My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Você não pode selecionar mais de 25 tópicos Os tópicos devem começar com uma letra ou um número, podem incluir traços ('-') e podem ter até 35 caracteres.

SanityCheck.h 52KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * SanityCheck.h
  24. *
  25. * Test configuration values for errors at compile-time.
  26. */
  27. /**
  28. * Require gcc 4.7 or newer (first included with Arduino 1.6.8) for C++11 features.
  29. */
  30. #if __cplusplus < 201103L
  31. #error "Marlin requires C++11 support (gcc >= 4.7, Arduino IDE >= 1.6.8). Please upgrade your toolchain."
  32. #endif
  33. /**
  34. * We try our best to include sanity checks for all changed configuration
  35. * directives because users have a tendency to use outdated config files with
  36. * the bleeding-edge source code, but sometimes this is not enough. This check
  37. * forces a minimum config file revision. Otherwise Marlin will not build.
  38. */
  39. #if ! defined(CONFIGURATION_H_VERSION) || CONFIGURATION_H_VERSION < REQUIRED_CONFIGURATION_H_VERSION
  40. #error "You are using an old Configuration.h file, update it before building Marlin."
  41. #endif
  42. #if ! defined(CONFIGURATION_ADV_H_VERSION) || CONFIGURATION_ADV_H_VERSION < REQUIRED_CONFIGURATION_ADV_H_VERSION
  43. #error "You are using an old Configuration_adv.h file, update it before building Marlin."
  44. #endif
  45. /**
  46. * Warnings for old configurations
  47. */
  48. #if !defined(X_BED_SIZE) || !defined(Y_BED_SIZE)
  49. #error "X_BED_SIZE and Y_BED_SIZE are now required! Please update your configuration."
  50. #elif WATCH_TEMP_PERIOD > 500
  51. #error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds."
  52. #elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD))
  53. #error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS."
  54. #elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD)
  55. #error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED."
  56. #elif (CORE_IS_XZ || CORE_IS_YZ) && ENABLED(Z_LATE_ENABLE)
  57. #error "Z_LATE_ENABLE can't be used with COREXZ, COREZX, COREYZ, or COREZY."
  58. #elif defined(X_HOME_RETRACT_MM)
  59. #error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
  60. #elif defined(SDCARDDETECTINVERTED)
  61. #error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration."
  62. #elif defined(BTENABLED)
  63. #error "BTENABLED is now BLUETOOTH. Please update your configuration."
  64. #elif defined(CUSTOM_MENDEL_NAME)
  65. #error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration."
  66. #elif defined(HAS_AUTOMATIC_VERSIONING)
  67. #error "HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration."
  68. #elif defined(SDSLOW)
  69. #error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead."
  70. #elif defined(SDEXTRASLOW)
  71. #error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead."
  72. #elif defined(FILAMENT_SENSOR)
  73. #error "FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead."
  74. #elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
  75. #error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead."
  76. #elif ENABLED(Z_DUAL_ENDSTOPS) && !defined(Z2_USE_ENDSTOP)
  77. #error "Z_DUAL_ENDSTOPS settings are simplified. Just set Z2_USE_ENDSTOP to the endstop you want to repurpose for Z2."
  78. #elif defined(LANGUAGE_INCLUDE)
  79. #error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration."
  80. #elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y)
  81. #error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead."
  82. #elif defined(PID_PARAMS_PER_EXTRUDER)
  83. #error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead."
  84. #elif defined(EXTRUDER_WATTS) || defined(BED_WATTS)
  85. #error "EXTRUDER_WATTS and BED_WATTS are deprecated. Remove them from your configuration."
  86. #elif defined(SERVO_ENDSTOP_ANGLES)
  87. #error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead."
  88. #elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR)
  89. #error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed."
  90. #elif defined(DEFAULT_XYJERK)
  91. #error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead."
  92. #elif defined(XY_TRAVEL_SPEED)
  93. #error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
  94. #elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
  95. #error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead."
  96. #elif defined(SERVO_DEACTIVATION_DELAY)
  97. #error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
  98. #elif ENABLED(FILAMENTCHANGEENABLE)
  99. #error "FILAMENTCHANGEENABLE is now ADVANCED_PAUSE_FEATURE. Please update your configuration."
  100. #elif ENABLED(FILAMENT_CHANGE_FEATURE)
  101. #error "FILAMENT_CHANGE_FEATURE is now ADVANCED_PAUSE_FEATURE. Please update your configuration."
  102. #elif ENABLED(FILAMENT_CHANGE_X_POS)
  103. #error "FILAMENT_CHANGE_X_POS is now PAUSE_PARK_X_POS. Please update your configuration."
  104. #elif ENABLED(FILAMENT_CHANGE_Y_POS)
  105. #error "FILAMENT_CHANGE_Y_POS is now PAUSE_PARK_Y_POS. Please update your configuration."
  106. #elif ENABLED(FILAMENT_CHANGE_Z_ADD)
  107. #error "FILAMENT_CHANGE_Z_ADD is now PAUSE_PARK_Z_ADD. Please update your configuration."
  108. #elif ENABLED(FILAMENT_CHANGE_XY_FEEDRATE)
  109. #error "FILAMENT_CHANGE_XY_FEEDRATE is now PAUSE_PARK_XY_FEEDRATE. Please update your configuration."
  110. #elif ENABLED(FILAMENT_CHANGE_Z_FEEDRATE)
  111. #error "FILAMENT_CHANGE_Z_FEEDRATE is now PAUSE_PARK_Z_FEEDRATE. Please update your configuration."
  112. #elif ENABLED(FILAMENT_CHANGE_RETRACT_FEEDRATE)
  113. #error "FILAMENT_CHANGE_RETRACT_FEEDRATE is now PAUSE_PARK_RETRACT_FEEDRATE. Please update your configuration."
  114. #elif ENABLED(FILAMENT_CHANGE_RETRACT_LENGTH)
  115. #error "FILAMENT_CHANGE_RETRACT_LENGTH is now PAUSE_PARK_RETRACT_LENGTH. Please update your configuration."
  116. #elif ENABLED(FILAMENT_CHANGE_EXTRUDE_FEEDRATE)
  117. #error "FILAMENT_CHANGE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_EXTRUDE_FEEDRATE. Please update your configuration."
  118. #elif ENABLED(FILAMENT_CHANGE_EXTRUDE_LENGTH)
  119. #error "FILAMENT_CHANGE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_EXTRUDE_LENGTH. Please update your configuration."
  120. #elif ENABLED(FILAMENT_CHANGE_NOZZLE_TIMEOUT)
  121. #error "FILAMENT_CHANGE_NOZZLE_TIMEOUT is now PAUSE_PARK_NOZZLE_TIMEOUT. Please update your configuration."
  122. #elif ENABLED(FILAMENT_CHANGE_NO_STEPPER_TIMEOUT)
  123. #error "FILAMENT_CHANGE_NO_STEPPER_TIMEOUT is now PAUSE_PARK_NO_STEPPER_TIMEOUT. Please update your configuration."
  124. #elif defined(PLA_PREHEAT_HOTEND_TEMP)
  125. #error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
  126. #elif defined(PLA_PREHEAT_HPB_TEMP)
  127. #error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
  128. #elif defined(PLA_PREHEAT_FAN_SPEED)
  129. #error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
  130. #elif defined(ABS_PREHEAT_HOTEND_TEMP)
  131. #error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
  132. #elif defined(ABS_PREHEAT_HPB_TEMP)
  133. #error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
  134. #elif defined(ABS_PREHEAT_FAN_SPEED)
  135. #error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
  136. #elif defined(ENDSTOPS_ONLY_FOR_HOMING)
  137. #error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead."
  138. #elif defined(HOMING_FEEDRATE)
  139. #error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead."
  140. #elif defined(MANUAL_HOME_POSITIONS)
  141. #error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead."
  142. #elif defined(PID_ADD_EXTRUSION_RATE)
  143. #error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration."
  144. #elif defined(Z_RAISE_BEFORE_HOMING)
  145. #error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
  146. #elif defined(MIN_Z_HEIGHT_FOR_HOMING)
  147. #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
  148. #elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
  149. #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE instead."
  150. #elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
  151. #error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
  152. #elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT)
  153. #error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
  154. #elif defined(MANUAL_BED_LEVELING)
  155. #error "MANUAL_BED_LEVELING is now LCD_BED_LEVELING. Please update your configuration."
  156. #elif defined(MESH_HOME_SEARCH_Z)
  157. #error "MESH_HOME_SEARCH_Z is now LCD_PROBE_Z_RANGE. Please update your configuration."
  158. #elif defined(MANUAL_PROBE_Z_RANGE)
  159. #error "MANUAL_PROBE_Z_RANGE is now LCD_PROBE_Z_RANGE. Please update your configuration."
  160. #elif !defined(MIN_STEPS_PER_SEGMENT)
  161. #error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
  162. #elif defined(PREVENT_DANGEROUS_EXTRUDE)
  163. #error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration."
  164. #elif defined(SCARA)
  165. #error "SCARA is now MORGAN_SCARA. Please update your configuration."
  166. #elif defined(ENABLE_AUTO_BED_LEVELING)
  167. #error "ENABLE_AUTO_BED_LEVELING is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
  168. #elif defined(AUTO_BED_LEVELING_FEATURE)
  169. #error "AUTO_BED_LEVELING_FEATURE is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
  170. #elif defined(ABL_GRID_POINTS)
  171. #error "ABL_GRID_POINTS is now GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y. Please update your configuration."
  172. #elif defined(ABL_GRID_POINTS_X) || defined(ABL_GRID_POINTS_Y)
  173. #error "ABL_GRID_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration."
  174. #elif defined(ABL_GRID_MAX_POINTS_X) || defined(ABL_GRID_MAX_POINTS_Y)
  175. #error "ABL_GRID_MAX_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration."
  176. #elif defined(MESH_NUM_X_POINTS) || defined(MESH_NUM_Y_POINTS)
  177. #error "MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration."
  178. #elif defined(UBL_MESH_NUM_X_POINTS) || defined(UBL_MESH_NUM_Y_POINTS)
  179. #error "UBL_MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration."
  180. #elif defined(UBL_MESH_EDIT_ENABLED)
  181. #error "UBL_MESH_EDIT_ENABLED is now UBL_G26_MESH_VALIDATION. Please update your configuration."
  182. #elif defined(UBL_MESH_EDITING)
  183. #error "UBL_MESH_EDITING is now UBL_G26_MESH_VALIDATION. Please update your configuration."
  184. #elif defined(BLTOUCH_HEATERS_OFF)
  185. #error "BLTOUCH_HEATERS_OFF is now PROBING_HEATERS_OFF. Please update your configuration."
  186. #elif defined(BEEPER)
  187. #error "BEEPER is now BEEPER_PIN. Please update your pins definitions."
  188. #elif defined(SDCARDDETECT)
  189. #error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions."
  190. #elif defined(STAT_LED_RED) || defined(STAT_LED_BLUE)
  191. #error "STAT_LED_RED/STAT_LED_BLUE are now STAT_LED_RED_PIN/STAT_LED_BLUE_PIN. Please update your pins definitions."
  192. #elif defined(LCD_PIN_BL)
  193. #error "LCD_PIN_BL is now LCD_BACKLIGHT_PIN. Please update your pins definitions."
  194. #elif defined(LCD_PIN_RESET)
  195. #error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions."
  196. #elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN)
  197. #error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h."
  198. #elif defined(min_software_endstops) || defined(max_software_endstops)
  199. #error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS. Please update your configuration."
  200. #elif ENABLED(Z_PROBE_SLED) && defined(SLED_PIN)
  201. #error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)."
  202. #elif defined(CONTROLLERFAN_PIN)
  203. #error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h."
  204. #elif defined(MIN_RETRACT)
  205. #error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
  206. #endif
  207. /**
  208. * Marlin release, version and default string
  209. */
  210. #ifndef SHORT_BUILD_VERSION
  211. #error "SHORT_BUILD_VERSION must be specified."
  212. #elif !defined(DETAILED_BUILD_VERSION)
  213. #error "BUILD_VERSION must be specified."
  214. #elif !defined(STRING_DISTRIBUTION_DATE)
  215. #error "STRING_DISTRIBUTION_DATE must be specified."
  216. #elif !defined(PROTOCOL_VERSION)
  217. #error "PROTOCOL_VERSION must be specified."
  218. #elif !defined(MACHINE_NAME)
  219. #error "MACHINE_NAME must be specified."
  220. #elif !defined(SOURCE_CODE_URL)
  221. #error "SOURCE_CODE_URL must be specified."
  222. #elif !defined(DEFAULT_MACHINE_UUID)
  223. #error "DEFAULT_MACHINE_UUID must be specified."
  224. #elif !defined(WEBSITE_URL)
  225. #error "WEBSITE_URL must be specified."
  226. #endif
  227. /**
  228. * Dual Stepper Drivers
  229. */
  230. #if ENABLED(X_DUAL_STEPPER_DRIVERS) && ENABLED(DUAL_X_CARRIAGE)
  231. #error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS."
  232. #elif ENABLED(X_DUAL_STEPPER_DRIVERS) && (!HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR)
  233. #error "X_DUAL_STEPPER_DRIVERS requires X2 pins (and an extra E plug)."
  234. #elif ENABLED(Y_DUAL_STEPPER_DRIVERS) && (!HAS_Y2_ENABLE || !HAS_Y2_STEP || !HAS_Y2_DIR)
  235. #error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins (and an extra E plug)."
  236. #elif ENABLED(Z_DUAL_STEPPER_DRIVERS) && (!HAS_Z2_ENABLE || !HAS_Z2_STEP || !HAS_Z2_DIR)
  237. #error "Z_DUAL_STEPPER_DRIVERS requires Z2 pins (and an extra E plug)."
  238. #endif
  239. /**
  240. * Validate that the bed size fits
  241. */
  242. static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE,
  243. "Movement bounds ([XY]_MIN_POS, [XY]_MAX_POS) are too narrow to contain [XY]_BED_SIZE.");
  244. /**
  245. * Progress Bar
  246. */
  247. #if ENABLED(LCD_PROGRESS_BAR)
  248. #if DISABLED(SDSUPPORT)
  249. #error "LCD_PROGRESS_BAR requires SDSUPPORT."
  250. #elif ENABLED(DOGLCD)
  251. #error "LCD_PROGRESS_BAR does not apply to graphical displays."
  252. #elif ENABLED(FILAMENT_LCD_DISPLAY)
  253. #error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
  254. #endif
  255. #endif
  256. /**
  257. * SD File Sorting
  258. */
  259. #if ENABLED(SDCARD_SORT_ALPHA)
  260. #if SDSORT_LIMIT > 256
  261. #error "SDSORT_LIMIT must be 256 or smaller."
  262. #elif SDSORT_LIMIT < 10
  263. #error "SDSORT_LIMIT should be greater than 9 to be useful."
  264. #elif DISABLED(SDSORT_USES_RAM)
  265. #if ENABLED(SDSORT_DYNAMIC_RAM)
  266. #error "SDSORT_DYNAMIC_RAM requires SDSORT_USES_RAM (which reads the directory into RAM)."
  267. #elif ENABLED(SDSORT_CACHE_NAMES)
  268. #error "SDSORT_CACHE_NAMES requires SDSORT_USES_RAM (which reads the directory into RAM)."
  269. #endif
  270. #endif
  271. #endif
  272. /**
  273. * I2C Position Encoders
  274. */
  275. #if ENABLED(I2C_POSITION_ENCODERS)
  276. #if DISABLED(BABYSTEPPING)
  277. #error "I2C_POSITION_ENCODERS requires BABYSTEPPING."
  278. #elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5)
  279. #error "I2CPE_ENCODER_CNT must be between 1 and 5."
  280. #endif
  281. #endif
  282. /**
  283. * Babystepping
  284. */
  285. #if ENABLED(BABYSTEPPING)
  286. #if DISABLED(ULTRA_LCD) && DISABLED(I2C_POSITION_ENCODERS)
  287. #error "BABYSTEPPING requires an LCD controller."
  288. #elif ENABLED(SCARA)
  289. #error "BABYSTEPPING is not implemented for SCARA yet."
  290. #elif ENABLED(DELTA) && ENABLED(BABYSTEP_XY)
  291. #error "BABYSTEPPING only implemented for Z axis on deltabots."
  292. #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && ENABLED(MESH_BED_LEVELING)
  293. #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
  294. #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE
  295. #error "BABYSTEP_ZPROBE_OFFSET requires a probe."
  296. #endif
  297. #endif
  298. /**
  299. * Filament Runout needs a pin and either SD Support or Auto print start detection
  300. */
  301. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  302. #if !HAS_FIL_RUNOUT
  303. #error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
  304. #elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
  305. #error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
  306. #elif DISABLED(ADVANCED_PAUSE_FEATURE)
  307. static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
  308. #endif
  309. #endif
  310. /**
  311. * Advanced Pause
  312. */
  313. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  314. #if DISABLED(NEWPANEL)
  315. #error "ADVANCED_PAUSE_FEATURE currently requires an LCD controller."
  316. #elif ENABLED(EXTRUDER_RUNOUT_PREVENT)
  317. #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
  318. #elif ENABLED(PARK_HEAD_ON_PAUSE) && DISABLED(SDSUPPORT) && DISABLED(NEWPANEL) && DISABLED(EMERGENCY_PARSER)
  319. #error "PARK_HEAD_ON_PAUSE requires SDSUPPORT, EMERGENCY_PARSER, or an LCD controller."
  320. #elif ENABLED(HOME_BEFORE_FILAMENT_CHANGE) && DISABLED(PAUSE_PARK_NO_STEPPER_TIMEOUT)
  321. #error "HOME_BEFORE_FILAMENT_CHANGE requires PAUSE_PARK_NO_STEPPER_TIMEOUT"
  322. #endif
  323. #endif
  324. /**
  325. * Individual axis homing is useless for DELTAS
  326. */
  327. #if ENABLED(INDIVIDUAL_AXIS_HOMING_MENU) && ENABLED(DELTA)
  328. #error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics."
  329. #endif
  330. /**
  331. * Options only for EXTRUDERS > 1
  332. */
  333. #if EXTRUDERS > 1
  334. #if EXTRUDERS > 5
  335. #error "Marlin supports a maximum of 5 EXTRUDERS."
  336. #endif
  337. #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
  338. #error "EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT."
  339. #endif
  340. #if ENABLED(HEATERS_PARALLEL)
  341. #error "EXTRUDERS must be 1 with HEATERS_PARALLEL."
  342. #endif
  343. #elif ENABLED(MK2_MULTIPLEXER)
  344. #error "MK2_MULTIPLEXER requires 2 or more EXTRUDERS."
  345. #elif ENABLED(SINGLENOZZLE)
  346. #error "SINGLENOZZLE requires 2 or more EXTRUDERS."
  347. #endif
  348. /**
  349. * Sanity checking for the Průša MK2 Multiplexer
  350. */
  351. #ifdef SNMM
  352. #error "SNMM is now MK2_MULTIPLEXER. Please update your configuration."
  353. #elif ENABLED(MK2_MULTIPLEXER) && DISABLED(ADVANCED_PAUSE_FEATURE)
  354. #error "ADVANCED_PAUSE_FEATURE is required with MK2_MULTIPLEXER."
  355. #endif
  356. /**
  357. * A Dual Nozzle carriage with switching servo
  358. */
  359. #if ENABLED(SWITCHING_NOZZLE)
  360. #if ENABLED(DUAL_X_CARRIAGE)
  361. #error "SWITCHING_NOZZLE and DUAL_X_CARRIAGE are incompatible."
  362. #elif ENABLED(SINGLENOZZLE)
  363. #error "SWITCHING_NOZZLE and SINGLENOZZLE are incompatible."
  364. #elif EXTRUDERS != 2
  365. #error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS."
  366. #elif NUM_SERVOS < 1
  367. #error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1."
  368. #endif
  369. #endif
  370. /**
  371. * Single Stepper Dual Extruder with switching servo
  372. */
  373. #if ENABLED(SWITCHING_EXTRUDER) && NUM_SERVOS < 1
  374. #error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1."
  375. #endif
  376. /**
  377. * Mixing Extruder requirements
  378. */
  379. #if ENABLED(MIXING_EXTRUDER)
  380. #if EXTRUDERS > 1
  381. #error "MIXING_EXTRUDER currently only supports one extruder."
  382. #elif MIXING_STEPPERS < 2
  383. #error "You must set MIXING_STEPPERS >= 2 for a mixing extruder."
  384. #elif ENABLED(FILAMENT_SENSOR)
  385. #error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway."
  386. #elif ENABLED(SWITCHING_EXTRUDER)
  387. #error "Please select either MIXING_EXTRUDER or SWITCHING_EXTRUDER, not both."
  388. #elif ENABLED(SINGLENOZZLE)
  389. #error "MIXING_EXTRUDER is incompatible with SINGLENOZZLE."
  390. #elif ENABLED(LIN_ADVANCE)
  391. #error "MIXING_EXTRUDER is incompatible with LIN_ADVANCE."
  392. #endif
  393. #endif
  394. /**
  395. * Limited number of servos
  396. */
  397. #if NUM_SERVOS > 4
  398. #error "The maximum number of SERVOS in Marlin is 4."
  399. #endif
  400. /**
  401. * Servo deactivation depends on servo endstops, switching nozzle, or switching extruder
  402. */
  403. #if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_ENDSTOP && !defined(SWITCHING_NOZZLE_SERVO_NR) && !defined(SWITCHING_EXTRUDER_SERVO_NR)
  404. #error "Z_ENDSTOP_SERVO_NR, switching nozzle, or switching extruder is required for DEACTIVATE_SERVOS_AFTER_MOVE."
  405. #endif
  406. /**
  407. * Required LCD language
  408. */
  409. #if DISABLED(DOGLCD) && ENABLED(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780)
  410. #error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller."
  411. #endif
  412. /**
  413. * Bed Heating Options - PID vs Limit Switching
  414. */
  415. #if ENABLED(PIDTEMPBED) && ENABLED(BED_LIMIT_SWITCHING)
  416. #error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED."
  417. #endif
  418. /**
  419. * Kinematics
  420. */
  421. /**
  422. * Allow only one kinematic type to be defined
  423. */
  424. static_assert(1 >= 0
  425. #if ENABLED(DELTA)
  426. + 1
  427. #endif
  428. #if ENABLED(MORGAN_SCARA)
  429. + 1
  430. #endif
  431. #if ENABLED(MAKERARM_SCARA)
  432. + 1
  433. #endif
  434. #if ENABLED(COREXY)
  435. + 1
  436. #endif
  437. #if ENABLED(COREXZ)
  438. + 1
  439. #endif
  440. #if ENABLED(COREYZ)
  441. + 1
  442. #endif
  443. #if ENABLED(COREYX)
  444. + 1
  445. #endif
  446. #if ENABLED(COREZX)
  447. + 1
  448. #endif
  449. #if ENABLED(COREZY)
  450. + 1
  451. #endif
  452. , "Please enable only one of DELTA, MORGAN_SCARA, MAKERARM_SCARA, COREXY, COREYX, COREXZ, COREZX, COREYZ, or COREZY."
  453. );
  454. /**
  455. * Delta requirements
  456. */
  457. #if ENABLED(DELTA)
  458. #if DISABLED(USE_XMAX_PLUG) && DISABLED(USE_YMAX_PLUG) && DISABLED(USE_ZMAX_PLUG)
  459. #error "You probably want to use Max Endstops for DELTA!"
  460. #elif ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(AUTO_BED_LEVELING_BILINEAR) && !UBL_DELTA
  461. #error "ENABLE_LEVELING_FADE_HEIGHT on DELTA requires AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
  462. #elif ENABLED(DELTA_AUTO_CALIBRATION) && !PROBE_SELECTED
  463. #error "DELTA_AUTO_CALIBRATION requires a probe: PROBE_MANUALLY, FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, Z Servo."
  464. #elif ENABLED(DELTA_AUTO_CALIBRATION) && ENABLED(PROBE_MANUALLY) && DISABLED(ULTIPANEL)
  465. #error "DELTA_AUTO_CALIBRATION requires an LCD controller with PROBE_MANUALLY."
  466. #elif ABL_GRID
  467. #if (GRID_MAX_POINTS_X & 1) == 0 || (GRID_MAX_POINTS_Y & 1) == 0
  468. #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be odd numbers."
  469. #elif GRID_MAX_POINTS_X < 3
  470. #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be 3 or higher."
  471. #endif
  472. #endif
  473. #endif
  474. /**
  475. * Probes
  476. */
  477. /**
  478. * Allow only one probe option to be defined
  479. */
  480. static_assert(1 >= 0
  481. #if ENABLED(PROBE_MANUALLY)
  482. + 1
  483. #endif
  484. #if ENABLED(FIX_MOUNTED_PROBE)
  485. + 1
  486. #endif
  487. #if HAS_Z_SERVO_ENDSTOP && DISABLED(BLTOUCH)
  488. + 1
  489. #endif
  490. #if ENABLED(BLTOUCH)
  491. + 1
  492. #endif
  493. #if ENABLED(SOLENOID_PROBE)
  494. + 1
  495. #endif
  496. #if ENABLED(Z_PROBE_ALLEN_KEY)
  497. + 1
  498. #endif
  499. #if ENABLED(Z_PROBE_SLED)
  500. + 1
  501. #endif
  502. , "Please enable only one probe option: PROBE_MANUALLY, FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo."
  503. );
  504. #if PROBE_SELECTED
  505. /**
  506. * Z_PROBE_SLED is incompatible with DELTA
  507. */
  508. #if ENABLED(Z_PROBE_SLED) && ENABLED(DELTA)
  509. #error "You cannot use Z_PROBE_SLED with DELTA."
  510. #endif
  511. /**
  512. * SOLENOID_PROBE requirements
  513. */
  514. #if ENABLED(SOLENOID_PROBE)
  515. #if ENABLED(EXT_SOLENOID)
  516. #error "SOLENOID_PROBE is incompatible with EXT_SOLENOID."
  517. #elif !HAS_SOLENOID_1
  518. #error "SOLENOID_PROBE requires SOL1_PIN. It can be added to your Configuration.h."
  519. #endif
  520. #endif
  521. /**
  522. * NUM_SERVOS is required for a Z servo probe
  523. */
  524. #if HAS_Z_SERVO_ENDSTOP
  525. #ifndef NUM_SERVOS
  526. #error "You must set NUM_SERVOS for a Z servo probe (Z_ENDSTOP_SERVO_NR)."
  527. #elif Z_ENDSTOP_SERVO_NR >= NUM_SERVOS
  528. #error "Z_ENDSTOP_SERVO_NR must be smaller than NUM_SERVOS."
  529. #endif
  530. #endif
  531. /**
  532. * Require pin options and pins to be defined
  533. */
  534. #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
  535. #if ENABLED(Z_MIN_PROBE_ENDSTOP)
  536. #error "Enable only one option: Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN."
  537. #elif DISABLED(USE_ZMIN_PLUG)
  538. #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled."
  539. #elif !HAS_Z_MIN
  540. #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined."
  541. #elif ENABLED(Z_MIN_PROBE_ENDSTOP_INVERTING) != ENABLED(Z_MIN_ENDSTOP_INVERTING)
  542. #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match Z_MIN_PROBE_ENDSTOP_INVERTING."
  543. #endif
  544. #elif ENABLED(Z_MIN_PROBE_ENDSTOP)
  545. #if !HAS_Z_MIN_PROBE_PIN
  546. #error "Z_MIN_PROBE_ENDSTOP requires the Z_MIN_PROBE_PIN to be defined."
  547. #endif
  548. #elif DISABLED(PROBE_MANUALLY)
  549. #error "You must enable either Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use a probe."
  550. #endif
  551. /**
  552. * Make sure Z raise values are set
  553. */
  554. #if !defined(Z_CLEARANCE_DEPLOY_PROBE)
  555. #error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration."
  556. #elif !defined(Z_CLEARANCE_BETWEEN_PROBES)
  557. #error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration."
  558. #elif Z_CLEARANCE_DEPLOY_PROBE < 0
  559. #error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0."
  560. #elif Z_CLEARANCE_BETWEEN_PROBES < 0
  561. #error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0."
  562. #endif
  563. #else
  564. /**
  565. * Require some kind of probe for bed leveling and probe testing
  566. */
  567. #if HAS_ABL
  568. #if ENABLED(AUTO_BED_LEVELING_UBL)
  569. #error "Unified Bed Leveling requires a probe: FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo."
  570. #else
  571. #error "Auto Bed Leveling requires one of these: PROBE_MANUALLY, FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or a Z Servo."
  572. #endif
  573. #endif
  574. #endif
  575. #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST) && !HAS_BED_PROBE
  576. #error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe: FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo."
  577. #endif
  578. /**
  579. * Allow only one bed leveling option to be defined
  580. */
  581. static_assert(1 >= 0
  582. #if ENABLED(AUTO_BED_LEVELING_LINEAR)
  583. + 1
  584. #endif
  585. #if ENABLED(AUTO_BED_LEVELING_3POINT)
  586. + 1
  587. #endif
  588. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  589. + 1
  590. #endif
  591. #if ENABLED(AUTO_BED_LEVELING_UBL)
  592. + 1
  593. #endif
  594. #if ENABLED(MESH_BED_LEVELING)
  595. + 1
  596. #endif
  597. , "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
  598. );
  599. /**
  600. * Bed Leveling Requirements
  601. */
  602. #if ENABLED(AUTO_BED_LEVELING_UBL)
  603. /**
  604. * Unified Bed Leveling
  605. */
  606. #if IS_SCARA
  607. #error "AUTO_BED_LEVELING_UBL does not yet support SCARA printers."
  608. #elif DISABLED(EEPROM_SETTINGS)
  609. #error "AUTO_BED_LEVELING_UBL requires EEPROM_SETTINGS. Please update your configuration."
  610. #elif !WITHIN(GRID_MAX_POINTS_X, 3, 15) || !WITHIN(GRID_MAX_POINTS_Y, 3, 15)
  611. #error "GRID_MAX_POINTS_[XY] must be a whole number between 3 and 15."
  612. #else
  613. static_assert(WITHIN(UBL_PROBE_PT_1_X, MIN_PROBE_X, MAX_PROBE_X), "UBL_PROBE_PT_1_X can't be reached by the Z probe.");
  614. static_assert(WITHIN(UBL_PROBE_PT_2_X, MIN_PROBE_X, MAX_PROBE_X), "UBL_PROBE_PT_2_X can't be reached by the Z probe.");
  615. static_assert(WITHIN(UBL_PROBE_PT_3_X, MIN_PROBE_X, MAX_PROBE_X), "UBL_PROBE_PT_3_X can't be reached by the Z probe.");
  616. static_assert(WITHIN(UBL_PROBE_PT_1_Y, MIN_PROBE_Y, MAX_PROBE_Y), "UBL_PROBE_PT_1_Y can't be reached by the Z probe.");
  617. static_assert(WITHIN(UBL_PROBE_PT_2_Y, MIN_PROBE_Y, MAX_PROBE_Y), "UBL_PROBE_PT_2_Y can't be reached by the Z probe.");
  618. static_assert(WITHIN(UBL_PROBE_PT_3_Y, MIN_PROBE_Y, MAX_PROBE_Y), "UBL_PROBE_PT_3_Y can't be reached by the Z probe.");
  619. #endif
  620. #elif HAS_ABL
  621. /**
  622. * Auto Bed Leveling
  623. */
  624. #if ENABLED(USE_RAW_KINEMATICS)
  625. #error "USE_RAW_KINEMATICS is not compatible with AUTO_BED_LEVELING"
  626. #endif
  627. /**
  628. * Delta and SCARA have limited bed leveling options
  629. */
  630. #if IS_SCARA && DISABLED(AUTO_BED_LEVELING_BILINEAR)
  631. #error "Only AUTO_BED_LEVELING_BILINEAR currently supports SCARA bed leveling."
  632. #endif
  633. /**
  634. * Check auto bed leveling probe points
  635. */
  636. #if ABL_GRID
  637. #ifdef DELTA_PROBEABLE_RADIUS
  638. static_assert(LEFT_PROBE_BED_POSITION >= -DELTA_PROBEABLE_RADIUS, "LEFT_PROBE_BED_POSITION must be within DELTA_PROBEABLE_RADIUS.");
  639. static_assert(RIGHT_PROBE_BED_POSITION <= DELTA_PROBEABLE_RADIUS, "RIGHT_PROBE_BED_POSITION must be within DELTA_PROBEABLE_RADIUS.");
  640. static_assert(FRONT_PROBE_BED_POSITION >= -DELTA_PROBEABLE_RADIUS, "FRONT_PROBE_BED_POSITION must be within DELTA_PROBEABLE_RADIUS.");
  641. static_assert(BACK_PROBE_BED_POSITION <= DELTA_PROBEABLE_RADIUS, "BACK_PROBE_BED_POSITION must be within DELTA_PROBEABLE_RADIUS.");
  642. #else
  643. static_assert(LEFT_PROBE_BED_POSITION < RIGHT_PROBE_BED_POSITION, "LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION.");
  644. static_assert(FRONT_PROBE_BED_POSITION < BACK_PROBE_BED_POSITION, "FRONT_PROBE_BED_POSITION must be less than BACK_PROBE_BED_POSITION.");
  645. static_assert(LEFT_PROBE_BED_POSITION >= MIN_PROBE_X, "LEFT_PROBE_BED_POSITION can't be reached by the Z probe.");
  646. static_assert(RIGHT_PROBE_BED_POSITION <= MAX_PROBE_X, "RIGHT_PROBE_BED_POSITION can't be reached by the Z probe.");
  647. static_assert(FRONT_PROBE_BED_POSITION >= MIN_PROBE_Y, "FRONT_PROBE_BED_POSITION can't be reached by the Z probe.");
  648. static_assert(BACK_PROBE_BED_POSITION <= MAX_PROBE_Y, "BACK_PROBE_BED_POSITION can't be reached by the Z probe.");
  649. #endif
  650. #else // AUTO_BED_LEVELING_3POINT
  651. static_assert(WITHIN(ABL_PROBE_PT_1_X, MIN_PROBE_X, MAX_PROBE_X), "ABL_PROBE_PT_1_X can't be reached by the Z probe.");
  652. static_assert(WITHIN(ABL_PROBE_PT_2_X, MIN_PROBE_X, MAX_PROBE_X), "ABL_PROBE_PT_2_X can't be reached by the Z probe.");
  653. static_assert(WITHIN(ABL_PROBE_PT_3_X, MIN_PROBE_X, MAX_PROBE_X), "ABL_PROBE_PT_3_X can't be reached by the Z probe.");
  654. static_assert(WITHIN(ABL_PROBE_PT_1_Y, MIN_PROBE_Y, MAX_PROBE_Y), "ABL_PROBE_PT_1_Y can't be reached by the Z probe.");
  655. static_assert(WITHIN(ABL_PROBE_PT_2_Y, MIN_PROBE_Y, MAX_PROBE_Y), "ABL_PROBE_PT_2_Y can't be reached by the Z probe.");
  656. static_assert(WITHIN(ABL_PROBE_PT_3_Y, MIN_PROBE_Y, MAX_PROBE_Y), "ABL_PROBE_PT_3_Y can't be reached by the Z probe.");
  657. #endif // AUTO_BED_LEVELING_3POINT
  658. #elif ENABLED(MESH_BED_LEVELING)
  659. /**
  660. * Mesh Bed Leveling
  661. */
  662. #if ENABLED(DELTA)
  663. #error "MESH_BED_LEVELING does not yet support DELTA printers."
  664. #elif GRID_MAX_POINTS_X > 9 || GRID_MAX_POINTS_Y > 9
  665. #error "GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y must be less than 10 for MBL."
  666. #endif
  667. #endif
  668. /**
  669. * LCD_BED_LEVELING requirements
  670. */
  671. #if ENABLED(LCD_BED_LEVELING)
  672. #if DISABLED(ULTIPANEL)
  673. #error "LCD_BED_LEVELING requires an LCD controller."
  674. #elif DISABLED(MESH_BED_LEVELING) && !(HAS_ABL && ENABLED(PROBE_MANUALLY))
  675. #error "LCD_BED_LEVELING requires MESH_BED_LEVELING or PROBE_MANUALLY with auto bed leveling enabled."
  676. #endif
  677. #endif
  678. /**
  679. * Homing Bump
  680. */
  681. #if X_HOME_BUMP_MM < 0 || Y_HOME_BUMP_MM < 0 || Z_HOME_BUMP_MM < 0
  682. #error "[XYZ]_HOME_BUMP_MM must be greater than or equal to 0."
  683. #endif
  684. /**
  685. * Make sure Z_SAFE_HOMING point is reachable
  686. */
  687. #if ENABLED(Z_SAFE_HOMING)
  688. #if !WITHIN(Z_SAFE_HOMING_X_POINT, MIN_PROBE_X, MAX_PROBE_X)
  689. #if HAS_BED_PROBE
  690. #error "Z_SAFE_HOMING_X_POINT can't be reached by the Z probe."
  691. #else
  692. #error "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle."
  693. #endif
  694. #elif !WITHIN(Z_SAFE_HOMING_Y_POINT, MIN_PROBE_Y, MAX_PROBE_Y)
  695. #if HAS_BED_PROBE
  696. #error "Z_SAFE_HOMING_Y_POINT can't be reached by the Z probe."
  697. #else
  698. #error "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle."
  699. #endif
  700. #endif
  701. #endif // Z_SAFE_HOMING
  702. /**
  703. * Make sure DISABLE_[XYZ] compatible with selected homing options
  704. */
  705. #if ENABLED(DISABLE_X) || ENABLED(DISABLE_Y) || ENABLED(DISABLE_Z)
  706. #if ENABLED(HOME_AFTER_DEACTIVATE) || ENABLED(Z_SAFE_HOMING)
  707. #error "DISABLE_[XYZ] not compatible with HOME_AFTER_DEACTIVATE or Z_SAFE_HOMING."
  708. #endif
  709. #endif // DISABLE_[XYZ]
  710. /**
  711. * Advance Extrusion
  712. */
  713. #if ENABLED(ADVANCE) && ENABLED(LIN_ADVANCE)
  714. #error "You can enable ADVANCE or LIN_ADVANCE, but not both."
  715. #endif
  716. /**
  717. * Filament Width Sensor
  718. */
  719. #if ENABLED(FILAMENT_WIDTH_SENSOR) && !HAS_FILAMENT_WIDTH_SENSOR
  720. #error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined."
  721. #endif
  722. /**
  723. * ULTIPANEL encoder
  724. */
  725. #if ENABLED(ULTIPANEL) && DISABLED(NEWPANEL) && DISABLED(SR_LCD_2W_NL) && !defined(SHIFT_CLK)
  726. #error "ULTIPANEL requires some kind of encoder."
  727. #endif
  728. #if ENCODER_PULSES_PER_STEP < 0
  729. #error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead."
  730. #endif
  731. /**
  732. * SAV_3DGLCD display options
  733. */
  734. #if ENABLED(U8GLIB_SSD1306) && ENABLED(U8GLIB_SH1106)
  735. #error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
  736. #endif
  737. /**
  738. * Allen Key
  739. * Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis.
  740. */
  741. #if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
  742. #error "You can't home to a z min endstop with a Z_PROBE_ALLEN_KEY"
  743. #endif
  744. /**
  745. * Dual X Carriage requirements
  746. */
  747. #if ENABLED(DUAL_X_CARRIAGE)
  748. #if EXTRUDERS == 1
  749. #error "DUAL_X_CARRIAGE requires 2 (or more) extruders."
  750. #elif CORE_IS_XY || CORE_IS_XZ
  751. #error "DUAL_X_CARRIAGE cannot be used with COREXY, COREYX, COREXZ, or COREZX."
  752. #elif !HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR
  753. #error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined."
  754. #elif !HAS_X_MAX
  755. #error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop."
  756. #elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS)
  757. #error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS."
  758. #elif X_HOME_DIR != -1 || X2_HOME_DIR != 1
  759. #error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1."
  760. #endif
  761. #endif // DUAL_X_CARRIAGE
  762. /**
  763. * Make sure auto fan pins don't conflict with the fan pin
  764. */
  765. #if HAS_AUTO_FAN
  766. #if HAS_FAN0
  767. #if E0_AUTO_FAN_PIN == FAN_PIN
  768. #error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN."
  769. #elif E1_AUTO_FAN_PIN == FAN_PIN
  770. #error "You cannot set E1_AUTO_FAN_PIN equal to FAN_PIN."
  771. #elif E2_AUTO_FAN_PIN == FAN_PIN
  772. #error "You cannot set E2_AUTO_FAN_PIN equal to FAN_PIN."
  773. #elif E3_AUTO_FAN_PIN == FAN_PIN
  774. #error "You cannot set E3_AUTO_FAN_PIN equal to FAN_PIN."
  775. #endif
  776. #endif
  777. #endif
  778. #if HAS_FAN0 && CONTROLLER_FAN_PIN == FAN_PIN
  779. #error "You cannot set CONTROLLER_FAN_PIN equal to FAN_PIN."
  780. #endif
  781. #if ENABLED(USE_CONTROLLER_FAN)
  782. #if !HAS_CONTROLLER_FAN
  783. #error "USE_CONTROLLER_FAN requires a CONTROLLER_FAN_PIN. Define in Configuration_adv.h."
  784. #elif E0_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
  785. #error "You cannot set E0_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
  786. #elif E1_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
  787. #error "You cannot set E1_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
  788. #elif E2_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
  789. #error "You cannot set E2_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
  790. #elif E3_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
  791. #error "You cannot set E3_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
  792. #endif
  793. #endif
  794. /**
  795. * Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set.
  796. */
  797. #if !HAS_HEATER_0
  798. #error "HEATER_0_PIN not defined for this board."
  799. #elif !PIN_EXISTS(TEMP_0) && !(defined(MAX6675_SS) && MAX6675_SS >= 0)
  800. #error "TEMP_0_PIN not defined for this board."
  801. #elif !PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE)
  802. #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
  803. #elif TEMP_SENSOR_0 == 0
  804. #error "TEMP_SENSOR_0 is required."
  805. #endif
  806. #if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)
  807. #if !HAS_HEATER_1
  808. #error "HEATER_1_PIN not defined for this board."
  809. #endif
  810. #endif
  811. #if HOTENDS > 1
  812. #if TEMP_SENSOR_1 == 0
  813. #error "TEMP_SENSOR_1 is required with 2 or more HOTENDS."
  814. #elif !PIN_EXISTS(TEMP_1)
  815. #error "TEMP_1_PIN not defined for this board."
  816. #endif
  817. #if HOTENDS > 2
  818. #if TEMP_SENSOR_2 == 0
  819. #error "TEMP_SENSOR_2 is required with 3 or more HOTENDS."
  820. #elif !HAS_HEATER_2
  821. #error "HEATER_2_PIN not defined for this board."
  822. #elif !PIN_EXISTS(TEMP_2)
  823. #error "TEMP_2_PIN not defined for this board."
  824. #endif
  825. #if HOTENDS > 3
  826. #if TEMP_SENSOR_3 == 0
  827. #error "TEMP_SENSOR_3 is required with 4 or more HOTENDS."
  828. #elif !HAS_HEATER_3
  829. #error "HEATER_3_PIN not defined for this board."
  830. #elif !PIN_EXISTS(TEMP_3)
  831. #error "TEMP_3_PIN not defined for this board."
  832. #endif
  833. #if HOTENDS > 4
  834. #if TEMP_SENSOR_4 == 0
  835. #error "TEMP_SENSOR_4 is required with 5 HOTENDS."
  836. #elif !HAS_HEATER_4
  837. #error "HEATER_4_PIN not defined for this board."
  838. #elif !PIN_EXISTS(TEMP_4)
  839. #error "TEMP_4_PIN not defined for this board."
  840. #endif
  841. #elif TEMP_SENSOR_4 != 0
  842. #error "TEMP_SENSOR_4 shouldn't be set with only 4 extruders."
  843. #endif
  844. #elif TEMP_SENSOR_3 != 0
  845. #error "TEMP_SENSOR_3 shouldn't be set with only 3 extruders."
  846. #elif TEMP_SENSOR_4 != 0
  847. #error "TEMP_SENSOR_4 shouldn't be set with only 3 extruders."
  848. #endif
  849. #elif TEMP_SENSOR_2 != 0
  850. #error "TEMP_SENSOR_2 shouldn't be set with only 2 extruders."
  851. #elif TEMP_SENSOR_3 != 0
  852. #error "TEMP_SENSOR_3 shouldn't be set with only 2 extruders."
  853. #elif TEMP_SENSOR_4 != 0
  854. #error "TEMP_SENSOR_4 shouldn't be set with only 2 extruders."
  855. #endif
  856. #elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT)
  857. #error "TEMP_SENSOR_1 shouldn't be set with only 1 extruder."
  858. #elif TEMP_SENSOR_2 != 0
  859. #error "TEMP_SENSOR_2 shouldn't be set with only 1 extruder."
  860. #elif TEMP_SENSOR_3 != 0
  861. #error "TEMP_SENSOR_3 shouldn't be set with only 1 extruder."
  862. #elif TEMP_SENSOR_4 != 0
  863. #error "TEMP_SENSOR_4 shouldn't be set with only 1 extruder."
  864. #endif
  865. #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0
  866. #error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT."
  867. #endif
  868. /**
  869. * Temperature status LEDs
  870. */
  871. #if ENABLED(TEMP_STAT_LEDS) && !PIN_EXISTS(STAT_LED_RED) && !PIN_EXISTS(STAT_LED_BLUE)
  872. #error "TEMP_STAT_LEDS requires STAT_LED_RED_PIN or STAT_LED_BLUE_PIN, preferably both."
  873. #endif
  874. /**
  875. * Basic 2-nozzle duplication mode
  876. */
  877. #if ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
  878. #if HOTENDS != 2
  879. #error "DUAL_NOZZLE_DUPLICATION_MODE requires exactly 2 hotends."
  880. #elif ENABLED(DUAL_X_CARRIAGE)
  881. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with DUAL_X_CARRIAGE."
  882. #elif ENABLED(SINGLENOZZLE)
  883. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SINGLENOZZLE."
  884. #elif ENABLED(MIXING_EXTRUDER)
  885. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with MIXING_EXTRUDER."
  886. #elif ENABLED(SWITCHING_EXTRUDER)
  887. #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SWITCHING_EXTRUDER."
  888. #endif
  889. #endif
  890. /**
  891. * Test Extruder Stepper Pins
  892. */
  893. #if E_STEPPERS > 4
  894. #if !PIN_EXISTS(E4_STEP) || !PIN_EXISTS(E4_DIR) || !PIN_EXISTS(E4_ENABLE)
  895. #error "E4_STEP_PIN, E4_DIR_PIN, or E4_ENABLE_PIN not defined for this board."
  896. #endif
  897. #elif E_STEPPERS > 3
  898. #if !PIN_EXISTS(E3_STEP) || !PIN_EXISTS(E3_DIR) || !PIN_EXISTS(E3_ENABLE)
  899. #error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board."
  900. #endif
  901. #elif E_STEPPERS > 2
  902. #if !PIN_EXISTS(E2_STEP) || !PIN_EXISTS(E2_DIR) || !PIN_EXISTS(E2_ENABLE)
  903. #error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board."
  904. #endif
  905. #elif E_STEPPERS > 1
  906. #if !PIN_EXISTS(E1_STEP) || !PIN_EXISTS(E1_DIR) || !PIN_EXISTS(E1_ENABLE)
  907. #error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board."
  908. #endif
  909. #endif
  910. /**
  911. * Endstops
  912. */
  913. #if DISABLED(USE_XMIN_PLUG) && DISABLED(USE_XMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && WITHIN(Z2_USE_ENDSTOP, _XMAX_, _XMIN_))
  914. #error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG."
  915. #elif DISABLED(USE_YMIN_PLUG) && DISABLED(USE_YMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && WITHIN(Z2_USE_ENDSTOP, _YMAX_, _YMIN_))
  916. #error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG."
  917. #elif DISABLED(USE_ZMIN_PLUG) && DISABLED(USE_ZMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && WITHIN(Z2_USE_ENDSTOP, _ZMAX_, _ZMIN_))
  918. #error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG."
  919. #elif ENABLED(Z_DUAL_ENDSTOPS)
  920. #if !Z2_USE_ENDSTOP
  921. #error "You must set Z2_USE_ENDSTOP with Z_DUAL_ENDSTOPS."
  922. #elif Z2_MAX_PIN == 0 && Z2_MIN_PIN == 0
  923. #error "Z2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
  924. #elif ENABLED(DELTA)
  925. #error "Z_DUAL_ENDSTOPS is not compatible with DELTA."
  926. #endif
  927. #elif !IS_SCARA
  928. #if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG)
  929. #error "Enable USE_XMIN_PLUG when homing X to MIN."
  930. #elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG)
  931. #error "Enable USE_XMAX_PLUG when homing X to MAX."
  932. #elif Y_HOME_DIR < 0 && DISABLED(USE_YMIN_PLUG)
  933. #error "Enable USE_YMIN_PLUG when homing Y to MIN."
  934. #elif Y_HOME_DIR > 0 && DISABLED(USE_YMAX_PLUG)
  935. #error "Enable USE_YMAX_PLUG when homing Y to MAX."
  936. #elif Z_HOME_DIR < 0 && DISABLED(USE_ZMIN_PLUG)
  937. #error "Enable USE_ZMIN_PLUG when homing Z to MIN."
  938. #elif Z_HOME_DIR > 0 && DISABLED(USE_ZMAX_PLUG)
  939. #error "Enable USE_ZMAX_PLUG when homing Z to MAX."
  940. #endif
  941. #endif
  942. /**
  943. * emergency-command parser
  944. */
  945. #if ENABLED(EMERGENCY_PARSER) && defined(USBCON)
  946. #error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)."
  947. #endif
  948. /**
  949. * I2C bus
  950. */
  951. #if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0
  952. #if I2C_SLAVE_ADDRESS < 8
  953. #error "I2C_SLAVE_ADDRESS can't be less than 8. (Addresses 0 - 7 are reserved.)"
  954. #elif I2C_SLAVE_ADDRESS > 127
  955. #error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)"
  956. #endif
  957. #endif
  958. /**
  959. * G38 Probe Target
  960. */
  961. #if ENABLED(G38_PROBE_TARGET)
  962. #if !HAS_BED_PROBE
  963. #error "G38_PROBE_TARGET requires a bed probe."
  964. #elif !IS_CARTESIAN
  965. #error "G38_PROBE_TARGET requires a Cartesian machine."
  966. #endif
  967. #endif
  968. /**
  969. * RGB_LED Requirements
  970. */
  971. #define _RGB_TEST (PIN_EXISTS(RGB_LED_R) && PIN_EXISTS(RGB_LED_G) && PIN_EXISTS(RGB_LED_B))
  972. #if ENABLED(RGB_LED)
  973. #if !_RGB_TEST
  974. #error "RGB_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, and RGB_LED_B_PIN."
  975. #elif ENABLED(RGBW_LED)
  976. #error "Please enable only one of RGB_LED and RGBW_LED."
  977. #endif
  978. #elif ENABLED(RGBW_LED)
  979. #if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W))
  980. #error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN."
  981. #endif
  982. #elif ENABLED(NEOPIXEL_RGBW_LED)
  983. #if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0)
  984. #error "NEOPIXEL_RGBW_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
  985. #endif
  986. #elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_RGBW_LED)
  987. #error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_RGBW_LED."
  988. #endif
  989. /**
  990. * Auto Fan check for PWM pins
  991. */
  992. #if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255
  993. #define AF_ERR_SUFF "_AUTO_FAN_PIN is not a PWM pin. Set EXTRUDER_AUTO_FAN_SPEED to 255."
  994. #if HAS_AUTO_FAN_0
  995. static_assert(GET_TIMER(E0_AUTO_FAN_PIN), "E0" AF_ERR_SUFF);
  996. #elif HAS_AUTO_FAN_1
  997. static_assert(GET_TIMER(E1_AUTO_FAN_PIN), "E1" AF_ERR_SUFF);
  998. #elif HAS_AUTO_FAN_2
  999. static_assert(GET_TIMER(E2_AUTO_FAN_PIN), "E2" AF_ERR_SUFF);
  1000. #elif HAS_AUTO_FAN_3
  1001. static_assert(GET_TIMER(E3_AUTO_FAN_PIN), "E3" AF_ERR_SUFF);
  1002. #endif
  1003. #endif
  1004. /**
  1005. * Make sure only one display is enabled
  1006. *
  1007. * Note: BQ_LCD_SMART_CONTROLLER => REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1008. * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER => REPRAP_DISCOUNT_SMART_CONTROLLER
  1009. * SAV_3DGLCD => U8GLIB_SH1106 => ULTIMAKERCONTROLLER
  1010. * miniVIKI => ULTIMAKERCONTROLLER
  1011. * VIKI2 => ULTIMAKERCONTROLLER
  1012. * ELB_FULL_GRAPHIC_CONTROLLER => ULTIMAKERCONTROLLER
  1013. * PANEL_ONE => ULTIMAKERCONTROLLER
  1014. */
  1015. static_assert(1 >= 0
  1016. #if ENABLED(ULTIMAKERCONTROLLER) \
  1017. && DISABLED(SAV_3DGLCD) && DISABLED(miniVIKI) && DISABLED(VIKI2) \
  1018. && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) && DISABLED(PANEL_ONE)
  1019. + 1
  1020. #endif
  1021. #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
  1022. + 1
  1023. #endif
  1024. #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(BQ_LCD_SMART_CONTROLLER)
  1025. + 1
  1026. #endif
  1027. #if ENABLED(LCD_FOR_MELZI)
  1028. + 1
  1029. #endif
  1030. #if ENABLED(CARTESIO_UI)
  1031. + 1
  1032. #endif
  1033. #if ENABLED(PANEL_ONE)
  1034. + 1
  1035. #endif
  1036. #if ENABLED(MAKRPANEL)
  1037. + 1
  1038. #endif
  1039. #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
  1040. + 1
  1041. #endif
  1042. #if ENABLED(VIKI2)
  1043. + 1
  1044. #endif
  1045. #if ENABLED(miniVIKI)
  1046. + 1
  1047. #endif
  1048. #if ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
  1049. + 1
  1050. #endif
  1051. #if ENABLED(G3D_PANEL)
  1052. + 1
  1053. #endif
  1054. #if ENABLED(MINIPANEL)
  1055. + 1
  1056. #endif
  1057. #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI) && DISABLED(ANET_KEYPAD_LCD)
  1058. + 1
  1059. #endif
  1060. #if ENABLED(RIGIDBOT_PANEL)
  1061. + 1
  1062. #endif
  1063. #if ENABLED(RA_CONTROL_PANEL)
  1064. + 1
  1065. #endif
  1066. #if ENABLED(LCD_I2C_SAINSMART_YWROBOT)
  1067. + 1
  1068. #endif
  1069. #if ENABLED(LCM1602)
  1070. + 1
  1071. #endif
  1072. #if ENABLED(LCD_I2C_PANELOLU2)
  1073. + 1
  1074. #endif
  1075. #if ENABLED(LCD_I2C_VIKI)
  1076. + 1
  1077. #endif
  1078. #if ENABLED(U8GLIB_SSD1306) && DISABLED(OLED_PANEL_TINYBOY2)
  1079. + 1
  1080. #endif
  1081. #if ENABLED(SAV_3DLCD)
  1082. + 1
  1083. #endif
  1084. #if ENABLED(BQ_LCD_SMART_CONTROLLER)
  1085. + 1
  1086. #endif
  1087. #if ENABLED(SAV_3DGLCD)
  1088. + 1
  1089. #endif
  1090. #if ENABLED(OLED_PANEL_TINYBOY2)
  1091. + 1
  1092. #endif
  1093. #if ENABLED(ANET_KEYPAD_LCD)
  1094. + 1
  1095. #endif
  1096. , "Please select no more than one LCD controller option."
  1097. );
  1098. /**
  1099. * Make sure HAVE_TMCDRIVER is warranted
  1100. */
  1101. #if ENABLED(HAVE_TMCDRIVER) && !( \
  1102. ENABLED( X_IS_TMC ) \
  1103. || ENABLED( X2_IS_TMC ) \
  1104. || ENABLED( Y_IS_TMC ) \
  1105. || ENABLED( Y2_IS_TMC ) \
  1106. || ENABLED( Z_IS_TMC ) \
  1107. || ENABLED( Z2_IS_TMC ) \
  1108. || ENABLED( E0_IS_TMC ) \
  1109. || ENABLED( E1_IS_TMC ) \
  1110. || ENABLED( E2_IS_TMC ) \
  1111. || ENABLED( E3_IS_TMC ) \
  1112. || ENABLED( E4_IS_TMC ) \
  1113. )
  1114. #error "HAVE_TMCDRIVER requires at least one TMC stepper to be set."
  1115. #endif
  1116. /**
  1117. * Make sure HAVE_TMC2130 is warranted
  1118. */
  1119. #if ENABLED(HAVE_TMC2130)
  1120. #if !( ENABLED( X_IS_TMC2130 ) \
  1121. || ENABLED( X2_IS_TMC2130 ) \
  1122. || ENABLED( Y_IS_TMC2130 ) \
  1123. || ENABLED( Y2_IS_TMC2130 ) \
  1124. || ENABLED( Z_IS_TMC2130 ) \
  1125. || ENABLED( Z2_IS_TMC2130 ) \
  1126. || ENABLED( E0_IS_TMC2130 ) \
  1127. || ENABLED( E1_IS_TMC2130 ) \
  1128. || ENABLED( E2_IS_TMC2130 ) \
  1129. || ENABLED( E3_IS_TMC2130 ) \
  1130. || ENABLED( E4_IS_TMC2130 ) \
  1131. )
  1132. #error "HAVE_TMC2130 requires at least one TMC2130 stepper to be set."
  1133. #elif ENABLED(HYBRID_THRESHOLD) && DISABLED(STEALTHCHOP)
  1134. #error "Enable STEALTHCHOP to use HYBRID_THRESHOLD."
  1135. #endif
  1136. #endif
  1137. /**
  1138. * Make sure HAVE_L6470DRIVER is warranted
  1139. */
  1140. #if ENABLED(HAVE_L6470DRIVER) && !( \
  1141. ENABLED( X_IS_L6470 ) \
  1142. || ENABLED( X2_IS_L6470 ) \
  1143. || ENABLED( Y_IS_L6470 ) \
  1144. || ENABLED( Y2_IS_L6470 ) \
  1145. || ENABLED( Z_IS_L6470 ) \
  1146. || ENABLED( Z2_IS_L6470 ) \
  1147. || ENABLED( E0_IS_L6470 ) \
  1148. || ENABLED( E1_IS_L6470 ) \
  1149. || ENABLED( E2_IS_L6470 ) \
  1150. || ENABLED( E3_IS_L6470 ) \
  1151. || ENABLED( E4_IS_L6470 ) \
  1152. )
  1153. #error "HAVE_L6470DRIVER requires at least one L6470 stepper to be set."
  1154. #endif
  1155. /**
  1156. * Digipot requirement
  1157. */
  1158. #if ENABLED(DIGIPOT_MCP4018)
  1159. #if !defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) \
  1160. || !defined(DIGIPOTS_I2C_SDA_E0) || !defined(DIGIPOTS_I2C_SDA_E1)
  1161. #error "DIGIPOT_MCP4018 requires DIGIPOTS_I2C_SDA_* pins to be defined."
  1162. #endif
  1163. #endif
  1164. /**
  1165. * Require 4 or more elements in per-axis initializers
  1166. */
  1167. constexpr float sanity_arr_1[] = DEFAULT_AXIS_STEPS_PER_UNIT,
  1168. sanity_arr_2[] = DEFAULT_MAX_FEEDRATE,
  1169. sanity_arr_3[] = DEFAULT_MAX_ACCELERATION;
  1170. static_assert(COUNT(sanity_arr_1) >= XYZE, "DEFAULT_AXIS_STEPS_PER_UNIT requires 4 (or more) elements.");
  1171. static_assert(COUNT(sanity_arr_2) >= XYZE, "DEFAULT_MAX_FEEDRATE requires 4 (or more) elements.");
  1172. static_assert(COUNT(sanity_arr_3) >= XYZE, "DEFAULT_MAX_ACCELERATION requires 4 (or more) elements.");
  1173. static_assert(COUNT(sanity_arr_1) <= XYZE_N, "DEFAULT_AXIS_STEPS_PER_UNIT has too many elements.");
  1174. static_assert(COUNT(sanity_arr_2) <= XYZE_N, "DEFAULT_MAX_FEEDRATE has too many elements.");
  1175. static_assert(COUNT(sanity_arr_3) <= XYZE_N, "DEFAULT_MAX_ACCELERATION has too many elements.");
  1176. /**
  1177. * Sanity checks for Spindle / Laser
  1178. */
  1179. #if ENABLED(SPINDLE_LASER_ENABLE)
  1180. #if !PIN_EXISTS(SPINDLE_LASER_ENABLE)
  1181. #error "SPINDLE_LASER_ENABLE requires SPINDLE_LASER_ENABLE_PIN."
  1182. #elif SPINDLE_DIR_CHANGE && !PIN_EXISTS(SPINDLE_DIR)
  1183. #error "SPINDLE_DIR_PIN not defined."
  1184. #elif ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
  1185. #if !(WITHIN(SPINDLE_LASER_PWM_PIN, 2, 13) || WITHIN(SPINDLE_LASER_PWM_PIN, 44, 46))
  1186. #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin."
  1187. #elif SPINDLE_LASER_POWERUP_DELAY < 1
  1188. #error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0."
  1189. #elif SPINDLE_LASER_POWERDOWN_DELAY < 1
  1190. #error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0."
  1191. #elif !defined(SPINDLE_LASER_PWM_INVERT)
  1192. #error "SPINDLE_LASER_PWM_INVERT missing."
  1193. #elif !defined(SPEED_POWER_SLOPE) || !defined(SPEED_POWER_INTERCEPT) || !defined(SPEED_POWER_MIN) || !defined(SPEED_POWER_MAX)
  1194. #error "SPINDLE_LASER_PWM equation constant(s) missing."
  1195. #elif SPINDLE_LASER_PWM_PIN == 4 || WITHIN(SPINDLE_LASER_PWM_PIN, 11, 13)
  1196. #error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by a system interrupt."
  1197. #elif PIN_EXISTS(X_MAX) && X_MAX_PIN == SPINDLE_LASER_PWM_PIN
  1198. #error "SPINDLE_LASER_PWM pin is in use by X_MAX endstop."
  1199. #elif PIN_EXISTS(X_MIN) && X_MIN_PIN == SPINDLE_LASER_PWM_PIN
  1200. #error "SPINDLE_LASER_PWM pin is in use by X_MIN endstop."
  1201. #elif PIN_EXISTS(Z_STEP) && Z_STEP_PIN == SPINDLE_LASER_PWM_PIN
  1202. #error "SPINDLE_LASER_PWM pin in use by Z_STEP."
  1203. #elif NUM_SERVOS > 0 && (WITHIN(SPINDLE_LASER_PWM_PIN, 2, 3) || SPINDLE_LASER_PWM_PIN == 5)
  1204. #error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by the servo system."
  1205. #elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
  1206. #error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT_PIN."
  1207. #elif PIN_EXISTS(E0_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E0_AUTO_FAN_PIN
  1208. #error "SPINDLE_LASER_PWM_PIN is used by E0_AUTO_FAN_PIN."
  1209. #elif PIN_EXISTS(E1_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E1_AUTO_FAN_PIN
  1210. #error "SPINDLE_LASER_PWM_PIN is used by E1_AUTO_FAN_PIN."
  1211. #elif PIN_EXISTS(E2_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E2_AUTO_FAN_PIN
  1212. #error "SPINDLE_LASER_PWM_PIN is used by E2_AUTO_FAN_PIN."
  1213. #elif PIN_EXISTS(E3_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E3_AUTO_FAN_PIN
  1214. #error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
  1215. #elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
  1216. #error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
  1217. #elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
  1218. #error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
  1219. #elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN
  1220. #error "SPINDLE_LASER_PWM_PIN is used FAN1_PIN."
  1221. #elif PIN_EXISTS(FAN2) && SPINDLE_LASER_PWM_PIN == FAN2_PIN
  1222. #error "SPINDLE_LASER_PWM_PIN is used FAN2_PIN."
  1223. #elif PIN_EXISTS(CONTROLLERFAN) && SPINDLE_LASER_PWM_PIN == CONTROLLERFAN_PIN
  1224. #error "SPINDLE_LASER_PWM_PIN is used by CONTROLLERFAN_PIN."
  1225. #elif PIN_EXISTS(MOTOR_CURRENT_PWM_XY) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_XY_PIN
  1226. #error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_XY."
  1227. #elif PIN_EXISTS(MOTOR_CURRENT_PWM_Z) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_Z_PIN
  1228. #error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_Z."
  1229. #elif PIN_EXISTS(MOTOR_CURRENT_PWM_E) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_E_PIN
  1230. #error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_E."
  1231. #elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
  1232. #error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT."
  1233. #endif
  1234. #endif
  1235. #endif // SPINDLE_LASER_ENABLE