My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration.h 80KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720172117221723172417251726172717281729173017311732173317341735173617371738173917401741174217431744174517461747174817491750175117521753175417551756175717581759176017611762176317641765176617671768176917701771177217731774177517761777177817791780178117821783178417851786178717881789179017911792179317941795179617971798179918001801180218031804180518061807180818091810181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391840184118421843184418451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906190719081909191019111912191319141915191619171918191919201921192219231924192519261927192819291930193119321933193419351936193719381939194019411942194319441945194619471948194919501951195219531954195519561957195819591960196119621963196419651966196719681969197019711972197319741975197619771978197919801981198219831984198519861987198819891990199119921993199419951996199719981999200020012002200320042005200620072008200920102011201220132014201520162017201820192020202120222023202420252026202720282029203020312032203320342035203620372038203920402041204220432044204520462047204820492050205120522053205420552056205720582059206020612062206320642065206620672068206920702071207220732074207520762077207820792080208120822083208420852086208720882089209020912092209320942095209620972098209921002101210221032104210521062107210821092110211121122113211421152116211721182119212021212122212321242125212621272128212921302131213221332134213521362137213821392140214121422143214421452146214721482149215021512152215321542155215621572158215921602161216221632164216521662167216821692170217121722173217421752176217721782179218021812182218321842185218621872188218921902191219221932194
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23. /**
  24. * Configuration.h
  25. *
  26. * Basic settings such as:
  27. *
  28. * - Type of electronics
  29. * - Type of temperature sensor
  30. * - Printer geometry
  31. * - Endstop configuration
  32. * - LCD controller
  33. * - Extra features
  34. *
  35. * Advanced settings can be found in Configuration_adv.h
  36. *
  37. */
  38. #define CONFIGURATION_H_VERSION 020000
  39. //===========================================================================
  40. //============================= Getting Started =============================
  41. //===========================================================================
  42. /**
  43. * Here are some standard links for getting your machine calibrated:
  44. *
  45. * http://reprap.org/wiki/Calibration
  46. * http://youtu.be/wAL9d7FgInk
  47. * http://calculator.josefprusa.cz
  48. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  49. * http://www.thingiverse.com/thing:5573
  50. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  51. * http://www.thingiverse.com/thing:298812
  52. */
  53. //===========================================================================
  54. //============================= DELTA Printer ===============================
  55. //===========================================================================
  56. // For a Delta printer start with one of the configuration files in the
  57. // config/examples/delta directory and customize for your machine.
  58. //
  59. //===========================================================================
  60. //============================= SCARA Printer ===============================
  61. //===========================================================================
  62. // For a SCARA printer start with the configuration files in
  63. // config/examples/SCARA and customize for your machine.
  64. //
  65. // @section info
  66. // Author info of this build printed to the host during boot and M115
  67. #define STRING_CONFIG_H_AUTHOR "(Scheepers, MaukCC)" // Who made the changes.
  68. /**
  69. * *** VENDORS PLEASE READ ***
  70. *
  71. * Marlin allows you to add a custom boot image for Graphical LCDs.
  72. * With this option Marlin will first show your custom screen followed
  73. * by the standard Marlin logo with version number and web URL.
  74. *
  75. * We encourage you to take advantage of this new feature and we also
  76. * respectfully request that you retain the unmodified Marlin boot screen.
  77. */
  78. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  79. #define SHOW_BOOTSCREEN
  80. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  81. //#define SHOW_CUSTOM_BOOTSCREEN
  82. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  83. //#define CUSTOM_STATUS_SCREEN_IMAGE
  84. // @section machine
  85. /**
  86. * Select the serial port on the board to use for communication with the host.
  87. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  88. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  89. *
  90. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  91. */
  92. #define SERIAL_PORT 0
  93. /**
  94. * Select a secondary serial port on the board to use for communication with the host.
  95. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  96. * Serial port -1 is the USB emulated serial port, if available.
  97. *
  98. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  99. */
  100. //#define SERIAL_PORT_2 -1
  101. /**
  102. * This setting determines the communication speed of the printer.
  103. *
  104. * 250000 works in most cases, but you might try a lower speed if
  105. * you commonly experience drop-outs during host printing.
  106. * You may try up to 1000000 to speed up SD file transfer.
  107. *
  108. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  109. */
  110. #define BAUDRATE 250000
  111. // Enable the Bluetooth serial interface on AT90USB devices
  112. //#define BLUETOOTH
  113. // Choose the name from boards.h that matches your setup
  114. #ifndef MOTHERBOARD
  115. #define MOTHERBOARD BOARD_CNCONTROLS_15
  116. #endif
  117. // Name displayed in the LCD "Ready" message and Info menu
  118. //#define CUSTOM_MACHINE_NAME "3D Printer"
  119. // Printer's unique ID, used by some programs to differentiate between machines.
  120. // Choose your own or use a service like http://www.uuidgenerator.net/version4
  121. #define MACHINE_UUID "75083866-86ea-42b2-b475-7b3a7855e716"
  122. // @section extruder
  123. // This defines the number of extruders
  124. // :[1, 2, 3, 4, 5, 6]
  125. #define EXTRUDERS 1
  126. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  127. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  128. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  129. //#define SINGLENOZZLE
  130. /**
  131. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  132. *
  133. * This device allows one stepper driver on a control board to drive
  134. * two to eight stepper motors, one at a time, in a manner suitable
  135. * for extruders.
  136. *
  137. * This option only allows the multiplexer to switch on tool-change.
  138. * Additional options to configure custom E moves are pending.
  139. */
  140. //#define MK2_MULTIPLEXER
  141. #if ENABLED(MK2_MULTIPLEXER)
  142. // Override the default DIO selector pins here, if needed.
  143. // Some pins files may provide defaults for these pins.
  144. //#define E_MUX0_PIN 40 // Always Required
  145. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  146. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  147. #endif
  148. /**
  149. * Prusa Multi-Material Unit v2
  150. *
  151. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  152. * Requires EXTRUDERS = 5
  153. *
  154. * For additional configuration see Configuration_adv.h
  155. */
  156. //#define PRUSA_MMU2
  157. // A dual extruder that uses a single stepper motor
  158. //#define SWITCHING_EXTRUDER
  159. #if ENABLED(SWITCHING_EXTRUDER)
  160. #define SWITCHING_EXTRUDER_SERVO_NR 0
  161. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  162. #if EXTRUDERS > 3
  163. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  164. #endif
  165. #endif
  166. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  167. //#define SWITCHING_NOZZLE
  168. #if ENABLED(SWITCHING_NOZZLE)
  169. #define SWITCHING_NOZZLE_SERVO_NR 0
  170. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  171. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  172. #endif
  173. /**
  174. * Two separate X-carriages with extruders that connect to a moving part
  175. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  176. */
  177. //#define PARKING_EXTRUDER
  178. /**
  179. * Two separate X-carriages with extruders that connect to a moving part
  180. * via a magnetic docking mechanism using movements and no solenoid
  181. *
  182. * project : https://www.thingiverse.com/thing:3080893
  183. * movements : https://youtu.be/0xCEiG9VS3k
  184. * https://youtu.be/Bqbcs0CU2FE
  185. */
  186. //#define MAGNETIC_PARKING_EXTRUDER
  187. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  188. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  189. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  190. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  191. #if ENABLED(PARKING_EXTRUDER)
  192. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  193. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  194. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  195. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  196. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  197. #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
  198. #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
  199. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  200. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  201. #endif
  202. #endif
  203. /**
  204. * Switching Toolhead
  205. *
  206. * Support for swappable and dockable toolheads, such as
  207. * the E3D Tool Changer. Toolheads are locked with a servo.
  208. */
  209. //#define SWITCHING_TOOLHEAD
  210. /**
  211. * Magnetic Switching Toolhead
  212. *
  213. * Support swappable and dockable toolheads with a magnetic
  214. * docking mechanism using movement and no servo.
  215. */
  216. //#define MAGNETIC_SWITCHING_TOOLHEAD
  217. /**
  218. * Electromagnetic Switching Toolhead
  219. *
  220. * Parking for CoreXY / HBot kinematics.
  221. * Toolheads are parked at one edge and held with an electromagnet.
  222. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  223. */
  224. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  225. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  226. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  227. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  228. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  229. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  230. #if ENABLED(SWITCHING_TOOLHEAD)
  231. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  232. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  233. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  234. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  235. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  236. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  237. #if ENABLED(PRIME_BEFORE_REMOVE)
  238. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  239. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  240. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate
  241. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate
  242. #endif
  243. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  244. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  245. #endif
  246. #endif
  247. /**
  248. * "Mixing Extruder"
  249. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  250. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  251. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  252. * - This implementation supports up to two mixing extruders.
  253. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  254. */
  255. //#define MIXING_EXTRUDER
  256. #if ENABLED(MIXING_EXTRUDER)
  257. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  258. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  259. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  260. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  261. #if ENABLED(GRADIENT_MIX)
  262. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  263. #endif
  264. #endif
  265. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  266. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  267. // For the other hotends it is their distance from the extruder 0 hotend.
  268. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  269. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  270. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  271. // @section machine
  272. /**
  273. * Power Supply Control
  274. *
  275. * Enable and connect the power supply to the PS_ON_PIN.
  276. * Specify whether the power supply is active HIGH or active LOW.
  277. */
  278. //#define PSU_CONTROL
  279. //#define PSU_NAME "Power Supply"
  280. #if ENABLED(PSU_CONTROL)
  281. #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
  282. //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80
  283. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  284. #if ENABLED(AUTO_POWER_CONTROL)
  285. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  286. #define AUTO_POWER_E_FANS
  287. #define AUTO_POWER_CONTROLLERFAN
  288. #define AUTO_POWER_CHAMBER_FAN
  289. //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature
  290. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature
  291. #define POWER_TIMEOUT 30
  292. #endif
  293. #endif
  294. // @section temperature
  295. //===========================================================================
  296. //============================= Thermal Settings ============================
  297. //===========================================================================
  298. /**
  299. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  300. *
  301. * Temperature sensors available:
  302. *
  303. * -4 : thermocouple with AD8495
  304. * -3 : thermocouple with MAX31855 (only for sensor 0)
  305. * -2 : thermocouple with MAX6675 (only for sensor 0)
  306. * -1 : thermocouple with AD595
  307. * 0 : not used
  308. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  309. * 331 : (3.3V scaled thermistor 1 table)
  310. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  311. * 3 : Mendel-parts thermistor (4.7k pullup)
  312. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  313. * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  314. * 501 : 100K Zonestar (Tronxy X3A) Thermistor
  315. * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  316. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  317. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  318. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  319. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  320. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  321. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  322. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  323. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  324. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  325. * 15 : 100k thermistor calibration for JGAurora A5 hotend
  326. * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
  327. * 20 : Pt100 with circuit in the Ultimainboard V2.x
  328. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  329. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  330. * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
  331. * 66 : 4.7M High Temperature thermistor from Dyze Design
  332. * 67 : 450C thermistor from SliceEngineering
  333. * 70 : the 100K thermistor found in the bq Hephestos 2
  334. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  335. *
  336. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  337. * (but gives greater accuracy and more stable PID)
  338. * 51 : 100k thermistor - EPCOS (1k pullup)
  339. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  340. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  341. *
  342. * 1047 : Pt1000 with 4k7 pullup
  343. * 1010 : Pt1000 with 1k pullup (non standard)
  344. * 147 : Pt100 with 4k7 pullup
  345. * 110 : Pt100 with 1k pullup (non standard)
  346. *
  347. * 1000 : Custom - Specify parameters in Configuration_adv.h
  348. *
  349. * Use these for Testing or Development purposes. NEVER for production machine.
  350. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  351. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  352. *
  353. * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
  354. */
  355. #define TEMP_SENSOR_0 -1
  356. #define TEMP_SENSOR_1 0
  357. #define TEMP_SENSOR_2 0
  358. #define TEMP_SENSOR_3 0
  359. #define TEMP_SENSOR_4 0
  360. #define TEMP_SENSOR_5 0
  361. #define TEMP_SENSOR_BED 331
  362. #define TEMP_SENSOR_CHAMBER 331
  363. // Dummy thermistor constant temperature readings, for use with 998 and 999
  364. #define DUMMY_THERMISTOR_998_VALUE 25
  365. #define DUMMY_THERMISTOR_999_VALUE 100
  366. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  367. // from the two sensors differ too much the print will be aborted.
  368. //#define TEMP_SENSOR_1_AS_REDUNDANT
  369. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  370. #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
  371. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  372. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  373. #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
  374. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  375. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  376. // Below this temperature the heater will be switched off
  377. // because it probably indicates a broken thermistor wire.
  378. #define HEATER_0_MINTEMP 5
  379. #define HEATER_1_MINTEMP 5
  380. #define HEATER_2_MINTEMP 5
  381. #define HEATER_3_MINTEMP 5
  382. #define HEATER_4_MINTEMP 5
  383. #define HEATER_5_MINTEMP 5
  384. #define BED_MINTEMP 5
  385. // Above this temperature the heater will be switched off.
  386. // This can protect components from overheating, but NOT from shorts and failures.
  387. // (Use MINTEMP for thermistor short/failure protection.)
  388. #define HEATER_0_MAXTEMP 410
  389. #define HEATER_1_MAXTEMP 410
  390. #define HEATER_2_MAXTEMP 410
  391. #define HEATER_3_MAXTEMP 410
  392. #define BED_MAXTEMP 150
  393. //===========================================================================
  394. //============================= PID Settings ================================
  395. //===========================================================================
  396. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  397. // Comment the following line to disable PID and enable bang-bang.
  398. #define PIDTEMP
  399. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  400. #define PID_MAX 170 // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  401. #define PID_K1 0.95 // Smoothing factor within any PID loop
  402. #if ENABLED(PIDTEMP)
  403. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
  404. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
  405. //#define PID_DEBUG // Sends debug data to the serial port.
  406. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  407. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  408. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  409. // Set/get with gcode: M301 E[extruder number, 0-2]
  410. #define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
  411. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  412. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  413. #define DEFAULT_Kp 11.3
  414. #define DEFAULT_Ki 0.61
  415. #define DEFAULT_Kd 52.77
  416. #endif // PIDTEMP
  417. //===========================================================================
  418. //====================== PID > Bed Temperature Control ======================
  419. //===========================================================================
  420. /**
  421. * PID Bed Heating
  422. *
  423. * If this option is enabled set PID constants below.
  424. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  425. *
  426. * The PID frequency will be the same as the extruder PWM.
  427. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  428. * which is fine for driving a square wave into a resistive load and does not significantly
  429. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  430. * heater. If your configuration is significantly different than this and you don't understand
  431. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  432. */
  433. //#define PIDTEMPBED
  434. //#define BED_LIMIT_SWITCHING
  435. /**
  436. * Max Bed Power
  437. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  438. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  439. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  440. */
  441. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  442. #if ENABLED(PIDTEMPBED)
  443. //#define MIN_BED_POWER 0
  444. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  445. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  446. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  447. #define DEFAULT_bedKp 10.00
  448. #define DEFAULT_bedKi .023
  449. #define DEFAULT_bedKd 305.4
  450. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  451. //from pidautotune
  452. //#define DEFAULT_bedKp 97.1
  453. //#define DEFAULT_bedKi 1.41
  454. //#define DEFAULT_bedKd 1675.16
  455. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  456. #endif // PIDTEMPBED
  457. // @section extruder
  458. /**
  459. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  460. * Add M302 to set the minimum extrusion temperature and/or turn
  461. * cold extrusion prevention on and off.
  462. *
  463. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  464. */
  465. #define PREVENT_COLD_EXTRUSION
  466. #define EXTRUDE_MINTEMP 18
  467. /**
  468. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  469. * Note: For Bowden Extruders make this large enough to allow load/unload.
  470. */
  471. #define PREVENT_LENGTHY_EXTRUDE
  472. #define EXTRUDE_MAXLENGTH 200
  473. //===========================================================================
  474. //======================== Thermal Runaway Protection =======================
  475. //===========================================================================
  476. /**
  477. * Thermal Protection provides additional protection to your printer from damage
  478. * and fire. Marlin always includes safe min and max temperature ranges which
  479. * protect against a broken or disconnected thermistor wire.
  480. *
  481. * The issue: If a thermistor falls out, it will report the much lower
  482. * temperature of the air in the room, and the the firmware will keep
  483. * the heater on.
  484. *
  485. * If you get "Thermal Runaway" or "Heating failed" errors the
  486. * details can be tuned in Configuration_adv.h
  487. */
  488. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  489. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  490. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  491. //===========================================================================
  492. //============================= Mechanical Settings =========================
  493. //===========================================================================
  494. // @section machine
  495. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  496. // either in the usual order or reversed
  497. //#define COREXY
  498. //#define COREXZ
  499. //#define COREYZ
  500. //#define COREYX
  501. //#define COREZX
  502. //#define COREZY
  503. //===========================================================================
  504. //============================== Endstop Settings ===========================
  505. //===========================================================================
  506. // @section homing
  507. // Specify here all the endstop connectors that are connected to any endstop or probe.
  508. // Almost all printers will be using one per axis. Probes will use one or more of the
  509. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  510. #define USE_XMIN_PLUG
  511. #define USE_YMIN_PLUG
  512. #define USE_ZMIN_PLUG
  513. //#define USE_XMAX_PLUG
  514. //#define USE_YMAX_PLUG
  515. //#define USE_ZMAX_PLUG
  516. // Enable pullup for all endstops to prevent a floating state
  517. #define ENDSTOPPULLUPS
  518. #if DISABLED(ENDSTOPPULLUPS)
  519. // Disable ENDSTOPPULLUPS to set pullups individually
  520. //#define ENDSTOPPULLUP_XMAX
  521. //#define ENDSTOPPULLUP_YMAX
  522. //#define ENDSTOPPULLUP_ZMAX
  523. //#define ENDSTOPPULLUP_XMIN
  524. //#define ENDSTOPPULLUP_YMIN
  525. //#define ENDSTOPPULLUP_ZMIN
  526. //#define ENDSTOPPULLUP_ZMIN_PROBE
  527. #endif
  528. // Enable pulldown for all endstops to prevent a floating state
  529. //#define ENDSTOPPULLDOWNS
  530. #if DISABLED(ENDSTOPPULLDOWNS)
  531. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  532. //#define ENDSTOPPULLDOWN_XMAX
  533. //#define ENDSTOPPULLDOWN_YMAX
  534. //#define ENDSTOPPULLDOWN_ZMAX
  535. //#define ENDSTOPPULLDOWN_XMIN
  536. //#define ENDSTOPPULLDOWN_YMIN
  537. //#define ENDSTOPPULLDOWN_ZMIN
  538. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  539. #endif
  540. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  541. #define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  542. #define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  543. #define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  544. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  545. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  546. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  547. #define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
  548. /**
  549. * Stepper Drivers
  550. *
  551. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  552. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  553. *
  554. * A4988 is assumed for unspecified drivers.
  555. *
  556. * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
  557. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  558. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  559. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  560. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  561. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  562. */
  563. //#define X_DRIVER_TYPE A4988
  564. //#define Y_DRIVER_TYPE A4988
  565. //#define Z_DRIVER_TYPE A4988
  566. //#define X2_DRIVER_TYPE A4988
  567. //#define Y2_DRIVER_TYPE A4988
  568. //#define Z2_DRIVER_TYPE A4988
  569. //#define Z3_DRIVER_TYPE A4988
  570. //#define E0_DRIVER_TYPE A4988
  571. //#define E1_DRIVER_TYPE A4988
  572. //#define E2_DRIVER_TYPE A4988
  573. //#define E3_DRIVER_TYPE A4988
  574. //#define E4_DRIVER_TYPE A4988
  575. //#define E5_DRIVER_TYPE A4988
  576. // Enable this feature if all enabled endstop pins are interrupt-capable.
  577. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  578. //#define ENDSTOP_INTERRUPTS_FEATURE
  579. /**
  580. * Endstop Noise Threshold
  581. *
  582. * Enable if your probe or endstops falsely trigger due to noise.
  583. *
  584. * - Higher values may affect repeatability or accuracy of some bed probes.
  585. * - To fix noise install a 100nF ceramic capacitor inline with the switch.
  586. * - This feature is not required for common micro-switches mounted on PCBs
  587. * based on the Makerbot design, which already have the 100nF capacitor.
  588. *
  589. * :[2,3,4,5,6,7]
  590. */
  591. //#define ENDSTOP_NOISE_THRESHOLD 2
  592. //=============================================================================
  593. //============================== Movement Settings ============================
  594. //=============================================================================
  595. // @section motion
  596. /**
  597. * Default Settings
  598. *
  599. * These settings can be reset by M502
  600. *
  601. * Note that if EEPROM is enabled, saved values will override these.
  602. */
  603. /**
  604. * With this option each E stepper can have its own factors for the
  605. * following movement settings. If fewer factors are given than the
  606. * total number of extruders, the last value applies to the rest.
  607. */
  608. //#define DISTINCT_E_FACTORS
  609. /**
  610. * Default Axis Steps Per Unit (steps/mm)
  611. * Override with M92
  612. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  613. */
  614. #define DEFAULT_AXIS_STEPS_PER_UNIT { 53.45, 71.19, 160, 169.05 }
  615. /**
  616. * Default Max Feed Rate (mm/s)
  617. * Override with M203
  618. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  619. */
  620. #define DEFAULT_MAX_FEEDRATE { 1000, 1000, 40, 25 }
  621. /**
  622. * Default Max Acceleration (change/s) change = mm/s
  623. * (Maximum start speed for accelerated moves)
  624. * Override with M201
  625. * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  626. */
  627. #define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 10000 }
  628. /**
  629. * Default Acceleration (change/s) change = mm/s
  630. * Override with M204
  631. *
  632. * M204 P Acceleration
  633. * M204 R Retract Acceleration
  634. * M204 T Travel Acceleration
  635. */
  636. #define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
  637. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  638. #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
  639. /**
  640. * Junction Deviation
  641. *
  642. * Use Junction Deviation instead of traditional Jerk Limiting
  643. *
  644. * See:
  645. * https://reprap.org/forum/read.php?1,739819
  646. * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  647. */
  648. //#define JUNCTION_DEVIATION
  649. #if ENABLED(JUNCTION_DEVIATION)
  650. #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge
  651. #endif
  652. /**
  653. * Default Jerk (mm/s)
  654. * Override with M205 X Y Z E
  655. *
  656. * "Jerk" specifies the minimum speed change that requires acceleration.
  657. * When changing speed and direction, if the difference is less than the
  658. * value set here, it may happen instantaneously.
  659. */
  660. #if DISABLED(JUNCTION_DEVIATION)
  661. #define DEFAULT_XJERK 10.0
  662. #define DEFAULT_YJERK 10.0
  663. #define DEFAULT_ZJERK 0.3
  664. #endif
  665. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  666. /**
  667. * S-Curve Acceleration
  668. *
  669. * This option eliminates vibration during printing by fitting a Bézier
  670. * curve to move acceleration, producing much smoother direction changes.
  671. *
  672. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  673. */
  674. //#define S_CURVE_ACCELERATION
  675. //===========================================================================
  676. //============================= Z Probe Options =============================
  677. //===========================================================================
  678. // @section probes
  679. //
  680. // See http://marlinfw.org/docs/configuration/probes.html
  681. //
  682. /**
  683. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  684. *
  685. * Enable this option for a probe connected to the Z Min endstop pin.
  686. */
  687. //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  688. /**
  689. * Z_MIN_PROBE_PIN
  690. *
  691. * Define this pin if the probe is not connected to Z_MIN_PIN.
  692. * If not defined the default pin for the selected MOTHERBOARD
  693. * will be used. Most of the time the default is what you want.
  694. *
  695. * - The simplest option is to use a free endstop connector.
  696. * - Use 5V for powered (usually inductive) sensors.
  697. *
  698. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  699. * - For simple switches connect...
  700. * - normally-closed switches to GND and D32.
  701. * - normally-open switches to 5V and D32.
  702. *
  703. */
  704. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  705. /**
  706. * Probe Type
  707. *
  708. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  709. * Activate one of these to use Auto Bed Leveling below.
  710. */
  711. /**
  712. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  713. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  714. * or (with LCD_BED_LEVELING) the LCD controller.
  715. */
  716. //#define PROBE_MANUALLY
  717. //#define MANUAL_PROBE_START_Z 0.2
  718. /**
  719. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  720. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  721. */
  722. #define FIX_MOUNTED_PROBE
  723. /**
  724. * Z Servo Probe, such as an endstop switch on a rotating arm.
  725. */
  726. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  727. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  728. /**
  729. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  730. */
  731. //#define BLTOUCH
  732. /**
  733. * Touch-MI Probe by hotends.fr
  734. *
  735. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  736. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  737. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  738. *
  739. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  740. * and a minimum Z_HOMING_HEIGHT of 10.
  741. */
  742. //#define TOUCH_MI_PROBE
  743. #if ENABLED(TOUCH_MI_PROBE)
  744. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  745. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  746. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  747. #endif
  748. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  749. //#define SOLENOID_PROBE
  750. // A sled-mounted probe like those designed by Charles Bell.
  751. //#define Z_PROBE_SLED
  752. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  753. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  754. //#define RACK_AND_PINION_PROBE
  755. #if ENABLED(RACK_AND_PINION_PROBE)
  756. #define Z_PROBE_DEPLOY_X X_MIN_POS
  757. #define Z_PROBE_RETRACT_X X_MAX_POS
  758. #endif
  759. //
  760. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  761. //
  762. /**
  763. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  764. * X and Y offsets must be integers.
  765. *
  766. * In the following example the X and Y offsets are both positive:
  767. * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  768. * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  769. *
  770. * +-- BACK ---+
  771. * | |
  772. * L | (+) P | R <-- probe (20,20)
  773. * E | | I
  774. * F | (-) N (+) | G <-- nozzle (10,10)
  775. * T | | H
  776. * | (-) | T
  777. * | |
  778. * O-- FRONT --+
  779. * (0,0)
  780. */
  781. #define X_PROBE_OFFSET_FROM_EXTRUDER -21 // X offset: -left +right [of the nozzle]
  782. #define Y_PROBE_OFFSET_FROM_EXTRUDER 22 // Y offset: -front +behind [the nozzle]
  783. #define Z_PROBE_OFFSET_FROM_EXTRUDER -1.54 // Z offset: -below +above [the nozzle]
  784. // Certain types of probes need to stay away from edges
  785. #define MIN_PROBE_EDGE 20
  786. // X and Y axis travel speed (mm/m) between probes
  787. #define XY_PROBE_SPEED 12000
  788. // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  789. #define Z_PROBE_SPEED_FAST 900
  790. // Feedrate (mm/m) for the "accurate" probe of each point
  791. #define Z_PROBE_SPEED_SLOW 100
  792. /**
  793. * Multiple Probing
  794. *
  795. * You may get improved results by probing 2 or more times.
  796. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  797. *
  798. * A total of 2 does fast/slow probes with a weighted average.
  799. * A total of 3 or more adds more slow probes, taking the average.
  800. */
  801. #define MULTIPLE_PROBING 2
  802. //#define EXTRA_PROBING 1
  803. /**
  804. * Z probes require clearance when deploying, stowing, and moving between
  805. * probe points to avoid hitting the bed and other hardware.
  806. * Servo-mounted probes require extra space for the arm to rotate.
  807. * Inductive probes need space to keep from triggering early.
  808. *
  809. * Use these settings to specify the distance (mm) to raise the probe (or
  810. * lower the bed). The values set here apply over and above any (negative)
  811. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  812. * Only integer values >= 1 are valid here.
  813. *
  814. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  815. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  816. */
  817. #define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow
  818. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  819. #define Z_CLEARANCE_MULTI_PROBE 1 // Z Clearance between multiple probes
  820. #define Z_AFTER_PROBING 5 // Z position after probing is done
  821. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  822. // For M851 give a range for adjusting the Z probe offset
  823. #define Z_PROBE_OFFSET_RANGE_MIN -20
  824. #define Z_PROBE_OFFSET_RANGE_MAX 20
  825. // Enable the M48 repeatability test to test probe accuracy
  826. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  827. // Before deploy/stow pause for user confirmation
  828. //#define PAUSE_BEFORE_DEPLOY_STOW
  829. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  830. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  831. #endif
  832. /**
  833. * Enable one or more of the following if probing seems unreliable.
  834. * Heaters and/or fans can be disabled during probing to minimize electrical
  835. * noise. A delay can also be added to allow noise and vibration to settle.
  836. * These options are most useful for the BLTouch probe, but may also improve
  837. * readings with inductive probes and piezo sensors.
  838. */
  839. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  840. #if ENABLED(PROBING_HEATERS_OFF)
  841. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  842. #endif
  843. //#define PROBING_FANS_OFF // Turn fans off when probing
  844. //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
  845. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  846. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  847. // :{ 0:'Low', 1:'High' }
  848. #define X_ENABLE_ON 0
  849. #define Y_ENABLE_ON 0
  850. #define Z_ENABLE_ON 0
  851. #define E_ENABLE_ON 0 // For all extruders
  852. // Disables axis stepper immediately when it's not being used.
  853. // WARNING: When motors turn off there is a chance of losing position accuracy!
  854. #define DISABLE_X false
  855. #define DISABLE_Y false
  856. #define DISABLE_Z false
  857. // Warn on display about possibly reduced accuracy
  858. //#define DISABLE_REDUCED_ACCURACY_WARNING
  859. // @section extruder
  860. #define DISABLE_E false // For all extruders
  861. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  862. // @section machine
  863. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  864. #define INVERT_X_DIR true
  865. #define INVERT_Y_DIR false
  866. #define INVERT_Z_DIR true
  867. // @section extruder
  868. // For direct drive extruder v9 set to true, for geared extruder set to false.
  869. #define INVERT_E0_DIR false
  870. #define INVERT_E1_DIR false
  871. #define INVERT_E2_DIR false
  872. #define INVERT_E3_DIR false
  873. #define INVERT_E4_DIR false
  874. #define INVERT_E5_DIR false
  875. // @section homing
  876. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  877. //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
  878. #define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  879. // Be sure you have this distance over your Z_MAX_POS in case.
  880. // Direction of endstops when homing; 1=MAX, -1=MIN
  881. // :[-1,1]
  882. #define X_HOME_DIR -1
  883. #define Y_HOME_DIR -1
  884. #define Z_HOME_DIR -1
  885. // @section machine
  886. // The size of the print bed
  887. #define X_BED_SIZE 450
  888. #define Y_BED_SIZE 325
  889. // Travel limits (mm) after homing, corresponding to endstop positions.
  890. #define X_MIN_POS -72
  891. #define Y_MIN_POS -84
  892. #define Z_MIN_POS 0
  893. #define X_MAX_POS X_BED_SIZE
  894. #define Y_MAX_POS Y_BED_SIZE
  895. #define Z_MAX_POS 400
  896. /**
  897. * Software Endstops
  898. *
  899. * - Prevent moves outside the set machine bounds.
  900. * - Individual axes can be disabled, if desired.
  901. * - X and Y only apply to Cartesian robots.
  902. * - Use 'M211' to set software endstops on/off or report current state
  903. */
  904. // Min software endstops constrain movement within minimum coordinate bounds
  905. #define MIN_SOFTWARE_ENDSTOPS
  906. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  907. #define MIN_SOFTWARE_ENDSTOP_X
  908. #define MIN_SOFTWARE_ENDSTOP_Y
  909. #define MIN_SOFTWARE_ENDSTOP_Z
  910. #endif
  911. // Max software endstops constrain movement within maximum coordinate bounds
  912. #define MAX_SOFTWARE_ENDSTOPS
  913. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  914. #define MAX_SOFTWARE_ENDSTOP_X
  915. #define MAX_SOFTWARE_ENDSTOP_Y
  916. #define MAX_SOFTWARE_ENDSTOP_Z
  917. #endif
  918. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  919. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  920. #endif
  921. /**
  922. * Filament Runout Sensors
  923. * Mechanical or opto endstops are used to check for the presence of filament.
  924. *
  925. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  926. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  927. * By default the firmware assumes HIGH=FILAMENT PRESENT.
  928. */
  929. #define FILAMENT_RUNOUT_SENSOR
  930. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  931. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  932. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
  933. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  934. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  935. // Set one or more commands to execute on filament runout.
  936. // (After 'M412 H' Marlin will ask the host to handle the process.)
  937. #define FILAMENT_RUNOUT_SCRIPT "M600"
  938. // After a runout is detected, continue printing this length of filament
  939. // before executing the runout script. Useful for a sensor at the end of
  940. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  941. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  942. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  943. // Enable this option to use an encoder disc that toggles the runout pin
  944. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  945. // large enough to avoid false positives.)
  946. //#define FILAMENT_MOTION_SENSOR
  947. #endif
  948. #endif
  949. //===========================================================================
  950. //=============================== Bed Leveling ==============================
  951. //===========================================================================
  952. // @section calibrate
  953. /**
  954. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  955. * and behavior of G29 will change depending on your selection.
  956. *
  957. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  958. *
  959. * - AUTO_BED_LEVELING_3POINT
  960. * Probe 3 arbitrary points on the bed (that aren't collinear)
  961. * You specify the XY coordinates of all 3 points.
  962. * The result is a single tilted plane. Best for a flat bed.
  963. *
  964. * - AUTO_BED_LEVELING_LINEAR
  965. * Probe several points in a grid.
  966. * You specify the rectangle and the density of sample points.
  967. * The result is a single tilted plane. Best for a flat bed.
  968. *
  969. * - AUTO_BED_LEVELING_BILINEAR
  970. * Probe several points in a grid.
  971. * You specify the rectangle and the density of sample points.
  972. * The result is a mesh, best for large or uneven beds.
  973. *
  974. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  975. * A comprehensive bed leveling system combining the features and benefits
  976. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  977. * Validation and Mesh Editing systems.
  978. *
  979. * - MESH_BED_LEVELING
  980. * Probe a grid manually
  981. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  982. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  983. * leveling in steps so you can manually adjust the Z height at each grid-point.
  984. * With an LCD controller the process is guided step-by-step.
  985. */
  986. //#define AUTO_BED_LEVELING_3POINT
  987. #define AUTO_BED_LEVELING_LINEAR
  988. //#define AUTO_BED_LEVELING_BILINEAR
  989. //#define AUTO_BED_LEVELING_UBL
  990. //#define MESH_BED_LEVELING
  991. /**
  992. * Normally G28 leaves leveling disabled on completion. Enable
  993. * this option to have G28 restore the prior leveling state.
  994. */
  995. //#define RESTORE_LEVELING_AFTER_G28
  996. /**
  997. * Enable detailed logging of G28, G29, M48, etc.
  998. * Turn on with the command 'M111 S32'.
  999. * NOTE: Requires a lot of PROGMEM!
  1000. */
  1001. //#define DEBUG_LEVELING_FEATURE
  1002. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1003. // Gradually reduce leveling correction until a set height is reached,
  1004. // at which point movement will be level to the machine's XY plane.
  1005. // The height can be set with M420 Z<height>
  1006. #define ENABLE_LEVELING_FADE_HEIGHT
  1007. // For Cartesian machines, instead of dividing moves on mesh boundaries,
  1008. // split up moves into short segments like a Delta. This follows the
  1009. // contours of the bed more closely than edge-to-edge straight moves.
  1010. #define SEGMENT_LEVELED_MOVES
  1011. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1012. /**
  1013. * Enable the G26 Mesh Validation Pattern tool.
  1014. */
  1015. //#define G26_MESH_VALIDATION
  1016. #if ENABLED(G26_MESH_VALIDATION)
  1017. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  1018. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  1019. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  1020. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  1021. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
  1022. #endif
  1023. #endif
  1024. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1025. // Set the number of grid points per dimension.
  1026. #define GRID_MAX_POINTS_X 5
  1027. #define GRID_MAX_POINTS_Y 3
  1028. // Set the boundaries for probing (where the probe can reach).
  1029. //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
  1030. //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
  1031. //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
  1032. //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
  1033. // Probe along the Y axis, advancing X after each column
  1034. //#define PROBE_Y_FIRST
  1035. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1036. // Beyond the probed grid, continue the implied tilt?
  1037. // Default is to maintain the height of the nearest edge.
  1038. //#define EXTRAPOLATE_BEYOND_GRID
  1039. //
  1040. // Experimental Subdivision of the grid by Catmull-Rom method.
  1041. // Synthesizes intermediate points to produce a more detailed mesh.
  1042. //
  1043. //#define ABL_BILINEAR_SUBDIVISION
  1044. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1045. // Number of subdivisions between probe points
  1046. #define BILINEAR_SUBDIVISIONS 3
  1047. #endif
  1048. #endif
  1049. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1050. //===========================================================================
  1051. //========================= Unified Bed Leveling ============================
  1052. //===========================================================================
  1053. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1054. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1055. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1056. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1057. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  1058. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  1059. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  1060. // as the Z-Height correction value.
  1061. #elif ENABLED(MESH_BED_LEVELING)
  1062. //===========================================================================
  1063. //=================================== Mesh ==================================
  1064. //===========================================================================
  1065. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  1066. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  1067. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1068. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  1069. #endif // BED_LEVELING
  1070. /**
  1071. * Points to probe for all 3-point Leveling procedures.
  1072. * Override if the automatically selected points are inadequate.
  1073. */
  1074. #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
  1075. //#define PROBE_PT_1_X 15
  1076. //#define PROBE_PT_1_Y 180
  1077. //#define PROBE_PT_2_X 15
  1078. //#define PROBE_PT_2_Y 20
  1079. //#define PROBE_PT_3_X 170
  1080. //#define PROBE_PT_3_Y 20
  1081. #endif
  1082. /**
  1083. * Add a bed leveling sub-menu for ABL or MBL.
  1084. * Include a guided procedure if manual probing is enabled.
  1085. */
  1086. //#define LCD_BED_LEVELING
  1087. #if ENABLED(LCD_BED_LEVELING)
  1088. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  1089. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  1090. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  1091. #endif
  1092. // Add a menu item to move between bed corners for manual bed adjustment
  1093. //#define LEVEL_BED_CORNERS
  1094. #if ENABLED(LEVEL_BED_CORNERS)
  1095. #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
  1096. #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
  1097. #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  1098. //#define LEVEL_CENTER_TOO // Move to the center after the last corner
  1099. #endif
  1100. /**
  1101. * Commands to execute at the end of G29 probing.
  1102. * Useful to retract or move the Z probe out of the way.
  1103. */
  1104. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1105. // @section homing
  1106. // The center of the bed is at (X=0, Y=0)
  1107. //#define BED_CENTER_AT_0_0
  1108. // Manually set the home position. Leave these undefined for automatic settings.
  1109. // For DELTA this is the top-center of the Cartesian print volume.
  1110. //#define MANUAL_X_HOME_POS 0
  1111. //#define MANUAL_Y_HOME_POS 0
  1112. //#define MANUAL_Z_HOME_POS 0
  1113. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1114. //
  1115. // With this feature enabled:
  1116. //
  1117. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1118. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1119. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1120. // - Prevent Z homing when the Z probe is outside bed area.
  1121. //
  1122. //#define Z_SAFE_HOMING
  1123. #if ENABLED(Z_SAFE_HOMING)
  1124. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  1125. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  1126. #endif
  1127. // Homing speeds (mm/m)
  1128. #define HOMING_FEEDRATE_XY (6000)
  1129. #define HOMING_FEEDRATE_Z (900)
  1130. // Validate that endstops are triggered on homing moves
  1131. #define VALIDATE_HOMING_ENDSTOPS
  1132. // @section calibrate
  1133. /**
  1134. * Bed Skew Compensation
  1135. *
  1136. * This feature corrects for misalignment in the XYZ axes.
  1137. *
  1138. * Take the following steps to get the bed skew in the XY plane:
  1139. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1140. * 2. For XY_DIAG_AC measure the diagonal A to C
  1141. * 3. For XY_DIAG_BD measure the diagonal B to D
  1142. * 4. For XY_SIDE_AD measure the edge A to D
  1143. *
  1144. * Marlin automatically computes skew factors from these measurements.
  1145. * Skew factors may also be computed and set manually:
  1146. *
  1147. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1148. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1149. *
  1150. * If desired, follow the same procedure for XZ and YZ.
  1151. * Use these diagrams for reference:
  1152. *
  1153. * Y Z Z
  1154. * ^ B-------C ^ B-------C ^ B-------C
  1155. * | / / | / / | / /
  1156. * | / / | / / | / /
  1157. * | A-------D | A-------D | A-------D
  1158. * +-------------->X +-------------->X +-------------->Y
  1159. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  1160. */
  1161. //#define SKEW_CORRECTION
  1162. #if ENABLED(SKEW_CORRECTION)
  1163. // Input all length measurements here:
  1164. #define XY_DIAG_AC 282.8427124746
  1165. #define XY_DIAG_BD 282.8427124746
  1166. #define XY_SIDE_AD 200
  1167. // Or, set the default skew factors directly here
  1168. // to override the above measurements:
  1169. #define XY_SKEW_FACTOR 0.0
  1170. //#define SKEW_CORRECTION_FOR_Z
  1171. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1172. #define XZ_DIAG_AC 282.8427124746
  1173. #define XZ_DIAG_BD 282.8427124746
  1174. #define YZ_DIAG_AC 282.8427124746
  1175. #define YZ_DIAG_BD 282.8427124746
  1176. #define YZ_SIDE_AD 200
  1177. #define XZ_SKEW_FACTOR 0.0
  1178. #define YZ_SKEW_FACTOR 0.0
  1179. #endif
  1180. // Enable this option for M852 to set skew at runtime
  1181. //#define SKEW_CORRECTION_GCODE
  1182. #endif
  1183. //=============================================================================
  1184. //============================= Additional Features ===========================
  1185. //=============================================================================
  1186. // @section extras
  1187. /**
  1188. * EEPROM
  1189. *
  1190. * Persistent storage to preserve configurable settings across reboots.
  1191. *
  1192. * M500 - Store settings to EEPROM.
  1193. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  1194. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  1195. */
  1196. #define EEPROM_SETTINGS // Persistent storage with M500 and M501
  1197. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  1198. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1199. #if ENABLED(EEPROM_SETTINGS)
  1200. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  1201. #endif
  1202. //
  1203. // Host Keepalive
  1204. //
  1205. // When enabled Marlin will send a busy status message to the host
  1206. // every couple of seconds when it can't accept commands.
  1207. //
  1208. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  1209. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  1210. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  1211. //
  1212. // M100 Free Memory Watcher
  1213. //
  1214. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  1215. //
  1216. // G20/G21 Inch mode support
  1217. //
  1218. //#define INCH_MODE_SUPPORT
  1219. //
  1220. // M149 Set temperature units support
  1221. //
  1222. //#define TEMPERATURE_UNITS_SUPPORT
  1223. // @section temperature
  1224. // Preheat Constants
  1225. #define PREHEAT_1_LABEL "PLA"
  1226. #define PREHEAT_1_TEMP_HOTEND 180
  1227. #define PREHEAT_1_TEMP_BED 70
  1228. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  1229. #define PREHEAT_2_LABEL "ABS"
  1230. #define PREHEAT_2_TEMP_HOTEND 240
  1231. #define PREHEAT_2_TEMP_BED 110
  1232. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  1233. /**
  1234. * Nozzle Park
  1235. *
  1236. * Park the nozzle at the given XYZ position on idle or G27.
  1237. *
  1238. * The "P" parameter controls the action applied to the Z axis:
  1239. *
  1240. * P0 (Default) If Z is below park Z raise the nozzle.
  1241. * P1 Raise the nozzle always to Z-park height.
  1242. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1243. */
  1244. #define NOZZLE_PARK_FEATURE
  1245. #if ENABLED(NOZZLE_PARK_FEATURE)
  1246. // Specify a park position as { X, Y, Z_raise }
  1247. #define NOZZLE_PARK_POINT { 225, -50, 5 }
  1248. #define NOZZLE_PARK_XY_FEEDRATE 150 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  1249. #define NOZZLE_PARK_Z_FEEDRATE 15 // (mm/s) Z axis feedrate (not used for delta printers)
  1250. #endif
  1251. /**
  1252. * Clean Nozzle Feature -- EXPERIMENTAL
  1253. *
  1254. * Adds the G12 command to perform a nozzle cleaning process.
  1255. *
  1256. * Parameters:
  1257. * P Pattern
  1258. * S Strokes / Repetitions
  1259. * T Triangles (P1 only)
  1260. *
  1261. * Patterns:
  1262. * P0 Straight line (default). This process requires a sponge type material
  1263. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1264. * between the start / end points.
  1265. *
  1266. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1267. * number of zig-zag triangles to do. "S" defines the number of strokes.
  1268. * Zig-zags are done in whichever is the narrower dimension.
  1269. * For example, "G12 P1 S1 T3" will execute:
  1270. *
  1271. * --
  1272. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  1273. * | | / \ / \ / \ |
  1274. * A | | / \ / \ / \ |
  1275. * | | / \ / \ / \ |
  1276. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  1277. * -- +--------------------------------+
  1278. * |________|_________|_________|
  1279. * T1 T2 T3
  1280. *
  1281. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1282. * "R" specifies the radius. "S" specifies the stroke count.
  1283. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1284. *
  1285. * Caveats: The ending Z should be the same as starting Z.
  1286. * Attention: EXPERIMENTAL. G-code arguments may change.
  1287. *
  1288. */
  1289. #define NOZZLE_CLEAN_FEATURE
  1290. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1291. // Default number of pattern repetitions
  1292. #define NOZZLE_CLEAN_STROKES 4
  1293. // Default number of triangles
  1294. #define NOZZLE_CLEAN_TRIANGLES 2
  1295. // Specify positions as { X, Y, Z } . Leave Z blank to not change the Z position
  1296. #define NOZZLE_CLEAN_START_POINT { -37, -67, }
  1297. #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) }
  1298. // Circular pattern radius
  1299. #define NOZZLE_CLEAN_CIRCLE_RADIUS 8
  1300. // Circular pattern circle fragments number
  1301. #define NOZZLE_CLEAN_CIRCLE_FN 10
  1302. // Middle point of circle
  1303. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1304. // Move the nozzle to the initial position after cleaning
  1305. #define NOZZLE_CLEAN_GOBACK
  1306. // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
  1307. #define NOZZLE_CLEAN_NO_Z
  1308. #endif
  1309. /**
  1310. * Print Job Timer
  1311. *
  1312. * Automatically start and stop the print job timer on M104/M109/M190.
  1313. *
  1314. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1315. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1316. * M190 (bed, wait) - high temp = start timer, low temp = none
  1317. *
  1318. * The timer can also be controlled with the following commands:
  1319. *
  1320. * M75 - Start the print job timer
  1321. * M76 - Pause the print job timer
  1322. * M77 - Stop the print job timer
  1323. */
  1324. #define PRINTJOB_TIMER_AUTOSTART
  1325. /**
  1326. * Print Counter
  1327. *
  1328. * Track statistical data such as:
  1329. *
  1330. * - Total print jobs
  1331. * - Total successful print jobs
  1332. * - Total failed print jobs
  1333. * - Total time printing
  1334. *
  1335. * View the current statistics with M78.
  1336. */
  1337. #define PRINTCOUNTER
  1338. //=============================================================================
  1339. //============================= LCD and SD support ============================
  1340. //=============================================================================
  1341. // @section lcd
  1342. /**
  1343. * LCD LANGUAGE
  1344. *
  1345. * Select the language to display on the LCD. These languages are available:
  1346. *
  1347. * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, jp-kana,
  1348. * ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  1349. *
  1350. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  1351. */
  1352. #define LCD_LANGUAGE en
  1353. /**
  1354. * LCD Character Set
  1355. *
  1356. * Note: This option is NOT applicable to Graphical Displays.
  1357. *
  1358. * All character-based LCDs provide ASCII plus one of these
  1359. * language extensions:
  1360. *
  1361. * - JAPANESE ... the most common
  1362. * - WESTERN ... with more accented characters
  1363. * - CYRILLIC ... for the Russian language
  1364. *
  1365. * To determine the language extension installed on your controller:
  1366. *
  1367. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1368. * - Click the controller to view the LCD menu
  1369. * - The LCD will display Japanese, Western, or Cyrillic text
  1370. *
  1371. * See http://marlinfw.org/docs/development/lcd_language.html
  1372. *
  1373. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1374. */
  1375. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1376. /**
  1377. * Info Screen Style (0:Classic, 1:Prusa)
  1378. *
  1379. * :[0:'Classic', 1:'Prusa']
  1380. */
  1381. #define LCD_INFO_SCREEN_STYLE 0
  1382. /**
  1383. * SD CARD
  1384. *
  1385. * SD Card support is disabled by default. If your controller has an SD slot,
  1386. * you must uncomment the following option or it won't work.
  1387. *
  1388. */
  1389. #define SDSUPPORT
  1390. /**
  1391. * SD CARD: SPI SPEED
  1392. *
  1393. * Enable one of the following items for a slower SPI transfer speed.
  1394. * This may be required to resolve "volume init" errors.
  1395. */
  1396. //#define SPI_SPEED SPI_HALF_SPEED
  1397. //#define SPI_SPEED SPI_QUARTER_SPEED
  1398. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1399. /**
  1400. * SD CARD: ENABLE CRC
  1401. *
  1402. * Use CRC checks and retries on the SD communication.
  1403. */
  1404. //#define SD_CHECK_AND_RETRY
  1405. /**
  1406. * LCD Menu Items
  1407. *
  1408. * Disable all menus and only display the Status Screen, or
  1409. * just remove some extraneous menu items to recover space.
  1410. */
  1411. //#define NO_LCD_MENUS
  1412. //#define SLIM_LCD_MENUS
  1413. //
  1414. // ENCODER SETTINGS
  1415. //
  1416. // This option overrides the default number of encoder pulses needed to
  1417. // produce one step. Should be increased for high-resolution encoders.
  1418. //
  1419. //#define ENCODER_PULSES_PER_STEP 4
  1420. //
  1421. // Use this option to override the number of step signals required to
  1422. // move between next/prev menu items.
  1423. //
  1424. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  1425. /**
  1426. * Encoder Direction Options
  1427. *
  1428. * Test your encoder's behavior first with both options disabled.
  1429. *
  1430. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1431. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1432. * Reversed Value Editing only? Enable BOTH options.
  1433. */
  1434. //
  1435. // This option reverses the encoder direction everywhere.
  1436. //
  1437. // Set this option if CLOCKWISE causes values to DECREASE
  1438. //
  1439. //#define REVERSE_ENCODER_DIRECTION
  1440. //
  1441. // This option reverses the encoder direction for navigating LCD menus.
  1442. //
  1443. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1444. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1445. //
  1446. //#define REVERSE_MENU_DIRECTION
  1447. //
  1448. // This option reverses the encoder direction for Select Screen.
  1449. //
  1450. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  1451. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  1452. //
  1453. //#define REVERSE_SELECT_DIRECTION
  1454. //
  1455. // Individual Axis Homing
  1456. //
  1457. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1458. //
  1459. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1460. //
  1461. // SPEAKER/BUZZER
  1462. //
  1463. // If you have a speaker that can produce tones, enable it here.
  1464. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1465. //
  1466. #define SPEAKER
  1467. //
  1468. // The duration and frequency for the UI feedback sound.
  1469. // Set these to 0 to disable audio feedback in the LCD menus.
  1470. //
  1471. // Note: Test audio output with the G-Code:
  1472. // M300 S<frequency Hz> P<duration ms>
  1473. //
  1474. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  1475. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  1476. //=============================================================================
  1477. //======================== LCD / Controller Selection =========================
  1478. //======================== (Character-based LCDs) =========================
  1479. //=============================================================================
  1480. //
  1481. // RepRapDiscount Smart Controller.
  1482. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1483. //
  1484. // Note: Usually sold with a white PCB.
  1485. //
  1486. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1487. //
  1488. // Original RADDS LCD Display+Encoder+SDCardReader
  1489. // http://doku.radds.org/dokumentation/lcd-display/
  1490. //
  1491. //#define RADDS_DISPLAY
  1492. //
  1493. // ULTIMAKER Controller.
  1494. //
  1495. //#define ULTIMAKERCONTROLLER
  1496. //
  1497. // ULTIPANEL as seen on Thingiverse.
  1498. //
  1499. //#define ULTIPANEL
  1500. //
  1501. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1502. // http://reprap.org/wiki/PanelOne
  1503. //
  1504. //#define PANEL_ONE
  1505. //
  1506. // GADGETS3D G3D LCD/SD Controller
  1507. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1508. //
  1509. // Note: Usually sold with a blue PCB.
  1510. //
  1511. //#define G3D_PANEL
  1512. //
  1513. // RigidBot Panel V1.0
  1514. // http://www.inventapart.com/
  1515. //
  1516. //#define RIGIDBOT_PANEL
  1517. //
  1518. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1519. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1520. //
  1521. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1522. //
  1523. // ANET and Tronxy 20x4 Controller
  1524. //
  1525. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1526. // This LCD is known to be susceptible to electrical interference
  1527. // which scrambles the display. Pressing any button clears it up.
  1528. // This is a LCD2004 display with 5 analog buttons.
  1529. //
  1530. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1531. //
  1532. //#define ULTRA_LCD
  1533. //=============================================================================
  1534. //======================== LCD / Controller Selection =========================
  1535. //===================== (I2C and Shift-Register LCDs) =====================
  1536. //=============================================================================
  1537. //
  1538. // CONTROLLER TYPE: I2C
  1539. //
  1540. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1541. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1542. //
  1543. //
  1544. // Elefu RA Board Control Panel
  1545. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1546. //
  1547. //#define RA_CONTROL_PANEL
  1548. //
  1549. // Sainsmart (YwRobot) LCD Displays
  1550. //
  1551. // These require F.Malpartida's LiquidCrystal_I2C library
  1552. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1553. //
  1554. //#define LCD_SAINSMART_I2C_1602
  1555. //#define LCD_SAINSMART_I2C_2004
  1556. //
  1557. // Generic LCM1602 LCD adapter
  1558. //
  1559. //#define LCM1602
  1560. //
  1561. // PANELOLU2 LCD with status LEDs,
  1562. // separate encoder and click inputs.
  1563. //
  1564. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1565. // For more info: https://github.com/lincomatic/LiquidTWI2
  1566. //
  1567. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1568. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1569. //
  1570. //#define LCD_I2C_PANELOLU2
  1571. //
  1572. // Panucatt VIKI LCD with status LEDs,
  1573. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1574. //
  1575. //#define LCD_I2C_VIKI
  1576. //
  1577. // CONTROLLER TYPE: Shift register panels
  1578. //
  1579. //
  1580. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1581. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1582. //
  1583. //#define SAV_3DLCD
  1584. //
  1585. // 3-wire SR LCD with strobe using 74HC4094
  1586. // https://github.com/mikeshub/SailfishLCD
  1587. // Uses the code directly from Sailfish
  1588. //
  1589. //#define FF_INTERFACEBOARD
  1590. //=============================================================================
  1591. //======================= LCD / Controller Selection =======================
  1592. //========================= (Graphical LCDs) ========================
  1593. //=============================================================================
  1594. //
  1595. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  1596. //
  1597. // IMPORTANT: The U8glib library is required for Graphical Display!
  1598. // https://github.com/olikraus/U8glib_Arduino
  1599. //
  1600. //
  1601. // RepRapDiscount FULL GRAPHIC Smart Controller
  1602. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1603. //
  1604. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1605. //
  1606. // ReprapWorld Graphical LCD
  1607. // https://reprapworld.com/?products_details&products_id/1218
  1608. //
  1609. //#define REPRAPWORLD_GRAPHICAL_LCD
  1610. //
  1611. // Activate one of these if you have a Panucatt Devices
  1612. // Viki 2.0 or mini Viki with Graphic LCD
  1613. // http://panucatt.com
  1614. //
  1615. //#define VIKI2
  1616. //#define miniVIKI
  1617. //
  1618. // MakerLab Mini Panel with graphic
  1619. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1620. //
  1621. //#define MINIPANEL
  1622. //
  1623. // MaKr3d Makr-Panel with graphic controller and SD support.
  1624. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1625. //
  1626. //#define MAKRPANEL
  1627. //
  1628. // Adafruit ST7565 Full Graphic Controller.
  1629. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1630. //
  1631. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1632. //
  1633. // BQ LCD Smart Controller shipped by
  1634. // default with the BQ Hephestos 2 and Witbox 2.
  1635. //
  1636. //#define BQ_LCD_SMART_CONTROLLER
  1637. //
  1638. // Cartesio UI
  1639. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1640. //
  1641. //#define CARTESIO_UI
  1642. //
  1643. // LCD for Melzi Card with Graphical LCD
  1644. //
  1645. //#define LCD_FOR_MELZI
  1646. //
  1647. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  1648. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  1649. //
  1650. //#define ULTI_CONTROLLER
  1651. //
  1652. // MKS MINI12864 with graphic controller and SD support
  1653. // https://reprap.org/wiki/MKS_MINI_12864
  1654. //
  1655. //#define MKS_MINI_12864
  1656. //
  1657. // FYSETC variant of the MINI12864 graphic controller with SD support
  1658. // https://wiki.fysetc.com/Mini12864_Panel/
  1659. //
  1660. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  1661. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  1662. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  1663. //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight
  1664. //
  1665. // Factory display for Creality CR-10
  1666. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1667. //
  1668. // This is RAMPS-compatible using a single 10-pin connector.
  1669. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1670. //
  1671. //#define CR10_STOCKDISPLAY
  1672. //
  1673. // ANET and Tronxy Graphical Controller
  1674. //
  1675. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1676. // A clone of the RepRapDiscount full graphics display but with
  1677. // different pins/wiring (see pins_ANET_10.h).
  1678. //
  1679. //#define ANET_FULL_GRAPHICS_LCD
  1680. //
  1681. // AZSMZ 12864 LCD with SD
  1682. // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
  1683. //
  1684. //#define AZSMZ_12864
  1685. //
  1686. // Silvergate GLCD controller
  1687. // http://github.com/android444/Silvergate
  1688. //
  1689. //#define SILVER_GATE_GLCD_CONTROLLER
  1690. //=============================================================================
  1691. //============================== OLED Displays ==============================
  1692. //=============================================================================
  1693. //
  1694. // SSD1306 OLED full graphics generic display
  1695. //
  1696. //#define U8GLIB_SSD1306
  1697. //
  1698. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1699. //
  1700. //#define SAV_3DGLCD
  1701. #if ENABLED(SAV_3DGLCD)
  1702. #define U8GLIB_SSD1306
  1703. //#define U8GLIB_SH1106
  1704. #endif
  1705. //
  1706. // TinyBoy2 128x64 OLED / Encoder Panel
  1707. //
  1708. //#define OLED_PANEL_TINYBOY2
  1709. //
  1710. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1711. // http://reprap.org/wiki/MKS_12864OLED
  1712. //
  1713. // Tiny, but very sharp OLED display
  1714. //
  1715. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  1716. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  1717. //
  1718. // Einstart S OLED SSD1306
  1719. //
  1720. //#define U8GLIB_SH1106_EINSTART
  1721. //
  1722. // Overlord OLED display/controller with i2c buzzer and LEDs
  1723. //
  1724. //#define OVERLORD_OLED
  1725. //=============================================================================
  1726. //========================== Extensible UI Displays ===========================
  1727. //=============================================================================
  1728. //
  1729. // DGUS Touch Display with DWIN OS
  1730. //
  1731. //#define DGUS_LCD
  1732. //
  1733. // Touch-screen LCD for Malyan M200 printers
  1734. //
  1735. //#define MALYAN_LCD
  1736. //
  1737. // Third-party or vendor-customized controller interfaces.
  1738. // Sources should be installed in 'src/lcd/extensible_ui'.
  1739. //
  1740. //#define EXTENSIBLE_UI
  1741. //=============================================================================
  1742. //=============================== Graphical TFTs ==============================
  1743. //=============================================================================
  1744. //
  1745. // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
  1746. //
  1747. //#define FSMC_GRAPHICAL_TFT
  1748. //=============================================================================
  1749. //============================ Other Controllers ============================
  1750. //=============================================================================
  1751. //
  1752. // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  1753. //
  1754. //#define TOUCH_BUTTONS
  1755. #if ENABLED(TOUCH_BUTTONS)
  1756. #define XPT2046_X_CALIBRATION 12316
  1757. #define XPT2046_Y_CALIBRATION -8981
  1758. #define XPT2046_X_OFFSET -43
  1759. #define XPT2046_Y_OFFSET 257
  1760. #endif
  1761. //
  1762. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1763. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1764. //
  1765. //#define REPRAPWORLD_KEYPAD
  1766. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  1767. //=============================================================================
  1768. //=============================== Extra Features ==============================
  1769. //=============================================================================
  1770. // @section extras
  1771. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1772. //#define FAST_PWM_FAN
  1773. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1774. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1775. // is too low, you should also increment SOFT_PWM_SCALE.
  1776. //#define FAN_SOFT_PWM
  1777. // Incrementing this by 1 will double the software PWM frequency,
  1778. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1779. // However, control resolution will be halved for each increment;
  1780. // at zero value, there are 128 effective control positions.
  1781. // :[0,1,2,3,4,5,6,7]
  1782. #define SOFT_PWM_SCALE 0
  1783. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1784. // be used to mitigate the associated resolution loss. If enabled,
  1785. // some of the PWM cycles are stretched so on average the desired
  1786. // duty cycle is attained.
  1787. //#define SOFT_PWM_DITHER
  1788. // Temperature status LEDs that display the hotend and bed temperature.
  1789. // If all hotends, bed temperature, and target temperature are under 54C
  1790. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1791. #define TEMP_STAT_LEDS
  1792. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1793. //#define SF_ARC_FIX
  1794. // Support for the BariCUDA Paste Extruder
  1795. //#define BARICUDA
  1796. // Support for BlinkM/CyzRgb
  1797. //#define BLINKM
  1798. // Support for PCA9632 PWM LED driver
  1799. //#define PCA9632
  1800. // Support for PCA9533 PWM LED driver
  1801. // https://github.com/mikeshub/SailfishRGB_LED
  1802. //#define PCA9533
  1803. /**
  1804. * RGB LED / LED Strip Control
  1805. *
  1806. * Enable support for an RGB LED connected to 5V digital pins, or
  1807. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1808. *
  1809. * Adds the M150 command to set the LED (or LED strip) color.
  1810. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1811. * luminance values can be set from 0 to 255.
  1812. * For Neopixel LED an overall brightness parameter is also available.
  1813. *
  1814. * *** CAUTION ***
  1815. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  1816. * as the Arduino cannot handle the current the LEDs will require.
  1817. * Failure to follow this precaution can destroy your Arduino!
  1818. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1819. * more current than the Arduino 5V linear regulator can produce.
  1820. * *** CAUTION ***
  1821. *
  1822. * LED Type. Enable only one of the following two options.
  1823. *
  1824. */
  1825. //#define RGB_LED
  1826. //#define RGBW_LED
  1827. #if EITHER(RGB_LED, RGBW_LED)
  1828. //#define RGB_LED_R_PIN 34
  1829. //#define RGB_LED_G_PIN 43
  1830. //#define RGB_LED_B_PIN 35
  1831. //#define RGB_LED_W_PIN -1
  1832. #endif
  1833. // Support for Adafruit Neopixel LED driver
  1834. //#define NEOPIXEL_LED
  1835. #if ENABLED(NEOPIXEL_LED)
  1836. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1837. #define NEOPIXEL_PIN 4 // LED driving pin
  1838. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  1839. //#define NEOPIXEL2_PIN 5
  1840. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
  1841. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1842. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1843. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1844. // Use a single Neopixel LED for static (background) lighting
  1845. //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
  1846. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  1847. #endif
  1848. /**
  1849. * Printer Event LEDs
  1850. *
  1851. * During printing, the LEDs will reflect the printer status:
  1852. *
  1853. * - Gradually change from blue to violet as the heated bed gets to target temp
  1854. * - Gradually change from violet to red as the hotend gets to temperature
  1855. * - Change to white to illuminate work surface
  1856. * - Change to green once print has finished
  1857. * - Turn off after the print has finished and the user has pushed a button
  1858. */
  1859. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  1860. #define PRINTER_EVENT_LEDS
  1861. #endif
  1862. /**
  1863. * R/C SERVO support
  1864. * Sponsored by TrinityLabs, Reworked by codexmas
  1865. */
  1866. /**
  1867. * Number of servos
  1868. *
  1869. * For some servo-related options NUM_SERVOS will be set automatically.
  1870. * Set this manually if there are extra servos needing manual control.
  1871. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1872. */
  1873. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1874. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1875. // 300ms is a good value but you can try less delay.
  1876. // If the servo can't reach the requested position, increase it.
  1877. #define SERVO_DELAY { 300 }
  1878. // Only power servos during movement, otherwise leave off to prevent jitter
  1879. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1880. // Allow servo angle to be edited and saved to EEPROM
  1881. //#define EDITABLE_SERVO_ANGLES