My Marlin configs for Fabrikator Mini and CTC i3 Pro B
Вы не можете выбрать более 25 тем Темы должны начинаться с буквы или цифры, могут содержать дефисы(-) и должны содержать не более 35 символов.

Configuration.h 62KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798991001011021031041051061071081091101111121131141151161171181191201211221231241251261271281291301311321331341351361371381391401411421431441451461471481491501511521531541551561571581591601611621631641651661671681691701711721731741751761771781791801811821831841851861871881891901911921931941951961971981992002012022032042052062072082092102112122132142152162172182192202212222232242252262272282292302312322332342352362372382392402412422432442452462472482492502512522532542552562572582592602612622632642652662672682692702712722732742752762772782792802812822832842852862872882892902912922932942952962972982993003013023033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333343353363373383393403413423433443453463473483493503513523533543553563573583593603613623633643653663673683693703713723733743753763773783793803813823833843853863873883893903913923933943953963973983994004014024034044054064074084094104114124134144154164174184194204214224234244254264274284294304314324334344354364374384394404414424434444454464474484494504514524534544554564574584594604614624634644654664674684694704714724734744754764774784794804814824834844854864874884894904914924934944954964974984995005015025035045055065075085095105115125135145155165175185195205215225235245255265275285295305315325335345355365375385395405415425435445455465475485495505515525535545555565575585595605615625635645655665675685695705715725735745755765775785795805815825835845855865875885895905915925935945955965975985996006016026036046056066076086096106116126136146156166176186196206216226236246256266276286296306316326336346356366376386396406416426436446456466476486496506516526536546556566576586596606616626636646656666676686696706716726736746756766776786796806816826836846856866876886896906916926936946956966976986997007017027037047057067077087097107117127137147157167177187197207217227237247257267277287297307317327337347357367377387397407417427437447457467477487497507517527537547557567577587597607617627637647657667677687697707717727737747757767777787797807817827837847857867877887897907917927937947957967977987998008018028038048058068078088098108118128138148158168178188198208218228238248258268278288298308318328338348358368378388398408418428438448458468478488498508518528538548558568578588598608618628638648658668678688698708718728738748758768778788798808818828838848858868878888898908918928938948958968978988999009019029039049059069079089099109119129139149159169179189199209219229239249259269279289299309319329339349359369379389399409419429439449459469479489499509519529539549559569579589599609619629639649659669679689699709719729739749759769779789799809819829839849859869879889899909919929939949959969979989991000100110021003100410051006100710081009101010111012101310141015101610171018101910201021102210231024102510261027102810291030103110321033103410351036103710381039104010411042104310441045104610471048104910501051105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084108510861087108810891090109110921093109410951096109710981099110011011102110311041105110611071108110911101111111211131114111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431144114511461147114811491150115111521153115411551156115711581159116011611162116311641165116611671168116911701171117211731174117511761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198119912001201120212031204120512061207120812091210121112121213121412151216121712181219122012211222122312241225122612271228122912301231123212331234123512361237123812391240124112421243124412451246124712481249125012511252125312541255125612571258125912601261126212631264126512661267126812691270127112721273127412751276127712781279128012811282128312841285128612871288128912901291129212931294129512961297129812991300130113021303130413051306130713081309131013111312131313141315131613171318131913201321132213231324132513261327132813291330133113321333133413351336133713381339134013411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375137613771378137913801381138213831384138513861387138813891390139113921393139413951396139713981399140014011402140314041405140614071408140914101411141214131414141514161417141814191420142114221423142414251426142714281429143014311432143314341435143614371438143914401441144214431444144514461447144814491450145114521453145414551456145714581459146014611462146314641465146614671468146914701471147214731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534153515361537153815391540154115421543154415451546154715481549155015511552155315541555155615571558155915601561156215631564156515661567156815691570157115721573157415751576157715781579158015811582158315841585158615871588158915901591159215931594159515961597159815991600160116021603160416051606160716081609161016111612161316141615161616171618161916201621162216231624162516261627162816291630163116321633163416351636163716381639164016411642164316441645164616471648164916501651165216531654165516561657165816591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration.h
  24. *
  25. * Basic settings such as:
  26. *
  27. * - Type of electronics
  28. * - Type of temperature sensor
  29. * - Printer geometry
  30. * - Endstop configuration
  31. * - LCD controller
  32. * - Extra features
  33. *
  34. * Advanced settings can be found in Configuration_adv.h
  35. *
  36. */
  37. #ifndef CONFIGURATION_H
  38. #define CONFIGURATION_H
  39. #define CONFIGURATION_H_VERSION 010107
  40. //===========================================================================
  41. //============================= Getting Started =============================
  42. //===========================================================================
  43. /**
  44. * Here are some standard links for getting your machine calibrated:
  45. *
  46. * http://reprap.org/wiki/Calibration
  47. * http://youtu.be/wAL9d7FgInk
  48. * http://calculator.josefprusa.cz
  49. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  50. * http://www.thingiverse.com/thing:5573
  51. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  52. * http://www.thingiverse.com/thing:298812
  53. */
  54. //===========================================================================
  55. //============================= DELTA Printer ===============================
  56. //===========================================================================
  57. // For a Delta printer start with one of the configuration files in the
  58. // example_configurations/delta directory and customize for your machine.
  59. //
  60. //===========================================================================
  61. //============================= SCARA Printer ===============================
  62. //===========================================================================
  63. // For a SCARA printer start with the configuration files in
  64. // example_configurations/SCARA and customize for your machine.
  65. //
  66. // @section info
  67. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  68. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  69. // build by the user have been successfully uploaded into firmware.
  70. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  71. #define SHOW_BOOTSCREEN
  72. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  73. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  74. //
  75. // *** VENDORS PLEASE READ *****************************************************
  76. //
  77. // Marlin now allow you to have a vendor boot image to be displayed on machine
  78. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  79. // custom boot image and then the default Marlin boot image is shown.
  80. //
  81. // We suggest for you to take advantage of this new feature and keep the Marlin
  82. // boot image unmodified. For an example have a look at the bq Hephestos 2
  83. // example configuration folder.
  84. //
  85. //#define SHOW_CUSTOM_BOOTSCREEN
  86. // @section machine
  87. /**
  88. * Select which serial port on the board will be used for communication with the host.
  89. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  90. * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  91. *
  92. * :[0, 1, 2, 3, 4, 5, 6, 7]
  93. */
  94. #define SERIAL_PORT 0
  95. /**
  96. * This setting determines the communication speed of the printer.
  97. *
  98. * 250000 works in most cases, but you might try a lower speed if
  99. * you commonly experience drop-outs during host printing.
  100. * You may try up to 1000000 to speed up SD file transfer.
  101. *
  102. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  103. */
  104. #define BAUDRATE 250000
  105. // Enable the Bluetooth serial interface on AT90USB devices
  106. //#define BLUETOOTH
  107. // The following define selects which electronics board you have.
  108. // Please choose the name from boards.h that matches your setup
  109. #ifndef MOTHERBOARD
  110. #define MOTHERBOARD BOARD_OMCA
  111. #endif
  112. // Optional custom name for your RepStrap or other custom machine
  113. // Displayed in the LCD "Ready" message
  114. //#define CUSTOM_MACHINE_NAME "3D Printer"
  115. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  116. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  117. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  118. // @section extruder
  119. // This defines the number of extruders
  120. // :[1, 2, 3, 4, 5]
  121. #define EXTRUDERS 1
  122. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  123. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
  124. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  125. //#define SINGLENOZZLE
  126. /**
  127. * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  128. *
  129. * This device allows one stepper driver on a control board to drive
  130. * two to eight stepper motors, one at a time, in a manner suitable
  131. * for extruders.
  132. *
  133. * This option only allows the multiplexer to switch on tool-change.
  134. * Additional options to configure custom E moves are pending.
  135. */
  136. //#define MK2_MULTIPLEXER
  137. #if ENABLED(MK2_MULTIPLEXER)
  138. // Override the default DIO selector pins here, if needed.
  139. // Some pins files may provide defaults for these pins.
  140. //#define E_MUX0_PIN 40 // Always Required
  141. //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers
  142. //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers
  143. #endif
  144. // A dual extruder that uses a single stepper motor
  145. //#define SWITCHING_EXTRUDER
  146. #if ENABLED(SWITCHING_EXTRUDER)
  147. #define SWITCHING_EXTRUDER_SERVO_NR 0
  148. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  149. #if EXTRUDERS > 3
  150. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  151. #endif
  152. #endif
  153. // A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
  154. //#define SWITCHING_NOZZLE
  155. #if ENABLED(SWITCHING_NOZZLE)
  156. #define SWITCHING_NOZZLE_SERVO_NR 0
  157. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  158. //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
  159. #endif
  160. /**
  161. * Two separate X-carriages with extruders that connect to a moving part
  162. * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  163. */
  164. //#define PARKING_EXTRUDER
  165. #if ENABLED(PARKING_EXTRUDER)
  166. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  167. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  168. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
  169. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  170. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
  171. #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking
  172. #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0.
  173. #endif
  174. /**
  175. * "Mixing Extruder"
  176. * - Adds a new code, M165, to set the current mix factors.
  177. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  178. * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
  179. * - This implementation supports only a single extruder.
  180. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  181. */
  182. //#define MIXING_EXTRUDER
  183. #if ENABLED(MIXING_EXTRUDER)
  184. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  185. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  186. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  187. #endif
  188. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  189. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  190. // For the other hotends it is their distance from the extruder 0 hotend.
  191. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  192. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  193. // @section machine
  194. /**
  195. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  196. *
  197. * 0 = No Power Switch
  198. * 1 = ATX
  199. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  200. *
  201. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  202. */
  203. #define POWER_SUPPLY 1
  204. #if POWER_SUPPLY > 0
  205. // Enable this option to leave the PSU off at startup.
  206. // Power to steppers and heaters will need to be turned on with M80.
  207. //#define PS_DEFAULT_OFF
  208. #endif
  209. // @section temperature
  210. //===========================================================================
  211. //============================= Thermal Settings ============================
  212. //===========================================================================
  213. /**
  214. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  215. *
  216. * Temperature sensors available:
  217. *
  218. * -3 : thermocouple with MAX31855 (only for sensor 0)
  219. * -2 : thermocouple with MAX6675 (only for sensor 0)
  220. * -1 : thermocouple with AD595
  221. * 0 : not used
  222. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  223. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  224. * 3 : Mendel-parts thermistor (4.7k pullup)
  225. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  226. * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  227. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  228. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  229. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  230. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  231. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  232. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  233. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  234. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  235. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  236. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  237. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  238. * 66 : 4.7M High Temperature thermistor from Dyze Design
  239. * 70 : the 100K thermistor found in the bq Hephestos 2
  240. * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  241. *
  242. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  243. * (but gives greater accuracy and more stable PID)
  244. * 51 : 100k thermistor - EPCOS (1k pullup)
  245. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  246. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  247. *
  248. * 1047 : Pt1000 with 4k7 pullup
  249. * 1010 : Pt1000 with 1k pullup (non standard)
  250. * 147 : Pt100 with 4k7 pullup
  251. * 110 : Pt100 with 1k pullup (non standard)
  252. *
  253. * Use these for Testing or Development purposes. NEVER for production machine.
  254. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  255. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  256. *
  257. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  258. */
  259. #define TEMP_SENSOR_0 5
  260. #define TEMP_SENSOR_1 0
  261. #define TEMP_SENSOR_2 0
  262. #define TEMP_SENSOR_3 0
  263. #define TEMP_SENSOR_4 0
  264. #define TEMP_SENSOR_BED 5
  265. // Dummy thermistor constant temperature readings, for use with 998 and 999
  266. #define DUMMY_THERMISTOR_998_VALUE 25
  267. #define DUMMY_THERMISTOR_999_VALUE 100
  268. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  269. // from the two sensors differ too much the print will be aborted.
  270. //#define TEMP_SENSOR_1_AS_REDUNDANT
  271. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  272. // Extruder temperature must be close to target for this long before M109 returns success
  273. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  274. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  275. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  276. // Bed temperature must be close to target for this long before M190 returns success
  277. #define TEMP_BED_RESIDENCY_TIME 0 // (seconds)
  278. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  279. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  280. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  281. // to check that the wiring to the thermistor is not broken.
  282. // Otherwise this would lead to the heater being powered on all the time.
  283. #define HEATER_0_MINTEMP 5
  284. #define HEATER_1_MINTEMP 5
  285. #define HEATER_2_MINTEMP 5
  286. #define HEATER_3_MINTEMP 5
  287. #define HEATER_4_MINTEMP 5
  288. #define BED_MINTEMP 5
  289. // When temperature exceeds max temp, your heater will be switched off.
  290. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  291. // You should use MINTEMP for thermistor short/failure protection.
  292. #define HEATER_0_MAXTEMP 275
  293. #define HEATER_1_MAXTEMP 275
  294. #define HEATER_2_MAXTEMP 275
  295. #define HEATER_3_MAXTEMP 275
  296. #define HEATER_4_MAXTEMP 275
  297. #define BED_MAXTEMP 150
  298. //===========================================================================
  299. //============================= PID Settings ================================
  300. //===========================================================================
  301. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  302. // Comment the following line to disable PID and enable bang-bang.
  303. #define PIDTEMP
  304. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  305. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  306. #if ENABLED(PIDTEMP)
  307. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  308. //#define PID_DEBUG // Sends debug data to the serial port.
  309. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  310. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  311. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  312. // Set/get with gcode: M301 E[extruder number, 0-2]
  313. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  314. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  315. #define K1 0.95 //smoothing factor within the PID
  316. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  317. // J-Head Mk V-B
  318. #define DEFAULT_Kp 25.05
  319. #define DEFAULT_Ki 2.30
  320. #define DEFAULT_Kd 68.15
  321. #endif // PIDTEMP
  322. //===========================================================================
  323. //============================= PID > Bed Temperature Control ===============
  324. //===========================================================================
  325. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  326. //
  327. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  328. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  329. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  330. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  331. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  332. // shouldn't use bed PID until someone else verifies your hardware works.
  333. // If this is enabled, find your own PID constants below.
  334. //#define PIDTEMPBED
  335. //#define BED_LIMIT_SWITCHING
  336. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  337. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  338. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  339. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  340. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  341. #if ENABLED(PIDTEMPBED)
  342. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  343. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  344. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  345. #define DEFAULT_bedKp 10.00
  346. #define DEFAULT_bedKi .023
  347. #define DEFAULT_bedKd 305.4
  348. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  349. //from pidautotune
  350. //#define DEFAULT_bedKp 97.1
  351. //#define DEFAULT_bedKi 1.41
  352. //#define DEFAULT_bedKd 1675.16
  353. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  354. #endif // PIDTEMPBED
  355. // @section extruder
  356. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  357. // It also enables the M302 command to set the minimum extrusion temperature
  358. // or to allow moving the extruder regardless of the hotend temperature.
  359. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  360. #define PREVENT_COLD_EXTRUSION
  361. #define EXTRUDE_MINTEMP 170
  362. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  363. // Note that for Bowden Extruders a too-small value here may prevent loading.
  364. #define PREVENT_LENGTHY_EXTRUDE
  365. #define EXTRUDE_MAXLENGTH 200
  366. //===========================================================================
  367. //======================== Thermal Runaway Protection =======================
  368. //===========================================================================
  369. /**
  370. * Thermal Protection provides additional protection to your printer from damage
  371. * and fire. Marlin always includes safe min and max temperature ranges which
  372. * protect against a broken or disconnected thermistor wire.
  373. *
  374. * The issue: If a thermistor falls out, it will report the much lower
  375. * temperature of the air in the room, and the the firmware will keep
  376. * the heater on.
  377. *
  378. * If you get "Thermal Runaway" or "Heating failed" errors the
  379. * details can be tuned in Configuration_adv.h
  380. */
  381. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  382. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  383. //===========================================================================
  384. //============================= Mechanical Settings =========================
  385. //===========================================================================
  386. // @section machine
  387. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  388. // either in the usual order or reversed
  389. //#define COREXY
  390. //#define COREXZ
  391. //#define COREYZ
  392. //#define COREYX
  393. //#define COREZX
  394. //#define COREZY
  395. //===========================================================================
  396. //============================== Endstop Settings ===========================
  397. //===========================================================================
  398. // @section homing
  399. // Specify here all the endstop connectors that are connected to any endstop or probe.
  400. // Almost all printers will be using one per axis. Probes will use one or more of the
  401. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  402. #define USE_XMIN_PLUG
  403. #define USE_YMIN_PLUG
  404. #define USE_ZMIN_PLUG
  405. //#define USE_XMAX_PLUG
  406. //#define USE_YMAX_PLUG
  407. //#define USE_ZMAX_PLUG
  408. // coarse Endstop Settings
  409. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  410. #if DISABLED(ENDSTOPPULLUPS)
  411. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  412. //#define ENDSTOPPULLUP_XMAX
  413. //#define ENDSTOPPULLUP_YMAX
  414. //#define ENDSTOPPULLUP_ZMAX
  415. //#define ENDSTOPPULLUP_XMIN
  416. //#define ENDSTOPPULLUP_YMIN
  417. //#define ENDSTOPPULLUP_ZMIN
  418. //#define ENDSTOPPULLUP_ZMIN_PROBE
  419. #endif
  420. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  421. #define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  422. #define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  423. #define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  424. #define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  425. #define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  426. #define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  427. #define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
  428. // Enable this feature if all enabled endstop pins are interrupt-capable.
  429. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  430. //#define ENDSTOP_INTERRUPTS_FEATURE
  431. //=============================================================================
  432. //============================== Movement Settings ============================
  433. //=============================================================================
  434. // @section motion
  435. /**
  436. * Default Settings
  437. *
  438. * These settings can be reset by M502
  439. *
  440. * Note that if EEPROM is enabled, saved values will override these.
  441. */
  442. /**
  443. * With this option each E stepper can have its own factors for the
  444. * following movement settings. If fewer factors are given than the
  445. * total number of extruders, the last value applies to the rest.
  446. */
  447. //#define DISTINCT_E_FACTORS
  448. /**
  449. * Default Axis Steps Per Unit (steps/mm)
  450. * Override with M92
  451. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  452. */
  453. #define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 600 } // David TVRR
  454. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 79.87, 79.87, 2566, 563.78 } // Al's TVRR
  455. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 81.26, 80.01, 2561, 599.14 } // Michel TVRR old
  456. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 739.65 } // Michel TVRR
  457. /**
  458. * Default Max Feed Rate (mm/s)
  459. * Override with M203
  460. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  461. */
  462. #define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 45 } // David TVRR
  463. /**
  464. * Default Max Acceleration (change/s) change = mm/s
  465. * (Maximum start speed for accelerated moves)
  466. * Override with M201
  467. * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  468. */
  469. #define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
  470. /* MICHEL: This has an impact on the "ripples" in print walls */
  471. /**
  472. * Default Acceleration (change/s) change = mm/s
  473. * Override with M204
  474. *
  475. * M204 P Acceleration
  476. * M204 R Retract Acceleration
  477. * M204 T Travel Acceleration
  478. */
  479. #define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
  480. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  481. #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves
  482. /**
  483. * Default Jerk (mm/s)
  484. * Override with M205 X Y Z E
  485. *
  486. * "Jerk" specifies the minimum speed change that requires acceleration.
  487. * When changing speed and direction, if the difference is less than the
  488. * value set here, it may happen instantaneously.
  489. */
  490. #define DEFAULT_XJERK 20.0
  491. #define DEFAULT_YJERK 20.0
  492. #define DEFAULT_ZJERK 0.4
  493. #define DEFAULT_EJERK 5.0
  494. //===========================================================================
  495. //============================= Z Probe Options =============================
  496. //===========================================================================
  497. // @section probes
  498. //
  499. // See http://marlinfw.org/docs/configuration/probes.html
  500. //
  501. /**
  502. * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  503. *
  504. * Enable this option for a probe connected to the Z Min endstop pin.
  505. */
  506. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  507. /**
  508. * Z_MIN_PROBE_ENDSTOP
  509. *
  510. * Enable this option for a probe connected to any pin except Z-Min.
  511. * (By default Marlin assumes the Z-Max endstop pin.)
  512. * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
  513. *
  514. * - The simplest option is to use a free endstop connector.
  515. * - Use 5V for powered (usually inductive) sensors.
  516. *
  517. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  518. * - For simple switches connect...
  519. * - normally-closed switches to GND and D32.
  520. * - normally-open switches to 5V and D32.
  521. *
  522. * WARNING: Setting the wrong pin may have unexpected and potentially
  523. * disastrous consequences. Use with caution and do your homework.
  524. *
  525. */
  526. //#define Z_MIN_PROBE_ENDSTOP
  527. /**
  528. * Probe Type
  529. *
  530. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  531. * Activate one of these to use Auto Bed Leveling below.
  532. */
  533. /**
  534. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  535. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  536. * or (with LCD_BED_LEVELING) the LCD controller.
  537. */
  538. //#define PROBE_MANUALLY
  539. /**
  540. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  541. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  542. */
  543. //#define FIX_MOUNTED_PROBE
  544. /**
  545. * Z Servo Probe, such as an endstop switch on a rotating arm.
  546. */
  547. //#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
  548. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  549. /**
  550. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  551. */
  552. //#define BLTOUCH
  553. #if ENABLED(BLTOUCH)
  554. //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
  555. #endif
  556. /**
  557. * Enable one or more of the following if probing seems unreliable.
  558. * Heaters and/or fans can be disabled during probing to minimize electrical
  559. * noise. A delay can also be added to allow noise and vibration to settle.
  560. * These options are most useful for the BLTouch probe, but may also improve
  561. * readings with inductive probes and piezo sensors.
  562. */
  563. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  564. //#define PROBING_FANS_OFF // Turn fans off when probing
  565. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  566. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  567. //#define SOLENOID_PROBE
  568. // A sled-mounted probe like those designed by Charles Bell.
  569. //#define Z_PROBE_SLED
  570. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  571. //
  572. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  573. //
  574. /**
  575. * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  576. * X and Y offsets must be integers.
  577. *
  578. * In the following example the X and Y offsets are both positive:
  579. * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  580. * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  581. *
  582. * +-- BACK ---+
  583. * | |
  584. * L | (+) P | R <-- probe (20,20)
  585. * E | | I
  586. * F | (-) N (+) | G <-- nozzle (10,10)
  587. * T | | H
  588. * | (-) | T
  589. * | |
  590. * O-- FRONT --+
  591. * (0,0)
  592. */
  593. #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
  594. #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
  595. #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
  596. // X and Y axis travel speed (mm/m) between probes
  597. #define XY_PROBE_SPEED 8000
  598. // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
  599. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  600. // Speed for the "accurate" probe of each point
  601. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  602. // Use double touch for probing
  603. //#define PROBE_DOUBLE_TOUCH
  604. /**
  605. * Z probes require clearance when deploying, stowing, and moving between
  606. * probe points to avoid hitting the bed and other hardware.
  607. * Servo-mounted probes require extra space for the arm to rotate.
  608. * Inductive probes need space to keep from triggering early.
  609. *
  610. * Use these settings to specify the distance (mm) to raise the probe (or
  611. * lower the bed). The values set here apply over and above any (negative)
  612. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  613. * Only integer values >= 1 are valid here.
  614. *
  615. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  616. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  617. */
  618. #define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
  619. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  620. // For M851 give a range for adjusting the Z probe offset
  621. #define Z_PROBE_OFFSET_RANGE_MIN -20
  622. #define Z_PROBE_OFFSET_RANGE_MAX 20
  623. // Enable the M48 repeatability test to test probe accuracy
  624. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  625. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  626. // :{ 0:'Low', 1:'High' }
  627. #define X_ENABLE_ON 1
  628. #define Y_ENABLE_ON 1
  629. #define Z_ENABLE_ON 1
  630. #define E_ENABLE_ON 1 // For all extruders
  631. // Disables axis stepper immediately when it's not being used.
  632. // WARNING: When motors turn off there is a chance of losing position accuracy!
  633. #define DISABLE_X false
  634. #define DISABLE_Y false
  635. #define DISABLE_Z false
  636. // Warn on display about possibly reduced accuracy
  637. //#define DISABLE_REDUCED_ACCURACY_WARNING
  638. // @section extruder
  639. #define DISABLE_E false // For all extruders
  640. #define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
  641. // @section machine
  642. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  643. #define INVERT_X_DIR false
  644. #define INVERT_Y_DIR false
  645. #define INVERT_Z_DIR true
  646. // Enable this option for Toshiba stepper drivers
  647. #define CONFIG_STEPPERS_TOSHIBA
  648. // @section extruder
  649. // For direct drive extruder v9 set to true, for geared extruder set to false.
  650. #define INVERT_E0_DIR false
  651. #define INVERT_E1_DIR false
  652. #define INVERT_E2_DIR false
  653. #define INVERT_E3_DIR false
  654. #define INVERT_E4_DIR false
  655. // @section homing
  656. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
  657. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  658. // Be sure you have this distance over your Z_MAX_POS in case.
  659. // Direction of endstops when homing; 1=MAX, -1=MIN
  660. // :[-1,1]
  661. #define X_HOME_DIR -1
  662. #define Y_HOME_DIR -1
  663. #define Z_HOME_DIR -1
  664. // @section machine
  665. // The size of the print bed
  666. #define X_BED_SIZE 205
  667. #define Y_BED_SIZE 205
  668. // Travel limits (mm) after homing, corresponding to endstop positions.
  669. #define X_MIN_POS 0
  670. #define Y_MIN_POS 0
  671. #define Z_MIN_POS 0
  672. #define X_MAX_POS X_BED_SIZE
  673. #define Y_MAX_POS Y_BED_SIZE
  674. #define Z_MAX_POS 120
  675. /**
  676. * Software Endstops
  677. *
  678. * - Prevent moves outside the set machine bounds.
  679. * - Individual axes can be disabled, if desired.
  680. * - X and Y only apply to Cartesian robots.
  681. * - Use 'M211' to set software endstops on/off or report current state
  682. */
  683. // Min software endstops curtail movement below minimum coordinate bounds
  684. #define MIN_SOFTWARE_ENDSTOPS
  685. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  686. #define MIN_SOFTWARE_ENDSTOP_X
  687. #define MIN_SOFTWARE_ENDSTOP_Y
  688. #define MIN_SOFTWARE_ENDSTOP_Z
  689. #endif
  690. // Max software endstops curtail movement above maximum coordinate bounds
  691. #define MAX_SOFTWARE_ENDSTOPS
  692. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  693. #define MAX_SOFTWARE_ENDSTOP_X
  694. #define MAX_SOFTWARE_ENDSTOP_Y
  695. #define MAX_SOFTWARE_ENDSTOP_Z
  696. #endif
  697. /**
  698. * Filament Runout Sensor
  699. * A mechanical or opto endstop is used to check for the presence of filament.
  700. *
  701. * RAMPS-based boards use SERVO3_PIN.
  702. * For other boards you may need to define FIL_RUNOUT_PIN.
  703. * By default the firmware assumes HIGH = has filament, LOW = ran out
  704. */
  705. //#define FILAMENT_RUNOUT_SENSOR
  706. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  707. #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  708. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  709. #define FILAMENT_RUNOUT_SCRIPT "M600"
  710. #endif
  711. //===========================================================================
  712. //=============================== Bed Leveling ==============================
  713. //===========================================================================
  714. // @section bedlevel
  715. /**
  716. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  717. * and behavior of G29 will change depending on your selection.
  718. *
  719. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  720. *
  721. * - AUTO_BED_LEVELING_3POINT
  722. * Probe 3 arbitrary points on the bed (that aren't collinear)
  723. * You specify the XY coordinates of all 3 points.
  724. * The result is a single tilted plane. Best for a flat bed.
  725. *
  726. * - AUTO_BED_LEVELING_LINEAR
  727. * Probe several points in a grid.
  728. * You specify the rectangle and the density of sample points.
  729. * The result is a single tilted plane. Best for a flat bed.
  730. *
  731. * - AUTO_BED_LEVELING_BILINEAR
  732. * Probe several points in a grid.
  733. * You specify the rectangle and the density of sample points.
  734. * The result is a mesh, best for large or uneven beds.
  735. *
  736. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  737. * A comprehensive bed leveling system combining the features and benefits
  738. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  739. * Validation and Mesh Editing systems. Currently, UBL is only checked out
  740. * for Cartesian Printers. That said, it was primarily designed to correct
  741. * poor quality Delta Printers. If you feel adventurous and have a Delta,
  742. * please post an issue if something doesn't work correctly. Initially,
  743. * you will need to set a reduced bed size so you have a rectangular area
  744. * to test on.
  745. *
  746. * - MESH_BED_LEVELING
  747. * Probe a grid manually
  748. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  749. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  750. * leveling in steps so you can manually adjust the Z height at each grid-point.
  751. * With an LCD controller the process is guided step-by-step.
  752. */
  753. //#define AUTO_BED_LEVELING_3POINT
  754. //#define AUTO_BED_LEVELING_LINEAR
  755. //#define AUTO_BED_LEVELING_BILINEAR
  756. //#define AUTO_BED_LEVELING_UBL
  757. //#define MESH_BED_LEVELING
  758. /**
  759. * Enable detailed logging of G28, G29, M48, etc.
  760. * Turn on with the command 'M111 S32'.
  761. * NOTE: Requires a lot of PROGMEM!
  762. */
  763. //#define DEBUG_LEVELING_FEATURE
  764. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  765. // Gradually reduce leveling correction until a set height is reached,
  766. // at which point movement will be level to the machine's XY plane.
  767. // The height can be set with M420 Z<height>
  768. #define ENABLE_LEVELING_FADE_HEIGHT
  769. /**
  770. * Enable the G26 Mesh Validation Pattern tool.
  771. */
  772. //#define G26_MESH_VALIDATION // Enable G26 mesh validation
  773. #if ENABLED(G26_MESH_VALIDATION)
  774. #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
  775. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
  776. #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  777. #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  778. #endif
  779. #endif
  780. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  781. // Set the number of grid points per dimension.
  782. #define GRID_MAX_POINTS_X 3
  783. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  784. // Set the boundaries for probing (where the probe can reach).
  785. #define LEFT_PROBE_BED_POSITION 15
  786. #define RIGHT_PROBE_BED_POSITION 170
  787. #define FRONT_PROBE_BED_POSITION 20
  788. #define BACK_PROBE_BED_POSITION 170
  789. // The Z probe minimum outer margin (to validate G29 parameters).
  790. #define MIN_PROBE_EDGE 10
  791. // Probe along the Y axis, advancing X after each column
  792. //#define PROBE_Y_FIRST
  793. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  794. // Beyond the probed grid, continue the implied tilt?
  795. // Default is to maintain the height of the nearest edge.
  796. //#define EXTRAPOLATE_BEYOND_GRID
  797. //
  798. // Experimental Subdivision of the grid by Catmull-Rom method.
  799. // Synthesizes intermediate points to produce a more detailed mesh.
  800. //
  801. //#define ABL_BILINEAR_SUBDIVISION
  802. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  803. // Number of subdivisions between probe points
  804. #define BILINEAR_SUBDIVISIONS 3
  805. #endif
  806. #endif
  807. #elif ENABLED(AUTO_BED_LEVELING_3POINT)
  808. // 3 arbitrary points to probe.
  809. // A simple cross-product is used to estimate the plane of the bed.
  810. #define ABL_PROBE_PT_1_X 15
  811. #define ABL_PROBE_PT_1_Y 180
  812. #define ABL_PROBE_PT_2_X 15
  813. #define ABL_PROBE_PT_2_Y 20
  814. #define ABL_PROBE_PT_3_X 170
  815. #define ABL_PROBE_PT_3_Y 20
  816. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  817. //===========================================================================
  818. //========================= Unified Bed Leveling ============================
  819. //===========================================================================
  820. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  821. #define MESH_INSET 1 // Mesh inset margin on print area
  822. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  823. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  824. #define UBL_PROBE_PT_1_X 39 // Probing points for 3-Point leveling of the mesh
  825. #define UBL_PROBE_PT_1_Y 180
  826. #define UBL_PROBE_PT_2_X 39
  827. #define UBL_PROBE_PT_2_Y 20
  828. #define UBL_PROBE_PT_3_X 180
  829. #define UBL_PROBE_PT_3_Y 20
  830. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  831. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  832. #elif ENABLED(MESH_BED_LEVELING)
  833. //===========================================================================
  834. //=================================== Mesh ==================================
  835. //===========================================================================
  836. #define MESH_INSET 10 // Mesh inset margin on print area
  837. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  838. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  839. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  840. #endif // BED_LEVELING
  841. /**
  842. * Use the LCD controller for bed leveling
  843. * Requires MESH_BED_LEVELING or PROBE_MANUALLY
  844. */
  845. //#define LCD_BED_LEVELING
  846. #if ENABLED(LCD_BED_LEVELING)
  847. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  848. #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
  849. #endif
  850. // Add a menu item to move between bed corners for manual bed adjustment
  851. //#define LEVEL_BED_CORNERS
  852. /**
  853. * Commands to execute at the end of G29 probing.
  854. * Useful to retract or move the Z probe out of the way.
  855. */
  856. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  857. // @section homing
  858. // The center of the bed is at (X=0, Y=0)
  859. //#define BED_CENTER_AT_0_0
  860. // Manually set the home position. Leave these undefined for automatic settings.
  861. // For DELTA this is the top-center of the Cartesian print volume.
  862. //#define MANUAL_X_HOME_POS 0
  863. //#define MANUAL_Y_HOME_POS 0
  864. //#define MANUAL_Z_HOME_POS 0
  865. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  866. //
  867. // With this feature enabled:
  868. //
  869. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  870. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  871. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  872. // - Prevent Z homing when the Z probe is outside bed area.
  873. //
  874. //#define Z_SAFE_HOMING
  875. #if ENABLED(Z_SAFE_HOMING)
  876. #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
  877. #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
  878. #endif
  879. // Homing speeds (mm/m)
  880. #define HOMING_FEEDRATE_XY (50*60)
  881. #define HOMING_FEEDRATE_Z (4*60)
  882. //=============================================================================
  883. //============================= Additional Features ===========================
  884. //=============================================================================
  885. // @section extras
  886. //
  887. // EEPROM
  888. //
  889. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  890. // M500 - stores parameters in EEPROM
  891. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  892. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  893. //
  894. //#define EEPROM_SETTINGS // Enable for M500 and M501 commands
  895. //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
  896. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  897. //
  898. // Host Keepalive
  899. //
  900. // When enabled Marlin will send a busy status message to the host
  901. // every couple of seconds when it can't accept commands.
  902. //
  903. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  904. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  905. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  906. //
  907. // M100 Free Memory Watcher
  908. //
  909. //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
  910. //
  911. // G20/G21 Inch mode support
  912. //
  913. //#define INCH_MODE_SUPPORT
  914. //
  915. // M149 Set temperature units support
  916. //
  917. //#define TEMPERATURE_UNITS_SUPPORT
  918. // @section temperature
  919. // Preheat Constants
  920. #define PREHEAT_1_TEMP_HOTEND 180
  921. #define PREHEAT_1_TEMP_BED 70
  922. #define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
  923. #define PREHEAT_2_TEMP_HOTEND 240
  924. #define PREHEAT_2_TEMP_BED 100
  925. #define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
  926. /**
  927. * Nozzle Park -- EXPERIMENTAL
  928. *
  929. * Park the nozzle at the given XYZ position on idle or G27.
  930. *
  931. * The "P" parameter controls the action applied to the Z axis:
  932. *
  933. * P0 (Default) If Z is below park Z raise the nozzle.
  934. * P1 Raise the nozzle always to Z-park height.
  935. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  936. */
  937. //#define NOZZLE_PARK_FEATURE
  938. #if ENABLED(NOZZLE_PARK_FEATURE)
  939. // Specify a park position as { X, Y, Z }
  940. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  941. #endif
  942. /**
  943. * Clean Nozzle Feature -- EXPERIMENTAL
  944. *
  945. * Adds the G12 command to perform a nozzle cleaning process.
  946. *
  947. * Parameters:
  948. * P Pattern
  949. * S Strokes / Repetitions
  950. * T Triangles (P1 only)
  951. *
  952. * Patterns:
  953. * P0 Straight line (default). This process requires a sponge type material
  954. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  955. * between the start / end points.
  956. *
  957. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  958. * number of zig-zag triangles to do. "S" defines the number of strokes.
  959. * Zig-zags are done in whichever is the narrower dimension.
  960. * For example, "G12 P1 S1 T3" will execute:
  961. *
  962. * --
  963. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  964. * | | / \ / \ / \ |
  965. * A | | / \ / \ / \ |
  966. * | | / \ / \ / \ |
  967. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  968. * -- +--------------------------------+
  969. * |________|_________|_________|
  970. * T1 T2 T3
  971. *
  972. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  973. * "R" specifies the radius. "S" specifies the stroke count.
  974. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  975. *
  976. * Caveats: The ending Z should be the same as starting Z.
  977. * Attention: EXPERIMENTAL. G-code arguments may change.
  978. *
  979. */
  980. //#define NOZZLE_CLEAN_FEATURE
  981. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  982. // Default number of pattern repetitions
  983. #define NOZZLE_CLEAN_STROKES 12
  984. // Default number of triangles
  985. #define NOZZLE_CLEAN_TRIANGLES 3
  986. // Specify positions as { X, Y, Z }
  987. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  988. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  989. // Circular pattern radius
  990. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  991. // Circular pattern circle fragments number
  992. #define NOZZLE_CLEAN_CIRCLE_FN 10
  993. // Middle point of circle
  994. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  995. // Moves the nozzle to the initial position
  996. #define NOZZLE_CLEAN_GOBACK
  997. #endif
  998. /**
  999. * Print Job Timer
  1000. *
  1001. * Automatically start and stop the print job timer on M104/M109/M190.
  1002. *
  1003. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  1004. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  1005. * M190 (bed, wait) - high temp = start timer, low temp = none
  1006. *
  1007. * The timer can also be controlled with the following commands:
  1008. *
  1009. * M75 - Start the print job timer
  1010. * M76 - Pause the print job timer
  1011. * M77 - Stop the print job timer
  1012. */
  1013. #define PRINTJOB_TIMER_AUTOSTART
  1014. /**
  1015. * Print Counter
  1016. *
  1017. * Track statistical data such as:
  1018. *
  1019. * - Total print jobs
  1020. * - Total successful print jobs
  1021. * - Total failed print jobs
  1022. * - Total time printing
  1023. *
  1024. * View the current statistics with M78.
  1025. */
  1026. //#define PRINTCOUNTER
  1027. //=============================================================================
  1028. //============================= LCD and SD support ============================
  1029. //=============================================================================
  1030. // @section lcd
  1031. /**
  1032. * LCD LANGUAGE
  1033. *
  1034. * Select the language to display on the LCD. These languages are available:
  1035. *
  1036. * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl,
  1037. * hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8,
  1038. * tr, uk, zh_CN, zh_TW, test
  1039. *
  1040. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
  1041. */
  1042. #define LCD_LANGUAGE en
  1043. /**
  1044. * LCD Character Set
  1045. *
  1046. * Note: This option is NOT applicable to Graphical Displays.
  1047. *
  1048. * All character-based LCDs provide ASCII plus one of these
  1049. * language extensions:
  1050. *
  1051. * - JAPANESE ... the most common
  1052. * - WESTERN ... with more accented characters
  1053. * - CYRILLIC ... for the Russian language
  1054. *
  1055. * To determine the language extension installed on your controller:
  1056. *
  1057. * - Compile and upload with LCD_LANGUAGE set to 'test'
  1058. * - Click the controller to view the LCD menu
  1059. * - The LCD will display Japanese, Western, or Cyrillic text
  1060. *
  1061. * See http://marlinfw.org/docs/development/lcd_language.html
  1062. *
  1063. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1064. */
  1065. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1066. /**
  1067. * LCD TYPE
  1068. *
  1069. * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1070. * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display.
  1071. * (These options will be enabled automatically for most displays.)
  1072. *
  1073. * IMPORTANT: The U8glib library is required for Full Graphic Display!
  1074. * https://github.com/olikraus/U8glib_Arduino
  1075. */
  1076. //#define ULTRA_LCD // Character based
  1077. //#define DOGLCD // Full graphics display
  1078. /**
  1079. * SD CARD
  1080. *
  1081. * SD Card support is disabled by default. If your controller has an SD slot,
  1082. * you must uncomment the following option or it won't work.
  1083. *
  1084. */
  1085. //#define SDSUPPORT
  1086. /**
  1087. * SD CARD: SPI SPEED
  1088. *
  1089. * Enable one of the following items for a slower SPI transfer speed.
  1090. * This may be required to resolve "volume init" errors.
  1091. */
  1092. //#define SPI_SPEED SPI_HALF_SPEED
  1093. //#define SPI_SPEED SPI_QUARTER_SPEED
  1094. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1095. /**
  1096. * SD CARD: ENABLE CRC
  1097. *
  1098. * Use CRC checks and retries on the SD communication.
  1099. */
  1100. //#define SD_CHECK_AND_RETRY
  1101. //
  1102. // ENCODER SETTINGS
  1103. //
  1104. // This option overrides the default number of encoder pulses needed to
  1105. // produce one step. Should be increased for high-resolution encoders.
  1106. //
  1107. //#define ENCODER_PULSES_PER_STEP 1
  1108. //
  1109. // Use this option to override the number of step signals required to
  1110. // move between next/prev menu items.
  1111. //
  1112. //#define ENCODER_STEPS_PER_MENU_ITEM 5
  1113. /**
  1114. * Encoder Direction Options
  1115. *
  1116. * Test your encoder's behavior first with both options disabled.
  1117. *
  1118. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1119. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1120. * Reversed Value Editing only? Enable BOTH options.
  1121. */
  1122. //
  1123. // This option reverses the encoder direction everywhere.
  1124. //
  1125. // Set this option if CLOCKWISE causes values to DECREASE
  1126. //
  1127. //#define REVERSE_ENCODER_DIRECTION
  1128. //
  1129. // This option reverses the encoder direction for navigating LCD menus.
  1130. //
  1131. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1132. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1133. //
  1134. //#define REVERSE_MENU_DIRECTION
  1135. //
  1136. // Individual Axis Homing
  1137. //
  1138. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1139. //
  1140. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1141. //
  1142. // SPEAKER/BUZZER
  1143. //
  1144. // If you have a speaker that can produce tones, enable it here.
  1145. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1146. //
  1147. //#define SPEAKER
  1148. //
  1149. // The duration and frequency for the UI feedback sound.
  1150. // Set these to 0 to disable audio feedback in the LCD menus.
  1151. //
  1152. // Note: Test audio output with the G-Code:
  1153. // M300 S<frequency Hz> P<duration ms>
  1154. //
  1155. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1156. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1157. //
  1158. // CONTROLLER TYPE: Standard
  1159. //
  1160. // Marlin supports a wide variety of controllers.
  1161. // Enable one of the following options to specify your controller.
  1162. //
  1163. //
  1164. // ULTIMAKER Controller.
  1165. //
  1166. //#define ULTIMAKERCONTROLLER
  1167. //
  1168. // ULTIPANEL as seen on Thingiverse.
  1169. //
  1170. //#define ULTIPANEL
  1171. //
  1172. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1173. // http://reprap.org/wiki/PanelOne
  1174. //
  1175. //#define PANEL_ONE
  1176. //
  1177. // MaKr3d Makr-Panel with graphic controller and SD support.
  1178. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1179. //
  1180. //#define MAKRPANEL
  1181. //
  1182. // ReprapWorld Graphical LCD
  1183. // https://reprapworld.com/?products_details&products_id/1218
  1184. //
  1185. //#define REPRAPWORLD_GRAPHICAL_LCD
  1186. //
  1187. // Activate one of these if you have a Panucatt Devices
  1188. // Viki 2.0 or mini Viki with Graphic LCD
  1189. // http://panucatt.com
  1190. //
  1191. //#define VIKI2
  1192. //#define miniVIKI
  1193. //
  1194. // Adafruit ST7565 Full Graphic Controller.
  1195. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1196. //
  1197. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1198. //
  1199. // RepRapDiscount Smart Controller.
  1200. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1201. //
  1202. // Note: Usually sold with a white PCB.
  1203. //
  1204. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1205. //
  1206. // GADGETS3D G3D LCD/SD Controller
  1207. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1208. //
  1209. // Note: Usually sold with a blue PCB.
  1210. //
  1211. //#define G3D_PANEL
  1212. //
  1213. // RepRapDiscount FULL GRAPHIC Smart Controller
  1214. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1215. //
  1216. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1217. //
  1218. // MakerLab Mini Panel with graphic
  1219. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1220. //
  1221. //#define MINIPANEL
  1222. //
  1223. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1224. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1225. //
  1226. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1227. // is pressed, a value of 10.0 means 10mm per click.
  1228. //
  1229. //#define REPRAPWORLD_KEYPAD
  1230. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1231. //
  1232. // RigidBot Panel V1.0
  1233. // http://www.inventapart.com/
  1234. //
  1235. //#define RIGIDBOT_PANEL
  1236. //
  1237. // BQ LCD Smart Controller shipped by
  1238. // default with the BQ Hephestos 2 and Witbox 2.
  1239. //
  1240. //#define BQ_LCD_SMART_CONTROLLER
  1241. //
  1242. // Cartesio UI
  1243. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1244. //
  1245. //#define CARTESIO_UI
  1246. //
  1247. // ANET_10 Controller supported displays.
  1248. //
  1249. //#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1250. // This LCD is known to be susceptible to electrical interference
  1251. // which scrambles the display. Pressing any button clears it up.
  1252. //#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1253. // A clone of the RepRapDiscount full graphics display but with
  1254. // different pins/wiring (see pins_ANET_10.h).
  1255. //
  1256. // LCD for Melzi Card with Graphical LCD
  1257. //
  1258. //#define LCD_FOR_MELZI
  1259. //
  1260. // CONTROLLER TYPE: I2C
  1261. //
  1262. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1263. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1264. //
  1265. //
  1266. // Elefu RA Board Control Panel
  1267. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1268. //
  1269. //#define RA_CONTROL_PANEL
  1270. //
  1271. // Sainsmart YW Robot (LCM1602) LCD Display
  1272. //
  1273. // Note: This controller requires F.Malpartida's LiquidCrystal_I2C library
  1274. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1275. //
  1276. //#define LCD_I2C_SAINSMART_YWROBOT
  1277. //
  1278. // Generic LCM1602 LCD adapter
  1279. //
  1280. //#define LCM1602
  1281. //
  1282. // PANELOLU2 LCD with status LEDs,
  1283. // separate encoder and click inputs.
  1284. //
  1285. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1286. // For more info: https://github.com/lincomatic/LiquidTWI2
  1287. //
  1288. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1289. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1290. //
  1291. //#define LCD_I2C_PANELOLU2
  1292. //
  1293. // Panucatt VIKI LCD with status LEDs,
  1294. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1295. //
  1296. //#define LCD_I2C_VIKI
  1297. //
  1298. // SSD1306 OLED full graphics generic display
  1299. //
  1300. //#define U8GLIB_SSD1306
  1301. //
  1302. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1303. //
  1304. //#define SAV_3DGLCD
  1305. #if ENABLED(SAV_3DGLCD)
  1306. //#define U8GLIB_SSD1306
  1307. #define U8GLIB_SH1106
  1308. #endif
  1309. //
  1310. // CONTROLLER TYPE: Shift register panels
  1311. //
  1312. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1313. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1314. //
  1315. //#define SAV_3DLCD
  1316. //
  1317. // TinyBoy2 128x64 OLED / Encoder Panel
  1318. //
  1319. //#define OLED_PANEL_TINYBOY2
  1320. //
  1321. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1322. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1323. //
  1324. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1325. //
  1326. // MKS MINI12864 with graphic controller and SD support
  1327. // http://reprap.org/wiki/MKS_MINI_12864
  1328. //
  1329. //#define MKS_MINI_12864
  1330. //
  1331. // Factory display for Creality CR-10
  1332. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1333. //
  1334. // This is RAMPS-compatible using a single 10-pin connector.
  1335. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1336. //
  1337. //#define CR10_STOCKDISPLAY
  1338. //
  1339. // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
  1340. // http://reprap.org/wiki/MKS_12864OLED
  1341. //
  1342. // Tiny, but very sharp OLED display
  1343. //
  1344. //#define MKS_12864OLED
  1345. // Silvergate GLCD controller
  1346. // http://github.com/android444/Silvergate
  1347. //
  1348. //#define SILVER_GATE_GLCD_CONTROLLER
  1349. //=============================================================================
  1350. //=============================== Extra Features ==============================
  1351. //=============================================================================
  1352. // @section extras
  1353. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1354. //#define FAST_PWM_FAN
  1355. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1356. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1357. // is too low, you should also increment SOFT_PWM_SCALE.
  1358. //#define FAN_SOFT_PWM
  1359. // Incrementing this by 1 will double the software PWM frequency,
  1360. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1361. // However, control resolution will be halved for each increment;
  1362. // at zero value, there are 128 effective control positions.
  1363. #define SOFT_PWM_SCALE 0
  1364. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1365. // be used to mitigate the associated resolution loss. If enabled,
  1366. // some of the PWM cycles are stretched so on average the desired
  1367. // duty cycle is attained.
  1368. //#define SOFT_PWM_DITHER
  1369. // Temperature status LEDs that display the hotend and bed temperature.
  1370. // If all hotends, bed temperature, and target temperature are under 54C
  1371. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1372. //#define TEMP_STAT_LEDS
  1373. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1374. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1375. //#define PHOTOGRAPH_PIN 23
  1376. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1377. //#define SF_ARC_FIX
  1378. // Support for the BariCUDA Paste Extruder
  1379. //#define BARICUDA
  1380. // Support for BlinkM/CyzRgb
  1381. //#define BLINKM
  1382. // Support for PCA9632 PWM LED driver
  1383. //#define PCA9632
  1384. /**
  1385. * RGB LED / LED Strip Control
  1386. *
  1387. * Enable support for an RGB LED connected to 5V digital pins, or
  1388. * an RGB Strip connected to MOSFETs controlled by digital pins.
  1389. *
  1390. * Adds the M150 command to set the LED (or LED strip) color.
  1391. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1392. * luminance values can be set from 0 to 255.
  1393. * For Neopixel LED an overall brightness parameter is also available.
  1394. *
  1395. * *** CAUTION ***
  1396. * LED Strips require a MOFSET Chip between PWM lines and LEDs,
  1397. * as the Arduino cannot handle the current the LEDs will require.
  1398. * Failure to follow this precaution can destroy your Arduino!
  1399. * NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1400. * more current than the Arduino 5V linear regulator can produce.
  1401. * *** CAUTION ***
  1402. *
  1403. * LED Type. Enable only one of the following two options.
  1404. *
  1405. */
  1406. //#define RGB_LED
  1407. //#define RGBW_LED
  1408. #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1409. #define RGB_LED_R_PIN 34
  1410. #define RGB_LED_G_PIN 43
  1411. #define RGB_LED_B_PIN 35
  1412. #define RGB_LED_W_PIN -1
  1413. #endif
  1414. // Support for Adafruit Neopixel LED driver
  1415. //#define NEOPIXEL_LED
  1416. #if ENABLED(NEOPIXEL_LED)
  1417. #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1418. #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
  1419. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
  1420. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1421. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  1422. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  1423. #endif
  1424. /**
  1425. * Printer Event LEDs
  1426. *
  1427. * During printing, the LEDs will reflect the printer status:
  1428. *
  1429. * - Gradually change from blue to violet as the heated bed gets to target temp
  1430. * - Gradually change from violet to red as the hotend gets to temperature
  1431. * - Change to white to illuminate work surface
  1432. * - Change to green once print has finished
  1433. * - Turn off after the print has finished and the user has pushed a button
  1434. */
  1435. #if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
  1436. #define PRINTER_EVENT_LEDS
  1437. #endif
  1438. /**
  1439. * R/C SERVO support
  1440. * Sponsored by TrinityLabs, Reworked by codexmas
  1441. */
  1442. /**
  1443. * Number of servos
  1444. *
  1445. * For some servo-related options NUM_SERVOS will be set automatically.
  1446. * Set this manually if there are extra servos needing manual control.
  1447. * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1448. */
  1449. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1450. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1451. // 300ms is a good value but you can try less delay.
  1452. // If the servo can't reach the requested position, increase it.
  1453. #define SERVO_DELAY { 300 }
  1454. // Servo deactivation
  1455. //
  1456. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1457. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1458. #endif // CONFIGURATION_H