1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720172117221723172417251726172717281729173017311732173317341735173617371738173917401741174217431744174517461747174817491750175117521753175417551756175717581759176017611762176317641765176617671768176917701771177217731774177517761777177817791780178117821783178417851786178717881789179017911792179317941795179617971798179918001801180218031804180518061807180818091810181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391840184118421843184418451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906190719081909191019111912191319141915191619171918191919201921192219231924192519261927192819291930193119321933193419351936193719381939194019411942194319441945194619471948194919501951195219531954195519561957195819591960196119621963196419651966196719681969197019711972197319741975197619771978197919801981198219831984198519861987198819891990199119921993199419951996199719981999200020012002200320042005200620072008200920102011201220132014201520162017201820192020202120222023202420252026202720282029203020312032203320342035203620372038203920402041204220432044204520462047204820492050205120522053205420552056205720582059206020612062206320642065206620672068206920702071207220732074207520762077207820792080208120822083208420852086208720882089209020912092209320942095209620972098209921002101210221032104210521062107210821092110211121122113211421152116211721182119212021212122212321242125212621272128212921302131213221332134213521362137213821392140214121422143214421452146214721482149215021512152215321542155215621572158215921602161216221632164216521662167216821692170217121722173217421752176217721782179218021812182218321842185218621872188218921902191219221932194219521962197219821992200220122022203220422052206220722082209221022112212221322142215221622172218221922202221222222232224222522262227222822292230223122322233223422352236223722382239224022412242224322442245224622472248224922502251225222532254225522562257225822592260226122622263226422652266226722682269227022712272227322742275227622772278227922802281228222832284228522862287228822892290229122922293229422952296229722982299230023012302230323042305230623072308230923102311231223132314231523162317231823192320232123222323232423252326232723282329233023312332233323342335233623372338233923402341234223432344234523462347234823492350235123522353235423552356235723582359236023612362236323642365236623672368236923702371237223732374237523762377237823792380238123822383238423852386238723882389239023912392239323942395239623972398239924002401240224032404240524062407240824092410241124122413241424152416241724182419242024212422242324242425242624272428242924302431243224332434243524362437243824392440244124422443244424452446244724482449245024512452245324542455245624572458245924602461246224632464246524662467246824692470247124722473247424752476247724782479248024812482248324842485248624872488248924902491249224932494249524962497249824992500250125022503250425052506250725082509251025112512251325142515251625172518251925202521252225232524252525262527252825292530253125322533253425352536253725382539254025412542254325442545254625472548254925502551255225532554255525562557255825592560256125622563256425652566256725682569257025712572257325742575257625772578257925802581258225832584258525862587258825892590259125922593259425952596259725982599260026012602260326042605260626072608260926102611261226132614261526162617261826192620262126222623262426252626262726282629263026312632263326342635263626372638263926402641264226432644264526462647264826492650265126522653265426552656265726582659266026612662266326642665266626672668266926702671267226732674267526762677267826792680268126822683268426852686268726882689269026912692269326942695269626972698269927002701270227032704270527062707270827092710271127122713271427152716271727182719272027212722272327242725272627272728272927302731273227332734273527362737273827392740274127422743274427452746274727482749275027512752275327542755275627572758275927602761276227632764276527662767276827692770277127722773277427752776277727782779278027812782278327842785278627872788278927902791279227932794279527962797279827992800280128022803280428052806280728082809281028112812281328142815281628172818281928202821282228232824282528262827282828292830283128322833283428352836283728382839284028412842284328442845284628472848284928502851285228532854285528562857285828592860286128622863286428652866286728682869287028712872287328742875287628772878287928802881288228832884288528862887288828892890289128922893289428952896289728982899290029012902290329042905290629072908290929102911291229132914291529162917291829192920292129222923292429252926292729282929293029312932293329342935293629372938293929402941294229432944294529462947294829492950295129522953295429552956295729582959296029612962296329642965296629672968296929702971297229732974297529762977297829792980298129822983298429852986298729882989299029912992299329942995299629972998299930003001300230033004300530063007300830093010301130123013301430153016301730183019302030213022302330243025302630273028302930303031303230333034303530363037303830393040304130423043304430453046304730483049305030513052305330543055305630573058305930603061306230633064306530663067306830693070307130723073307430753076307730783079308030813082308330843085308630873088308930903091309230933094309530963097309830993100310131023103310431053106310731083109311031113112311331143115311631173118311931203121312231233124312531263127312831293130313131323133313431353136313731383139314031413142314331443145314631473148314931503151315231533154315531563157315831593160316131623163316431653166316731683169317031713172317331743175317631773178317931803181318231833184318531863187318831893190319131923193319431953196319731983199320032013202320332043205320632073208320932103211321232133214321532163217321832193220322132223223322432253226322732283229323032313232323332343235323632373238323932403241324232433244324532463247324832493250325132523253325432553256325732583259326032613262326332643265326632673268326932703271327232733274327532763277327832793280328132823283328432853286328732883289329032913292329332943295329632973298329933003301330233033304330533063307330833093310331133123313331433153316331733183319332033213322332333243325332633273328332933303331333233333334333533363337333833393340334133423343334433453346334733483349335033513352335333543355335633573358335933603361336233633364336533663367336833693370337133723373337433753376337733783379338033813382338333843385338633873388338933903391339233933394339533963397339833993400340134023403340434053406340734083409341034113412341334143415341634173418341934203421342234233424342534263427342834293430343134323433343434353436343734383439344034413442344334443445344634473448344934503451345234533454345534563457345834593460346134623463346434653466346734683469347034713472347334743475347634773478347934803481348234833484348534863487348834893490349134923493349434953496349734983499350035013502350335043505350635073508350935103511351235133514351535163517351835193520352135223523352435253526352735283529353035313532353335343535353635373538353935403541354235433544354535463547354835493550355135523553355435553556355735583559356035613562356335643565356635673568356935703571357235733574357535763577357835793580358135823583358435853586358735883589359035913592359335943595359635973598359936003601360236033604360536063607360836093610361136123613361436153616361736183619362036213622362336243625362636273628362936303631363236333634363536363637363836393640364136423643364436453646364736483649365036513652 |
- /**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <https://www.gnu.org/licenses/>.
- *
- */
-
- /**
- * settings.cpp
- *
- * Settings and EEPROM storage
- *
- * IMPORTANT: Whenever there are changes made to the variables stored in EEPROM
- * in the functions below, also increment the version number. This makes sure that
- * the default values are used whenever there is a change to the data, to prevent
- * wrong data being written to the variables.
- *
- * ALSO: Variables in the Store and Retrieve sections must be in the same order.
- * If a feature is disabled, some data must still be written that, when read,
- * either sets a Sane Default, or results in No Change to the existing value.
- */
-
- // Change EEPROM version if the structure changes
- #define EEPROM_VERSION "V87"
- #define EEPROM_OFFSET 100
-
- // Check the integrity of data offsets.
- // Can be disabled for production build.
- //#define DEBUG_EEPROM_READWRITE
-
- #include "settings.h"
-
- #include "endstops.h"
- #include "planner.h"
- #include "stepper.h"
- #include "temperature.h"
-
- #include "../lcd/marlinui.h"
- #include "../libs/vector_3.h" // for matrix_3x3
- #include "../gcode/gcode.h"
- #include "../MarlinCore.h"
-
- #if EITHER(EEPROM_SETTINGS, SD_FIRMWARE_UPDATE)
- #include "../HAL/shared/eeprom_api.h"
- #endif
-
- #include "probe.h"
-
- #if HAS_LEVELING
- #include "../feature/bedlevel/bedlevel.h"
- #if ENABLED(X_AXIS_TWIST_COMPENSATION)
- #include "../feature/x_twist.h"
- #endif
- #endif
-
- #if ENABLED(Z_STEPPER_AUTO_ALIGN)
- #include "../feature/z_stepper_align.h"
- #endif
-
- #if ENABLED(EXTENSIBLE_UI)
- #include "../lcd/extui/ui_api.h"
- #elif ENABLED(DWIN_LCD_PROUI)
- #include "../lcd/e3v2/proui/dwin.h"
- #include "../lcd/e3v2/proui/bedlevel_tools.h"
- #elif ENABLED(DWIN_CREALITY_LCD_JYERSUI)
- #include "../lcd/e3v2/jyersui/dwin.h"
- #endif
-
- #if ENABLED(HOST_PROMPT_SUPPORT)
- #include "../feature/host_actions.h"
- #endif
-
- #if HAS_SERVOS
- #include "servo.h"
- #endif
-
- #if HAS_SERVOS && HAS_SERVO_ANGLES
- #define EEPROM_NUM_SERVOS NUM_SERVOS
- #else
- #define EEPROM_NUM_SERVOS NUM_SERVO_PLUGS
- #endif
-
- #include "../feature/fwretract.h"
-
- #if ENABLED(POWER_LOSS_RECOVERY)
- #include "../feature/powerloss.h"
- #endif
-
- #if HAS_POWER_MONITOR
- #include "../feature/power_monitor.h"
- #endif
-
- #include "../feature/pause.h"
-
- #if ENABLED(BACKLASH_COMPENSATION)
- #include "../feature/backlash.h"
- #endif
-
- #if HAS_FILAMENT_SENSOR
- #include "../feature/runout.h"
- #ifndef FIL_RUNOUT_ENABLED_DEFAULT
- #define FIL_RUNOUT_ENABLED_DEFAULT true
- #endif
- #endif
-
- #if ENABLED(ADVANCE_K_EXTRA)
- extern float other_extruder_advance_K[DISTINCT_E];
- #endif
-
- #if HAS_MULTI_EXTRUDER
- #include "tool_change.h"
- void M217_report(const bool eeprom);
- #endif
-
- #if ENABLED(BLTOUCH)
- #include "../feature/bltouch.h"
- #endif
-
- #if HAS_TRINAMIC_CONFIG
- #include "stepper/indirection.h"
- #include "../feature/tmc_util.h"
- #endif
-
- #if HAS_PTC
- #include "../feature/probe_temp_comp.h"
- #endif
-
- #include "../feature/controllerfan.h"
-
- #if ENABLED(CASE_LIGHT_ENABLE)
- #include "../feature/caselight.h"
- #endif
-
- #if ENABLED(PASSWORD_FEATURE)
- #include "../feature/password/password.h"
- #endif
-
- #if ENABLED(TOUCH_SCREEN_CALIBRATION)
- #include "../lcd/tft_io/touch_calibration.h"
- #endif
-
- #if HAS_ETHERNET
- #include "../feature/ethernet.h"
- #endif
-
- #if ENABLED(SOUND_MENU_ITEM)
- #include "../libs/buzzer.h"
- #endif
-
- #if HAS_FANCHECK
- #include "../feature/fancheck.h"
- #endif
-
- #if ENABLED(DGUS_LCD_UI_MKS)
- #include "../lcd/extui/dgus/DGUSScreenHandler.h"
- #include "../lcd/extui/dgus/DGUSDisplayDef.h"
- #endif
-
- #pragma pack(push, 1) // No padding between variables
-
- #if HAS_ETHERNET
- void ETH0_report();
- void MAC_report();
- #endif
-
- #define _EN_ITEM(N) , E##N
- #define _EN1_ITEM(N) , E##N:1
-
- typedef struct { uint16_t MAIN_AXIS_NAMES, X2, Y2, Z2, Z3, Z4 REPEAT(E_STEPPERS, _EN_ITEM); } per_stepper_uint16_t;
- typedef struct { uint32_t MAIN_AXIS_NAMES, X2, Y2, Z2, Z3, Z4 REPEAT(E_STEPPERS, _EN_ITEM); } per_stepper_uint32_t;
- typedef struct { int16_t MAIN_AXIS_NAMES, X2, Y2, Z2, Z3, Z4; } mot_stepper_int16_t;
- typedef struct { bool NUM_AXIS_LIST(X:1, Y:1, Z:1, I:1, J:1, K:1, U:1, V:1, W:1), X2:1, Y2:1, Z2:1, Z3:1, Z4:1 REPEAT(E_STEPPERS, _EN1_ITEM); } per_stepper_bool_t;
-
- #undef _EN_ITEM
-
- // Limit an index to an array size
- #define ALIM(I,ARR) _MIN(I, (signed)COUNT(ARR) - 1)
-
- // Defaults for reset / fill in on load
- static const uint32_t _DMA[] PROGMEM = DEFAULT_MAX_ACCELERATION;
- static const float _DASU[] PROGMEM = DEFAULT_AXIS_STEPS_PER_UNIT;
- static const feedRate_t _DMF[] PROGMEM = DEFAULT_MAX_FEEDRATE;
-
- /**
- * Current EEPROM Layout
- *
- * Keep this data structure up to date so
- * EEPROM size is known at compile time!
- */
- typedef struct SettingsDataStruct {
- char version[4]; // Vnn\0
- #if ENABLED(EEPROM_INIT_NOW)
- uint32_t build_hash; // Unique build hash
- #endif
- uint16_t crc; // Data Checksum
-
- //
- // DISTINCT_E_FACTORS
- //
- uint8_t e_factors; // DISTINCT_AXES - NUM_AXES
-
- //
- // Planner settings
- //
- planner_settings_t planner_settings;
-
- xyze_float_t planner_max_jerk; // M205 XYZE planner.max_jerk
- float planner_junction_deviation_mm; // M205 J planner.junction_deviation_mm
-
- //
- // Home Offset
- //
- xyz_pos_t home_offset; // M206 XYZ / M665 TPZ
-
- //
- // Hotend Offset
- //
- #if HAS_HOTEND_OFFSET
- xyz_pos_t hotend_offset[HOTENDS - 1]; // M218 XYZ
- #endif
-
- //
- // FILAMENT_RUNOUT_SENSOR
- //
- bool runout_sensor_enabled; // M412 S
- float runout_distance_mm; // M412 D
-
- //
- // ENABLE_LEVELING_FADE_HEIGHT
- //
- float planner_z_fade_height; // M420 Zn planner.z_fade_height
-
- //
- // MESH_BED_LEVELING
- //
- float mbl_z_offset; // bedlevel.z_offset
- uint8_t mesh_num_x, mesh_num_y; // GRID_MAX_POINTS_X, GRID_MAX_POINTS_Y
- float mbl_z_values[TERN(MESH_BED_LEVELING, GRID_MAX_POINTS_X, 3)] // bedlevel.z_values
- [TERN(MESH_BED_LEVELING, GRID_MAX_POINTS_Y, 3)];
-
- //
- // HAS_BED_PROBE
- //
-
- xyz_pos_t probe_offset; // M851 X Y Z
-
- //
- // ABL_PLANAR
- //
- matrix_3x3 planner_bed_level_matrix; // planner.bed_level_matrix
-
- //
- // AUTO_BED_LEVELING_BILINEAR
- //
- uint8_t grid_max_x, grid_max_y; // GRID_MAX_POINTS_X, GRID_MAX_POINTS_Y
- xy_pos_t bilinear_grid_spacing, bilinear_start; // G29 L F
- #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
- bed_mesh_t z_values; // G29
- #else
- float z_values[3][3];
- #endif
-
- //
- // X_AXIS_TWIST_COMPENSATION
- //
- #if ENABLED(X_AXIS_TWIST_COMPENSATION)
- float xatc_spacing; // M423 X Z
- float xatc_start;
- xatc_array_t xatc_z_offset;
- #endif
-
- //
- // AUTO_BED_LEVELING_UBL
- //
- bool planner_leveling_active; // M420 S planner.leveling_active
- int8_t ubl_storage_slot; // bedlevel.storage_slot
-
- //
- // SERVO_ANGLES
- //
- uint16_t servo_angles[EEPROM_NUM_SERVOS][2]; // M281 P L U
-
- //
- // Temperature first layer compensation values
- //
- #if HAS_PTC
- #if ENABLED(PTC_PROBE)
- int16_t z_offsets_probe[COUNT(ptc.z_offsets_probe)]; // M871 P I V
- #endif
- #if ENABLED(PTC_BED)
- int16_t z_offsets_bed[COUNT(ptc.z_offsets_bed)]; // M871 B I V
- #endif
- #if ENABLED(PTC_HOTEND)
- int16_t z_offsets_hotend[COUNT(ptc.z_offsets_hotend)]; // M871 E I V
- #endif
- #endif
-
- //
- // BLTOUCH
- //
- bool bltouch_od_5v_mode;
- #ifdef BLTOUCH_HS_MODE
- bool bltouch_high_speed_mode; // M401 S
- #endif
-
- //
- // Kinematic Settings
- //
- #if IS_KINEMATIC
- float segments_per_second; // M665 S
- #if ENABLED(DELTA)
- float delta_height; // M666 H
- abc_float_t delta_endstop_adj; // M666 X Y Z
- float delta_radius, // M665 R
- delta_diagonal_rod; // M665 L
- abc_float_t delta_tower_angle_trim, // M665 X Y Z
- delta_diagonal_rod_trim; // M665 A B C
- #elif ENABLED(POLARGRAPH)
- xy_pos_t draw_area_min, draw_area_max; // M665 L R T B
- float polargraph_max_belt_len; // M665 H
- #endif
-
- #endif
-
- //
- // Extra Endstops offsets
- //
- #if HAS_EXTRA_ENDSTOPS
- float x2_endstop_adj, // M666 X
- y2_endstop_adj, // M666 Y
- z2_endstop_adj, // M666 (S2) Z
- z3_endstop_adj, // M666 (S3) Z
- z4_endstop_adj; // M666 (S4) Z
- #endif
-
- //
- // Z_STEPPER_AUTO_ALIGN, HAS_Z_STEPPER_ALIGN_STEPPER_XY
- //
- #if ENABLED(Z_STEPPER_AUTO_ALIGN)
- xy_pos_t z_stepper_align_xy[NUM_Z_STEPPERS]; // M422 S X Y
- #if HAS_Z_STEPPER_ALIGN_STEPPER_XY
- xy_pos_t z_stepper_align_stepper_xy[NUM_Z_STEPPERS]; // M422 W X Y
- #endif
- #endif
-
- //
- // Material Presets
- //
- #if HAS_PREHEAT
- preheat_t ui_material_preset[PREHEAT_COUNT]; // M145 S0 H B F
- #endif
-
- //
- // PIDTEMP
- //
- raw_pidcf_t hotendPID[HOTENDS]; // M301 En PIDCF / M303 En U
- int16_t lpq_len; // M301 L
-
- //
- // PIDTEMPBED
- //
- raw_pid_t bedPID; // M304 PID / M303 E-1 U
-
- //
- // PIDTEMPCHAMBER
- //
- raw_pid_t chamberPID; // M309 PID / M303 E-2 U
-
- //
- // User-defined Thermistors
- //
- #if HAS_USER_THERMISTORS
- user_thermistor_t user_thermistor[USER_THERMISTORS]; // M305 P0 R4700 T100000 B3950
- #endif
-
- //
- // Power monitor
- //
- uint8_t power_monitor_flags; // M430 I V W
-
- //
- // HAS_LCD_CONTRAST
- //
- uint8_t lcd_contrast; // M250 C
-
- //
- // HAS_LCD_BRIGHTNESS
- //
- uint8_t lcd_brightness; // M256 B
-
- //
- // Display Sleep
- //
- #if LCD_BACKLIGHT_TIMEOUT_MINS
- uint8_t backlight_timeout_minutes; // M255 S
- #elif HAS_DISPLAY_SLEEP
- uint8_t sleep_timeout_minutes; // M255 S
- #endif
-
- //
- // Controller fan settings
- //
- controllerFan_settings_t controllerFan_settings; // M710
-
- //
- // POWER_LOSS_RECOVERY
- //
- bool recovery_enabled; // M413 S
-
- //
- // FWRETRACT
- //
- fwretract_settings_t fwretract_settings; // M207 S F Z W, M208 S F W R
- bool autoretract_enabled; // M209 S
-
- //
- // !NO_VOLUMETRIC
- //
- bool parser_volumetric_enabled; // M200 S parser.volumetric_enabled
- float planner_filament_size[EXTRUDERS]; // M200 T D planner.filament_size[]
- float planner_volumetric_extruder_limit[EXTRUDERS]; // M200 T L planner.volumetric_extruder_limit[]
-
- //
- // HAS_TRINAMIC_CONFIG
- //
- per_stepper_uint16_t tmc_stepper_current; // M906 X Y Z...
- per_stepper_uint32_t tmc_hybrid_threshold; // M913 X Y Z...
- mot_stepper_int16_t tmc_sgt; // M914 X Y Z...
- per_stepper_bool_t tmc_stealth_enabled; // M569 X Y Z...
-
- //
- // LIN_ADVANCE
- //
- float planner_extruder_advance_K[DISTINCT_E]; // M900 K planner.extruder_advance_K
-
- //
- // HAS_MOTOR_CURRENT_PWM
- //
- #ifndef MOTOR_CURRENT_COUNT
- #if HAS_MOTOR_CURRENT_PWM
- #define MOTOR_CURRENT_COUNT 3
- #elif HAS_MOTOR_CURRENT_DAC
- #define MOTOR_CURRENT_COUNT LOGICAL_AXES
- #elif HAS_MOTOR_CURRENT_I2C
- #define MOTOR_CURRENT_COUNT DIGIPOT_I2C_NUM_CHANNELS
- #else // HAS_MOTOR_CURRENT_SPI
- #define MOTOR_CURRENT_COUNT DISTINCT_AXES
- #endif
- #endif
- uint32_t motor_current_setting[MOTOR_CURRENT_COUNT]; // M907 X Z E ...
-
- //
- // CNC_COORDINATE_SYSTEMS
- //
- xyz_pos_t coordinate_system[MAX_COORDINATE_SYSTEMS]; // G54-G59.3
-
- //
- // SKEW_CORRECTION
- //
- skew_factor_t planner_skew_factor; // M852 I J K
-
- //
- // ADVANCED_PAUSE_FEATURE
- //
- #if HAS_EXTRUDERS
- fil_change_settings_t fc_settings[EXTRUDERS]; // M603 T U L
- #endif
-
- //
- // Tool-change settings
- //
- #if HAS_MULTI_EXTRUDER
- toolchange_settings_t toolchange_settings; // M217 S P R
- #endif
-
- //
- // BACKLASH_COMPENSATION
- //
- xyz_float_t backlash_distance_mm; // M425 X Y Z
- uint8_t backlash_correction; // M425 F
- float backlash_smoothing_mm; // M425 S
-
- //
- // EXTENSIBLE_UI
- //
- #if ENABLED(EXTENSIBLE_UI)
- uint8_t extui_data[ExtUI::eeprom_data_size];
- #endif
-
- //
- // Ender-3 V2 DWIN
- //
- #if ENABLED(DWIN_LCD_PROUI)
- uint8_t dwin_data[eeprom_data_size];
- #elif ENABLED(DWIN_CREALITY_LCD_JYERSUI)
- uint8_t dwin_settings[CrealityDWIN.eeprom_data_size];
- #endif
-
- //
- // CASELIGHT_USES_BRIGHTNESS
- //
- #if CASELIGHT_USES_BRIGHTNESS
- uint8_t caselight_brightness; // M355 P
- #endif
-
- //
- // PASSWORD_FEATURE
- //
- #if ENABLED(PASSWORD_FEATURE)
- bool password_is_set;
- uint32_t password_value;
- #endif
-
- //
- // TOUCH_SCREEN_CALIBRATION
- //
- #if ENABLED(TOUCH_SCREEN_CALIBRATION)
- touch_calibration_t touch_calibration_data;
- #endif
-
- // Ethernet settings
- #if HAS_ETHERNET
- bool ethernet_hardware_enabled; // M552 S
- uint32_t ethernet_ip, // M552 P
- ethernet_dns,
- ethernet_gateway, // M553 P
- ethernet_subnet; // M554 P
- #endif
-
- //
- // Buzzer enable/disable
- //
- #if ENABLED(SOUND_MENU_ITEM)
- bool sound_on;
- #endif
-
- //
- // Fan tachometer check
- //
- #if HAS_FANCHECK
- bool fan_check_enabled;
- #endif
-
- //
- // MKS UI controller
- //
- #if ENABLED(DGUS_LCD_UI_MKS)
- MKS_Language mks_language_index; // Display Language
- xy_int_t mks_corner_offsets[5]; // Bed Tramming
- xyz_int_t mks_park_pos; // Custom Parking (without NOZZLE_PARK)
- celsius_t mks_min_extrusion_temp; // Min E Temp (shadow M302 value)
- #endif
-
- #if HAS_MULTI_LANGUAGE
- uint8_t ui_language; // M414 S
- #endif
-
- //
- // Model predictive control
- //
- #if ENABLED(MPCTEMP)
- MPC_t mpc_constants[HOTENDS]; // M306
- #endif
-
- } SettingsData;
-
- //static_assert(sizeof(SettingsData) <= MARLIN_EEPROM_SIZE, "EEPROM too small to contain SettingsData!");
-
- MarlinSettings settings;
-
- uint16_t MarlinSettings::datasize() { return sizeof(SettingsData); }
-
- /**
- * Post-process after Retrieve or Reset
- */
-
- #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
- float new_z_fade_height;
- #endif
-
- void MarlinSettings::postprocess() {
- xyze_pos_t oldpos = current_position;
-
- // steps per s2 needs to be updated to agree with units per s2
- planner.refresh_acceleration_rates();
-
- // Make sure delta kinematics are updated before refreshing the
- // planner position so the stepper counts will be set correctly.
- TERN_(DELTA, recalc_delta_settings());
-
- TERN_(PIDTEMP, thermalManager.updatePID());
-
- #if DISABLED(NO_VOLUMETRICS)
- planner.calculate_volumetric_multipliers();
- #elif EXTRUDERS
- for (uint8_t i = COUNT(planner.e_factor); i--;)
- planner.refresh_e_factor(i);
- #endif
-
- // Software endstops depend on home_offset
- LOOP_NUM_AXES(i) {
- update_workspace_offset((AxisEnum)i);
- update_software_endstops((AxisEnum)i);
- }
-
- TERN_(ENABLE_LEVELING_FADE_HEIGHT, set_z_fade_height(new_z_fade_height, false)); // false = no report
-
- TERN_(AUTO_BED_LEVELING_BILINEAR, bedlevel.refresh_bed_level());
-
- TERN_(HAS_MOTOR_CURRENT_PWM, stepper.refresh_motor_power());
-
- TERN_(FWRETRACT, fwretract.refresh_autoretract());
-
- TERN_(HAS_LINEAR_E_JERK, planner.recalculate_max_e_jerk());
-
- TERN_(CASELIGHT_USES_BRIGHTNESS, caselight.update_brightness());
-
- TERN_(EXTENSIBLE_UI, ExtUI::onPostprocessSettings());
-
- // Refresh mm_per_step with the reciprocal of axis_steps_per_mm
- // and init stepper.count[], planner.position[] with current_position
- planner.refresh_positioning();
-
- // Various factors can change the current position
- if (oldpos != current_position)
- report_current_position();
-
- // Moved as last update due to interference with Neopixel init
- TERN_(HAS_LCD_CONTRAST, ui.refresh_contrast());
- TERN_(HAS_LCD_BRIGHTNESS, ui.refresh_brightness());
-
- #if LCD_BACKLIGHT_TIMEOUT_MINS
- ui.refresh_backlight_timeout();
- #elif HAS_DISPLAY_SLEEP && DISABLED(TFT_COLOR_UI)
- ui.refresh_screen_timeout();
- #endif
- }
-
- #if BOTH(PRINTCOUNTER, EEPROM_SETTINGS)
- #include "printcounter.h"
- static_assert(
- !WITHIN(STATS_EEPROM_ADDRESS, EEPROM_OFFSET, EEPROM_OFFSET + sizeof(SettingsData)) &&
- !WITHIN(STATS_EEPROM_ADDRESS + sizeof(printStatistics), EEPROM_OFFSET, EEPROM_OFFSET + sizeof(SettingsData)),
- "STATS_EEPROM_ADDRESS collides with EEPROM settings storage."
- );
- #endif
-
- #if ENABLED(SD_FIRMWARE_UPDATE)
-
- #if ENABLED(EEPROM_SETTINGS)
- static_assert(
- !WITHIN(SD_FIRMWARE_UPDATE_EEPROM_ADDR, EEPROM_OFFSET, EEPROM_OFFSET + sizeof(SettingsData)),
- "SD_FIRMWARE_UPDATE_EEPROM_ADDR collides with EEPROM settings storage."
- );
- #endif
-
- bool MarlinSettings::sd_update_status() {
- uint8_t val;
- persistentStore.read_data(SD_FIRMWARE_UPDATE_EEPROM_ADDR, &val);
- return (val == SD_FIRMWARE_UPDATE_ACTIVE_VALUE);
- }
-
- bool MarlinSettings::set_sd_update_status(const bool enable) {
- if (enable != sd_update_status())
- persistentStore.write_data(
- SD_FIRMWARE_UPDATE_EEPROM_ADDR,
- enable ? SD_FIRMWARE_UPDATE_ACTIVE_VALUE : SD_FIRMWARE_UPDATE_INACTIVE_VALUE
- );
- return true;
- }
-
- #endif // SD_FIRMWARE_UPDATE
-
- #ifdef ARCHIM2_SPI_FLASH_EEPROM_BACKUP_SIZE
- static_assert(EEPROM_OFFSET + sizeof(SettingsData) < ARCHIM2_SPI_FLASH_EEPROM_BACKUP_SIZE,
- "ARCHIM2_SPI_FLASH_EEPROM_BACKUP_SIZE is insufficient to capture all EEPROM data.");
- #endif
-
- //
- // This file simply uses the DEBUG_ECHO macros to implement EEPROM_CHITCHAT.
- // For deeper debugging of EEPROM issues enable DEBUG_EEPROM_READWRITE.
- //
- #define DEBUG_OUT EITHER(EEPROM_CHITCHAT, DEBUG_LEVELING_FEATURE)
- #include "../core/debug_out.h"
-
- #if BOTH(EEPROM_CHITCHAT, HOST_PROMPT_SUPPORT)
- #define HOST_EEPROM_CHITCHAT 1
- #endif
-
- #if ENABLED(EEPROM_SETTINGS)
-
- #define EEPROM_ASSERT(TST,ERR) do{ if (!(TST)) { SERIAL_ERROR_MSG(ERR); eeprom_error = true; } }while(0)
-
- #if ENABLED(DEBUG_EEPROM_READWRITE)
- #define _FIELD_TEST(FIELD) \
- EEPROM_ASSERT( \
- eeprom_error || eeprom_index == offsetof(SettingsData, FIELD) + EEPROM_OFFSET, \
- "Field " STRINGIFY(FIELD) " mismatch." \
- )
- #else
- #define _FIELD_TEST(FIELD) NOOP
- #endif
-
- const char version[4] = EEPROM_VERSION;
-
- #if ENABLED(EEPROM_INIT_NOW)
- constexpr uint32_t strhash32(const char *s, const uint32_t h=0) {
- return *s ? strhash32(s + 1, ((h + *s) << (*s & 3)) ^ *s) : h;
- }
- constexpr uint32_t build_hash = strhash32(__DATE__ __TIME__);
- #endif
-
- bool MarlinSettings::eeprom_error, MarlinSettings::validating;
- int MarlinSettings::eeprom_index;
- uint16_t MarlinSettings::working_crc;
-
- bool MarlinSettings::size_error(const uint16_t size) {
- if (size != datasize()) {
- DEBUG_ERROR_MSG("EEPROM datasize error."
- #if ENABLED(MARLIN_DEV_MODE)
- " (Actual:", size, " Expected:", datasize(), ")"
- #endif
- );
- return true;
- }
- return false;
- }
-
- /**
- * M500 - Store Configuration
- */
- bool MarlinSettings::save() {
- float dummyf = 0;
- char ver[4] = "ERR";
-
- if (!EEPROM_START(EEPROM_OFFSET)) return false;
-
- eeprom_error = false;
-
- // Write or Skip version. (Flash doesn't allow rewrite without erase.)
- TERN(FLASH_EEPROM_EMULATION, EEPROM_SKIP, EEPROM_WRITE)(ver);
-
- #if ENABLED(EEPROM_INIT_NOW)
- EEPROM_SKIP(build_hash); // Skip the hash slot
- #endif
-
- EEPROM_SKIP(working_crc); // Skip the checksum slot
-
- working_crc = 0; // clear before first "real data"
-
- const uint8_t e_factors = DISTINCT_AXES - (NUM_AXES);
- _FIELD_TEST(e_factors);
- EEPROM_WRITE(e_factors);
-
- //
- // Planner Motion
- //
- {
- EEPROM_WRITE(planner.settings);
-
- #if HAS_CLASSIC_JERK
- EEPROM_WRITE(planner.max_jerk);
- #if HAS_LINEAR_E_JERK
- dummyf = float(DEFAULT_EJERK);
- EEPROM_WRITE(dummyf);
- #endif
- #else
- const xyze_pos_t planner_max_jerk = LOGICAL_AXIS_ARRAY(float(DEFAULT_EJERK), 10, 10, 0.4, 0.4, 0.4, 0.4, 0.4, 0.4, 0.4);
- EEPROM_WRITE(planner_max_jerk);
- #endif
-
- TERN_(CLASSIC_JERK, dummyf = 0.02f);
- EEPROM_WRITE(TERN(CLASSIC_JERK, dummyf, planner.junction_deviation_mm));
- }
-
- //
- // Home Offset
- //
- {
- _FIELD_TEST(home_offset);
-
- #if HAS_SCARA_OFFSET
- EEPROM_WRITE(scara_home_offset);
- #else
- #if !HAS_HOME_OFFSET
- const xyz_pos_t home_offset{0};
- #endif
- EEPROM_WRITE(home_offset);
- #endif
- }
-
- //
- // Hotend Offsets, if any
- //
- {
- #if HAS_HOTEND_OFFSET
- // Skip hotend 0 which must be 0
- LOOP_S_L_N(e, 1, HOTENDS)
- EEPROM_WRITE(hotend_offset[e]);
- #endif
- }
-
- //
- // Filament Runout Sensor
- //
- {
- #if HAS_FILAMENT_SENSOR
- const bool &runout_sensor_enabled = runout.enabled;
- #else
- constexpr int8_t runout_sensor_enabled = -1;
- #endif
- _FIELD_TEST(runout_sensor_enabled);
- EEPROM_WRITE(runout_sensor_enabled);
-
- #if HAS_FILAMENT_RUNOUT_DISTANCE
- const float &runout_distance_mm = runout.runout_distance();
- #else
- constexpr float runout_distance_mm = 0;
- #endif
- EEPROM_WRITE(runout_distance_mm);
- }
-
- //
- // Global Leveling
- //
- {
- const float zfh = TERN(ENABLE_LEVELING_FADE_HEIGHT, planner.z_fade_height, (DEFAULT_LEVELING_FADE_HEIGHT));
- EEPROM_WRITE(zfh);
- }
-
- //
- // Mesh Bed Leveling
- //
- {
- #if ENABLED(MESH_BED_LEVELING)
- static_assert(
- sizeof(bedlevel.z_values) == (GRID_MAX_POINTS) * sizeof(bedlevel.z_values[0][0]),
- "MBL Z array is the wrong size."
- );
- #else
- dummyf = 0;
- #endif
-
- const uint8_t mesh_num_x = TERN(MESH_BED_LEVELING, GRID_MAX_POINTS_X, 3),
- mesh_num_y = TERN(MESH_BED_LEVELING, GRID_MAX_POINTS_Y, 3);
-
- EEPROM_WRITE(TERN(MESH_BED_LEVELING, bedlevel.z_offset, dummyf));
- EEPROM_WRITE(mesh_num_x);
- EEPROM_WRITE(mesh_num_y);
-
- #if ENABLED(MESH_BED_LEVELING)
- EEPROM_WRITE(bedlevel.z_values);
- #else
- for (uint8_t q = mesh_num_x * mesh_num_y; q--;) EEPROM_WRITE(dummyf);
- #endif
- }
-
- //
- // Probe XYZ Offsets
- //
- {
- _FIELD_TEST(probe_offset);
- #if HAS_BED_PROBE
- const xyz_pos_t &zpo = probe.offset;
- #else
- constexpr xyz_pos_t zpo{0};
- #endif
- EEPROM_WRITE(zpo);
- }
-
- //
- // Planar Bed Leveling matrix
- //
- {
- #if ABL_PLANAR
- EEPROM_WRITE(planner.bed_level_matrix);
- #else
- dummyf = 0;
- for (uint8_t q = 9; q--;) EEPROM_WRITE(dummyf);
- #endif
- }
-
- //
- // Bilinear Auto Bed Leveling
- //
- {
- #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
- static_assert(
- sizeof(bedlevel.z_values) == (GRID_MAX_POINTS) * sizeof(bedlevel.z_values[0][0]),
- "Bilinear Z array is the wrong size."
- );
- #endif
-
- const uint8_t grid_max_x = TERN(AUTO_BED_LEVELING_BILINEAR, GRID_MAX_POINTS_X, 3),
- grid_max_y = TERN(AUTO_BED_LEVELING_BILINEAR, GRID_MAX_POINTS_Y, 3);
- EEPROM_WRITE(grid_max_x);
- EEPROM_WRITE(grid_max_y);
- #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
- EEPROM_WRITE(bedlevel.grid_spacing);
- EEPROM_WRITE(bedlevel.grid_start);
- #else
- const xy_pos_t bilinear_grid_spacing{0}, bilinear_start{0};
- EEPROM_WRITE(bilinear_grid_spacing);
- EEPROM_WRITE(bilinear_start);
- #endif
-
- #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
- EEPROM_WRITE(bedlevel.z_values); // 9-256 floats
- #else
- dummyf = 0;
- for (uint16_t q = grid_max_x * grid_max_y; q--;) EEPROM_WRITE(dummyf);
- #endif
- }
-
- //
- // X Axis Twist Compensation
- //
- #if ENABLED(X_AXIS_TWIST_COMPENSATION)
- _FIELD_TEST(xatc_spacing);
- EEPROM_WRITE(xatc.spacing);
- EEPROM_WRITE(xatc.start);
- EEPROM_WRITE(xatc.z_offset);
- #endif
-
- //
- // Unified Bed Leveling
- //
- {
- _FIELD_TEST(planner_leveling_active);
- const bool ubl_active = TERN(AUTO_BED_LEVELING_UBL, planner.leveling_active, false);
- const int8_t storage_slot = TERN(AUTO_BED_LEVELING_UBL, bedlevel.storage_slot, -1);
- EEPROM_WRITE(ubl_active);
- EEPROM_WRITE(storage_slot);
- }
-
- //
- // Servo Angles
- //
- {
- _FIELD_TEST(servo_angles);
- #if !HAS_SERVO_ANGLES
- uint16_t servo_angles[EEPROM_NUM_SERVOS][2] = { { 0, 0 } };
- #endif
- EEPROM_WRITE(servo_angles);
- }
-
- //
- // Thermal first layer compensation values
- //
- #if HAS_PTC
- #if ENABLED(PTC_PROBE)
- EEPROM_WRITE(ptc.z_offsets_probe);
- #endif
- #if ENABLED(PTC_BED)
- EEPROM_WRITE(ptc.z_offsets_bed);
- #endif
- #if ENABLED(PTC_HOTEND)
- EEPROM_WRITE(ptc.z_offsets_hotend);
- #endif
- #else
- // No placeholder data for this feature
- #endif
-
- //
- // BLTOUCH
- //
- {
- _FIELD_TEST(bltouch_od_5v_mode);
- const bool bltouch_od_5v_mode = TERN0(BLTOUCH, bltouch.od_5v_mode);
- EEPROM_WRITE(bltouch_od_5v_mode);
-
- #ifdef BLTOUCH_HS_MODE
- _FIELD_TEST(bltouch_high_speed_mode);
- const bool bltouch_high_speed_mode = TERN0(BLTOUCH, bltouch.high_speed_mode);
- EEPROM_WRITE(bltouch_high_speed_mode);
- #endif
- }
-
- //
- // Kinematic Settings
- //
- #if IS_KINEMATIC
- {
- EEPROM_WRITE(segments_per_second);
- #if ENABLED(DELTA)
- _FIELD_TEST(delta_height);
- EEPROM_WRITE(delta_height); // 1 float
- EEPROM_WRITE(delta_endstop_adj); // 3 floats
- EEPROM_WRITE(delta_radius); // 1 float
- EEPROM_WRITE(delta_diagonal_rod); // 1 float
- EEPROM_WRITE(delta_tower_angle_trim); // 3 floats
- EEPROM_WRITE(delta_diagonal_rod_trim); // 3 floats
- #elif ENABLED(POLARGRAPH)
- _FIELD_TEST(draw_area_min);
- EEPROM_WRITE(draw_area_min); // 2 floats
- EEPROM_WRITE(draw_area_max); // 2 floats
- EEPROM_WRITE(polargraph_max_belt_len); // 1 float
- #endif
- }
- #endif
-
- //
- // Extra Endstops offsets
- //
- #if HAS_EXTRA_ENDSTOPS
- {
- _FIELD_TEST(x2_endstop_adj);
-
- // Write dual endstops in X, Y, Z order. Unused = 0.0
- dummyf = 0;
- EEPROM_WRITE(TERN(X_DUAL_ENDSTOPS, endstops.x2_endstop_adj, dummyf)); // 1 float
- EEPROM_WRITE(TERN(Y_DUAL_ENDSTOPS, endstops.y2_endstop_adj, dummyf)); // 1 float
- EEPROM_WRITE(TERN(Z_MULTI_ENDSTOPS, endstops.z2_endstop_adj, dummyf)); // 1 float
-
- #if ENABLED(Z_MULTI_ENDSTOPS) && NUM_Z_STEPPERS >= 3
- EEPROM_WRITE(endstops.z3_endstop_adj); // 1 float
- #else
- EEPROM_WRITE(dummyf);
- #endif
-
- #if ENABLED(Z_MULTI_ENDSTOPS) && NUM_Z_STEPPERS >= 4
- EEPROM_WRITE(endstops.z4_endstop_adj); // 1 float
- #else
- EEPROM_WRITE(dummyf);
- #endif
- }
- #endif
-
- #if ENABLED(Z_STEPPER_AUTO_ALIGN)
- EEPROM_WRITE(z_stepper_align.xy);
- #if HAS_Z_STEPPER_ALIGN_STEPPER_XY
- EEPROM_WRITE(z_stepper_align.stepper_xy);
- #endif
- #endif
-
- //
- // LCD Preheat settings
- //
- #if HAS_PREHEAT
- _FIELD_TEST(ui_material_preset);
- EEPROM_WRITE(ui.material_preset);
- #endif
-
- //
- // PIDTEMP
- //
- {
- _FIELD_TEST(hotendPID);
- #if DISABLED(PIDTEMP)
- raw_pidcf_t pidcf = { NAN, NAN, NAN, NAN, NAN };
- #endif
- HOTEND_LOOP() {
- #if ENABLED(PIDTEMP)
- const hotend_pid_t &pid = thermalManager.temp_hotend[e].pid;
- raw_pidcf_t pidcf = { pid.p(), pid.i(), pid.d(), pid.c(), pid.f() };
- #endif
- EEPROM_WRITE(pidcf);
- }
-
- _FIELD_TEST(lpq_len);
- const int16_t lpq_len = TERN(PID_EXTRUSION_SCALING, thermalManager.lpq_len, 20);
- EEPROM_WRITE(lpq_len);
- }
-
- //
- // PIDTEMPBED
- //
- {
- _FIELD_TEST(bedPID);
- #if ENABLED(PIDTEMPBED)
- const PID_t &pid = thermalManager.temp_bed.pid;
- const raw_pid_t bed_pid = { pid.p(), pid.i(), pid.d() };
- #else
- const raw_pid_t bed_pid = { NAN, NAN, NAN };
- #endif
- EEPROM_WRITE(bed_pid);
- }
-
- //
- // PIDTEMPCHAMBER
- //
- {
- _FIELD_TEST(chamberPID);
- #if ENABLED(PIDTEMPCHAMBER)
- const PID_t &pid = thermalManager.temp_chamber.pid;
- const raw_pid_t chamber_pid = { pid.p(), pid.i(), pid.d() };
- #else
- const raw_pid_t chamber_pid = { NAN, NAN, NAN };
- #endif
- EEPROM_WRITE(chamber_pid);
- }
-
- //
- // User-defined Thermistors
- //
- #if HAS_USER_THERMISTORS
- _FIELD_TEST(user_thermistor);
- EEPROM_WRITE(thermalManager.user_thermistor);
- #endif
-
- //
- // Power monitor
- //
- {
- #if HAS_POWER_MONITOR
- const uint8_t &power_monitor_flags = power_monitor.flags;
- #else
- constexpr uint8_t power_monitor_flags = 0x00;
- #endif
- _FIELD_TEST(power_monitor_flags);
- EEPROM_WRITE(power_monitor_flags);
- }
-
- //
- // LCD Contrast
- //
- {
- _FIELD_TEST(lcd_contrast);
- const uint8_t lcd_contrast = TERN(HAS_LCD_CONTRAST, ui.contrast, 127);
- EEPROM_WRITE(lcd_contrast);
- }
-
- //
- // LCD Brightness
- //
- {
- _FIELD_TEST(lcd_brightness);
- const uint8_t lcd_brightness = TERN(HAS_LCD_BRIGHTNESS, ui.brightness, 255);
- EEPROM_WRITE(lcd_brightness);
- }
-
- //
- // LCD Backlight / Sleep Timeout
- //
- #if LCD_BACKLIGHT_TIMEOUT_MINS
- EEPROM_WRITE(ui.backlight_timeout_minutes);
- #elif HAS_DISPLAY_SLEEP
- EEPROM_WRITE(ui.sleep_timeout_minutes);
- #endif
-
- //
- // Controller Fan
- //
- {
- _FIELD_TEST(controllerFan_settings);
- #if ENABLED(USE_CONTROLLER_FAN)
- const controllerFan_settings_t &cfs = controllerFan.settings;
- #else
- constexpr controllerFan_settings_t cfs = controllerFan_defaults;
- #endif
- EEPROM_WRITE(cfs);
- }
-
- //
- // Power-Loss Recovery
- //
- {
- _FIELD_TEST(recovery_enabled);
- const bool recovery_enabled = TERN(POWER_LOSS_RECOVERY, recovery.enabled, ENABLED(PLR_ENABLED_DEFAULT));
- EEPROM_WRITE(recovery_enabled);
- }
-
- //
- // Firmware Retraction
- //
- {
- _FIELD_TEST(fwretract_settings);
- #if DISABLED(FWRETRACT)
- const fwretract_settings_t autoretract_defaults = { 3, 45, 0, 0, 0, 13, 0, 8 };
- #endif
- EEPROM_WRITE(TERN(FWRETRACT, fwretract.settings, autoretract_defaults));
-
- #if DISABLED(FWRETRACT_AUTORETRACT)
- const bool autoretract_enabled = false;
- #endif
- EEPROM_WRITE(TERN(FWRETRACT_AUTORETRACT, fwretract.autoretract_enabled, autoretract_enabled));
- }
-
- //
- // Volumetric & Filament Size
- //
- {
- _FIELD_TEST(parser_volumetric_enabled);
-
- #if DISABLED(NO_VOLUMETRICS)
-
- EEPROM_WRITE(parser.volumetric_enabled);
- EEPROM_WRITE(planner.filament_size);
- #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT)
- EEPROM_WRITE(planner.volumetric_extruder_limit);
- #else
- dummyf = DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT;
- for (uint8_t q = EXTRUDERS; q--;) EEPROM_WRITE(dummyf);
- #endif
-
- #else
-
- const bool volumetric_enabled = false;
- EEPROM_WRITE(volumetric_enabled);
- dummyf = DEFAULT_NOMINAL_FILAMENT_DIA;
- for (uint8_t q = EXTRUDERS; q--;) EEPROM_WRITE(dummyf);
- dummyf = DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT;
- for (uint8_t q = EXTRUDERS; q--;) EEPROM_WRITE(dummyf);
-
- #endif
- }
-
- //
- // TMC Configuration
- //
- {
- _FIELD_TEST(tmc_stepper_current);
-
- per_stepper_uint16_t tmc_stepper_current{0};
-
- #if HAS_TRINAMIC_CONFIG
- #if AXIS_IS_TMC(X)
- tmc_stepper_current.X = stepperX.getMilliamps();
- #endif
- #if AXIS_IS_TMC(Y)
- tmc_stepper_current.Y = stepperY.getMilliamps();
- #endif
- #if AXIS_IS_TMC(Z)
- tmc_stepper_current.Z = stepperZ.getMilliamps();
- #endif
- #if AXIS_IS_TMC(I)
- tmc_stepper_current.I = stepperI.getMilliamps();
- #endif
- #if AXIS_IS_TMC(J)
- tmc_stepper_current.J = stepperJ.getMilliamps();
- #endif
- #if AXIS_IS_TMC(K)
- tmc_stepper_current.K = stepperK.getMilliamps();
- #endif
- #if AXIS_IS_TMC(U)
- tmc_stepper_current.U = stepperU.getMilliamps();
- #endif
- #if AXIS_IS_TMC(V)
- tmc_stepper_current.V = stepperV.getMilliamps();
- #endif
- #if AXIS_IS_TMC(W)
- tmc_stepper_current.W = stepperW.getMilliamps();
- #endif
- #if AXIS_IS_TMC(X2)
- tmc_stepper_current.X2 = stepperX2.getMilliamps();
- #endif
- #if AXIS_IS_TMC(Y2)
- tmc_stepper_current.Y2 = stepperY2.getMilliamps();
- #endif
- #if AXIS_IS_TMC(Z2)
- tmc_stepper_current.Z2 = stepperZ2.getMilliamps();
- #endif
- #if AXIS_IS_TMC(Z3)
- tmc_stepper_current.Z3 = stepperZ3.getMilliamps();
- #endif
- #if AXIS_IS_TMC(Z4)
- tmc_stepper_current.Z4 = stepperZ4.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E0)
- tmc_stepper_current.E0 = stepperE0.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E1)
- tmc_stepper_current.E1 = stepperE1.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E2)
- tmc_stepper_current.E2 = stepperE2.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E3)
- tmc_stepper_current.E3 = stepperE3.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E4)
- tmc_stepper_current.E4 = stepperE4.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E5)
- tmc_stepper_current.E5 = stepperE5.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E6)
- tmc_stepper_current.E6 = stepperE6.getMilliamps();
- #endif
- #if AXIS_IS_TMC(E7)
- tmc_stepper_current.E7 = stepperE7.getMilliamps();
- #endif
- #endif
- EEPROM_WRITE(tmc_stepper_current);
- }
-
- //
- // TMC Hybrid Threshold, and placeholder values
- //
- {
- _FIELD_TEST(tmc_hybrid_threshold);
-
- #if ENABLED(HYBRID_THRESHOLD)
- per_stepper_uint32_t tmc_hybrid_threshold{0};
- TERN_(X_HAS_STEALTHCHOP, tmc_hybrid_threshold.X = stepperX.get_pwm_thrs());
- TERN_(Y_HAS_STEALTHCHOP, tmc_hybrid_threshold.Y = stepperY.get_pwm_thrs());
- TERN_(Z_HAS_STEALTHCHOP, tmc_hybrid_threshold.Z = stepperZ.get_pwm_thrs());
- TERN_(I_HAS_STEALTHCHOP, tmc_hybrid_threshold.I = stepperI.get_pwm_thrs());
- TERN_(J_HAS_STEALTHCHOP, tmc_hybrid_threshold.J = stepperJ.get_pwm_thrs());
- TERN_(K_HAS_STEALTHCHOP, tmc_hybrid_threshold.K = stepperK.get_pwm_thrs());
- TERN_(U_HAS_STEALTHCHOP, tmc_hybrid_threshold.U = stepperU.get_pwm_thrs());
- TERN_(V_HAS_STEALTHCHOP, tmc_hybrid_threshold.V = stepperV.get_pwm_thrs());
- TERN_(W_HAS_STEALTHCHOP, tmc_hybrid_threshold.W = stepperW.get_pwm_thrs());
- TERN_(X2_HAS_STEALTHCHOP, tmc_hybrid_threshold.X2 = stepperX2.get_pwm_thrs());
- TERN_(Y2_HAS_STEALTHCHOP, tmc_hybrid_threshold.Y2 = stepperY2.get_pwm_thrs());
- TERN_(Z2_HAS_STEALTHCHOP, tmc_hybrid_threshold.Z2 = stepperZ2.get_pwm_thrs());
- TERN_(Z3_HAS_STEALTHCHOP, tmc_hybrid_threshold.Z3 = stepperZ3.get_pwm_thrs());
- TERN_(Z4_HAS_STEALTHCHOP, tmc_hybrid_threshold.Z4 = stepperZ4.get_pwm_thrs());
- TERN_(E0_HAS_STEALTHCHOP, tmc_hybrid_threshold.E0 = stepperE0.get_pwm_thrs());
- TERN_(E1_HAS_STEALTHCHOP, tmc_hybrid_threshold.E1 = stepperE1.get_pwm_thrs());
- TERN_(E2_HAS_STEALTHCHOP, tmc_hybrid_threshold.E2 = stepperE2.get_pwm_thrs());
- TERN_(E3_HAS_STEALTHCHOP, tmc_hybrid_threshold.E3 = stepperE3.get_pwm_thrs());
- TERN_(E4_HAS_STEALTHCHOP, tmc_hybrid_threshold.E4 = stepperE4.get_pwm_thrs());
- TERN_(E5_HAS_STEALTHCHOP, tmc_hybrid_threshold.E5 = stepperE5.get_pwm_thrs());
- TERN_(E6_HAS_STEALTHCHOP, tmc_hybrid_threshold.E6 = stepperE6.get_pwm_thrs());
- TERN_(E7_HAS_STEALTHCHOP, tmc_hybrid_threshold.E7 = stepperE7.get_pwm_thrs());
- #else
- #define _EN_ITEM(N) , .E##N = 30
- const per_stepper_uint32_t tmc_hybrid_threshold = {
- NUM_AXIS_LIST(.X = 100, .Y = 100, .Z = 3, .I = 3, .J = 3, .K = 3, .U = 3, .V = 3, .W = 3),
- .X2 = 100, .Y2 = 100, .Z2 = 3, .Z3 = 3, .Z4 = 3
- REPEAT(E_STEPPERS, _EN_ITEM)
- };
- #undef _EN_ITEM
- #endif
- EEPROM_WRITE(tmc_hybrid_threshold);
- }
-
- //
- // TMC StallGuard threshold
- //
- {
- mot_stepper_int16_t tmc_sgt{0};
- #if USE_SENSORLESS
- NUM_AXIS_CODE(
- TERN_(X_SENSORLESS, tmc_sgt.X = stepperX.homing_threshold()),
- TERN_(Y_SENSORLESS, tmc_sgt.Y = stepperY.homing_threshold()),
- TERN_(Z_SENSORLESS, tmc_sgt.Z = stepperZ.homing_threshold()),
- TERN_(I_SENSORLESS, tmc_sgt.I = stepperI.homing_threshold()),
- TERN_(J_SENSORLESS, tmc_sgt.J = stepperJ.homing_threshold()),
- TERN_(K_SENSORLESS, tmc_sgt.K = stepperK.homing_threshold()),
- TERN_(U_SENSORLESS, tmc_sgt.U = stepperU.homing_threshold()),
- TERN_(V_SENSORLESS, tmc_sgt.V = stepperV.homing_threshold()),
- TERN_(W_SENSORLESS, tmc_sgt.W = stepperW.homing_threshold())
- );
- TERN_(X2_SENSORLESS, tmc_sgt.X2 = stepperX2.homing_threshold());
- TERN_(Y2_SENSORLESS, tmc_sgt.Y2 = stepperY2.homing_threshold());
- TERN_(Z2_SENSORLESS, tmc_sgt.Z2 = stepperZ2.homing_threshold());
- TERN_(Z3_SENSORLESS, tmc_sgt.Z3 = stepperZ3.homing_threshold());
- TERN_(Z4_SENSORLESS, tmc_sgt.Z4 = stepperZ4.homing_threshold());
- #endif
- EEPROM_WRITE(tmc_sgt);
- }
-
- //
- // TMC stepping mode
- //
- {
- _FIELD_TEST(tmc_stealth_enabled);
-
- per_stepper_bool_t tmc_stealth_enabled = { false };
- TERN_(X_HAS_STEALTHCHOP, tmc_stealth_enabled.X = stepperX.get_stored_stealthChop());
- TERN_(Y_HAS_STEALTHCHOP, tmc_stealth_enabled.Y = stepperY.get_stored_stealthChop());
- TERN_(Z_HAS_STEALTHCHOP, tmc_stealth_enabled.Z = stepperZ.get_stored_stealthChop());
- TERN_(I_HAS_STEALTHCHOP, tmc_stealth_enabled.I = stepperI.get_stored_stealthChop());
- TERN_(J_HAS_STEALTHCHOP, tmc_stealth_enabled.J = stepperJ.get_stored_stealthChop());
- TERN_(K_HAS_STEALTHCHOP, tmc_stealth_enabled.K = stepperK.get_stored_stealthChop());
- TERN_(U_HAS_STEALTHCHOP, tmc_stealth_enabled.U = stepperU.get_stored_stealthChop());
- TERN_(V_HAS_STEALTHCHOP, tmc_stealth_enabled.V = stepperV.get_stored_stealthChop());
- TERN_(W_HAS_STEALTHCHOP, tmc_stealth_enabled.W = stepperW.get_stored_stealthChop());
- TERN_(X2_HAS_STEALTHCHOP, tmc_stealth_enabled.X2 = stepperX2.get_stored_stealthChop());
- TERN_(Y2_HAS_STEALTHCHOP, tmc_stealth_enabled.Y2 = stepperY2.get_stored_stealthChop());
- TERN_(Z2_HAS_STEALTHCHOP, tmc_stealth_enabled.Z2 = stepperZ2.get_stored_stealthChop());
- TERN_(Z3_HAS_STEALTHCHOP, tmc_stealth_enabled.Z3 = stepperZ3.get_stored_stealthChop());
- TERN_(Z4_HAS_STEALTHCHOP, tmc_stealth_enabled.Z4 = stepperZ4.get_stored_stealthChop());
- TERN_(E0_HAS_STEALTHCHOP, tmc_stealth_enabled.E0 = stepperE0.get_stored_stealthChop());
- TERN_(E1_HAS_STEALTHCHOP, tmc_stealth_enabled.E1 = stepperE1.get_stored_stealthChop());
- TERN_(E2_HAS_STEALTHCHOP, tmc_stealth_enabled.E2 = stepperE2.get_stored_stealthChop());
- TERN_(E3_HAS_STEALTHCHOP, tmc_stealth_enabled.E3 = stepperE3.get_stored_stealthChop());
- TERN_(E4_HAS_STEALTHCHOP, tmc_stealth_enabled.E4 = stepperE4.get_stored_stealthChop());
- TERN_(E5_HAS_STEALTHCHOP, tmc_stealth_enabled.E5 = stepperE5.get_stored_stealthChop());
- TERN_(E6_HAS_STEALTHCHOP, tmc_stealth_enabled.E6 = stepperE6.get_stored_stealthChop());
- TERN_(E7_HAS_STEALTHCHOP, tmc_stealth_enabled.E7 = stepperE7.get_stored_stealthChop());
- EEPROM_WRITE(tmc_stealth_enabled);
- }
-
- //
- // Linear Advance
- //
- {
- _FIELD_TEST(planner_extruder_advance_K);
-
- #if ENABLED(LIN_ADVANCE)
- EEPROM_WRITE(planner.extruder_advance_K);
- #else
- dummyf = 0;
- for (uint8_t q = _MAX(EXTRUDERS, 1); q--;) EEPROM_WRITE(dummyf);
- #endif
- }
-
- //
- // Motor Current PWM
- //
- {
- _FIELD_TEST(motor_current_setting);
-
- #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM
- EEPROM_WRITE(stepper.motor_current_setting);
- #else
- const uint32_t no_current[MOTOR_CURRENT_COUNT] = { 0 };
- EEPROM_WRITE(no_current);
- #endif
- }
-
- //
- // CNC Coordinate Systems
- //
-
- _FIELD_TEST(coordinate_system);
-
- #if DISABLED(CNC_COORDINATE_SYSTEMS)
- const xyz_pos_t coordinate_system[MAX_COORDINATE_SYSTEMS] = { { 0 } };
- #endif
- EEPROM_WRITE(TERN(CNC_COORDINATE_SYSTEMS, gcode.coordinate_system, coordinate_system));
-
- //
- // Skew correction factors
- //
- _FIELD_TEST(planner_skew_factor);
- EEPROM_WRITE(planner.skew_factor);
-
- //
- // POLARGRAPH
- //
- #if ENABLED(POLARGRAPH)
- _FIELD_TEST(polargraph_max_belt_len);
- EEPROM_WRITE(polargraph_max_belt_len);
- #endif
-
- //
- // Advanced Pause filament load & unload lengths
- //
- #if HAS_EXTRUDERS
- {
- #if DISABLED(ADVANCED_PAUSE_FEATURE)
- const fil_change_settings_t fc_settings[EXTRUDERS] = { 0, 0 };
- #endif
- _FIELD_TEST(fc_settings);
- EEPROM_WRITE(fc_settings);
- }
- #endif
-
- //
- // Multiple Extruders
- //
-
- #if HAS_MULTI_EXTRUDER
- _FIELD_TEST(toolchange_settings);
- EEPROM_WRITE(toolchange_settings);
- #endif
-
- //
- // Backlash Compensation
- //
- {
- #if ENABLED(BACKLASH_GCODE)
- xyz_float_t backlash_distance_mm;
- LOOP_NUM_AXES(axis) backlash_distance_mm[axis] = backlash.get_distance_mm((AxisEnum)axis);
- const uint8_t backlash_correction = backlash.get_correction_uint8();
- #else
- const xyz_float_t backlash_distance_mm{0};
- const uint8_t backlash_correction = 0;
- #endif
- #if ENABLED(BACKLASH_GCODE) && defined(BACKLASH_SMOOTHING_MM)
- const float backlash_smoothing_mm = backlash.get_smoothing_mm();
- #else
- const float backlash_smoothing_mm = 3;
- #endif
- _FIELD_TEST(backlash_distance_mm);
- EEPROM_WRITE(backlash_distance_mm);
- EEPROM_WRITE(backlash_correction);
- EEPROM_WRITE(backlash_smoothing_mm);
- }
-
- //
- // Extensible UI User Data
- //
- #if ENABLED(EXTENSIBLE_UI)
- {
- char extui_data[ExtUI::eeprom_data_size] = { 0 };
- ExtUI::onStoreSettings(extui_data);
- _FIELD_TEST(extui_data);
- EEPROM_WRITE(extui_data);
- }
- #endif
-
- //
- // Creality DWIN User Data
- //
- #if ENABLED(DWIN_LCD_PROUI)
- {
- _FIELD_TEST(dwin_data);
- char dwin_data[eeprom_data_size] = { 0 };
- DWIN_CopySettingsTo(dwin_data);
- EEPROM_WRITE(dwin_data);
- }
- #endif
-
- #if ENABLED(DWIN_CREALITY_LCD_JYERSUI)
- {
- _FIELD_TEST(dwin_settings);
- char dwin_settings[CrealityDWIN.eeprom_data_size] = { 0 };
- CrealityDWIN.Save_Settings(dwin_settings);
- EEPROM_WRITE(dwin_settings);
- }
- #endif
-
- //
- // Case Light Brightness
- //
- #if CASELIGHT_USES_BRIGHTNESS
- EEPROM_WRITE(caselight.brightness);
- #endif
-
- //
- // Password feature
- //
- #if ENABLED(PASSWORD_FEATURE)
- EEPROM_WRITE(password.is_set);
- EEPROM_WRITE(password.value);
- #endif
-
- //
- // TOUCH_SCREEN_CALIBRATION
- //
- #if ENABLED(TOUCH_SCREEN_CALIBRATION)
- EEPROM_WRITE(touch_calibration.calibration);
- #endif
-
- //
- // Ethernet network info
- //
- #if HAS_ETHERNET
- {
- _FIELD_TEST(ethernet_hardware_enabled);
- const bool ethernet_hardware_enabled = ethernet.hardware_enabled;
- const uint32_t ethernet_ip = ethernet.ip,
- ethernet_dns = ethernet.myDns,
- ethernet_gateway = ethernet.gateway,
- ethernet_subnet = ethernet.subnet;
- EEPROM_WRITE(ethernet_hardware_enabled);
- EEPROM_WRITE(ethernet_ip);
- EEPROM_WRITE(ethernet_dns);
- EEPROM_WRITE(ethernet_gateway);
- EEPROM_WRITE(ethernet_subnet);
- }
- #endif
-
- //
- // Buzzer enable/disable
- //
- #if ENABLED(SOUND_MENU_ITEM)
- EEPROM_WRITE(ui.sound_on);
- #endif
-
- //
- // Fan tachometer check
- //
- #if HAS_FANCHECK
- EEPROM_WRITE(fan_check.enabled);
- #endif
-
- //
- // MKS UI controller
- //
- #if ENABLED(DGUS_LCD_UI_MKS)
- EEPROM_WRITE(mks_language_index);
- EEPROM_WRITE(mks_corner_offsets);
- EEPROM_WRITE(mks_park_pos);
- EEPROM_WRITE(mks_min_extrusion_temp);
- #endif
-
- //
- // Selected LCD language
- //
- #if HAS_MULTI_LANGUAGE
- EEPROM_WRITE(ui.language);
- #endif
-
- //
- // Model predictive control
- //
- #if ENABLED(MPCTEMP)
- HOTEND_LOOP()
- EEPROM_WRITE(thermalManager.temp_hotend[e].constants);
- #endif
-
- //
- // Report final CRC and Data Size
- //
- if (!eeprom_error) {
- const uint16_t eeprom_size = eeprom_index - (EEPROM_OFFSET),
- final_crc = working_crc;
-
- // Write the EEPROM header
- eeprom_index = EEPROM_OFFSET;
-
- EEPROM_WRITE(version);
- #if ENABLED(EEPROM_INIT_NOW)
- EEPROM_WRITE(build_hash);
- #endif
- EEPROM_WRITE(final_crc);
-
- // Report storage size
- DEBUG_ECHO_MSG("Settings Stored (", eeprom_size, " bytes; crc ", (uint32_t)final_crc, ")");
-
- eeprom_error |= size_error(eeprom_size);
- }
- EEPROM_FINISH();
-
- //
- // UBL Mesh
- //
- #if ENABLED(UBL_SAVE_ACTIVE_ON_M500)
- if (bedlevel.storage_slot >= 0)
- store_mesh(bedlevel.storage_slot);
- #endif
-
- if (!eeprom_error) {
- LCD_MESSAGE(MSG_SETTINGS_STORED);
- TERN_(HOST_PROMPT_SUPPORT, hostui.notify(GET_TEXT_F(MSG_SETTINGS_STORED)));
- }
-
- TERN_(EXTENSIBLE_UI, ExtUI::onSettingsStored(!eeprom_error));
-
- return !eeprom_error;
- }
-
- /**
- * M501 - Retrieve Configuration
- */
- bool MarlinSettings::_load() {
- if (!EEPROM_START(EEPROM_OFFSET)) return false;
-
- char stored_ver[4];
- EEPROM_READ_ALWAYS(stored_ver);
-
- // Version has to match or defaults are used
- if (strncmp(version, stored_ver, 3) != 0) {
- if (stored_ver[3] != '\0') {
- stored_ver[0] = '?';
- stored_ver[1] = '\0';
- }
- DEBUG_ECHO_MSG("EEPROM version mismatch (EEPROM=", stored_ver, " Marlin=" EEPROM_VERSION ")");
- TERN_(DWIN_LCD_PROUI, LCD_MESSAGE(MSG_ERR_EEPROM_VERSION));
- TERN_(HOST_PROMPT_SUPPORT, hostui.notify(GET_TEXT_F(MSG_ERR_EEPROM_VERSION)));
-
- IF_DISABLED(EEPROM_AUTO_INIT, ui.eeprom_alert_version());
- eeprom_error = true;
- }
- else {
-
- // Optionally reset on the first boot after flashing
- #if ENABLED(EEPROM_INIT_NOW)
- uint32_t stored_hash;
- EEPROM_READ_ALWAYS(stored_hash);
- if (stored_hash != build_hash) { EEPROM_FINISH(); return false; }
- #endif
-
- uint16_t stored_crc;
- EEPROM_READ_ALWAYS(stored_crc);
-
- float dummyf = 0;
- working_crc = 0; // Init to 0. Accumulated by EEPROM_READ
-
- _FIELD_TEST(e_factors);
-
- // Number of e_factors may change
- uint8_t e_factors;
- EEPROM_READ_ALWAYS(e_factors);
-
- //
- // Planner Motion
- //
- {
- // Get only the number of E stepper parameters previously stored
- // Any steppers added later are set to their defaults
- uint32_t tmp1[NUM_AXES + e_factors];
- float tmp2[NUM_AXES + e_factors];
- feedRate_t tmp3[NUM_AXES + e_factors];
- EEPROM_READ((uint8_t *)tmp1, sizeof(tmp1)); // max_acceleration_mm_per_s2
- EEPROM_READ(planner.settings.min_segment_time_us);
- EEPROM_READ((uint8_t *)tmp2, sizeof(tmp2)); // axis_steps_per_mm
- EEPROM_READ((uint8_t *)tmp3, sizeof(tmp3)); // max_feedrate_mm_s
-
- if (!validating) LOOP_DISTINCT_AXES(i) {
- const bool in = (i < e_factors + NUM_AXES);
- planner.settings.max_acceleration_mm_per_s2[i] = in ? tmp1[i] : pgm_read_dword(&_DMA[ALIM(i, _DMA)]);
- planner.settings.axis_steps_per_mm[i] = in ? tmp2[i] : pgm_read_float(&_DASU[ALIM(i, _DASU)]);
- planner.settings.max_feedrate_mm_s[i] = in ? tmp3[i] : pgm_read_float(&_DMF[ALIM(i, _DMF)]);
- }
-
- EEPROM_READ(planner.settings.acceleration);
- EEPROM_READ(planner.settings.retract_acceleration);
- EEPROM_READ(planner.settings.travel_acceleration);
- EEPROM_READ(planner.settings.min_feedrate_mm_s);
- EEPROM_READ(planner.settings.min_travel_feedrate_mm_s);
-
- #if HAS_CLASSIC_JERK
- EEPROM_READ(planner.max_jerk);
- #if HAS_LINEAR_E_JERK
- EEPROM_READ(dummyf);
- #endif
- #else
- for (uint8_t q = LOGICAL_AXES; q--;) EEPROM_READ(dummyf);
- #endif
-
- EEPROM_READ(TERN(CLASSIC_JERK, dummyf, planner.junction_deviation_mm));
- }
-
- //
- // Home Offset (M206 / M665)
- //
- {
- _FIELD_TEST(home_offset);
-
- #if HAS_SCARA_OFFSET
- EEPROM_READ(scara_home_offset);
- #else
- #if !HAS_HOME_OFFSET
- xyz_pos_t home_offset;
- #endif
- EEPROM_READ(home_offset);
- #endif
- }
-
- //
- // Hotend Offsets, if any
- //
- {
- #if HAS_HOTEND_OFFSET
- // Skip hotend 0 which must be 0
- LOOP_S_L_N(e, 1, HOTENDS)
- EEPROM_READ(hotend_offset[e]);
- #endif
- }
-
- //
- // Filament Runout Sensor
- //
- {
- int8_t runout_sensor_enabled;
- _FIELD_TEST(runout_sensor_enabled);
- EEPROM_READ(runout_sensor_enabled);
- #if HAS_FILAMENT_SENSOR
- runout.enabled = runout_sensor_enabled < 0 ? FIL_RUNOUT_ENABLED_DEFAULT : runout_sensor_enabled;
- #endif
-
- TERN_(HAS_FILAMENT_SENSOR, if (runout.enabled) runout.reset());
-
- float runout_distance_mm;
- EEPROM_READ(runout_distance_mm);
- #if HAS_FILAMENT_RUNOUT_DISTANCE
- if (!validating) runout.set_runout_distance(runout_distance_mm);
- #endif
- }
-
- //
- // Global Leveling
- //
- EEPROM_READ(TERN(ENABLE_LEVELING_FADE_HEIGHT, new_z_fade_height, dummyf));
-
- //
- // Mesh (Manual) Bed Leveling
- //
- {
- uint8_t mesh_num_x, mesh_num_y;
- EEPROM_READ(dummyf);
- EEPROM_READ_ALWAYS(mesh_num_x);
- EEPROM_READ_ALWAYS(mesh_num_y);
-
- #if ENABLED(MESH_BED_LEVELING)
- if (!validating) bedlevel.z_offset = dummyf;
- if (mesh_num_x == (GRID_MAX_POINTS_X) && mesh_num_y == (GRID_MAX_POINTS_Y)) {
- // EEPROM data fits the current mesh
- EEPROM_READ(bedlevel.z_values);
- }
- else {
- // EEPROM data is stale
- if (!validating) bedlevel.reset();
- for (uint16_t q = mesh_num_x * mesh_num_y; q--;) EEPROM_READ(dummyf);
- }
- #else
- // MBL is disabled - skip the stored data
- for (uint16_t q = mesh_num_x * mesh_num_y; q--;) EEPROM_READ(dummyf);
- #endif
- }
-
- //
- // Probe Z Offset
- //
- {
- _FIELD_TEST(probe_offset);
- #if HAS_BED_PROBE
- const xyz_pos_t &zpo = probe.offset;
- #else
- xyz_pos_t zpo;
- #endif
- EEPROM_READ(zpo);
- }
-
- //
- // Planar Bed Leveling matrix
- //
- {
- #if ABL_PLANAR
- EEPROM_READ(planner.bed_level_matrix);
- #else
- for (uint8_t q = 9; q--;) EEPROM_READ(dummyf);
- #endif
- }
-
- //
- // Bilinear Auto Bed Leveling
- //
- {
- uint8_t grid_max_x, grid_max_y;
- EEPROM_READ_ALWAYS(grid_max_x); // 1 byte
- EEPROM_READ_ALWAYS(grid_max_y); // 1 byte
- xy_pos_t spacing, start;
- EEPROM_READ(spacing); // 2 ints
- EEPROM_READ(start); // 2 ints
- #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
- if (grid_max_x == (GRID_MAX_POINTS_X) && grid_max_y == (GRID_MAX_POINTS_Y)) {
- if (!validating) set_bed_leveling_enabled(false);
- bedlevel.set_grid(spacing, start);
- EEPROM_READ(bedlevel.z_values); // 9 to 256 floats
- }
- else // EEPROM data is stale
- #endif // AUTO_BED_LEVELING_BILINEAR
- {
- // Skip past disabled (or stale) Bilinear Grid data
- for (uint16_t q = grid_max_x * grid_max_y; q--;) EEPROM_READ(dummyf);
- }
- }
-
- //
- // X Axis Twist Compensation
- //
- #if ENABLED(X_AXIS_TWIST_COMPENSATION)
- _FIELD_TEST(xatc_spacing);
- EEPROM_READ(xatc.spacing);
- EEPROM_READ(xatc.start);
- EEPROM_READ(xatc.z_offset);
- #endif
-
- //
- // Unified Bed Leveling active state
- //
- {
- _FIELD_TEST(planner_leveling_active);
- #if ENABLED(AUTO_BED_LEVELING_UBL)
- const bool &planner_leveling_active = planner.leveling_active;
- const int8_t &ubl_storage_slot = bedlevel.storage_slot;
- #else
- bool planner_leveling_active;
- int8_t ubl_storage_slot;
- #endif
- EEPROM_READ(planner_leveling_active);
- EEPROM_READ(ubl_storage_slot);
- }
-
- //
- // SERVO_ANGLES
- //
- {
- _FIELD_TEST(servo_angles);
- #if ENABLED(EDITABLE_SERVO_ANGLES)
- uint16_t (&servo_angles_arr)[EEPROM_NUM_SERVOS][2] = servo_angles;
- #else
- uint16_t servo_angles_arr[EEPROM_NUM_SERVOS][2];
- #endif
- EEPROM_READ(servo_angles_arr);
- }
-
- //
- // Thermal first layer compensation values
- //
- #if HAS_PTC
- #if ENABLED(PTC_PROBE)
- EEPROM_READ(ptc.z_offsets_probe);
- #endif
- # if ENABLED(PTC_BED)
- EEPROM_READ(ptc.z_offsets_bed);
- #endif
- #if ENABLED(PTC_HOTEND)
- EEPROM_READ(ptc.z_offsets_hotend);
- #endif
- ptc.reset_index();
- #else
- // No placeholder data for this feature
- #endif
-
- //
- // BLTOUCH
- //
- {
- _FIELD_TEST(bltouch_od_5v_mode);
- #if ENABLED(BLTOUCH)
- const bool &bltouch_od_5v_mode = bltouch.od_5v_mode;
- #else
- bool bltouch_od_5v_mode;
- #endif
- EEPROM_READ(bltouch_od_5v_mode);
-
- #ifdef BLTOUCH_HS_MODE
- _FIELD_TEST(bltouch_high_speed_mode);
- #if ENABLED(BLTOUCH)
- const bool &bltouch_high_speed_mode = bltouch.high_speed_mode;
- #else
- bool bltouch_high_speed_mode;
- #endif
- EEPROM_READ(bltouch_high_speed_mode);
- #endif
- }
-
- //
- // Kinematic Segments-per-second
- //
- #if IS_KINEMATIC
- {
- EEPROM_READ(segments_per_second);
- #if ENABLED(DELTA)
- _FIELD_TEST(delta_height);
- EEPROM_READ(delta_height); // 1 float
- EEPROM_READ(delta_endstop_adj); // 3 floats
- EEPROM_READ(delta_radius); // 1 float
- EEPROM_READ(delta_diagonal_rod); // 1 float
- EEPROM_READ(delta_tower_angle_trim); // 3 floats
- EEPROM_READ(delta_diagonal_rod_trim); // 3 floats
- #elif ENABLED(POLARGRAPH)
- _FIELD_TEST(draw_area_min);
- EEPROM_READ(draw_area_min); // 2 floats
- EEPROM_READ(draw_area_max); // 2 floats
- EEPROM_READ(polargraph_max_belt_len); // 1 float
- #endif
- }
- #endif
-
- //
- // Extra Endstops offsets
- //
- #if HAS_EXTRA_ENDSTOPS
- {
- _FIELD_TEST(x2_endstop_adj);
-
- EEPROM_READ(TERN(X_DUAL_ENDSTOPS, endstops.x2_endstop_adj, dummyf)); // 1 float
- EEPROM_READ(TERN(Y_DUAL_ENDSTOPS, endstops.y2_endstop_adj, dummyf)); // 1 float
- EEPROM_READ(TERN(Z_MULTI_ENDSTOPS, endstops.z2_endstop_adj, dummyf)); // 1 float
-
- #if ENABLED(Z_MULTI_ENDSTOPS) && NUM_Z_STEPPERS >= 3
- EEPROM_READ(endstops.z3_endstop_adj); // 1 float
- #else
- EEPROM_READ(dummyf);
- #endif
- #if ENABLED(Z_MULTI_ENDSTOPS) && NUM_Z_STEPPERS >= 4
- EEPROM_READ(endstops.z4_endstop_adj); // 1 float
- #else
- EEPROM_READ(dummyf);
- #endif
- }
- #endif
-
- #if ENABLED(Z_STEPPER_AUTO_ALIGN)
- EEPROM_READ(z_stepper_align.xy);
- #if HAS_Z_STEPPER_ALIGN_STEPPER_XY
- EEPROM_READ(z_stepper_align.stepper_xy);
- #endif
- #endif
-
- //
- // LCD Preheat settings
- //
- #if HAS_PREHEAT
- _FIELD_TEST(ui_material_preset);
- EEPROM_READ(ui.material_preset);
- #endif
-
- //
- // Hotend PID
- //
- {
- HOTEND_LOOP() {
- raw_pidcf_t pidcf;
- EEPROM_READ(pidcf);
- #if ENABLED(PIDTEMP)
- if (!validating && !isnan(pidcf.p))
- thermalManager.temp_hotend[e].pid.set(pidcf);
- #endif
- }
- }
-
- //
- // PID Extrusion Scaling
- //
- {
- _FIELD_TEST(lpq_len);
- #if ENABLED(PID_EXTRUSION_SCALING)
- const int16_t &lpq_len = thermalManager.lpq_len;
- #else
- int16_t lpq_len;
- #endif
- EEPROM_READ(lpq_len);
- }
-
- //
- // Heated Bed PID
- //
- {
- raw_pid_t pid;
- EEPROM_READ(pid);
- #if ENABLED(PIDTEMPBED)
- if (!validating && !isnan(pid.p))
- thermalManager.temp_bed.pid.set(pid);
- #endif
- }
-
- //
- // Heated Chamber PID
- //
- {
- raw_pid_t pid;
- EEPROM_READ(pid);
- #if ENABLED(PIDTEMPCHAMBER)
- if (!validating && !isnan(pid.p))
- thermalManager.temp_chamber.pid.set(pid);
- #endif
- }
-
- //
- // User-defined Thermistors
- //
- #if HAS_USER_THERMISTORS
- {
- user_thermistor_t user_thermistor[USER_THERMISTORS];
- _FIELD_TEST(user_thermistor);
- EEPROM_READ(user_thermistor);
- if (!validating) COPY(thermalManager.user_thermistor, user_thermistor);
- }
- #endif
-
- //
- // Power monitor
- //
- {
- uint8_t power_monitor_flags;
- _FIELD_TEST(power_monitor_flags);
- EEPROM_READ(power_monitor_flags);
- TERN_(HAS_POWER_MONITOR, if (!validating) power_monitor.flags = power_monitor_flags);
- }
-
- //
- // LCD Contrast
- //
- {
- uint8_t lcd_contrast;
- _FIELD_TEST(lcd_contrast);
- EEPROM_READ(lcd_contrast);
- TERN_(HAS_LCD_CONTRAST, if (!validating) ui.contrast = lcd_contrast);
- }
-
- //
- // LCD Brightness
- //
- {
- uint8_t lcd_brightness;
- _FIELD_TEST(lcd_brightness);
- EEPROM_READ(lcd_brightness);
- TERN_(HAS_LCD_BRIGHTNESS, if (!validating) ui.brightness = lcd_brightness);
- }
-
- //
- // LCD Backlight / Sleep Timeout
- //
- #if LCD_BACKLIGHT_TIMEOUT_MINS
- EEPROM_READ(ui.backlight_timeout_minutes);
- #elif HAS_DISPLAY_SLEEP
- EEPROM_READ(ui.sleep_timeout_minutes);
- #endif
-
- //
- // Controller Fan
- //
- {
- controllerFan_settings_t cfs = { 0 };
- _FIELD_TEST(controllerFan_settings);
- EEPROM_READ(cfs);
- TERN_(CONTROLLER_FAN_EDITABLE, if (!validating) controllerFan.settings = cfs);
- }
-
- //
- // Power-Loss Recovery
- //
- {
- bool recovery_enabled;
- _FIELD_TEST(recovery_enabled);
- EEPROM_READ(recovery_enabled);
- TERN_(POWER_LOSS_RECOVERY, if (!validating) recovery.enabled = recovery_enabled);
- }
-
- //
- // Firmware Retraction
- //
- {
- fwretract_settings_t fwretract_settings;
- bool autoretract_enabled;
- _FIELD_TEST(fwretract_settings);
- EEPROM_READ(fwretract_settings);
- EEPROM_READ(autoretract_enabled);
-
- #if ENABLED(FWRETRACT)
- if (!validating) {
- fwretract.settings = fwretract_settings;
- TERN_(FWRETRACT_AUTORETRACT, fwretract.autoretract_enabled = autoretract_enabled);
- }
- #endif
- }
-
- //
- // Volumetric & Filament Size
- //
- {
- struct {
- bool volumetric_enabled;
- float filament_size[EXTRUDERS];
- float volumetric_extruder_limit[EXTRUDERS];
- } storage;
-
- _FIELD_TEST(parser_volumetric_enabled);
- EEPROM_READ(storage);
-
- #if DISABLED(NO_VOLUMETRICS)
- if (!validating) {
- parser.volumetric_enabled = storage.volumetric_enabled;
- COPY(planner.filament_size, storage.filament_size);
- #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT)
- COPY(planner.volumetric_extruder_limit, storage.volumetric_extruder_limit);
- #endif
- }
- #endif
- }
-
- //
- // TMC Stepper Settings
- //
-
- if (!validating) reset_stepper_drivers();
-
- // TMC Stepper Current
- {
- _FIELD_TEST(tmc_stepper_current);
-
- per_stepper_uint16_t currents;
- EEPROM_READ(currents);
-
- #if HAS_TRINAMIC_CONFIG
-
- #define SET_CURR(Q) stepper##Q.rms_current(currents.Q ? currents.Q : Q##_CURRENT)
- if (!validating) {
- #if AXIS_IS_TMC(X)
- SET_CURR(X);
- #endif
- #if AXIS_IS_TMC(Y)
- SET_CURR(Y);
- #endif
- #if AXIS_IS_TMC(Z)
- SET_CURR(Z);
- #endif
- #if AXIS_IS_TMC(X2)
- SET_CURR(X2);
- #endif
- #if AXIS_IS_TMC(Y2)
- SET_CURR(Y2);
- #endif
- #if AXIS_IS_TMC(Z2)
- SET_CURR(Z2);
- #endif
- #if AXIS_IS_TMC(Z3)
- SET_CURR(Z3);
- #endif
- #if AXIS_IS_TMC(Z4)
- SET_CURR(Z4);
- #endif
- #if AXIS_IS_TMC(I)
- SET_CURR(I);
- #endif
- #if AXIS_IS_TMC(J)
- SET_CURR(J);
- #endif
- #if AXIS_IS_TMC(K)
- SET_CURR(K);
- #endif
- #if AXIS_IS_TMC(U)
- SET_CURR(U);
- #endif
- #if AXIS_IS_TMC(V)
- SET_CURR(V);
- #endif
- #if AXIS_IS_TMC(W)
- SET_CURR(W);
- #endif
- #if AXIS_IS_TMC(E0)
- SET_CURR(E0);
- #endif
- #if AXIS_IS_TMC(E1)
- SET_CURR(E1);
- #endif
- #if AXIS_IS_TMC(E2)
- SET_CURR(E2);
- #endif
- #if AXIS_IS_TMC(E3)
- SET_CURR(E3);
- #endif
- #if AXIS_IS_TMC(E4)
- SET_CURR(E4);
- #endif
- #if AXIS_IS_TMC(E5)
- SET_CURR(E5);
- #endif
- #if AXIS_IS_TMC(E6)
- SET_CURR(E6);
- #endif
- #if AXIS_IS_TMC(E7)
- SET_CURR(E7);
- #endif
- }
- #endif
- }
-
- // TMC Hybrid Threshold
- {
- per_stepper_uint32_t tmc_hybrid_threshold;
- _FIELD_TEST(tmc_hybrid_threshold);
- EEPROM_READ(tmc_hybrid_threshold);
-
- #if ENABLED(HYBRID_THRESHOLD)
- if (!validating) {
- TERN_(X_HAS_STEALTHCHOP, stepperX.set_pwm_thrs(tmc_hybrid_threshold.X));
- TERN_(Y_HAS_STEALTHCHOP, stepperY.set_pwm_thrs(tmc_hybrid_threshold.Y));
- TERN_(Z_HAS_STEALTHCHOP, stepperZ.set_pwm_thrs(tmc_hybrid_threshold.Z));
- TERN_(X2_HAS_STEALTHCHOP, stepperX2.set_pwm_thrs(tmc_hybrid_threshold.X2));
- TERN_(Y2_HAS_STEALTHCHOP, stepperY2.set_pwm_thrs(tmc_hybrid_threshold.Y2));
- TERN_(Z2_HAS_STEALTHCHOP, stepperZ2.set_pwm_thrs(tmc_hybrid_threshold.Z2));
- TERN_(Z3_HAS_STEALTHCHOP, stepperZ3.set_pwm_thrs(tmc_hybrid_threshold.Z3));
- TERN_(Z4_HAS_STEALTHCHOP, stepperZ4.set_pwm_thrs(tmc_hybrid_threshold.Z4));
- TERN_(I_HAS_STEALTHCHOP, stepperI.set_pwm_thrs(tmc_hybrid_threshold.I));
- TERN_(J_HAS_STEALTHCHOP, stepperJ.set_pwm_thrs(tmc_hybrid_threshold.J));
- TERN_(K_HAS_STEALTHCHOP, stepperK.set_pwm_thrs(tmc_hybrid_threshold.K));
- TERN_(U_HAS_STEALTHCHOP, stepperU.set_pwm_thrs(tmc_hybrid_threshold.U));
- TERN_(V_HAS_STEALTHCHOP, stepperV.set_pwm_thrs(tmc_hybrid_threshold.V));
- TERN_(W_HAS_STEALTHCHOP, stepperW.set_pwm_thrs(tmc_hybrid_threshold.W));
- TERN_(E0_HAS_STEALTHCHOP, stepperE0.set_pwm_thrs(tmc_hybrid_threshold.E0));
- TERN_(E1_HAS_STEALTHCHOP, stepperE1.set_pwm_thrs(tmc_hybrid_threshold.E1));
- TERN_(E2_HAS_STEALTHCHOP, stepperE2.set_pwm_thrs(tmc_hybrid_threshold.E2));
- TERN_(E3_HAS_STEALTHCHOP, stepperE3.set_pwm_thrs(tmc_hybrid_threshold.E3));
- TERN_(E4_HAS_STEALTHCHOP, stepperE4.set_pwm_thrs(tmc_hybrid_threshold.E4));
- TERN_(E5_HAS_STEALTHCHOP, stepperE5.set_pwm_thrs(tmc_hybrid_threshold.E5));
- TERN_(E6_HAS_STEALTHCHOP, stepperE6.set_pwm_thrs(tmc_hybrid_threshold.E6));
- TERN_(E7_HAS_STEALTHCHOP, stepperE7.set_pwm_thrs(tmc_hybrid_threshold.E7));
- }
- #endif
- }
-
- //
- // TMC StallGuard threshold.
- //
- {
- mot_stepper_int16_t tmc_sgt;
- _FIELD_TEST(tmc_sgt);
- EEPROM_READ(tmc_sgt);
- #if USE_SENSORLESS
- if (!validating) {
- NUM_AXIS_CODE(
- TERN_(X_SENSORLESS, stepperX.homing_threshold(tmc_sgt.X)),
- TERN_(Y_SENSORLESS, stepperY.homing_threshold(tmc_sgt.Y)),
- TERN_(Z_SENSORLESS, stepperZ.homing_threshold(tmc_sgt.Z)),
- TERN_(I_SENSORLESS, stepperI.homing_threshold(tmc_sgt.I)),
- TERN_(J_SENSORLESS, stepperJ.homing_threshold(tmc_sgt.J)),
- TERN_(K_SENSORLESS, stepperK.homing_threshold(tmc_sgt.K)),
- TERN_(U_SENSORLESS, stepperU.homing_threshold(tmc_sgt.U)),
- TERN_(V_SENSORLESS, stepperV.homing_threshold(tmc_sgt.V)),
- TERN_(W_SENSORLESS, stepperW.homing_threshold(tmc_sgt.W))
- );
- TERN_(X2_SENSORLESS, stepperX2.homing_threshold(tmc_sgt.X2));
- TERN_(Y2_SENSORLESS, stepperY2.homing_threshold(tmc_sgt.Y2));
- TERN_(Z2_SENSORLESS, stepperZ2.homing_threshold(tmc_sgt.Z2));
- TERN_(Z3_SENSORLESS, stepperZ3.homing_threshold(tmc_sgt.Z3));
- TERN_(Z4_SENSORLESS, stepperZ4.homing_threshold(tmc_sgt.Z4));
- }
- #endif
- }
-
- // TMC stepping mode
- {
- _FIELD_TEST(tmc_stealth_enabled);
-
- per_stepper_bool_t tmc_stealth_enabled;
- EEPROM_READ(tmc_stealth_enabled);
-
- #if HAS_TRINAMIC_CONFIG
-
- #define SET_STEPPING_MODE(ST) stepper##ST.stored.stealthChop_enabled = tmc_stealth_enabled.ST; stepper##ST.refresh_stepping_mode();
- if (!validating) {
- TERN_(X_HAS_STEALTHCHOP, SET_STEPPING_MODE(X));
- TERN_(Y_HAS_STEALTHCHOP, SET_STEPPING_MODE(Y));
- TERN_(Z_HAS_STEALTHCHOP, SET_STEPPING_MODE(Z));
- TERN_(I_HAS_STEALTHCHOP, SET_STEPPING_MODE(I));
- TERN_(J_HAS_STEALTHCHOP, SET_STEPPING_MODE(J));
- TERN_(K_HAS_STEALTHCHOP, SET_STEPPING_MODE(K));
- TERN_(U_HAS_STEALTHCHOP, SET_STEPPING_MODE(U));
- TERN_(V_HAS_STEALTHCHOP, SET_STEPPING_MODE(V));
- TERN_(W_HAS_STEALTHCHOP, SET_STEPPING_MODE(W));
- TERN_(X2_HAS_STEALTHCHOP, SET_STEPPING_MODE(X2));
- TERN_(Y2_HAS_STEALTHCHOP, SET_STEPPING_MODE(Y2));
- TERN_(Z2_HAS_STEALTHCHOP, SET_STEPPING_MODE(Z2));
- TERN_(Z3_HAS_STEALTHCHOP, SET_STEPPING_MODE(Z3));
- TERN_(Z4_HAS_STEALTHCHOP, SET_STEPPING_MODE(Z4));
- TERN_(E0_HAS_STEALTHCHOP, SET_STEPPING_MODE(E0));
- TERN_(E1_HAS_STEALTHCHOP, SET_STEPPING_MODE(E1));
- TERN_(E2_HAS_STEALTHCHOP, SET_STEPPING_MODE(E2));
- TERN_(E3_HAS_STEALTHCHOP, SET_STEPPING_MODE(E3));
- TERN_(E4_HAS_STEALTHCHOP, SET_STEPPING_MODE(E4));
- TERN_(E5_HAS_STEALTHCHOP, SET_STEPPING_MODE(E5));
- TERN_(E6_HAS_STEALTHCHOP, SET_STEPPING_MODE(E6));
- TERN_(E7_HAS_STEALTHCHOP, SET_STEPPING_MODE(E7));
- }
- #endif
- }
-
- //
- // Linear Advance
- //
- {
- float extruder_advance_K[DISTINCT_E];
- _FIELD_TEST(planner_extruder_advance_K);
- EEPROM_READ(extruder_advance_K);
- #if ENABLED(LIN_ADVANCE)
- if (!validating)
- COPY(planner.extruder_advance_K, extruder_advance_K);
- #endif
- }
-
- //
- // Motor Current PWM
- //
- {
- _FIELD_TEST(motor_current_setting);
- uint32_t motor_current_setting[MOTOR_CURRENT_COUNT]
- #if HAS_MOTOR_CURRENT_SPI
- = DIGIPOT_MOTOR_CURRENT
- #endif
- ;
- #if HAS_MOTOR_CURRENT_SPI
- DEBUG_ECHO_MSG("DIGIPOTS Loading");
- #endif
- EEPROM_READ(motor_current_setting);
- #if HAS_MOTOR_CURRENT_SPI
- DEBUG_ECHO_MSG("DIGIPOTS Loaded");
- #endif
- #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM
- if (!validating)
- COPY(stepper.motor_current_setting, motor_current_setting);
- #endif
- }
-
- //
- // CNC Coordinate System
- //
- {
- _FIELD_TEST(coordinate_system);
- #if ENABLED(CNC_COORDINATE_SYSTEMS)
- if (!validating) (void)gcode.select_coordinate_system(-1); // Go back to machine space
- EEPROM_READ(gcode.coordinate_system);
- #else
- xyz_pos_t coordinate_system[MAX_COORDINATE_SYSTEMS];
- EEPROM_READ(coordinate_system);
- #endif
- }
-
- //
- // Skew correction factors
- //
- {
- skew_factor_t skew_factor;
- _FIELD_TEST(planner_skew_factor);
- EEPROM_READ(skew_factor);
- #if ENABLED(SKEW_CORRECTION_GCODE)
- if (!validating) {
- planner.skew_factor.xy = skew_factor.xy;
- #if ENABLED(SKEW_CORRECTION_FOR_Z)
- planner.skew_factor.xz = skew_factor.xz;
- planner.skew_factor.yz = skew_factor.yz;
- #endif
- }
- #endif
- }
-
- //
- // Advanced Pause filament load & unload lengths
- //
- #if HAS_EXTRUDERS
- {
- #if DISABLED(ADVANCED_PAUSE_FEATURE)
- fil_change_settings_t fc_settings[EXTRUDERS];
- #endif
- _FIELD_TEST(fc_settings);
- EEPROM_READ(fc_settings);
- }
- #endif
-
- //
- // Tool-change settings
- //
- #if HAS_MULTI_EXTRUDER
- _FIELD_TEST(toolchange_settings);
- EEPROM_READ(toolchange_settings);
- #endif
-
- //
- // Backlash Compensation
- //
- {
- xyz_float_t backlash_distance_mm;
- uint8_t backlash_correction;
- float backlash_smoothing_mm;
-
- _FIELD_TEST(backlash_distance_mm);
- EEPROM_READ(backlash_distance_mm);
- EEPROM_READ(backlash_correction);
- EEPROM_READ(backlash_smoothing_mm);
-
- #if ENABLED(BACKLASH_GCODE)
- LOOP_NUM_AXES(axis) backlash.set_distance_mm((AxisEnum)axis, backlash_distance_mm[axis]);
- backlash.set_correction_uint8(backlash_correction);
- #ifdef BACKLASH_SMOOTHING_MM
- backlash.set_smoothing_mm(backlash_smoothing_mm);
- #endif
- #endif
- }
-
- //
- // Extensible UI User Data
- //
- #if ENABLED(EXTENSIBLE_UI)
- { // This is a significant hardware change; don't reserve EEPROM space when not present
- const char extui_data[ExtUI::eeprom_data_size] = { 0 };
- _FIELD_TEST(extui_data);
- EEPROM_READ(extui_data);
- if (!validating) ExtUI::onLoadSettings(extui_data);
- }
- #endif
-
- //
- // Creality DWIN User Data
- //
- #if ENABLED(DWIN_LCD_PROUI)
- {
- const char dwin_data[eeprom_data_size] = { 0 };
- _FIELD_TEST(dwin_data);
- EEPROM_READ(dwin_data);
- if (!validating) DWIN_CopySettingsFrom(dwin_data);
- }
- #elif ENABLED(DWIN_CREALITY_LCD_JYERSUI)
- {
- const char dwin_settings[CrealityDWIN.eeprom_data_size] = { 0 };
- _FIELD_TEST(dwin_settings);
- EEPROM_READ(dwin_settings);
- if (!validating) CrealityDWIN.Load_Settings(dwin_settings);
- }
- #endif
-
- //
- // Case Light Brightness
- //
- #if CASELIGHT_USES_BRIGHTNESS
- _FIELD_TEST(caselight_brightness);
- EEPROM_READ(caselight.brightness);
- #endif
-
- //
- // Password feature
- //
- #if ENABLED(PASSWORD_FEATURE)
- _FIELD_TEST(password_is_set);
- EEPROM_READ(password.is_set);
- EEPROM_READ(password.value);
- #endif
-
- //
- // TOUCH_SCREEN_CALIBRATION
- //
- #if ENABLED(TOUCH_SCREEN_CALIBRATION)
- _FIELD_TEST(touch_calibration_data);
- EEPROM_READ(touch_calibration.calibration);
- #endif
-
- //
- // Ethernet network info
- //
- #if HAS_ETHERNET
- _FIELD_TEST(ethernet_hardware_enabled);
- uint32_t ethernet_ip, ethernet_dns, ethernet_gateway, ethernet_subnet;
- EEPROM_READ(ethernet.hardware_enabled);
- EEPROM_READ(ethernet_ip); ethernet.ip = ethernet_ip;
- EEPROM_READ(ethernet_dns); ethernet.myDns = ethernet_dns;
- EEPROM_READ(ethernet_gateway); ethernet.gateway = ethernet_gateway;
- EEPROM_READ(ethernet_subnet); ethernet.subnet = ethernet_subnet;
- #endif
-
- //
- // Buzzer enable/disable
- //
- #if ENABLED(SOUND_MENU_ITEM)
- _FIELD_TEST(sound_on);
- EEPROM_READ(ui.sound_on);
- #endif
-
- //
- // Fan tachometer check
- //
- #if HAS_FANCHECK
- _FIELD_TEST(fan_check_enabled);
- EEPROM_READ(fan_check.enabled);
- #endif
-
- //
- // MKS UI controller
- //
- #if ENABLED(DGUS_LCD_UI_MKS)
- _FIELD_TEST(mks_language_index);
- EEPROM_READ(mks_language_index);
- EEPROM_READ(mks_corner_offsets);
- EEPROM_READ(mks_park_pos);
- EEPROM_READ(mks_min_extrusion_temp);
- #endif
-
- //
- // Selected LCD language
- //
- #if HAS_MULTI_LANGUAGE
- {
- uint8_t ui_language;
- EEPROM_READ(ui_language);
- if (ui_language >= NUM_LANGUAGES) ui_language = 0;
- ui.set_language(ui_language);
- }
- #endif
-
- //
- // Model predictive control
- //
- #if ENABLED(MPCTEMP)
- {
- HOTEND_LOOP()
- EEPROM_READ(thermalManager.temp_hotend[e].constants);
- }
- #endif
-
- //
- // Validate Final Size and CRC
- //
- eeprom_error = size_error(eeprom_index - (EEPROM_OFFSET));
- if (eeprom_error) {
- DEBUG_ECHO_MSG("Index: ", eeprom_index - (EEPROM_OFFSET), " Size: ", datasize());
- IF_DISABLED(EEPROM_AUTO_INIT, ui.eeprom_alert_index());
- }
- else if (working_crc != stored_crc) {
- eeprom_error = true;
- DEBUG_ERROR_MSG("EEPROM CRC mismatch - (stored) ", stored_crc, " != ", working_crc, " (calculated)!");
- TERN_(DWIN_LCD_PROUI, LCD_MESSAGE(MSG_ERR_EEPROM_CRC));
- TERN_(HOST_EEPROM_CHITCHAT, hostui.notify(GET_TEXT_F(MSG_ERR_EEPROM_CRC)));
- IF_DISABLED(EEPROM_AUTO_INIT, ui.eeprom_alert_crc());
- }
- else if (!validating) {
- DEBUG_ECHO_START();
- DEBUG_ECHO(version);
- DEBUG_ECHOLNPGM(" stored settings retrieved (", eeprom_index - (EEPROM_OFFSET), " bytes; crc ", (uint32_t)working_crc, ")");
- TERN_(HOST_EEPROM_CHITCHAT, hostui.notify(F("Stored settings retrieved")));
- }
-
- if (!validating && !eeprom_error) postprocess();
-
- #if ENABLED(AUTO_BED_LEVELING_UBL)
- if (!validating) {
- bedlevel.report_state();
-
- if (!bedlevel.sanity_check()) {
- #if BOTH(EEPROM_CHITCHAT, DEBUG_LEVELING_FEATURE)
- bedlevel.echo_name();
- DEBUG_ECHOLNPGM(" initialized.\n");
- #endif
- }
- else {
- eeprom_error = true;
- #if BOTH(EEPROM_CHITCHAT, DEBUG_LEVELING_FEATURE)
- DEBUG_ECHOPGM("?Can't enable ");
- bedlevel.echo_name();
- DEBUG_ECHOLNPGM(".");
- #endif
- bedlevel.reset();
- }
-
- if (bedlevel.storage_slot >= 0) {
- load_mesh(bedlevel.storage_slot);
- DEBUG_ECHOLNPGM("Mesh ", bedlevel.storage_slot, " loaded from storage.");
- }
- else {
- bedlevel.reset();
- DEBUG_ECHOLNPGM("UBL reset");
- }
- }
- #endif
- }
-
- #if ENABLED(EEPROM_CHITCHAT) && DISABLED(DISABLE_M503)
- // Report the EEPROM settings
- if (!validating && TERN1(EEPROM_BOOT_SILENT, IsRunning())) report();
- #endif
-
- EEPROM_FINISH();
-
- return !eeprom_error;
- }
-
- #ifdef ARCHIM2_SPI_FLASH_EEPROM_BACKUP_SIZE
- extern bool restoreEEPROM();
- #endif
-
- bool MarlinSettings::validate() {
- validating = true;
- #ifdef ARCHIM2_SPI_FLASH_EEPROM_BACKUP_SIZE
- bool success = _load();
- if (!success && restoreEEPROM()) {
- SERIAL_ECHOLNPGM("Recovered backup EEPROM settings from SPI Flash");
- success = _load();
- }
- #else
- const bool success = _load();
- #endif
- validating = false;
- return success;
- }
-
- bool MarlinSettings::load() {
- if (validate()) {
- const bool success = _load();
- TERN_(EXTENSIBLE_UI, ExtUI::onSettingsLoaded(success));
- return success;
- }
- reset();
- #if EITHER(EEPROM_AUTO_INIT, EEPROM_INIT_NOW)
- (void)save();
- SERIAL_ECHO_MSG("EEPROM Initialized");
- #endif
- return false;
- }
-
- #if ENABLED(AUTO_BED_LEVELING_UBL)
-
- inline void ubl_invalid_slot(const int s) {
- DEBUG_ECHOLNPGM("?Invalid slot.\n", s, " mesh slots available.");
- UNUSED(s);
- }
-
- // 128 (+1 because of the change to capacity rather than last valid address)
- // is a placeholder for the size of the MAT; the MAT will always
- // live at the very end of the eeprom
- const uint16_t MarlinSettings::meshes_end = persistentStore.capacity() - 129;
-
- uint16_t MarlinSettings::meshes_start_index() {
- // Pad the end of configuration data so it can float up
- // or down a little bit without disrupting the mesh data
- return (datasize() + EEPROM_OFFSET + 32) & 0xFFF8;
- }
-
- #define MESH_STORE_SIZE sizeof(TERN(OPTIMIZED_MESH_STORAGE, mesh_store_t, bedlevel.z_values))
-
- uint16_t MarlinSettings::calc_num_meshes() {
- return (meshes_end - meshes_start_index()) / MESH_STORE_SIZE;
- }
-
- int MarlinSettings::mesh_slot_offset(const int8_t slot) {
- return meshes_end - (slot + 1) * MESH_STORE_SIZE;
- }
-
- void MarlinSettings::store_mesh(const int8_t slot) {
-
- #if ENABLED(AUTO_BED_LEVELING_UBL)
- const int16_t a = calc_num_meshes();
- if (!WITHIN(slot, 0, a - 1)) {
- ubl_invalid_slot(a);
- DEBUG_ECHOLNPGM("E2END=", persistentStore.capacity() - 1, " meshes_end=", meshes_end, " slot=", slot);
- DEBUG_EOL();
- return;
- }
-
- int pos = mesh_slot_offset(slot);
- uint16_t crc = 0;
-
- #if ENABLED(OPTIMIZED_MESH_STORAGE)
- int16_t z_mesh_store[GRID_MAX_POINTS_X][GRID_MAX_POINTS_Y];
- bedlevel.set_store_from_mesh(bedlevel.z_values, z_mesh_store);
- uint8_t * const src = (uint8_t*)&z_mesh_store;
- #else
- uint8_t * const src = (uint8_t*)&bedlevel.z_values;
- #endif
-
- // Write crc to MAT along with other data, or just tack on to the beginning or end
- persistentStore.access_start();
- const bool status = persistentStore.write_data(pos, src, MESH_STORE_SIZE, &crc);
- persistentStore.access_finish();
-
- if (status) SERIAL_ECHOLNPGM("?Unable to save mesh data.");
- else DEBUG_ECHOLNPGM("Mesh saved in slot ", slot);
-
- #else
-
- // Other mesh types
-
- #endif
- }
-
- void MarlinSettings::load_mesh(const int8_t slot, void * const into/*=nullptr*/) {
-
- #if ENABLED(AUTO_BED_LEVELING_UBL)
-
- const int16_t a = settings.calc_num_meshes();
-
- if (!WITHIN(slot, 0, a - 1)) {
- ubl_invalid_slot(a);
- return;
- }
-
- int pos = mesh_slot_offset(slot);
- uint16_t crc = 0;
- #if ENABLED(OPTIMIZED_MESH_STORAGE)
- int16_t z_mesh_store[GRID_MAX_POINTS_X][GRID_MAX_POINTS_Y];
- uint8_t * const dest = (uint8_t*)&z_mesh_store;
- #else
- uint8_t * const dest = into ? (uint8_t*)into : (uint8_t*)&bedlevel.z_values;
- #endif
-
- persistentStore.access_start();
- uint16_t status = persistentStore.read_data(pos, dest, MESH_STORE_SIZE, &crc);
- persistentStore.access_finish();
-
- #if ENABLED(OPTIMIZED_MESH_STORAGE)
- if (into) {
- float z_values[GRID_MAX_POINTS_X][GRID_MAX_POINTS_Y];
- bedlevel.set_mesh_from_store(z_mesh_store, z_values);
- memcpy(into, z_values, sizeof(z_values));
- }
- else
- bedlevel.set_mesh_from_store(z_mesh_store, bedlevel.z_values);
- #endif
-
- #if ENABLED(DWIN_LCD_PROUI)
- status = !BedLevelTools.meshvalidate();
- if (status) {
- bedlevel.invalidate();
- LCD_MESSAGE(MSG_UBL_MESH_INVALID);
- }
- else
- ui.status_printf(0, GET_TEXT_F(MSG_MESH_LOADED), bedlevel.storage_slot);
- #endif
-
- if (status) SERIAL_ECHOLNPGM("?Unable to load mesh data.");
- else DEBUG_ECHOLNPGM("Mesh loaded from slot ", slot);
-
- EEPROM_FINISH();
-
- #else
-
- // Other mesh types
-
- #endif
- }
-
- //void MarlinSettings::delete_mesh() { return; }
- //void MarlinSettings::defrag_meshes() { return; }
-
- #endif // AUTO_BED_LEVELING_UBL
-
- #else // !EEPROM_SETTINGS
-
- bool MarlinSettings::save() {
- DEBUG_ERROR_MSG("EEPROM disabled");
- return false;
- }
-
- #endif // !EEPROM_SETTINGS
-
- /**
- * M502 - Reset Configuration
- */
- void MarlinSettings::reset() {
- LOOP_DISTINCT_AXES(i) {
- planner.settings.max_acceleration_mm_per_s2[i] = pgm_read_dword(&_DMA[ALIM(i, _DMA)]);
- planner.settings.axis_steps_per_mm[i] = pgm_read_float(&_DASU[ALIM(i, _DASU)]);
- planner.settings.max_feedrate_mm_s[i] = pgm_read_float(&_DMF[ALIM(i, _DMF)]);
- }
-
- planner.settings.min_segment_time_us = DEFAULT_MINSEGMENTTIME;
- planner.settings.acceleration = DEFAULT_ACCELERATION;
- planner.settings.retract_acceleration = DEFAULT_RETRACT_ACCELERATION;
- planner.settings.travel_acceleration = DEFAULT_TRAVEL_ACCELERATION;
- planner.settings.min_feedrate_mm_s = feedRate_t(DEFAULT_MINIMUMFEEDRATE);
- planner.settings.min_travel_feedrate_mm_s = feedRate_t(DEFAULT_MINTRAVELFEEDRATE);
-
- #if HAS_CLASSIC_JERK
- #ifndef DEFAULT_XJERK
- #define DEFAULT_XJERK 0
- #endif
- #if HAS_Y_AXIS && !defined(DEFAULT_YJERK)
- #define DEFAULT_YJERK 0
- #endif
- #if HAS_Z_AXIS && !defined(DEFAULT_ZJERK)
- #define DEFAULT_ZJERK 0
- #endif
- #if HAS_I_AXIS && !defined(DEFAULT_IJERK)
- #define DEFAULT_IJERK 0
- #endif
- #if HAS_J_AXIS && !defined(DEFAULT_JJERK)
- #define DEFAULT_JJERK 0
- #endif
- #if HAS_K_AXIS && !defined(DEFAULT_KJERK)
- #define DEFAULT_KJERK 0
- #endif
- #if HAS_U_AXIS && !defined(DEFAULT_UJERK)
- #define DEFAULT_UJERK 0
- #endif
- #if HAS_V_AXIS && !defined(DEFAULT_VJERK)
- #define DEFAULT_VJERK 0
- #endif
- #if HAS_W_AXIS && !defined(DEFAULT_WJERK)
- #define DEFAULT_WJERK 0
- #endif
- planner.max_jerk.set(
- NUM_AXIS_LIST(DEFAULT_XJERK, DEFAULT_YJERK, DEFAULT_ZJERK, DEFAULT_IJERK, DEFAULT_JJERK, DEFAULT_KJERK, DEFAULT_UJERK, DEFAULT_VJERK, DEFAULT_WJERK)
- );
- TERN_(HAS_CLASSIC_E_JERK, planner.max_jerk.e = DEFAULT_EJERK);
- #endif
-
- TERN_(HAS_JUNCTION_DEVIATION, planner.junction_deviation_mm = float(JUNCTION_DEVIATION_MM));
-
- #if HAS_SCARA_OFFSET
- scara_home_offset.reset();
- #elif HAS_HOME_OFFSET
- home_offset.reset();
- #endif
-
- TERN_(HAS_HOTEND_OFFSET, reset_hotend_offsets());
-
- //
- // Filament Runout Sensor
- //
-
- #if HAS_FILAMENT_SENSOR
- runout.enabled = FIL_RUNOUT_ENABLED_DEFAULT;
- runout.reset();
- TERN_(HAS_FILAMENT_RUNOUT_DISTANCE, runout.set_runout_distance(FILAMENT_RUNOUT_DISTANCE_MM));
- #endif
-
- //
- // Tool-change Settings
- //
-
- #if HAS_MULTI_EXTRUDER
- #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
- toolchange_settings.swap_length = TOOLCHANGE_FS_LENGTH;
- toolchange_settings.extra_resume = TOOLCHANGE_FS_EXTRA_RESUME_LENGTH;
- toolchange_settings.retract_speed = TOOLCHANGE_FS_RETRACT_SPEED;
- toolchange_settings.unretract_speed = TOOLCHANGE_FS_UNRETRACT_SPEED;
- toolchange_settings.extra_prime = TOOLCHANGE_FS_EXTRA_PRIME;
- toolchange_settings.prime_speed = TOOLCHANGE_FS_PRIME_SPEED;
- toolchange_settings.wipe_retract = TOOLCHANGE_FS_WIPE_RETRACT;
- toolchange_settings.fan_speed = TOOLCHANGE_FS_FAN_SPEED;
- toolchange_settings.fan_time = TOOLCHANGE_FS_FAN_TIME;
- #endif
-
- #if ENABLED(TOOLCHANGE_FS_PRIME_FIRST_USED)
- enable_first_prime = false;
- #endif
-
- #if ENABLED(TOOLCHANGE_PARK)
- constexpr xyz_pos_t tpxy = TOOLCHANGE_PARK_XY;
- toolchange_settings.enable_park = true;
- toolchange_settings.change_point = tpxy;
- #endif
-
- toolchange_settings.z_raise = TOOLCHANGE_ZRAISE;
-
- #if ENABLED(TOOLCHANGE_MIGRATION_FEATURE)
- migration = migration_defaults;
- #endif
-
- #endif
-
- #if ENABLED(BACKLASH_GCODE)
- backlash.set_correction(BACKLASH_CORRECTION);
- constexpr xyz_float_t tmp = BACKLASH_DISTANCE_MM;
- LOOP_NUM_AXES(axis) backlash.set_distance_mm((AxisEnum)axis, tmp[axis]);
- #ifdef BACKLASH_SMOOTHING_MM
- backlash.set_smoothing_mm(BACKLASH_SMOOTHING_MM);
- #endif
- #endif
-
- TERN_(DWIN_CREALITY_LCD_JYERSUI, CrealityDWIN.Reset_Settings());
-
- //
- // Case Light Brightness
- //
- TERN_(CASELIGHT_USES_BRIGHTNESS, caselight.brightness = CASE_LIGHT_DEFAULT_BRIGHTNESS);
-
- //
- // TOUCH_SCREEN_CALIBRATION
- //
- TERN_(TOUCH_SCREEN_CALIBRATION, touch_calibration.calibration_reset());
-
- //
- // Buzzer enable/disable
- //
- #if ENABLED(SOUND_MENU_ITEM)
- ui.sound_on = ENABLED(SOUND_ON_DEFAULT);
- #endif
-
- //
- // Magnetic Parking Extruder
- //
- TERN_(MAGNETIC_PARKING_EXTRUDER, mpe_settings_init());
-
- //
- // Global Leveling
- //
- TERN_(ENABLE_LEVELING_FADE_HEIGHT, new_z_fade_height = (DEFAULT_LEVELING_FADE_HEIGHT));
- TERN_(HAS_LEVELING, reset_bed_level());
-
- //
- // X Axis Twist Compensation
- //
- TERN_(X_AXIS_TWIST_COMPENSATION, xatc.reset());
-
- //
- // Nozzle-to-probe Offset
- //
- #if HAS_BED_PROBE
- constexpr float dpo[] = NOZZLE_TO_PROBE_OFFSET;
- static_assert(COUNT(dpo) == NUM_AXES, "NOZZLE_TO_PROBE_OFFSET must contain offsets for each linear axis X, Y, Z....");
- #if HAS_PROBE_XY_OFFSET
- LOOP_NUM_AXES(a) probe.offset[a] = dpo[a];
- #else
- probe.offset.set(NUM_AXIS_LIST(0, 0, dpo[Z_AXIS], 0, 0, 0, 0, 0, 0));
- #endif
- #endif
-
- //
- // Z Stepper Auto-alignment points
- //
- TERN_(Z_STEPPER_AUTO_ALIGN, z_stepper_align.reset_to_default());
-
- //
- // Servo Angles
- //
- TERN_(EDITABLE_SERVO_ANGLES, COPY(servo_angles, base_servo_angles)); // When not editable only one copy of servo angles exists
-
- //
- // Probe Temperature Compensation
- //
- TERN_(HAS_PTC, ptc.reset());
-
- //
- // BLTouch
- //
- #ifdef BLTOUCH_HS_MODE
- bltouch.high_speed_mode = ENABLED(BLTOUCH_HS_MODE);
- #endif
-
- //
- // Kinematic settings
- //
-
- #if IS_KINEMATIC
- segments_per_second = (
- TERN_(DELTA, DELTA_SEGMENTS_PER_SECOND)
- TERN_(IS_SCARA, SCARA_SEGMENTS_PER_SECOND)
- TERN_(POLARGRAPH, POLAR_SEGMENTS_PER_SECOND)
- );
- #if ENABLED(DELTA)
- const abc_float_t adj = DELTA_ENDSTOP_ADJ, dta = DELTA_TOWER_ANGLE_TRIM, ddr = DELTA_DIAGONAL_ROD_TRIM_TOWER;
- delta_height = DELTA_HEIGHT;
- delta_endstop_adj = adj;
- delta_radius = DELTA_RADIUS;
- delta_diagonal_rod = DELTA_DIAGONAL_ROD;
- delta_tower_angle_trim = dta;
- delta_diagonal_rod_trim = ddr;
- #elif ENABLED(POLARGRAPH)
- draw_area_min.set(X_MIN_POS, Y_MIN_POS);
- draw_area_max.set(X_MAX_POS, Y_MAX_POS);
- polargraph_max_belt_len = POLARGRAPH_MAX_BELT_LEN;
- #endif
- #endif
-
- //
- // Endstop Adjustments
- //
-
- #if ENABLED(X_DUAL_ENDSTOPS)
- #ifndef X2_ENDSTOP_ADJUSTMENT
- #define X2_ENDSTOP_ADJUSTMENT 0
- #endif
- endstops.x2_endstop_adj = X2_ENDSTOP_ADJUSTMENT;
- #endif
-
- #if ENABLED(Y_DUAL_ENDSTOPS)
- #ifndef Y2_ENDSTOP_ADJUSTMENT
- #define Y2_ENDSTOP_ADJUSTMENT 0
- #endif
- endstops.y2_endstop_adj = Y2_ENDSTOP_ADJUSTMENT;
- #endif
-
- #if ENABLED(Z_MULTI_ENDSTOPS)
- #ifndef Z2_ENDSTOP_ADJUSTMENT
- #define Z2_ENDSTOP_ADJUSTMENT 0
- #endif
- endstops.z2_endstop_adj = Z2_ENDSTOP_ADJUSTMENT;
- #if NUM_Z_STEPPERS >= 3
- #ifndef Z3_ENDSTOP_ADJUSTMENT
- #define Z3_ENDSTOP_ADJUSTMENT 0
- #endif
- endstops.z3_endstop_adj = Z3_ENDSTOP_ADJUSTMENT;
- #endif
- #if NUM_Z_STEPPERS >= 4
- #ifndef Z4_ENDSTOP_ADJUSTMENT
- #define Z4_ENDSTOP_ADJUSTMENT 0
- #endif
- endstops.z4_endstop_adj = Z4_ENDSTOP_ADJUSTMENT;
- #endif
- #endif
-
- //
- // Preheat parameters
- //
- #if HAS_PREHEAT
- #define _PITEM(N,T) PREHEAT_##N##_##T,
- #if HAS_HOTEND
- constexpr uint16_t hpre[] = { REPEAT2_S(1, INCREMENT(PREHEAT_COUNT), _PITEM, TEMP_HOTEND) };
- #endif
- #if HAS_HEATED_BED
- constexpr uint16_t bpre[] = { REPEAT2_S(1, INCREMENT(PREHEAT_COUNT), _PITEM, TEMP_BED) };
- #endif
- #if HAS_FAN
- constexpr uint8_t fpre[] = { REPEAT2_S(1, INCREMENT(PREHEAT_COUNT), _PITEM, FAN_SPEED) };
- #endif
- LOOP_L_N(i, PREHEAT_COUNT) {
- TERN_(HAS_HOTEND, ui.material_preset[i].hotend_temp = hpre[i]);
- TERN_(HAS_HEATED_BED, ui.material_preset[i].bed_temp = bpre[i]);
- TERN_(HAS_FAN, ui.material_preset[i].fan_speed = fpre[i]);
- }
- #endif
-
- //
- // Hotend PID
- //
-
- #if ENABLED(PIDTEMP)
- #if ENABLED(PID_PARAMS_PER_HOTEND)
- constexpr float defKp[] =
- #ifdef DEFAULT_Kp_LIST
- DEFAULT_Kp_LIST
- #else
- ARRAY_BY_HOTENDS1(DEFAULT_Kp)
- #endif
- , defKi[] =
- #ifdef DEFAULT_Ki_LIST
- DEFAULT_Ki_LIST
- #else
- ARRAY_BY_HOTENDS1(DEFAULT_Ki)
- #endif
- , defKd[] =
- #ifdef DEFAULT_Kd_LIST
- DEFAULT_Kd_LIST
- #else
- ARRAY_BY_HOTENDS1(DEFAULT_Kd)
- #endif
- ;
- static_assert(WITHIN(COUNT(defKp), 1, HOTENDS), "DEFAULT_Kp_LIST must have between 1 and HOTENDS items.");
- static_assert(WITHIN(COUNT(defKi), 1, HOTENDS), "DEFAULT_Ki_LIST must have between 1 and HOTENDS items.");
- static_assert(WITHIN(COUNT(defKd), 1, HOTENDS), "DEFAULT_Kd_LIST must have between 1 and HOTENDS items.");
- #if ENABLED(PID_EXTRUSION_SCALING)
- constexpr float defKc[] =
- #ifdef DEFAULT_Kc_LIST
- DEFAULT_Kc_LIST
- #else
- ARRAY_BY_HOTENDS1(DEFAULT_Kc)
- #endif
- ;
- static_assert(WITHIN(COUNT(defKc), 1, HOTENDS), "DEFAULT_Kc_LIST must have between 1 and HOTENDS items.");
- #endif
- #if ENABLED(PID_FAN_SCALING)
- constexpr float defKf[] =
- #ifdef DEFAULT_Kf_LIST
- DEFAULT_Kf_LIST
- #else
- ARRAY_BY_HOTENDS1(DEFAULT_Kf)
- #endif
- ;
- static_assert(WITHIN(COUNT(defKf), 1, HOTENDS), "DEFAULT_Kf_LIST must have between 1 and HOTENDS items.");
- #endif
- #define PID_DEFAULT(N,E) def##N[E]
- #else
- #define PID_DEFAULT(N,E) DEFAULT_##N
- #endif
- HOTEND_LOOP() {
- thermalManager.temp_hotend[e].pid.set(
- PID_DEFAULT(Kp, ALIM(e, defKp)),
- PID_DEFAULT(Ki, ALIM(e, defKi)),
- PID_DEFAULT(Kd, ALIM(e, defKd))
- OPTARG(PID_EXTRUSION_SCALING, PID_DEFAULT(Kc, ALIM(e, defKc)))
- OPTARG(PID_FAN_SCALING, PID_DEFAULT(Kf, ALIM(e, defKf)))
- );
- }
- #endif
-
- //
- // PID Extrusion Scaling
- //
- TERN_(PID_EXTRUSION_SCALING, thermalManager.lpq_len = 20); // Default last-position-queue size
-
- //
- // Heated Bed PID
- //
-
- #if ENABLED(PIDTEMPBED)
- thermalManager.temp_bed.pid.set(DEFAULT_bedKp, DEFAULT_bedKi, DEFAULT_bedKd);
- #endif
-
- //
- // Heated Chamber PID
- //
-
- #if ENABLED(PIDTEMPCHAMBER)
- thermalManager.temp_chamber.pid.set(DEFAULT_chamberKp, DEFAULT_chamberKi, DEFAULT_chamberKd);
- #endif
-
- //
- // User-Defined Thermistors
- //
- TERN_(HAS_USER_THERMISTORS, thermalManager.reset_user_thermistors());
-
- //
- // Power Monitor
- //
- TERN_(POWER_MONITOR, power_monitor.reset());
-
- //
- // LCD Contrast
- //
- TERN_(HAS_LCD_CONTRAST, ui.contrast = LCD_CONTRAST_DEFAULT);
-
- //
- // LCD Brightness
- //
- TERN_(HAS_LCD_BRIGHTNESS, ui.brightness = LCD_BRIGHTNESS_DEFAULT);
-
- //
- // LCD Backlight / Sleep Timeout
- //
- #if LCD_BACKLIGHT_TIMEOUT_MINS
- ui.backlight_timeout_minutes = LCD_BACKLIGHT_TIMEOUT_MINS;
- #elif HAS_DISPLAY_SLEEP
- ui.sleep_timeout_minutes = TERN(TOUCH_SCREEN, TOUCH_IDLE_SLEEP_MINS, DISPLAY_SLEEP_MINUTES);
- #endif
-
- //
- // Controller Fan
- //
- TERN_(USE_CONTROLLER_FAN, controllerFan.reset());
-
- //
- // Power-Loss Recovery
- //
- TERN_(POWER_LOSS_RECOVERY, recovery.enable(ENABLED(PLR_ENABLED_DEFAULT)));
-
- //
- // Firmware Retraction
- //
- TERN_(FWRETRACT, fwretract.reset());
-
- //
- // Volumetric & Filament Size
- //
-
- #if DISABLED(NO_VOLUMETRICS)
- parser.volumetric_enabled = ENABLED(VOLUMETRIC_DEFAULT_ON);
- LOOP_L_N(q, COUNT(planner.filament_size))
- planner.filament_size[q] = DEFAULT_NOMINAL_FILAMENT_DIA;
- #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT)
- LOOP_L_N(q, COUNT(planner.volumetric_extruder_limit))
- planner.volumetric_extruder_limit[q] = DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT;
- #endif
- #endif
-
- endstops.enable_globally(ENABLED(ENDSTOPS_ALWAYS_ON_DEFAULT));
-
- reset_stepper_drivers();
-
- //
- // Linear Advance
- //
- #if ENABLED(LIN_ADVANCE)
- #if ENABLED(DISTINCT_E_FACTORS)
- constexpr float linAdvanceK[] = ADVANCE_K;
- EXTRUDER_LOOP() {
- const float a = linAdvanceK[_MAX(e, COUNT(linAdvanceK) - 1)];
- planner.extruder_advance_K[e] = a;
- TERN_(ADVANCE_K_EXTRA, other_extruder_advance_K[e] = a);
- }
- #else
- planner.extruder_advance_K[0] = ADVANCE_K;
- #endif
- #endif
-
- //
- // Motor Current PWM
- //
-
- #if HAS_MOTOR_CURRENT_PWM
- constexpr uint32_t tmp_motor_current_setting[MOTOR_CURRENT_COUNT] = PWM_MOTOR_CURRENT;
- LOOP_L_N(q, MOTOR_CURRENT_COUNT)
- stepper.set_digipot_current(q, (stepper.motor_current_setting[q] = tmp_motor_current_setting[q]));
- #endif
-
- //
- // DIGIPOTS
- //
- #if HAS_MOTOR_CURRENT_SPI
- static constexpr uint32_t tmp_motor_current_setting[] = DIGIPOT_MOTOR_CURRENT;
- DEBUG_ECHOLNPGM("Writing Digipot");
- LOOP_L_N(q, COUNT(tmp_motor_current_setting))
- stepper.set_digipot_current(q, tmp_motor_current_setting[q]);
- DEBUG_ECHOLNPGM("Digipot Written");
- #endif
-
- //
- // CNC Coordinate System
- //
- TERN_(CNC_COORDINATE_SYSTEMS, (void)gcode.select_coordinate_system(-1)); // Go back to machine space
-
- //
- // Skew Correction
- //
- #if ENABLED(SKEW_CORRECTION_GCODE)
- planner.skew_factor.xy = XY_SKEW_FACTOR;
- #if ENABLED(SKEW_CORRECTION_FOR_Z)
- planner.skew_factor.xz = XZ_SKEW_FACTOR;
- planner.skew_factor.yz = YZ_SKEW_FACTOR;
- #endif
- #endif
-
- //
- // Advanced Pause filament load & unload lengths
- //
- #if ENABLED(ADVANCED_PAUSE_FEATURE)
- EXTRUDER_LOOP() {
- fc_settings[e].unload_length = FILAMENT_CHANGE_UNLOAD_LENGTH;
- fc_settings[e].load_length = FILAMENT_CHANGE_FAST_LOAD_LENGTH;
- }
- #endif
-
- #if ENABLED(PASSWORD_FEATURE)
- #ifdef PASSWORD_DEFAULT_VALUE
- password.is_set = true;
- password.value = PASSWORD_DEFAULT_VALUE;
- #else
- password.is_set = false;
- #endif
- #endif
-
- //
- // Fan tachometer check
- //
- TERN_(HAS_FANCHECK, fan_check.enabled = true);
-
- //
- // MKS UI controller
- //
- TERN_(DGUS_LCD_UI_MKS, MKS_reset_settings());
-
- //
- // Ender-3 V2 with ProUI
- //
- TERN_(DWIN_LCD_PROUI, DWIN_SetDataDefaults());
-
- //
- // Model predictive control
- //
- #if ENABLED(MPCTEMP)
- constexpr float _mpc_heater_power[] = MPC_HEATER_POWER;
- constexpr float _mpc_block_heat_capacity[] = MPC_BLOCK_HEAT_CAPACITY;
- constexpr float _mpc_sensor_responsiveness[] = MPC_SENSOR_RESPONSIVENESS;
- constexpr float _mpc_ambient_xfer_coeff[] = MPC_AMBIENT_XFER_COEFF;
- #if ENABLED(MPC_INCLUDE_FAN)
- constexpr float _mpc_ambient_xfer_coeff_fan255[] = MPC_AMBIENT_XFER_COEFF_FAN255;
- #endif
- constexpr float _filament_heat_capacity_permm[] = FILAMENT_HEAT_CAPACITY_PERMM;
-
- static_assert(COUNT(_mpc_heater_power) == HOTENDS, "MPC_HEATER_POWER must have HOTENDS items.");
- static_assert(COUNT(_mpc_block_heat_capacity) == HOTENDS, "MPC_BLOCK_HEAT_CAPACITY must have HOTENDS items.");
- static_assert(COUNT(_mpc_sensor_responsiveness) == HOTENDS, "MPC_SENSOR_RESPONSIVENESS must have HOTENDS items.");
- static_assert(COUNT(_mpc_ambient_xfer_coeff) == HOTENDS, "MPC_AMBIENT_XFER_COEFF must have HOTENDS items.");
- #if ENABLED(MPC_INCLUDE_FAN)
- static_assert(COUNT(_mpc_ambient_xfer_coeff_fan255) == HOTENDS, "MPC_AMBIENT_XFER_COEFF_FAN255 must have HOTENDS items.");
- #endif
- static_assert(COUNT(_filament_heat_capacity_permm) == HOTENDS, "FILAMENT_HEAT_CAPACITY_PERMM must have HOTENDS items.");
-
- HOTEND_LOOP() {
- MPC_t &constants = thermalManager.temp_hotend[e].constants;
- constants.heater_power = _mpc_heater_power[e];
- constants.block_heat_capacity = _mpc_block_heat_capacity[e];
- constants.sensor_responsiveness = _mpc_sensor_responsiveness[e];
- constants.ambient_xfer_coeff_fan0 = _mpc_ambient_xfer_coeff[e];
- #if ENABLED(MPC_INCLUDE_FAN)
- constants.fan255_adjustment = _mpc_ambient_xfer_coeff_fan255[e] - _mpc_ambient_xfer_coeff[e];
- #endif
- constants.filament_heat_capacity_permm = _filament_heat_capacity_permm[e];
- }
- #endif
-
- postprocess();
-
- #if EITHER(EEPROM_CHITCHAT, DEBUG_LEVELING_FEATURE)
- FSTR_P const hdsl = F("Hardcoded Default Settings Loaded");
- TERN_(HOST_EEPROM_CHITCHAT, hostui.notify(hdsl));
- DEBUG_ECHO_START(); DEBUG_ECHOLNF(hdsl);
- #endif
-
- TERN_(EXTENSIBLE_UI, ExtUI::onFactoryReset());
- }
-
- #if DISABLED(DISABLE_M503)
-
- #define CONFIG_ECHO_START() gcode.report_echo_start(forReplay)
- #define CONFIG_ECHO_MSG(V...) do{ CONFIG_ECHO_START(); SERIAL_ECHOLNPGM(V); }while(0)
- #define CONFIG_ECHO_MSG_P(V...) do{ CONFIG_ECHO_START(); SERIAL_ECHOLNPGM_P(V); }while(0)
- #define CONFIG_ECHO_HEADING(STR) gcode.report_heading(forReplay, F(STR))
-
- void M92_report(const bool echo=true, const int8_t e=-1);
-
- /**
- * M503 - Report current settings in RAM
- *
- * Unless specifically disabled, M503 is available even without EEPROM
- */
- void MarlinSettings::report(const bool forReplay) {
- //
- // Announce current units, in case inches are being displayed
- //
- CONFIG_ECHO_HEADING("Linear Units");
- CONFIG_ECHO_START();
- #if ENABLED(INCH_MODE_SUPPORT)
- SERIAL_ECHOPGM(" G2", AS_DIGIT(parser.linear_unit_factor == 1.0), " ;");
- #else
- SERIAL_ECHOPGM(" G21 ;");
- #endif
- gcode.say_units(); // " (in/mm)"
-
- //
- // M149 Temperature units
- //
- #if ENABLED(TEMPERATURE_UNITS_SUPPORT)
- gcode.M149_report(forReplay);
- #else
- CONFIG_ECHO_HEADING(STR_TEMPERATURE_UNITS);
- CONFIG_ECHO_MSG(" M149 C ; Units in Celsius");
- #endif
-
- //
- // M200 Volumetric Extrusion
- //
- IF_DISABLED(NO_VOLUMETRICS, gcode.M200_report(forReplay));
-
- //
- // M92 Steps per Unit
- //
- gcode.M92_report(forReplay);
-
- //
- // M203 Maximum feedrates (units/s)
- //
- gcode.M203_report(forReplay);
-
- //
- // M201 Maximum Acceleration (units/s2)
- //
- gcode.M201_report(forReplay);
-
- //
- // M204 Acceleration (units/s2)
- //
- gcode.M204_report(forReplay);
-
- //
- // M205 "Advanced" Settings
- //
- gcode.M205_report(forReplay);
-
- //
- // M206 Home Offset
- //
- TERN_(HAS_M206_COMMAND, gcode.M206_report(forReplay));
-
- //
- // M218 Hotend offsets
- //
- TERN_(HAS_HOTEND_OFFSET, gcode.M218_report(forReplay));
-
- //
- // Bed Leveling
- //
- #if HAS_LEVELING
-
- gcode.M420_report(forReplay);
-
- #if ENABLED(MESH_BED_LEVELING)
-
- if (leveling_is_valid()) {
- LOOP_L_N(py, GRID_MAX_POINTS_Y) {
- LOOP_L_N(px, GRID_MAX_POINTS_X) {
- CONFIG_ECHO_START();
- SERIAL_ECHOPGM(" G29 S3 I", px, " J", py);
- SERIAL_ECHOLNPAIR_F_P(SP_Z_STR, LINEAR_UNIT(bedlevel.z_values[px][py]), 5);
- }
- }
- CONFIG_ECHO_START();
- SERIAL_ECHOLNPAIR_F(" G29 S4 Z", LINEAR_UNIT(bedlevel.z_offset), 5);
- }
-
- #elif ENABLED(AUTO_BED_LEVELING_UBL)
-
- if (!forReplay) {
- SERIAL_EOL();
- bedlevel.report_state();
- SERIAL_ECHO_MSG("Active Mesh Slot ", bedlevel.storage_slot);
- SERIAL_ECHO_MSG("EEPROM can hold ", calc_num_meshes(), " meshes.\n");
- }
-
- //bedlevel.report_current_mesh(); // This is too verbose for large meshes. A better (more terse)
- // solution needs to be found.
-
- #elif ENABLED(AUTO_BED_LEVELING_BILINEAR)
-
- if (leveling_is_valid()) {
- LOOP_L_N(py, GRID_MAX_POINTS_Y) {
- LOOP_L_N(px, GRID_MAX_POINTS_X) {
- CONFIG_ECHO_START();
- SERIAL_ECHOPGM(" G29 W I", px, " J", py);
- SERIAL_ECHOLNPAIR_F_P(SP_Z_STR, LINEAR_UNIT(bedlevel.z_values[px][py]), 5);
- }
- }
- }
-
- #endif
-
- #endif // HAS_LEVELING
-
- //
- // X Axis Twist Compensation
- //
- TERN_(X_AXIS_TWIST_COMPENSATION, gcode.M423_report(forReplay));
-
- //
- // Editable Servo Angles
- //
- TERN_(EDITABLE_SERVO_ANGLES, gcode.M281_report(forReplay));
-
- //
- // Kinematic Settings
- //
- TERN_(IS_KINEMATIC, gcode.M665_report(forReplay));
-
- //
- // M666 Endstops Adjustment
- //
- #if EITHER(DELTA, HAS_EXTRA_ENDSTOPS)
- gcode.M666_report(forReplay);
- #endif
-
- //
- // Z Auto-Align
- //
- TERN_(Z_STEPPER_AUTO_ALIGN, gcode.M422_report(forReplay));
-
- //
- // LCD Preheat Settings
- //
- TERN_(HAS_PREHEAT, gcode.M145_report(forReplay));
-
- //
- // PID
- //
- TERN_(PIDTEMP, gcode.M301_report(forReplay));
- TERN_(PIDTEMPBED, gcode.M304_report(forReplay));
- TERN_(PIDTEMPCHAMBER, gcode.M309_report(forReplay));
-
- #if HAS_USER_THERMISTORS
- LOOP_L_N(i, USER_THERMISTORS)
- thermalManager.M305_report(i, forReplay);
- #endif
-
- //
- // LCD Contrast
- //
- TERN_(HAS_LCD_CONTRAST, gcode.M250_report(forReplay));
-
- //
- // Display Sleep
- //
- TERN_(HAS_GCODE_M255, gcode.M255_report(forReplay));
-
- //
- // LCD Brightness
- //
- TERN_(HAS_LCD_BRIGHTNESS, gcode.M256_report(forReplay));
-
- //
- // Controller Fan
- //
- TERN_(CONTROLLER_FAN_EDITABLE, gcode.M710_report(forReplay));
-
- //
- // Power-Loss Recovery
- //
- TERN_(POWER_LOSS_RECOVERY, gcode.M413_report(forReplay));
-
- //
- // Firmware Retraction
- //
- #if ENABLED(FWRETRACT)
- gcode.M207_report(forReplay);
- gcode.M208_report(forReplay);
- TERN_(FWRETRACT_AUTORETRACT, gcode.M209_report(forReplay));
- #endif
-
- //
- // Probe Offset
- //
- TERN_(HAS_BED_PROBE, gcode.M851_report(forReplay));
-
- //
- // Bed Skew Correction
- //
- TERN_(SKEW_CORRECTION_GCODE, gcode.M852_report(forReplay));
-
- #if HAS_TRINAMIC_CONFIG
- //
- // TMC Stepper driver current
- //
- gcode.M906_report(forReplay);
-
- //
- // TMC Hybrid Threshold
- //
- TERN_(HYBRID_THRESHOLD, gcode.M913_report(forReplay));
-
- //
- // TMC Sensorless homing thresholds
- //
- TERN_(USE_SENSORLESS, gcode.M914_report(forReplay));
- #endif
-
- //
- // TMC stepping mode
- //
- TERN_(HAS_STEALTHCHOP, gcode.M569_report(forReplay));
-
- //
- // Linear Advance
- //
- TERN_(LIN_ADVANCE, gcode.M900_report(forReplay));
-
- //
- // Motor Current (SPI or PWM)
- //
- #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM
- gcode.M907_report(forReplay);
- #endif
-
- //
- // Advanced Pause filament load & unload lengths
- //
- TERN_(ADVANCED_PAUSE_FEATURE, gcode.M603_report(forReplay));
-
- //
- // Tool-changing Parameters
- //
- E_TERN_(gcode.M217_report(forReplay));
-
- //
- // Backlash Compensation
- //
- TERN_(BACKLASH_GCODE, gcode.M425_report(forReplay));
-
- //
- // Filament Runout Sensor
- //
- TERN_(HAS_FILAMENT_SENSOR, gcode.M412_report(forReplay));
-
- #if HAS_ETHERNET
- CONFIG_ECHO_HEADING("Ethernet");
- if (!forReplay) ETH0_report();
- CONFIG_ECHO_START(); SERIAL_ECHO_SP(2); MAC_report();
- CONFIG_ECHO_START(); SERIAL_ECHO_SP(2); gcode.M552_report();
- CONFIG_ECHO_START(); SERIAL_ECHO_SP(2); gcode.M553_report();
- CONFIG_ECHO_START(); SERIAL_ECHO_SP(2); gcode.M554_report();
- #endif
-
- TERN_(HAS_MULTI_LANGUAGE, gcode.M414_report(forReplay));
-
- //
- // Model predictive control
- //
- TERN_(MPCTEMP, gcode.M306_report(forReplay));
- }
-
- #endif // !DISABLE_M503
-
- #pragma pack(pop)
|