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active
  1518. //#define STATUS_COOLER_ANIM // Use a second bitmap to indicate laser cooling
  1519. //#define STATUS_FLOWMETER_ANIM // Use multiple bitmaps to indicate coolant flow
  1520. //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
  1521. //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
  1522. //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
  1523. //#define STATUS_HEAT_PERCENT // Show heating in a progress bar
  1524. //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash.
  1525. // Frivolous Game Options
  1526. //#define MARLIN_BRICKOUT
  1527. //#define MARLIN_INVADERS
  1528. //#define MARLIN_SNAKE
  1529. //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu
  1530. #endif // HAS_MARLINUI_U8GLIB
  1531. #if HAS_MARLINUI_U8GLIB || IS_DWIN_MARLINUI
  1532. // Show SD percentage next to the progress bar
  1533. //#define SHOW_SD_PERCENT
  1534. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  1535. #define MENU_HOLLOW_FRAME
  1536. // Swap the CW/CCW indicators in the graphics overlay
  1537. //#define OVERLAY_GFX_REVERSE
  1538. #endif
  1539. //
  1540. // Additional options for DGUS / DWIN displays
  1541. //
  1542. #if HAS_DGUS_LCD
  1543. #define LCD_BAUDRATE 115200
  1544. #define DGUS_RX_BUFFER_SIZE 128
  1545. #define DGUS_TX_BUFFER_SIZE 48
  1546. //#define SERIAL_STATS_RX_BUFFER_OVERRUNS // Fix Rx overrun situation (Currently only for AVR)
  1547. #define DGUS_UPDATE_INTERVAL_MS 500 // (ms) Interval between automatic screen updates
  1548. #if ANY(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_MKS, DGUS_LCD_UI_HIPRECY)
  1549. #define DGUS_PRINT_FILENAME // Display the filename during printing
  1550. #define DGUS_PREHEAT_UI // Display a preheat screen during heatup
  1551. #if EITHER(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_MKS)
  1552. //#define DGUS_UI_MOVE_DIS_OPTION // Disabled by default for FYSETC and MKS
  1553. #else
  1554. #define DGUS_UI_MOVE_DIS_OPTION // Enabled by default for UI_HIPRECY
  1555. #endif
  1556. #define DGUS_FILAMENT_LOADUNLOAD
  1557. #if ENABLED(DGUS_FILAMENT_LOADUNLOAD)
  1558. #define DGUS_FILAMENT_PURGE_LENGTH 10
  1559. #define DGUS_FILAMENT_LOAD_LENGTH_PER_TIME 0.5 // (mm) Adjust in proportion to DGUS_UPDATE_INTERVAL_MS
  1560. #endif
  1561. #define DGUS_UI_WAITING // Show a "waiting" screen between some screens
  1562. #if ENABLED(DGUS_UI_WAITING)
  1563. #define DGUS_UI_WAITING_STATUS 10
  1564. #define DGUS_UI_WAITING_STATUS_PERIOD 8 // Increase to slower waiting status looping
  1565. #endif
  1566. #endif
  1567. #endif // HAS_DGUS_LCD
  1568. //
  1569. // Additional options for AnyCubic Chiron TFT displays
  1570. //
  1571. #if ENABLED(ANYCUBIC_LCD_CHIRON)
  1572. // By default the type of panel is automatically detected.
  1573. // Enable one of these options if you know the panel type.
  1574. //#define CHIRON_TFT_STANDARD
  1575. //#define CHIRON_TFT_NEW
  1576. // Enable the longer Anycubic powerup startup tune
  1577. //#define AC_DEFAULT_STARTUP_TUNE
  1578. /**
  1579. * Display Folders
  1580. * By default the file browser lists all G-code files (including those in subfolders) in a flat list.
  1581. * Enable this option to display a hierarchical file browser.
  1582. *
  1583. * NOTES:
  1584. * - Without this option it helps to enable SDCARD_SORT_ALPHA so files are sorted before/after folders.
  1585. * - When used with the "new" panel, folder names will also have '.gcode' appended to their names.
  1586. * This hack is currently required to force the panel to show folders.
  1587. */
  1588. #define AC_SD_FOLDER_VIEW
  1589. #endif
  1590. //
  1591. // Specify additional languages for the UI. Default specified by LCD_LANGUAGE.
  1592. //
  1593. #if ANY(DOGLCD, TFT_COLOR_UI, TOUCH_UI_FTDI_EVE, IS_DWIN_MARLINUI)
  1594. //#define LCD_LANGUAGE_2 fr
  1595. //#define LCD_LANGUAGE_3 de
  1596. //#define LCD_LANGUAGE_4 es
  1597. //#define LCD_LANGUAGE_5 it
  1598. #ifdef LCD_LANGUAGE_2
  1599. //#define LCD_LANGUAGE_AUTO_SAVE // Automatically save language to EEPROM on change
  1600. #endif
  1601. #endif
  1602. //
  1603. // Touch UI for the FTDI Embedded Video Engine (EVE)
  1604. //
  1605. #if ENABLED(TOUCH_UI_FTDI_EVE)
  1606. // Display board used
  1607. //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240)
  1608. //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
  1609. //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272)
  1610. //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480)
  1611. //#define LCD_LULZBOT_CLCD_UI // LulzBot Color LCD UI
  1612. //#define LCD_FYSETC_TFT81050 // FYSETC with 5" (800x480)
  1613. //#define LCD_EVE3_50G // Matrix Orbital 5.0", 800x480, BT815
  1614. //#define LCD_EVE2_50G // Matrix Orbital 5.0", 800x480, FT813
  1615. // Correct the resolution if not using the stock TFT panel.
  1616. //#define TOUCH_UI_320x240
  1617. //#define TOUCH_UI_480x272
  1618. //#define TOUCH_UI_800x480
  1619. // Mappings for boards with a standard RepRapDiscount Display connector
  1620. //#define AO_EXP1_PINMAP // LulzBot CLCD UI EXP1 mapping
  1621. //#define AO_EXP2_PINMAP // LulzBot CLCD UI EXP2 mapping
  1622. //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping
  1623. //#define S6_TFT_PINMAP // FYSETC S6 pin mapping
  1624. //#define F6_TFT_PINMAP // FYSETC F6 pin mapping
  1625. //#define OTHER_PIN_LAYOUT // Define pins manually below
  1626. #if ENABLED(OTHER_PIN_LAYOUT)
  1627. // Pins for CS and MOD_RESET (PD) must be chosen
  1628. #define CLCD_MOD_RESET 9
  1629. #define CLCD_SPI_CS 10
  1630. // If using software SPI, specify pins for SCLK, MOSI, MISO
  1631. //#define CLCD_USE_SOFT_SPI
  1632. #if ENABLED(CLCD_USE_SOFT_SPI)
  1633. #define CLCD_SOFT_SPI_MOSI 11
  1634. #define CLCD_SOFT_SPI_MISO 12
  1635. #define CLCD_SOFT_SPI_SCLK 13
  1636. #endif
  1637. #endif
  1638. // Display Orientation. An inverted (i.e. upside-down) display
  1639. // is supported on the FT800. The FT810 and beyond also support
  1640. // portrait and mirrored orientations.
  1641. //#define TOUCH_UI_INVERTED
  1642. //#define TOUCH_UI_PORTRAIT
  1643. //#define TOUCH_UI_MIRRORED
  1644. // UTF8 processing and rendering.
  1645. // Unsupported characters are shown as '?'.
  1646. //#define TOUCH_UI_USE_UTF8
  1647. #if ENABLED(TOUCH_UI_USE_UTF8)
  1648. // Western accents support. These accented characters use
  1649. // combined bitmaps and require relatively little storage.
  1650. #define TOUCH_UI_UTF8_WESTERN_CHARSET
  1651. #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET)
  1652. // Additional character groups. These characters require
  1653. // full bitmaps and take up considerable storage:
  1654. //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³
  1655. //#define TOUCH_UI_UTF8_COPYRIGHT // © ®
  1656. //#define TOUCH_UI_UTF8_GERMANIC // ß
  1657. //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ
  1658. //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡
  1659. //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥
  1660. //#define TOUCH_UI_UTF8_ORDINALS // º ª
  1661. //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷
  1662. //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾
  1663. //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬
  1664. #endif
  1665. // Cyrillic character set, costs about 27KiB of flash
  1666. //#define TOUCH_UI_UTF8_CYRILLIC_CHARSET
  1667. #endif
  1668. // Use a smaller font when labels don't fit buttons
  1669. #define TOUCH_UI_FIT_TEXT
  1670. // Use a numeric passcode for "Screen lock" keypad.
  1671. // (recommended for smaller displays)
  1672. //#define TOUCH_UI_PASSCODE
  1673. // Output extra debug info for Touch UI events
  1674. //#define TOUCH_UI_DEBUG
  1675. // Developer menu (accessed by touching "About Printer" copyright text)
  1676. //#define TOUCH_UI_DEVELOPER_MENU
  1677. #endif
  1678. //
  1679. // Classic UI Options
  1680. //
  1681. #if TFT_SCALED_DOGLCD
  1682. //#define TFT_MARLINUI_COLOR 0xFFFF // White
  1683. //#define TFT_MARLINBG_COLOR 0x0000 // Black
  1684. //#define TFT_DISABLED_COLOR 0x0003 // Almost black
  1685. //#define TFT_BTCANCEL_COLOR 0xF800 // Red
  1686. //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow
  1687. //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan
  1688. #endif
  1689. //
  1690. // ADC Button Debounce
  1691. //
  1692. #if HAS_ADC_BUTTONS
  1693. #define ADC_BUTTON_DEBOUNCE_DELAY 16 // Increase if buttons bounce or repeat too fast
  1694. #endif
  1695. // @section safety
  1696. /**
  1697. * The watchdog hardware timer will do a reset and disable all outputs
  1698. * if the firmware gets too overloaded to read the temperature sensors.
  1699. *
  1700. * If you find that watchdog reboot causes your AVR board to hang forever,
  1701. * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
  1702. * NOTE: This method is less reliable as it can only catch hangups while
  1703. * interrupts are enabled.
  1704. */
  1705. #define USE_WATCHDOG
  1706. #if ENABLED(USE_WATCHDOG)
  1707. //#define WATCHDOG_RESET_MANUAL
  1708. #endif
  1709. // @section lcd
  1710. /**
  1711. * Babystepping enables movement of the axes by tiny increments without changing
  1712. * the current position values. This feature is used primarily to adjust the Z
  1713. * axis in the first layer of a print in real-time.
  1714. *
  1715. * Warning: Does not respect endstops!
  1716. */
  1717. //#define BABYSTEPPING
  1718. #if ENABLED(BABYSTEPPING)
  1719. //#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR
  1720. //#define BABYSTEP_WITHOUT_HOMING
  1721. //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
  1722. //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  1723. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  1724. //#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
  1725. #define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
  1726. #define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
  1727. //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  1728. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
  1729. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
  1730. // Note: Extra time may be added to mitigate controller latency.
  1731. //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
  1732. #if ENABLED(MOVE_Z_WHEN_IDLE)
  1733. #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size.
  1734. #endif
  1735. #endif
  1736. //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
  1737. //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
  1738. #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
  1739. //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
  1740. //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
  1741. #endif
  1742. #endif
  1743. // @section extruder
  1744. /**
  1745. * Linear Pressure Control v1.5
  1746. *
  1747. * Assumption: advance [steps] = k * (delta velocity [steps/s])
  1748. * K=0 means advance disabled.
  1749. *
  1750. * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
  1751. *
  1752. * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
  1753. * Larger K values will be needed for flexible filament and greater distances.
  1754. * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
  1755. * print acceleration will be reduced during the affected moves to keep within the limit.
  1756. *
  1757. * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  1758. */
  1759. //#define LIN_ADVANCE
  1760. #if ENABLED(LIN_ADVANCE)
  1761. //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
  1762. #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
  1763. //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
  1764. //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
  1765. //#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends.
  1766. #endif
  1767. // @section leveling
  1768. /**
  1769. * Use Safe Bed Leveling coordinates to move axes to a useful position before bed probing.
  1770. * For example, after homing a rotational axis the Z probe might not be perpendicular to the bed.
  1771. * Choose values the orient the bed horizontally and the Z-probe vertically.
  1772. */
  1773. //#define SAFE_BED_LEVELING_START_X 0.0
  1774. //#define SAFE_BED_LEVELING_START_Y 0.0
  1775. //#define SAFE_BED_LEVELING_START_Z 0.0
  1776. //#define SAFE_BED_LEVELING_START_I 0.0
  1777. //#define SAFE_BED_LEVELING_START_J 0.0
  1778. //#define SAFE_BED_LEVELING_START_K 0.0
  1779. //#define SAFE_BED_LEVELING_START_U 0.0
  1780. //#define SAFE_BED_LEVELING_START_V 0.0
  1781. //#define SAFE_BED_LEVELING_START_W 0.0
  1782. /**
  1783. * Points to probe for all 3-point Leveling procedures.
  1784. * Override if the automatically selected points are inadequate.
  1785. */
  1786. #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
  1787. //#define PROBE_PT_1_X 15
  1788. //#define PROBE_PT_1_Y 180
  1789. //#define PROBE_PT_2_X 15
  1790. //#define PROBE_PT_2_Y 20
  1791. //#define PROBE_PT_3_X 170
  1792. //#define PROBE_PT_3_Y 20
  1793. #endif
  1794. /**
  1795. * Probing Margins
  1796. *
  1797. * Override PROBING_MARGIN for each side of the build plate
  1798. * Useful to get probe points to exact positions on targets or
  1799. * to allow leveling to avoid plate clamps on only specific
  1800. * sides of the bed. With NOZZLE_AS_PROBE negative values are
  1801. * allowed, to permit probing outside the bed.
  1802. *
  1803. * If you are replacing the prior *_PROBE_BED_POSITION options,
  1804. * LEFT and FRONT values in most cases will map directly over
  1805. * RIGHT and REAR would be the inverse such as
  1806. * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
  1807. *
  1808. * This will allow all positions to match at compilation, however
  1809. * should the probe position be modified with M851XY then the
  1810. * probe points will follow. This prevents any change from causing
  1811. * the probe to be unable to reach any points.
  1812. */
  1813. #if PROBE_SELECTED && !IS_KINEMATIC
  1814. //#define PROBING_MARGIN_LEFT PROBING_MARGIN
  1815. //#define PROBING_MARGIN_RIGHT PROBING_MARGIN
  1816. //#define PROBING_MARGIN_FRONT PROBING_MARGIN
  1817. //#define PROBING_MARGIN_BACK PROBING_MARGIN
  1818. #endif
  1819. #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
  1820. // Override the mesh area if the automatic (max) area is too large
  1821. //#define MESH_MIN_X MESH_INSET
  1822. //#define MESH_MIN_Y MESH_INSET
  1823. //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
  1824. //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
  1825. #endif
  1826. #if BOTH(AUTO_BED_LEVELING_UBL, EEPROM_SETTINGS)
  1827. //#define OPTIMIZED_MESH_STORAGE // Store mesh with less precision to save EEPROM space
  1828. #endif
  1829. /**
  1830. * Repeatedly attempt G29 leveling until it succeeds.
  1831. * Stop after G29_MAX_RETRIES attempts.
  1832. */
  1833. //#define G29_RETRY_AND_RECOVER
  1834. #if ENABLED(G29_RETRY_AND_RECOVER)
  1835. #define G29_MAX_RETRIES 3
  1836. #define G29_HALT_ON_FAILURE
  1837. /**
  1838. * Specify the GCODE commands that will be executed when leveling succeeds,
  1839. * between attempts, and after the maximum number of retries have been tried.
  1840. */
  1841. #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
  1842. #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
  1843. #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
  1844. #endif
  1845. /**
  1846. * Thermal Probe Compensation
  1847. *
  1848. * Adjust probe measurements to compensate for distortion associated with the temperature
  1849. * of the probe, bed, and/or hotend.
  1850. * Use G76 to automatically calibrate this feature for probe and bed temperatures.
  1851. * (Extruder temperature/offset values must be calibrated manually.)
  1852. * Use M871 to set temperature/offset values manually.
  1853. * For more details see https://marlinfw.org/docs/features/probe_temp_compensation.html
  1854. */
  1855. //#define PTC_PROBE // Compensate based on probe temperature
  1856. //#define PTC_BED // Compensate based on bed temperature
  1857. //#define PTC_HOTEND // Compensate based on hotend temperature
  1858. #if ANY(PTC_PROBE, PTC_BED, PTC_HOTEND)
  1859. /**
  1860. * If the probe is outside the defined range, use linear extrapolation with the closest
  1861. * point and the point with index PTC_LINEAR_EXTRAPOLATION. e.g., If set to 4 it will use the
  1862. * linear extrapolation between data[0] and data[4] for values below PTC_PROBE_START.
  1863. */
  1864. //#define PTC_LINEAR_EXTRAPOLATION 4
  1865. #if ENABLED(PTC_PROBE)
  1866. // Probe temperature calibration generates a table of values starting at PTC_PROBE_START
  1867. // (e.g., 30), in steps of PTC_PROBE_RES (e.g., 5) with PTC_PROBE_COUNT (e.g., 10) samples.
  1868. #define PTC_PROBE_START 30 // (°C)
  1869. #define PTC_PROBE_RES 5 // (°C)
  1870. #define PTC_PROBE_COUNT 10
  1871. #define PTC_PROBE_ZOFFS { 0 } // (µm) Z adjustments per sample
  1872. #endif
  1873. #if ENABLED(PTC_BED)
  1874. // Bed temperature calibration builds a similar table.
  1875. #define PTC_BED_START 60 // (°C)
  1876. #define PTC_BED_RES 5 // (°C)
  1877. #define PTC_BED_COUNT 10
  1878. #define PTC_BED_ZOFFS { 0 } // (µm) Z adjustments per sample
  1879. #endif
  1880. #if ENABLED(PTC_HOTEND)
  1881. // Note: There is no automatic calibration for the hotend. Use M871.
  1882. #define PTC_HOTEND_START 180 // (°C)
  1883. #define PTC_HOTEND_RES 5 // (°C)
  1884. #define PTC_HOTEND_COUNT 20
  1885. #define PTC_HOTEND_ZOFFS { 0 } // (µm) Z adjustments per sample
  1886. #endif
  1887. // G76 options
  1888. #if BOTH(PTC_PROBE, PTC_BED)
  1889. // Park position to wait for probe cooldown
  1890. #define PTC_PARK_POS { 0, 0, 100 }
  1891. // Probe position to probe and wait for probe to reach target temperature
  1892. //#define PTC_PROBE_POS { 12.0f, 7.3f } // Example: MK52 magnetic heatbed
  1893. #define PTC_PROBE_POS { 90, 100 }
  1894. // The temperature the probe should be at while taking measurements during
  1895. // bed temperature calibration.
  1896. #define PTC_PROBE_TEMP 30 // (°C)
  1897. // Height above Z=0.0 to raise the nozzle. Lowering this can help the probe to heat faster.
  1898. // Note: The Z=0.0 offset is determined by the probe Z offset (e.g., as set with M851 Z).
  1899. #define PTC_PROBE_HEATING_OFFSET 0.5
  1900. #endif
  1901. #endif // PTC_PROBE || PTC_BED || PTC_HOTEND
  1902. // @section extras
  1903. //
  1904. // G60/G61 Position Save and Return
  1905. //
  1906. //#define SAVED_POSITIONS 1 // Each saved position slot costs 12 bytes
  1907. //
  1908. // G2/G3 Arc Support
  1909. //
  1910. #define ARC_SUPPORT // Requires ~3226 bytes
  1911. #if ENABLED(ARC_SUPPORT)
  1912. #define MIN_ARC_SEGMENT_MM 0.1 // (mm) Minimum length of each arc segment
  1913. #define MAX_ARC_SEGMENT_MM 1.0 // (mm) Maximum length of each arc segment
  1914. #define MIN_CIRCLE_SEGMENTS 72 // Minimum number of segments in a complete circle
  1915. //#define ARC_SEGMENTS_PER_SEC 50 // Use the feedrate to choose the segment length
  1916. #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections
  1917. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  1918. //#define SF_ARC_FIX // Enable only if using SkeinForge with "Arc Point" fillet procedure
  1919. #endif
  1920. // G5 Bézier Curve Support with XYZE destination and IJPQ offsets
  1921. //#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes
  1922. #if EITHER(ARC_SUPPORT, BEZIER_CURVE_SUPPORT)
  1923. //#define CNC_WORKSPACE_PLANES // Allow G2/G3/G5 to operate in XY, ZX, or YZ planes
  1924. #endif
  1925. /**
  1926. * Direct Stepping
  1927. *
  1928. * Comparable to the method used by Klipper, G6 direct stepping significantly
  1929. * reduces motion calculations, increases top printing speeds, and results in
  1930. * less step aliasing by calculating all motions in advance.
  1931. * Preparing your G-code: https://github.com/colinrgodsey/step-daemon
  1932. */
  1933. //#define DIRECT_STEPPING
  1934. /**
  1935. * G38 Probe Target
  1936. *
  1937. * This option adds G38.2 and G38.3 (probe towards target)
  1938. * and optionally G38.4 and G38.5 (probe away from target).
  1939. * Set MULTIPLE_PROBING for G38 to probe more than once.
  1940. */
  1941. //#define G38_PROBE_TARGET
  1942. #if ENABLED(G38_PROBE_TARGET)
  1943. //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target
  1944. #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move.
  1945. #endif
  1946. // Moves (or segments) with fewer steps than this will be joined with the next move
  1947. #define MIN_STEPS_PER_SEGMENT 6
  1948. /**
  1949. * Minimum delay before and after setting the stepper DIR (in ns)
  1950. * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
  1951. * 20 : Minimum for TMC2xxx drivers
  1952. * 200 : Minimum for A4988 drivers
  1953. * 400 : Minimum for A5984 drivers
  1954. * 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
  1955. * 650 : Minimum for DRV8825 drivers
  1956. * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
  1957. * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
  1958. *
  1959. * Override the default value based on the driver type set in Configuration.h.
  1960. */
  1961. //#define MINIMUM_STEPPER_POST_DIR_DELAY 650
  1962. //#define MINIMUM_STEPPER_PRE_DIR_DELAY 650
  1963. /**
  1964. * Minimum stepper driver pulse width (in µs)
  1965. * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
  1966. * 0 : Minimum 500ns for LV8729, adjusted in stepper.h
  1967. * 1 : Minimum for A4988 and A5984 stepper drivers
  1968. * 2 : Minimum for DRV8825 stepper drivers
  1969. * 3 : Minimum for TB6600 stepper drivers
  1970. * 30 : Minimum for TB6560 stepper drivers
  1971. *
  1972. * Override the default value based on the driver type set in Configuration.h.
  1973. */
  1974. //#define MINIMUM_STEPPER_PULSE 2
  1975. /**
  1976. * Maximum stepping rate (in Hz) the stepper driver allows
  1977. * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
  1978. * 5000000 : Maximum for TMC2xxx stepper drivers
  1979. * 1000000 : Maximum for LV8729 stepper driver
  1980. * 500000 : Maximum for A4988 stepper driver
  1981. * 250000 : Maximum for DRV8825 stepper driver
  1982. * 150000 : Maximum for TB6600 stepper driver
  1983. * 15000 : Maximum for TB6560 stepper driver
  1984. *
  1985. * Override the default value based on the driver type set in Configuration.h.
  1986. */
  1987. //#define MAXIMUM_STEPPER_RATE 250000
  1988. // @section temperature
  1989. // Control heater 0 and heater 1 in parallel.
  1990. //#define HEATERS_PARALLEL
  1991. //===========================================================================
  1992. //================================= Buffers =================================
  1993. //===========================================================================
  1994. // @section motion
  1995. // The number of linear moves that can be in the planner at once.
  1996. // The value of BLOCK_BUFFER_SIZE must be a power of 2 (e.g., 8, 16, 32)
  1997. #if BOTH(SDSUPPORT, DIRECT_STEPPING)
  1998. #define BLOCK_BUFFER_SIZE 8
  1999. #elif ENABLED(SDSUPPORT)
  2000. #define BLOCK_BUFFER_SIZE 16
  2001. #else
  2002. #define BLOCK_BUFFER_SIZE 16
  2003. #endif
  2004. // @section serial
  2005. // The ASCII buffer for serial input
  2006. #define MAX_CMD_SIZE 96
  2007. #define BUFSIZE 4
  2008. // Transmission to Host Buffer Size
  2009. // To save 386 bytes of flash (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  2010. // To buffer a simple "ok" you need 4 bytes.
  2011. // For ADVANCED_OK (M105) you need 32 bytes.
  2012. // For debug-echo: 128 bytes for the optimal speed.
  2013. // Other output doesn't need to be that speedy.
  2014. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  2015. #define TX_BUFFER_SIZE 0
  2016. // Host Receive Buffer Size
  2017. // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
  2018. // To use flow control, set this buffer size to at least 1024 bytes.
  2019. // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
  2020. //#define RX_BUFFER_SIZE 1024
  2021. #if RX_BUFFER_SIZE >= 1024
  2022. // Enable to have the controller send XON/XOFF control characters to
  2023. // the host to signal the RX buffer is becoming full.
  2024. //#define SERIAL_XON_XOFF
  2025. #endif
  2026. #if ENABLED(SDSUPPORT)
  2027. // Enable this option to collect and display the maximum
  2028. // RX queue usage after transferring a file to SD.
  2029. //#define SERIAL_STATS_MAX_RX_QUEUED
  2030. // Enable this option to collect and display the number
  2031. // of dropped bytes after a file transfer to SD.
  2032. //#define SERIAL_STATS_DROPPED_RX
  2033. #endif
  2034. // Monitor RX buffer usage
  2035. // Dump an error to the serial port if the serial receive buffer overflows.
  2036. // If you see these errors, increase the RX_BUFFER_SIZE value.
  2037. // Not supported on all platforms.
  2038. //#define RX_BUFFER_MONITOR
  2039. /**
  2040. * Emergency Command Parser
  2041. *
  2042. * Add a low-level parser to intercept certain commands as they
  2043. * enter the serial receive buffer, so they cannot be blocked.
  2044. * Currently handles M108, M112, M410, M876
  2045. * NOTE: Not yet implemented for all platforms.
  2046. */
  2047. //#define EMERGENCY_PARSER
  2048. /**
  2049. * Realtime Reporting (requires EMERGENCY_PARSER)
  2050. *
  2051. * - Report position and state of the machine (like Grbl).
  2052. * - Auto-report position during long moves.
  2053. * - Useful for CNC/LASER.
  2054. *
  2055. * Adds support for commands:
  2056. * S000 : Report State and Position while moving.
  2057. * P000 : Instant Pause / Hold while moving.
  2058. * R000 : Resume from Pause / Hold.
  2059. *
  2060. * - During Hold all Emergency Parser commands are available, as usual.
  2061. * - Enable NANODLP_Z_SYNC and NANODLP_ALL_AXIS for move command end-state reports.
  2062. */
  2063. //#define REALTIME_REPORTING_COMMANDS
  2064. #if ENABLED(REALTIME_REPORTING_COMMANDS)
  2065. //#define FULL_REPORT_TO_HOST_FEATURE // Auto-report the machine status like Grbl CNC
  2066. #endif
  2067. // Bad Serial-connections can miss a received command by sending an 'ok'
  2068. // Therefore some clients abort after 30 seconds in a timeout.
  2069. // Some other clients start sending commands while receiving a 'wait'.
  2070. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  2071. //#define NO_TIMEOUTS 1000 // Milliseconds
  2072. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  2073. //#define ADVANCED_OK
  2074. // Printrun may have trouble receiving long strings all at once.
  2075. // This option inserts short delays between lines of serial output.
  2076. #define SERIAL_OVERRUN_PROTECTION
  2077. // For serial echo, the number of digits after the decimal point
  2078. //#define SERIAL_FLOAT_PRECISION 4
  2079. /**
  2080. * Set the number of proportional font spaces required to fill up a typical character space.
  2081. * This can help to better align the output of commands like `G29 O` Mesh Output.
  2082. *
  2083. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  2084. * Otherwise, adjust according to your client and font.
  2085. */
  2086. #define PROPORTIONAL_FONT_RATIO 1.0
  2087. // @section extras
  2088. /**
  2089. * Extra Fan Speed
  2090. * Adds a secondary fan speed for each print-cooling fan.
  2091. * 'M106 P<fan> T3-255' : Set a secondary speed for <fan>
  2092. * 'M106 P<fan> T2' : Use the set secondary speed
  2093. * 'M106 P<fan> T1' : Restore the previous fan speed
  2094. */
  2095. //#define EXTRA_FAN_SPEED
  2096. /**
  2097. * Firmware-based and LCD-controlled retract
  2098. *
  2099. * Add G10 / G11 commands for automatic firmware-based retract / recover.
  2100. * Use M207 and M208 to define parameters for retract / recover.
  2101. *
  2102. * Use M209 to enable or disable auto-retract.
  2103. * With auto-retract enabled, all G1 E moves within the set range
  2104. * will be converted to firmware-based retract/recover moves.
  2105. *
  2106. * Be sure to turn off auto-retract during filament change.
  2107. *
  2108. * Note that M207 / M208 / M209 settings are saved to EEPROM.
  2109. */
  2110. //#define FWRETRACT
  2111. #if ENABLED(FWRETRACT)
  2112. #define FWRETRACT_AUTORETRACT // Override slicer retractions
  2113. #if ENABLED(FWRETRACT_AUTORETRACT)
  2114. #define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length
  2115. #define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length
  2116. #endif
  2117. #define RETRACT_LENGTH 3 // (mm) Default retract length (positive value)
  2118. #define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value)
  2119. #define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting
  2120. #define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise
  2121. #define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover)
  2122. #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
  2123. #define RETRACT_RECOVER_FEEDRATE 8 // (mm/s) Default feedrate for recovering from retraction
  2124. #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction
  2125. #if ENABLED(MIXING_EXTRUDER)
  2126. //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously
  2127. #endif
  2128. #endif
  2129. /**
  2130. * Universal tool change settings.
  2131. * Applies to all types of extruders except where explicitly noted.
  2132. */
  2133. #if HAS_MULTI_EXTRUDER
  2134. // Z raise distance for tool-change, as needed for some extruders
  2135. #define TOOLCHANGE_ZRAISE 2 // (mm)
  2136. //#define TOOLCHANGE_ZRAISE_BEFORE_RETRACT // Apply raise before swap retraction (if enabled)
  2137. //#define TOOLCHANGE_NO_RETURN // Never return to previous position on tool-change
  2138. #if ENABLED(TOOLCHANGE_NO_RETURN)
  2139. //#define EVENT_GCODE_AFTER_TOOLCHANGE "G12X" // Extra G-code to run after tool-change
  2140. #endif
  2141. /**
  2142. * Extra G-code to run while executing tool-change commands. Can be used to use an additional
  2143. * stepper motor (e.g., I axis in Configuration.h) to drive the tool-changer.
  2144. */
  2145. //#define EVENT_GCODE_TOOLCHANGE_T0 "G28 A\nG1 A0" // Extra G-code to run while executing tool-change command T0
  2146. //#define EVENT_GCODE_TOOLCHANGE_T1 "G1 A10" // Extra G-code to run while executing tool-change command T1
  2147. //#define EVENT_GCODE_TOOLCHANGE_ALWAYS_RUN // Always execute above G-code sequences. Use with caution!
  2148. /**
  2149. * Tool Sensors detect when tools have been picked up or dropped.
  2150. * Requires the pins TOOL_SENSOR1_PIN, TOOL_SENSOR2_PIN, etc.
  2151. */
  2152. //#define TOOL_SENSOR
  2153. /**
  2154. * Retract and prime filament on tool-change to reduce
  2155. * ooze and stringing and to get cleaner transitions.
  2156. */
  2157. //#define TOOLCHANGE_FILAMENT_SWAP
  2158. #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
  2159. // Load / Unload
  2160. #define TOOLCHANGE_FS_LENGTH 12 // (mm) Load / Unload length
  2161. #define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH 0 // (mm) Extra length for better restart. Adjust with LCD or M217 B.
  2162. #define TOOLCHANGE_FS_RETRACT_SPEED (50*60) // (mm/min) (Unloading)
  2163. #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/min) (On SINGLENOZZLE or Bowden loading must be slowed down)
  2164. // Longer prime to clean out a SINGLENOZZLE
  2165. #define TOOLCHANGE_FS_EXTRA_PRIME 0 // (mm) Extra priming length
  2166. #define TOOLCHANGE_FS_PRIME_SPEED (4.6*60) // (mm/min) Extra priming feedrate
  2167. #define TOOLCHANGE_FS_WIPE_RETRACT 0 // (mm) Retract before cooling for less stringing, better wipe, etc.
  2168. // Cool after prime to reduce stringing
  2169. #define TOOLCHANGE_FS_FAN -1 // Fan index or -1 to skip
  2170. #define TOOLCHANGE_FS_FAN_SPEED 255 // 0-255
  2171. #define TOOLCHANGE_FS_FAN_TIME 10 // (seconds)
  2172. // Use TOOLCHANGE_FS_PRIME_SPEED feedrate the first time each extruder is primed
  2173. //#define TOOLCHANGE_FS_SLOW_FIRST_PRIME
  2174. /**
  2175. * Prime T0 the first time T0 is sent to the printer:
  2176. * [ Power-On -> T0 { Activate & Prime T0 } -> T1 { Retract T0, Activate & Prime T1 } ]
  2177. * If disabled, no priming on T0 until switching back to T0 from another extruder:
  2178. * [ Power-On -> T0 { T0 Activated } -> T1 { Activate & Prime T1 } -> T0 { Retract T1, Activate & Prime T0 } ]
  2179. * Enable with M217 V1 before printing to avoid unwanted priming on host connect.
  2180. */
  2181. //#define TOOLCHANGE_FS_PRIME_FIRST_USED
  2182. /**
  2183. * Tool Change Migration
  2184. * This feature provides G-code and LCD options to switch tools mid-print.
  2185. * All applicable tool properties are migrated so the print can continue.
  2186. * Tools must be closely matching and other restrictions may apply.
  2187. * Useful to:
  2188. * - Change filament color without interruption
  2189. * - Switch spools automatically on filament runout
  2190. * - Switch to a different nozzle on an extruder jam
  2191. */
  2192. #define TOOLCHANGE_MIGRATION_FEATURE
  2193. #endif
  2194. /**
  2195. * Position to park head during tool change.
  2196. * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER
  2197. */
  2198. //#define TOOLCHANGE_PARK
  2199. #if ENABLED(TOOLCHANGE_PARK)
  2200. #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 }
  2201. #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/min)
  2202. //#define TOOLCHANGE_PARK_X_ONLY // X axis only move
  2203. //#define TOOLCHANGE_PARK_Y_ONLY // Y axis only move
  2204. #endif
  2205. #endif // HAS_MULTI_EXTRUDER
  2206. /**
  2207. * Advanced Pause for Filament Change
  2208. * - Adds the G-code M600 Filament Change to initiate a filament change.
  2209. * - This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  2210. *
  2211. * Requirements:
  2212. * - For Filament Change parking enable and configure NOZZLE_PARK_FEATURE.
  2213. * - For user interaction enable an LCD display, HOST_PROMPT_SUPPORT, or EMERGENCY_PARSER.
  2214. *
  2215. * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  2216. */
  2217. //#define ADVANCED_PAUSE_FEATURE
  2218. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  2219. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
  2220. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
  2221. // This short retract is done immediately, before parking the nozzle.
  2222. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
  2223. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  2224. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
  2225. // For Bowden, the full length of the tube and nozzle.
  2226. // For direct drive, the full length of the nozzle.
  2227. // Set to 0 for manual unloading.
  2228. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
  2229. #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
  2230. // 0 to disable start loading and skip to fast load only
  2231. #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
  2232. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  2233. #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
  2234. // For Bowden, the full length of the tube and nozzle.
  2235. // For direct drive, the full length of the nozzle.
  2236. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
  2237. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
  2238. #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
  2239. // Set to 0 for manual extrusion.
  2240. // Filament can be extruded repeatedly from the Filament Change menu
  2241. // until extrusion is consistent, and to purge old filament.
  2242. #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
  2243. //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
  2244. // Filament Unload does a Retract, Delay, and Purge first:
  2245. #define FILAMENT_UNLOAD_PURGE_RETRACT 13 // (mm) Unload initial retract length.
  2246. #define FILAMENT_UNLOAD_PURGE_DELAY 5000 // (ms) Delay for the filament to cool after retract.
  2247. #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
  2248. #define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload
  2249. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
  2250. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
  2251. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
  2252. //#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again.
  2253. //#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing.
  2254. //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
  2255. //#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
  2256. //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
  2257. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
  2258. #endif
  2259. // @section tmc
  2260. /**
  2261. * TMC26X Stepper Driver options
  2262. *
  2263. * The TMC26XStepper library is required for this stepper driver.
  2264. * https://github.com/trinamic/TMC26XStepper
  2265. */
  2266. #if HAS_DRIVER(TMC26X)
  2267. #if AXIS_DRIVER_TYPE_X(TMC26X)
  2268. #define X_MAX_CURRENT 1000 // (mA)
  2269. #define X_SENSE_RESISTOR 91 // (mOhms)
  2270. #define X_MICROSTEPS 16 // Number of microsteps
  2271. #endif
  2272. #if AXIS_DRIVER_TYPE_X2(TMC26X)
  2273. #define X2_MAX_CURRENT 1000
  2274. #define X2_SENSE_RESISTOR 91
  2275. #define X2_MICROSTEPS X_MICROSTEPS
  2276. #endif
  2277. #if AXIS_DRIVER_TYPE_Y(TMC26X)
  2278. #define Y_MAX_CURRENT 1000
  2279. #define Y_SENSE_RESISTOR 91
  2280. #define Y_MICROSTEPS 16
  2281. #endif
  2282. #if AXIS_DRIVER_TYPE_Y2(TMC26X)
  2283. #define Y2_MAX_CURRENT 1000
  2284. #define Y2_SENSE_RESISTOR 91
  2285. #define Y2_MICROSTEPS Y_MICROSTEPS
  2286. #endif
  2287. #if AXIS_DRIVER_TYPE_Z(TMC26X)
  2288. #define Z_MAX_CURRENT 1000
  2289. #define Z_SENSE_RESISTOR 91
  2290. #define Z_MICROSTEPS 16
  2291. #endif
  2292. #if AXIS_DRIVER_TYPE_Z2(TMC26X)
  2293. #define Z2_MAX_CURRENT 1000
  2294. #define Z2_SENSE_RESISTOR 91
  2295. #define Z2_MICROSTEPS Z_MICROSTEPS
  2296. #endif
  2297. #if AXIS_DRIVER_TYPE_Z3(TMC26X)
  2298. #define Z3_MAX_CURRENT 1000
  2299. #define Z3_SENSE_RESISTOR 91
  2300. #define Z3_MICROSTEPS Z_MICROSTEPS
  2301. #endif
  2302. #if AXIS_DRIVER_TYPE_Z4(TMC26X)
  2303. #define Z4_MAX_CURRENT 1000
  2304. #define Z4_SENSE_RESISTOR 91
  2305. #define Z4_MICROSTEPS Z_MICROSTEPS
  2306. #endif
  2307. #if AXIS_DRIVER_TYPE_I(TMC26X)
  2308. #define I_MAX_CURRENT 1000
  2309. #define I_SENSE_RESISTOR 91
  2310. #define I_MICROSTEPS 16
  2311. #endif
  2312. #if AXIS_DRIVER_TYPE_J(TMC26X)
  2313. #define J_MAX_CURRENT 1000
  2314. #define J_SENSE_RESISTOR 91
  2315. #define J_MICROSTEPS 16
  2316. #endif
  2317. #if AXIS_DRIVER_TYPE_K(TMC26X)
  2318. #define K_MAX_CURRENT 1000
  2319. #define K_SENSE_RESISTOR 91
  2320. #define K_MICROSTEPS 16
  2321. #endif
  2322. #if AXIS_DRIVER_TYPE_U(TMC26X)
  2323. #define U_MAX_CURRENT 1000
  2324. #define U_SENSE_RESISTOR 91
  2325. #define U_MICROSTEPS 16
  2326. #endif
  2327. #if AXIS_DRIVER_TYPE_V(TMC26X)
  2328. #define V_MAX_CURRENT 1000
  2329. #define V_SENSE_RESISTOR 91
  2330. #define V_MICROSTEPS 16
  2331. #endif
  2332. #if AXIS_DRIVER_TYPE_W(TMC26X)
  2333. #define W_MAX_CURRENT 1000
  2334. #define W_SENSE_RESISTOR 91
  2335. #define W_MICROSTEPS 16
  2336. #endif
  2337. #if AXIS_DRIVER_TYPE_E0(TMC26X)
  2338. #define E0_MAX_CURRENT 1000
  2339. #define E0_SENSE_RESISTOR 91
  2340. #define E0_MICROSTEPS 16
  2341. #endif
  2342. #if AXIS_DRIVER_TYPE_E1(TMC26X)
  2343. #define E1_MAX_CURRENT 1000
  2344. #define E1_SENSE_RESISTOR 91
  2345. #define E1_MICROSTEPS E0_MICROSTEPS
  2346. #endif
  2347. #if AXIS_DRIVER_TYPE_E2(TMC26X)
  2348. #define E2_MAX_CURRENT 1000
  2349. #define E2_SENSE_RESISTOR 91
  2350. #define E2_MICROSTEPS E0_MICROSTEPS
  2351. #endif
  2352. #if AXIS_DRIVER_TYPE_E3(TMC26X)
  2353. #define E3_MAX_CURRENT 1000
  2354. #define E3_SENSE_RESISTOR 91
  2355. #define E3_MICROSTEPS E0_MICROSTEPS
  2356. #endif
  2357. #if AXIS_DRIVER_TYPE_E4(TMC26X)
  2358. #define E4_MAX_CURRENT 1000
  2359. #define E4_SENSE_RESISTOR 91
  2360. #define E4_MICROSTEPS E0_MICROSTEPS
  2361. #endif
  2362. #if AXIS_DRIVER_TYPE_E5(TMC26X)
  2363. #define E5_MAX_CURRENT 1000
  2364. #define E5_SENSE_RESISTOR 91
  2365. #define E5_MICROSTEPS E0_MICROSTEPS
  2366. #endif
  2367. #if AXIS_DRIVER_TYPE_E6(TMC26X)
  2368. #define E6_MAX_CURRENT 1000
  2369. #define E6_SENSE_RESISTOR 91
  2370. #define E6_MICROSTEPS E0_MICROSTEPS
  2371. #endif
  2372. #if AXIS_DRIVER_TYPE_E7(TMC26X)
  2373. #define E7_MAX_CURRENT 1000
  2374. #define E7_SENSE_RESISTOR 91
  2375. #define E7_MICROSTEPS E0_MICROSTEPS
  2376. #endif
  2377. #endif // TMC26X
  2378. // @section tmc_smart
  2379. /**
  2380. * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode
  2381. * connect your SPI pins to the hardware SPI interface on your board and define
  2382. * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3
  2383. * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  2384. * You may also use software SPI if you wish to use general purpose IO pins.
  2385. *
  2386. * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN
  2387. * to the driver side PDN_UART pin with a 1K resistor.
  2388. * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without
  2389. * a resistor.
  2390. * The drivers can also be used with hardware serial.
  2391. *
  2392. * TMCStepper library is required to use TMC stepper drivers.
  2393. * https://github.com/teemuatlut/TMCStepper
  2394. */
  2395. #if HAS_TRINAMIC_CONFIG
  2396. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  2397. /**
  2398. * Interpolate microsteps to 256
  2399. * Override for each driver with <driver>_INTERPOLATE settings below
  2400. */
  2401. #define INTERPOLATE true
  2402. #if AXIS_IS_TMC(X)
  2403. #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current.
  2404. #define X_CURRENT_HOME X_CURRENT // (mA) RMS current for sensorless homing
  2405. #define X_MICROSTEPS 16 // 0..256
  2406. #define X_RSENSE 0.11
  2407. #define X_CHAIN_POS -1 // -1..0: Not chained. 1: MCU MOSI connected. 2: Next in chain, ...
  2408. //#define X_INTERPOLATE true // Enable to override 'INTERPOLATE' for the X axis
  2409. //#define X_HOLD_MULTIPLIER 0.5 // Enable to override 'HOLD_MULTIPLIER' for the X axis
  2410. #endif
  2411. #if AXIS_IS_TMC(X2)
  2412. #define X2_CURRENT 800
  2413. #define X2_CURRENT_HOME X2_CURRENT
  2414. #define X2_MICROSTEPS X_MICROSTEPS
  2415. #define X2_RSENSE 0.11
  2416. #define X2_CHAIN_POS -1
  2417. //#define X2_INTERPOLATE true
  2418. //#define X2_HOLD_MULTIPLIER 0.5
  2419. #endif
  2420. #if AXIS_IS_TMC(Y)
  2421. #define Y_CURRENT 800
  2422. #define Y_CURRENT_HOME Y_CURRENT
  2423. #define Y_MICROSTEPS 16
  2424. #define Y_RSENSE 0.11
  2425. #define Y_CHAIN_POS -1
  2426. //#define Y_INTERPOLATE true
  2427. //#define Y_HOLD_MULTIPLIER 0.5
  2428. #endif
  2429. #if AXIS_IS_TMC(Y2)
  2430. #define Y2_CURRENT 800
  2431. #define Y2_CURRENT_HOME Y2_CURRENT
  2432. #define Y2_MICROSTEPS Y_MICROSTEPS
  2433. #define Y2_RSENSE 0.11
  2434. #define Y2_CHAIN_POS -1
  2435. //#define Y2_INTERPOLATE true
  2436. //#define Y2_HOLD_MULTIPLIER 0.5
  2437. #endif
  2438. #if AXIS_IS_TMC(Z)
  2439. #define Z_CURRENT 800
  2440. #define Z_CURRENT_HOME Z_CURRENT
  2441. #define Z_MICROSTEPS 16
  2442. #define Z_RSENSE 0.11
  2443. #define Z_CHAIN_POS -1
  2444. //#define Z_INTERPOLATE true
  2445. //#define Z_HOLD_MULTIPLIER 0.5
  2446. #endif
  2447. #if AXIS_IS_TMC(Z2)
  2448. #define Z2_CURRENT 800
  2449. #define Z2_CURRENT_HOME Z2_CURRENT
  2450. #define Z2_MICROSTEPS Z_MICROSTEPS
  2451. #define Z2_RSENSE 0.11
  2452. #define Z2_CHAIN_POS -1
  2453. //#define Z2_INTERPOLATE true
  2454. //#define Z2_HOLD_MULTIPLIER 0.5
  2455. #endif
  2456. #if AXIS_IS_TMC(Z3)
  2457. #define Z3_CURRENT 800
  2458. #define Z3_CURRENT_HOME Z3_CURRENT
  2459. #define Z3_MICROSTEPS Z_MICROSTEPS
  2460. #define Z3_RSENSE 0.11
  2461. #define Z3_CHAIN_POS -1
  2462. //#define Z3_INTERPOLATE true
  2463. //#define Z3_HOLD_MULTIPLIER 0.5
  2464. #endif
  2465. #if AXIS_IS_TMC(Z4)
  2466. #define Z4_CURRENT 800
  2467. #define Z4_CURRENT_HOME Z4_CURRENT
  2468. #define Z4_MICROSTEPS Z_MICROSTEPS
  2469. #define Z4_RSENSE 0.11
  2470. #define Z4_CHAIN_POS -1
  2471. //#define Z4_INTERPOLATE true
  2472. //#define Z4_HOLD_MULTIPLIER 0.5
  2473. #endif
  2474. #if AXIS_IS_TMC(I)
  2475. #define I_CURRENT 800
  2476. #define I_CURRENT_HOME I_CURRENT
  2477. #define I_MICROSTEPS 16
  2478. #define I_RSENSE 0.11
  2479. #define I_CHAIN_POS -1
  2480. //#define I_INTERPOLATE true
  2481. //#define I_HOLD_MULTIPLIER 0.5
  2482. #endif
  2483. #if AXIS_IS_TMC(J)
  2484. #define J_CURRENT 800
  2485. #define J_CURRENT_HOME J_CURRENT
  2486. #define J_MICROSTEPS 16
  2487. #define J_RSENSE 0.11
  2488. #define J_CHAIN_POS -1
  2489. //#define J_INTERPOLATE true
  2490. //#define J_HOLD_MULTIPLIER 0.5
  2491. #endif
  2492. #if AXIS_IS_TMC(K)
  2493. #define K_CURRENT 800
  2494. #define K_CURRENT_HOME K_CURRENT
  2495. #define K_MICROSTEPS 16
  2496. #define K_RSENSE 0.11
  2497. #define K_CHAIN_POS -1
  2498. //#define K_INTERPOLATE true
  2499. //#define K_HOLD_MULTIPLIER 0.5
  2500. #endif
  2501. #if AXIS_IS_TMC(U)
  2502. #define U_CURRENT 800
  2503. #define U_CURRENT_HOME U_CURRENT
  2504. #define U_MICROSTEPS 8
  2505. #define U_RSENSE 0.11
  2506. #define U_CHAIN_POS -1
  2507. //#define U_INTERPOLATE true
  2508. //#define U_HOLD_MULTIPLIER 0.5
  2509. #endif
  2510. #if AXIS_IS_TMC(V)
  2511. #define V_CURRENT 800
  2512. #define V_CURRENT_HOME V_CURRENT
  2513. #define V_MICROSTEPS 8
  2514. #define V_RSENSE 0.11
  2515. #define V_CHAIN_POS -1
  2516. //#define V_INTERPOLATE true
  2517. //#define V_HOLD_MULTIPLIER 0.5
  2518. #endif
  2519. #if AXIS_IS_TMC(W)
  2520. #define W_CURRENT 800
  2521. #define W_CURRENT_HOME W_CURRENT
  2522. #define W_MICROSTEPS 8
  2523. #define W_RSENSE 0.11
  2524. #define W_CHAIN_POS -1
  2525. //#define W_INTERPOLATE true
  2526. //#define W_HOLD_MULTIPLIER 0.5
  2527. #endif
  2528. #if AXIS_IS_TMC(E0)
  2529. #define E0_CURRENT 800
  2530. #define E0_MICROSTEPS 16
  2531. #define E0_RSENSE 0.11
  2532. #define E0_CHAIN_POS -1
  2533. //#define E0_INTERPOLATE true
  2534. //#define E0_HOLD_MULTIPLIER 0.5
  2535. #endif
  2536. #if AXIS_IS_TMC(E1)
  2537. #define E1_CURRENT 800
  2538. #define E1_MICROSTEPS E0_MICROSTEPS
  2539. #define E1_RSENSE 0.11
  2540. #define E1_CHAIN_POS -1
  2541. //#define E1_INTERPOLATE true
  2542. //#define E1_HOLD_MULTIPLIER 0.5
  2543. #endif
  2544. #if AXIS_IS_TMC(E2)
  2545. #define E2_CURRENT 800
  2546. #define E2_MICROSTEPS E0_MICROSTEPS
  2547. #define E2_RSENSE 0.11
  2548. #define E2_CHAIN_POS -1
  2549. //#define E2_INTERPOLATE true
  2550. //#define E2_HOLD_MULTIPLIER 0.5
  2551. #endif
  2552. #if AXIS_IS_TMC(E3)
  2553. #define E3_CURRENT 800
  2554. #define E3_MICROSTEPS E0_MICROSTEPS
  2555. #define E3_RSENSE 0.11
  2556. #define E3_CHAIN_POS -1
  2557. //#define E3_INTERPOLATE true
  2558. //#define E3_HOLD_MULTIPLIER 0.5
  2559. #endif
  2560. #if AXIS_IS_TMC(E4)
  2561. #define E4_CURRENT 800
  2562. #define E4_MICROSTEPS E0_MICROSTEPS
  2563. #define E4_RSENSE 0.11
  2564. #define E4_CHAIN_POS -1
  2565. //#define E4_INTERPOLATE true
  2566. //#define E4_HOLD_MULTIPLIER 0.5
  2567. #endif
  2568. #if AXIS_IS_TMC(E5)
  2569. #define E5_CURRENT 800
  2570. #define E5_MICROSTEPS E0_MICROSTEPS
  2571. #define E5_RSENSE 0.11
  2572. #define E5_CHAIN_POS -1
  2573. //#define E5_INTERPOLATE true
  2574. //#define E5_HOLD_MULTIPLIER 0.5
  2575. #endif
  2576. #if AXIS_IS_TMC(E6)
  2577. #define E6_CURRENT 800
  2578. #define E6_MICROSTEPS E0_MICROSTEPS
  2579. #define E6_RSENSE 0.11
  2580. #define E6_CHAIN_POS -1
  2581. //#define E6_INTERPOLATE true
  2582. //#define E6_HOLD_MULTIPLIER 0.5
  2583. #endif
  2584. #if AXIS_IS_TMC(E7)
  2585. #define E7_CURRENT 800
  2586. #define E7_MICROSTEPS E0_MICROSTEPS
  2587. #define E7_RSENSE 0.11
  2588. #define E7_CHAIN_POS -1
  2589. //#define E7_INTERPOLATE true
  2590. //#define E7_HOLD_MULTIPLIER 0.5
  2591. #endif
  2592. /**
  2593. * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here.
  2594. * The default pins can be found in your board's pins file.
  2595. */
  2596. //#define X_CS_PIN -1
  2597. //#define Y_CS_PIN -1
  2598. //#define Z_CS_PIN -1
  2599. //#define X2_CS_PIN -1
  2600. //#define Y2_CS_PIN -1
  2601. //#define Z2_CS_PIN -1
  2602. //#define Z3_CS_PIN -1
  2603. //#define Z4_CS_PIN -1
  2604. //#define I_CS_PIN -1
  2605. //#define J_CS_PIN -1
  2606. //#define K_CS_PIN -1
  2607. //#define U_CS_PIN -1
  2608. //#define V_CS_PIN -1
  2609. //#define W_CS_PIN -1
  2610. //#define E0_CS_PIN -1
  2611. //#define E1_CS_PIN -1
  2612. //#define E2_CS_PIN -1
  2613. //#define E3_CS_PIN -1
  2614. //#define E4_CS_PIN -1
  2615. //#define E5_CS_PIN -1
  2616. //#define E6_CS_PIN -1
  2617. //#define E7_CS_PIN -1
  2618. /**
  2619. * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160).
  2620. * The default SW SPI pins are defined the respective pins files,
  2621. * but you can override or define them here.
  2622. */
  2623. //#define TMC_USE_SW_SPI
  2624. //#define TMC_SW_MOSI -1
  2625. //#define TMC_SW_MISO -1
  2626. //#define TMC_SW_SCK -1
  2627. /**
  2628. * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses.
  2629. * Set the address using jumpers on pins MS1 and MS2.
  2630. * Address | MS1 | MS2
  2631. * 0 | LOW | LOW
  2632. * 1 | HIGH | LOW
  2633. * 2 | LOW | HIGH
  2634. * 3 | HIGH | HIGH
  2635. *
  2636. * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers
  2637. * on the same serial port, either here or in your board's pins file.
  2638. */
  2639. //#define X_SLAVE_ADDRESS 0
  2640. //#define Y_SLAVE_ADDRESS 0
  2641. //#define Z_SLAVE_ADDRESS 0
  2642. //#define X2_SLAVE_ADDRESS 0
  2643. //#define Y2_SLAVE_ADDRESS 0
  2644. //#define Z2_SLAVE_ADDRESS 0
  2645. //#define Z3_SLAVE_ADDRESS 0
  2646. //#define Z4_SLAVE_ADDRESS 0
  2647. //#define I_SLAVE_ADDRESS 0
  2648. //#define J_SLAVE_ADDRESS 0
  2649. //#define K_SLAVE_ADDRESS 0
  2650. //#define U_SLAVE_ADDRESS 0
  2651. //#define V_SLAVE_ADDRESS 0
  2652. //#define W_SLAVE_ADDRESS 0
  2653. //#define E0_SLAVE_ADDRESS 0
  2654. //#define E1_SLAVE_ADDRESS 0
  2655. //#define E2_SLAVE_ADDRESS 0
  2656. //#define E3_SLAVE_ADDRESS 0
  2657. //#define E4_SLAVE_ADDRESS 0
  2658. //#define E5_SLAVE_ADDRESS 0
  2659. //#define E6_SLAVE_ADDRESS 0
  2660. //#define E7_SLAVE_ADDRESS 0
  2661. /**
  2662. * Software enable
  2663. *
  2664. * Use for drivers that do not use a dedicated enable pin, but rather handle the same
  2665. * function through a communication line such as SPI or UART.
  2666. */
  2667. //#define SOFTWARE_DRIVER_ENABLE
  2668. /**
  2669. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  2670. * Use Trinamic's ultra quiet stepping mode.
  2671. * When disabled, Marlin will use spreadCycle stepping mode.
  2672. */
  2673. #define STEALTHCHOP_XY
  2674. #define STEALTHCHOP_Z
  2675. #define STEALTHCHOP_I
  2676. #define STEALTHCHOP_J
  2677. #define STEALTHCHOP_K
  2678. #define STEALTHCHOP_U
  2679. #define STEALTHCHOP_V
  2680. #define STEALTHCHOP_W
  2681. #define STEALTHCHOP_E
  2682. /**
  2683. * Optimize spreadCycle chopper parameters by using predefined parameter sets
  2684. * or with the help of an example included in the library.
  2685. * Provided parameter sets are
  2686. * CHOPPER_DEFAULT_12V
  2687. * CHOPPER_DEFAULT_19V
  2688. * CHOPPER_DEFAULT_24V
  2689. * CHOPPER_DEFAULT_36V
  2690. * CHOPPER_09STEP_24V // 0.9 degree steppers (24V)
  2691. * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Průša firmware for MK3 (24V)
  2692. * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9
  2693. *
  2694. * Define your own with:
  2695. * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
  2696. */
  2697. #define CHOPPER_TIMING CHOPPER_DEFAULT_12V // All axes (override below)
  2698. //#define CHOPPER_TIMING_X CHOPPER_TIMING // For X Axes (override below)
  2699. //#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X
  2700. //#define CHOPPER_TIMING_Y CHOPPER_TIMING // For Y Axes (override below)
  2701. //#define CHOPPER_TIMING_Y2 CHOPPER_TIMING_Y
  2702. //#define CHOPPER_TIMING_Z CHOPPER_TIMING // For Z Axes (override below)
  2703. //#define CHOPPER_TIMING_Z2 CHOPPER_TIMING_Z
  2704. //#define CHOPPER_TIMING_Z3 CHOPPER_TIMING_Z
  2705. //#define CHOPPER_TIMING_Z4 CHOPPER_TIMING_Z
  2706. //#define CHOPPER_TIMING_I CHOPPER_TIMING // For I Axis
  2707. //#define CHOPPER_TIMING_J CHOPPER_TIMING // For J Axis
  2708. //#define CHOPPER_TIMING_K CHOPPER_TIMING // For K Axis
  2709. //#define CHOPPER_TIMING_U CHOPPER_TIMING // For U Axis
  2710. //#define CHOPPER_TIMING_V CHOPPER_TIMING // For V Axis
  2711. //#define CHOPPER_TIMING_W CHOPPER_TIMING // For W Axis
  2712. //#define CHOPPER_TIMING_E CHOPPER_TIMING // For Extruders (override below)
  2713. //#define CHOPPER_TIMING_E1 CHOPPER_TIMING_E
  2714. //#define CHOPPER_TIMING_E2 CHOPPER_TIMING_E
  2715. //#define CHOPPER_TIMING_E3 CHOPPER_TIMING_E
  2716. //#define CHOPPER_TIMING_E4 CHOPPER_TIMING_E
  2717. //#define CHOPPER_TIMING_E5 CHOPPER_TIMING_E
  2718. //#define CHOPPER_TIMING_E6 CHOPPER_TIMING_E
  2719. //#define CHOPPER_TIMING_E7 CHOPPER_TIMING_E
  2720. /**
  2721. * Monitor Trinamic drivers
  2722. * for error conditions like overtemperature and short to ground.
  2723. * To manage over-temp Marlin can decrease the driver current until the error condition clears.
  2724. * Other detected conditions can be used to stop the current print.
  2725. * Relevant G-codes:
  2726. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  2727. * M911 - Report stepper driver overtemperature pre-warn condition.
  2728. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  2729. * M122 - Report driver parameters (Requires TMC_DEBUG)
  2730. */
  2731. //#define MONITOR_DRIVER_STATUS
  2732. #if ENABLED(MONITOR_DRIVER_STATUS)
  2733. #define CURRENT_STEP_DOWN 50 // [mA]
  2734. #define REPORT_CURRENT_CHANGE
  2735. #define STOP_ON_ERROR
  2736. #endif
  2737. /**
  2738. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  2739. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  2740. * This mode allows for faster movements at the expense of higher noise levels.
  2741. * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
  2742. * M913 X/Y/Z/E to live tune the setting
  2743. */
  2744. //#define HYBRID_THRESHOLD
  2745. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  2746. #define X2_HYBRID_THRESHOLD 100
  2747. #define Y_HYBRID_THRESHOLD 100
  2748. #define Y2_HYBRID_THRESHOLD 100
  2749. #define Z_HYBRID_THRESHOLD 3
  2750. #define Z2_HYBRID_THRESHOLD 3
  2751. #define Z3_HYBRID_THRESHOLD 3
  2752. #define Z4_HYBRID_THRESHOLD 3
  2753. #define I_HYBRID_THRESHOLD 3 // [linear=mm/s, rotational=°/s]
  2754. #define J_HYBRID_THRESHOLD 3 // [linear=mm/s, rotational=°/s]
  2755. #define K_HYBRID_THRESHOLD 3 // [linear=mm/s, rotational=°/s]
  2756. #define U_HYBRID_THRESHOLD 3 // [mm/s]
  2757. #define V_HYBRID_THRESHOLD 3
  2758. #define W_HYBRID_THRESHOLD 3
  2759. #define E0_HYBRID_THRESHOLD 30
  2760. #define E1_HYBRID_THRESHOLD 30
  2761. #define E2_HYBRID_THRESHOLD 30
  2762. #define E3_HYBRID_THRESHOLD 30
  2763. #define E4_HYBRID_THRESHOLD 30
  2764. #define E5_HYBRID_THRESHOLD 30
  2765. #define E6_HYBRID_THRESHOLD 30
  2766. #define E7_HYBRID_THRESHOLD 30
  2767. /**
  2768. * Use StallGuard to home / probe X, Y, Z.
  2769. *
  2770. * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
  2771. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
  2772. * X, Y, and Z homing will always be done in spreadCycle mode.
  2773. *
  2774. * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
  2775. * Use M914 X Y Z to set the stall threshold at runtime:
  2776. *
  2777. * Sensitivity TMC2209 Others
  2778. * HIGHEST 255 -64 (Too sensitive => False positive)
  2779. * LOWEST 0 63 (Too insensitive => No trigger)
  2780. *
  2781. * It is recommended to set HOMING_BUMP_MM to { 0, 0, 0 }.
  2782. *
  2783. * SPI_ENDSTOPS *** Beta feature! *** TMC2130/TMC5160 Only ***
  2784. * Poll the driver through SPI to determine load when homing.
  2785. * Removes the need for a wire from DIAG1 to an endstop pin.
  2786. *
  2787. * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
  2788. * homing and adds a guard period for endstop triggering.
  2789. *
  2790. * Comment *_STALL_SENSITIVITY to disable sensorless homing for that axis.
  2791. */
  2792. //#define SENSORLESS_HOMING // StallGuard capable drivers only
  2793. #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
  2794. // TMC2209: 0...255. TMC2130: -64...63
  2795. #define X_STALL_SENSITIVITY 8
  2796. #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
  2797. #define Y_STALL_SENSITIVITY 8
  2798. #define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
  2799. //#define Z_STALL_SENSITIVITY 8
  2800. //#define Z2_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2801. //#define Z3_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2802. //#define Z4_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2803. //#define I_STALL_SENSITIVITY 8
  2804. //#define J_STALL_SENSITIVITY 8
  2805. //#define K_STALL_SENSITIVITY 8
  2806. //#define U_STALL_SENSITIVITY 8
  2807. //#define V_STALL_SENSITIVITY 8
  2808. //#define W_STALL_SENSITIVITY 8
  2809. //#define SPI_ENDSTOPS // TMC2130 only
  2810. //#define IMPROVE_HOMING_RELIABILITY
  2811. #endif
  2812. /**
  2813. * TMC Homing stepper phase.
  2814. *
  2815. * Improve homing repeatability by homing to stepper coil's nearest absolute
  2816. * phase position. Trinamic drivers use a stepper phase table with 1024 values
  2817. * spanning 4 full steps with 256 positions each (ergo, 1024 positions).
  2818. * Full step positions (128, 384, 640, 896) have the highest holding torque.
  2819. *
  2820. * Values from 0..1023, -1 to disable homing phase for that axis.
  2821. */
  2822. //#define TMC_HOME_PHASE { 896, 896, 896 }
  2823. /**
  2824. * Beta feature!
  2825. * Create a 50/50 square wave step pulse optimal for stepper drivers.
  2826. */
  2827. //#define SQUARE_WAVE_STEPPING
  2828. /**
  2829. * Enable M122 debugging command for TMC stepper drivers.
  2830. * M122 S0/1 will enable continuous reporting.
  2831. */
  2832. //#define TMC_DEBUG
  2833. /**
  2834. * You can set your own advanced settings by filling in predefined functions.
  2835. * A list of available functions can be found on the library github page
  2836. * https://github.com/teemuatlut/TMCStepper
  2837. *
  2838. * Example:
  2839. * #define TMC_ADV() { \
  2840. * stepperX.diag0_otpw(1); \
  2841. * stepperY.intpol(0); \
  2842. * }
  2843. */
  2844. #define TMC_ADV() { }
  2845. #endif // HAS_TRINAMIC_CONFIG
  2846. // @section L64XX
  2847. /**
  2848. * L64XX Stepper Driver options
  2849. *
  2850. * Arduino-L6470 library (0.8.0 or higher) is required.
  2851. * https://github.com/ameyer/Arduino-L6470
  2852. *
  2853. * Requires the following to be defined in your pins_YOUR_BOARD file
  2854. * L6470_CHAIN_SCK_PIN
  2855. * L6470_CHAIN_MISO_PIN
  2856. * L6470_CHAIN_MOSI_PIN
  2857. * L6470_CHAIN_SS_PIN
  2858. * ENABLE_RESET_L64XX_CHIPS(Q) where Q is 1 to enable and 0 to reset
  2859. */
  2860. #if HAS_L64XX
  2861. //#define L6470_CHITCHAT // Display additional status info
  2862. #if AXIS_IS_L64XX(X)
  2863. #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) - L6474 max is 16
  2864. #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current
  2865. // L6470 & L6474 - VALID: 375 x (1 - 16) - 6A max - rounds down
  2866. // POWERSTEP01: VALID: 1000 x (1 - 32) - 32A max - rounds down
  2867. #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down)
  2868. // L6470 & L6474 - VALID: 31.25 * (1-128) - 4A max - rounds down
  2869. // POWERSTEP01: VALID: 200 x (1 - 32) - 6.4A max - rounds down
  2870. // L6474 - STALLCURRENT setting is used to set the nominal (TVAL) current
  2871. #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper - not used by L6474
  2872. #define X_CHAIN_POS -1 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI
  2873. #define X_SLEW_RATE 1 // 0-3, Slew 0 is slowest, 3 is fastest
  2874. #endif
  2875. #if AXIS_IS_L64XX(X2)
  2876. #define X2_MICROSTEPS X_MICROSTEPS
  2877. #define X2_OVERCURRENT 2000
  2878. #define X2_STALLCURRENT 1500
  2879. #define X2_MAX_VOLTAGE 127
  2880. #define X2_CHAIN_POS -1
  2881. #define X2_SLEW_RATE 1
  2882. #endif
  2883. #if AXIS_IS_L64XX(Y)
  2884. #define Y_MICROSTEPS 128
  2885. #define Y_OVERCURRENT 2000
  2886. #define Y_STALLCURRENT 1500
  2887. #define Y_MAX_VOLTAGE 127
  2888. #define Y_CHAIN_POS -1
  2889. #define Y_SLEW_RATE 1
  2890. #endif
  2891. #if AXIS_IS_L64XX(Y2)
  2892. #define Y2_MICROSTEPS Y_MICROSTEPS
  2893. #define Y2_OVERCURRENT 2000
  2894. #define Y2_STALLCURRENT 1500
  2895. #define Y2_MAX_VOLTAGE 127
  2896. #define Y2_CHAIN_POS -1
  2897. #define Y2_SLEW_RATE 1
  2898. #endif
  2899. #if AXIS_IS_L64XX(Z)
  2900. #define Z_MICROSTEPS 128
  2901. #define Z_OVERCURRENT 2000
  2902. #define Z_STALLCURRENT 1500
  2903. #define Z_MAX_VOLTAGE 127
  2904. #define Z_CHAIN_POS -1
  2905. #define Z_SLEW_RATE 1
  2906. #endif
  2907. #if AXIS_IS_L64XX(Z2)
  2908. #define Z2_MICROSTEPS Z_MICROSTEPS
  2909. #define Z2_OVERCURRENT 2000
  2910. #define Z2_STALLCURRENT 1500
  2911. #define Z2_MAX_VOLTAGE 127
  2912. #define Z2_CHAIN_POS -1
  2913. #define Z2_SLEW_RATE 1
  2914. #endif
  2915. #if AXIS_IS_L64XX(Z3)
  2916. #define Z3_MICROSTEPS Z_MICROSTEPS
  2917. #define Z3_OVERCURRENT 2000
  2918. #define Z3_STALLCURRENT 1500
  2919. #define Z3_MAX_VOLTAGE 127
  2920. #define Z3_CHAIN_POS -1
  2921. #define Z3_SLEW_RATE 1
  2922. #endif
  2923. #if AXIS_IS_L64XX(Z4)
  2924. #define Z4_MICROSTEPS Z_MICROSTEPS
  2925. #define Z4_OVERCURRENT 2000
  2926. #define Z4_STALLCURRENT 1500
  2927. #define Z4_MAX_VOLTAGE 127
  2928. #define Z4_CHAIN_POS -1
  2929. #define Z4_SLEW_RATE 1
  2930. #endif
  2931. #if AXIS_IS_L64XX(I)
  2932. #define I_MICROSTEPS 128
  2933. #define I_OVERCURRENT 2000
  2934. #define I_STALLCURRENT 1500
  2935. #define I_MAX_VOLTAGE 127
  2936. #define I_CHAIN_POS -1
  2937. #define I_SLEW_RATE 1
  2938. #endif
  2939. #if AXIS_IS_L64XX(J)
  2940. #define J_MICROSTEPS 128
  2941. #define J_OVERCURRENT 2000
  2942. #define J_STALLCURRENT 1500
  2943. #define J_MAX_VOLTAGE 127
  2944. #define J_CHAIN_POS -1
  2945. #define J_SLEW_RATE 1
  2946. #endif
  2947. #if AXIS_IS_L64XX(K)
  2948. #define K_MICROSTEPS 128
  2949. #define K_OVERCURRENT 2000
  2950. #define K_STALLCURRENT 1500
  2951. #define K_MAX_VOLTAGE 127
  2952. #define K_CHAIN_POS -1
  2953. #define K_SLEW_RATE 1
  2954. #endif
  2955. #if AXIS_IS_L64XX(U)
  2956. #define U_MICROSTEPS 128
  2957. #define U_OVERCURRENT 2000
  2958. #define U_STALLCURRENT 1500
  2959. #define U_MAX_VOLTAGE 127
  2960. #define U_CHAIN_POS -1
  2961. #define U_SLEW_RATE 1
  2962. #endif
  2963. #if AXIS_IS_L64XX(V)
  2964. #define V_MICROSTEPS 128
  2965. #define V_OVERCURRENT 2000
  2966. #define V_STALLCURRENT 1500
  2967. #define V_MAX_VOLTAGE 127
  2968. #define V_CHAIN_POS -1
  2969. #define V_SLEW_RATE 1
  2970. #endif
  2971. #if AXIS_IS_L64XX(W)
  2972. #define W_MICROSTEPS 128
  2973. #define W_OVERCURRENT 2000
  2974. #define W_STALLCURRENT 1500
  2975. #define W_MAX_VOLTAGE 127
  2976. #define W_CHAIN_POS -1
  2977. #define W_SLEW_RATE 1
  2978. #endif
  2979. #if AXIS_IS_L64XX(E0)
  2980. #define E0_MICROSTEPS 128
  2981. #define E0_OVERCURRENT 2000
  2982. #define E0_STALLCURRENT 1500
  2983. #define E0_MAX_VOLTAGE 127
  2984. #define E0_CHAIN_POS -1
  2985. #define E0_SLEW_RATE 1
  2986. #endif
  2987. #if AXIS_IS_L64XX(E1)
  2988. #define E1_MICROSTEPS E0_MICROSTEPS
  2989. #define E1_OVERCURRENT 2000
  2990. #define E1_STALLCURRENT 1500
  2991. #define E1_MAX_VOLTAGE 127
  2992. #define E1_CHAIN_POS -1
  2993. #define E1_SLEW_RATE 1
  2994. #endif
  2995. #if AXIS_IS_L64XX(E2)
  2996. #define E2_MICROSTEPS E0_MICROSTEPS
  2997. #define E2_OVERCURRENT 2000
  2998. #define E2_STALLCURRENT 1500
  2999. #define E2_MAX_VOLTAGE 127
  3000. #define E2_CHAIN_POS -1
  3001. #define E2_SLEW_RATE 1
  3002. #endif
  3003. #if AXIS_IS_L64XX(E3)
  3004. #define E3_MICROSTEPS E0_MICROSTEPS
  3005. #define E3_OVERCURRENT 2000
  3006. #define E3_STALLCURRENT 1500
  3007. #define E3_MAX_VOLTAGE 127
  3008. #define E3_CHAIN_POS -1
  3009. #define E3_SLEW_RATE 1
  3010. #endif
  3011. #if AXIS_IS_L64XX(E4)
  3012. #define E4_MICROSTEPS E0_MICROSTEPS
  3013. #define E4_OVERCURRENT 2000
  3014. #define E4_STALLCURRENT 1500
  3015. #define E4_MAX_VOLTAGE 127
  3016. #define E4_CHAIN_POS -1
  3017. #define E4_SLEW_RATE 1
  3018. #endif
  3019. #if AXIS_IS_L64XX(E5)
  3020. #define E5_MICROSTEPS E0_MICROSTEPS
  3021. #define E5_OVERCURRENT 2000
  3022. #define E5_STALLCURRENT 1500
  3023. #define E5_MAX_VOLTAGE 127
  3024. #define E5_CHAIN_POS -1
  3025. #define E5_SLEW_RATE 1
  3026. #endif
  3027. #if AXIS_IS_L64XX(E6)
  3028. #define E6_MICROSTEPS E0_MICROSTEPS
  3029. #define E6_OVERCURRENT 2000
  3030. #define E6_STALLCURRENT 1500
  3031. #define E6_MAX_VOLTAGE 127
  3032. #define E6_CHAIN_POS -1
  3033. #define E6_SLEW_RATE 1
  3034. #endif
  3035. #if AXIS_IS_L64XX(E7)
  3036. #define E7_MICROSTEPS E0_MICROSTEPS
  3037. #define E7_OVERCURRENT 2000
  3038. #define E7_STALLCURRENT 1500
  3039. #define E7_MAX_VOLTAGE 127
  3040. #define E7_CHAIN_POS -1
  3041. #define E7_SLEW_RATE 1
  3042. #endif
  3043. /**
  3044. * Monitor L6470 drivers for error conditions like over temperature and over current.
  3045. * In the case of over temperature Marlin can decrease the drive until the error condition clears.
  3046. * Other detected conditions can be used to stop the current print.
  3047. * Relevant G-codes:
  3048. * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given.
  3049. * I not present or I0 or I1 - X, Y, Z or E0
  3050. * I2 - X2, Y2, Z2 or E1
  3051. * I3 - Z3 or E3
  3052. * I4 - Z4 or E4
  3053. * I5 - E5
  3054. * M916 - Increase drive level until get thermal warning
  3055. * M917 - Find minimum current thresholds
  3056. * M918 - Increase speed until max or error
  3057. * M122 S0/1 - Report driver parameters
  3058. */
  3059. //#define MONITOR_L6470_DRIVER_STATUS
  3060. #if ENABLED(MONITOR_L6470_DRIVER_STATUS)
  3061. #define KVAL_HOLD_STEP_DOWN 1
  3062. //#define L6470_STOP_ON_ERROR
  3063. #endif
  3064. #endif // HAS_L64XX
  3065. // @section i2cbus
  3066. //
  3067. // I2C Master ID for LPC176x LCD and Digital Current control
  3068. // Does not apply to other peripherals based on the Wire library.
  3069. //
  3070. //#define I2C_MASTER_ID 1 // Set a value from 0 to 2
  3071. /**
  3072. * TWI/I2C BUS
  3073. *
  3074. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  3075. * machines. Enabling this will allow you to send and receive I2C data from slave
  3076. * devices on the bus.
  3077. *
  3078. * ; Example #1
  3079. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  3080. * ; It uses multiple M260 commands with one B<base 10> arg
  3081. * M260 A99 ; Target slave address
  3082. * M260 B77 ; M
  3083. * M260 B97 ; a
  3084. * M260 B114 ; r
  3085. * M260 B108 ; l
  3086. * M260 B105 ; i
  3087. * M260 B110 ; n
  3088. * M260 S1 ; Send the current buffer
  3089. *
  3090. * ; Example #2
  3091. * ; Request 6 bytes from slave device with address 0x63 (99)
  3092. * M261 A99 B5
  3093. *
  3094. * ; Example #3
  3095. * ; Example serial output of a M261 request
  3096. * echo:i2c-reply: from:99 bytes:5 data:hello
  3097. */
  3098. //#define EXPERIMENTAL_I2CBUS
  3099. #if ENABLED(EXPERIMENTAL_I2CBUS)
  3100. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  3101. #endif
  3102. // @section extras
  3103. /**
  3104. * Photo G-code
  3105. * Add the M240 G-code to take a photo.
  3106. * The photo can be triggered by a digital pin or a physical movement.
  3107. */
  3108. //#define PHOTO_GCODE
  3109. #if ENABLED(PHOTO_GCODE)
  3110. // A position to move to (and raise Z) before taking the photo
  3111. //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z)
  3112. //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P)
  3113. //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S)
  3114. // Canon RC-1 or homebrew digital camera trigger
  3115. // Data from: https://www.doc-diy.net/photo/rc-1_hacked/
  3116. //#define PHOTOGRAPH_PIN 23
  3117. // Canon Hack Development Kit
  3118. // https://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  3119. //#define CHDK_PIN 4
  3120. // Optional second move with delay to trigger the camera shutter
  3121. //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J)
  3122. // Duration to hold the switch or keep CHDK_PIN high
  3123. //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D)
  3124. /**
  3125. * PHOTO_PULSES_US may need adjustment depending on board and camera model.
  3126. * Pin must be running at 48.4kHz.
  3127. * Be sure to use a PHOTOGRAPH_PIN which can rise and fall quick enough.
  3128. * (e.g., MKS SBase temp sensor pin was too slow, so used P1.23 on J8.)
  3129. *
  3130. * Example pulse data for Nikon: https://bit.ly/2FKD0Aq
  3131. * IR Wiring: https://git.io/JvJf7
  3132. */
  3133. //#define PHOTO_PULSES_US { 2000, 27850, 400, 1580, 400, 3580, 400 } // (µs) Durations for each 48.4kHz oscillation
  3134. #ifdef PHOTO_PULSES_US
  3135. #define PHOTO_PULSE_DELAY_US 13 // (µs) Approximate duration of each HIGH and LOW pulse in the oscillation
  3136. #endif
  3137. #endif
  3138. /**
  3139. * Spindle & Laser control
  3140. *
  3141. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  3142. * to set spindle speed, spindle direction, and laser power.
  3143. *
  3144. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  3145. * Marlin can be used to turn the spindle on and off. It can also be used to set
  3146. * the spindle speed from 5,000 to 30,000 RPM.
  3147. *
  3148. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  3149. * hardware PWM pin for the speed control and a pin for the rotation direction.
  3150. *
  3151. * See https://marlinfw.org/docs/configuration/2.0.9/laser_spindle.html for more config details.
  3152. */
  3153. //#define SPINDLE_FEATURE
  3154. //#define LASER_FEATURE
  3155. #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
  3156. #define SPINDLE_LASER_ACTIVE_STATE LOW // Set to "HIGH" if SPINDLE_LASER_ENA_PIN is active HIGH
  3157. #define SPINDLE_LASER_USE_PWM // Enable if your controller supports setting the speed/power
  3158. #if ENABLED(SPINDLE_LASER_USE_PWM)
  3159. #define SPINDLE_LASER_PWM_INVERT false // Set to "true" if the speed/power goes up when you want it to go slower
  3160. #define SPINDLE_LASER_FREQUENCY 2500 // (Hz) Spindle/laser frequency (only on supported HALs: AVR, ESP32, and LPC)
  3161. // ESP32: If SPINDLE_LASER_PWM_PIN is onboard then <=78125Hz. For I2S expander
  3162. // the frequency determines the PWM resolution. 2500Hz = 0-100, 977Hz = 0-255, ...
  3163. // (250000 / SPINDLE_LASER_FREQUENCY) = max value.
  3164. #endif
  3165. //#define AIR_EVACUATION // Cutter Vacuum / Laser Blower motor control with G-codes M10-M11
  3166. #if ENABLED(AIR_EVACUATION)
  3167. #define AIR_EVACUATION_ACTIVE LOW // Set to "HIGH" if the on/off function is active HIGH
  3168. //#define AIR_EVACUATION_PIN 42 // Override the default Cutter Vacuum or Laser Blower pin
  3169. #endif
  3170. //#define AIR_ASSIST // Air Assist control with G-codes M8-M9
  3171. #if ENABLED(AIR_ASSIST)
  3172. #define AIR_ASSIST_ACTIVE LOW // Active state on air assist pin
  3173. //#define AIR_ASSIST_PIN 44 // Override the default Air Assist pin
  3174. #endif
  3175. //#define SPINDLE_SERVO // A servo converting an angle to spindle power
  3176. #ifdef SPINDLE_SERVO
  3177. #define SPINDLE_SERVO_NR 0 // Index of servo used for spindle control
  3178. #define SPINDLE_SERVO_MIN 10 // Minimum angle for servo spindle
  3179. #endif
  3180. /**
  3181. * Speed / Power can be set ('M3 S') and displayed in terms of:
  3182. * - PWM255 (S0 - S255)
  3183. * - PERCENT (S0 - S100)
  3184. * - RPM (S0 - S50000) Best for use with a spindle
  3185. * - SERVO (S0 - S180)
  3186. */
  3187. #define CUTTER_POWER_UNIT PWM255
  3188. /**
  3189. * Relative Cutter Power
  3190. * Normally, 'M3 O<power>' sets
  3191. * OCR power is relative to the range SPEED_POWER_MIN...SPEED_POWER_MAX.
  3192. * so input powers of 0...255 correspond to SPEED_POWER_MIN...SPEED_POWER_MAX
  3193. * instead of normal range (0 to SPEED_POWER_MAX).
  3194. * Best used with (e.g.) SuperPID router controller: S0 = 5,000 RPM and S255 = 30,000 RPM
  3195. */
  3196. //#define CUTTER_POWER_RELATIVE // Set speed proportional to [SPEED_POWER_MIN...SPEED_POWER_MAX]
  3197. #if ENABLED(SPINDLE_FEATURE)
  3198. //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
  3199. #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
  3200. #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
  3201. #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
  3202. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
  3203. /**
  3204. * M3/M4 Power Equation
  3205. *
  3206. * Each tool uses different value ranges for speed / power control.
  3207. * These parameters are used to convert between tool power units and PWM.
  3208. *
  3209. * Speed/Power = (PWMDC / 255 * 100 - SPEED_POWER_INTERCEPT) / SPEED_POWER_SLOPE
  3210. * PWMDC = (spdpwr - SPEED_POWER_MIN) / (SPEED_POWER_MAX - SPEED_POWER_MIN) / SPEED_POWER_SLOPE
  3211. */
  3212. #if ENABLED(SPINDLE_LASER_USE_PWM)
  3213. #define SPEED_POWER_INTERCEPT 0 // (%) 0-100 i.e., Minimum power percentage
  3214. #define SPEED_POWER_MIN 5000 // (RPM)
  3215. #define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
  3216. #define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
  3217. #endif
  3218. #else
  3219. #if ENABLED(SPINDLE_LASER_USE_PWM)
  3220. #define SPEED_POWER_INTERCEPT 0 // (%) 0-100 i.e., Minimum power percentage
  3221. #define SPEED_POWER_MIN 0 // (%) 0-100
  3222. #define SPEED_POWER_MAX 100 // (%) 0-100
  3223. #define SPEED_POWER_STARTUP 80 // (%) M3/M4 speed/power default (with no arguments)
  3224. #endif
  3225. // Define the minimum and maximum test pulse time values for a laser test fire function
  3226. #define LASER_TEST_PULSE_MIN 1 // (ms) Used with Laser Control Menu
  3227. #define LASER_TEST_PULSE_MAX 999 // (ms) Caution: Menu may not show more than 3 characters
  3228. #define SPINDLE_LASER_POWERUP_DELAY 50 // (ms) Delay to allow the spindle/laser to come up to speed/power
  3229. #define SPINDLE_LASER_POWERDOWN_DELAY 50 // (ms) Delay to allow the spindle to stop
  3230. /**
  3231. * Laser Safety Timeout
  3232. *
  3233. * The laser should be turned off when there is no movement for a period of time.
  3234. * Consider material flammability, cut rate, and G-code order when setting this
  3235. * value. Too low and it could turn off during a very slow move; too high and
  3236. * the material could ignite.
  3237. */
  3238. #define LASER_SAFETY_TIMEOUT_MS 1000 // (ms)
  3239. /**
  3240. * Any M3 or G1/2/3/5 command with the 'I' parameter enables continuous inline power mode.
  3241. *
  3242. * e.g., 'M3 I' enables continuous inline power which is processed by the planner.
  3243. * Power is stored in move blocks and applied when blocks are processed by the Stepper ISR.
  3244. *
  3245. * 'M4 I' sets dynamic mode which uses the current feedrate to calculate a laser power OCR value.
  3246. *
  3247. * Any move in dynamic mode will use the current feedrate to calculate the laser power.
  3248. * Feed rates are set by the F parameter of a move command e.g. G1 X0 Y10 F6000
  3249. * Laser power would be calculated by bit shifting off 8 LSB's. In binary this is div 256.
  3250. * The calculation gives us ocr values from 0 to 255, values over F65535 will be set as 255 .
  3251. * More refined power control such as compesation for accell/decell will be addressed in future releases.
  3252. *
  3253. * M5 I clears inline mode and set power to 0, M5 sets the power output to 0 but leaves inline mode on.
  3254. */
  3255. /**
  3256. * Enable M3 commands for laser mode inline power planner syncing.
  3257. * This feature enables any M3 S-value to be injected into the block buffers while in
  3258. * CUTTER_MODE_CONTINUOUS. The option allows M3 laser power to be commited without waiting
  3259. * for a planner syncronization
  3260. */
  3261. //#define LASER_POWER_SYNC
  3262. /**
  3263. * Scale the laser's power in proportion to the movement rate.
  3264. *
  3265. * - Sets the entry power proportional to the entry speed over the nominal speed.
  3266. * - Ramps the power up every N steps to approximate the speed trapezoid.
  3267. * - Due to the limited power resolution this is only approximate.
  3268. */
  3269. //#define LASER_POWER_TRAP
  3270. //
  3271. // Laser I2C Ammeter (High precision INA226 low/high side module)
  3272. //
  3273. //#define I2C_AMMETER
  3274. #if ENABLED(I2C_AMMETER)
  3275. #define I2C_AMMETER_IMAX 0.1 // (Amps) Calibration value for the expected current range
  3276. #define I2C_AMMETER_SHUNT_RESISTOR 0.1 // (Ohms) Calibration shunt resistor value
  3277. #endif
  3278. //
  3279. // Laser Coolant Flow Meter
  3280. //
  3281. //#define LASER_COOLANT_FLOW_METER
  3282. #if ENABLED(LASER_COOLANT_FLOW_METER)
  3283. #define FLOWMETER_PIN 20 // Requires an external interrupt-enabled pin (e.g., RAMPS 2,3,18,19,20,21)
  3284. #define FLOWMETER_PPL 5880 // (pulses/liter) Flow meter pulses-per-liter on the input pin
  3285. #define FLOWMETER_INTERVAL 1000 // (ms) Flow rate calculation interval in milliseconds
  3286. #define FLOWMETER_SAFETY // Prevent running the laser without the minimum flow rate set below
  3287. #if ENABLED(FLOWMETER_SAFETY)
  3288. #define FLOWMETER_MIN_LITERS_PER_MINUTE 1.5 // (liters/min) Minimum flow required when enabled
  3289. #endif
  3290. #endif
  3291. #endif
  3292. #endif // SPINDLE_FEATURE || LASER_FEATURE
  3293. /**
  3294. * Synchronous Laser Control with M106/M107
  3295. *
  3296. * Marlin normally applies M106/M107 fan speeds at a time "soon after" processing
  3297. * a planner block. This is too inaccurate for a PWM/TTL laser attached to the fan
  3298. * header (as with some add-on laser kits). Enable this option to set fan/laser
  3299. * speeds with much more exact timing for improved print fidelity.
  3300. *
  3301. * NOTE: This option sacrifices some cooling fan speed options.
  3302. */
  3303. //#define LASER_SYNCHRONOUS_M106_M107
  3304. /**
  3305. * Coolant Control
  3306. *
  3307. * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off.
  3308. *
  3309. * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined.
  3310. */
  3311. //#define COOLANT_CONTROL
  3312. #if ENABLED(COOLANT_CONTROL)
  3313. #define COOLANT_MIST // Enable if mist coolant is present
  3314. #define COOLANT_FLOOD // Enable if flood coolant is present
  3315. #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed
  3316. #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed
  3317. #endif
  3318. /**
  3319. * Filament Width Sensor
  3320. *
  3321. * Measures the filament width in real-time and adjusts
  3322. * flow rate to compensate for any irregularities.
  3323. *
  3324. * Also allows the measured filament diameter to set the
  3325. * extrusion rate, so the slicer only has to specify the
  3326. * volume.
  3327. *
  3328. * Only a single extruder is supported at this time.
  3329. *
  3330. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  3331. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  3332. * 301 RAMBO : Analog input 3
  3333. *
  3334. * Note: May require analog pins to be defined for other boards.
  3335. */
  3336. //#define FILAMENT_WIDTH_SENSOR
  3337. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  3338. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
  3339. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  3340. #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it
  3341. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  3342. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  3343. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  3344. //#define FILAMENT_LCD_DISPLAY
  3345. #endif
  3346. /**
  3347. * Power Monitor
  3348. * Monitor voltage (V) and/or current (A), and -when possible- power (W)
  3349. *
  3350. * Read and configure with M430
  3351. *
  3352. * The current sensor feeds DC voltage (relative to the measured current) to an analog pin
  3353. * The voltage sensor feeds DC voltage (relative to the measured voltage) to an analog pin
  3354. */
  3355. //#define POWER_MONITOR_CURRENT // Monitor the system current
  3356. //#define POWER_MONITOR_VOLTAGE // Monitor the system voltage
  3357. #if ENABLED(POWER_MONITOR_CURRENT)
  3358. #define POWER_MONITOR_VOLTS_PER_AMP 0.05000 // Input voltage to the MCU analog pin per amp - DO NOT apply more than ADC_VREF!
  3359. #define POWER_MONITOR_CURRENT_OFFSET 0 // Offset (in amps) applied to the calculated current
  3360. #define POWER_MONITOR_FIXED_VOLTAGE 13.6 // Voltage for a current sensor with no voltage sensor (for power display)
  3361. #endif
  3362. #if ENABLED(POWER_MONITOR_VOLTAGE)
  3363. #define POWER_MONITOR_VOLTS_PER_VOLT 0.077933 // Input voltage to the MCU analog pin per volt - DO NOT apply more than ADC_VREF!
  3364. #define POWER_MONITOR_VOLTAGE_OFFSET 0 // Offset (in volts) applied to the calculated voltage
  3365. #endif
  3366. /**
  3367. * Stepper Driver Anti-SNAFU Protection
  3368. *
  3369. * If the SAFE_POWER_PIN is defined for your board, Marlin will check
  3370. * that stepper drivers are properly plugged in before applying power.
  3371. * Disable protection if your stepper drivers don't support the feature.
  3372. */
  3373. //#define DISABLE_DRIVER_SAFE_POWER_PROTECT
  3374. /**
  3375. * CNC Coordinate Systems
  3376. *
  3377. * Enables G53 and G54-G59.3 commands to select coordinate systems
  3378. * and G92.1 to reset the workspace to native machine space.
  3379. */
  3380. //#define CNC_COORDINATE_SYSTEMS
  3381. /**
  3382. * Auto-report fan speed with M123 S<seconds>
  3383. * Requires fans with tachometer pins
  3384. */
  3385. //#define AUTO_REPORT_FANS
  3386. /**
  3387. * Auto-report temperatures with M155 S<seconds>
  3388. */
  3389. #define AUTO_REPORT_TEMPERATURES
  3390. #if ENABLED(AUTO_REPORT_TEMPERATURES) && TEMP_SENSOR_REDUNDANT
  3391. //#define AUTO_REPORT_REDUNDANT // Include the "R" sensor in the auto-report
  3392. #endif
  3393. /**
  3394. * Auto-report position with M154 S<seconds>
  3395. */
  3396. //#define AUTO_REPORT_POSITION
  3397. /**
  3398. * Include capabilities in M115 output
  3399. */
  3400. #define EXTENDED_CAPABILITIES_REPORT
  3401. #if ENABLED(EXTENDED_CAPABILITIES_REPORT)
  3402. //#define M115_GEOMETRY_REPORT
  3403. #endif
  3404. /**
  3405. * Expected Printer Check
  3406. * Add the M16 G-code to compare a string to the MACHINE_NAME.
  3407. * M16 with a non-matching string causes the printer to halt.
  3408. */
  3409. //#define EXPECTED_PRINTER_CHECK
  3410. /**
  3411. * Disable all Volumetric extrusion options
  3412. */
  3413. //#define NO_VOLUMETRICS
  3414. #if DISABLED(NO_VOLUMETRICS)
  3415. /**
  3416. * Volumetric extrusion default state
  3417. * Activate to make volumetric extrusion the default method,
  3418. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  3419. *
  3420. * M200 D0 to disable, M200 Dn to set a new diameter (and enable volumetric).
  3421. * M200 S0/S1 to disable/enable volumetric extrusion.
  3422. */
  3423. //#define VOLUMETRIC_DEFAULT_ON
  3424. //#define VOLUMETRIC_EXTRUDER_LIMIT
  3425. #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT)
  3426. /**
  3427. * Default volumetric extrusion limit in cubic mm per second (mm^3/sec).
  3428. * This factory setting applies to all extruders.
  3429. * Use 'M200 [T<extruder>] L<limit>' to override and 'M502' to reset.
  3430. * A non-zero value activates Volume-based Extrusion Limiting.
  3431. */
  3432. #define DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT 0.00 // (mm^3/sec)
  3433. #endif
  3434. #endif
  3435. /**
  3436. * Enable this option for a leaner build of Marlin that removes all
  3437. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  3438. *
  3439. * - M206 and M428 are disabled.
  3440. * - G92 will revert to its behavior from Marlin 1.0.
  3441. */
  3442. //#define NO_WORKSPACE_OFFSETS
  3443. // Extra options for the M114 "Current Position" report
  3444. //#define M114_DETAIL // Use 'M114` for details to check planner calculations
  3445. //#define M114_REALTIME // Real current position based on forward kinematics
  3446. //#define M114_LEGACY // M114 used to synchronize on every call. Enable if needed.
  3447. //#define REPORT_FAN_CHANGE // Report the new fan speed when changed by M106 (and others)
  3448. /**
  3449. * Spend 28 bytes of SRAM to optimize the G-code parser
  3450. */
  3451. #define FASTER_GCODE_PARSER
  3452. #if ENABLED(FASTER_GCODE_PARSER)
  3453. //#define GCODE_QUOTED_STRINGS // Support for quoted string parameters
  3454. #endif
  3455. // Support for MeatPack G-code compression (https://github.com/scottmudge/OctoPrint-MeatPack)
  3456. //#define MEATPACK_ON_SERIAL_PORT_1
  3457. //#define MEATPACK_ON_SERIAL_PORT_2
  3458. //#define GCODE_CASE_INSENSITIVE // Accept G-code sent to the firmware in lowercase
  3459. //#define REPETIER_GCODE_M360 // Add commands originally from Repetier FW
  3460. /**
  3461. * CNC G-code options
  3462. * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
  3463. * Note that G0 feedrates should be used with care for 3D printing (if used at all).
  3464. * High feedrates may cause ringing and harm print quality.
  3465. */
  3466. //#define PAREN_COMMENTS // Support for parentheses-delimited comments
  3467. //#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
  3468. // Enable and set a (default) feedrate for all G0 moves
  3469. //#define G0_FEEDRATE 3000 // (mm/min)
  3470. #ifdef G0_FEEDRATE
  3471. //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
  3472. #endif
  3473. /**
  3474. * Startup commands
  3475. *
  3476. * Execute certain G-code commands immediately after power-on.
  3477. */
  3478. //#define STARTUP_COMMANDS "M17 Z"
  3479. /**
  3480. * G-code Macros
  3481. *
  3482. * Add G-codes M810-M819 to define and run G-code macros.
  3483. * Macros are not saved to EEPROM.
  3484. */
  3485. //#define GCODE_MACROS
  3486. #if ENABLED(GCODE_MACROS)
  3487. #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used
  3488. #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro
  3489. #endif
  3490. /**
  3491. * User-defined menu items to run custom G-code.
  3492. * Up to 25 may be defined, but the actual number is LCD-dependent.
  3493. */
  3494. // Custom Menu: Main Menu
  3495. //#define CUSTOM_MENU_MAIN
  3496. #if ENABLED(CUSTOM_MENU_MAIN)
  3497. //#define CUSTOM_MENU_MAIN_TITLE "Custom Commands"
  3498. #define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 User Script Done"
  3499. #define CUSTOM_MENU_MAIN_SCRIPT_AUDIBLE_FEEDBACK
  3500. //#define CUSTOM_MENU_MAIN_SCRIPT_RETURN // Return to status screen after a script
  3501. #define CUSTOM_MENU_MAIN_ONLY_IDLE // Only show custom menu when the machine is idle
  3502. #define MAIN_MENU_ITEM_1_DESC "Home & UBL Info"
  3503. #define MAIN_MENU_ITEM_1_GCODE "G28\nG29 W"
  3504. //#define MAIN_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action
  3505. #define MAIN_MENU_ITEM_2_DESC "Preheat for " PREHEAT_1_LABEL
  3506. #define MAIN_MENU_ITEM_2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  3507. //#define MAIN_MENU_ITEM_2_CONFIRM
  3508. //#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
  3509. //#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  3510. //#define MAIN_MENU_ITEM_3_CONFIRM
  3511. //#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
  3512. //#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  3513. //#define MAIN_MENU_ITEM_4_CONFIRM
  3514. //#define MAIN_MENU_ITEM_5_DESC "Home & Info"
  3515. //#define MAIN_MENU_ITEM_5_GCODE "G28\nM503"
  3516. //#define MAIN_MENU_ITEM_5_CONFIRM
  3517. #endif
  3518. // Custom Menu: Configuration Menu
  3519. //#define CUSTOM_MENU_CONFIG
  3520. #if ENABLED(CUSTOM_MENU_CONFIG)
  3521. //#define CUSTOM_MENU_CONFIG_TITLE "Custom Commands"
  3522. #define CUSTOM_MENU_CONFIG_SCRIPT_DONE "M117 Wireless Script Done"
  3523. #define CUSTOM_MENU_CONFIG_SCRIPT_AUDIBLE_FEEDBACK
  3524. //#define CUSTOM_MENU_CONFIG_SCRIPT_RETURN // Return to status screen after a script
  3525. #define CUSTOM_MENU_CONFIG_ONLY_IDLE // Only show custom menu when the machine is idle
  3526. #define CONFIG_MENU_ITEM_1_DESC "Wifi ON"
  3527. #define CONFIG_MENU_ITEM_1_GCODE "M118 [ESP110] WIFI-STA pwd=12345678"
  3528. //#define CONFIG_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action
  3529. #define CONFIG_MENU_ITEM_2_DESC "Bluetooth ON"
  3530. #define CONFIG_MENU_ITEM_2_GCODE "M118 [ESP110] BT pwd=12345678"
  3531. //#define CONFIG_MENU_ITEM_2_CONFIRM
  3532. //#define CONFIG_MENU_ITEM_3_DESC "Radio OFF"
  3533. //#define CONFIG_MENU_ITEM_3_GCODE "M118 [ESP110] OFF pwd=12345678"
  3534. //#define CONFIG_MENU_ITEM_3_CONFIRM
  3535. //#define CONFIG_MENU_ITEM_4_DESC "Wifi ????"
  3536. //#define CONFIG_MENU_ITEM_4_GCODE "M118 ????"
  3537. //#define CONFIG_MENU_ITEM_4_CONFIRM
  3538. //#define CONFIG_MENU_ITEM_5_DESC "Wifi ????"
  3539. //#define CONFIG_MENU_ITEM_5_GCODE "M118 ????"
  3540. //#define CONFIG_MENU_ITEM_5_CONFIRM
  3541. #endif
  3542. /**
  3543. * User-defined buttons to run custom G-code.
  3544. * Up to 25 may be defined.
  3545. */
  3546. //#define CUSTOM_USER_BUTTONS
  3547. #if ENABLED(CUSTOM_USER_BUTTONS)
  3548. //#define BUTTON1_PIN -1
  3549. #if PIN_EXISTS(BUTTON1)
  3550. #define BUTTON1_HIT_STATE LOW // State of the triggered button. NC=LOW. NO=HIGH.
  3551. #define BUTTON1_WHEN_PRINTING false // Button allowed to trigger during printing?
  3552. #define BUTTON1_GCODE "G28"
  3553. #define BUTTON1_DESC "Homing" // Optional string to set the LCD status
  3554. #endif
  3555. //#define BUTTON2_PIN -1
  3556. #if PIN_EXISTS(BUTTON2)
  3557. #define BUTTON2_HIT_STATE LOW
  3558. #define BUTTON2_WHEN_PRINTING false
  3559. #define BUTTON2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  3560. #define BUTTON2_DESC "Preheat for " PREHEAT_1_LABEL
  3561. #endif
  3562. //#define BUTTON3_PIN -1
  3563. #if PIN_EXISTS(BUTTON3)
  3564. #define BUTTON3_HIT_STATE LOW
  3565. #define BUTTON3_WHEN_PRINTING false
  3566. #define BUTTON3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  3567. #define BUTTON3_DESC "Preheat for " PREHEAT_2_LABEL
  3568. #endif
  3569. #endif
  3570. /**
  3571. * Host Action Commands
  3572. *
  3573. * Define host streamer action commands in compliance with the standard.
  3574. *
  3575. * See https://reprap.org/wiki/G-code#Action_commands
  3576. * Common commands ........ poweroff, pause, paused, resume, resumed, cancel
  3577. * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed
  3578. *
  3579. * Some features add reason codes to extend these commands.
  3580. *
  3581. * Host Prompt Support enables Marlin to use the host for user prompts so
  3582. * filament runout and other processes can be managed from the host side.
  3583. */
  3584. //#define HOST_ACTION_COMMANDS
  3585. #if ENABLED(HOST_ACTION_COMMANDS)
  3586. //#define HOST_PAUSE_M76 // Tell the host to pause in response to M76
  3587. //#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
  3588. #if ENABLED(HOST_PROMPT_SUPPORT)
  3589. //#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications
  3590. #endif
  3591. //#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
  3592. //#define HOST_SHUTDOWN_MENU_ITEM // Add a menu item that tells the host to shut down
  3593. #endif
  3594. /**
  3595. * Cancel Objects
  3596. *
  3597. * Implement M486 to allow Marlin to skip objects
  3598. */
  3599. //#define CANCEL_OBJECTS
  3600. #if ENABLED(CANCEL_OBJECTS)
  3601. #define CANCEL_OBJECTS_REPORTING // Emit the current object as a status message
  3602. #endif
  3603. /**
  3604. * I2C position encoders for closed loop control.
  3605. * Developed by Chris Barr at Aus3D.
  3606. *
  3607. * Wiki: https://wiki.aus3d.com.au/Magnetic_Encoder
  3608. * Github: https://github.com/Aus3D/MagneticEncoder
  3609. *
  3610. * Supplier: https://aus3d.com.au/magnetic-encoder-module
  3611. * Alternative Supplier: https://reliabuild3d.com/
  3612. *
  3613. * Reliabuild encoders have been modified to improve reliability.
  3614. */
  3615. //#define I2C_POSITION_ENCODERS
  3616. #if ENABLED(I2C_POSITION_ENCODERS)
  3617. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  3618. // encoders supported currently.
  3619. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  3620. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  3621. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  3622. // I2CPE_ENC_TYPE_ROTARY.
  3623. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  3624. // 1mm poles. For linear encoders this is ticks / mm,
  3625. // for rotary encoders this is ticks / revolution.
  3626. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  3627. // steps per full revolution (motor steps/rev * microstepping)
  3628. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  3629. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction.
  3630. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  3631. // printer will attempt to correct the error; errors
  3632. // smaller than this are ignored to minimize effects of
  3633. // measurement noise / latency (filter).
  3634. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  3635. #define I2CPE_ENC_2_AXIS Y_AXIS
  3636. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  3637. #define I2CPE_ENC_2_TICKS_UNIT 2048
  3638. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  3639. //#define I2CPE_ENC_2_INVERT
  3640. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP
  3641. #define I2CPE_ENC_2_EC_THRESH 0.10
  3642. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  3643. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  3644. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  3645. #define I2CPE_ENC_4_AXIS E_AXIS
  3646. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  3647. #define I2CPE_ENC_5_AXIS E_AXIS
  3648. // Default settings for encoders which are enabled, but without settings configured above.
  3649. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  3650. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  3651. #define I2CPE_DEF_TICKS_REV (16 * 200)
  3652. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  3653. #define I2CPE_DEF_EC_THRESH 0.1
  3654. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  3655. // axis after which the printer will abort. Comment out to
  3656. // disable abort behavior.
  3657. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  3658. // for this amount of time (in ms) before the encoder
  3659. // is trusted again.
  3660. /**
  3661. * Position is checked every time a new command is executed from the buffer but during long moves,
  3662. * this setting determines the minimum update time between checks. A value of 100 works well with
  3663. * error rolling average when attempting to correct only for skips and not for vibration.
  3664. */
  3665. #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks.
  3666. // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
  3667. #define I2CPE_ERR_ROLLING_AVERAGE
  3668. #endif // I2C_POSITION_ENCODERS
  3669. /**
  3670. * Analog Joystick(s)
  3671. */
  3672. //#define JOYSTICK
  3673. #if ENABLED(JOYSTICK)
  3674. #define JOY_X_PIN 5 // RAMPS: Suggested pin A5 on AUX2
  3675. #define JOY_Y_PIN 10 // RAMPS: Suggested pin A10 on AUX2
  3676. #define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
  3677. #define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
  3678. //#define INVERT_JOY_X // Enable if X direction is reversed
  3679. //#define INVERT_JOY_Y // Enable if Y direction is reversed
  3680. //#define INVERT_JOY_Z // Enable if Z direction is reversed
  3681. // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
  3682. #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
  3683. #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
  3684. #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
  3685. //#define JOYSTICK_DEBUG
  3686. #endif
  3687. /**
  3688. * Mechanical Gantry Calibration
  3689. * Modern replacement for the Prusa TMC_Z_CALIBRATION.
  3690. * Adds capability to work with any adjustable current drivers.
  3691. * Implemented as G34 because M915 is deprecated.
  3692. */
  3693. //#define MECHANICAL_GANTRY_CALIBRATION
  3694. #if ENABLED(MECHANICAL_GANTRY_CALIBRATION)
  3695. #define GANTRY_CALIBRATION_CURRENT 600 // Default calibration current in ma
  3696. #define GANTRY_CALIBRATION_EXTRA_HEIGHT 15 // Extra distance in mm past Z_###_POS to move
  3697. #define GANTRY_CALIBRATION_FEEDRATE 500 // Feedrate for correction move
  3698. //#define GANTRY_CALIBRATION_TO_MIN // Enable to calibrate Z in the MIN direction
  3699. //#define GANTRY_CALIBRATION_SAFE_POSITION XY_CENTER // Safe position for nozzle
  3700. //#define GANTRY_CALIBRATION_XY_PARK_FEEDRATE 3000 // XY Park Feedrate - MMM
  3701. //#define GANTRY_CALIBRATION_COMMANDS_PRE ""
  3702. #define GANTRY_CALIBRATION_COMMANDS_POST "G28" // G28 highly recommended to ensure an accurate position
  3703. #endif
  3704. /**
  3705. * Instant freeze / unfreeze functionality
  3706. * Potentially useful for emergency stop that allows being resumed.
  3707. */
  3708. //#define FREEZE_FEATURE
  3709. #if ENABLED(FREEZE_FEATURE)
  3710. //#define FREEZE_PIN 41 // Override the default (KILL) pin here
  3711. #define FREEZE_STATE LOW // State of pin indicating freeze
  3712. #endif
  3713. /**
  3714. * MAX7219 Debug Matrix
  3715. *
  3716. * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
  3717. * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
  3718. */
  3719. //#define MAX7219_DEBUG
  3720. #if ENABLED(MAX7219_DEBUG)
  3721. #define MAX7219_CLK_PIN 64
  3722. #define MAX7219_DIN_PIN 57
  3723. #define MAX7219_LOAD_PIN 44
  3724. //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix
  3725. #define MAX7219_INIT_TEST 2 // Test pattern at startup: 0=none, 1=sweep, 2=spiral
  3726. #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain.
  3727. #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°)
  3728. // connector at: right=0 bottom=-90 top=90 left=180
  3729. //#define MAX7219_REVERSE_ORDER // The order of the LED matrix units may be reversed
  3730. //#define MAX7219_REVERSE_EACH // The LEDs in each matrix unit row may be reversed
  3731. //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side
  3732. /**
  3733. * Sample debug features
  3734. * If you add more debug displays, be careful to avoid conflicts!
  3735. */
  3736. #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
  3737. #define MAX7219_DEBUG_PLANNER_HEAD 2 // Show the planner queue head position on this and the next LED matrix row
  3738. #define MAX7219_DEBUG_PLANNER_TAIL 4 // Show the planner queue tail position on this and the next LED matrix row
  3739. #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row
  3740. // If you experience stuttering, reboots, etc. this option can reveal how
  3741. // tweaks made to the configuration are affecting the printer in real-time.
  3742. #define MAX7219_DEBUG_PROFILE 6 // Display the fraction of CPU time spent in profiled code on this LED matrix
  3743. // row. By default idle() is profiled so this shows how "idle" the processor is.
  3744. // See class CodeProfiler.
  3745. #endif
  3746. /**
  3747. * NanoDLP Sync support
  3748. *
  3749. * Support for Synchronized Z moves when used with NanoDLP. G0/G1 axis moves will
  3750. * output a "Z_move_comp" string to enable synchronization with DLP projector exposure.
  3751. * This feature allows you to use [[WaitForDoneMessage]] instead of M400 commands.
  3752. */
  3753. //#define NANODLP_Z_SYNC
  3754. #if ENABLED(NANODLP_Z_SYNC)
  3755. //#define NANODLP_ALL_AXIS // Send a "Z_move_comp" report for any axis move (not just Z).
  3756. #endif
  3757. /**
  3758. * Ethernet. Use M552 to enable and set the IP address.
  3759. */
  3760. #if HAS_ETHERNET
  3761. #define MAC_ADDRESS { 0xDE, 0xAD, 0xBE, 0xEF, 0xF0, 0x0D } // A MAC address unique to your network
  3762. #endif
  3763. /**
  3764. * WiFi Support (Espressif ESP32 WiFi)
  3765. */
  3766. //#define WIFISUPPORT // Marlin embedded WiFi managenent
  3767. //#define ESP3D_WIFISUPPORT // ESP3D Library WiFi management (https://github.com/luc-github/ESP3DLib)
  3768. #if EITHER(WIFISUPPORT, ESP3D_WIFISUPPORT)
  3769. //#define WEBSUPPORT // Start a webserver (which may include auto-discovery)
  3770. //#define OTASUPPORT // Support over-the-air firmware updates
  3771. //#define WIFI_CUSTOM_COMMAND // Accept feature config commands (e.g., WiFi ESP3D) from the host
  3772. /**
  3773. * To set a default WiFi SSID / Password, create a file called Configuration_Secure.h with
  3774. * the following defines, customized for your network. This specific file is excluded via
  3775. * .gitignore to prevent it from accidentally leaking to the public.
  3776. *
  3777. * #define WIFI_SSID "WiFi SSID"
  3778. * #define WIFI_PWD "WiFi Password"
  3779. */
  3780. //#include "Configuration_Secure.h" // External file with WiFi SSID / Password
  3781. #endif
  3782. /**
  3783. * Průša Multi-Material Unit (MMU)
  3784. * Enable in Configuration.h
  3785. *
  3786. * These devices allow a single stepper driver on the board to drive
  3787. * multi-material feeders with any number of stepper motors.
  3788. */
  3789. #if HAS_PRUSA_MMU1
  3790. /**
  3791. * This option only allows the multiplexer to switch on tool-change.
  3792. * Additional options to configure custom E moves are pending.
  3793. *
  3794. * Override the default DIO selector pins here, if needed.
  3795. * Some pins files may provide defaults for these pins.
  3796. */
  3797. //#define E_MUX0_PIN 40 // Always Required
  3798. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  3799. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  3800. #elif HAS_PRUSA_MMU2
  3801. // Serial port used for communication with MMU2.
  3802. #define MMU2_SERIAL_PORT 2
  3803. // Use hardware reset for MMU if a pin is defined for it
  3804. //#define MMU2_RST_PIN 23
  3805. // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up)
  3806. //#define MMU2_MODE_12V
  3807. // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout
  3808. #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600"
  3809. // Add an LCD menu for MMU2
  3810. //#define MMU2_MENUS
  3811. #if EITHER(MMU2_MENUS, HAS_PRUSA_MMU2S)
  3812. // Settings for filament load / unload from the LCD menu.
  3813. // This is for Průša MK3-style extruders. Customize for your hardware.
  3814. #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0
  3815. #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \
  3816. { 7.2, 1145 }, \
  3817. { 14.4, 871 }, \
  3818. { 36.0, 1393 }, \
  3819. { 14.4, 871 }, \
  3820. { 50.0, 198 }
  3821. #define MMU2_RAMMING_SEQUENCE \
  3822. { 1.0, 1000 }, \
  3823. { 1.0, 1500 }, \
  3824. { 2.0, 2000 }, \
  3825. { 1.5, 3000 }, \
  3826. { 2.5, 4000 }, \
  3827. { -15.0, 5000 }, \
  3828. { -14.0, 1200 }, \
  3829. { -6.0, 600 }, \
  3830. { 10.0, 700 }, \
  3831. { -10.0, 400 }, \
  3832. { -50.0, 2000 }
  3833. #endif
  3834. /**
  3835. * Using a sensor like the MMU2S
  3836. * This mode requires a MK3S extruder with a sensor at the extruder idler, like the MMU2S.
  3837. * See https://help.prusa3d.com/en/guide/3b-mk3s-mk2-5s-extruder-upgrade_41560, step 11
  3838. */
  3839. #if HAS_PRUSA_MMU2S
  3840. #define MMU2_C0_RETRY 5 // Number of retries (total time = timeout*retries)
  3841. #define MMU2_CAN_LOAD_FEEDRATE 800 // (mm/min)
  3842. #define MMU2_CAN_LOAD_SEQUENCE \
  3843. { 0.1, MMU2_CAN_LOAD_FEEDRATE }, \
  3844. { 60.0, MMU2_CAN_LOAD_FEEDRATE }, \
  3845. { -52.0, MMU2_CAN_LOAD_FEEDRATE }
  3846. #define MMU2_CAN_LOAD_RETRACT 6.0 // (mm) Keep under the distance between Load Sequence values
  3847. #define MMU2_CAN_LOAD_DEVIATION 0.8 // (mm) Acceptable deviation
  3848. #define MMU2_CAN_LOAD_INCREMENT 0.2 // (mm) To reuse within MMU2 module
  3849. #define MMU2_CAN_LOAD_INCREMENT_SEQUENCE \
  3850. { -MMU2_CAN_LOAD_INCREMENT, MMU2_CAN_LOAD_FEEDRATE }
  3851. #else
  3852. /**
  3853. * MMU1 Extruder Sensor
  3854. *
  3855. * Support for a Průša (or other) IR Sensor to detect filament near the extruder
  3856. * and make loading more reliable. Suitable for an extruder equipped with a filament
  3857. * sensor less than 38mm from the gears.
  3858. *
  3859. * During loading the extruder will stop when the sensor is triggered, then do a last
  3860. * move up to the gears. If no filament is detected, the MMU2 can make some more attempts.
  3861. * If all attempts fail, a filament runout will be triggered.
  3862. */
  3863. //#define MMU_EXTRUDER_SENSOR
  3864. #if ENABLED(MMU_EXTRUDER_SENSOR)
  3865. #define MMU_LOADING_ATTEMPTS_NR 5 // max. number of attempts to load filament if first load fail
  3866. #endif
  3867. #endif
  3868. //#define MMU2_DEBUG // Write debug info to serial output
  3869. #endif // HAS_PRUSA_MMU2
  3870. /**
  3871. * Advanced Print Counter settings
  3872. */
  3873. #if ENABLED(PRINTCOUNTER)
  3874. #define SERVICE_WARNING_BUZZES 3
  3875. // Activate up to 3 service interval watchdogs
  3876. //#define SERVICE_NAME_1 "Service S"
  3877. //#define SERVICE_INTERVAL_1 100 // print hours
  3878. //#define SERVICE_NAME_2 "Service L"
  3879. //#define SERVICE_INTERVAL_2 200 // print hours
  3880. //#define SERVICE_NAME_3 "Service 3"
  3881. //#define SERVICE_INTERVAL_3 1 // print hours
  3882. #endif
  3883. // @section develop
  3884. //
  3885. // M100 Free Memory Watcher to debug memory usage
  3886. //
  3887. //#define M100_FREE_MEMORY_WATCHER
  3888. //
  3889. // M42 - Set pin states
  3890. //
  3891. //#define DIRECT_PIN_CONTROL
  3892. //
  3893. // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
  3894. //
  3895. //#define PINS_DEBUGGING
  3896. // Enable Marlin dev mode which adds some special commands
  3897. //#define MARLIN_DEV_MODE
  3898. #if ENABLED(MARLIN_DEV_MODE)
  3899. /**
  3900. * D576 - Buffer Monitoring
  3901. * To help diagnose print quality issues stemming from empty command buffers.
  3902. */
  3903. //#define BUFFER_MONITORING
  3904. #endif
  3905. /**
  3906. * Postmortem Debugging captures misbehavior and outputs the CPU status and backtrace to serial.
  3907. * When running in the debugger it will break for debugging. This is useful to help understand
  3908. * a crash from a remote location. Requires ~400 bytes of SRAM and 5Kb of flash.
  3909. */
  3910. //#define POSTMORTEM_DEBUGGING
  3911. /**
  3912. * Software Reset options
  3913. */
  3914. //#define SOFT_RESET_VIA_SERIAL // 'KILL' and '^X' commands will soft-reset the controller
  3915. //#define SOFT_RESET_ON_KILL // Use a digital button to soft-reset the controller after KILL
  3916. // Report uncleaned reset reason from register r2 instead of MCUSR. Supported by Optiboot on AVR.
  3917. //#define OPTIBOOT_RESET_REASON